Cisco Unified Communications Manager Express Command Reference
Cisco Unified CME Commands: T
Downloads: This chapterpdf (PDF - 734.0KB) The complete bookPDF (PDF - 29.95MB) | Feedback

Table of Contents

Cisco Unified CME Commands: T

telephony-service

te lnet-support

tem plate (voice register pool)

tftp-p ath ( voice register global)

t ftp-ser ver-credentials trustpoint

time-format

time-format (voice register global)

t ime out (ephone-hunt)

tim eout (voice hunt-group)

timeouts busy

timeouts interdigit (telephony-service)

timeouts ringing (telephony-service)

ti meouts night-service-bell

ti m eouts transfer-recall

transport (voice register pool-type)

time-webedit (telephony-service)

time-zone

tim ezone ( voice register global)

tr a nsfer-digit-collect

t ran sfer max-length

transfer max-length (voice register pool)

transfer- attended ( voice register template)

transfer- blind ( voice register template)

transfer max-length (voice register pool)

tr ansfer-mode

tran sfer-park blocked

transfer-pattern (telephony-service)

t ran sfer-pattern blocked

transfer-pattern blocked (voice register pool)

t ran sfer-system

transport (voice register pool-type)

t ran slate (ephone-dn)

t ranslate callback-number

translate- outgoing (voice register pool)

tra nsla tion-profile

tra ns lation-profile incoming

tru nk

t ru stpoint (credentials)

t rustp oint-label

type (voice register pool)

ty p e (voice-gateway)

t yp e (voice register dialplan)

type (voice register pool)

Cisco Unified CME Commands: T

Revised: July 25, 2013

This chapter contains commands to configure and maintain Cisco Unified Communications Manager Express (formally known as Cisco Unified CallManager Express). The commands are presented in alphabetical order. Some commands required for configuring Cisco Unified Communications Manager Express (Cisco Unified CME) may be found in other Cisco IOS references. Use the reference master index or search online to find these commands.

telephony-service

To enter telephony-service configuration mode for configuring Cisco Unified CME, use the telephony-service command in global configuration mode. To remove the entire Cisco Unified CME configuration for SCCP IP phones, use the no form of this command.

telephony-service [ setup ]

no telephony-service

 
Syntax Description

setup

(Optional) Interactive setup tool for configuring Cisco Unified IP Phone 7910s, 7940s, and 7960s in Cisco Unified CME.

Note This interactive Cisco CME setup tool is restricted to generating basic configuration files for Cisco Unified IP Phone 7910s, 7940s, and 7960s running SCCP protocol only.

 
Command Default

No Cisco Unified CME configuration for SCCP IP phones is present.

 
Command Modes

Global configuration (config)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.1(5)YD

Cisco ITS 1.0

This command was introduced.

12.2(8)T

Cisco ITS 2.0

This command was integrated into Cisco IOS Release 12.2(8)T.

12.2(15)ZJ

Cisco CME 3.0

The setup keyword was added.

12.3(4)T

Cisco CME 3.0

This command was integrated into Cisco IOS Release 12.3(4)T.

 
Usage Guidelines

This command enters the telephony-service configuration mode for configuring system wide parameters for SCCP IP phones in Cisco Unified CME. The usage of the mode also influences SIP phones in exceptional scenarios (with the usage of service phone under this mode)


Note The voice-gateway system is tied to the telephony service. The telephony-service command must be configured before the voice-gateway system is configured; otherwise, the voice gateway is hidden from the user.


Use the setup keyword to start the interactive setup tool to automatically configure only Cisco Unified IP Phone 7910s, 7940s, and 7960s in Cisco Unified CME.

For alternate methods of automatically configuring Cisco Unified CME, including Cisco Unified IP Phone 7910s, 7940s, and 7960s and other Cisco Unified IP phones, see the Cisco Unified CME Administrator Guide.

The setup keyword is not stored in the router nonvolatile random-access memory (NVRAM).

If you attempt to use the setup option for a system that already has a telephony-service configuration, the command is rejected. To use the setup option after an existing telephony-service configuration has been created, first remove the existing configuration using the no telephony-service command.

Table 73 shows a sample dialog with the Cisco CME setup tool and explains possible responses to the Cisco CME setup tool prompts.

 

Table 73 Cisco CME Setup Tool Dialog Prompts

Cisco CME Setup Tool Prompt
Description

Do you want to setup DHCP service for your IP phones? [yes/no]:

 

If you respond yes, you see the following prompts:

IP network for telephony-service DHCP Pool:

Subnet mask for DHCP network :

TFTP Server IP address (Option 150) :

Default Router for DHCP Pool :

  • Yes—Configures the Cisco Unified CME router to act as a Dynamic Host Configuration Protocol (DHCP) server, automatically providing IP addresses to your IP phones and provisioning the default gateway and TFTP IP addresses to be used by the phones. This method creates a single pool of IP addresses. If you need a pool for non-IP phones or if the Cisco router cannot act as the DHCP router, answer no and manually define the DHCP server.
  • No—Indicates that you have already configured DHCP or static IP addresses for the IP phones.

Do you want to start telephony-service setup? [yes/no]:

  • Yes— Starts the interactive setup tool for configuring Cisco Unified IP Phone 7910s, 7940s, and 7960s.
  • No —Terminates the Cisco CME setup tool.

Enter the IP source address for Cisco CallManager Express:

 

Enter the Skinny Port for Cisco CallManager Express: [2000]:

IP address on which the router provides Cisco Unified CME services, usually the default gateway for the IP subnet that you are using for the IP phones, and the port for Skinny Client Control Protocol (SCCP) messages.

How many IP phones do you want to configure : [0]:

Enter the maximum number of IP phones that this Cisco Unified CME system will support. This number can be increased later, to the maximum allowed for this version and your router.

Note The Cisco CME setup tool associates one number with each newly registering phone. If you want additional numbers on a phone, manually add them later.

Do you want dual-line extensions assigned to phones? [yes for dual-line / no for single-line]:

  • Yes —Each newly registering IP phones is assigned a single number that is associated with a single phone button. The system generates a dual-line ephone-dn entry for each ephone-dn.
  • No —IP phones are linked directly to one or more PSTN trunk lines. Using keyswitch mode requires manual configuration in addition to using the Cisco CME setup tool. The system generates two ephone-dn entries for each ephone-dn, and they are both assigned to a single phone.

What language do you want on IP phones?

0 English

1 French

2 German

3 Russian

4 Spanish

5 Italian

6 Dutch

7 Norwegian

8 Portuguese

9 Danish

10 Swedish

[0]:

Language for IP phone displays, selected from the list.

  • Default is 0, English.

Which Call Progress tone set do you want on IP phones :

0 United States

1 France

2 Germany

3 Russia

4 Spain

5 Italy

6 Netherlands

7 Norway

8 Portugal

9 UK

10 Denmark

11 Switzerland

12 Sweden

13 Austria

14 Canada

[0]:

Locale for the tone set used to indicate call status or progress, selected from the list.

  • Default is 0, United States.

What is the first extension number you want to configure :[0]:

First number in pool of extension numbers to be created for IP phones connected to the Cisco router to be configured.

  • Starting with this number, remaining extension numbers are automatically configured in a contiguous manner.
  • This number must be compatible with your telephone number plan and if you use Direct Inward Dialing (DID) service, with public switched telephone network (PSTN) numbering requirements.

Do you have Direct-Inward-Dial service for all your phones? [yes/no]:

  • Yes—If you have trunk access to public telephone service by ISDN or VoIP for all extension numbers. The system creates an appropriate dial plan.
  • No—If you have simple analog phone lines only (for example, foreign exchange office [FXO] interfaces) or if you have trunk access for some lines but not all lines.

If you answer yes to the previous question, you see the following prompt:

Enter the full E.164 number for the first phone:

Complete ten-digit telephone number, including area code, that corresponds to the first extension number.

Do you want to forward calls to a voice message service? [yes/no]:

  • Yes—To forward calls to a single voice message service number when an IP phone is busy or does not answer. All phone extensions forward their calls to the same voice message service pilot number.
  • No—Not to forward calls to a single voice message service number. Answer no if you do not have a voice message system or if you want to customize call-forwarding behavior for each extension.

If you answer yes to the previous question, you see the following prompt:

Enter the extension or pilot number of the voice message service:

Voice message service pilot number.

  • This step can be ignored during the setup dialog and manually configured later.

Call forward No Answer Timeout: [18]:

Timeout, in seconds, after which to forward calls to voice mail if they are not answered.

  • Default is 18.

Do you wish to change any of the above information? [yes/no]:

  • Yes —Starts the dialog over again without implementing any of the answers that you previously gave.
  • No —Uses specified values to automatically build basic configuration for Cisco Unified IP Phone 7910s, 7940s, and 7960s in Cisco Unified CME.

Examples

The following example shows how to enter telephony-service configuration mode for manually configuring Cisco Unified CME. This example also includes the for configuring the maximum number of phones to 12:

Router(config)# telephony-service

Router(config-telephony)# max-ephones 12

The following example shows how to start the Cisco CME setup tool:

Router(config)# telephony-service setup

telnet-support

To enable Telnet access for the Cisco Unified SIP IP phone, use the telnet-support command in the voice register pool-type mode. To disable Telnet support, use the no form of this command.

telnet-support

no telnet-support

 
Syntax Description,

This command has no arguments or keywords.

 
Command Default

Telnet support is disabled. When the reference-pooltype command is configured, the Telnet support value of the reference phone is ineherited.

 
Command Modes

Voice register pool-type configuration (config-register-pooltype)

 
Command History

Cisco IOS Release
Cisco Product
Modification

15.3(3)M

Cisco Unified CME 10.0

This command was introduced.

 
Usage Guidelines

When you use the no form of this command, the inherited properties of the referenc phone takes precedence over the defulat value.

Examples

The following example shows how to enable Telnet access for the phone model using the telnet-support command:

Router(config)# voice register pool-type 9900

Router(config-register-pool-type)# telnet-support

 
Related Commands

Command
Description

reference-pooltype

Inherits the properties from the nearest reference phone model.

voice register pool-type

Adds a new Cisco Unified SIP IP phone to Cisco Unified CME.

template (voice register pool)

To apply a template to a SIP phone, use the template command in voice register pool configuration mode. To remove the template, use the no form of this command.

template template-tag

no template template-tag

 
Syntax Description

template-tag

The template tag that was created with the voice register template command in voice register global configuration mode. Range is 1 to 5.

 
Command Default

Template is not applied to a SIP IP phone.

 
Command Modes

Voice register pool configuration (config-register-pool)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.4(4)T

Cisco CME 3.4

This command was introduced.

 
Usage Guidelines

Apply any one of five previously defined templates to a SIP phone. Only one template is applied to a SIP phone at one time.

Examples

The following example shows how to define templates 1 and 2 and apply template 1 to SIP phones 1, 2, and 3, and template 2 to SIP phone 4:

Router(config)# voice register template 1

Router(config-register-temp)# anonymous block

Router(config-register-temp)# caller-id block

Router(config-register-temp)# voicemail 5001 timeout 15

 

Router(config)# voice register template 2

Router(config-register-temp)# anonymous block

Router(config-register-temp)# caller-id block

Router(config-register-temp)# no conference

Router(config-register-temp)# no transfer-attended

Router(config-register-temp)# voicemail 5005 timeout 15

 

Router(config)# voice register pool 1

Router(config-register-pool)# template 1

 

Router(config)# voice register pool 2

Router(config-register-pool)# template 1

 

Router(config)# voice register pool 3

Router(config-register-pool)# template 1

 

Router(config)# voice register pool 4

Router(config-register-pool)# template 2

 
Related Commands

Description

voice register template

Enters voice register template configuration mode and defines a template of common parameters for SIP phones.

tftp-path (voice register global)

To specify the directory to which the configuring files for SIP phones in Cisco Unified CME are written, use the tftp-path command in voice register global configuration mode. To return to the default, use the no form of this command.

tftp-path { flash: | slot0: | tftp:// url }

no tftp-path

 
Syntax Description

flash:

Router flash memory.

slot0:

Router slot 0 memory.

tftp://

External TFTP server.

url

URL for external TFTP server.

 
Command Default

The default directory is system memory (system:/cme/sipphone/).

 
Command Modes

Voice register global configuration (config-register-global)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.4(4)T

Cisco CME 3.4

This command was introduced.

 
Usage Guidelines

This command defines the location for configuration files that are generated by using the create profile command.

Examples

The following example shows how to set the path to an HTTP directory for an external TFTP server:

Router(config)# voice register global
Router(config-register-global)# tftp-path tftp://mycompany.com/files/

 
Related Commands

Command
Description

create profile (voice
register global)

Generates the configuration profiles required for SIP phones.

reset (voice register global)

Performs a “hard” reboot similar to a power-off-power-on sequence for all SIP phones in Cisco Unified CME, including contacting the Dynamic Host Configuration Protocol (DHCP) server and the TFTP server for updated information.

tftp-server-credentials trustpoint

To specify the PKI trustpoint that signs the phone configuration files, use the tftp-server-credentials trustpoint command in telephony-service configuration mode. To return to the default, use the no form of this command.

tftp-server-credentials trustpoint label

no tftp-server-credentials trustpoint

 
Syntax Description

label

Name of a configured PKI trustpoint with a valid certificate.

 
Command Default

No trustpoint is defined for TFTP server communications.

