Cisco Unified Communications Manager Features and Services Guide, Release 7.1(2)
Cisco Unified Mobility (Revised 10/24/2011)
Downloads: This chapterpdf (PDF - 688.0KB) The complete bookPDF (PDF - 21.17MB) | Feedback

Cisco Unified Mobility

Table Of Contents

Cisco Unified Mobility

Configuration Checklist for Cisco Unified Mobility

Introducing Cisco Unified Mobility

Definitions

List of Cisco Unified Mobility Features

Other Benefits of Cisco Unified Mobility Features

Mobile Connect

Desktop Call Pickup

Send Call to Mobile Phone

Mobile Voice Access

Midcall Enterprise Feature Access Support Using DTMF

Two-Stage Dialing

Time-of-Day Access

Time-of-Day Access Configuration

Important Notes for Time-of-Day Access

Directed Call Park via DTMF

SIP URI Dialing

Use Case Scenarios for Cisco Unified Mobility Features

Use Case Scenarios for Mobile Connect

Use Case Scenarios for Mobile Voice Access

Use Case Scenarios for Time-of-Day Access

Use Case Scenarios for Directed Call Park via DTMF

Interactions and Restrictions

Interactions

Licensing

Number of Supported Calls

Auto Call Pickup

Local Route Groups

Restrictions

System Requirements

Migrating from Cisco Unified MobilityManager

Configuring Cisco Unified Mobility

Access List Configuration

Finding Access Lists

Configuring Access Lists

Deleting Access Lists

Access List Configuration Settings

Access List Member Detail Configuration Settings

Remote Destination Profile Configuration

Finding Remote Destination Profiles

Configuring a Remote Destination Profile

Associating a Directory Number with a Remote Destination Profile

Deleting Remote Destination Profiles

Remote Destination Profile Configuration Settings

Remote Destination Configuration

Finding Remote Destinations

Configuring Remote Destinations

Deleting Remote Destinations

Remote Destination Configuration Settings

Mobile Voice Access Directory Number Configuration

Mobile Voice Access Configuration Settings

H.323 Gateway Configuration for Enterprise Feature Access

Configuring an H.323 Gateway for System Remote Access

Configuring an H.323 Gateway for System Remote Access by Using Hairpinning

Enterprise Feature Access Two-Stage Dialing

Mobility Setting Configuration

Mobility Configuration Settings

Mobility Softkey Configuration

Related Topics


Cisco Unified Mobility


Cisco Unified Mobility gives users the ability to redirect incoming IP calls from the Cisco Unified Communications Manager to up to ten different designated client devices such as mobile phones.

For example, Cisco Unified Mobility associates a user mobile phone number with the user business IP phone number. Cisco Unified Mobility then directs incoming calls to ring on a user mobile phone as well as the business phone, thus providing a single number for callers to reach the user. Calls that go unanswered on all the designated devices get redirected to the enterprise voice mailbox of the user (not to the mobile voice mailbox).

Administrators can configure Cisco Unified Mobility, formerly known as Cisco Unified MobilityManager, by using the Cisco Unified Communications Manager Administration windows to configure the setup for end users. End users can use Cisco Unified CM User Options windows to configure their own personal settings.

Cisco Unified Mobility comprises a number of features that this chapter discusses. The chapter provides an overview of the configuration procedures that administrators follow.

Refer to the user guide for a particular Cisco Unified IP Phone phone model for procedures that end users follow to configure the Cisco Unified Mobility settings for their phones by using the Cisco Unified CM User Options windows.


Note For explanations and configuration of features that are related to Cisco Unified Mobility and that require additional configuration of Cisco Unified Mobility Advantage and Cisco Unified Mobile Communicator, see the "Cisco Unified Mobility Advantage and Cisco Unified Mobile Communicator Integration" chapter. The chapter also points to other documentation that explains configuration of Cisco Unified Mobility Advantage and Cisco Unified Mobile Communicator.


This chapter includes information on the following topics:

Configuration Checklist for Cisco Unified Mobility

Introducing Cisco Unified Mobility

Definitions

List of Cisco Unified Mobility Features

Other Benefits of Cisco Unified Mobility Features

Mobile Connect

Mobile Voice Access

Time-of-Day Access

Directed Call Park via DTMF

SIP URI Dialing

Use Case Scenarios for Cisco Unified Mobility Features

Interactions and Restrictions

System Requirements

Migrating from Cisco Unified MobilityManager

Configuring Cisco Unified Mobility

Access List Configuration

Remote Destination Profile Configuration

Remote Destination Configuration

Mobile Voice Access Directory Number Configuration

H.323 Gateway Configuration for Enterprise Feature Access

Mobility Setting Configuration

Mobility Softkey Configuration

Related Topics

Configuration Checklist for Cisco Unified Mobility

Cisco Unified Mobility gives users the ability to redirect incoming IP calls from the Cisco Unified Communications Manager to up to ten different designated client devices such as mobile phones. For more information on Cisco Unified Mobility features, see the "List of Cisco Unified Mobility Features" section.

Table 13-1 summarizes the procedures for configuring Cisco Unified Mobility. For detailed instructions, see the chapters and sections that the table references. In addition, see the "Related Topics" section.

Table 13-1 Cisco Unified Mobility Configuration Checklist 

Configuration Steps
Related Procedures and Topics

Step 1 

Activate the Cisco Unified Mobile Voice Access Service in Cisco Unified Serviceability. You must activate this service on the first node in the cluster.

For information on activating services, refer to the Cisco Unified Serviceability Administration Guide.

Step 2 

Configure user accounts.

Note Make sure that you check the Enable Mobility check box and the Enable Mobile Voice Access check box in the End User Configuration window.

Note Checking the Enable Mobility check box triggers licensing to consume device license units (DLUs) for Mobile Connect.

End User Configuration, Cisco Unified Communications Manager Administration Guide

For information on how licensing works with Mobile Connect, refer to the "Licenses for Cisco Unified Mobility" section in the Cisco Unified Communications Manager System Guide.

Step 3 

Create access lists for Mobile Connect by assigning each list to the Mobile Connect user and specifying whether the list is an allowed or blocked list.

Access List Configuration.

Step 4 

Create remote destination profiles and assign each user to a profile.

Remote Destination Profile Configuration.

Step 5 

Associate desktop directory numbers (DNs) for the user.

Associating a Directory Number with a Remote Destination Profile.

Step 6 

Add remote destinations by selecting the previously-defined profile as part of the configuration.

Remote Destination Configuration.

Step 7 

In the Service Parameters Configuration window:

Choose True for Enable Mobile Voice Access and enter the Mobile Voice Access Number, which is the DID number that end users use to reach Mobile Voice Access.

Note To make Mobile Voice Access calls, you must configure these service parameters and check the Enable Mobile Voice Access check box in the End User Configuration window.

Choose True for Enable Enterprise Feature Access to enable access to hold, resume, transfer, and conference features from remote destinations.

Service Parameters Configuration, Cisco Unified Communications Manager Administration Guide

Step 8 

Configure the directory number for Mobile Voice Access.

Mobile Voice Access Directory Number Configuration.

Step 9 

As an alternative, configure Enterprise Feature Access Two-Stage Dialing (also known as Enterprise Feature Access) by configuring a service parameter and the enterprise feature access DID directory number.

Note Enterprise Feature Access provides the same functionality as Mobile Voice Access but does not support the IVR component. Also, Enterprise Feature Access does not require configuration of the H.323 gateway nor VXML.

Enterprise Feature Access Two-Stage Dialing

Step 10 

Configure mobility settings for dual-mode phone handoff.

Mobility Setting Configuration.

Step 11 

Configure a Mobility softkey for the phone user that uses Mobile Connect.

Mobility Softkey Configuration

Step 12 

Configure time-of-day access for users. Use the fields in the When Mobile Connect is Enabled pane of the Remote Destination Configuration window to do so.

Remote Destination Configuration.

Introducing Cisco Unified Mobility

Administrators configure the basic setup of Cisco Unified Mobility for end users by using the Cisco Unified Communications Manager Administration windows.

This section discusses the following topics:

Definitions

List of Cisco Unified Mobility Features

Other Benefits of Cisco Unified Mobility Features

Mobile Connect

Mobile Voice Access

Time-of-Day Access

Directed Call Park via DTMF

SIP URI Dialing

Use Case Scenarios for Cisco Unified Mobility Features

Additional Information

See the "Related Topics" section.

Definitions

Table 13-2 provides definitions of terms that are related to Cisco Unified Mobility.

Table 13-2 Definitions 

Term
Definition

Access List

List that determines the phone numbers that the system can pass or block from being passed to remote destinations.

Mobile Connect

Feature that allows users to answer incoming calls on the desktop phone or at a remote destination and to pick up in-progress calls on the desktop phone or at a remote destination without losing the connection.

Mobile Voice Access

Interactive voice response (IVR) system that is used to initiate two-stage dialed calls through the enterprise and to activate or deactivate Mobile Connect capabilities.

Enterprise Feature Access

Feature that provides the ability for users to access midcall features (Hold, Resume, Transfer, Conference, Directed Call Park), two-stage dialing, and Mobile Connect activate and deactivate from a remote destination.

With this method, the user does not get prompted for keypad entries and must be aware of the required key sequence.

Remote Destination

Phones that are available for Mobile Connect answer and pickup and that can leverage Mobile Voice Access and Enterprise Feature Access for two-stage dialing. Remote destinations may include any of the following devices:

Single-mode mobile (cellular) phones

Smartphones

Dual-mode phones

Enterprise IP phones that are not in the same cluster as the desktop phone

Home phone numbers in the PSTN.

Remote Destination Profile

Set of parameters that apply to all remote destinations for the user.

Time-of-Day Access

Feature that associates ring schedules to access lists and determines whether a call will be extended to a remote destination during the time of day when such a call is received.


Additional Information

See the "Related Topics" section.

