Cisco Unified Communications Manager Administration Guide, Release 8.5(1)
SIP Route Pattern Configuration
Downloads: This chapterpdf (PDF - 108.0KB) The complete bookPDF (PDF - 13.86MB) | Feedback

SIP Route Pattern Configuration

Table Of Contents

SIP Route Pattern Configuration

SIP Route Pattern Configuration Settings

Related Topics


SIP Route Pattern Configuration


This section contains information on the following topics:

SIP Route Pattern Configuration Settings

Related Topics

SIP Route Pattern Configuration Settings

In Cisco Unified Communications Manager Administration, use the Call Routing > SIP Route Pattern menu path to configure SIP route patterns.

Cisco Unified Communications Manager uses SIP route patterns to route or block both internal and external calls.

The domain name or IP address provides the basis for routing. The administrator can add domains, IP addresses, and IP network (subnet) addresses and associate them to SIP trunks (only). This method allows requests that are destined for these domains to be routed through particular SIP trunk interfaces.


Note Because no default SIP route patterns exist in Cisco Unified Communications Manager, the administrator must set them up.

Domain name examples: cisco.com, my-pc.cisco.com, *.com, rtp-ccm[1-5].cisco.com

Valid characters for domain names: [, -, ., 0-9, A-Z, a-z, *, and ].

IPv4 address examples: 172.18.201.119 or 172.18.201.119/32 (explicit IP host address); 172.18.0.0/16 (IP subnet); 172.18.201.18/21 (IP subnet).

Valid characters for IP addresses: 0-9, ., and /


Tips About Configuring SIP Route Patterns

Before you begin, ensure at least one SIP Profile and SIP trunk are configured before you can configure a SIP route pattern. See the "Configuring a Trunk" section on page 68-60.

Tips About Deleting SIP Route Patterns

If the SIP route pattern is not in use, Cisco Unified Communications Manager deletes it. If it is in use, a message displays.

Using the GUI

For instructions on how to use the Cisco Unified Communications Manager Administration Graphical User Interface (GUI) to find, delete, configure, or copy records, see the "Navigating the Cisco Unified Communications Manager Administration Application" section on page 1-13 and its subsections, which explain how to use the GUI and detail the functions of the buttons and icons.

Configuration Settings Table

Table 37-1 describes the SIP route pattern configuration settings. For related procedures, see the "Related Topics" section.

Table 37-1 SIP Route Pattern Configuration Settings 

Field
Description
Pattern Definition

Pattern Usage

(Required) From the drop-down list, choose either Domain Routing or IP Address Routing.

IPv4 Pattern

(Required) Enter the domain, sub-domain, IPv4 address, or IP subnetwork address.

Tip If the SIP trunk supports IPv6 or both IPv4 and IPv6 (dual-stack mode), configure the IPv6 Pattern in addition to the IPv4 pattern.

Note For the IP subnetwork address, in Classless Inter-Domain Routing (CIDR) notation, X.X.X.X/Y; where Y is the network prefix that denotes the number of bits in the address that will be the network address.

IPv6 Pattern

Cisco Unified Communications Manager uses SIP route patterns to route or block both internal and external calls. The IPv6 address in this field provides the basis for routing internal and external calls to SIP trunks that support IPv6.

Tip If the SIP trunk supports IPv6 or both IPv4 and IPv6 (dual-stack mode), configure the IPv4 Pattern in addition to the IPv6 Pattern.

Description

For this optional entry, enter a description of the SIP Route Pattern. The description can include up to 50 characters in any language, but it cannot include double-quotes ("), percentage sign (%), ampersand (&), or angle brackets (<>).

Route Partition

If you want to use a partition to restrict access to the SIP route pattern, choose the desired partition from the drop-down list box. If you do not want to restrict access to the SIP route pattern, choose <None> for the partition. See the "Partition Configuration" section on page 40-1 for more information on how to use partitions.

You can configure the number of partitions that display in this drop-down list box by using the Max List Box Items enterprise parameter. If more than 250 partitions are specified by using the Max List Box Items enterprise parameter, the Find button displays next to the drop-down list box. Click the Find button to display the Select Partition window. Enter a partial partition name in the List items where Name contains field. Click the desired partition name in the list of partitions that displays in the Select item to use box and click Add Selected.