 
Command Modes

Telephony-service configuration (config-telephony)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.4(4)XC

Cisco Unified CME 4.0

This command was introduced.

12.4(9)T

Cisco Unified CME 4.0

This command was integrated into Cisco IOS Release 12.4(9)T.

 
Usage Guidelines

This command is used with Cisco Unified CME phone authentication.

Examples

The following example names the CA trustpoint, server12, as the trustpoint that signs the phone configuration files.

Router(config)# telephony-service

Router(config-telephony)# device-security-mode authenticated

Router(config-telephony)# secure-signaling trustpoint server25

Router(config-telephony)# tftp-server-credentials trustpoint server12

Router(config-telephony)# load-cfg-file slot0:Ringlist.xml alias Ringlist.xml sign create

Router(config-telephony)# exit

time-format

To select a 12-hour clock or a 24-hour clock for the time display format on Cisco IP phones in a Cisco CallManager Express (Cisco CME) system, use the time-format command in telephony-service configuration mode. To return to the default, use the no form of this command.

time-format { 12 | 24 }

no time-format

 
Syntax Description

12

Selects a 12-hour clock. This is the default.

24

Selects a 24-hour clock.

 
Command Default

Time is displayed in 12-hour clock format.

 
Command Modes

Telephony-service configuration (config-telephony)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.2(2)XT

Cisco ITS 2.0

This command was introduced.

12.2(8)T

Cisco ITS 2.0

This command was integrated into Cisco IOS Release 12.2(8)T.

Examples

The following example selects a 24-hour clock for the time display on Cisco IP phones:

Router(config)# telephony-service

Router(config-telephony)# time-format 24

 
Related Commands

Description

date-format

Selects a format to display the date on Cisco IP phones.

time-format (voice register global)

To set the time display format on SIP phones in a Cisco CallManager Express (Cisco CME) system, use the time - format command in voice register global configuration mode. To display the time in the default format, use the no form of this command.

time - format { 12 | 24}

no date - format

 
Syntax Description

12

Sets time in a 12-hour (AM/PM) clock.

24

Sets time in a 24-hour clock.

 
Command Default

Time is displayed in 12-hour clock format.

 
Command Modes

Voice register global configuration (config-register-global)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.4(4)T

Cisco CME 3.4

This command was introduced.

Examples

The following example shows how to set the time format to a 24-hour clock so that 11:00PM is displayed as 2300.

Router(config)# voice register global

Router(config-register-global)# time-format 24

 
Related Commands

Description

voice register global

Enters voice register global configuration mode in order to set global parameters for all supported Cisco SIP phones in a Cisco CME or Cisco SIP SRST environment.

timeout (ephone-hunt)

To define the number of seconds after which a call that is not answered is redirected to the next number in a hunt-group list in Cisco Unified CME, use the timeout command in ephone-hunt configuration mode. To return to the default, use the no form of this command.

timeout seconds [ , seconds ...]

no timeout seconds [ , seconds ...]

 
Syntax Description

seconds

Number of seconds. Range: 3 to 60000. You can enter a different value for each hop between ephone-dns in a hunt group. If you enter a single value, the value is applied to each hop between ephone-dns in a hunt group.

 
Command Default

Default is the value of the timeouts ringing which has a default of 180 seconds if it is not set to another value.

 
Command Modes

Ephone-hunt configuration (config-ephone-hunt)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.2(15)ZJ

Cisco CME 3.0

This command was introduced.

12.3(4)T

Cisco CME 3.0

This command was integrated into Cisco IOS Release 12.3(4)T.

12.4(4)XC

Cisco Unified CME 4.0

This command was modified to accept multiple arguments that correspond to the number of ephone-dns configured in the hunt group.

12.4(9)T

Cisco Unified CME 4.0

This command with modifications up was integrated into Cisco IOS Release 12.4(9)T.

 
Usage Guidelines

Use this command to set no-answer timeouts for each hop in a hunt group. You can enter a different value for each hop between ephone-dns in a hunt group or you enter a single value to be applied to each hop between ephone-dns in a hunt group list.

If you configure this command and you also configure the max-timeout for an ephone hunt group, the max-timeout takes precedence over this command.

Examples

The following example defines a no-answer timeout of 10 seconds for each hop between ephone-dns in hunt group 25. If extension 1001 does not answer in 10 seconds, the call is sent to 1002. If 1002 does not answer in 10 seconds, the call is sent to 1003. If 1003 does not answer in 10 seconds, the call is sent to the final number.

ephone-hunt 25 sequential

pilot 4200

list 1001, 1002, 1003

timeout 10

final 4500

The following example shows a hunt-group configuration with separate timeouts, one for each ephone in the hunt-group. If the first extension (1001) does not answer in 7 seconds, the call is sent to the second extension (1002). If the call is not answered by the second extension in 9 seconds, the call is forwarded to the third extension (1003). Extension 1003 has 15 seconds to answer before the call is sent to the final number.

ephone-hunt 3 peer

pilot 4200

list 1001, 1002, 1003

timeout 7, 9, 15

final 4500

The following example shows the configuration for an ephone hunt group for which the max-timeout command is also configured. Using this configuration, if the second number is busy, the third extension, 1003, has only 13 seconds to answer (20 - 7 = 13) because the value for max-timeout is 20 seconds.

ephone-hunt 3 peer

pilot 4200

list 1001, 1002, 1003

timeout 7, 9, 15

max-timeout 20

final 4500

 
Related Commands

Description

final

Defines the last ephone-dn in an ephone hunt group.

hops

Defines the number of times that a call is redirected to the next ephone-dn in a peer ephone-hunt-group list before proceeding to the final ephone-dn.

list

Defines the ephone-dns that participate in an ephone hunt group.

max-redirect

Changes the current number of allowable redirects in a Cisco Unified CME system.

max-timeout

Sets the maximum combined timeout for the no-answer periods for all ephone-dns in an ephone-hunt list,

no-reg (ephone-hunt)

Specifies that the pilot number of an ephone hunt group should not register with the H.323 gatekeeper.

pilot

Defines the ephone-dn that callers dial to reach an ephone hunt group.

preference (ephone-hunt)

Sets preference order for the ephone-dn associated with an ephone-hunt-group pilot number.

timeout (voice hunt-group)

To define the number of seconds after which a call that is not answered is redirected to the next number in a voice hunt-group list, use the timeout command in voice hunt-group configuration mode. To return to the default timeout, use the no form of this command.

timeout seconds

no timeout

 
Syntax Description

seconds

Number of seconds. Range is 3 to 60000. Default is 180.

 
Command Default

Timeout period is 180 seconds.

 
Command Modes

Voice hunt-group configuration (config-voice-hunt-group)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.4(4)T

Cisco CME 3.4

This command was introduced.

 
Usage Guidelines

If Call Forward No Answer is configured for a directory number in the voice hunt group, set the timeout value of this command to a value that is less than the timeout value of the call-forward noan command.

Examples

The following example shows how to define a no-answer timeout of 15 seconds for each hop between phones in peer hunt-group 25:

Router(config)# voice hunt-group 25 peer

Router(config-voice-hunt-group)# timeout 15

 
Related Commands

Command
Description

call-forward noan

Enables call forwarding so that incoming calls to an extension (ephone-dn) that does not answer are forwarded to another number.

final (voice hunt-group)

Defines the last extension in a voice hunt group.

hops (voice hunt-group)

Defines the number of times that a call is redirected to the next directory number in a peer voice hunt-group list before proceeding to the final directory number.

list (voice hunt-group)

Defines the directory numbers that participate in a hunt group.

 

timeouts busy

To set the amount of time after which a call is disconnected from a busy signal, use the timeouts busy command in telephony-service configuration mode. To return to the default value, use the no form of this command.

timeouts busy seconds

no timeouts busy

 
Syntax Description

seconds

Number of seconds after connection before a call is disconnected from a busy signal. Range is from 0 to 30 seconds. Default is 10.

 
Command Default

Timeout busy period is 10 seconds.

 
Command Modes

Telephony-service configuration (config-telephony)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.2(8)T

Cisco ITS 2.0

This command was introduced.

Examples

The following example sets a busy timeout of 10 seconds:

Router(config)# telephony-service

Router(config-telephony)# timeouts busy 10

 
Related Commands

Description

telephony-service

Enters telephony-service configuration mode.

timeouts interdigit (telephony-service)

To set the interdigit timeout value for all Cisco IP phones in a Cisco Unified CME system, use the timeouts interdigit command in telephony-service configuration mode. To return to the default value, use the no form of this command.

timeouts interdigit seconds

no timeouts interdigit

 
Syntax Description

seconds

Interdigit timeout duration for Cisco IP phones, in seconds. Range is from 2 to 120. Default is 10.

 
Command Default

Timeout period is 10 seconds.

 
Command Modes

Telephony-service configuration (config-telephony)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.2(2)XB

Cisco ITS 1.0

This command was introduced.

12.2(8)T

Cisco ITS 2.0

This command was integrated into Cisco IOS Release 12.2(8)T.

 
Usage Guidelines

The interdigit timeout timer is activated when the caller enters a digit and is restarted each time the caller enters subsequent digits until the destination address is identified. This command specifies how long, in seconds, the system waits after a caller enters an initial digit or a subsequent digit of a dialed string. If the configured timeout value is exceeded before the destination address is identified, a tone sounds and the call is terminated. The default is 10 seconds.

To disable the timeouts interdigit timer, set the seconds value to zero.

Examples

The following example sets the interdigit timeout value to 5 seconds for all Cisco IP phones:

Router(config)# telephony-service

Router(config-telephony)# timeouts interdigit 5

In this example, 5 seconds is also the elapsed time after which an incompletely dialed number times out. For example, if you dial nine digits (408555013) instead of the required ten digits (4085550134), you hear a busy tone after 5 “timeout” seconds.

 
Related Commands

Description

timeouts interdigit (voice-port)

Configures the interdigit timeout value for a specified voice port.

timeouts ringing (telephony-service)

To set the timeout value for ringing in a Cisco CallManager Express (Cisco CME) system, use the timeouts ringing command in telephony-service configuration mode. To reset the timeout value to the default value, use the no form of this command.

timeouts ringing seconds

no timeouts ringing

 
Syntax Description

seconds

Duration, in seconds, for which the Cisco CME system allows ringing to continue if a call is not answered. Range is from 5 to 60000. Default is 180.

 
Command Default

Timeout is 180 seconds.

 
Command Modes

Telephony-service configuration (config-telephony)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.2(15)ZJ

Cisco CME 3.0

This command was introduced.

12.3(4)T

Cisco CME 3.0

This command was integrated into Cisco IOS Release 12.3(4)T.

Examples

The following example allows incoming calls to ring for 600 seconds:

Router(config)# telephony-service

Router(config-telephony)# timeouts ringing 600

 
Related Commands

Description

telephony-service

Enters telephony-service configuration mode.

timeouts night-service-bell

To specify the interval between two night-service notification bells, use the timeouts night-service-bell command in telephony-service configuration mode. To reset to the default value, use the no form of this command.

timeouts night-service-bell seconds

no timeouts night-service-bell

 
Syntax Description

seconds

Duration, in seconds, between night-service notification bells. Range: 4 to 30. Default: 12.

 
Command Default

Default is 12 seconds.

 
Command Modes

Telephony-service configuration (config-telephony)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.4(11)XW5

Cisco Unified CME 4.2

This command was introduced.

 
Usage Guidelines

This command modifies the repeat interval between two night-service notification bells for the same call from the default (12 seconds) to the specified number of seconds.

When an ephone-dn is marked for night-service treatment, incoming calls that ring during the night-service time period on that directory number send a notification to all IP phones that are marked to receive night-service bell notification.

Examples

The following partial output shows that the night-service notification bell is configured for 4 seconds between bells for the same call:

Router# show running-configuration

.

.

.

telephony-service

.

.

.

night-service code *1234

night-service day Tue 00:00 23:00

night-service day Wed 01:00 23:59

timeouts night-service-bell 4

!

!

 
Related Commands

Command
Description

night-service bell (ephone)

Marks an IP phone to receive night-service bell notification when incoming calls are received during night-service time periods on ephone-dns that are marked for night service.

night-service bell (ephone-dn)

Marks an ephone-dn to send night-service bell notification to designated IP phones during night-service time periods.

timeouts transfer-recall

To enable Cisco Unified CME to recall a transferred call if the transfer-to party does not answer or is busy, use the timeouts transfer-recall command in ephone-dn, ephone-dn template, or telephony-service configuration mode. To reset to the default value, use the no form of this command.

timeouts transfer-recall seconds

no timeouts transfer-recall

 
Syntax Description

seconds

Duration, in seconds, to wait before recalling a transferred call. Range: 1 to 1800. Default: 0 (disabled).

 
Command Default

Transfer recall is disabled (0 seconds).

 
Command Modes

Ephone-dn (config-ephone-dn)
Ephone-dn template (config-ephone-dn-template)
Telephony-service configuration (config-telephony)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.4(15)XZ

Cisco Unified CME 4.3

This command was introduced.

12.4(20)T

Cisco Unified CME 7.0

This command was integrated into Cisco IOS Release 12.4(20)T.

 
Usage Guidelines

This command enables Call Transfer Recall and sets the number of seconds that Cisco Unified CME waits before sending a transferred call back to the phone that initiated the transfer (transferor).