List of Cisco Unified Mobility Features

This section provides a list of Cisco Unified Mobility features that administrators configure by using Cisco Unified Communications Manager Administration.

The following features, which were originally part of Cisco Unified MobilityManager, now reside in Cisco Unified Communications Manager:

Mobile Connect—This feature enables users to manage business calls by using a single phone number to pick up in-progress calls on the desktop phone and the mobile phone. Refer to the "Mobile Connect" section for a detailed discussion.

Desktop Call Pickup—Users can switch between desktop phone and mobile phone during an active call without losing the connection. Based on the needs of the moment, they can take advantage of the reliability of the wired office phone or the mobility of the mobile phone. Refer to the "Desktop Call Pickup" section for a detailed discussion.

Send Call to Mobile Phone(s)—Users access this feature on the IP phone via the Mobility softkey. The feature triggers a remote destination pickup, which allows the user to move an active mobility call from the user desk phone to a configured remote destination phone. Refer to the "Send Call to Mobile Phone" section for a detailed discussion.

Mobile Voice Access—This feature extends Mobile Connect capabilities by providing an interactive voice response (IVR) system to initiate two-stage dialed calls through the enterprise and activate or deactivate Mobile Connect capabilities. Refer to the "Mobile Voice Access" section for a detailed discussion.

Access List—Users can restrict the set of callers that cause a designated remote destination to ring on an incoming call (allowed access list) or for which the remote destinations do not ring on an incoming call (blocked access list). Each remote destination represents a mobile or other phone that can be configured to accept transfers from the desktop phone for the user.

Cisco Unified Communications Manager supports the following Cisco Unified Mobility features:

Midcall Enterprise Feature Access Support Using DTMF—You can configure DTMF feature codes as service parameters: exclusive Hold (default equals *81), enterprise exclusive hold (default equals *82), resume (default equals *83), transfer (default equal *84), and conference (default equals *85). Refer to the "Midcall Enterprise Feature Access Support Using DTMF" section for a detailed discussion.


Note *81 specifies enterprise hold. When invoked, enterprise hold allows the user to resume the call on the desk phone. *82 specifies enterprise exclusive hold. When invoked, enterprise exclusive hold does not provide the ability to resume on the desk phone.


Two-stage Dialing—Be aware that enterprise features are available with two-stage dialing for smartphones. Two-stage dialing allows smartphones to make outgoing calls through Cisco Unified Communications Manager if the smartphone is in business mode. The smartphone dials the Enterprise Feature Access number for Cisco Unified Communications Manager and then dials the destination number. Refer to the "Two-Stage Dialing" section for a detailed discussion.

Dual-mode Phone Support—Cisco Unified Mobility supports dual-mode phones.

Manual Handoff of Calls on a Dual-mode Phone—Dual-mode devices offer an option to manually hand off calls from the PSTN to WLAN and vice versa.

Time-of-Day Access—When the Mobile Connect feature is enabled, calls get extended to remote destinations if the associated DN is called based on time-of-day-access-based configuration. Refer to "Time-of-Day Access" section for a detailed discussion.

Directed Call Park via DTMF—This feature allows a mobile phone user to park a call by transferring the parkee party to a park code, so the call can be retrieved later. The feature combines the standard Cisco Unified Communications Manager Directed Call Park feature with the DTMF feature. Support of the Directed Call Park via DTMF feature leverages the Midcall Enterprise Transfer feature. Refer to "Directed Call Park via DTMF" section for a detailed discussion.

SIP URI Dialing—This feature supports SIP URI as an additional type of Remote Destination for Cisco Unified Mobility. Refer to "SIP URI Dialing" section for a detailed discussion.

Additional Information

See the "Related Topics" section.

Other Benefits of Cisco Unified Mobility Features

Cisco Unified Mobility allows flexible management of enterprise and mobile phone communications and provides these additional features and benefits:

Simultaneous desktop ringing—Incoming calls ring simultaneously on the IP phone extension and the designated mobile handset.When the user answers one line, the unanswered line automatically stops ringing. Users can choose the preferred device each time that a call comes in.

Single enterprise voice mailbox—The enterprise voice mailbox can serve as single, consolidated voice mailbox for all business, including calls to the desktop or configured remote devices. Incoming callers have a predictable means of contacting employees, and users can check multiple voice-messaging systems in less time.

System remote access—A mobile phone for the user can initiate calls as if it were a local IP PBX extension. User-initiated calls can take advantage of local voice gateways and WAN trunking, and the enterprise can track employee call initiation.

Caller ID—The system preserves and displays Caller ID on all calls. Users can take advantage of Mobile Connect with no loss of expected IP phone features.

Remote on/off control—User can turn Mobile Connect feature. See "Methods for Enabling and Disabling Mobile Connect" section for details.

Call tracing—The system logs detailed Mobile Connect calls and provides information to help the enterprise optimize trunk usage and debug connection problems.

Security and privacy for Mobile Connect calls—During an active Mobile Connect call, the associated desktop IP phone remains secured. The system eliminates access to the call from the desktop as soon as the mobile connection becomes active, which precludes the possibility of an unauthorized person listening in on the call that is bridged to the mobile phone.

Smartphone support—Users can use the enterprise hold, resume, transfer, and conference softkeys on the smartphone in an active call. Users can enable or disable Mobile Connect from a smartphone. Users can also perform Enterprise Feature Access two-stage dialing from a smartphone.

Additional Information

See the "Related Topics" section.

Mobile Connect

Mobile Connect allows users to answer incoming calls on the desktop phone or mobile phone, and to pick up in-progress calls on the desktop phone or mobile phone without losing the connection.


Note You can use any mobile phone, including Code Division Multiple Access (CDMA) and Global System for Mobile Communications (GSM) phones, for Mobile Connect and Mobile Voice Access. In some cases, however, you may need to modify timer settings in Cisco Unified Communications Manager to ensure compatibility. See the "Configuring Remote Destinations" section.


Methods for Enabling and Disabling Mobile Connect

The following methods are available for enabling and disabling the Mobile Connect feature. This list provides the methods available to the administrator and to end users.

Mobile phone by using Mobile Voice Access (2 to enable, 3 to disable)

Mobile phone by using Enterprise Feature Access (2 to enable, 3 to disable)

Desktop phone by using the Mobility softkey

Cisco Unified CM User Options windows

Cisco Unified Communications Manager Administration windows (specifically, the Enable Mobile Connect check box in the Remote Destination Configuration window)

Cisco Unified Mobile Communicator client (See the "Cisco Unified Mobility Advantage and Cisco Unified Mobile Communicator Integration" for more information.)

Mobile Connect Status

If at least one configured remote destination for a user is enabled for Mobile Connect, the user desktop phone displays Mobile Connect as Enabled.

Refer to the "Use Case Scenarios for Mobile Connect" section for the use case scenarios that Cisco Unified Communications Manager supports with this feature.

Additional Information

See the "Related Topics" section.

Desktop Call Pickup

User can perform desktop call pickup on in-progress mobility calls either by hanging up the call on the mobile phone or by putting the mobility call on hold with the midcall hold feature. When hanging up or ending the call at the mobile phone, the user can then resume the call on the desktop phone within 10 seconds (default). When the remote destination hangs up, Cisco Unified Communications Manager puts the associated desktop phone in Hold state, which allows the user to resume the call by pressing the Resume softkey. The Maximum Wait Time for Desk Pickup setting on the End User Configuration window determines the amount of time the call remains on hold after the hang-up at the remote destination. The default specifies 10000 milliseconds (10 seconds).

Alternatively, the user can also perform desktop call pickup by placing the call on the mobile phone on enterprise hold with the midcall hold feature (*81) and then resuming the call on the desktop phone. When Cisco Unified Communications Manager receives the *81, Cisco Unified Communications Manager places the associated desktop phone in a Hold state so the user can resume the call. Note that with this method, the Maximum Wait Time for Desk Pickup timer does not apply to the hold state and the call gets held indefinitely until the user resumes the call.

Additional Information

See the "Related Topics" section.

Send Call to Mobile Phone

User can perform remote destination pickup on in-progress mobility calls by using the Send Call to Mobile Phone feature. To do so, the user presses the Mobility softkey on the desktop phone and selects Send Call to Mobile Phone, which generates calls to all of the remote destinations that are configured for the user. The user can then answer this call at the desired remote destination and continue the call.

Additional Information

See the "Related Topics" section.

Mobile Voice Access

Mobile Voice Access extends Mobile Connect capabilities by allowing users to originate a call from a remote destination such as a mobile phone as if dialing from the desktop phone. A remote destination represents a phone that is designated as available for Mobile Connect answer and pickup. The user dials Mobile Voice Access from the remote destination. The system prompts the user for the PIN that is assigned to the user in Cisco Unified Communications Manager. After being authenticated, the user can make a call by using the same dialing methods that would be available if the user originated the call from the enterprise desktop phone.

When Mobile Voice Access is called, the system prompts the user for the originating phone number in addition to the PIN if any of the following statements is true:

The number from which the user is calling does not represent one of the remote destinations for the user.

The user or the carrier for the user blocks the number (shown as "Unknown Number").

The number does not get accurately matched in the Cisco Unified Communications Manager database; for example, if the number is 510-666-9999, but it is listed as 666-9999 in the database, or the number is 408-999-6666, but it is entered as 1-408-999-6666 in the database.

Mobile Voice Access gets configured in hairpin mode. (When Mobile Voice Access that is configured in hairpin mode is used, users who are calling the system do not get identified automatically by their caller ID. Instead, users must manually enter their remote destination number prior to entering their PIN number.)

If the user incorrectly enters any requested information (such as mobile phone number or PIN) three times in a row, the Mobile Voice Access call can disconnect, and the system will lock out the user for a period of time. (The credential information for the user controls the allowed number of login attempts.)


Note Mobile Voice Access uses the first locale that displays in the Selected Locales pane in the Mobile Voice Access window in Cisco Unified Communications Manager Administration (Media Resources > Mobile Voice Access) when the IVR is used. For example, if English United States displays first in the Selected Locales pane, the Cisco Unified Mobility user receives English when the IVR is used during a call.


