Cisco Unified Communications Manager Managed Services Guide, Release 9.1(1)
Vendor-specific Management Information Base
Downloads: This chapterpdf (PDF - 553.0KB) The complete bookPDF (PDF - 9.35MB) | Feedback

Vendor-specific Management Information Base

Contents

Vendor-specific Management Information Base

This chapter describes the vendor-specific Management Information Base (MIB) text documents that Cisco Unified Communications Manager (Cisco Unified CM) supports and that are used with Simple Network Management Protocol (SNMP).

Vendor-specific Management Information Base

The MIBs described in this chapter exist on various Cisco Media Convergence Servers (MCS), depending on vendor and model number. To query these MIBS, you can use the standard MIB browsers provided by the vendor. Go to the following URLs:

Supported servers - Cisco Unified CM releases

This section lists the supported server models and unsupported server models by MIB and by Cisco Unified CM Release.

Cisco Unified CM release 8.5(1) supported servers

Table 1 Servers available in Cisco Unified CM release 8.5(1)

Cisco Unified CM Release 8.5(1)

IBM Server Models

HP Server Models

Cisco Unified Computing System

  • MCS-7816-I3-IPC1
  • MCS-7816-H3-IPC1
  • UCS B200 M1
  • MCS-7816-I4-IPC1/CCX1
  • MCS-7825-H2-IPC1
  • UCS C210 M1
  • MCS-7816-I5-IPC1/CCX1
  • MCS-7825-H3-IPC1

  • MCS-7825-I3-IPC1
  • MCS-7825-H4-IPC1

  • MCS-7825-I4-IPC1
  • MCS-7828-H3-IPC1

  • MCS-7825-I5-IPC1
  • MCS-7835-H2-IPC1

  • MCS-7828-I3-SS1
  • MCS-7835-H2-IPC2

  • MCS-7828-I4-SS1
  • DL380G6 (Single E5504 CPU)

  • MCS-7828-I5-SS1
  • MCS-7845-H2-IPC1

  • MCS-7835-I2-IPC1
  • MCS-7845-H2-IPC2

  • MCS-7835-I2-IPC2
  • DL380G6 (Single E5540 CPU)

  • MCS-7835-I3-IPC1

  • MCS-7845-I2-IPC1

  • MCS-7845-I2-IPC2

  • MCS-7845-I3-IPC1

Cisco Unified CM release 8.5(1) inapplicable MIBs

IBM-SYSTEM-POWER MIB does not apply to the following IBM server models:

  • MCS-7815-I2-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7816-I4-IPC1/CCX1
  • MCS-7816-I5-IPC1/CCX1
  • MCS-7825-I2-IPC1
  • MCS-7825-I3-IPC1
  • MCS-7825-I4-IPC1
  • MCS-7825-I5-IPC1
  • MCS-7828-I3-SS1
  • MCS-7828-I4-SS1
  • MCS-7828-I5-SS1

IBM-SYSTEM-RAID MIB does not apply to the following IBM server models:

  • MCS-7815-I2-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7816-I4-IPC1/CCX1
  • MCS-7816-I5-IPC1/CCX1
  • MCS-7825-I4-IPC1
  • MCS-7825-I5-IPC1
  • MCS-7828-I4-SS1
  • MCS-7828-I5-SS1
  • MCS-7835-I3-IPC1
  • MCS-7845-I3-IPC1

IBM-SYSTEM-STORAGE-MIB does not apply to the following IBM server models:

  • MCS-7815-I2-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7816-I4-IPC1/CCX1
  • MCS-7816-I5-IPC1/CCX1
  • MCS-7825-I2-IPC1
  • MCS-7825-I3-IPC1
  • MCS-7828-I3-SS1
  • MCS-7835-I2-IPC1
  • MCS-7835-I2-IPC2
  • MCS-7845-I2-IPC1
  • MCS-7845-I2-IPC2

HP CPQSCSI MIB does not apply to the following HP server model:

  • MCS-7816-H3-IPC1
  • MCS-7825-H2-IPC1
  • MCS-7825-H3-IPC1
  • MCS-7825-H4-IPC1
  • MCS-7828-H3-IPC1
  • MCS-7835-H2-IPC1
  • MCS-7835-H2-IPC2
  • DL380G6 (Single E5504 CPU)
  • MCS-7845-H2-IPC1
  • MCS-7845-H2-IPC2
  • DL380G6 (Single E5540 CPU)

Cisco Unified CM release 8.0(2) supported servers

Table 2 Servers available in Cisco Unified CM release 8.0(2)

Cisco Unified CM Release 8.0(2)

IBM Server Models

HP Server Models

Cisco Unified Computing System

  • MCS-7815-I2-IPC1
  • MCS-7816-H3-IPC1
  • UCS B200 M1
  • MCS-7816-I3-IPC1
  • MCS-7825-H2-IPC1

  • MCS-7816-I4-IPC1/CCX1
  • MCS-7825-H3-IPC1

  • MCS-7825-I2-IPC1
  • MCS-7825-H4-IPC1

  • MCS-7825-I3-IPC1
  • MCS-7828-H3-IPC1

  • MCS-7825-I4-IPC1
  • MCS-7835-H2-IPC1

  • MCS-7828-I3-SS1
  • MCS-7835-H2-IPC2

  • MCS-7828-I4-SS1
  • DL380G6 (Single E5504 CPU)

