Table Of Contents
Release Notes for Cisco Business Edition 3000, Release 8.6(4)
June 25, 2 01 2
This document contains information on the following topics:
These release notes are based on the 220.127.116.1100-1 software version of Cisco Business Edition 3000 for Release 8.6(4). The Cisco Business Edition 3000 server comes preinstalled with Cisco Business Edition 3000, and is provided as an appliance.
Cisco Business Edition 3000, a system under the Cisco Unified Communications family of products, provides an IP telephony solution that enables the following options:
•Easy setup of deployments
•Easy provisioning of users, phones, lines, and phone features
•Easy monitoring and troubleshooting
•Easy maintenance of your system (for example, simplified backups and restores)
The Cisco Business Edition 3000 software is preinstalled in your system so that you do not have to perform a software installation to get your server up and running. Deployment of the Cisco Business Edition 3000 server, phones, and the gateway across an IP network provides a distributed virtual-telephony network. Quality of service is maintained across constricted WAN links, the Internet, or VPN connections.
Your Cisco Business Edition 3000 system is designed to support up to 300 users and 400 phones. Supplementary and enhanced services such as hold, transfer, forward, conference, multiple-line appearances, speed dials, last-number redial, and other features extend to the phones.
Web-browser interfaces allow configuration of the system. These interfaces also provide access to online help.
For more complete information about Cisco Business Edition 3000, see the Administration Guide for Cisco Business Edition 3000 at the following URL:
For minimum requirements for products that work with Cisco Business Edition 3000, see the Software Compatibility Matrix for Cisco Business Edition 3000, which you can obtain at the following URL:
New and Changed Information
For a list of documents to review before you configure the Cisco Business Edition 3000 system, see the "Related Documentation" section.
You can view documentation that supports this release of Cisco Business Edition 3000 at the following URL: http://www.cisco.com/en/US/products/ps11370/tsd_products_support_series_home.html.
Review the following documentation before you configure Cisco Business Edition 3000 Release 8.6(3):
•The Software Compatibility Matrix for Cisco Business Edition 3000, which lists the minimum software requirements for the products that are supported with Cisco Business Edition 3000.
•The Cisco Unified IP Phone 6900 Firmware Upgrade from 8.5 (x) to 9.2(1), which provides guidelines and best practices on how to upgrade Cisco Unified IP Phones 6921, 6941, and 6961 from Firmware Version 8.5(x) SCCP Unsigned to Version 9.2(1) or current shipping version so they can successfully register on a Cisco Business Edition 3000 server.
•The Administration Guide for Cisco Business Edition 3000, which provides important information on how to configure and troubleshoot your system. This document is available in English, Mandarin, German, Italian, Portuguese, Spanish, and French.
•The Cisco MCS 7890-C1 Business Edition 3000 Appliance User Guide, which provides procedural information for users who are operating the Cisco MCS 7890-C1.
Note Obtain the preceding documents at the following URL:
For the GUIs, online help is displayed in English, Mandarin, German, Italian, Portuguese, Spanish, or French, depending on the country-pack preference that you configure. Field descriptions are displayed for the settings in the GUIs. Use the online help in conjunction with the Administration Guide for Cisco Business Edition 3000, which includes more information on Cisco Business Edition 3000.
Review the following important information before you configure Cisco Business Edition 3000. See the following sections:
Obtaining Files for Cisco Business Edition 3000 on www.cisco.com
Table 1 lists where you can obtain important files that are used with Cisco Business Edition 3000. For example, Table 1 lists where to go to get the Cisco-provided .xls data configuration file, the Cisco-provided country packs, the upgrade files, the Cisco User Connect licenses, and other important files. Before you use these files, review the Administration Guide for Cisco Business Edition 3000.
Table 1 Where to Obtain Files for Cisco Business Edition 3000
Files Description Where to Find the Files
Referenced to configure the system
See the "Related Documentation" section.
Cisco User Connect licensing site
Needed to order Cisco User Connect licenses
Go to the following URL to download the various files that you use with Cisco Business Edition 3000:
Cisco-provided .xls data configuration file—
cuba_install.zip (containing cuba_install.xls)
Needed to enter configuration data for automatic setup
Network Configuration Signature file—
Required for setting up server to access your network
Required for upgrading software, firmware, locale updates, and dial plan updates
Cisco-provided country packs
Needed to install localized dial plans and locales (tones and language)
Cisco Diagnostics USB Signature file— diagnose.xml
Needed to troubleshoot when you cannot access the GUIs
Required to reimage the server (for troubleshooting only when your technical support team advises that you reimage the server)
All installation parameters are provided with this file and cannot be modified.