Refer to the "Use Case Scenarios for Mobile Voice Access" sectionfor the use case scenarios that Cisco Unified Communications Manager supports with this feature.

Additional Information

See the "Related Topics" section.

Midcall Enterprise Feature Access Support Using DTMF

Users can leverage enterprise media resources and capabilities by invoking midcall features. DTMF digits that are relayed from the remote destination inband in the audio path and then relayed out-of-band from the enterprise gateway to Cisco Unified Communications Manager invoke midcall features. When Cisco Unified Communications Manager receives the DTMF digits, appropriate midcall features get facilitated based on the DTMF digit sequence. Such features include adding or remove call legs for transferred or conferenced calls, as well as invoking media resources like music on hold for held calls and conference bridges as required.

The feature Access codes that are configured within Cisco Unified Communications Manager under Service Parameters determine the midcall feature DTMF code sequences.

Additional Information

See the "Related Topics" section.

Two-Stage Dialing

The user can originate calls from the remote destination phone through the enterprise by leveraging the enterprise telephony infrastructure. Two-stage dialing provides the following benefits:

The ability to make calls through the enterprise, which leads to centralized billing and call detail records. This ability provides the potential for cost savings by ensuring that international calls get billed to the enterprise rather than to the mobile or cellular plan. However, this capability does not eliminate normal per-minute local/long-distance charges at the mobile phone.

The ability to mask the mobile phone number from the far-end or dialed phone. Instead of sending the mobile number to the called party, the user enterprise number gets sent to the called party during a two-stage dialed call. This method effectively masks the user mobile number and ensures that returned calls get anchored in the enterprise.

Additional Information

See the "Related Topics" section.

Time-of-Day Access

An access list determines whether a call should be extended to a remote destination that is enabled for the Mobile Connect feature. With the addition of time-based control, the Time-of-Day Access feature adds time as another determination factor. The feature allows administrators and users to determine whether a call should reach a remote destination based on the time of day when the call is received.

For calls to remote destinations, the Time-of-Day Access feature adds a ring schedule and associates the ring schedule with an access list to determine the time-of-day access settings for a remote destination.

The provisioning process includes provisioning the following entities:

Access lists

Remote destinations (configuring a ring schedule and associating the ring schedule with an access list for a remote destination)

As an extension to the existing access list feature, ensure the Time-of-Day Access feature is accessible to end users of Cisco Unified Communications Manager. Therefore, you can provision the feature through use of both Cisco Unified Communications Manager Administration (by administrators) and Cisco Unified CM User Options (by end users).

Time-of-Day Access Example

The following example illustrates a specific time-of-day access application:

Block 1800! during business hours for user brownse.

Further Topics

This section includes the following topics:

Time-of-Day Access Configuration

Important Notes for Time-of-Day Access

The "Use Case Scenarios for Time-of-Day Access" section provides use case scenarios for the time-of-day access feature with Cisco Unified Mobility, including migration considerations when migrating from a release of Cisco Unified Communications Manager prior to Release 7.0(x) or later.

Additional Information

See the "Related Topics" section.

Time-of-Day Access Configuration

Table 13-3 summarizes the procedures for configuring the Time-of-Day Access feature for Cisco Unified Mobility. For detailed instructions, see the chapters and sections that the table references.

Table 13-3 Time-of-Day Access Configuration Checklist 

Configuration Steps
Related Procedures and Topics

Step 1 

In Cisco Unified Communications Manager Administration, configure an end user for whom you will enable the Time-of-Day Access feature.

Use the User Management > End User menu option.

Note Make sure that you check the Enable Mobility check box in the End User Configuration window.

Note Checking the Enable Mobility check box triggers licensing to consume device license units (DLUs) for Mobile Connect.

End User Configuration, Cisco Unified Communications Manager Administration Guide

For information on how licensing works with Mobile Connect, refer to the "Licenses for Cisco Unified Mobility" section in the Cisco Unified Communications Manager System Guide.

Step 2 

For a particular user, configure access lists to use for Time-of-Day Access by assigning each list to the user. Create separate access lists for callers that are allowed and callers that are blocked.

Note An access list must have an owner. No system access list exists.

Use the Call Routing > Class of Control > Access List menu option.

Access List Configuration

Step 3 

Create remote destination profiles and assign each user to a profile.

Remote Destination Profile Configuration.

Step 4 

Configure a remote destination for a user. Remote destinations represent the mobile (or other) phones that can accept Mobile Connect calls and calls that are moved from the desktop phone. Remote destinations can initiate calls by using Mobile Voice Access.

Use the Device > Remote Destination menu option.

Note The same configuration also applies to dual-mode phones and to Cisco Unified Mobile Communicator Mobility Identity to set up time-of-day access.

For successful time-of-day access configuration, you must configure the following areas in the Remote Destination Configuration window:

Use the Ring Schedule pane to configure a ring schedule for the remote destination.

Use the When receiving a call during the above ring schedule pane to specify the access list for which the Ring Schedule applies.

Checking the Enable Mobile Connect check box for the remote destination enables Cisco Unified Mobility to apply the settings in the When Mobile Connect is Enabled pane to calls that are made to this remote destination. If the Enable Mobile Connect check box is not checked, the settings do not apply to incoming calls to this remote destination, but the settings remain intact for future use.

Remote Destination Configuration

Additional Information

See the "Related Topics" section.

Important Notes for Time-of-Day Access

The following important notes apply to time-of-day access configuration:

A ring schedule associates with the time zone of a remote destination, not with the time zone of the Cisco Unified Communications Manager server. Use the Time Zone field in the Remote Destination Configuration window to specify the time zone of the remote destination.

If a remote destination has no time-of-day access configuration, all calls get extended to the remote destination. By default, the All the time ring schedule radio button and the Always ring this destination radio button are checked, so that all calls get extended to the remote destination.

Cisco recommends that you always configure an access list with members; avoid creating an empty access list that contains no members. If an empty access list is chosen in the Ring this destination only if the caller is in drop-down list box, all calls get blocked (instead of allowed). If an empty access list is chosen in the Do not ring this destination if the caller is in drop-down list box, all calls are allowed during the specified ring schedule. Either use of an empty access list could cause unnecessary confusion for end users.

Refer to the "Use Case Scenarios for Time-of-Day Access" section for the use case scenarios that Cisco Unified Communications Manager supports with this feature.

Refer to the user guide for the applicable Cisco Unified IP Phone model for details of the settings that end users can configure to customize their time-of-day access settings by using the Cisco Unified CM User Options windows.

Additional Information

See the "Related Topics" section.

Directed Call Park via DTMF

A user can park an existing call by using DTMF digits. Using Directed Call Park from the mobile phone, a user parks a call and inputs a unique mobility user park code. The user can subsequently retrieve the call with the code or have someone else retrieve the call with the code. This feature proves useful for certain vertical markets that require different departments or users to pick up calls.

When a user is in the enterprise and picks up a call on their mobile phone, they may want to pick the call up on a Cisco Unified IP Phone in a conference room or desk where the DN is not visible. The user can park the call and pick up the parked call with only their code.

When the mobile phone user is on an active call, the user can park the call by transferring the parkee party to the park code that the system administrator configures and assigns to the user. The dialing sequence resembles the DTMF transfer sequence, except that a preconfigured parking code replaces the transfer number.

Example of Directed Call Park via DTMF—Parking the Call

In the following example, *82 specifies enterprise exclusive hold, *84 specifies transfer, the pin specifies 12345, and the call park code specifies 3215. The following actions take place from the mobile phone:

1. Dial *82 (to put the call on enterprise exclusive hold).

2. If necessary, put the mobile phone call on Hold, depending on the mobile phone model.

3. Make a new call to the Enterprise Feature Access DID.


Note This same DID gets used for the Enterprise Feature Access two-stage dialing feature. Configure this DID with the Call Routing > Mobility Configuration menu option.


4. After the call connects, dial this digit sequence: 12345#*84#3215#*84#.

Cisco Unified Communications Manager puts the parkee party on hold.


Note The caller ID of the mobile phone must get passed to the enterprise and must match a configured remote destination when the user dials the Enterprise Feature Access DID to invoke this feature. If no caller ID exists or no caller ID match occurs, the user cannot invoke this feature.


After Cisco Unified Communications Manager receives the dialed park code digit, the digit analysis engine verifies whether the dialed park code digits are valid. If so, the Directed Call Park feature intercepts the park code and verifies whether the park code is available. If the dialed park code is valid and available, the parker party receives the ringback tone, and the secondary call terminates to a Cisco Unified Communications Manager generic device that associates with the selected park code. The generic device automatically answers and place the parker party on hold with music on hold (MOH) or tone on hold. The last *84 completes the transfer of the parkee to the Cisco Unified Communications Manager generic device that associates with the selected park code. After the transfer completes, the parkee party receives the MOH or tone on hold, and the parkee gets parked on this selected park code and waits for retrieval.

If another user is already using the user-specified park code, Directed Call Park feature logic in Cisco Unified Communications Manager rejects that selected park code. The user gets to select another park code.

If the user-specified park code is not valid, Cisco Unified Communications Manager plays reorder tone to the parker party.

For the Directed Call Park feature, be aware that the park code and code range are configurable across a cluster. Every Cisco Unified Communications Manager server in the cluster shares the park code and code range.

Example of Directed Call Park via DTMF—Retrieving the Parked Call

When a user attempts to retrieve the parked call, the user can go off hook on another mobile phone, and the user must use two-stage dialing to dial a digit string that contains the Directed Call Park retrieval prefix digits (for example, 22) plus the park code/code range (for example, 3215). The following sequence of events takes place:

1. Dial Enterprise Feature DID on mobile phone.

2. Upon connection, press PIN#1#223215# to retrieve the parked call.

Just like the existing Call Park feature, if the call does not get retrieved on time, the parked call reverts back to the phone number that is associated with the parker party by default.