If the transfer-recall timer set with this command expires before the transfer-to party answers a call, the call is directed back to the transferor and the message, “Transfer Recall From xxxx” displays on the transferor phone. After the first recall, the timer restarts. The maximum number of retries is two if the transfer-to party remains busy or does not answer. The transferor and transfer-to party must be on the same Cisco Unified CME router; the transferee party can be remote.

Transfer recall is not supported if the transfer-to party has Call Forward Busy configured or is a member of any hunt group. If the transfer-to directory number has Call Forward No Answer (CFNA) enabled, Cisco Unified CME recalls a transferred call only if the transfer-recall timeout is less than the timeout set with the call-forward noan command. If the transfer-recall timeout is set to more than the CFNA timeout, the call is forwarded to the CFNA target number if the transfer-to party does not answer.

If the transferor is busy at the time of the recall, Cisco Unified CME attempts the recall again after the retry timer expires. The maximum number of retries is two. If the transferor phone remains busy, the call is disconnected after the third recall attempt.

Use this command in telephony-service configuration mode to enable the transfer-recall timer at the system level for all directory numbers. Use this command in ephone-dn configuration mode to enable the transfer-recall timer for a particular directory number, or use the command in ephone-dn template mode to apply it to one or more directory numbers.

If you use an ephone-dn template to apply a command to a directory number and you also use the same command in ephone-dn configuration mode for the same directory number, the value that you set in ephone-dn configuration mode has priority. This command, set in telephony-service configuration mode, has the lowest priority.

Examples

The following example shows that transfer recall is enabled for extension 1030 (ephone-dn 103), which is assigned to ephone 3. If extension 1030 forwards a call and the transfer-to party does not answer, after 60 seconds the unanswered call is sent back to extension 1030 (transferor).

ephone-dn 103

number 1030

name Smith, John

timeouts transfer-recall 60

!

ephone 3

mac-address 002D.264E.54FA

type 7962

button 1:103

 
Related Commands

Command
Description

call-forward busy

Enables call forwarding so that incoming calls to a busy extension (ephone-dn) are forwarded to another extension.

call-forward noan

Enables call forwarding so that incoming calls to an extension (ephone-dn) that does not answer are forwarded to another number.

transfer-mode

Specifies the call transfer method for an individual directory number.

transfer-system

Specifies the call transfer method globally for all directory numbers.

trunk

Associates an ephone-dn with a foreign exchange office (FXO) port.

transport (voice register pool-type)

To define the default transport type supported by the new Cisco Unified SIP IP phone, use the transport command in voice register pool-type mode. To remove the description, use the no form of this command.

transport { udp | tcp }

no transport { udp | tcp }

 
Syntax Description,

udp

(Optional) Selects UDP as the transport layer protocol. This is the default transport protocol

tcp

(Optional) Selects TCP as the transport layer protocol.

 
Command Default

The default transport protocol is UDP. When the reference-pooltype command is configured, the transport value of the reference phone is inherited.

 
Command Modes

Voice Register Pool-Type Configuration (config-register-pooltype)

 
Command History

Cisco IOS Release
Cisco Product
Modification

15.3(3)M

Cisco Unified CME 10.0

This command was introduced.

 
Usage Guidelines

Use this command to define the default transport type. If this parameter is not configured, UDP is used as default value. Currently, except the Cisco Mobile-iOS and Jabber-Android, all other phone types uses UDP as default transport type. The default transport type will be ignored when the session-transport command is configured for the pool.

Examples

The following example shows how to define the default transport type for a phone model using the transport command:

Router(config)# voice register pool-type 9900

Router(config-register-pool-type)# transport tcp

 
Related Commands

Command
Description

reference-pooltype

Inherits the properties from the nearest reference phone model.

voice register pool-type

Adds a new Cisco Unified SIP IP phone to Cisco Unified CME.

 

time-webedit (telephony-service)

To enable the system administrator to set time on the Cisco Unified CME router through the web interface, use the time-webedit command in telephony-service configuration mode. To disable this feature, use the no form of this command.

time - webedit

no time - webedit

 
Syntax Description

This command has no arguments or keywords.

 
Command Default

Time-setting through the web interface is disabled.

 
Command Modes

Telephony-service configuration (config-telephony)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.2(2)XT

Cisco ITS 2.0

This command was introduced.

12.2(8)T

Cisco ITS 2.0

This command was integrated into Cisco IOS Release 12.2(8)T.

 
Usage Guidelines

The time-webedit allows a local administrator of the Cisco Unified CME router to change and set time through the web-based graphical user interface (GUI).


Note Cisco discourages this method for setting network time. The router should be set up to automatically synchronize its router clock from a network-based clock source using Network Time Protocol (NTP). In the rare case that a network NTP clock source is not available, the time-webedit can be used to allow manual setting and resetting of the router clock through the Cisco CME GUI.


Examples

The following example enables web editing of time:

Router(config)# telephony-service
Router(config-telephony)# time-webedit
 

 
Related Commands

Description

dn - webedit

Enables adding of directory numbers through a web interface.

telephony-service

Enters telephony-service configuration mode.

time-zone

To set the time zone so that the correct local time is displayed on SCCP Cisco Unified IP phones, use the time-zone command in telephony-service configuration mode. To disable a time-zone setting configured with the time-zone command and return to the default time zone (Pacific Standard Time), use the no form of this command.

time-zone number

no time-zone

 
Syntax Description

number

Numeric code for a named time zone. The following are the selections. The numbers in parentheses indicate the offset from Coordinated Universal Time (UTC) in minutes.

Note The time shows incorrectly for phones configured in West Africa during the Summer Time. For West Africa, Summer Time or Daylight Savings Time (DST) is not used. There is no correct time zone in this time zone list to account for this time zone.

  • 1 —Dateline Standard Time (-720)
  • 2 —Samoa Standard Time (-660)
  • 3 —Hawaiian Standard Time (-600)
  • 4 —Alaskan Standard/Daylight Time (-540)
  • 5 —Pacific Standard/Daylight Time (-480)
  • 6 —Mountain Standard/Daylight Time (-420)
  • 7 —United States (US) Mountain Standard Time (-420)
  • 8 —Central Standard/Daylight Time (-360)
  • 9 —Mexico Standard/Daylight Time (-360)
  • 10 —Canada Central Standard Time (-360)
  • 11 —SA Pacific Standard Time (-300)
  • 12 —Eastern Standard/Daylight Time (-300)
  • 13 —US Eastern Standard Time (-300)
  • 14 —Atlantic Standard/Daylight Time (-240)
  • 15 —South America (SA) Western Standard Time (-240)
  • 16 —Newfoundland Standard/Daylight Time (-210)
  • 17 —SA Standard/Daylight Time (-180)
  • 18 —SA Eastern Standard Time (-180)
  • 19 —Mid-Atlantic Standard/Daylight Time (-120)
  • 20 —Azores Standard/Daylight Time (-60)
  • 21 —UTC Standard/Daylight Time (+0)
  • 22 —Greenwich Standard Time (+0)
  • 23 —Western Europe Standard/Daylight Time (+60)
  • 24 —GTB (Athens, Istanbul, Minsk) Standard/Daylight Time (+60)
  • 25 —Egypt Standard/Daylight Time (+60)
  • 26 —Eastern Europe Standard/Daylight Time (+60)

 
Syntax Description

number continued

  • 27 —Romance Standard/Daylight Time (+120)
  • 28 —Central Europe Standard/Daylight Time (+120)
  • 29 —South Africa Standard Time (+120)
  • 30 —Jerusalem Standard/Daylight Time (+120)
  • 31 —Saudi Arabia Standard Time (+180)
  • 32 —Russian Standard/Daylight Time (+180)
  • 33 —Iran Standard/Daylight Time (+210)
  • 34 —Caucasus Standard/Daylight Time (+240)
  • 35 —Arabian Standard Time (+240)
  • 36 —Afghanistan Standard Time (+270)
  • 37 —West Asia Standard Time (+300)
  • 38 —Ekaterinburg Standard Time (+300)
  • 39 —India Standard Time (+330)
  • 40 —Central Asia Standard Time (+360)
  • 41 —Southeast Asia Standard Time (+420)
  • 42 —China Standard/Daylight Time (+480)
  • 43 —Taipei Standard Time (+480)
  • 44 —Tokyo Standard Time (+540)
  • 45 —Central Australia Standard/Daylight Time (+570)
  • 46 —Australia Central Standard Time (+570)
  • 47 —East Australia Standard Time (+600)
  • 48 —Australia Eastern Standard/Daylight Time (+600)
  • 49 —West Pacific Standard Time (+600)
  • 50 —Tasmania Standard/Daylight Time (+600)
  • 51 —Central Pacific Standard Time (+660)
  • 52 —Fiji Standard Time (+720)
  • 53 —New Zealand Standard/Daylight Time (+720)
  • 54—Venezuela Standard Time (-270)
  • 55—Pacific SA Daylight Time (-180)
  • 56—Pacific SA Standard Time (-240)

 
Command Default

The default is time-zone 5, Pacific Standard/Daylight Time (-480).

 
Command Modes

Telephony-service configuration (config-telephony)

 
Command History

Cisco IOS Release
Cisco product
Modification

12.3(11)XL

Cisco CME 3.2.1

This command was introduced.

12.3(14)T

Cisco CME 3.3

This command was integrated into Cisco IOS Release 12.3(14)T.

 
Usage Guidelines

This command works with the vendorConfig section of the Sep*.conf.xml configuration file, which is read by the phone firmware when the Cisco IP Phone is booted up. Certain phones, such as the Cisco Unified IP Phone 7906 , 7911, 7931, 7941, 7942, 7945, 7961, 7962, 7965, 7970 , 7971, and 7975, obtain Coordinated Universal Time (UTC) from the clock of the Cisco router. To display the correct local time, the time display on these phones must be offset by using this command.

This command is not required for Cisco Unified IP Phone 7902G, 7905G, 7912G, 7920, 7921, 7935, 7936, 7940, 7960, or 7985G.

For changes to the time-zone settings take effect, the Sep*.conf.xml file must be updated by using the create cnf-files command and the Cisco IP phones must rebooted by using the reset command.

Examples

The following example sets the Cisco IP Phone 7970 units to Fiji Standard Time:

Router(config)# telephony-service

Router(config-telephony)# time-zone 53

 
Related Commands

Command
Description

create cnf-files

Sets display and phone functionality for the Cisco IP Phone 7970 units using the vendorConfig parameters of the downloaded firmware’s Sep*.conf.xml configuration file.

reset (telephony-service)

Performs a complete reboot of one or all phones associated with a Cisco Unified CME router.

timezone (voice register global)

To set the time zone used for SIP phones in a Cisco Unified CME system, use the timezone command in voice register global configuration mode. To return to the default, use the no form of this command.

timezone number

no timezone

 
Syntax Description

number

Range is 1 to 53. Default is 5, Pacific Standard/Daylight Time

 
Command Default

Default is 5, Pacific Standard/Daylight Time.

 
Command Modes

Voice register global configuration (config-register-global)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.4(4)T

Cisco CME 3.4

This command was introduced.

 
Usage Guidelines

Table 74 lists the supported time zone numbers and the corresponding description.

 

Table 74 Time Zones

Number
Description
Offset in Minutes

1

Dateline Standard Time

-720

2

Samoa Standard Time

-660

3

Hawaiian Standard Time

-600

4

Alaskan Standard/Daylight Time

-540

5

Pacific Standard/Daylight Time

-480

6

Mountain Standard/Daylight Time

-420

7

US Mountain Standard Time

-420

8

Central Standard/Daylight Time

-360

9

Mexico Standard/Daylight Time

-360

10

Canada Central Standard Time

-360

11

SA Pacific Standard Time

-300

12

Eastern Standard/Daylight Time

-300

13

US Eastern Standard Time

-300

14

Atlantic Standard/Daylight Time

-240

15

SA Western Standard Time

-240

16

Newfoundland Standard/Daylight Time

-210

17

South America Standard/Daylight Time

-180

18

SA Eastern Standard Time

-180

19

Mid-Atlantic Standard/Daylight Time

-120

20

Azores Standard/Daylight Time

-60

21

GMT Standard/Daylight Time

+0

22

Greenwich Standard Time

+0

23

W. Europe Standard/Daylight Time

+60

24

GTB Standard/Daylight Time

+60

25

Egypt Standard/Daylight Time

+60

26

E. Europe Standard/Daylight Time

+60

27

Romance Standard/Daylight Time

+120

28

Central Europe Standard/Daylight Time

+120

29

South Africa Standard Time

+120

30

Jerusalem Standard/Daylight Time

+120

31

Saudi Arabia Standard Time

+180

32

Russian Standard/Daylight Time

+180

33

Iran Standard/Daylight Time

+210

34

Caucasus Standard/Daylight Time

+240

35

Arabian Standard Time

+240

36

Afghanistan Standard Time

+270

37

West Asia Standard Time

+300

38

Ekaterinburg Standard Time

+300

39

India Standard Time

+330

40

Central Asia Standard Time

+360

41

SE Asia Standard Time

+420

42

China Standard/Daylight Time

+480

43

Taipei Standard Time

+480

44

Tokyo Standard Time

+540

45

Cen. Australia Standard/Daylight Time

+570

46

AUS Central Standard Time

+570

47

E. Australia Standard Time

+600

48

AUS Eastern Standard/Daylight Time

+600

49

West Pacific Standard Time

+600

50

Tasmania Standard/Daylight Time

+600

51

Central Pacific Standard Time

+660

52

Fiji Standard Time

+720

53

New Zealand Standard/Daylight Time

+720

54

Venezuela Standard Time

-270

55

Pacific SA Daylight Time

-180

56

Pacific SA Standard Time

-240

Examples

The following example shows how top set the time zone to 8, Central Standard Daylight Time:

Router(config)# voice register global

Router(config-register-global)# timezone 8

 
Related Commands

Command
Description

dst (voice register global)

Sets the time period for daylight saving time on SIP phones.

dst auto-adjust (voice register global)

Enables automatic adjustment of daylight saving time on SIP phones.

time-format (voice register global)

Selects a 12-hour clock or a 24-hour clock for the time display format on SIP phones in a Cisco CME system

transfer-digit-collect

To select the digit-collection method for consultative call-transfers, use the transfer-digit-collect command in telephony-service configuration mode for Cisco Unified CME or in call-manager-fallback configuration mode for Cisco Unified SRST. To reset to the default value, use the no form of this command.

transfer - digit-collect { new-call | orig-call }

no transfer-digit-collect

 
Syntax Description

new-call

Dialed digits are collected from new call leg. Default value.

orig-call

Dialed digits are collected from original call leg.