Default username: admin
Cisco Business Edition 3000 and USB Usage
For many tasks that you can perform in Cisco Business Edition 3000, you can use a USB key or USB hard disk if the file exists on the USB device. Instead of using a USB device, you can use the PC desktop or SFTP server for many of these tasks, as described in the Administration Guide for Cisco Business Edition 3000. This section only describes USB usage for these tasks; it does not describe the SFTP server or PC desktop options.
Caution You can purchase the USB devices at any retailer. Cisco does not provide support for the USB devices through the Cisco Technical Assistance Center (TAC). If you have issues with the USB hardware, contact the manufacturer of the USB device or the retailer where you purchased the device.
Before you use a USB key, you must download the Network Configuration Signature file (configure.xml) from http://www.cisco.com/cisco/software/navigator.html?mdfid=283661240&flowid=26421, edit the file with valid network information (such as IP address, subnet mask, and gateway configuration), and save the updated copy in the USB key.
Cisco recommends two USB keys: one for diagnostics and one for recovery (network configuration). The USB key that you use for recovery does not modify the existing network setting of your machine. When the network configuration USB key is inserted into the system, temporary network access is established, allowing you to access the Cisco Business Edition 3000 Administrative Interface. This temporary network access is automatically disabled if the machine is restarted.
When you modify the network configuration USB key, open the temporary IP address in your browser; then, log in to the Cisco Business Edition 3000 Administrative Interface and modify the network settings to reflect the changes that you made in the temporary network interface so that the modifications are permanent.
Note Cisco recommends that you use two dedicated USB keys for network configuration (recovery) and diagnostics. You should copy the Network Configuration Signature file (configure.xml) to the network configuration USB key and the Diagnostics Signature file (diagnose.xml) to the Diagnostics USB key.
Phone Firmware Upgrades
Cisco Unified IP Phone 6900 Series is compatible with Cisco Business Edition 3000. Cisco Unified IP Phone 6900 Series with 9.0(2) SCCP phone firmware automatically upgrades to 9.2(1) SIP firmware.
If you have 8.5 SCCP firmware on 6900 Series phones, see the Cisco Unified IP Phone 6900 Firmware Upgrade from 8.5 (x) to 9.2(1) Troubleshooting TechNote that describes how to upgrade to 9.2(1) SIP or a later firmware version at the following URL:
CSCtj88176 Default to Internal USB Key Requires User to Select External USB Key
Note The following procedure is applicable only to the MCS 7816-I5 server. It does not apply to the
Be aware that the following operations display the internal USB key "SMART" by default during the USB key process. For each scenario, you must select the external USB key for each of these components to work properly.
•Spreadsheet (for manual setup mode)
•USB Country Pack
Note The name of the external USB key depends on the type of USB key that you have.
Figure 1 Internal USB Key Displayed While License Is Copied
Figure 1 shows that by default the internal USB key is displayed while the license file is copied. Select the external USB key to copy the license file.
Figure 2 Internal USB Key Displayed While Spreadsheet Is Copied
Figure 2 shows that by default the internal USB key is displayed while the configuration spreadsheet is copied. Select the external USB key to copy the configuration spreadsheet.
Figure 3 Internal USB Key Displayed for Users/Phones Operation
Figure 3 shows that by default the internal USB key is displayed for the Users/Phones operation. Select the external USB key to copy the Users/Phones information.
Figure 4 Internal USB Key Displayed During Backup Operation
Figure 4 shows that by default the internal USB key is displayed during a backup operation. Select the external USB key for a backup operation.
CD/DVD USB Drive Support for Cisco Business Edition 3000 8.6(4)
The Cisco MCS 7890-C1 requires an external USB 2.0 CD/DVD drive for reimaging or performing a server recovery. The following drives have been tested and are compatible with the Cisco MCS 7890-C1:
You can use other USB CD/DVD drive models, provided they meet the following specifications:
•Up to 52x24x52x write/rewrite/read CD speeds
•Up to 16x DVD-ROM read speeds
•USB 2.0 interface
•External power supply
•Support Dual-Layer DVD
Telnet Limitation for Cisco Unified SIP Phone 3905
Cisco Business Edition 3000 does not support the use of Telnet to connect to the Cisco Unified SIP Phone 3905 while troubleshooting and during phone maintenance.