If a shared line is configured for the phone line of the parker, all phones that are associated with the shared line will ring. In addition, the dPark feature allows the administrator to configure a call park reversion number in the Directed Call Park Configuration window, so if the call park reversion number is configured, the non-retrieved call reverts to this number, instead of to the parker party number.

Refer to "Use Case Scenarios for Directed Call Park via DTMF" section for the use case scenarios that Cisco Unified Communications Manager supports with this feature.

Additional Information

See the "Related Topics" section.

SIP URI Dialing

This feature supports Session Initiation Protocol (SIP) Universal Resource Identifier (URI) as an additional type of remote destination for Cisco Unified Mobility. When the DN is called, Cisco Unified Communications Manager extends the call to a SIP trunk that digit analysis selects with this SIP URI in the To: header.

This feature only allows routing that is based only on the domain name, not based on the full SIP URI.

When a remote destination of this type is configured, other Cisco Unified Mobility features, such as two-stage dialing, transformation to DN number when calling into Cisco Unified Communications Manager, Interactive Voice Response (IVR) support, caller ID match, or DTMF transfer and conferencing, do not get supported.

SIP URI Administration Details

The SIP URI dialing feature entails a relaxation of the business rules to allow the entry of a URI in the Destination Number field of the Remote Destination Configuration window. (From the Cisco Unified Communications Manager Administration menu bar, choose the Device > Remote Destination menu option.)

An additional requirement for this feature specifies that a SIP route pattern that matches the configured URI domain must be configured for the feature to work. To configure a SIP route pattern, from the Cisco Unified Communications Manager Administration menu bar, choose the Call Routing > SIP Route Pattern menu option.

SIP URI Example

For a remote destination, the SIP URI user@corporation.com gets configured. A SIP route pattern that specifies corporation.com must also get configured for the SIP URI remote destination to resolve correctly.

Additional Information

See the "Related Topics" section.

Use Case Scenarios for Cisco Unified Mobility Features

The following sections describe the following use case scenarios that Cisco Unified Communications Manager supports for Cisco Unified Mobility features:

Use Case Scenarios for Mobile Connect

Use Case Scenarios for Mobile Voice Access

Use Case Scenarios for Time-of-Day Access

Use Case Scenarios for Directed Call Park via DTMF

Additional Information

See the "Related Topics" section.

Use Case Scenarios for Mobile Connect

Mobile Connect supports these use case scenarios:

Receiving an outside call on desktop phone or mobile phone—An outside caller dials the user desktop extension. The desktop phone and mobile phone ring simultaneously. When the user answers one phone, the other phone stops ringing. The user can switch from the desktop phone to a mobile phone during a call without losing the connection. Switching gets supported for incoming and outgoing calls.

Moving back from a mobile phone to a desktop phone—If a call was initiated to or from the desktop phone and then shifted to the mobile phone, the call can get shifted back to the desktop phone.

Using midcall enterprise features—During a Mobile Connect call, users can perform midcall functions, including hold/resume, exclusive hold, transfer, directed call park, and conference.

Additional Information

See the "Related Topics" section.

Use Case Scenarios for Mobile Voice Access

Mobile Voice Access supports these use case scenarios:

Initiating a mobility call from a remote phone, such as a mobile phone—Users can use Mobile Voice Access to initiate calls from a mobile phone as if dialing from the desktop phone.

Moving from a mobile phone to a desktop phone during a mobile-phone-initiated call—If the user initiated a call from a mobile phone by using Mobile Voice Access, the user can shift to the desktop phone during the call without losing the connection and can shift back again as needed.

Additional Information

See the "Related Topics" section.

Use Case Scenarios for Time-of-Day Access

The use case scenarios that follow detail the function of the time-of-day access feature with activated access lists that were configured prior to the addition of the time-of-day access feature, as well as with new provisioning that takes place for the feature starting with Release 7.0(1) of Cisco Unified Communications Manager.

Supported Use Cases for Migrating Activated Access Lists from an Earlier Cisco Unified Communications Manager Release

The following use cases detail the function of the Time-of-Day Access feature with Cisco Unified Mobility when migration of an activated access list from a previous release of Cisco Unified Communications Manager to Release 7.0(x) or later takes place.

Use Case #1—No allowed or blocked access list got configured prior to Release 7.0(x) of Cisco Unified Communications Manager.

Result after migration: The system allows all calls at all hours. The Remote Destination Configuration window displays the When Mobile Connect is Enabled pane. In the Ring Schedule pane, the All the time radio button is checked. In the When Receiving a call during the above ring schedule pane, the Always ring this destination radio button is checked.

Use Case #2—Only an allowed access list got configured prior to Release 7.0(x) of Cisco Unified Communications Manager.

Result after migration: Only the callers that belong to the allowed access list can reach the associated remote destination. The Remote Destination Configuration window displays the When Mobile Connect is Enabled pane. In the Ring Schedule pane, the All the time radio button is checked. In the When Receiving a call during the above ring schedule pane, the Ring this destination only if caller is in radio button is checked, and the access list displays in the corresponding drop-down list box.

Use Case #3—Only a blocked access list got configured prior to Release 7.0(x) of Cisco Unified Communications Manager.

Result after migration: The callers that belong to the blocked access list cannot reach the associated remote destination, but all other callers can call the remote destination at all hours. The Remote Destination Configuration window displays the When Mobile Connect is Enabled pane. In the Ring Schedule pane, the All the time radio button is checked. In the When Receiving a call during the above ring schedule pane, the Do not ring this destination if caller is in radio button is checked, and the access list displays in the corresponding drop-down list box.

Use Cases for Time-of-Day Access with the Current Cisco Unified Communications Manager Release

The following use cases detail the function of the Time-of-Day Access feature with Cisco Unified Mobility with the current release of Cisco Unified Communications Manager:

Use Case #4—Only allow calls during business hours.

Configuration: Configure a ring schedule that specifies business hours from Monday to Friday and choose the Always ring this destination radio button.

Result: The system allows all callers during business hours, but no calls get extended to this remote destination outside business hours.

Use Case #5—Only allow calls from certain numbers (for example, from coworkers) during business hours.

Configuration: Configure a ring schedule that specifies business hours from Monday to Friday, choose the Ring this destination only if the caller is in radio button, and specify an access list.

Result: Only callers that belong to the access list can call the remote destination during business hours; all other callers get blocked during business hours. Outside business hours, no calls ring this remote destination.

Use Case #6—Block certain numbers (for example, 1800 numbers) during business hours.

Configuration: Configure a ring schedule that specifies business hours from Monday to Friday, choose the Don't ring this destination if the caller is in radio button, and specify an access list.

Result: Only callers that belong to the access list get blocked from calling the remote destination during business hours; all other callers can call the remote destination during business hours. Outside business hours, no calls ring this remote destination.

Additional Information

See the "Related Topics" section.

Use Case Scenarios for Directed Call Park via DTMF

The Directed Call Park via DTMF feature of Cisco Unified Mobility supports the following use cases:

Mobile phone user parks call on selected park code.

Mobile phone user parks call on selected park code that is unavailable.

Mobile phone user parks call on selected park code that is invalid.

Mobile phone user fails to enter park code after entering the DTMF transfer code.

Parkee party disconnects while the parker party attempts to park the call.

Parkee party disconnects while it is parked on a selected park code and is waiting for retrieval.

User dials Directed Call Park retrieval digits plus a park code that has not been occupied.

Administrator configures a translation pattern, so the length of the string of digits to park a call and to retrieve a call are the same.

User retries a parked call.

A parked call reverts.

While a park code is occupied, one of the following entities gets modified or deleted: the park code or code range, the Directed Call Park park-prefix digits, or the Directed Call Park retrieval-prefix digits.

Directed call park gets specified when the network is partitioned.

Additional Information

See the "Related Topics" section.

Interactions and Restrictions

Most standard Cisco Unified Communications Manager features are fully compatible with Cisco Unified Mobility features, except as indicated in the following sections:

Interactions

Restrictions

Additional Information

See the "Related Topics" section.

Interactions

The following sections detail the interactions between Cisco Unified Mobility and other Cisco Unified Communications Manager components:

Licensing

Number of Supported Calls

Auto Call Pickup

Local Route Groups

Additional Information

See the "Related Topics" section.

Licensing

Mobile Connect uses licensing. Checking the Enable Mobility check box in the End User Configuration window triggers licensing to consume device license units (DLUs) for Mobile Connect; the number of licenses that get consumed depends on whether you assign an adjunct device to the end user specifically for Cisco Unified Mobility. For specific information on how licensing works with Cisco Unified Mobility, see the following sections:

"Licenses for Cisco Unified Mobility" section in the Cisco Unified Communications Manager System Guide.

"Cisco Unified Mobility for End Users" in the Cisco Unified Communications Manager System Guide.

Additional Information

See the "Related Topics" section.

Number of Supported Calls

Each remote destination supports a maximum of two active calls. For Cisco Unified Mobility, each remote destination supports a maximum of two active calls via Cisco Unified Communications Manager. Using the Enterprise Feature Access directory number (DID number) to transfer or conference with DTMF counts as one call. When a Cisco Unified Mobility user receives a call while the user has two active calls for the remote destination or while the user is using DTMF to transfer/conference a call from the remote destination, the received call does not reach the remote destination and instead goes to the enterprise voice mail; that is, if Call Forward No Answer (CFNA) is configured or if the call is not answered on a shared line.

Additional Information

See the "Related Topics" section.

Auto Call Pickup

Cisco Unified Mobility interacts with auto call pickup based on the service parameter selection. When the Auto Call Pickup Enabled service parameter is set to True, end users need only to press the PickUp softkey to pick up a call.

If the Auto Call Pickup Enabled service parameter is set to False, end users need to press the PickUp, GPickUp, or OPickUp softkey and then the Answer softkey.