  • MCS-7835-I2-IPC1
  • MCS-7845-H2-IPC1

  • MCS-7835-I2-IPC2
  • MCS-7845-H2-IPC2

  • MCS-7835-I3-IPC1
  • DL380G6 (Single E5540 CPU)

  • MCS-7845-I2-IPC1

  • MCS-7845-I2-IPC2

  • MCS-7845-I3-IPC1

Cisco Unified CM release 8.0(2) inapplicable MIBs

IBM-SYSTEM-POWER MIB does not apply to the following IBM server models:

  • MCS-7815-I2-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7816-I4-IPC1/CCX1
  • MCS-7825-I2-IPC1
  • MCS-7825-I3-IPC1
  • MCS-7825-I4-IPC1
  • MCS-7828-I3-SS1
  • MCS-7828-I4-SS1

IBM-SYSTEM-RAID MIB does not apply to the following IBM server models:

  • MCS-7815-I2-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7816-I4-IPC1/CCX1
  • MCS-7825-I4-IPC1
  • MCS-7828-I4-SS1
  • MCS-7835-I3-IPC1
  • MCS-7845-I3-IPC1

IBM-SYSTEM-STORAGE-MIB does not apply to the following IBM server models:

  • MCS-7815-I2-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7816-I4-IPC1/CCX1
  • MCS-7825-I2-IPC1
  • MCS-7825-I3-IPC1
  • MCS-7828-I3-SS1
  • MCS-7835-I2-IPC1
  • MCS-7835-I2-IPC2
  • MCS-7845-I2-IPC1
  • MCS-7845-I2-IPC2

HP CPQSCSI MIB does not apply to the following HP server model:

  • MCS-7816-H3-IPC1
  • MCS-7825-H2-IPC1
  • MCS-7825-H3-IPC1
  • MCS-7825-H4-IPC1
  • MCS-7828-H3-IPC1
  • MCS-7835-H2-IPC1
  • MCS-7835-H2-IPC2
  • DL380G6 (Single E5504 CPU)
  • MCS-7845-H2-IPC1
  • MCS-7845-H2-IPC2
  • DL380G6 (Single E5540 CPU)

Cisco Unified CM release 8.0(1) supported servers

Table 3 Servers available in Cisco Unified CM release 8.0(1)

Cisco Unified CM Release 8.0(1)

IBM Server Models

HP Server Models

  • MCS-7815-I2-IPC11
  • MCS-7816-H3-IPC12
  • MCS-7816-I3-IPC13
  • MCS-7825-H2-IPC14
  • MCS-7816-I4-IPC15
  • MCS-7825-H2-IPC26
  • MCS-7825-I2-IPC17
  • MCS-7825-H3-IPC18
  • MCS-7825-I2-IPC29
  • MCS-7825-H4-IPC110
  • MCS-7825-I3-IPC111
  • MCS-7828-H3
  • MCS-7825-I4-IPC112
  • MCS-7835-H2-IPC113
  • MCS-7828-I3
  • MCS-7835-H2-IPC214
  • MCS-7828-I4
  • MCS-7845-H2-IPC115
  • MCS-7835-I2-IPC116
  • MCS-7845-H2-IPC217
  • MCS-7835-I2-IPC218

  • MCS-7835-I3-IPC119

  • MCS-7845-I2-IPC120

  • MCS-7845-I2-IPC221

  • MCS-7845-I3-IPC122

1 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
2 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
3 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
4 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
5 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
6 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
7 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
8 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
9 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
10 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
11 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
12 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
13 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
14 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
15 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
16 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
17 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
18 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
19 Supported, but note that servers running Cisco Unified Communications Manager (CallManager) 4.0 and later require a minimum of 2 GB of memory for Cisco MCS 7815, MCS 7816, MCS 7825, and MCS 7835 and 4 GB of memory for Cisco MCS 7845.
20 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
21 Supported, but note that Cisco Unified Communications Manager 6.1 and higher requires memory of minimum 2GB for MCS 7815/16/25/35, and 4GB for MCS 7845, and hard drive capacity of 72/80 GB or higher.This will result in mandatory memory and hard drive upgrades, if older supported servers are desired for use with the new software versions.
22 Supported, but note that servers running Cisco Unified Communications Manager (CallManager) 4.0 and later require a minimum of 2 GB of memory for Cisco MCS 7815, MCS 7816, MCS 7825, and MCS 7835 and 4 GB of memory for Cisco MCS 7845.

Note


For information about the product end-of-life notices, go to http:/​/​www.cisco.com/​en/​US/​products/​sw/​voicesw/​ps556/​prod_​eol_​notices_​list.html


Cisco Unified CM release 8.0(1) inapplicable MIBs

IBM-SYSTEM-POWER MIB does not apply to the following IBM server models:

  • MCS-7815-I1-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7815-I3-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7816-I4-IPC1
  • MCS-7825I-3.0-IPC1
  • MCS-7825-I1-IPC1
  • MCS-7825-I2-IPC1
  • MCS-7825-I3-IPC1
  • MCS-7825-I4-IPC1
  • MCS-7828-I3-IPC1

IBM-SYSTEM-RAID MIB does not apply to the following IBM server models:

  • MCS-7815-I1-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7815-I3-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7816-I4-IPC1
  • MCS-7825-I4-IPC1
  • MCS-7828-I4-IPC1

IBM-SYSTEM-STORAGE-MIB does not apply to the following IBM server models:

  • MCS-7815-I1-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7815-I3-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7816-I4-IPC1
  • MCS-7825I-3.0-IPC1
  • MCS-7825-I1-IPC1
  • MCS-7825-I2-IPC1
  • MCS-7825-I3-IPC1
  • MCS-7828-I3-IPC1
  • MCS-7835I-3.0-IPC1
  • MCS-7835-I1-IPC1
  • MCS-7835-I2-IPC1
  • MCS-7835-I2-IPC2
  • MCS-7845I-3.0-IPC1
  • MCS-7845-I1-IPC1
  • MCS-7845-I2-IPC1
  • MCS-7845-I2-IPC2

HP CPQSCSI MIB does not apply to the following HP server model:

  • MCS-7816-H4-IPC1
  • MCS-7825H-3.0-IPC1
  • MCS-7825-H1-IPC1
  • MCS-7825-H2-IPC1
  • MCS-7825-H3-IPC1
  • MCS-7825-H4-IPC1
  • MCS-7828-H3-IPC1
  • MCS-7835H-3.0-IPC1
  • MCS-7835-H1-IPC1
  • MCS-7835-H2-IPC1
  • MCS-7835-H2-IPC2
  • MCS-7845H-3.0-IPC1
  • MCS-7845-H1-IPC1
  • MCS-7845-H2-IPC1
  • MCS-7845-H2-IPC2

HP CPQSM2 MIB does not apply to the following HP server model:

  • MCS-7825H-3.0-IPC1

Cisco Unified CM release 7.1(2) supported servers

Table 4 Servers available in Cisco Unified CM release 7.1(2)

Cisco Unified CM Release 7.1(2)

IBM Server Models

HP Server Models

  • MCS-7815-I1-IPC1
  • MCS-7816-H3-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7816-H4-IPC1/CCX1
  • MCS-7815-I3-IPC1
  • MCS-7825H-3.0-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7825-H1-IPC1
  • MCS-7816-I4-IPC1/CCX1
  • MCS-7825-H2-IPC1
  • MCS-7825I-3.0-IPC1
  • MCS-7825-H3-IPC1
  • MCS-7825-I1-IPC1
  • MCS-7825-H4-IPC1/CCE1/CCX1/ECS1/RC1
  • MCS-7825-I2-IPC1
  • MCS-7828-H3-IPC1
  • MCS-7825-I3-IPC1
  • MCS-7835H-3.0-IPC1
  • MCS-7825-I4-IPC1/CCE1/CCX1/ECS1/RC1
  • MCS-7835-H1-IPC1
  • MCS-7828-I3-IPC1
  • MCS-7835-H2-IPC1
  • MCS-7835I-3.0-IPC1
  • MCS-7835-H2-IPC2/CCE2/CCX2/RC2/ECS2
  • MCS-7835-I1-IPC1
  • MCS-7845H-3.0-IPC1
  • MCS-7835-I2-IPC1
  • MCS-7845-H1-IPC1
  • MCS-7835-I2-IPC2/CCE2/CCX2/RC2/ECS2
  • MCS-7845-H2-IPC1
  • MCS-7845I-3.0-IPC1
  • MCS-7845-H2-IPC2/CCE2/CCX2/RC2/ECS
  • MCS-7845-I1-IPC1

  • MCS-7845-I2-IPC1

  • MCS-7845-I2-IPC2/CCE2/CCX2/RC2/ECS2

Cisco Unified CM release 7.1(2) inapplicable MIBs

IBM-SYSTEM-POWER MIB does not apply to the following IBM server models:

  • MCS-7815-I1-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7815-I3-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7816-I4-IPC1/CCX1
  • MCS-7825I-3.0-IPC1
  • MCS-7825-I1-IPC1
  • MCS-7825-I2-IPC1
  • MCS-7825-I3-IPC1
  • MCS-7825-I4-IPC1/CCE1/CCX1/ECS1/RC1
  • MCS-7828-I3-IPC1

IBM-SYSTEM-RAID MIB does not apply to the following IBM server models:

  • MCS-7815-I1-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7815-I3-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7816-I4-IPC1/CCX1

HP CPQSM2 MIB does not apply to the following HP server model:

  • MCS-7825H-3.0-IPC1

Cisco Unified CM release 7.1(1) supported servers

Table 5 Servers available in Cisco Unified CM release 7.1(1)

Cisco Unified CM Release 7.1(1)

IBM Server Models

HP Server Models

  • MCS-7815-I1-IPC1
  • MCS-7816-H3-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7816-H4-IPC1/CCX1
  • MCS-7815-I3-IPC1
  • MCS-7825H-3.0-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7825-H1-IPC1
  • MCS-7816-I4-IPC1/CCX1
  • MCS-7825-H2-IPC1
  • MCS-7825I-3.0-IPC1
  • MCS-7825-H3-IPC1
  • MCS-7825-I1-IPC1
  • MCS-7825-H4-IPC1/CCE1/CCX1/ECS1/RC1
  • MCS-7825-I2-IPC1
  • MCS-7828-H3-IPC1
  • MCS-7825-I3-IPC1
  • MCS-7835H-3.0-IPC1
  • MCS-7825-I4-IPC1/CCE1/CCX1/ECS1/RC1
  • MCS-7835-H1-IPC1
  • MCS-7828-I3-IPC1
  • MCS-7835-H2-IPC1
  • MCS-7835I-3.0-IPC1
  • MCS-7835-H2-IPC2/CCE2/CCX2/RC2/ECS2
  • MCS-7835-I1-IPC1
  • MCS-7845H-3.0-IPC1
  • MCS-7835-I2-IPC1
  • MCS-7845-H1-IPC1
  • MCS-7835-I2-IPC2/CCE2/CCX2/RC2/ECS2
  • MCS-7845-H2-IPC1
  • MCS-7845I-3.0-IPC1
  • MCS-7845-H2-IPC2/CCE2/CCX2/RC2/ECS2
  • MCS-7845-I1-IPC1