Call Pickup Feature Limitation
Call Pickup allows you to answer a call that is ringing on a coworker's phone by redirecting the call to your phone. Cisco Business Edition 3000 supports only the Directed Call Pickup feature on Cisco Unified SIP Phone 3905.
CSCtq34429 FTS spreadsheet upload failed with error message though fills all details
When you use the data configuration file, which is a Cisco-provided .xls spreadsheet template, for automatic setup during the Cisco Business Edition 3000 First Time Setup Wizard, the system automatically uses the default values for settings that are not mandatory in the file. In rare cases, the spreadsheet upload fails without showing any error notifications. The spreadsheet upload failure can have various causes—for example, incorrect configuration settings in multiple FTS pages.
Note Cisco Business Edition 3000 does not check the integrity of the configuration data until after the Cisco-provided .xls data configuration file is inserted into the system.
For the automatic setup to succeed, you must review and update the settings in the FTS file and try uploading the spreadsheet again. The following are a few examples of FTS settings that can get configured incorrectly:
•Network tab—Invalid inputs for IP Address(System), IP Address(Media Resource), Subnet Mask, or Default Gateway.
•PSTN Gateway tab—Invalid inputs for Line Coding and Framing—One of these or both the ports (Port 0/0/0 and Port 1).
•Dial Plan tab—Invalid inputs for Operator Dial Code, Outside Dial Code, Feature Dial Code, or Interdigit Timeout.
•Sites tab—Invalid Local Area Codes for Central Sites. Make sure that you add appropriate values for Additional Emergency Services and Emergency Location ID Numbers; else, keep these fields empty.
CSCts28780 No MWI indication on WebEx Connect softphone (Cisco Business Edition 3000)
Cisco Business Edition 3000 supports the Cisco UC Integration for Cisco WebEx Connect Administration Tool, which enables administrators to monitor, manage, control, and enhance user access to Cisco WebEx Connect.
Note Cisco Business Edition 3000 does not support the Message Waiting Indicator (MWI) feature that notifies the user when a new voice message is delivered.
CSCua36393 Cannot dial 911 when using Dial Plan prefix 9 on Cisco Business Edition 3000
In North America, Cisco Business Edition 3000 does not allow users to make emergency calls directly, for example 911, 1911, and 101XXXX911. You will have to download cop file `ciscocm_emergency_911.cop.sgn' to make emergency calls directly. This version of the COP file contains fix for this limitation which allows the users to make emergency calls without the outside dial code for North America Numbering Plan. You can download the `ciscocm_emergency_911.cop.sgn' from the Software Download page on Cisco.com avalaible at http://www.cisco.com/cisco/software/release.html?mdfid=283783671&flowid=26421&softwareid=283688477&release=8.6%284%29&relind=AVAILABLE&rellifecycle=&reltype=latest.
The Readme file describes the process to upgrade the server with the COP file. For more instruction on how to install the cop file, download the ReadMe file from http://www.cisco.com/cisco/software/release.html?mdfid=283783671&flowid=26421&softwareid=283688477&release=8.6%284%29&relind=AVAILABLE&rellifecycle=&reltype=latest.
CSCub60533 Speed dial allows only 40 numbers
The Cisco Business Edition 3000 Administration Guide states that you can have up to 48 speed dials. This number is incorrect. Cisco Business Edition 3000 allows only 40 speed dials.
This section lists the resolved Voicemail caveats in Cisco Business Edition 3000 Release 8.6(4).
Table 3 Resolved Caveats for Voicemail in Release 8.6(4) as of May 17, 2012
The following sections contain information on how to obtain the latest resolved caveat information and latest open caveat information for bugs of severity levels 1, 2, and 3.
Caveats describe unexpected behavior for Cisco Business Edition 3000. Severity 1 caveats represent the most serious caveats, severity 2 caveats represent less serious caveats, and severity 3 caveats represent moderate caveats.
See the following sections:
Using Bug Toolkit
You can search for the latest resolved and open caveats by using the Cisco Software Bug Toolkit. To access the Cisco Software Bug Toolkit, you need the following items:
•Cisco.com user ID and password
To use the Cisco Software Bug Toolkit, perform the following procedure:
Step 1 Access the Cisco Software Bug Toolkit at http://tools.cisco.com/Support/BugToolKit.
Step 2 Log in with your Cisco.com user ID and password.