Example

Phone A, phone B (Cisco Unified Mobility subscriber), and phone C belong to the Engineering group; phone D, phone E, and phone F belong to the Accounting group.

Phone D calls phone A in the Engineering Group. Phone A rings, and phone B and phone C in the group receive pickup notice.

If Auto Call Pickup is enabled, press the PickUp softkey from phone B to use Cisco Unified Mobility features later on.

If Auto Call Pickup is not enabled, press PickUp softkey from phone B, which causes the remote destinations that are associated with phone B to ring. Press the Answer softkey on phone B, which causes the remote destinations to stop ringing. The user can subsequently perform mobile-phone pickup and desktop call pickup.

Additional Information

See the "Related Topics" section.

Local Route Groups

For Single Number Reach calls to a remote destination, the device pool of the originating calling party determines the selection of the Standard Local Route Group.

Additional Information

See the "Related Topics" section.

Restrictions

Cisco Unified Mobility enforces the following restrictions in operating with other Cisco Unified Communications Manager components:

Forced Authorization Code and Client Matter Code

Multilevel Precedence and Preemption (MLPP)

Video Calls

Remote Destinations

Remote Destination Profiles

Conferencing

QSIG

QSIG Path Replacement

Dual-Mode Handoff and Caller ID

Dual-Mode Phones and CTI Applications

Dual-Mode Phones and Desktop Call Pickup

Enterprise Features in GSM That Is Using DTMF

Gateways and Ports

Enterprise Features From Cellular Networks

Call Anchoring

Call Forwarding

Multiple-Node Cluster Environment

Service Parameters

Dialing + Character From Mobile Phones

Maximum Wait Timer for Desktop Call Pickup Does Not Get Applied If Hold DTMF Is Pressed

Cisco Unified IP Phones 7940 and 7960 That Are Running SIP

Forced Authorization Code and Client Matter Code

The Forced Authorization Code and Client Matter Code (FAC/CMC) feature does not work with Mobile Voice Access.

The Forced Authorization Code (FAC) does not get invoked for Mobile Connect [Single Number Reach (SNR)] calls to a remote destination.

Multilevel Precedence and Preemption (MLPP)

Mobile Connect does not work with Multilevel Precedence and Preemption (MLPP). If a call is preempted with MLPP, Mobile Connect features get disabled for that call.

Video Calls

Mobile Connect services do not extend to video calls. A video call that is received at the desktop phone cannot get picked up on the mobile phone.

Remote Destinations

Ensure remote destinations are Time Division Multiplex (TDM) devices. You cannot configure IP phones within a Cisco Unified Communications Manager cluster as remote destinations.

Ensure remote destinations specify PSTN numbers or numbers across ICT trunks.

Remote destinations cannot resume calls that Cisco Unified IP Phones put on hold.

Remote Destination Profiles

When configuring a directory number that is associated with a remote destination profile, you must use only ASCII characters in the Display (Internal Caller ID) field on the Directory Number Configuration window.

Conferencing

Users cannot initiate a meet-me conference as conference controller by using Mobile Voice Access but can join a meet-me conference.

If an existing conference call is initiated from a shared-line IP phone or dual-mode phone or smartphone that is a remote destination, no new conference party can get added to the existing conference after the call is sent to a mobile phone or a dual-mode handoff action occurs. To permit the addition of new conference parties, use the Advanced Ad Hoc Conference Enabled service parameter.

QSIG

Mobility does not support QSIG.

QSIG Path Replacement

QSIG (Q Signaling) path replacement does not get supported.

Dual-Mode Handoff and Caller ID

Dual-mode handoff requires that caller ID be available in the cellular network.

Dual-Mode Phones and CTI Applications

While a dual-mode phone is in Wi-Fi enterprise mode, no CTI applications control it nor monitor it.

The In Use Remote indicator for dual-mode phones on a shared line call in the WLAN disappear if the dual-mode phone goes out of WLAN range.

Dual-Mode Phones and Desktop Call Pickup

The desktop call pickup feature does not apply to the following mobile phone models:

Nokia 902iL and Nokia 906iL dual-mode phones that are running SIP

Nokia S60 dual-mode phones that are running SCCP

For these phone models, if the mobile phone user hangs up a call, the calling party hears music on hold for ten seconds (as configured by the Maximum Wait Time for Desk Pickup field for the remote destination end user) and then the call drops. Because the desktop call pickup feature does not get supported for these phone models, the user desktop phone does not display the Resume softkey, so the user cannot pick up the call on the desktop phone.

Enterprise Features in GSM That Is Using DTMF

Availability of enterprise features in GSM that is using DTMF depends upon the features that are supported in the third-party smartphones.

Gateways and Ports

Only H.323 gateways get supported for Mobile Voice Access.

Mobile Connect features do not get supported for T1 CAS, FXO, FXS and BRI.

Enterprise Features From Cellular Networks

Enterprise features from cellular networks require out-of-band DTMF.


Note When using intercluster DNs as remote destinations for an IP phone via SIP trunk (either intercluster trunk [ICT] or gateway), check the Require DTMF Reception check box when configuring the IP phone, so DTMF digits can be received out of band, which is crucial for Enterprise Feature Access midcall features.


Call Anchoring

Call anchoring, which is performed based on caller ID, gets supported only from calls from registered single-mode or dual-mode phones

Call Forwarding

You do not need to configure settings for call forward unregistered, if the end user has configured remote destinations. Appropriate call forwarding will get handled as part of the Mobile Connect process.

Multiple-Node Cluster Environment

In a multiple-node cluster environment, if the Cisco Unified Communications Manager publisher server is unreachable, any changes that end users make to turn Mobile Connect off or on by way of Mobile Voice Access or two-stage dialing do not get saved.

Service Parameters

Enterprise feature access service parameters apply to standard phones and smartphones; however, smartphones generally use one-touch keys to send the appropriate codes. Administrators must configure any smartphones that will be used with Mobile Connect to use either the default codes for enterprise feature access or the codes that are specified in the smartphone documentation.


Note The enterprise feature access virtual device is always in the Default region. If you change the default to another region, the field still remains as Default.


Dialing + Character From Mobile Phones

Users can dial a + sign through DTMF on a mobile phone to specify the international escape character.

Cisco Unified Mobility does not support + dialing through DTMF for interactive voice response (IVR) to make an outgoing call from a mobile phone to an enterprise IP phone for which the directory number contains the + character.

Cisco Unified Mobility does not support + dialing through DTMF for two-stage dialing to make an outgoing call from a mobile phone to an enterprise IP phone for which the directory number contains the + character.

For more information about configuring the international escape character in Cisco Unified Communications Manager Administration, see the "Using the International Escape Character +" section in the Cisco Unified Communications Manager System Guide.

Maximum Wait Timer for Desktop Call Pickup Does Not Get Applied If Hold DTMF Is Pressed

If a user presses the *81 DTMF code from a remote destination (either a smartphone or any other phone) to put a call on hold, the user desktop phone displays the Resume softkey. The desktop phone does not apply a timer for desktop call pickup, however; the Resume key does not stop displaying after the timeout that is configured for the end user to pick up the call and the call does not get dropped.

Instead, users should hang up the call on the remote phone, which triggers the desktop phone to apply the timer for desktop call pickup. (Use the Maximum Wait Time for Desk Pickup field on the End User Configuration window to change this setting.)

Cisco Unified IP Phones 7940 and 7960 That Are Running SIP

When running SIP, Cisco Unified IP Phones 7940 and 7960 do not support the Remote-in-use state and therefore cannot support desktop call pickup.

For these phones, if the mobile phone user hangs up a call that the Cisco Unified IP Phone 7940 or 7960 that is running SIP extended to the mobile phone, the calling party hears music on hold for ten seconds (as configured by the Maximum Wait Time for Desk Pickup field for the remote destination end user) and then the call drops. Because the desktop call pickup feature does not get supported for these phones when they are running as SIP devices, the user desktop phone does not display the Resume softkey, so the user cannot pick up the call on the desktop phone.

Cisco recommends that you configure Cisco Unified IP Phones 7940 and 7960 to run SCCP for users that are enabled for Cisco Unified Mobility.

Additional Information

See the "Related Topics" section.

System Requirements

Mobile Connect and Mobile Voice Access work with Cisco Unified IP Phones 7906, 7911, 7941/61, 7962/42, 7970/71, 7975 that are running SIP or SCCP. They require the following software components:

Cisco Unified Communications Manager 6.0 or later.

Cisco Unified Mobile Voice Access service, which runs only on the publisher.

Cisco Unified Communications Manager Locale Installer (if you want to use non-English phone locales or country-specific tones).

Additional Information

See the "Related Topics" section.

Migrating from Cisco Unified MobilityManager

Follow this process to migrate standalone Cisco Unified MobilityManager data to Cisco Unified Communications Manager Release 6.0(1) or later:

1. Upgrade the Cisco Unified MobilityManager system to Release 1.2(5), if necessary. See the Release Notes for Cisco Unified MobilityManager Release 1.2(5).

2. Log in to Cisco Unified MobilityManager and export the configuration data in CSV format. For instructions, see the Release Notes for Cisco Unified MobilityManager Release 1.2(5).

3. Log in to Cisco Unified Communications Manager Administration Release 6.0(1) (or later) and use the Bulk Administration Import/Export windows to import the CSV data files that were previously exported from Cisco Unified MobilityManager. Refer to the "Access List," "Remote Destination," and "Remote Destination Profile" chapters in the Cisco Unified Communications Manager Bulk Administration Guide.

Additional Information

See the "Related Topics" section.

Configuring Cisco Unified Mobility

This section provides detailed procedures for each Cisco Unified Communications Manager Administration menu option that must be configured to provision Cisco Unified Mobility features that are native to Cisco Unified Communications Manager.

See the "Configuration Checklist for Cisco Unified Mobility" section for an overview checklist of the procedures and steps that are necessary for an administrator to configure Cisco Unified Mobility features that are native to Cisco Unified Communications Manager.

