Cisco Unified IP Phone 6921, 6941, 6945, and 6961 Administration Guide for Cisco Unified CM 8.6 (SCCP and SIP)
Cisco Unified IP Phone Non-Lockable Wall Mount
Downloads: This chapterpdf (PDF - 1.12MB) The complete bookPDF (PDF - 7.0MB) | Feedback

Cisco Unified IP Phone Non-Lockable Wall Mount

Table Of Contents

Cisco Unified IP Phone Non-Lockable Wall Mount

ADA Non-Lockable Wall Mount Kit for 6900 Series

Components

Before You Begin

Install Non-Lockable Wall Mount Kit for Phone

Remove Phone from Non-Lockable Wall Mount


Cisco Unified IP Phone Non-Lockable Wall Mount


This appendix contains information on installing the following product:

ADA Non-Lockable Wall Mount Kit for 6900 Series: Installed on the Cisco Unified IP Phone 6911, 6921, 6941, 6945, and 6961.

This nonlocking wall mount kit meets ADA 4.4.1 requirements.

ADA Non-Lockable Wall Mount Kit for 6900 Series

This section describes how to install the ADA Non-Lockable Wall Mount Kit for 6900 Series on a Cisco Unified IP Phone 6911, 6921, 6941, 6945, and 6961.

The following figure shows the wall mount kit installed on the phone.

Figure F-1 Back View of ADA Non-Lockable Wall Mount Kit Installed on Phone

The following figure shows the phone with the wall mount kit from the side.

Figure F-2 Side View of ADA Non-Lockable Wall Mount Kit Installed on Phone

Components

The following figure shows the contents of the Wall Mount kit.

Figure F-3 Components

The package includes these items:

One phone bracket

One wall bracket

Four #8-18 x 1.25-inch Phillips-head screws with four anchors

Two M2.5 x 6 mm machine screws

One 6-inch Ethernet cable

Before You Begin

You need these tools to install the bracket:

#1 and #2 Phillips-head screwdrivers

Level

Pencil

You must also install an Ethernet jack for the telephone in the desired location if an Ethernet jack does not currently exist. This jack must be wired appropriately for an Ethernet connection. You cannot use a regular telephone jack. For more information about phone installation requirements and warnings, see Setting Up the Cisco Unified IP Phone.

Install Non-Lockable Wall Mount Kit for Phone


Step 1 Mount the wall bracket in the desired location. You can install the bracket over an Ethernet jack, or you can run the Ethernet network cable to a jack nearby.

a. Hold the bracket on the wall, placing it so that the arrow on the back of the bracket is pointing up.

b. Use the level to ensure the bracket is level and use a pencil to mark the screw holes.

c. Use a #2 Phillips-head screwdriver to carefully center the anchor over the pencil mark and press the anchor into the wall.

d. Screw the anchor clockwise into the wall until it is seated flush.

e. Use the included screws and a #2 Phillips-head screwdriver to attach the bracket to the wall.

The following figure shows the steps to mount the wall bracket.

Figure F-4 Mount the Wall Bracket

Step 2 Attach the phone bracket to the IP phone.

a. Detach the handset cord (and headset cord, if there is a headset), power cord, and any other attached cords from the base of the phone.

b. Remove the label covers that are concealing the screw holes.

c. Attach the phone bracket by inserting the tabs into the mounting tabs on the phone. The phone ports should be accessible through the holes in the bracket.

d. Secure the phone bracket to the IP Phone with the machine screws.

e. Thread the handset cord (and headset cord, if using one). Reattach the cords and seat them in the clips incorporated into the phone body.

The following figure shows how to attach the phone bracket.

Figure F-5 Attach Phone Bracket

Step 3 Attach the cables.

a. Attach the Ethernet cable to the 10/100 SW network port and wall jack.

b. (Optional) If you are connecting a network device (such as a computer) to the phone, attach the cable to the 10/100 PC access port.

c. (Optional) If you are using an external power supply, plug the power cord into the phone and dress the cord by clipping it into the clips incorporated into the phone body next to the 10/100 PC port.

The following figure shows the cable attachment.

Figure F-6 Attach Cables

Step 4 Attach the phone to the wall bracket by inserting the tabs on the top of the phone bracket into the slots on the wall bracket.

Use the cable-access openings in the bottom of the bracket to position the power cord and any other cable that does not terminate in the wall behind the bracket. The phone and wall bracket openings together form circular openings with room for one cable per opening.

Step 5 Proceed to Step 3 of Installing the Bracket.


Remove Phone from Non-Lockable Wall Mount

The phone mounting plate contains two tabs to lock the plate into the wall bracket. The following figure shows the location and shape of the tabs.

The following figure shows the tab location.

Figure F-7 Tab Location

To remove the phone and mounting plate from the wall bracket, you must disengage these tabs.

Before You Begin

You require two screwdrivers or metal sticks.


Step 1 Push the screw drivers into the left and right holes in the phone mounting plate approximately 1 in. (2.5 cm).

Step 2 Press firmly inwards (towards the phone) to disengage the tabs, lift up on the phone to release the phone from the wall bracket, and then pull the phone towards you.

The following figure shows how to disengage the tabs.

Figure F-8 Disengage tabs