Cisco Unified Communications Operating System Administration Guide, Release 9.1(1)
Settings
Downloads: This chapterpdf (PDF - 1.23MB) The complete bookPDF (PDF - 3.24MB) | Feedback

Settings

Settings

You can view and update the following operating system settings:

  • IP—the IP addresses and Dynamic Host Configuration Protocol (DHCP) client settings that were entered when the application was installed.
  • SMTP—the SMTP host that the operating system uses for sending email notifications.

This section also describes how to change time settings and correct time zone data.

IP settings

Change Ethernet settings

You can determine whether Dynamic Host Configuration Protocol (DHCP) is active and locate the related Ethernet IP addresses, as well as the IP address for the network gateway.

Before You Begin
  • All Ethernet settings apply only to Eth0. You cannot configure any settings for Eth1. The Maximum Transmission Unit (MTU) on Eth0 defaults to 1500.
  • Changing the Ethernet settings causes an immediate system restart.
Procedure
    Step 1   Sign in to Cisco Unified IM and Presence Operating System Administration.
    Step 2   Select Settings > IP > Ethernet.
    Step 3   Enter the new values in the appropriate fields to modify the Ethernet settings, and then select Save.
    Table 1 Ethernet Settings Fields and Descriptions

    Field

    Description

    DHCP

    Indicates whether DHCP is Enabled or Disabled.

    Hostname

    Shows the name of the host node.

    Note   

    You can only change the hostname after changes to these configuration settings are complete:

    • DNS
    • Cisco Unified Communications Manager Application Server List
    • IM and Presence Topology

    IP Address

    Shows the IP address of the system.

    Note   

    Changing the IP address or host on the IM and Presence database publisher node can affect system performance.

    Subnet Mask

    Shows the IP subnet mask address.

    Default Gateway

    Shows the IP address of the network gateway.

    Troubleshooting Tips

    If you enable DHCP, the system disables the Port and Gateway setting and it cannot be changed.


    Change publisher node IP address on subscriber nodes

    If, for network configuration purposes, you changed the IP address or hostname on the IM and Presence Service database publisher node, then you will need to update the IP address of the IM and Presence Service database publisher node on IM and Presence Service subscriber nodes.

    Before You Begin

    Use this functionality only if you want an IM and Presence Service subscriber node to point to a different IM and Presence Service database publisher node. If this node is the IM and Presence Service database publisher node, be aware that you cannot use this window to change the IP address.

    Procedure
      Step 1   Sign in to Cisco Unified IM and Presence Operating System Administration.
      Step 2   Select Settings > IP > Publisher.
      Step 3   Enter the new IM and Presence Service database publisher node IP address.
      Step 4   (Optional) Enter a new IM and Presence Service database publisher node name.
      Step 5   (Optional) Following a fresh installation of IM and Presence Service, you can change the IP address of the Cisco Unified Communications Manager publisher node. Select System > CUCM Publisher in Cisco Unified Communications Manager IM and Presence Administration.

      Troubleshoot publisher node IP address change on subscriber node

      Before You Begin

      If the IP address of the IM and Presence database publisher node changes while an IM and Presence subscriber node is offline, be aware that you may not be able to sign in to Cisco Unified Communications Manager IM and Presence Administration on the IM and Presence subscriber node. Complete this procedure if IM and Presence does not function properly.

      Procedure
        Step 1   Sign in directly to Cisco Unified IM and Presence Operating System Administration on the subsequent node by using the following URL:http://node-name/cmplatform where node-name specifies the hostname or IP address of the IM and Presence subscriber node.
        Step 2   Enter your Administrator user name and password and select Submit.
        Step 3   Select Settings > IP > Publisher.
        Step 4   Enter the new IP address for the IM and Presence database publisher node and select Save.
        Step 5   Restart the IM and Presence subscriber node.

        NTP settings

        By design, you cannot configure or change the NTP server following a fresh installation of the IM and Presence Service.

        Change SMTP settings

        Before You Begin

        You must configure an SMTP host if you want the system to send you email, for example, from the Certificate Expiry Monitor.

        Procedure
          Step 1   Sign in to Cisco Unified IM and Presence Operating System Administration.
          Step 2   Select Settings > SMTP.
          Step 3   Enter or modify the SMTP hostname or IP address.

          Change time settings

          You can manually configure the node time if NTP is currently disabled.

          Before You Begin

          Before you can manually configure the node time, you must delete any NTP servers that you have configured.

          Procedure
            Step 1   Sign in to Cisco Unified IM and Presence Operating System Administration.
            Step 2   Select Settings > Time.
            Step 3   Enter the date and time for the system.

            Related Information

            Correct time zone data

            The IM and Presence Service includes the latest time zone information and Cisco contacts you about major time zone events. After you install the IM and Presence Service, you can download a COP file with the latest updates. For more information on how to correctly upgrade your time zone data, see the Release Notes for Cisco Unified Communications Manager on Cisco.com.