Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 9.0 (SCCP and SIP)
Cisco Unified IP Phone Wall Mount
Downloads: This chapterpdf (PDF - 1.36MB) The complete bookPDF (PDF - 4.57MB) | The complete bookePub (ePub - 1.1MB) | Feedback

Cisco Unified IP Phone Wall Mount

Cisco Unified IP Phone Wall Mount

This appendix contains information on installing the wall mount for use with the Cisco Unified IP Phone 6901 and 6911 phones.

Wall Mount Components for Cisco Unified IP Phone 6901

The following section describes how to install the Wall Mount plate for use with the Cisco Unified IP Phone 6901.

Cisco recommends that you use the Leviton Wall Mount plate (Leviton type number: 4108W-0SP) for mounting the Cisco Unified IP Phone 6901. The wall mount plate must be ordered separately from the phone.

The following figure and table show a list of items required to mount the Cisco Unified IP Phone 6901 on the wall using the Leviton Wall Mount plate.

Figure 1. Leviton Wall Mount plate



1

RJ45 Connector

2

Leviton Wall Mount Plate

Install Phone on Wall Mount Plate

To install the phone on the wall mount plate, perform these steps:

Procedure
    Step 1   Plug the telephone line cord (RJ45 connector) into the phone jack at the base of the phone.
    Figure 2. RJ45 connector in the phone jack



    1

    Network Port on the Phone

    2

    RJ45 Connector

    Step 2   Plug the RJ45 connector into the wall mount phone jack.
    Figure 3. RJ45 connector in the wall mount jack



    1

    Network Port on the Phone

    3

    Wall Mount Plate

    2

    RJ45 Connector

    4

    Network Port on the Wall Mount Plate

    Step 3   Slip the mounting holes on the base of the wall mount plate and over the wall mount pins.
    Figure 4. Mounting holes



    1

    Mounting Hole on the Phone

    2

    Wall Mount Pin on the Wall Mount Plate

    Step 4   Firmly slide the IP Phone down into place.
    Figure 5. Sliding the IP Phone



    Step 5   Change the handset as described in Adjust Handset Rest.

    Wall Mount Components for Cisco Unified IP Phone 6911

    The following section describes how to install the wall mount for use with the Cisco Unified IP Phone 6911.

    The following figure shows a list of items included in the Wall Mount Kit for the Cisco Unified IP Phone 6911.

    Figure 6. Wall Mount Kit for Cisco Unified IP Phone 6911



    The package includes the following items:

    • One phone bracket
    • One wall bracket
    • Four #10-12x1-inch Phillips-head screws with 4 anchors
    • Two #4-40x1/4-inch machine screws
    • One 6-inch Ethernet cable
    • One key if the bracket includes the optional lock

    Before You Begin

    You need these tools to install the bracket:

    • #1 and #2 Phillips-head screwdrivers
    • Level

    You must also install an Ethernet jack for the telephone in the desired location if an Ethernet jack does not currently exist. This jack must be wired appropriately for an Ethernet connection. You cannot use a regular telephone jack. For more information on phone installation requirements and warnings, see Cisco Unified IP Phone installation.

    Install Bracket

    To install the phone on the wall, perform these steps:

    Procedure
      Step 1   Mount the wall bracket in the desired location. You can install the wall bracket over an Ethernet jack, or you can run the Ethernet network cable to a jack nearby.
      1. Use the level to ensure the wall bracket is level, then use a pencil to mark the screw holes.
      2. Using a #2 Phillips-head screwdriver, carefully center the anchor over the pencil mark and press the anchor into the wall to make markings on the wall.
      3. Screw the anchor clockwise into the wall until it is seated flush.
      4. Use the included screws and a #2 Phillips-head screwdriver to attach the wall bracket to the wall.
        Figure 7. Mounting the Wall Bracket



      Step 2   Attach the phone bracket to the IP Phone.
      1. Detach the handset cord (and headset cord, if there is a headset), power cord, and any other attached cords from the base of the phone.
      2. Remove the label covers that are concealing the screw holes.
      3. Attach the phone bracket by inserting the tabs into the mounting tabs on the phone. The phone ports should be accessible through the holes in the bracket.
      4. Secure the phone bracket to the IP Phone with the Phillips-head screws.
      5. Thread the handset cord (and headset cord, if using one). Reattach the cords and seat them in the clips incorporated into the phone body.
        Figure 8. Attaching the Phone Bracket



      Step 3   Attach the Ethernet cable to the 10/100 SW network port and wall jack.

      If you are connecting a network device (such as a computer) to the phone, attach the cable to the 10/100 PC access port.

      If you are using an external power supply, plug the power cord into the phone and dress the cord by clipping it into the clips incorporated into the phone body next to the 10/100 PC port.

      Figure 9. Attaching the Cables



      Step 4   Attach the phone to the wall bracket by inserting the tabs on the top of the phone bracket into the slots on the wall bracket. Ensure that the power cord and any other cable that does not terminate in the wall behind the bracket are positioned in one of the cable-access openings in the bottom of the bracket. The phone and wall bracket openings together form circular openings with room for one cable per opening.
      Step 5   Use the locking key to lock the phone to the wall bracket.
      Figure 10. Attaching the Phone to the Wall Bracket



      Step 6   Change the handset as described in Adjust Handset Rest.

      Adjust Handset Rest

      With a wall-mounted phone, you might need to adjust the handset rest to ensure that the receiver does not slip out of the cradle. The hook should have a lip on which the handset catches when the phone is vertical. Follow the diagram and steps below to change the hookswitch hook.

      Figure 11. Adjust the Handset Hook



      1

      Remove the handset from the cradle and pull the plastic tab from the handset rest.

      2

      Rotate the tab 180 degrees.

      3

      Hold the tab between two fingers, with the corner notches facing you.

      4

      Line up the tab with the slot in the cradle, and press the tab evenly into the slot. An extension protrudes from the top of the rotated tab. Return the handset to the handset rest.