Table Of Contents
Cisco Unified SIP Phone 3951
Release Notes for Firmware Release 8.1(1b)
October 23, 2007
Use these release notes with the Cisco Unified SIP Phone 3951, running firmware release 8.1(1b) which is available only in Asia Pacific and Latin American countries.
Firmware release 8.1(1b) is supported by Cisco Unified Communications Manager releases 6.0 and 5.1.
Note Firmware release 8.1(1b) is designed and tested to interoperate with Cisco call control, most notably Cisco Unified Communications Manager releases 6.0 and 5.1. Although SIP firmware is IETF RFC 3261 compliant, it is not supported by Cisco TAC or Engineering for use with non-Cisco call control systems.
These release notes provide the following information:
Cisco Unified IP Phone Documentation
Refer to publications that are specific to your language, phone model and Cisco Unified Communications Manager release. Navigate from the following documentation URL:
Cisco Unified Communications Manager Documentation
Refer to the Cisco Unified Communications Manager Documentation Guide and other publications specific to your Cisco Unified Communications Manager release. Navigate from the following URL:
Cisco Unified Communications Manager Business Edition Documentation
Refer to the Cisco Unified Communications Manager Business Edition Documentation Guide and other publications that are specific to your Cisco Unified Communications Manager release. Navigate from the following URL:
This section contains these topics:
Shared Line Support
Shared lines are not supported on Cisco Unified SIP Phone 3951. The Cisco Unified SIP Phone 3951 Administration Guide for Cisco Unified Communications Manager 6.0 and 5.1 and Cisco Unified SIP Phone 3951 Phone Guide for Cisco Unified Communications Manager 6.0 and 5.1 erroneously state that shared lines are supported.
DTMF Support on Cisco Unified SIP Phone 3951
Cisco Unified SIP Phone 3951 requires the use of gateways with media termination point (MTP) transcoders that support RFC 2833, such as the Cisco 3825 Router in order to support dual tone multi-frequency (DTMF). You can configure the system to support DTMF by either configuring the MTP on a transcoding device that supports RFC 2833 or by checking the Require DTMF Reception check box for each registered Cisco Unified SIP Phone 3951 in Cisco Unified Communications Manager Administration, Phone Administration window.
This section provides information on supported Cisco Unified Communications Manager versions and device packs.
Supported Cisco Unified Communications Manager Versions
This Cisco Unified SIP Phone 3951 firmware release is supported with Cisco Unified Communications Manager release 6.0 and 5.1.
Cisco Unified Communications Manager Device Packs
You should install these device packs for Cisco Unified Communications Manager 6.0 and 5.1:
For Cisco Unified Communications Manager 5.1
For Cisco Unified Communications Manager 6.0
You can download the device packs from this location on Cisco.com:
This section contains these topics:
Using Bug Toolkit
Known problems (bugs) are graded according to severity level. These release notes contain descriptions of:
•All severity level 1 or 2 bugs.
•Significant severity level 3 bugs.
You can search for problems by using the Cisco Software Bug Toolkit.
To access Bug Toolkit, you need the following items:
•Cisco.com user ID and password
To use the Software Bug Toolkit, follow these steps:
Step 1 To access the Bug Toolkit, go to http://tools.cisco.com/Support/BugToolKit/action.do?hdnAction=searchBugs
Step 2 Log on with your Cisco.com user ID and password.
Step 3 To look for information about a specific problem, enter the bug ID number in the "Search for bug ID" field, then click Go.
There are no open caveats for Cisco Unified SIP Phone 3951 firmware release 8.1(1b).
Table 1 lists Severity 1, 2 and 3 defects that are resolved for the Cisco Unified SIP Phone 3951 firmware release 8.1(1b).
For more information about an individual defect, you can access the online record for the defect by clicking the Identifier or going to the URL shown. You must be a registered Cisco.com user to access this online information.
Because defect status continually changes, be aware that Table 1 reflects a snapshot of the defects that were resolved at the time this report was compiled. For an updated view of resolved defects, access Bug Toolkit as described in the Using Bug Toolkit.
Obtaining Documentation, Obtaining Support, and Security Guidelines
For information on obtaining documentation, obtaining support, providing documentation feedback, security guidelines, and also recommended aliases and general Cisco documents, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
Cisco Product Security Overview
This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html. If you require further assistance please contact us by sending email to email@example.com.
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.
© 2007 Cisco Systems, Inc. All rights reserved.