Administration Guide for Cisco Business Edition 3000, Release 8.6(3)
Diagnostics Settings
Downloads: This chapterpdf (PDF - 383.0 KB) The complete bookPDF (PDF - 4.91 MB) | Feedback

Diagnostics Settings

Diagnostics Settings

GUI: Cisco Business Edition 3000 Administrative Interface

The Diagnostics page allows you to run diagnostics for your system, gather diagnostic information for your system, and download the diagnostic information. On the Diagnostics page, you can collect logs, enable or disable loopback for T1/E1 interfaces, and download the USB diagnostics file.

For more information, see the How to Diagnose a Problem.

The following topics contain information about the tabs and settings that are displayed on the Diagnostics page (Monitoring > Diagnostics).

Collect Logs

The following table describes the settings that you can use to enable or disable detailed logging, generate logs, and download the log file under the Collect Logs tab.

Table 1 Settings on the Collect Logs tab



Enable Logging

To enable the system to collect debug level log data, click Enable Logging. After you click this button, it grays out and the Disable Logging button becomes enabled. You can now attempt to reproduce your system issue.

Tip    Turning on logging may impact system performance, so enable logging only when necessary. After you finish collecting log data, remember to disable logging by clicking Disable Logging.

Disable Logging

When you have reproduced the system issue, click Disable Logging to stop the system from collecting log data. After you click this button, it grays out and the Enable Logging button becomes enabled.

Generate Log File

To prepare a log file, click Generate Log File.

Tip    You can generate a log file without enabling/disabling the logging functionality by clicking Generate Log File at any time and downloading the current log collection file.

The system displays the progress of the log file generation. When the log file is complete, a link displays that you can click to download the file to your PC. The link contains the time and date that the log file was created.

Tip    Be sure to download the file to a location on your PC that contains enough disk space to accommodate the size of the log file.

USB Flash Drive

Cisco USB flash drive allows you to perform the server diagnostics and collect the required log files when the Cisco Business Edition 3000 Administrative Interface is not accessible. You can use the USB Flash Drive tab to download the diagnostics file.


Ensure that the USB flash drive has a storage space of 4 GB. If there is not sufficient storage space, the files smaller than 4 GB will be copied to the USB.

To download the USB diagnostics file, click Download Diagnostics File. The USB diagnostics file allows the Value Added Reseller (VAR) and Cisco Technical Assistance Center (TAC) to provide additional troubleshooting assistance, especially when you cannot access the Cisco Business Edition 3000 Administrative Interface.

Packet Capture

The Cisco Business Edition 3000 Administrative Interface supports capturing the network packets on a server. While troubleshooting, it is sometimes necessary to collect network packets that are being sent to and from the network interface on a Cisco Business Edition 3000 server.

The following table describes the settings on the Packet Capture tab.


Packet Capture is resource-intensive and the system might be less responsive while it is enabled.

Table 2 Settings on the Packet Capture tab



Capture Packets

Packet Capture allows you to capture the network packets in two ways:

  • Capture packets to and from IP address—Choose this option to capture the network packets to and from a particular IP address.
  • Capture all packets—Choose this option to capture all the network packets.

Start Packet Capture

To start packet capture, click Start Packet Capture. The time stamp displays the current date and packet capture start time.

If the packet capture file exists on a system, the following warning message appears:


You can keep only one packet capture file on the server at a time. If you generate a new one, the existing file will be replaced with the new one.

While the packet capture is running, you can also attempt to reproduce the problem.

Stop Packet Capture

To stop the packet capturing, click Stop Packet Capture. The time stamp displays the current date and packet Capture stop time.

Packet capture stops when it captures 100,000 network packets.

The captured packets are saved in Packetcapture< Timestamp in YYYY-MM-DD_hh-mm-ss>.cap file format. The time stamp displays the time when the packet capturing was started.

Download the log file to your PC

A link allows you to download the captured network packets to your PC.


You should have the corresponding software tools installed on your PC to view the downloaded network packets.


Cisco Business Edition 300 Administrative Ping utility interface allows you to check the network connectivity for the desired IP Address or a hostname to which you want reach. While check the connectivity, you can mention the number of attempts that the system can try.

The following table describes the test characters that the ping facility sends.

Table 3 Settings on the Ping tab



Ping function

To check connectivity by using the Ping utility, perform the following:

  • Type the hostname or IP address to be reached. If DNS is not available on server, entering hostname will not work
  • Select the number of the Ping Attempts from the drop-drown list. After reaching the specified number of attempts mentioned in the drop-down list, the Ping operation will be automatically stopped. By default, the number is 1. The other available attempts are 5, 25, and 100.

Start Ping

To start a ping session, click the Start Ping button. Ping stops automatically after reaching the specified iteration number. The output shows the results of the Ping Attempts with the results summarized at the end.

Cancel Ping

After you click the Start Ping button, the button label changes to Cancel Ping and allows you to cancel the ping session. Ping statistics will not be available if ping is cancelled.


If you click the Cancel Ping button in the middle of a ping process, the ping operation is cancelled for the remaining iterations. A message appears in the Ping output box stating Ping Cancelled.

Gateway Loopback

The following table describes the settings on the Gateway Loopback tab. Your service provider uses loopback test to diagnose connection problems in the network and may ask you to put your T1/E1 interfaces (ports) into loopback mode. You can use the settings on the Gateway Loopback tab to enable or disable loopback mode for the internal gateway ports.


Do not add, update, or delete any of the internal gateway ports when you put a port in loopback mode. Adding, updating, or deleting a port can reset the internal gateway and will pull the port out of loopback mode.


You can use the Gateway Loopback tab to initiate loopback for internal gateways only. It is not applicable for external gateways.

Table 4 Settings on the Gateway Loopback tab




Displays all the internal PSTN gateway ports.

Connection Name

Displays the name of the gateway to which the port belongs.


Provides a brief description of the port.


Displays the status of the port, that is, up, down, or unregistered.

Enable Loopback

To put a port in loopback mode, click Enable Loopback. After you click this option, you can either Disable Loopback or Cancel.

After you put a port in loopback mode, the gateway to which that port belongs is unregistered. You can verify this through the Health Summary page.

Tip    You cannot enable loopback if the gateway for that port is not configured.

Disable Loopback

When your service provider completes the testing and asks you to disable loopback, click Disable Loopback to recover the port from loopback. After you click this option, it changes to Enable Loopback.