End users use the Cisco Unified CM User Options windows to further configure or modify the Cisco Unified Mobility settings that apply to their mobile phones.

This section covers the following topics:

Access List Configuration

Remote Destination Profile Configuration

Remote Destination Configuration

Mobile Voice Access Directory Number Configuration

H.323 Gateway Configuration for Enterprise Feature Access

Enterprise Feature Access Two-Stage Dialing

Mobility Setting Configuration

Mobility Softkey Configuration


Tip Before you configure Cisco Unified Mobility, review the "Configuration Checklist for Cisco Unified Mobility" section.


Additional Information

See the "Related Topics" section.

Access List Configuration

You can define access lists to explicitly allow or block the extension of Mobile Connect calls to remote destinations based on the caller ID of the caller.

To configure access lists, see the following sections:

Finding Access Lists

Configuring Access Lists

Deleting Access Lists

Additional Information

See the "Related Topics" section.

Finding Access Lists

An access list, which supports Cisco Unified Mobility, specifies a list that determines the phone numbers that the system can pass or block from being passed to remote destinations. For more information on Cisco Unified Mobility, refer to the "Related Topics" section.

Because you might have several access lists in your network, Cisco Unified Communications Manager lets you locate specific access lists by using specific criteria as the basis. Use the following procedure to locate access lists.


Note During your work in a browser session, Cisco Unified Communications Manager Administration retains your access list search preferences. If you navigate to other menu items and return to this menu item, Cisco Unified Communications Manager Administration retains your access list search preferences until you modify your search or close the browser.


Procedure


Step 1 In the menu bar, choose Call Routing > Class of Control > Access List.

The Find and List Access Lists window displays. Records from an active (prior) query may also display in the window.

Step 2 To find all records in the database, ensure the dialog box is empty; go to Step 3.

To filter or search records

From the first drop-down list box, choose a search parameter.

From the second drop-down list box, choose a search pattern.

Specify the appropriate search text, if applicable.


Note To add additional search criteria, click the + button. When you add criteria, the system searches for a record that matches all criteria that you specify. To remove criteria, click the - button to remove the last added criterion or click the Clear Filter button to remove all added search criteria.


Step 3 Click Find.

All matching records display. You can change the number of items that display on each page by choosing a different value from the Rows per Page drop-down list box.


Note You can delete multiple records from the database by checking the check boxes next to the appropriate record and clicking Delete Selected. You can delete all configurable records for this selection by clicking Select All and then clicking Delete Selected.


Step 4 From the list of records that display, click the link for the record that you want to view.


Note To reverse the sort order, click the up or down arrow, if available, in the list header.


The window displays the item that you choose.


Additional Information

See the "Related Topics" section.

Configuring Access Lists

The following procedure describes how to configure an access list.

Procedure


Step 1 In the menu bar, choose Call Routing > Class of Control > Access List.

The Find and List Access Lists window displays.

Step 2 Perform one of the following tasks:

To copy an existing access list, locate the appropriate access list as described in the "Finding Access Lists" section. Click the Copy icon next to the access list that you want to copy. The window displays the copy of the access list. Change the value in the Name field, and continue with Step 3.

To add a new access list, click the Add New button and continue with Step 3.

To update an existing access list, locate the appropriate access list as described in the "Finding Access Lists" section, and continue with Step 3.

Step 3 Enter values for the parameters that are described in Table 13-4.

Step 4 Click Save.

If you are configuring a new access list, the window reopens to display Access List Member Information area.

Step 5 If you want to configure the members of an access list, click Add Member.

The Access List Member Detail window opens.

Step 6 Enter values for the parameters that are described in Table 13-5.

Step 7 Click Save.

The Access List Configuration window reopens to show the new number or filter in the Selected Filters area.

Step 8 From the Access Configuration window, add additional filters and also modify any existing access list as needed:

To modify a DN mask, click the link for the directory number at the bottom of the window under Access List Members, enter your change, and click Save.

To delete a filter, select the filter and click Delete.

To inactivate a filter without deleting it, select the filter in the Selected Filters pane and click the down arrow to move the filter to the Removed Filters pane.

To activate a filter, select the filter in the Removed Filters pane and click the up arrow to move the filter to the Selected filters area.

To create a new access list with the same members as the existing list, click Copy.


Additional Information

See the "Related Topics" section.

Deleting Access Lists

To delete an access list in Cisco Unified Communications Manager Administration, perform the following procedure.

Before You Begin

You cannot delete access lists that remote destinations are using. To find out which items are using the access list, choose Dependency Records from the Related Links drop-down list box that is on the Access List Configuration window. If the dependency records are not enabled for the system, the dependency records summary window displays a message. For more information about dependency records, see the "Accessing Dependency Records" section. If you try to delete an access list that is in use, Cisco Unified Communications Manager displays a message. Before deleting an access list that is currently in use, you must perform either or both of the following tasks:

Assign a different access list to any remote destinations that are using the access list that you want to delete. See the "Remote Destination Configuration" section.

Delete the remote destinations that are using the access list that you want to delete. See the "Deleting Remote Destinations" section.

Procedure


Step 1 Locate the access list that you want to delete, as described in the "Finding Access Lists" section.

Step 2 After the Access Lists window displays, click Delete.

Step 3 To continue with the deletion, click OK.


Additional Information

See the "Related Topics" section.

Access List Configuration Settings

An access list, which supports Cisco Unified Mobility, specifies a list that determines the phone numbers that the system can pass or block from being passed to remote destinations.

Table 13-4 describes the available settings in the Access List Configuration window. For more information on Cisco Unified Mobility, refer to the "Related Topics" section.

Table 13-4 Access List Configuration Settings 

Field
Description
Access List Information

Name

Enter a unique name (between 1 and 50 characters) for this access list.

You may use all characters except quotes ("), close angle bracket (>), open angle bracket (<), backslash (\), ampersand (&), and percent sign (%).

Description

Enter a text description (between 1 and 128 characters) for this access list.

You may use all characters except nonprinting characters, such as tabs and quotes (").

Owner

From the drop-down list box, choose the end user to whom the access list applies.

Allowed

Click this radio button to allow calls from member phone numbers to be passed to the remote destinations.

Blocked

Click this radio button to block calls from member phone numbers from being passed to the remote destinations.

Access List Member Information

Selected Filters

This pane displays the current members of this access list. Members comprise the following types:

Private—This filter applies to calls that come from private numbers, which do not display caller ID.

Not Available—This filter applies to calls that come from numbers that do not have caller ID.

Directory Number—This filter specifies a directory number that is specified between parentheses. For example, (12345). Valid values include the digits 0 through 9, the wildcard X, !, and #.

Use the arrows below this pane to move the access list members to or from this pane.

Add Member—Click this button to add a new member to the Selected Filters pane. The Add List Member Detail window displays. See the "Access List Member Detail Configuration Settings" section for details.

Removed Filters

This pane specifies filters that have been defined for this access list but that are not currently selected.

Use the arrows above this pane to move the access list members to or from this pane.


Additional Information

See the "Related Topics" section.

Access List Member Detail Configuration Settings

The Access List Member Detail window displays when you click the Add Member button on the Access List Configuration window while you configure an access list. The Access List Member Detail window allows you to configure the following settings for an access list member:

Filter Mask

DN Mask

After you configure a new access list member, the new access list member displays in the Access List Members pane at the bottom of the corresponding Access List Configuration window. You can click one of the access list members to view or change the settings for that access list member. To exit the Access List Member Detail window without making any changes, choose Back to Find/List from the Related Links drop-down list box and click Go.

Table 13-5 describes the available settings in the Access List Member Detail window.

Table 13-5 Access List Member Detail Configuration Settings 

Field
Description

Filter Mask

Select an option from the drop-down list box. You can choose to enter a directory number, filter out calls that do not have caller ID (Not Available), or specify a number that will be allowed or blocked without displaying the caller ID (Private).

DN Mask

If you chose Directory Number in the Filter Mask field, enter a phone number or filter in the DN Mask field. You can use the following wild cards to define a filter:

X (upper or lower case)—Matches a single digit.

!—Matches any number of digits.

#—Used as a single digit for exact match.

Examples:

408! matches any number that starts with 408.

408555123X matches any number between 4085551230 and 4085551239.

Note If you want to filter an incoming call from a calling number that begins with a leading +, you must include the leading + in the DN Mask field unless any supported wild card prefixes the directory number. For example, if an end user wants to block +14081239876, the user access list needs to include either +14081239876 or !14081239876 in the DN Mask field.


Additional Information

See the "Related Topics" section.

Remote Destination Profile Configuration

To configure remote destination profiles, see the following sections:

Finding Remote Destination Profiles

Configuring a Remote Destination Profile

Associating a Directory Number with a Remote Destination Profile

Deleting Remote Destination Profiles

Remote Destination Profile Configuration Settings

Additional Information

See the "Related Topics" section.

Finding Remote Destination Profiles

Remote destination profiles, which support Cisco Unified Mobility, specify a set of parameters that apply to all remote destinations for the user. For more information on Cisco Unified Mobility, see the "Related Topics" section.

Because you might have several remote destination profiles in your network, Cisco Unified Communications Manager lets you locate specific remote destination profiles by using specific criteria as the basis. Use the following procedure to locate remote destination profiles.


Note During your work in a browser session, Cisco Unified Communications Manager Administration retains your remote destination profile search preferences. If you navigate to other menu items and return to this menu item, Cisco Unified Communications Manager Administration retains your remote destination profile search preferences until you modify your search or close the browser.


Procedure


Step 1 In the menu bar, choose Device > Device Settings > Remote Destination Profile.

The Find and List Remote Destination Profiles window displays. Records from an active (prior) query may also display in the window.

Step 2 To find all records in the database, ensure the dialog box is empty; go to Step 3.

To filter or search records

From the first drop-down list box, choose a search parameter.

From the second drop-down list box, choose a search pattern.

Specify the appropriate search text, if applicable.


