Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.5 (SCCP and SIP)
Configuring Settings on the Cisco Unified IP Phone
Downloads: This chapterpdf (PDF - 138.0KB) The complete bookPDF (PDF - 5.33MB) | Feedback

Configuring Settings on the Cisco Unified IP Phone

Table Of Contents

Configuring Settings on the Cisco Unified IP Phone

Configuring Settings on the Cisco Unified IP Phone

Phone Settings Options

Accessing the Phone Configuration Settings

Accessing the IVR and Configuring Your Phone Setting


Configuring Settings on the Cisco Unified IP Phone


The Cisco Unified IP Phone includes configurable network settings that you may need to modify before the phone is functional for your users. You can access, view, and change the network settings on the phone by accessing the Interactive Voice Response (IVR). Other configuration settings may be configured in Cisco Unified Communications Manager Administration

This chapter includes the following topics:

Configuring Settings on the Cisco Unified IP Phone

Accessing the Phone Configuration Settings

Configuring Settings on the Cisco Unified IP Phone

Before the Cisco Unified IP Phone can function, you must configure the network setting on the phone. You can review the phone's configuration settings by using the phone's IVR. When the phone is connected to a network with a DHCP server, you can use the DHCP server to configure the network settings. You can also manually configure the phone by accessing the IVR.

Phone Settings Options

Table 4-1 describes the Phone Settings Options that can be configured on the IVR.

Table 4-1 Network Menu Options 

Option
Description

DHCP

Indicates whether the phone has DHCP enabled or disabled.

When DHCP is enabled, the DHCP server assigns the phone an IPaddress, the subnet mask, default router, and TFTP Server. When DHCP is disabled, the administrator must manually assign the IP address, subnet mask, default router, and TFTP server on the phone.

IP Address

Internet Protocol (IP) address of the phone.

If you assign an IP address with this option, you must also assign a subnet mask and default router. See the Subnet Mask and Default Router options in this table.

Subnet Mask

Subnet mask used by the phone.

Default Router 1

Default router used by the phone (Default Router 1).

TFTP Server

Primary Trivial File Transfer Protocol (TFTP) server used by the phone. If you are not using DHCP in your network or you want to change this server, you must assign the TFTP Server.

802.1 xSecurity

Indicates whether the phone has 802.1x security enabled or disabled.


Accessing the Phone Configuration Settings

You can change the PIN of the IVR by navigating to Device > Device Settings > Common Phone Profile, and specifying a password for the Local Phone Unlock Password field in the Common Phone Profile Configuration page.


Note When there is no User ID and/or PIN associated with a phone, the phone uses a default PIN of 24726.


Related Topics

Configuring Settings on the Cisco Unified IP Phone

Accessing the IVR and Configuring Your Phone Setting

To access the IVR and configure your phone settings, follow these steps:


Note You can change the PIN by using the Local Phone Unlock Password in the Common Phone Profile Configuration page of the Cisco Unified CM Administration web page.


Procedure


Step 1 To access the IVR, go off-hook and press the *, #, and 0 buttons simultaneously. Alternatively on the Cisco Unified IP Phone 6911, you can toggle the speaker button and press the *, #, and 0 buttons simultaneously.

The IVR prompts for a password.


Note The Cisco Unified IP Phone 6901 and 6911 allow you to enter only numerical values for password.


Step 2 Enter the PIN by pressing the number keypad, followed by # button.

You are at the IVR main configuration menu.

Step 3 Follow the voice prompts on the IVR. Refer to Table 4-2 for information on navigating the IVR.

Step 4 To return to the main configuration menu, press #.

Step 5 To exit the IVR, end the call.


Table 4-2 describes the various options in the IVR Configuration Menu.

Table 4-2 Navigating the IVR Configuration Menu 

Action
IVR Code
Navigating Notes

Review or Set Network Settings

1

If DHCP is enabled, the IVR announces each network parameter.

If DHCP is disabled, the IVR announces each network parameter, pausing in between to allow you to enter a new value.

1. IVR announces the IP Address. To change the IP address for the phone, use the keypad to enter a new IP address, followed by the #. To retain the current IP address, press #.

2. IVR announces the subnet mask. To change the subnet mask use the keypad to enter a new IP address, followed by the #. To retain the current subnet mask, press #.


Note To enter the dot "." that separates each octet in the IP address, press *.


3. IVR announces the default gateway. To change the default gateway, use the keypad to enter a new IP address, followed by the #. To retain the current default gateway, press #.

Review or Set TFTP Server

2

IVR announces the current TFTP setting.

To change the TFTP server, use the keypad to enter a new IP address, followed by the #. To retain the current TFTP server, press #.

To reset a TFTP server back to the TFTP server set by the DHCP server from a manually configured TFTP server, press *.

Note To enter the dot "." that separates each octet in the IP address, press *.

Enable or Disable DHCP

3

Press 3 to toggle DHCP to enable or disable.

Enable or Disable 802.1X

4

Press 4 to toggle 802.1X to enable or disable security.

Reset to factory settings

0

Note All configuration settings will reset to default factory settings, the and phone will reset. It will take some time for the phone to re-register. Select this option only when needed.