 
Command Default

Digits are collected from the new consultative call-leg ( new-call keyword).

 
Command Modes

Telephony-service configuration (config-telephony)

Call-manager-fallback configuration (config-cm-fallback)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.4(15)XZ

Cisco Unified CME 4.3
Cisco Unified SRST 4.3

This command was introduced.

12.4(20)T

Cisco Unified CME 7.0
Cisco Unified SRST 7.0

This command was integrated into Cisco IOS Release 12.4(20)T.

 
Usage Guidelines

This command specifies whether the dialed digits of the target number are collected on the original call leg or on the new call leg that is created when a phone user initiates a consultative call-transfer.

For consultative transfers, a local number is matched on the number command in ephone-dn configuration mode; a PSTN number is matched on the transfer-pattern command in telephony service mode.

The orig-call keyword selects the method used in versions before Cisco Unified CME 4.3 and Cisco Unified SRST 4.3. After a phone user presses the Transfer soft key, the dialed digits of the target number are collected on the original call leg and buffered until either a local ephone-dn or transfer-pattern is matched. When the transfer-to number is matched, the original call is put on hold and an idle line or channel is seized to send the dialed digits from the buffer.

The new-call keyword selects the default method that is used in Cisco Unified CME 4.3 and later versions and Cisco Unified SRST 4.3 and later versions. The transfer-to digits are collected on a new consultative call-leg that is created when the user presses the Transfer soft key. The consultative call-leg is seized and the dialed digits are passed on without being buffered until the digits are matched and the consultative call-leg moves to the alerting state.

The new-call keyword is supported only if:

  • The transfer-system full-consult command (default) is set in telephony-service configuration mode.
  • The transfer-mode consult command (default) is set for transferor's directory number (ephone-dn).
  • An idle line or channel is available for seizing, digit collection, and dialing.

A consultative transfer is one in which the transferring party either connects the caller to a ringing phone (ringback heard) or speaks with the third party before connecting the caller to the third party.

Examples

The following example shows the digit-collection set to the method used in versions before Cisco Unified CME 4.3 and Cisco Unified SRST 4.3:

Router(config)# telephony-service

Router(config-telephony)# transfer-digit-collect orig-call

 
Related Commands

Command
Description

transfer-mode

Specifies the type of call transfer for an individual directory number that uses the ITU-T H.450.2 standard.

transfer-pattern (telephony-service)

Allows the transfer of calls to phones outside the local Cisco Unified CME network.

transfer - system

Specifies the call transfer method for all IP phones on a Cisco Unified CME router using the ITU-T H.450.2 standard.

 

transfer max-length

To prevent a phone user from dialing more than the specified number of digits when transferring calls, use the transfer max-length command in ephone-template configuration mode. To return to the default, use the no form of this command.

transfer max-length digit-length

no transfer max-length

 
Syntax Description

digit-length

Maximum number of digits that can be dialed when transferring a call. Range is from 3 to 16.

 
Command Default

Phone users can dial a maximum of 16 digits when transferring calls.

 
Command Modes

Ephone-template configuration (config-ephone-template)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.4(4)XC

Cisco Unified CME 4.0

This command was introduced.

12.4(9)T

Cisco Unified CME 4.0

This command was integrated into Cisco IOS Release 12.4(9)T.

 
Usage Guidelines

This command can be used to eliminate toll charges on call transfers by limiting the number of digits that phone users can dial when transferring calls. For example, if you specify a maximum of eight digits, that allows users to dial a single external access digit and a seven-digit local number. In most locations this plan will limit transfers to non-toll destinations. Long-distance calls that typically require ten digits or more will not be allowed.

Examples

The following example limits transfers from ephone 6, extension 2977, to numbers of 8 digits or less.

ephone-template 2

transfer max-length 8

 

ephone-dn 4

number 2977

 

ephone 6

button 1:4

ephone-template 2

 

 

transfer max-length (voice register pool)

To specify the maximum length of the transfer number, use the transfer max-length command in voice register pool or voice register template configuration mode. To disable the maximum length, use the no form of this command.

transfer max-length max-length

no transfer max-length max-length

 
Syntax Description

max-length

Maximum length of the transfer number. Range is 3 to 16.

 
Command Default

No maximum length is specified for the transfer number.

 
Command Modes

Voice register pool configuration (config-register-pool)

Voice register template configuration ((config-register-temp)

 
Command History

Release
Modification

15.3(2)T

This command was introduced.

 
Usage Guidelines

The transfer max-length command is used to indicate the maximum length of the number being dialed for a call transfer. When only a specific number of digits are to be allowed during a call transfer, a value between 3 and 16 is configured.When the number dialed exceeds the maximum length configured, then the call transfer is blocked.

Examples

The following example shows how to configure the maximum length of the transfer number under voice register pool 1. Because the maximum length is configured as 5, only call transfers to Cisco Unified SIP IP phones with a five-digit directory number are allowed. All call transfers to directory numbers with more than five digits are blocked.

Router# configure terminal
Router(config)# voice register pool 1
Router(config-register-pool)# transfer max-length 5
 
 

The following example shows how to configure the maximum length of the transfer number for a set of phones under voice register template 2:

Router# configure terminal
Router(config)# voice register template 2
Router(config-register-temp)# transfer max-length 10
 
 

 

Command
Description

voice register pool

Enters voice register pool configuration mode and creates a pool configuration for a SIP IP phone in Cisco Unified CME or for a set of SIP phones in Cisco Unified SIP SRST

voice register template

Enters voice register template configuration mode and defines a template of common parameters for SIP phones.

transfer-attended (voice register template)

To enable a soft key for attended transfer in a SIP phone template, use the transfer-attended command in voice register template configuration mode. To disable the soft key, use the no form of this command.

transfer-attended

no transfer-attended

 
Syntax Description

This command has no arguments or keywords.

 
Command Default

Soft key is enabled.

 
Command Modes

Voice register template configuration (config-register-temp)

 
Command History

Cisco IOS Release
Cisco product
Modification

12.4(4)T

Cisco CME 3.4

This command was introduced.

 
Usage Guidelines

This command enables a soft key for attended transfer in the specified template which can then be applied to SIP phones in Cisco CME. The attended transfer soft key is enabled by default. To disable the attended transfer soft key, use the no transfer-attended command. To apply the template to a SIP phone, use the template command in voice register pool configuration mode.

A blind transfer is one in which the transferring extension connects the caller to a destination extension before ringback begins. A attended transfer is one in which the transferring party either connects the caller to a ringing phone (ringback heard) or speaks with the third party before connecting the caller to the third party.

Examples

The following example shows how to disable attended transfer in template 1:

Router(config)# voice register template 1

Router(config-register-temp)# no transfer-attended

 
Related Commands

Description

conference (voice register template)

Enables the soft key for conference in a SIP phone template.

template

Applies a template to a SIP phone.

transfer-blind (voice register template)

Enables a soft key for blind transfer in a SIP phone template.

transfer-blind (voice register template)

To enable a soft key for blind transfer in a SIP phone template, use the transfer-blind command in voice register template configuration mode. To disable the soft key, use the no form of this command.

transfer-blind

no transfer-blind

 
Syntax Description

This command has no arguments or keywords.

 
Command Default

Soft key is enabled.

 
Command Modes

Voice register template configuration (config-register-template)

 
Command History

Cisco IOS Release
Version
Modification

12.4(4)T

Cisco CME 3.4

This command was introduced.

 
Usage Guidelines

This command enables a soft key for blind transfer in the specified template which can then be applied to SIP phones in Cisco CME. The blind transfer soft key is enabled by default. To disable the blind transfer soft key, use the no transfer-blind command. To apply the template to a SIP phone, use the template command in voice register pool configuration mode.

A blind transfer is one in which the transferring extension connects the caller to a destination extension before ringback begins. A attended transfer is one in which the transferring party either connects the caller to a ringing phone (ringback heard) or speaks with the third party before connecting the caller to the third party.

Examples

The following example shows how to disable blind transfer in template 1:

Router(config)# voice register template 1

Router(config-register-temp)# no transfer-blind

 
Related Commands

Description

conference (voice register template)

Enables the soft key for conference in a SIP phone template.

template

Applies a template to a SIP phone.

transfer-attended (voice register template)

Enables the soft key for attended transfer on SIP phones.

transfer max-length (voice register pool)

To specify the maximum length of the transfer number, use the transfer max-length command in voice register pool or voice register template configuration mode. To disable the maximum length, use the no form of this command.

transfer max-length max-length

no transfer max-length max-length

 
Syntax Description

max-length

Maximum length of the transfer number. Range is 3 to 16.

 
Command Default

No maximum length is specified for the transfer number.

 
Command Modes

Voice register pool configuration (config-register-pool)

Voice register template configuration ((config-register-temp)

 
Command History

Release
Modification

15.3(2)T

This command was introduced.

 
Usage Guidelines

The transfer max-length command is used to indicate the maximum length of the number being dialed for a call transfer. When only a specific number of digits are to be allowed during a call transfer, a value between 3 and 16 is configured.When the number dialed exceeds the maximum length configured, then the call transfer is blocked.

Examples

The following example shows how to configure the maximum length of the transfer number under voice register pool 1. Because the maximum length is configured as 5, only call transfers to Cisco Unified SIP IP phones with a five-digit directory number are allowed. All call transfers to directory numbers with more than five digits are blocked.

Router# configure terminal
Router(config)# voice register pool 1
Router(config-register-pool)# transfer max-length 5
 
 

The following example shows how to configure the maximum length of the transfer number for a set of phones under voice register template 2:

Router# configure terminal
Router(config)# voice register template 2
Router(config-register-temp)# transfer max-length 10
 
 

 

Command
Description

voice register pool

Enters voice register pool configuration mode and creates a pool configuration for a SIP IP phone in Cisco Unified CME or for a set of SIP phones in Cisco Unified SIP SRST

voice register template

Enters voice register template configuration mode and defines a template of common parameters for SIP phones.

transfer-mode

To specify the type of call transfer for an individual IP phone extension that uses the ITU-T H.450.2 standard, use the transfer-mode command in ephone-dn configuration mode. To remove this specification, use the no form of this command.

transfer - mode { blind | consult }

no transfer-mode

 
Syntax Description

blind

Transfers calls without consultation using a single phone line.

consult

Transfers calls with consultation using a second phone line, if available.

 
Command Default

The ephone-dn uses the transfer-system value that was set systemwide.

 
Command Modes

Ephone-dn configuration (config-ephone)

 
Command History

Cisco IOS Release
Cisco CME Version
Modification

12.2(11)YT

2.1

This command was introduced.

12.2(15)T

2.1

This command was integrated into Cisco IOS Release 12.2(15)T.

 
Usage Guidelines

This command specifies the type of call transfer for an individual Cisco IP phone extension that is using the ITU-T H.450.2 protocol. It allows you to override the system default transfer-system setting (full-consult or full-blind) for that extension.

Call transfers that use H.450.2 can be blind or consultative. A blind transfer is one in which the transferring phone connects the caller to a destination extension before ringback begins. A consultative transfer is one in which the transferring party either connects the caller to a ringing phone (ringback heard) or speaks with the third party before connecting the caller to the third party.

You can specify blind or consultative transfer on a system-wide basis by using the transfer-system command. The system-wide setting can then be overridden for individual phone extensions by using the transfer-mode command. For example, in a Cisco CallManager Express (Cisco CME) network that is set up for consultative transfer, a specific extension with an auto-attendant that automatically transfers incoming calls to specific extension numbers can be set to use blind transfer, because auto-attendants do not use consultative transfer.

Use this command with Cisco IOS Telephony Services V2.1, Cisco CallManager Express 3.0, or a later version.

Examples

The following example sets blind mode for call transfers from this directory number:

Router(config)# ephone-dn 21354

Router(config-ephone-dn)# transfer-mode blind

 
Related Commands

Description

ephone - dn

Enters ephone-dn configuration mode to set directory numbers and parameters for individual Cisco IP phone lines.

transfer - system

Specifies the call transfer method for all IP phones on a Cisco ITS router using the ITU-T H.450.2 standard.

transfer-park blocked

To prevent extensions on an ephone from parking calls, use the transfer-park blocked command in ephone or ephone-template configuration mode. To return to the default, use the no form of this command.

transfer-park blocked

no transfer-park blocked

 
Syntax Description

This command has no arguments or keywords.