Note To add additional search criteria, click the + button. When you add criteria, the system searches for a record that matches all criteria that you specify. To remove criteria, click the - button to remove the last added criterion or click the Clear Filter button to remove all added search criteria.


Step 3 Click Find.

All matching records display. You can change the number of items that display on each page by choosing a different value from the Rows per Page drop-down list box.


Note You can delete multiple records from the database by checking the check boxes next to the appropriate record and clicking Delete Selected. You can delete all configurable records for this selection by clicking Select All and then clicking Delete Selected.


Step 4 From the list of records that display, click the link for the record that you want to view.


Note To reverse the sort order, click the up or down arrow, if available, in the list header.


The window displays the item that you choose.


Additional Information

See the "Related Topics" section.

Configuring a Remote Destination Profile

The remote destination profile contains the parameters that apply to all remote destinations for the user. After configuring user accounts for Mobile Connect (refer to the "End User Configuration" chapter in the Cisco Unified Communications Manager Administration Guide), you can create a remote destination profile for the user.

To configure a remote destination profile, perform the following procedure:

Procedure


Step 1 In the menu bar, choose Device > Device Settings > Remote Destination Profile.

Step 2 Perform one of the following tasks:

To copy an existing remote destination profile, locate the appropriate remote destination profile as described in the "Finding Remote Destination Profiles" section. Click the Copy icon next to the remote destination profile that you want to copy. The window displays the copy of the remote destination profile. Change the value in the Name field and continue with Step 3.

To add a new remote destination profile, click the Add New button and continue with Step 3.

To update an existing remote destination profile, locate the appropriate remote destination profile as described in the "Finding Remote Destination Profiles" section and continue with Step 3.

Step 3 Enter the appropriate settings as described in Table 13-6.

Step 4 Click Save.


Additional Information

See the "Related Topics" section.

Associating a Directory Number with a Remote Destination Profile

After creating a remote destination profile, you must associate the DN record for the desktop phone or phones for the user. Click the Add a New DN link on the Remote Destination Profile Configuration window and follow the instructions in the "Directory Number Configuration" chapter of the Cisco Unified Communications Manager Administration Guide.


Note If the remote destination profile is dissociated on the Directory Number configuration window, you must check the Line Association check box for the DN on the Remote Destination window to reassociate it.


Additional Information

See the "Related Topics" section.

Deleting Remote Destination Profiles

To delete a remote destination profile in Cisco Unified Communications Manager Administration, perform the following procedure.

Before You Begin

You can delete remote destination profiles that associate with remote destinations. You receive a warning message that you are about to delete both a remote destination profile and the associated remote destinations.

To find out which items are using the remote destination profiles, choose Dependency Records from the Related Links drop-down list box that is on the Remote Destination Profile Configuration window. If the dependency records are not enabled for the system, the dependency records summary window displays a message. For more information about dependency records, see the "Accessing Dependency Records" section.

Procedure


Step 1 Locate the remote destination profile that you want to update, as described in the "Finding Remote Destination Profiles" section.

Step 2 After the Remote Destination Profiles window displays, click Delete.

Step 3 To continue with the deletion, click OK.


Remote Destination Profile Configuration Settings

Remote destination profiles, which support Cisco Unified Mobility, specify a set of parameters that apply to all remote destinations for the user. For more information on Cisco Unified Mobility, see the "Related Topics" section.

Table 13-6 describes the available settings in the Remote Destination Profile Configuration window.

Table 13-6 Remote Destination Profile Configuration Settings 

Field
Description
Remote Destination Profile Information

Name

Enter a text name for the remote destination profile.

Description

Enter a text description of the remote destination profile.

User ID

Choose the user to whom this profile is assigned. The selection must match the ID of a user in the End User Configuration window where Enable Mobility is checked.

Device Pool

Choose the device pool that applies to this profile. The device pool defines sets of common characteristics for devices, such as region, date/time group, softkey template, and MLPP information.

Calling Search Space

Choose the calling search space to be used for routing Mobile Voice Access or Enterprise Feature Access calls.

Note This calling search space setting applies only when you are routing calls from the remote destination, which specifies the outbound call leg to the dialed number for Mobile Voice Access and Enterprise Feature Access calls.

User Hold Audio Source

Choose the audio option for users on hold for Mobile Connect and Mobile Voice Access calls.

Network Hold MOH Audio Source

Choose the audio source from the IOS gateway that provides multicasting audio source for Mobile Connect and Mobile Voice Access calls.

Privacy

Choose a privacy option for the remote destination profile.

If you choose the Default value for this field, the setting matches the value of the Privacy Setting service parameter.

Note If you change and save the value of the Privacy Setting service parameter, you must return to the Remote Destination Profile Configuration window for a remote destination profile that specifies Default and click Save for the service parameter change to take effect.

For more configuration information, refer to Barge and Privacy in the Cisco Unified Communications Manager Features and Services Guide.

Rerouting Calling Search Space

Choose a calling search space to be used to route Mobile Connect calls.

Note Ensure that the gateway that is configured for routing mobile calls is assigned to the partition that belongs to the Rerouting Calling Search Space. Cisco Unified Communications Manager determines how to route calls based on the remote destination number and the Rerouting Calling Search Space.

Note The Rerouting Calling Search Space setting applies only when you are routing calls to the remote destination or mobility identity, which specifies the outbound call leg toward the remote destination or mobility identity when a call comes in to the user enterprise number.

Note Mobile Connect calls do not get routed to the dual-mode mobility identity number that corresponds to the dual-mode mobile phone number if the device associates with the enterprise WLAN and registers with Cisco Unified Communications Manager. Mobile Connect calls get routed to the dual-mode mobility identity number only when the device is outside the enterprise.

Calling Party Transformation CSS

Choose the calling search space for transformations. This setting allows you to localize the calling party number on the device. Make sure that the Calling Party Transformation CSS that you choose contains the calling party transformation pattern that you want to assign to this device.

Note The partitions in the calling search space should contain only calling party transformations.

Note Ensure the calling search space is not null because no transformations can apply to null partitions.

Note The device takes on the attributes of the Calling Party Transformation Pattern because you assign the pattern to a partition where the Calling Party Transformation CSS exists. For example, when you configure the Calling Party Transformation CSS under Call Routing > Class of Control > Calling Search Space, you assign the CSS to a partition; when you configure the Calling Party Transformation CSS under Call Routing > Transformation Pattern > Calling Party Transformation Pattern, you choose the partition where the Calling Party Transformation CSS is assigned.

Use Device Pool Calling Party Transformation CSS

To use the Calling Party Transformation CSS that is configured in the device pool that is assigned to this device, check this check box. If you do not check this check box, the device uses the Calling Party Transformation CSS that you configured in the Remote Destination Profile Configuration window.

User Locale

From the drop-down list box, choose the locale that is associated with the phone user interface. The user locale identifies a set of detailed information, including language and font, to support users.

Cisco Unified Communications Manager makes this field available only for phone models that support localization.

Note If the users require information to display (on the phone) in any language other than English, verify that the locale installer is installed before you configure user locale. Refer to the Cisco Unified Communications Manager Locale Installer documentation.

Ignore presentation indicators (internal calls only)

Check the check box if you want to ignore the connected line ID presentation. Use this configuration for internal calls.

Associated Remote Destinations

Add a New Remote Destination

Click this link to open the Remote Destination Configuration window, where you can configure a new remote destination to associate with this remote destination profile. By default, the current remote destination profile is selected in the Remote Destination Profile field of the new remote destination. Refer to the "Remote Destination Configuration" section for details.

Name

For a remote destination that already exists and has been associated with this remote destination profile, this column displays the name of the remote destination.

Destination Number

For a remote destination that already exists and has been associated with this remote destination profile, this column displays the destination number of the remote destination.

Do Not Disturb

Do Not Disturb

Check this check box to enable Do Not Disturb on the phone.

DND Option

This Call Reject option specifies that no incoming call information gets presented to the user.

Note For mobile devices, dual-mode phones, and phones that are running SCCP, you can only choose the Call Reject option. When you activate DND Call Reject on a mobile device or dual-mode phone, no call information gets presented to the device.


Additional Information

See the "Related Topics" section.

Remote Destination Configuration

After remote destination profiles and access lists are created, you can enter individual remote destinations and assign each to a profile. Each remote destination represents a mobile or other phone that can be configured to perform remote destination pickup (accept transfers from the desktop phone of the user) and accept incoming Mobile Connect calls that come from the system as a result of the line that is shared with the desktop phone.

After you save a new remote destination, the Association Information pane displays in the window. This section lists the desktop phone numbers that have been assigned to the remote destination profile. You can click a link to open the associated Directory Number Information window. See "Configuring a Directory Number" in the Cisco Unified Communications Manager Administration Guide.


Note This section describes how to access remote destination records by opening the Remote Destination Configuration window. You can also open an existing or new record in the Remote Destination Profile Configuration window by clicking the Add a New Remote Destination link at the bottom of the remote destination profile. See the "Finding Remote Destination Profiles" section for instructions on displaying a remote destination profile.


To configure remote destinations, refer to the following sections:

Finding Remote Destinations

Configuring Remote Destinations

Deleting Remote Destinations

Remote Destination Configuration Settings

Additional Information

See the "Related Topics" section.

Finding Remote Destinations

Remote destinations represent phones that are available for Mobile Connect answer and pickup, plus locations that are used to reach Mobile Voice Access. Remote destinations may include any of the following devices:

Single-mode mobile (cellular) phones

Smartphones

Dual-mode phones

Enterprise IP phones that are not in the same cluster as the desktop phone

Home phone numbers in the PSTN.

For more information on Cisco Unified Mobility, see the "Related Topics" section.

Because you might have several remote destinations in your network, Cisco Unified Communications Manager lets you locate specific remote destinations by using specific criteria as the basis. Use the following procedure to locate remote destinations.


Note During your work in a browser session, Cisco Unified Communications Manager Administration retains your remote destination search preferences. If you navigate to other menu items and return to this menu item, Cisco Unified Communications Manager Administration retains your remote destination search preferences until you modify your search or close the browser.