  • MCS-7845-I2-IPC1

  • MCS-7845-I2-IPC2/CCE2/CCX2/RC2/ECS2

Cisco Unified CM release 7.1(1) inapplicable MIBs

IBM-SYSTEM-POWER MIB does not apply to the following IBM server models:

  • MCS-7815-I1-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7815-I3-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7816-I4-IPC1/CCX1
  • MCS-7825I-3.0-IPC1
  • MCS-7825-I1-IPC1
  • MCS-7825-I2-IPC1
  • MCS-7825-I3-IPC1
  • MCS-7825-I4-IPC1/CCE1/CCX1/ECS1/RC1
  • MCS-7828-I3-IPC1

IBM-SYSTEM-RAID MIB does not apply to the following IBM server models:

  • MCS-7815-I1-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7815-I3-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7816-I4-IPC1/CCX1

HP CPQSM2 MIB does not apply to the following HP server model:

  • MCS-7825H-3.0-IPC1

Cisco Unified CM release 7.0(1) supported servers

Table 6 Servers available in Cisco Unified CM release 7.0(1)

Cisco Unified CM Release 7.0(1)

IBM Server Models

HP Server Models

  • MCS-7815-I1-IPC1
  • MCS-7816-H3-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7825H-3.0-IPC1
  • MCS-7815-I3-IPC1
  • MCS-7825-H1-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7825-H2-IPC1
  • MCS-7825I-3.0-IPC1
  • MCS-7825-H3-IPC1
  • MCS-7825-I1-IPC1
  • MCS-7828-H3-IPC1
  • MCS-7825-I2-IPC1
  • MCS-7835H-3.0-IPC1
  • MCS-7825-I3-IPC1
  • MCS-7835-H1-IPC1
  • MCS-7828-I3-IPC1
  • MCS-7835-H2-IPC1
  • MCS-7835I-3.0-IPC1
  • MCS-7845H-3.0-IPC1
  • MCS-7835-I1-IPC1
  • MCS-7845-H1-IPC1
  • MCS-7835-I2-IPC1/IPC2
  • MCS-7845-H2-IPC1
  • MCS-7845I-3.0-IPC1

  • MCS-7845-I1-IPC1

  • MCS-7845-I2-IPC1/IPC2

  • MCS-7815-I1-IPC1


Note


IBM Model MCS-7835I-2.4-EVV1 is discontinued in this release.



Note


HP MCS-7825H-2.2-EVV1, MCS-7835H-2.4-EVV1, and MCS-7845H-2.4-EVV1 are discontinued in this release.


Cisco Unified CM release 7.0(1) MIB unsupported servers

IBM-SYSTEM-POWER MIB does not apply to the following IBM server models:

  • MCS-7815-I1-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7815-I3-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7825I-3.0-IPC1
  • MCS-7825-I1-IPC1
  • MCS-7825-I2-IPC1
  • MCS-7825-I3-IPC1
  • MCS-7828-I3-IPC1

IBM-SYSTEM-RAID MIB does not apply to the following IBM server models:

  • MCS-7815-I1-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7815-I3-IPC1
  • MCS-7816-I3-IPC1

HP CPQSM2 MIB does not apply to the following HP server model:

  • MCS-7825H-3.0-IPC1

Cisco Unified CM release 6.1(3) supported servers

Table 7 Servers available in Cisco Unified CM release 6.1(3)

Cisco Unified CM Release 6.1(3)

IBM Server Models

HP Server Models

  • MCS-7815-I1-IPC1
  • MCS-7816-H3-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7825H-2.2-EVV1
  • MCS-7815-I3-IPC1
  • MCS-7825H-3.0-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7825-H1-IPC1
  • MCS-7825I-3.0-IPC1
  • MCS-7825-H2-IPC1
  • MCS-7825-I1-IPC1
  • MCS-7825-H3-IPC1
  • MCS-7825-I2-IPC1
  • MCS-7828-H3-IPC1
  • MCS-7825-I3-IPC1
  • MCS-7828-H4-BE
  • MCS-7828-I3-IPC1
  • MCS-7835H-2.4-EVV1
  • MCS-7828-I4-BE
  • MCS-7835H-3.0-IPC1
  • MCS-7835I-2.4-EVV1
  • MCS-7835-H1-IPC1
  • MCS-7835I-3.0-IPC1
  • MCS-7835-H2-IPC1
  • MCS-7835-I1-IPC1
  • MCS-7845H-2.4-EVV1
  • MCS-7835-I2-IPC1/IPC2
  • MCS-7845H-3.0-IPC1
  • MCS-7845I-3.0-IPC1
  • MCS-7845-H1-IPC1
  • MCS-7845-I1-IPC1
  • MCS-7845-H2-IPC1
  • MCS-7845-I2-IPC1/IPC2

Cisco Unified CM release 6.1(3) MIB unsupported servers

IBM-SYSTEM-POWER MIB does not apply to the following IBM server models:

  • MCS-7815-I1-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7815-I3-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7825I-3.0-IPC1
  • MCS-7825-I1-IPC1
  • MCS-7825-I2-IPC1
  • MCS-7825-I3-IPC1
  • MCS-7828-I3-IPC1
  • MCS-7828-I4-BE

IBM-SYSTEM-RAID MIB does not apply to the following IBM server models:

  • MCS-7815-I1-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7815-I3-IPC1
  • MCS-7816-I3-IPC1

HP CPQSCSI MIB does not apply to the following HP server models:

  • MCS-7816-H3-IPC1
  • MCS-7825H-2.2-EVV1
  • MCS-7825H-3.0-IPC1
  • MCS-7825-H1-IPC1
  • MCS-7825-H2-IPC1
  • MCS-7825-H3-IPC1
  • MCS-7828-H3-IPC1
  • MCS-7828-H4-BE
  • MCS-7835H-2.4-EVV1
  • MCS-7835H-3.0-IPC1
  • MCS-7835-H1-IPC1
  • MCS-7835-H2-IPC1
  • MCS-7845H-2.4-EVV1
  • MCS-7845H-3.0-IPC1
  • MCS-7845-H1-IPC1
  • MCS-7845-H2-IPC1

HP CPQSM2 MIB does not apply to the following HP server models:

  • MCS-7825H-2.2-EVV1
  • MCS-7825H-3.0-IPC1

Cisco Unified CM release 6.1 supported servers

Table 8 Servers available in Cisco Unified CM release 6.1

Cisco Unified CM Release 6.1

IBM Server Models

HP Server Models

  • MCS-7815-I1-IPC1
  • MCS-7816-H3-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7825H-2.2-EVV1
  • MCS-7815-I3-IPC1
  • MCS-7825H-3.0-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7825-H1-IPC1
  • MCS-7825I-3.0-IPC1
  • MCS-7825-H2-IPC1
  • MCS-7825-I1-IPC1
  • MCS-7825-H3-IPC1
  • MCS-7825-I2-IPC1
  • MCS-7828-H3-IPC1
  • MCS-7825-I3-IPC1
  • MCS-7835H-2.4-EVV1
  • MCS-7828-I3-IPC1
  • MCS-7835H-3.0-IPC1
  • MCS-7835I-2.4-EVV1
  • MCS-7835-H1-IPC1
  • MCS-7835I-3.0-IPC1
  • MCS-7835-H2-IPC1
  • MCS-7835-I1-IPC1
  • MCS-7845H-2.4-EVV1
  • MCS-7835-I2-IPC1/IPC2
  • MCS-7845H-3.0-IPC1
  • MCS-7845I-3.0-IPC1
  • MCS-7845-H1-IPC1
  • MCS-7845-I1-IPC1
  • MCS-7845-H2-IPC1
  • MCS-7845-I2-IPC1/IPC2

Cisco Unified CM release 6.1 MIB unsupported servers

IBM-SYSTEM-POWER MIB does not apply to the following IBM server models:

  • MCS-7815-I1-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7815-I3-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7825I-3.0-IPC1
  • MCS-7825-I1-IPC1
  • MCS-7825-I2-IPC1
  • MCS-7825-I3-IPC1
  • MCS-7828-I3-IPC1

IBM-SYSTEM-RAID MIB does not apply to the following IBM server models:

  • MCS-7815-I1-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7815-I3-IPC1
  • MCS-7816-I3-IPC1

HP CPQSCSI MIB does not apply to the following HP server models:

  • MCS-7816-H3-IPC1
  • MCS-7825H-2.2-EVV1
  • MCS-7825H-3.0-IPC1
  • MCS-7825-H1-IPC1
  • MCS-7825-H2-IPC1
  • MCS-7825-H3-IPC1
  • MCS-7828-H3-IPC1
  • MCS-7828-H4-BE
  • MCS-7835H-2.4-EVV1
  • MCS-7835H-3.0-IPC1
  • MCS-7835-H1-IPC1
  • MCS-7835-H2-IPC1
  • MCS-7845H-2.4-EVV1
  • MCS-7845H-3.0-IPC1
  • MCS-7845-H1-IPC1
  • MCS-7845-H2-IPC1

HP CPQSM2 MIB does not apply to the following HP server models:

  • MCS-7825H-2.2-EVV1
  • MCS-7825H-3.0-IPC1

Cisco Unified CM release 6.0 supported servers

Table 9 Servers available in Cisco Unified CM release 6.0

Cisco Unified CM Release 6.0

IBM Server Models

HP Server Models

Dell Server Models

  • MCS-7815-I1-IPC1
  • MCS-7816-H3-IPC1
  • PE2950
  • MCS-7815-I2-IPC1
  • MCS-7825H-2.2-EVV1
  • MCS-7816-I3-IPC1
  • MCS-7825H-3.0-IPC1
  • MCS-7825I-3.0-IPC1
  • MCS-7825-H1-IPC1
  • MCS-7825-I1-IPC1
  • MCS-7825-H2-IPC1
  • MCS-7825-I2-IPC1
  • MCS-7825-H3-IPC1
  • MCS-7828-I3-IPC1
  • MCS-7828-H3-IPC1
  • MCS-7835I-2.4-EVV1
  • MCS-7835H-2.4-EVV1
  • MCS-7835I-3.0-IPC1
  • MCS-7835H-3.0-IPC1
  • MCS-7835-I1-IPC1
  • MCS-7835-H1-IPC1
  • MCS-7835-I2-IPC1
  • MCS-7835-H2-IPC1
  • MCS-7845I-3.0-IPC1
  • MCS-7845H-2.4-EVV1
  • MCS-7845-I1-IPC1
  • MCS-7845H-3.0-IPC1
  • MCS-7845-I2-IPC1
  • MCS-7845-H1-IPC1
  • MCS-7825-I3-IPC1
  • MCS-7845-H2-IPC1