 
Command Default

Transfer to park is allowed.

 
Command Modes

Ephone configuration (config-ephone)
Ephone-template configuration (config-ephone-template)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.4(4)XC

Cisco Unified CME 4.0

This command was introduced.

12.4(9)T

Cisco Unified CME 4.0

This command was integrated into Cisco IOS Release 12.4(9)T.

 
Usage Guidelines

This command prevents transfers to park that use the Trnsfer soft key and a call-park slot number, while allowing call-parks that use only the Park soft key. To prevent use of the Park soft key, use an ephone template to remove it from the phone.

An exception to this is made for phones with dedicated park slots. If the transfer-park blocked command is used on an ephone that has a dedicated park slot, the phone is blocked from parking calls at park slots other than the dedicated park slot, but is still able to park calls at its own dedicated park slot. On an IP phone, the user presses the Trnsfer soft key and the call-park feature access code (FAC) to park a call at the phone's dedicated park slot. On an analog phone, the user presses hookflash and the call-park FAC.

When the transfer-park blocked command is used on an ephone that does not have a dedicated park slot, the phone is blocked from parking any calls.

If you use an ephone template to apply a command to a phone and you also use the same command in ephone configuration mode for the same phone, the value that you set in ephone configuration mode has priority.

Examples

The following example prevents ephone 25 and extensions 234, 235, and 236 from parking calls at any call-park slot.

ephone-dn 11

number 234

 

ephone-dn 12

number 235

 

ephone-dn 13

number 236

 

ephone 25

button 1:11 2:12 3:13

transfer-park blocked

 

The following example uses an ephone template to prevent ephone 26 and extension 76589 from parking calls at any call-park slot.

ephone-dn 33

number 76589

 

ephone-template 1

transfer-park blocked

 

ephone 26

button 1:33

ephone-template 1

The following example sets up a dedicated park slot for the extensions on ephone 6 and blocks transfers to call park from extensions 2977, 2978, and 2979 on that phone. Those extensions can still park calls at the phone's dedicated park slot by using the Park soft key or Trnsfer and the call-park FAC.

ephone-dn 3

number 2558

name Park 2977

park-slot reserved-for 2977 timeout 60 limit 3 recall alternate 3754

 

ephone-dn 4

number 2977

 

ephone-dn 5

number 2978

 

ephone-dn 6

number 2979

 

ephone 6

button 1:4 2:5 3:6

transfer-park blocked

transfer-pattern (telephony-service)

To allow transfer of telephone calls from Cisco IP phones to phones other than Cisco IP phones, use the transfer-pattern command in telephony-service configuration mode. To disable these transfers, use the no form of this command.

transfer-pattern transfer-pattern [ blind ]

no transfer-pattern

 
Syntax Description

transfer-pattern

String of digits for permitted call transfers. Wildcards are allowed. A maximum of 32 transfer patterns can be entered, using a separate command for each one.

blind

(Optional) When H.450.2 consultative call transfer is used, this keyword forces transfers that match the pattern to be executed as blind transfers. Overrides settings made using the transfer-system and transfer-mode commands.

 
Command Default

Transfer of calls is enabled only to local Cisco IP phones.

 
Command Modes

Telephony-service configuration (config-telephony)

 
Command History

Cisco IOS Release
Cisco CME Version
Modification

12.1(5)YD

Cisco ITS 1.0

This command was introduced.

12.2(8)T

Cisco ITS 2.0

This command was integrated into Cisco IOS Release 12.2(8)T.

12.2(15)T

Cisco ITS 2.1

The blind keyword was added.

 
Usage Guidelines

This command allows you to transfer calls to “other” phones—that is, to non-IP phones and phones outside of your network. A call is then established between the transferred party and the new recipient. By default, all Cisco IP phone extension numbers are allowed as transfer targets.

The blind keyword is valid only for systems that use Cisco IOS Telephony Services V2.1, Cisco CallManager Express 3.0, or a later version and applies only to consultative transfers made using the H.450.2 standard. The blind keyword forces calls that are transferred to numbers that match the transfer pattern to be executed as blind or full-blind transfers, overriding any settings made using the transfer-system and transfer-mode commands.

When defining transfers to non-local numbers, it is important to note that transfer-pattern digit matching is performed before translation-rule operations. Therefore, you should specify in this command the digits actually entered by phone users before they are translated.

Use of the .T control character for the transfer-pattern argument is not recommended. The .T control character indicates a variable-length dial string, which causes Cisco CME to wait for an interdigit timeout (default is 10 seconds) before transferring a call. To avoid the interdigit timeout, a matching transfer pattern should be used with the transfer-pattern command. For example, use the transfer-pattern 9......... command instead of the transfer-pattern .T command.

Examples

The following example sets a transfer pattern. A maximum of 32 transfer patterns can be entered. In this example, 55501.. (the two periods are wildcards) permits transfers to any number in the range from 555-0100 to 555-0199.

Router(config)# telephony-service

Router(config-telephony)# transfer-pattern 55501..

 
Related Commands

Description

transfer-mode

Specifies the type of call transfer for an individual IP phone extension number that uses the ITU-T H.450.2 standard.

transfer-system

Specifies the call transfer method for all Cisco CME extensions that use the ITU-T H.450.2 standard.

transfer-pattern blocked

To prevent extensions on an ephone from transferring calls to patterns defined using the transfer-pattern (telephony-service) command, use the transfer-pattern blocked command in ephone or ephone-template configuration mode. To return to the default, use the no form of this command.

transfer-pattern blocked

no transfer-pattern blocked

 
Syntax Description

This command has no arguments or keywords.

 
Command Default

Call transfer is allowed to patterns specified in the transfer-pattern (telephony-service) command.

 
Command Modes

Ephone configuration (config-ephone)
Ephone-template configuration (config-ephone-template)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.4(4)XC

Cisco Unified CME 4.0

This command was introduced.

12.4(9)T

Cisco Unified CME 4.0

This command was integrated into Cisco IOS Release 12.4.(9)T.

 
Usage Guidelines

By default, transfers to all numbers except for those on local ephones are automatically blocked. During configuration, you can allow transfers to non-local numbers using the transfer-pattern (telephony-service) command.

Use the transfer-pattern blocked command to prevent individual phones from transferring calls to non-local numbers that have been globally enabled for transfer.

If you use an ephone template to apply a command to a phone and you also use the same command in ephone configuration mode for the same phone, the value that you set in ephone configuration mode has priority.

Examples

The following example blocks transfers from ephone 6 (extension 2977) to the PSTN.

ephone-dn 4

number 2977

 

ephone 6

button 1:4

transfer-pattern blocked

The following example uses an ephone template to block transfers from ephone 6 (extension 2977) and ephone 7 (extension 2978) to the PSTN.

ephone-template 2

transfer-pattern blocked

 

ephone-dn 4

number 2977

ephone-dn 5

number 2978

 

ephone 6

button 1:4

ephone-template 2

 

ephone 7

button 1:5

ephone-template 2

 
Related Commands

Description

ephone-template (ephone)

Applies template to an ephone.

transfer-pattern (telephony service)

Allows call transfers to numbers outside the Cisco Unified CME system.

transfer-pattern blocked (voice register pool)

To block all call transfers for a specific Cisco Unified SIP IP phone or a set of Cisco Unified SIP IP phone, use the transfer-pattern blocked command in voice register pool and voice register template configuration mode. To allow call transfers, use the no form of this command.

transfer-pattern blocked

no transfer-pattern blocked

 
Syntax Description

This command has no arguments or keywords.

 
Command Default

Call transfers for a specific Cisco Unified SIP IP phone or a set of Cisco Unified SIP IP phone are allowed.

 
Command Modes

Voice register pool configuration (config-register-pool)

Voice register template configuration ((config-register-temp)

 
Command History

Release
Modification

15.3(2)T

This command was introduced.

 
Usage Guidelines

When the transfer-pattern blocked command is configured for a specific phone, no call transfers are allowed from that phone over the trunk.

This feature forces unconditional blocking of all call transfers from a specific phone to any other non-local numbers (external calls from one trunk to another trunk). No call transfers from this specific phone are possible even when a transfer pattern matches the dialed digits for transfer.

Examples

The following example shows how to block all call transfers for voice register pool 5:

Router(config)# voice register pool 5
Router(config-register-pool)# transfer-pattern ?
blocked global transfer pattern not allowed
Router(config-register-pool)# transfer-pattern blocked
 
 

The following example shows how to block all call transfers for a set of Cisco Unified SIP IP phones defined by voice register template 9:

Router(config)# voice register template 9
Router(config-register-temp)# transfer-pattern ?
blocked global transfer pattern not allowed
Router(config-register-temp)# transfer-pattern blocked
 

 
Related Commands

Command
Description

voice register pool

Enters voice register pool configuration mode and creates a pool configuration for a Cisco Unified SIP IP phone in Cisco Unified CME or for a set of Cisco Unified SIP IP phones in Cisco Unified SIP SRST.

voice register template

Enters voice register template configuration mode and defines a template of common parameters for Cisco Unified SIP IP phones.

transfer-system

To specify the call transfer method to be used by Cisco Unified IP phones in Cisco Unified CME, use the transfer-system command in telephony-service configuration mode. To disable the call transfer method, use the no form of this command.

transfer-system { blind | full-blind | full-consult [ dss ] | local-consult }

no transfer-system

 
Syntax Description

blind

Transfers calls without consultation using a single phone line and the Cisco proprietary method. This is the default for Cisco CME 3.4 and earlier versions.

full-blind

Transfers calls without consultation using H.450.2 standard methods.

full-consult

Transfers calls using H.450.2 with consultation using a second phone line, if available. The calls fall back to full-blind if a second line is not available. This is the default for Cisco Unified CME 4.0 and later versions.

dss

Transfers calls with consultation to idle monitor lines. All other call-transfer behavior is identical to full-consult.

local-consult

Transfers calls with local consultation using a second phone line, if available, or the calls fall back to blind if the target for consultation or transfer is not local. This mode is intended for use primarily in Voice over Frame Relay (VoFR) networks, because the Cisco VoFR call transfer protocol does not support an end-to-end transfer-with-consultation mechanism. Not supported if transfer-to destination is on the Cisco ATA, Cisco VG224, or a SCCP-controlled FXS port.

 
Command Default

For Cisco Unified CME 4.0 and later versions, the transfer mode is full-consult .
For Cisco CME 3.4 and earlier versions, the transfer mode is blind .

 
Command Modes

Telephony-service configuration (config-telephony)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.2(11)YT

Cisco ITS 2.1

This command was introduced.

12.2(15)T

Cisco ITS 2.1

This command was integrated into Cisco IOS Release 12.2(15)T.

12.3(11)T

Cisco CME 3.2

The dss keyword was introduced.

12.4(4)XC

Cisco Unified CME 4.0

The command default was changed from blind to full-consult .

12.4(9)T

Cisco Unified CME 4.0

This command with the default of full-consult was integrated into Cisco IOS Release 12.4(9)T.

 
Usage Guidelines

Direct station select is a functionality that allows a multibutton phone user to transfer calls to an idle monitor line by pressing the Transfer key and the appropriate monitor button. The dss keyword permits consultative call transfer to monitored lines.

Call transfers can be blind or consultative. A blind transfer is one in which the transferring extension connects the caller to a destination extension before ringback begins. A consultative transfer is one in which the transferring party either connects the caller to a ringing phone (ringback heard) or speaks with the third party before connecting the caller to the third party.

The transfer-system command specifies whether the H.450.2 standard or a Cisco proprietary method will be used to communicate call transfer information across the network. When you specify use of the H.450.2 consultative or blind mode of transfer globally by using the transfer-system command (or by using the default), you can override this mode for individual ephones by using the transfer-mode command. For example, in a system that is set up for consultative transfer, a specific extension with an auto-attendant that automatically transfers incoming calls to specific extension numbers can be set to use blind transfer, because auto-attendants do not use consultative transfer.

Prior to Cisco Unified CME 4.0, the default for this command specified the Cisco proprietary method. In Cisco Unified CME 4.0, the default was changed to specify the H.450.2 standard as the transfer method. Consult Table 75 for configuration recommendations for different versions of Cisco Unified CME.

 

Table 75 Transfer Method Recommendations

Cisco Product
transfer-system Default
transfer-system to Use
Transfer Method Recommendation

Cisco Unified CME 4.0 and later versions

full-consult

full-consult
or
full-blind

Use H.450.2 for call transfer. Because this is the default for this version, you do not need to use the transfer-system command unless you want to use the full-blind or dss keyword.

Optionally, you can use the proprietary Cisco method by using the transfer-system command with the blind or local-consult keyword.

Cisco CME 3.0 to 3.3

blind

full-consult
or
full-blind

Use H.450.2 for call transfer. You must explicitly configure the transfer-system command with the full-consult or full-blind keyword because H.450.2 is not the default for this version.

Optionally, you can use the proprietary Cisco method by using the transfer-system command with the blind or local-consult keyword.

Cisco ITS 2.1 to 3.0

blind

blind
or
local-consult

Use the Cisco proprietary method. Because this is the default for this version, you do not need to use the transfer-system command unless you want to use the local-consult keyword.