Note To set the maximum list box items, choose System > Enterprise Parameters and choose CCMAdmin Parameters.

Note Make sure that the combination of SIP route pattern, route filter, and partition is unique within the Cisco Unified Communications Manager cluster.

 

SIP Trunk

(Required) Use the drop-down list to choose the SIP trunk to which the SIP route pattern should be associated.

Block Pattern

If you do not want this pattern to be used for routing calls, click the Block Pattern check box.

Calling Party Transformations

Use Calling Party's External Phone Mask

Check the check box if you want the full, external phone number to be used for calling line identification (CLID) on outgoing calls. You may also configure an External Phone Number Mask on all phone devices.

Calling Party Transformation Mask

Enter a transformation mask value. Valid entries include the digits 0 through 9 and the wildcard characters X, asterisk (*), and octothorpe (#). If this field is blank and the preceding field is not checked, no calling party transformation takes place. See the "Calling Party Number Transformations Settings" section in the Cisco Unified Communications Manager System Guide for more information.

Prefix Digits (Outgoing Calls

Enter prefix digits in the Prefix Digits (Outgoing Calls) field. Valid entries include the digits 0 through 9 and the wildcard characters asterisk (*) and octothorpe (#).

Note The appended prefix digit does not affect which directory numbers route to the assigned device.

Calling Line ID Presentation

Cisco Unified Communications Manager uses calling line ID presentation (CLIP/CLIR) as a supplementary service to allow or restrict the originating caller phone number on a call-by-call basis.

Choose whether you want the Cisco Unified Communications Manager to allow or restrict the display of the calling party phone number on the called party phone display for this SIP route pattern.

Choose Default if you do not want to change calling line ID presentation. Choose Allowed if you want Cisco Unified Communications Manager to allow the display of the calling number. Choose Restricted if you want Cisco Unified Communications Manager to block the display of the calling number.

For more information about this field, see Table 16-8 in the "Calling Party Number Transformations Settings" section in the Cisco Unified Communications Manager System Guide.

Calling Line Name Presentation

Cisco Unified Communications Manager uses calling name presentation (CNIP/CNIR) as a supplementary service to allow or restrict the originating caller name on a call-by-call basis.

Choose whether you want the Cisco Unified Communications Manager to allow or restrict the display of the calling party name on the called party phone display for this SIP route pattern.

Choose Default if you do not want to change calling name presentation. Choose Allowed if you want Cisco Unified Communications Manager to display the calling name information. Choose Restricted if you want Cisco Unified Communications Manager to block the display of the calling name information.

For more information about this field, see Table 16-8 in the "Calling Party Number Transformations Settings" section in the Cisco Unified Communications Manager System Guide.

Connected Party Transformations

Connected Line ID Presentation

Cisco Unified Communications Manager uses connected line ID presentation (COLP/COLR) as a supplementary service to allow or restrict the called party phone number on a call-by-call basis.

Choose whether you want Cisco Unified Communications Manager to allow or restrict the display of the connected party phone number on the calling party phone display for this SIP route pattern.

Choose Default if you do not want to change the connected line ID presentation. Choose Allowed if you want to display the connected party phone number. Choose Restricted if you want Cisco Unified Communications Manager to block the display of the connected party phone number.

For more information about this field, see Table 16-11 in the "Connected Party Presentation and Restriction Settings" section in the Cisco Unified Communications Manager System Guide.

Connected Line Name Presentation

Cisco Unified Communications Manager uses connected name presentation (CONP/CONR) as a supplementary service to allow or restrict the called party name on a call-by-call basis.

Choose whether you want Cisco Unified Communications Manager to allow or restrict the display of the connected party name on the calling party phone display for this SIP route pattern.

Choose Default if you do not want to change the connected name presentation. Choose Allowed if you want to display the connected party name. Choose Restricted if you want Cisco Unified Communications Manager to block the display of the connected party name.

For more information about this field, see Table 16-11 in the "Connected Party Presentation and Restriction Settings" section in the Cisco Unified Communications Manager System Guide.


Additional Information

See the "Related Topics" section.

Related Topics

SIP Route Pattern Configuration

SIP Route Pattern Configuration Settings

Understanding Session Initiation Protocol