Cisco Unified CM release 6.0 MIB unsupported servers

IBM-SYSTEM-POWER (UMSPOWER) MIB does not apply to the following IBM server models:

  • MCS-7815-I1-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7816-I3-IPC1
  • MCS-7825I-3.0-IPC1
  • MCS-7825-I1-IPC1
  • MCS-7825-I2-IPC1
  • MCS-7825-I3-IPC1
  • MCS-7828-I3-IPC1

IBM-SERVERAID MIB does not apply to the following IBM server models:

  • MCS-7815-I1-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7825I-3.0-IPC1
  • MCS-7825-I1-IPC1
  • MCS-7825-I2-IPC1
  • MCS-7835-I2-IPC1
  • MCS-7845-I2-IPC1

IBM-SYSTEM-RAID MIB does not apply to the following IBM server models:

  • MCS-7815-I1-IPC1
  • MCS-7815-I2-IPC1
  • MCS-7816-I3-IPC1

HP CPQSCSI MIB does not apply to the following HP server models:

  • MCS-7816-H3-IPC1
  • MCS-7825H-2.2-EVV1
  • MCS-7825H-3.0-IPC1
  • MCS-7825-H1-IPC1
  • MCS-7825-H2-IPC1
  • MCS-7825-H3-IPC1
  • MCS-7828-H3-IPC1
  • MCS-7835H-2.4-EVV1
  • MCS-7835H-3.0-IPC1
  • MCS-7835-H1-IPC1
  • MCS-7835-H2-IPC1
  • MCS-7845H-2.4-EVV1
  • MCS-7845H-3.0-IPC1
  • MCS-7845-H1-IPC1
  • MCS-7845-H2-IPC1

HP CPQSM2 MIB does not apply to the following HP server models:

  • MCS-7825H-2.2-EVV1
  • MCS-7825H-3.0-IPC1

IBM MIBs

Table 10 IBM MIBs

MIB

OID

Function

Supported for browsing only

IBM-SYSTEM-HEALTH-MIB

1.3.6.1.4.1.2.6.159.1.1.30

Provides temperature, voltage, and fan status

IBM-SYSTEM-ASSETID-MIB

1.3.6.1.4.1.2.6.159.1.1.60

Provides hardware component asset data

IBM-SYSTEM-LMSENSOR-MIB

1.3.6.1.4.1.2.6.159.1.1.80

Provides temperature, voltage, and fan details

IBM-SYSTEM-NETWORK-MIB

1.3.6.1.4.1.2.6.159.1.1.110

Provides Network Interface Card (NIC) status

IBM-SYSTEM-MEMORY-MIB

1.3.6.1.4.1.2.6.159.1.1.120

Provides physical memory details

IBM-SYSTEM-POWER-MIB

1.3.6.1.4.1.2.6.159.1.1.130

Provides power supply details

IBM-SYSTEM-PROCESSOR-MIB

1.3.6.1.4.1.2.6.159.1.1.140

Provides CPU asset/status data

Supported for system traps

IBM-SYSTEM-TRAP

1.3.6.1.4.1.2.6.159.1.1.0

Provides temperature, voltage, fan, disk, NIC, memory, power supply, and CPU details

IBM-SERVERAID-MIB

1.3.6.1.4.1.2.6.167.2

Provides RAID status

IBM-SYSTEM-RAID-MIB

1.3.6.1.4.1.2.6.159.1.1.200.1

Provides RAID status

IBM-SYSTEM-STORAGE-MIB

1.3.6.1.4.1.2.6.159.3.1

Provides RAID status

IBM hardware status messages

Table 11 IBM hardware status messages, MIBs and objects names, and object responses

Cisco Unified CM Release 6.x

MCS-78xx Status

MIBS and Object Names

Object Responses

System Fan

IBM-SYSTEM-LMSENSOR-MIB::ibmSystem TachometerStatus (also see ibmSystemTachometerKeyIndex)

This is a string indicating the current status of the object. Various operational and non-operational statuses can be defined.

Operational statuses are OK, Degraded and Pred Fail. Pred Fail indicates that an element may be functioning properly but predicting a failure in the near future. An example is a SMART-enabled hard drive.

Non-operational statuses are Error, Starting, Stopping and Service. Service can apply during mirror-resilvering of a disk, reload of a user permissions list, or other administrative work.

Not all such work is on-line, yet the managed element is neither OK nor in one of the other states.

OK = Normal; Error = Critical

Voltage Sensor

IBM-SYSTEM-LMSENSOR-MIB::ibmSystem VoltageSensorStatus (also see ibmSystemVoltageSensorKeyIndex)

This is a string indicating the current status of the object. Various operational and non-operational statuses can be defined.

Operational statuses are OK, Degraded and Pred Fail. Pred Fail indicates that an element may be functioning properly but predicting a failure in the near future. An example is a SMART-enabled hard drive.

Non-operational statuses are Error, Starting, Stopping and Service. Service can apply during mirror-resilvering of a disk, reload of a user permissions list, or other administrative work. Not all such work is on-line, yet the managed element is neither OK nor in one of the other states.