Optionally, you can use the H.450.2 standard for call transfer by using transfer-system command with the full-consult or full-blind keyword. You must also configure the router with a Tcl script that is contained in the file called app-h450-transfer.x.x.x.x.zip. This file is posted on the Cisco Unified CME software download website at http://www.cisco.com/cgi-bin/tablebuild.pl/ip-iostsp .

Examples

The following example sets full consultation as the call transfer method:

Router(config)# telephony-service

Router(config-telephony)# transfer-system full-consult

 
Related Commands

Description

transfer-mode

Specifies the type of call transfer for an individual IP phone extension that uses the H.450.2 standard.

transport (voice register pool-type)

To define the default transport type supported by thenew phone, use the transport command in voice register pool-type mode. To remove the description, use the no form of this command.

transport { udp | tcp }

no transport { udp | tcp }

 
Syntax Description,

udp

(Optional) Selects UDP as the transport layer protocol. This is the default transport protocol

tcp

(Optional) Selects TCP as the transport layer protocol.

 
Command Default

The default transport protocol is UDP. When the reference-pooltype command is configured, the transport value of the reference phone is ineherited.

 
Command Modes

Voice Register Pool-Type Configuration (config-register-pooltype)

 
Command History

Cisco IOS Release
Cisco Product
Modification

15.3(3)M

Cisco Unified CME 10.0

This command was introduced.

 
Usage Guidelines

Use this command to define the default transport type. If this parameter is not configured, UDP is used as default value. Currently, except the Cisco Mobile-iOS and Jabber-Android, all other phone types uses UDP as default transport type. The default transport type will be ignored when the session-transport command is configured for the pool.

Examples

The following example shows how to define the default transport type for a phone model using the transport command:

Router(config)# voice register pool-type 9900

Router(config-register-pool-type)# transport tcp

 
Related CommandsC

Command
Description

voice register pool-type

Adds a new Cisco Unified SIP IP phone to Cisco Unified CME.

translate (ephone-dn)

To apply a translation rule in order to manipulate the digits that are dialed by users of Cisco Unified IP phones, use the translate command in ephone-dn or ephone-dn-template configuration mode. To disable the translation rule, use the no form of this command.

translate { called | calling } translation - rule - tag

no translate { called | calling }

 
Syntax Description

called

Translate the called number.

calling

Translate the calling number.

translation - rule - tag

Unique sequence number by which the rule set is referenced. This number is arbitrarily chosen. Range is from 1 to 2147483647. There is no default value.

 
Command Default

No translation rule is applied.

 
Command Modes

Ephone-dn configuration (config-ephone-dn)
Ephone-dn-template configuration (config-ephone-template-dn)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.2(2)XT

Cisco ITS 2.0

This command was introduced.

12.2(8)T

Cisco ITS 2.0

This command was integrated into Cisco IOS Release 12.2(8)T.

12.4(4)XC

Cisco Unified CME 4.0

This command was made available in ephone-dn-template configuration mode.

12.4(9)T

Cisco Unified CME 4.0

This command in ephone-dn-template configuration mode was integrated into Cisco IOS Release 12.4(9)T.

 
Usage Guidelines

This command allows you to select a preconfigured translation rule to modify the number dialed by a specific extension (Cisco Unified IP phone destination number, or ephone-dn). A translation rule is a general-purpose digit-manipulation mechanism that performs operations such as automatically adding telephone area and prefix codes to dialed numbers. The translation rules are applied to the voice ports created by the ephone-dn. The called keyword translates the called number, and the calling keyword translates the calling number.

The translation rule mechanism inserts a delay into the dialing process when digits are entered that do not explicitly match any of the defined translation rules. This delay is set by the interdigit timeout. The translation-rule mechanism uses the delay to ensure that it has acquired all of the digits from the phone user before making a final decision that there is no translation-rule match available (and therefore no translation operation to perform). To avoid this delay, it is recommended that you include a dummy translation rule to act as a pass-through rule for digit strings that do not require translation. For example, a rule like “^5 5” that maps a leading 5 digit into a 5 would be used to prevent the translation rule delay being applied to local extension numbers that started with a 5.


Note For this command to take effect, appropriate translation rules must have been created at the VoIP configuration level. Use the show voice translation-rule command to view the translation rules that you have defined. For in formation, see the Dial Peer Configuration on Voice Gateway Routers.


If you use an ephone-dn template to apply a command to an ephone-dn and you also use the same command in ephone-dn configuration mode for the same ephone-dn, the value that you set in ephone-dn configuration mode has priority.

Examples

The following example applies translation rule 20 to numbers called by extension 46839:

Router(config)# translation-rule 20

Router(config-translate)# rule 0 1234 2345 abbreviated

Router(config-translate)# exit

Router(config)# ephone-dn 1

Router(config-ephone-dn)# number 46839

Router(config-ephone-dn)# translate called 20

The following example uses an ephone-dn-template to apply translation rule 20 to numbers called by extension 46839:

Router(config)# translation-rule 20

Router(config-translate)# rule 0 1234 2345 abbreviated

Router(config-translate)# exit

Router(config)# ephone-dn-template 1

Router(config-ephone-dn-template)# translate called 20

Router(config-ephone-dn-template)# exit

Router(config)# ephone-dn 1

Router(config-ephone-dn)# number 46839

Router(config-ephone-dn)# ephone-dn-template 1

 
Related Commands

Description

rule

Defines a translation rule.

translation - rule

Creates a translation identifier and enters translation-rule configuration mode.

translate callback-number

To assign a translation profile for incoming or outgoing call legs on a Cisco IP phone, use the translation-profile command in call-manager-fallback configuration mode. To delete the translation profile from the voice port, use the no form of this command.

translate callback-number

no translate callblack-number

 
Syntax Description

incoming

Specifies that this translation profile handles incoming calls.

outgoing

Specifies that this translation profile handles outgoing calls.

name

Name of the translation profile.

 
Command Default

No default behavior or values.

 
Command Modes

Voice translation-profile configuration (cfg-translation-profile)

 
Command History

Cisco IOS Release
Cisco Product
Modification

15.1(3)T

Cisco Unified CME 8.5

This command was introduced.

 
Usage Guidelines

Use the tranlsate callback-number command to translate a called number to E.164 format. The translated number allows a called or calling number to be presented in its local form. The translate callback-number command is applied when translation-profile is configured on dialpeers, ephone-dn, and voice register-dn. The translate callback-number command is effective when the configruation setup reached the SCCP and SIP IP phones.

Examples

The following example shows a configuration in which a translation profile called name1 is created with two voice translation rules. Rule1 consists of associated calling numbers, and rule2 consists of redirected called numbers. The Cisco IP phones in SRST mode are configured with name1.

voice translation-profile name1
translation calling rule1
translation called-direct rule2
 
call-manager-fallback
translation-profile incoming name1

 
Related Commands

Command
Description

show voice translation-profile

Displays the configuration of a translation profile.

translate (call-manager- fallback)

Applies a translation rule to modify the phone number dialed or received by any Cisco IP phone user during CallManager fallback.

translation-rule

Creates a translation name and enters translation-rule configuration mode to apply rules to the translation name.

voice translation-profile

Defines a translation profile for voice calls.

translate-outgoing (voice register pool)

To allow an explicit setting of translation rules on the VoIP dial peer in order to modify a phone number dialed by any Cisco IP phone user, use the translate-outgoing command in voice register pool configuration mode. To disable translation rules, use the no form of this command.

translate-outgoing { called | calling } rule-tag

no translate-outgoing { called | calling }

 
Syntax Description

called

Called party requires translation.

calling

Calling party requires translation.

rule-tag

The rule-tag is an arbitrarily chosen number by which the rule set is

referenced. The range is from 1 to 2147483.

 
Command Default

Translation rules are enabled on the VoIP dial peer.

 
Command Modes

Voice register pool configuration (config-register-pool)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.2(15)ZJ

Cisco SIP SRST 3.0

This command was introduced.

12.3(4)T

Cisco SIP SRST 3.0

This command was integrated into Cisco IOS Release 12.3(4)T.

12.4(4)T

Cisco CME 3.4
Cisco SIP SRST 3.4

This command was added to Cisco CME.

 
Usage Guidelines

Translation rules are a powerful general-purpose number-manipulation mechanism that perform operations such as automatically adding telephone area and prefix codes to dialed numbers. The translation rules are applied to VoIP dial peers created by Cisco Unified Session Initiation Protocol (SIP) Survivable Remote Site Telephony (SRST) or Cisco Unified CallManager Express (Cisco Unified CME).

During registration, a dial peer is created, and that dial peer includes a default translation rule. The translate-outgoing command allows you to change the translation rule, if desired. The translate-outgoing command allows you to select a preconfigured number translation rule to modify the number dialed by a specific extension.


Note Translation rules must be set by using the translate-outgoing command before the alias command is configured in Cisco Unified SIP SRST.

Configure the id (voice register pool) command before any other voice register pool commands, including the translate-outgoing command. The id command identifies a locally available individual SIP phone or set of SIP phones.


 

Examples

Cisco Unified CME

The following is partial sample output from the show running-config command showing that called-party 1 requires translation.

voice register pool 1

id mac 0030.94C2.A22A

preference 5

cor incoming call91 1 91011

translate-outgoing called 1

Cisco Unified SIP SRST

The following is partial sample output from the show running-config command showing that called-party 1 requires translation.

voice register pool 1

id mac 0030.94C2.A22A

preference 5

cor incoming call91 1 91011

translate-outgoing called 1

proxy 10.2.161.187 preference 1 monitor probe icmp-ping

alias 1 94... to 91011 preference 8

voice-class codec 1

 
Related Commands

Description

alias (voice register pool)

Allows Cisco SIP IP phones to handle inbound PSTN calls to telephone numbers that are unavailable when the main proxy is not available.

id (voice register pool)

Explicitly identifies a locally available individual Cisco SIP IP phone, or when running Cisco Unified SIP SRST, set of Cisco SIP IP phones.

translate-outgoing (dial-peer)

Applies a translation rule to manipulate dialed digits on an outbound POTS or VoIP call leg.

voice register pool

Enters voice register pool configuration mode for SIP phones.

translation-profile

To assign a translation profile for incoming or outgoing call legs on a Cisco Unified IP phone, use the translation-profile command in ephone-dn or ephone-dn-template configuration mode. To delete the translation profile from the voice port, use the no form of this command.

translation-profile { incoming | outgoing } name

no translation-profile { incoming | outgoing } name

 
Syntax Description

incoming

Specifies that this translation profile handles incoming calls.

outgoing

Specifies that this translation profile handles outgoing calls.

name

Name of the translation profile.

 
Command Default

No default behavior or values

 
Command Modes

Ephone-dn configuration (config-ephone-dn)
Ephone-dn-template configuration (config-ephone-dn-template)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.3(11)T

Cisco CME 3.2

This command was introduced.

12.4(4)XC

Cisco Unified CME 4.0

This command was made available in ephone-dn-template configuration mode.

12.4(9)T

Cisco Unified CME 4.0

This command in ephone-dn-template configuration mode was integrated into Cisco IOS Release 12.4(9)T.

 
Usage Guidelines

Use the translation-profile command to assign a global predefined translation profile to an incoming or outgoing call leg.

If you use an ephone-dn template to apply a command to an ephone-dn and you also use the same command in ephone-dn configuration mode for the same ephone-dn, the value that you set in ephone-dn configuration mode has priority.

Examples

The following example assigns the translation profile named call_in to handle translation of incoming calls and a translation profile named call_out to handle outgoing calls:

Router(config)# ephone-dn 1

Router(config-ephone-dn)# number 2555

Router(config-ephone-dn)# translation-profile incoming call_in

Router(config-ephone-dn)# translation-profile outgoing call_out

The following example uses an ephone-dn-template to assign the translation profile named call_in to handle translation of incoming calls and the translation profile named call_out to handle outgoing calls:

Router(config)# ephone-dn-template 10

Router(config-ephone-dn-template)# translation-profile incoming call_in

Router(config-ephone-dn-template)# translation-profile outgoing call_out

Router(config-ephone-dn-template)# exit

Router(config)# ephone-dn 1

Router(config-ephone-dn)# number 2555

Router(config-ephone-dn)# ephone-dn-template 10

 
Related Commands

Description

s how voice translation-profile

Displays the configuration of a translation profile.

translate

Applies a translation rule to modify the phone number dialed or received by any Cisco Unified IP phone user.

translation-rule

Creates a translation name and enters translation-rule configuration mode.

voice translation-profile

Defines a translation profile for voice calls.

voice translation-rule

Defines a translation rule for voice calls.

translation-profile incoming

To assign a translation profile for incoming call legs on a SIP phone, use the translation-profile incoming command in voice-register-dn configuration mode. To delete the translation profile from the directory number, use the no form of this command.

translation-profile incoming name

no translation-profile incoming

 
Syntax Description

name

Name of the translation profile to apply to incoming calls to this directory number. This is the name argument that was created for the profile with the voice translation-profile command.

 
Command Default

No translation profile is assigned to the directory number.

 
Command Modes

Voice register dn configuration (config-register-dn)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.4(11)XJ

Cisco Unified CME 4.1

This command was introduced.

12.4(15)T

Cisco Unified CME 4.1

This command was integrated into Cisco IOS Release 12.4(15)T.

 
Usage Guidelines

Use this command to assign a predefined translation profile to incoming call legs on the specified directory number. The translation profile that you assign is created by using the voice translation-profile command.