Step 3 If you are looking for information about a specific problem, enter the bug ID number in the Search for Bug ID field, and click Go.
Tip Click Help on the Bug Toolkit page for information about how to search for bugs, create saved searches, and create bug groups.
These release notes do not list the resolved caveats because Cisco Software Bug Toolkit provides the latest list of resolved and open caveats. You can find the latest resolved caveat information by using the Cisco Software Bug Toolkit, as described in the "Using Bug Toolkit" section.
These release notes list the caveats that are open as of April 11, 2012. These release notes contain descriptions of the following:
•All severity level 1 or 2 caveats
•Significant severity level 3 caveats
Note Because caveat status continually changes, be aware that the Table 4, "Open Caveats for Cisco Business Edition 3000 Release 8.6(4) as of June 25 2012" reflects a snapshot of the caveats that were open at the time this report was compiled. For an updated view of open caveats, access Bug Toolkit and follow the instructions described in the "Using Bug Toolkit" section.
Table 4 Open Caveats for Cisco Business Edition 3000 Release 8.6(4) as of June 25 2012
Open Caveats for Cisco Unified Communications Manager Release 8.6(2a)
Open caveats for Unified CM Release 8.6(2a) also describe possible unexpected behaviors in the Cisco Business Edition 3000. So, all the open caveats that apply to the Unified CM apply to the Cisco Business Edition 3000 as well.
For information on the list of open caveats for Unified CM, see the release notes for Cisco Unified Communications Manager at the following URL:
The Documentation Updates section contains information on errors, omissions, and changes for the Administration Guide for Cisco Business Edition 3000 and online help. See the following sections:
CSCto58908—Alarm on Health Summary when Channels Are not Configured on PSTN
The English, Mandarin, German, Italian, Portuguese, Spanish, and French online help for Cisco Business Edition 3000 Administrative Interface does not include the following troubleshooting information when the system is nearing maximum call capacity.
An alarm is generated when PSTN calls utilization nears 100%. PSTN calls will not be established after utilization reaches 100% when the following situations occur:
•All the channels are busy
•The PSTN configuration settings are incorrect
•One or more channels are not functioning properly
•There is an error in the service provider settings
Perform any of the following actions:
•Review the reports for high call volume on the Call Detail Reports page (Monitoring > Call Detail Reports).
•Reduce the number of inbound and outbound calls.
•Make sure that you select the proper channel selection order. For example, if you lease channels 1 to 15, you must have the channel selection order as top-down. If you did not lease the entire PRI span from the service provider, enter only the partial channel range that is available.
If this problem persists, contact your technical support team; for example, contact your Value Added Reseller (VAR), or if you are the Value Added Reseller, contact the Cisco Technical Assistance Center (TAC).
CSCts02379—Unable to See Troubleshooting Information when Fan Speed Goes Out of Threshold
The system fan is not operating properly and the system must be powered down and then restarted.
The system fan is not operating properly.
Restart the server. (Select Maintenance > Restart/Shutdown.)
CSCty99857—AT&T: New parameter introduced after upgrade from Release 8.6(3) to Release 8.6(4)
The system displays a new parameter "Use Device Pool Called Party Transformation CSS" on the PSTN Connections > Edit > Advanced Settings page on the Cisco Business Edition 3000 Administrative Interface for a SIP trunk connection.
After you migrate from Cisco Business Edition 3000 Release 8.6(3) to Cisco Business Edition 3000 Release 8.6(4), the calls are not processed through the SIP trunk.
After migration, update the connection pack for the SIP trunk in your system. If necessary, update the Called Party Transformation Patterns and the Digit Discard Instructions under the Outbound Call Routing Information on PSTN Connections > Edit > Advanced Settings page on the Cisco Business Edition 3000 Administrative Interface for the SIP trunk connection.
CSCua26786—"Redial" word need to change in the Default ODC description in site page
If you have configured more than one outside dial code on the System Settings > Dial Plan > General Settings page, the Default Outside Dial Code option is enabled on the Connections > Sites > Call Settings > PSTN Access page.
The description for the Default Outside Dial Code field is changed to Used for Click-to-Call, dialing via missed/received call history and emergency calls routed through FXO" in the Connections > Sites > Call Settings > PSTN Access page on the Cisco Business Edition 3000 Administrative Interface.
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at
Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop by using a reader application. Be aware that the RSS feeds are a free service, and Cisco currently supports RSS Version 2.0.
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
© 2012 Cisco Systems, Inc. All rights reserved