OK = Normal; Error = Critical

Thermal

IBM-SYSTEM-LMSENSOR-MIB::ibmSystem TemperatureSensorStatus (also see ibmSystemTemperatureSensorKeyIndex)

The Status property is a string indicating the current status of the object. Various operational and non-operational statuses can be defined. Operational statuses are OK, Degraded and Pred Fail. Pred Fail indicates that an element may be functioning properly but predicting a failure in the near future. An example is a SMART-enabled hard drive. Non-operational statuses can also be specified. These are Error, Starting, Stopping and Service. The latter, Service, could apply during mirror-resilvering of a disk, reload of a user permissions list, or other administrative work. Not all such work is on-line, yet the managed element is neither OK nor in one of the other states. OK = Normal; Error = Critical

Network Interface Card

IBM-SYSTEM-NETWORK-MIB::ibmSystem LogicalNetworkAdapterStatus (also see ibmSystemLogicalNetworkAdapterKeyIndex)

The online status of the adapter.

Logical Drive

IBM-SYSTEM-TRAP-MIB::ibmSystem RaidLogicalDriveStatus (also see ibmSystemRaidLogicalDriveKeyIndex)

The status of the logical drive

Physical Drive

IBM-SYSTEM-TRAP-MIB::ibmSystem RaidDiskDriveStatus & ibmSystemRaidControllerStatus (also see ibmSystemRaidDiskDriveKeyIndex & ibmSystemRaidControllerKeyIndex)

Hewlett Packard MIBs

Table 12 HP MIBs

MIB

OID

Function

Supported for browsing and system traps

CPQSTDEQ-MIB

1.3.6.1.4.1.232.1

Provides hardware component configuration data

CPQSINFO-MIB

1.3.6.1.4.1.232.2

Provides hardware component asset data

CPQIDA-MIB

1.3.6.1.4.1.232.3

Provides RAID status/events

CPQHLTH-MIB

1.3.6.1.4.1.232.6

Provides hardware components status/events

CPQSTSYS-MIB

1.3.6.1.4.1.232.8

Provides storage (disk) systems status/events

CPQSM2-MIB

1.3.6.1.4.1.232.9

Provides iLO status/events

CPQTHRSH-MIB

1.3.6.1.4.1.232.10

Provides alarm threshold management

CPQHOST-MIB

1.3.6.1.4.1.232.11

Provides operating system information

CPQIDE-MIB

1.3.6.1.4.1.232.14

Provides IDE (CD-ROM) drive status/events

CPQNIC-MIB

1.3.6.1.4.1.232.18

Provides Network Interface Card (NIC) status/events

HP hardware status messages

The following table lists status messages, MIBs and OIDs, MIB object names and clearing values, and object responses.

Table 13 HP hardware status messages, MIBs and OIDs, MIB object names and clearing values, and object responses

Cisco Unified CM Release 6.x

MCS-78xx Status

MIB and OID

MIB Object Name and Clearing Value

Object Response

Logical Drive23

CPQIDA-MIB1.3.6.1.4.1.232.3.2.3.1.1.4

cpqDaLogDrvStatus

Clearing Value = 2

The logical drive can be in one of the following states:

  • Ok (2) Indicates that the logical drive is in normal operation mode.
  • Failed (3) Indicates that more physical drives have failed than the fault tolerance mode of the logical drive can handle without data loss.
  • Unconfigured (4) Indicates that the logical drive is not configured.
  • Recovering (5) Indicates that the logical drive is using Interim Recovery Mode. In Interim Recovery Mode, at least one physical drive has failed, but the logical drive's fault tolerance mode lets the drive continue to operate with no data loss.
  • Ready Rebuild (6) Indicates that the logical drive is ready for Automatic Data Recovery. The physical drive that failed has been replaced, but the logical drive is still operating in Interim Recovery Mode.
  • Rebuilding (7) Indicates that the logical drive is currently doing Automatic Data Recovery. During Automatic Data Recovery, fault tolerance algorithms restore data to the replacement drive.
  • Wrong Drive (8) Indicates that the wrong physical drive was replaced after a physical drive failure.
  • Bad Connect (9) Indicates that a physical drive is not responding.

Physical Drive1

CPQIDA-MIB1.3.6.1.4.1.232.3.2.5.1.1.6

cpqDaPhyDrv Status

Clearing Value = 2

  • The following values are valid for the physical drive status:
  • other (1) Indicates that the instrument agent does not recognize the drive. You may need to upgrade your instrument agent and/or driver software.
  • ok (2) Indicates the drive is functioning properly.
  • failed (3) Indicates that the drive is no longer operating and should be replaced.
  • predictiveFailure(4) Indicates that the drive has a predictive failure error and should be replaced.

System Fan

CPQHLTH-MIB1.3.6.1.4.1.232.6.2.6.4

cpqHeThermalSystemFan Status

Clearing Value = 2

This value will be one of the following:

  • other(1) Fan status detection is not supported by this system or driver.
  • ok(2) The fan is operating properly.
  • degraded(2) A redundant fan is not operating properly.
  • failed(4) A non-redundant fan is not operating properly.

CPU Fan

CPQHLTH-MIB1.3.6.1.4.1.232.6.2.6.5

cpqHeThermalCpuFan Status

Clearing Value = 2

This value will be one of the following:

  • other(1) Fan status detection is not supported by this system or driver.
  • ok(2) The fan is operating properly.
  • degraded(2) A redundant fan is not operating properly.
  • failed(4) A non-redundant fan is not operating properly.