Examples

The following example shows that the translation profile named call_in is assigned to handle translation of incoming calls to directory number 1:

Router(config)# voice register dn 1

Router(config-register-dn)# number 2555

Router(config-register-dn)# translation-profile incoming call_in

 
Related Commands

Description

s how voice translation-profile

Displays the configuration of a translation profile.

translate (translation profiles)

Associates a translation rule with a voice translation profile.

voice translation-profile

Defines a translation profile for voice calls.

voice translation-rule

Defines a translation rule for voice calls.

trunk

To associate an ephone-dn with a foreign exchange office (FXO) port, use the trunk command in ephone-dn configuration mode. To disassociate the ephone-dn from the trunk number, use the no form of this command.

trunk digit - string [ timeout seconds ] [ transfer-timeout seconds ] [ monitor-port port ]

no trunk

 
Syntax Description

digit-string

The number of the trunk line.

timeout seconds

(Optional) Interdigit timeout between dialed digits, in seconds. Range is 3 to 30. Default is 3.

transfer-timeout seconds

(Optional) Number of seconds that Cisco Unified CME waits for the transfer-to party to answer a call after which the call is recalled to the phone that initiated the transfer. This keyword is supported for dual-line ephone-dns only. Range is 5 to 60000. Default is disabled.

monitor-port port

(Optional) Enables a button lamp or icon that shows that the specified port is in use. Port argument is platform-dependent; type ? to display syntax.

 
Command Default

Ephone-dns are not associated with FXO ports.

 
Command Modes

Ephone-dn configuration (config-ephone)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.3(11)T

Cisco CME 3.2

This command was introduced.

12.4(4)XC

Cisco Unified CME 4.0

The monitor-port and transfer-timeout keywords were added and support for dual-line ephone-dns was added.

12.4(9)T

Cisco Unified CME 4.0

This command with modifications was integrated into Cisco IOS Release 12.4(9)T.

 
Usage Guidelines

Use this command to configure ephone-dns to support FXO lines that allow phones to have private lines connected directly to the PSTN. To bind the ephone-dn to the FXO port, use the destination pattern configured for the FXO line’s POTS dial peer for the digit-string argument.

The timeout seconds argument controls the interdigit delay period, during which digits are collected from the user, and the delay before the connection to the FXO port is established. The argument controls the amount of time that Cisco Unified CME waits to collect digits for the dialed number, so that the digits can be included in the redial buffer and the Placed Calls directory of the phone. Digits that are entered after the timeout period are not included in the redial buffer or in the Placed Calls directory on the phone. The timeout parameter does not affect the time used to cut through the connection from the phone’s trunk button to the FXO port. The phone user must either enter the pound (#) key or wait for this interdigit timeout to complete digit collection.

The phone user also has the option to use the phone’s on-hook dialing feature so that the phone itself performs complete dial-string digit collection before signaling off-hook to the Cisco Unified CME. In this case all digits will be included in the Redial and Placed Calls Directory.

The monitor-port keyword enables direct status monitoring of the FXO port on the line button of the IP phone. The line button indicator, either a lamp or an icon depending on the phone, shows the in-use status of the FXO port during the duration of the call.

The transfer-timeout argument enables a transferred call to be automatically recalled if the transfer target does not answer after the specified number of seconds. The call is withdrawn from the transfer-to phone and the call resumes ringing on the phone that initiated the transfer.

The monitor-port and transfer-timeout keywords are not supported on ephone-dns for analog ports on the Cisco VG 224.

For dual-line ephone-dns, the second channel cannot receive incoming calls when the trunk command is configured.

Examples

The following example shows the configuration for two phones that each have a private FXO line button and a shared-line button.

The shared line’s voice ports and dial peers are as follows:

Router(config)# voice-port 1/0/1

Router(config-voice-port)# connection plar-opx 1000

 

Router(config)# dial-peer voice 101 pots

Router(config-dial-peer)# destination-pattern 9

Router(config-dial-peer)# port 1/0/1

 

The private lines’ voice ports and dial peers are as follows:

Router(config)# voice-port 1/1/0

Router(config-voice-port)# connection plar-opx 5550111

 

Router(config)# dial-peer voice 110 pots

Router(config-dial-peer)# destination-pattern 80

Router(config-dial-peer)# port 1/1/0

 

Router(config)# voice-port 1/1/1

Router(config-voice-port)# connection plar-opx 5550112

 

Router(config)# dial-peer voice 111 pots

Router(config-dial-peer)# destination-pattern 81

Router(config-dial-peer)# port 1/1/1

 

The following is the configuration for the shared and private ephone-dns:

Router(config)# ephone-dn 1

Router(config-ephone-dn)# number 1000

Router(config-ephone-dn)# name Line1

Router(config-ephone-dn)# no huntstop

 

Router(config)# ephone-dn 2

Router(config-ephone-dn)# number 5550111

Router(config-ephone-dn)# name Private line

Router(config-ephone-dn)# trunk 80

 

Router(config)# ephone-dn 3

Router(config-ephone-dn)# number 5550112

Router(config-ephone-dn)# name Private line

Router(config-ephone-dn)# trunk 81

The following is the configuration for ephones with button 1 as a shared line and button 2 a private line:

Router(config)# ephone 1

Router(config-ephone)# mac-address 1111.1111.1101

Router(config-ephone)# button 1:1 2:2

 

Router(config)# ephone 2

Router(config-ephone)# mac-address 1111.1111.1102

Router(config-ephone)# button 1:1 2:3

The following example shows that transferred calls are recalled after 30 seconds if the destination party does not answer and status monitoring is enabled for FXO port 1/1/1.

Router(config)# ephone-dn 5

Router(config-ephone-dn)# trunk 801 timeout 5 transfer-timeout 30 monitor-port 1/1/1

 
Related Commands

Description

destination-number

Specifies a connection mode for a voice port.

trustpoint (credentials)

To specify the name of the trustpoint to be associated with a Cisco Unified CME CTL provider certificate or with the Cisco Unified SRST router certificate, use the trustpoint command in credentials configuration mode. To change the specified trustpoint, use the no form of this command.

trustpoint trustpoint-name

no trustpoint

 
Syntax Description

trustpoint-name

Name of the trustpoint to be associated with the Cisco Unified CME CTL provider certificate or the Cisco Unified SRST device certificate.

 
Command Default

No default behavior or values.

 
Command Modes

Credentials configuration (config-credentials)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.3(14)T

Cisco SRST 3.3

This command was introduced for Cisco SRST.

12.4(4)XC

Cisco Unified CME 4.0

This command was introduced for Cisco Unified CME.

12.4(9)T

Cisco Unified CME 4.0

This command for Cisco Unified CME was integrated into Cisco IOS Release 12.4(9)T.

 
Usage Guidelines

Cisco Unified CME

This command is used with Cisco Unified CME phone authentication to define the trustpoint for the CTL provider. This trustpoint will be used for TLS sessions with the CTL client.

Cisco Unified SRST

The name of the trustpoint must be consistent with the trustpoint name of the Cisco Unified SRST router.

Examples

Cisco Unified CME

The following example sets up a CTL provider on the Cisco Unified CME router with the IP address 172.19.245.1.

Router(config)# credentials

Router(config-credentials)# ip source-address 172.19.245.1 port 2444

Router(config-credentials)# trustpoint ctlpv

Router(config-credentials)# ctl-service admin user4 secret 0 c89L8o

Cisco Unified SRST

The following example enters credentials configuration mode, sets the IP source address and port, and specifies the trustpoint:

Router(config)# credentials

Router(config-credentials)# ip source-address 10.6.21.4 port 2445

Router(config-credentials)# trustpoint srstca

 
Related Commands

Description

ctl-service admin

Specifies a user name and password to authenticate the CTL client during the CTL protocol.

debug credentials

Sets debugging on the credentials service.

ip source-address (credentials)

Enables the router to receive messages through the specified IP address and port.

show credentials

Displays the credentials settings.

trustpoint-label

To specify the PKI trustpoint label to be used for the TLS connection between the CAPF server and the phone, use the trustpoint-label command in CAPF-server configuration mode. To return to the default, use the no form of this command.

trustpoint-label label

no trustpoint-label

 
Syntax Description

label

Trustpoint name for the CAPF server.

 
Command Default

No trustpoint label is specified for TLS connections.

 
Command Modes

CAPF-server configuration (config-capf-server)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.4(4)XC

Cisco Unified CME 4.0

This command was introduced.

12.4(9)T

Cisco Unified CME 4.0

This command was integrated into Cisco IOS Release 12.4(9)T.

 
Usage Guidelines

This command is used with Cisco Unified CME phone authentication to provide a PKI trustpoint name for the CAPF server. This trustpoint label is used for the TLS connection between the CAPF server and the phone.

Examples

The following example defines the CAPF server trustpoint name as server25.

Router(config)# capf-server

Router(config-capf-server)# source address 10.10.10.1

Router(config-capf-server)# trustpoint-label server25

Router(config-capf-server)# cert-oper upgrade all

Router(config-capf-server)# cert-enroll-trustpoint server12 password 0 x8oWiet

Router(config-capf-server)# auth-mode auth-string

Router(config-capf-server)# auth-string generate all

Router(config-capf-server)# port 3000

Router(config-capf-server)# keygen-retry 5

Router(config-capf-server)# keygen-timeout 45

Router(config-capf-server)# phone-key-size 2048

type (voice register pool)

To define a phone type for a SIP phone, use the type command in voice register pool configuration mode. To remove a phone type, use the no form of this command.

type phone-type [ addon 1 CKEM [ 2 CKEM [ 3 CKEM ]]]

no type

 
Syntax Description

phone-type

Type of SIP phone that is being defined. Valid entries are as follows:

  • 3905 —Cisco Unified IP Phone 3905.
  • 3951 —Cisco Unified IP Phones 3911 and 3951.
  • 6901 —Cisco Unified IP Phone 6901.
  • 6911 —Cisco Unified IP Phone 6911.
  • 6921 —Cisco Unified IP Phone 6921.
  • 6941 —Cisco Unified IP Phone 6941.
  • 6945 —Cisco Unified IP Phone 6945.
  • 6961 —Cisco Unified IP Phone 6961.
  • 7905 —Cisco Unified IP Phones 7905 and 7905G.
  • 7906 —Cisco Unified IP Phone 7906G.
  • 7911 —Cisco Unified IP Phone 7911G.
  • 7912 —Cisco IP Phones 7912 and 7912G.
  • 7940 —Cisco IP Phones 7940 and 7940G.
  • 7941 —Cisco IP Phone 7941G.
  • 7941GE —Cisco IP Phone 7941GE.
  • 7942 —Cisco Unified IP Phone 7942.
  • 7945 —Cisco Unified IP Phone 7945.
  • 7960 —Cisco IP Phones 7960 and 7960G.
  • 7961 —Cisco IP Phone 7961G.
  • 7961GE —Cisco IP Phone 7961GE.
  • 7962 —Cisco Unified IP Phone 7962.
  • 7965 —Cisco Unified IP Phone 7965.
  • 7970 —Cisco IP Phone 7970G.
  • 7971 —Cisco IP Phone 7971GE.
  • 7975 —Cisco Unified IP Phone 7975.
  • 8961 —Cisco Unified IP Phone 8961.
  • 9951 —Cisco Unified IP Phone 9951.
  • 9971 —Cisco Unified IP Phone 9971.
  • ATA —Cisco ATA-186 or Cisco ATA-188.
  • ATA-187 —Cisco ATA-187.
  • Jabber-Android —Cisco Jabber App on Android.
  • Jabber-Win
  • P100 —PingTel Xpressa 100.
  • P600 —Polycom SoundPoint 600.

addon 1 CKEM

(Optional) Tells the router that a Cisco SIP IP Phone CKEM 36-Button Line Expansion Module is being added to this Cisco Unified SIP IP phone.

Note This option is available to Cisco Unified 8961, 9951, and 9971 SIP IP phones only.

2 CKEM

(Optional) Tells the router that a second Cisco SIP IP Phone CKEM 36-Button Line Expansion Module is being added to this Cisco Unified SIP IP phone.

Note This option is available to Cisco Unified 9951 and 9971 SIP IP phones only.

3 CKEM

(Optional) Tells the router that a third Cisco SIP IP Phone CKEM 36-Button Line Expansion Module is being added to this Cisco Unified SIP IP phone.

Note This option is available to Cisco Unified 9971 SIP IP phones only.

 
Command Default

No phone type is defined.

 
Command Modes

Voice register pool configuration (config-register-pool)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.4(4)T

Cisco CME 3.4

This command was introduced.

12.4(11)XJ

Cisco Unified CME 4.1

This command was modified to add the 3951 , 7911 , 7941 , 7941GE , 7961 , 7961GE , 7970 , and 7971 keywords.

12.4(15)T

Cisco Unified CME 4.1

The 3951 , 7911 , 7941 , 7941GE , 7961 , 7961GE , 7970 , and 7971 keywords were integrated into Cisco IOS Release 12.4(15)T.

12.4(15)XZ

Cisco Unified CME 4.3

This command was modified to add the 7942 , 7945 , 7962 , 7965 , and 7975 keywords.

12.4(20)T

Cisco Unified CME 7.0

This command was integrated into Cisco IOS Release 12.4(20)T.

15.1(3)T

Cisco Unified CME8.5

This command was modified to add the 8961 , 9951 ,and 9971 keywords.