Network Interface Card (NIC)

CPQNIC-MIB1.3.6.1.4.1.232.18.2.3.1.1.13

cpqNicIfPhysAdapterState

Clearing Value = 2 and 3

The following values are valid—

  • unknown(1) The instrument agent was not able to determine the status of the adapter. The instrument agent may need to be upgraded.
  • ok(2) The physical adapter is operating properly.
  • generalFailure(3) The physical adapter has failed.
  • linkFailure(4) The physical adapter has lost link. Check the cable connections to this adapter.

Thermal

CPQHLTH-MIB1.3.6.1.4.1.232.6.2.6.1

cpqHeThermalCondition

Clearing Value = 2

This value will be one of the following:

  • other(1) Temperature could not be determined.
  • ok(2) The temperature sensor is within normal operating range.
  • degraded(3) The temperature sensor is outside of normal operating range.
  • failed(4) The temperature sensor detects a condition that could permanently damage the system.
Note   

The system automatically shuts down if the failed (4) condition occurs, so it is unlikely that 4 will ever be returned by the agent. If the cpqHeThermalDegradedAction is set to shut down (3), the system will shut down if the condition occurs.

Power Supply1

CPQHLTH-MIB1.3.6.1.4.1.232.6.2.9.3.1.5

cpqHeFltTolPowerSupply Status

Clearing Value = 1

This value will be one of the following:

  • other(1) The status could not be determined or not present.
  • ok(2) The power supply is operating normally.
  • degraded(3) A temperature sensor, fan or other power supply component is outside of normal operating range.
  • failed(4) A power supply component detects a condition that could permanently damage the system.

NIC Errors

CPQNIC-MIB1.3.6.1.4.1.232.18.2.3.1.1.16

cpqNicIfPhysAdapterGood Transmits

Clearing Value = <0.5% for 1 hour

Interface is experiencing excessive errors

1.3.6.1.4.1.232.18.2.3.1.1.18

cpqNicIfPhysAdapterBad Transmits

1.3.6.1.4.1.232.18.2.3.1.1.17

cpqNicIfPhysAdapterGood Receives

1.3.6.1.4.1.232.18.2.3.1.1.19

cpqNicIfPhysAdapterBad Receives

NIC Utilization

CPQNIC-MIB1.3.6.1.4.1.232.18.2.3.1.1.16

cpqNicIfPhysAdapterGood Transmits

Clearing Value = <50% for 1 hour

Interface is experiencing High Utilization

1.3.6.1.4.1.232.18.2.3.1.1.18

cpqNicIfPhysAdapterBad Transmits

1.3.6.1.4.1.232.18.2.3.1.1.17

cpqNicIfPhysAdapterGood Receives

1.3.6.1.4.1.232.18.2.3.1.1.19

cpqNicIfPhysAdapterBad Receives

Memory Module Trap

1.3.6.1.4.1.232.6.3

cpqHe4CorrMemReplace MemModule

See CPQHOST-MIB for information on the following trap variables:

  • sysName
  • cpqHoTrapFlags
  • cpqHeResMemBoardIndex
  • cpqHeResMemModuleIndex
  • cpqHeResMemModuleSpare PartNo
  • cpqSiMemModuleSize
  • cpqSiServerSystemId

Trap number is 6056 which replaces 6029.

A correctable memory log entry indicates a memory module needs to be replaced. The errors have been corrected, but the memory module should be replaced. The error information is reported in the variable cpqHeCorrMemErrDesc

78x5-H Insite Manager Service

HOST-RESOURCES-MIB1.3.6.1.2.1.25.4.2.1.2

cmaeventd

Compaq Insite Manager Service Failure

cmafcad

cmahealthd

cmahostd

Positive String ID forcmaidad

cmaided

cmanicd

cmapeerd

cmaperfd

cmasm2d

cmastdeqd

cmathreshd

23
24

Intel MIBs

The following table lists Intel MIBs, OID, and functions.

Table 14 Intel MIBs

MIB

OID

Function

Supported for browsing and system traps

INTEL-SERVER-BASEBOARD6

1.3.6.1.4.1.343.2.10.3.6.200

Denotes the power group and describes voltage probes, status, and readings

1.3.6.1.4.1.343.2.10.3.6.300

Denotes the thermal group and describes cooling devices, fans, and temperature probes

1.3.6.1.4.1.343.2.10.3.6.10

Denotes the instances of cooling devices

1.3.6.1.4.1.343.2.10.3.6.20

Denotes the status, reading, and threshold for every cooling device and fan

1.3.6.1.4.1.343.2.10.3.6.30

Denotes the instances of temperature probes

1.3.6.1.4.1.343.2.10.3.6.40

Denotes the status, reading, thresholds for every temperature probe

1.3.6.1.4.1.343.2.10.3.6.1000

Denotes the events group and describes power, thermal, and system events

Related References

Intel hardware status messages

The following table lists status messages, MIBs and OIDs, MIB object names and clearing values, and object responses.

Table 15 Intel hardware status messages, MIBs and objects names, and object responses

Cisco Unified CM Release 7.x

MCS-78xx Status

MIBS and Object Names

Object Responses

Power

INTEL-SERVER-BASEBOARD6::powerEvents

System

INTEL-SERVER-BASEBOARD6::systemEvents

Thermal

INTEL-SERVER-BASEBOARD6::thermalEvents

24 Unavailable for MCS-7825H