15.2(1)T

Cisco Unified CME 8.8

This command was modified to add the 3905 keyword.

15.2(2)T

Cisco Unified CME 9.0

This command was modified to add the 6901 , 6911 , 6921 , 6941 , 6945 , 6961 , ATA-187 , and Jabber-Android keywords.

15.2(4)M

Cisco Unified CME 9.1

This command was modified to include the addon 1 CKEM , 2 CKEM , and 3 CKEM keywords.

15.3(3)M

Cisco Unified CME 10.0

This command was modified. The Jabber-Win keyword was added.

 
Usage Guidelines

The addon 1 CKEM , 2 CKEM , and 3 CKEM keywords increase the number of speed-dial, busy-lamp-field, and directory number keys that can be configured.

There are two options in removing a Key Expansion Module (KEM) when you have configured all three KEMs.

The first option is to use the no form of the type command, then use the type command to configure only the KEMs to be included. The following example shows how the second and third KEMs are removed from the configuration:

Router(config)# voice register pool 9
Router(config-register-pool)# type 9971 addon 1 CKEM 2 CKEM 3 CKEM
Router(config-register-pool)# no type 9971 addon 1 CKEM 2 CKEM 3 CKEM
Router(config-register-pool)# type 9971 addon 1 CKEM
 

The second option is to define the same phone type while excluding from the configuration the KEM to be removed. For example, you have configured the following:

Router(config)# voice register pool 3
Router(config-register-pool)# type 9971 addon 1 CKEM 2 CKEM 3 CKEM
 

To remove the third KEM, enter the following:

Router(config-register-pool)# type 9971 addon 1 CKEM 2 CKEM

 

To remove the second KEM, enter the following:

Router(config-register-pool)# type 9971 addon 1 CKEM
 

After configuring the phone type, use the create profile command in voice register global configuration mode to generate the configuration profile files required for the phone and then reset or restart the phone using the reset or restart command, respectively.


Note Cisco Unified CME enables the busy trigger-per-button (voice register pool) command when phone-type 3905 is specified.


Examples

The following example shows how to define a SIP phone with phone-tag 10 as a Cisco Unified IP Phone 7960 or Cisco Unified IP Phone 7960G:

Router(config)# voice register pool 10
Router(config-register-pool)# type 7960

 
Related Commands

Command
Description

busy-trigger-per-button (voice register pool)

Sets the maximum number of calls allowed on a SIP directory number before activating Call Forward Busy or a busy tone.

load (voice register global)

Associates a type of Cisco Unified SIP IP phone with a phone firmware file.

reset (voice register global)

Performs a complete reboot of all SIP phones associated with a Cisco Unified CME router.

reset (voice register pool)

Performs a complete reboot of one SIP phone associated with a Cisco Unified CME router.

restart (voice register)

Performs a fast reset of one or all SIP phones associated with a Cisco Unified CME router.

voice register pool

Enters voice register pool configuration mode for SIP phones.

 

type (voice-gateway)

To define the type of voice gateway to autoconfigure, use the type command in voice-gateway configuration mode. To remove the type from the configuration, use the no form of this command.

type { vg202 | vg204 | vg224 }

no type

 
Syntax Description

vg202

Cisco VG202 Voice Gateway with 2 FXS ports.

vg204

Cisco VG204 Voice Gateway with 4 FXS ports.

vg224

Cisco VG224 Voice Gateway with 24 FXS ports.

 
Defaults

No type is defined for the voice gateway to be autoconfigured.

 
Command Modes

Voice-gateway configuration (config-voice-gateway)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.4(22)YB

Cisco Unified CME 7.1

This command was introduced.

12.4(24)T

Cisco Unified CME 7.1

This command was integrated into Cisco IOS Release 12.4(24)T.

 
Usage Guidelines

This command specifies the type of Cisco voice gateway for which you are creating an XML configuration file.

Examples

The following example shows a configuration for the Cisco VG224 voice gateway:

voice-gateway system 1

network-locale FR

type VG224

mac-address 001F.A30F.8331

voice-port 0-23

create cnf-files

 
Related Commands

Command
Description

create cnf-files (voice-gateway)

Generates the XML configuration files that are required to autoconfigure the Cisco voice gateway.

mac-address (voice-gateway)

Defines the MAC address of the voice gateway to autoconfigure.

voice-port (voice-gateway)

Identifies the ports on the voice gateway that register to Cisco Unified CME.

type (voice register dialplan)

To specify a phone type for a SIP dial plan, use the type command in voice register dialplan configuration mode. To remove a phone type, use the no form of this command.

type phone-type

no type

 
Syntax Description

phone-type

Type of SIP phone for which the dial plan is used. Values are:

  • 7905-7912 —Cisco Unified IP Phone 7905, 7905G, 7912, or 7912G.
  • 7940-7960-others —Cisco Unified IP Phone 7911, 7940, 7940G, 7941, 7942, 7941GE, 7945, 7960, 7960G, 7961, 7961GE, 7962, 7965, 7970, 7971, or 7975.

 
Command Default

The phone type is not defined.

 
Command Modes

Voice register dialplan configuration (config-register-dialplan)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.4(11)XJ

Cisco Unified CME 4.1

This command was introduced.

12.4(15)T

Cisco Unified CME 4.1

This command was integrated into Cisco IOS Release 12.4(15)T.

12.4(15)XZ

Cisco Unified CME 4.3

Support for Cisco Unified IP Phone 7942, 7945, 7962, 7965, and 7975 was added.

12.4(20)T

Cisco Unified CME 7.0

This command was integrated into Cisco IOS Release 12.4(20)T.

 
Usage Guidelines

This command specifies the type of SIP phone for which the dial plan is defined. You must use this command before defining dial patterns with the pattern command or selecting a dial pattern file in flash with the filename command.

The phone type specified with this command must match the phone type specified with the type command in voice register pool mode. If the dial plan type does not match the type assigned to the phone, the dial-plan configuration file is not generated.

Examples

The following example shows a SIP dial plan being defined for a Cisco Unified IP Phone 7905 or Cisco Unified IP Phone 7912:

Router(config)# voice register dialplan 10

Router(config-register-dialplan)# type 7905-7912

Router(config-register-dialplan)# pattern 52...

Router(config-register-dialplan)# pattern 91.......

 
Related Commands

Command
Description

dialplan

Assigns a dial plan to a SIP phone.

filename

Specifies a custom XML file that contains the dial patterns to use for the SIP dial plan.

pattern (voice register dialplan)

Defines a dial pattern for a SIP dial plan.

show voice register dialplan

Displays configuration information for a specific SIP dial plan.

type (voice register pool)

Defines a phone type for a SIP phone.

type (voice register pool)

To define a phone type for a SIP phone, use the type command in voice register pool configuration mode. To remove a phone type, use the no form of this command.

type phone-type [ addon 1 CKEM [ 2 CKEM [ 3 CKEM ]]]

no type

 
Syntax Description

phone-type

Type of SIP phone that is being defined. Valid entries are as follows:

  • 3905 —Cisco Unified IP Phone 3905.
  • 3951 —Cisco Unified IP Phones 3911 and 3951.
  • 6901 —Cisco Unified IP Phone 6901.
  • 6911 —Cisco Unified IP Phone 6911.
  • 6921 —Cisco Unified IP Phone 6921.
  • 6941 —Cisco Unified IP Phone 6941.
  • 6945 —Cisco Unified IP Phone 6945.
  • 6961 —Cisco Unified IP Phone 6961.
  • 7905 —Cisco Unified IP Phones 7905 and 7905G.
  • 7906 —Cisco Unified IP Phone 7906G.
  • 7911 —Cisco Unified IP Phone 7911G.
  • 7912 —Cisco IP Phones 7912 and 7912G.
  • 7940 —Cisco IP Phones 7940 and 7940G.
  • 7941 —Cisco IP Phone 7941G.
  • 7941GE —Cisco IP Phone 7941GE.
  • 7942 —Cisco Unified IP Phone 7942.
  • 7945 —Cisco Unified IP Phone 7945.
  • 7960 —Cisco IP Phones 7960 and 7960G.
  • 7961 —Cisco IP Phone 7961G.
  • 7961GE —Cisco IP Phone 7961GE.
  • 7962 —Cisco Unified IP Phone 7962.
  • 7965 —Cisco Unified IP Phone 7965.
  • 7970 —Cisco IP Phone 7970G.
  • 7971 —Cisco IP Phone 7971GE.
  • 7975 —Cisco Unified IP Phone 7975.
  • 8961 —Cisco Unified IP Phone 8961.
  • 9951 —Cisco Unified IP Phone 9951.
  • 9971 —Cisco Unified IP Phone 9971.
  • ATA —Cisco ATA-186 or Cisco ATA-188.
  • ATA-187 —Cisco ATA-187.
  • Jabber-Android —Cisco Jabber App on Android.
  • P100 —PingTel Xpressa 100.
  • P600 —Polycom SoundPoint 600.

addon 1 CKEM

(Optional) Tells the router that a Cisco SIP IP Phone CKEM 36-Button Line Expansion Module is being added to this Cisco Unified SIP IP phone.

Note This option is available to Cisco Unified 8961, 9951, and 9971 SIP IP phones only.

2 CKEM

(Optional) Tells the router that a second Cisco SIP IP Phone CKEM 36-Button Line Expansion Module is being added to this Cisco Unified SIP IP phone.

Note This option is available to Cisco Unified 9951 and 9971 SIP IP phones only.

3 CKEM

(Optional) Tells the router that a third Cisco SIP IP Phone CKEM 36-Button Line Expansion Module is being added to this Cisco Unified SIP IP phone.

Note This option is available to Cisco Unified 9971 SIP IP phones only.

 
Command Default

No phone type is defined.

 
Command Modes

Voice register pool configuration (config-register-pool)

 
Command History

Cisco IOS Release
Cisco Product
Modification

12.4(4)T

Cisco CME 3.4

This command was introduced.

12.4(11)XJ

Cisco Unified CME 4.1

This command was modified to add the 3951 , 7911 , 7941 , 7941GE , 7961 , 7961GE , 7970 , and 7971 keywords.

12.4(15)T

Cisco Unified CME 4.1

The 3951 , 7911 , 7941 , 7941GE , 7961 , 7961GE , 7970 , and 7971 keywords were integrated into Cisco IOS Release 12.4(15)T.

12.4(15)XZ

Cisco Unified CME 4.3

This command was modified to add the 7942 , 7945 , 7962 , 7965 , and 7975 keywords.

12.4(20)T

Cisco Unified CME 7.0

This command was integrated into Cisco IOS Release 12.4(20)T.

15.1(3)T

Cisco Unified CME8.5

This command was modified to add the 8961 , 9951 ,and 9971 keywords.

15.2(1)T

Cisco Unified CME 8.8

This command was modified to add the 3905 keyword.

15.2(2)T

Cisco Unified CME 9.0

This command was modified to add the 6901 , 6911 , 6921 , 6941 , 6945 , 6961 , ATA-187 , and Jabber-Android keywords.

15.2(4)M

Cisco Unified CME 9.1

This command was modified to include the addon 1 CKEM , 2 CKEM , and 3 CKEM keywords.

 
Usage Guidelines

The addon 1 CKEM , 2 CKEM , and 3 CKEM keywords increase the number of speed-dial, busy-lamp-field, and directory number keys that can be configured.

There are two options in removing a Key Expansion Module (KEM) when you have configured all three KEMs.

The first option is to use the no form of the type command, then use the type command to configure only the KEMs to be included. The following example shows how the second and third KEMs are removed from the configuration:

Router(config)# voice register pool 9
Router(config-register-pool)# type 9971 addon 1 CKEM 2 CKEM 3 CKEM
Router(config-register-pool)# no type 9971 addon 1 CKEM 2 CKEM 3 CKEM
Router(config-register-pool)# type 9971 addon 1 CKEM
 

The second option is to define the same phone type while excluding from the configuration the KEM to be removed. For example, you have configured the following:

Router(config)# voice register pool 3
Router(config-register-pool)# type 9971 addon 1 CKEM 2 CKEM 3 CKEM
 

To remove the third KEM, enter the following:

Router(config-register-pool)# type 9971 addon 1 CKEM 2 CKEM

 

To remove the second KEM, enter the following:

Router(config-register-pool)# type 9971 addon 1 CKEM
 

After configuring the phone type, use the create profile command in voice register global configuration mode to generate the configuration profile files required for the phone and then reset or restart the phone using the reset or restart command, respectively.


Note Cisco Unified CME enables the busy trigger-per-button (voice register pool) command when phone-type 3905 is specified.


Examples

The following example shows how to define a SIP phone with phone-tag 10 as a Cisco Unified IP Phone 7960 or Cisco Unified IP Phone 7960G:

Router(config)# voice register pool 10
Router(config-register-pool)# type 7960

 
Related Commands

Command
Description

busy-trigger-per-button (voice register pool)

Sets the maximum number of calls allowed on a SIP directory number before activating Call Forward Busy or a busy tone.

load (voice register global)

Associates a type of Cisco Unified SIP IP phone with a phone firmware file.

reset (voice register global)

Performs a complete reboot of all SIP phones associated with a Cisco Unified CME router.

reset (voice register pool)

Performs a complete reboot of one SIP phone associated with a Cisco Unified CME router.

restart (voice register)

Performs a fast reset of one or all SIP phones associated with a Cisco Unified CME router.

voice register pool

Enters voice register pool configuration mode for SIP phones.