Procedure


Step 1 In the menu bar, choose Device > Remote Destination.

The Find and List Remote Destinations window displays. Records from an active (prior) query may also display in the window.

Step 2 To find all records in the database, ensure the dialog box is empty; go to Step 3.

To filter or search records

From the first drop-down list box, choose a search parameter.

From the second drop-down list box, choose a search pattern.

Specify the appropriate search text, if applicable.


Note To add additional search criteria, click the + button. When you add criteria, the system searches for a record that matches all criteria that you specify. To remove criteria, click the - button to remove the last added criterion or click the Clear Filter button to remove all added search criteria.


Step 3 Click Find.

All matching records display. You can change the number of items that display on each page by choosing a different value from the Rows per Page drop-down list box.


Note You can delete multiple records from the database by checking the check boxes next to the appropriate record and clicking Delete Selected. You can delete all configurable records for this selection by clicking Select All and then clicking Delete Selected.


Step 4 From the list of records that display, click the link for the record that you want to view.


Note To reverse the sort order, click the up or down arrow, if available, in the list header.


The window displays the item that you choose.


Additional Information

See the "Related Topics" section.

Configuring Remote Destinations


Note End users can create their own remote destinations in the Cisco Unified CM User Options windows. For information on how to perform this task, refer to the user guide for the phone model.


To add configure a remote destination, perform the following procedure:

Procedure


Step 1 In the menu bar, choose Device > Remote Destination.

The Remote Destination Configuration window displays.

Step 2 Perform one of the following tasks:

To copy an existing remote destination, locate the appropriate remote destination as described in the "Finding Remote Destinations" section. Click the Copy icon next to the remote destination that you want to copy. The window displays the copy of the remote destination. Change the value in the Name field and continue with Step 3.

To add a new remote destination, click the Add New button and continue with Step 3.

To update an existing remote destination, locate the appropriate remote destination as described in the "Finding Remote Destinations" section and continue with Step 3.

Step 3 Enter the appropriate settings as described in Table 13-7.


Note Be aware that the appropriate timer settings in Table 13-7 may be vendor-specific. If difficulties in transferring calls by using the default timer settings occur, you may need to adjust the settings to be compatible with the vendor of the remote destination phone.


Step 4 Check the Line Association check boxes for the desktop phones that will be used with this remote destination. You must perform this step for Mobile Connect to work.


Note This step requires that a directory number has already been configured on the remote destination profile with which the remote destination associates.


Step 5 Click Save.


Additional Information

See the "Related Topics" section.

Deleting Remote Destinations

To delete a remote destination in Cisco Unified Communications Manager Administration, perform the following procedure.

Before You Begin

To find out which items are using the remote destination, choose Dependency Records from the Related Links drop-down list box that is on the Remote Destination Configuration window. If the dependency records are not enabled for the system, the dependency records summary window displays a message. For more information about dependency records, see the "Accessing Dependency Records" section.

Procedure


Step 1 In the menu bar, choose Device > Remote Destination.

The Remote Destination Configuration window displays.

Step 2 Locate the remote destination that you want to delete, as described in the "Finding Remote Destinations" section.

Step 3 After the Remote Destination Configuration window displays, click Delete.

Step 4 To continue with the deletion, click OK.


Additional Information

See the "Related Topics" section.

Remote Destination Configuration Settings

Remote destinations represent phones that are available for Mobile Connect responses and pickup, plus locations that are used to reach Mobile Voice Access. Remote destinations may include any of the following devices:

Single-mode mobile (cellular) phones

Smartphones

Dual-mode phones

Enterprise IP phones that are not in the same cluster as the desktop phone

Home phone numbers in the PSTN.

For more information on Cisco Unified Mobility, see the "Related Topics" section.

Table 13-7 describes the available settings in the Remote Destination Configuration window.

Table 13-7 Remote Destination Configuration Settings 

Field
Description
Remote Destination Information
Mobile Identity Information

Name

Enter a name that identifies the remote destination.

Destination Number

Enter the telephone number for the destination. Include the area code and any additional digits that are required to obtain an outside line. Maximum field length equals 24 characters; individual characters can take the values 0-9, *, #, and +. Cisco recommends that you configure the caller ID of the remote destination.

Note Add the necessary translation pattern or route patterns to route the destination number.

For the SIP URI feature, you can also enter a Universal Resource Indicator (URI) in this field, such as user@corporation.com, up to 126 characters in length. Keep in mind that a SIP route pattern must also be configured.

If the administrator configures the Incoming Calling Party settings in the Cisco Unified Communications Manager gateway, trunk, or device pool to globalize the incoming calling party number, configure the Destination Number of the remote destination in the E.164 format.

Example: For a remote destination with US area code 408 and destination number 5552222, configure the Destination Number as +14085552222.

Additionally, if globalized destination numbers are in use, set the Matching Caller ID with Remote Destination service parameter to Complete Match.

Answer Too Soon Timer

Enter the minimum time in milliseconds that Cisco Unified Communications Manager requires the mobile phone to ring before answering the call. This setting accounts for situations where the mobile phone is switched off or is not reachable, in which case the network may immediately divert the call to the mobile phone voice mail. If the mobile phone is answered before this timer expires, Cisco Unified Communications Manager pulls the call back to the enterprise.

Range: 0 - 10,000 milliseconds

Default: 1,500 milliseconds

Answer Too Late Timer

Enter the maximum time in milliseconds that Cisco Unified Communications Manager allows for the mobile phone to answer. If this value is reached, Cisco Unified Communications Manager stops ringing the mobile phone and pulls the call back to the enterprise.

Range: 10,000 - 300,000 milliseconds

Default: 19,000 milliseconds

Delay Before Ringing Timer

Enter the time that elapses before the mobile phone rings when a call is extended to the remote destination.

Range: 0 - 30,000 milliseconds

Default: 4,000 milliseconds

Tip When a hunt group is in use, the lines ring only for a short period of time. You may need to manipulate the Delay Before Ringing Timer setting and make it zero to allow a remote destination call to be established, ring, and answer, before the hunt list timer expires and pulls the call back.

Remote Destination Profile

From the drop-down list box, choose the remote destination profile that you want to use for this remote destination.

Cisco Unified Mobile Communicator

This field displays the Cisco Unified Mobile Communicator device with which this Mobility Identity associates. Click the Configure Device link to display the Phone Configuration window, where you can change the settings of the specified device.

Dual Mode Phone

This field displays a dual-mode phone with which this Mobility Identity associates. The field displays the device name. Click the Configure Device link to display the Phone Configuration window, where you can change the settings of the specified device.

Mobile Phone

Check the check box if you want calls that the desktop phone answers to be sent to your mobile phone as the remote destination.

Checking this check box ensures that, if Send Call to Mobile Phone is specified (by using the Mobility softkey for remote destination pickup), the call gets extended to this particular remote destination.

Note This check box does not apply to dual-mode phones that are running SIP, such as DoCoMo N902iL and DoCoMo N906i, nor to dual-mode phones that are running SCCP, such as Nokia S60.

Enable Mobile Connect

Check the check box to allow an incoming call to ring your desktop phone and remote destination at the same time.

When Mobile Connect Is Enabled
Ring Schedule

All the time

If the Enable Mobile Connect check box is checked for this remote destination, clicking this radio button allows this remote destination to ring all the time. This setting works in conjunction with the setting in the When receiving a call during the above ring schedule pane below.

As specified below

If the Enable Mobile Connect check box is checked for this remote destination, clicking this radio button allows this remote destination to ring according to the schedule that the subsequent rows specify. This setting works in conjunction with the setting in the When receiving a call during the above ring schedule pane below.

(day of week)

If the Enable Mobile Connect check box is checked and the As specified below radio button is selected, click the check box for each day of the week when the remote destination should receive calls. You can specify a ring schedule for each day of the week.

(day of the week)—Check the check box for a day of the week, such as Monday, to specify the ring schedule for that day.

All Day—Click this check box next to a day of the week to specify that the remote destination should ring at all hours of the day as specified by the setting in the When receiving a call during the above ring schedule pane below.

(drop-down list box) to (drop-down list box)—For a particular day of the week, specify a ring schedule by choosing a starting time and ending time for that day. Specify the starting time by choosing a value in the drop-down list box that precedes to and specify the ending time by choosing a value in the drop-down list box that follows to. For a particular day, the default ring schedule specifies No Office Hours. The values that you specify in the drop-down list boxes relate to the time zone that you specify in the Time Zone field for the remote destination.

Time Zone

From the drop-down list box, choose a time zone to use for this remote destination.

Note The time-of-day access feature uses the time zone that you choose for this remote destination to allow or block calls to this remote destination.

When receiving a call during the above ring schedule

Always ring this destination

Click this radio button to cause incoming calls to always ring this remote destination according to the Ring Schedule that you specify. This setting applies only if the Enable Mobile Connect check box is checked for this remote destination.

Ring this destination only if caller is in

Click this radio button to allow incoming calls to ring this remote destination only if the caller belongs to the access list that is specified in the drop-down list box and according to the Ring Schedule that you specify in the Ring Schedule pane. This setting applies only if the Enable Mobile Connect check box is checked for this remote destination.

From the drop-down list box, choose an access list that applies to this setting. If you want to view the details of an access list, click the View Details link. (To modify an access list, you must use the Call Routing > Class of Control > Access List menu option.)

Choosing an access list that contains no members equates to choosing to never ring this destination.

Do not ring this destination if caller is in

Click this radio button to prevent incoming calls from ringing this remote destination if the caller belongs to the access list that is specified in the drop-down list box and according to the Ring Schedule that you specify in the Ring Schedule pane. This setting applies only if the Enable Mobile Connect check box is checked for this remote destination.

From the drop-down list box, choose an access list that applies to this setting. If you want to view the details of an access list, click the View Details link. (To modify an access list, you must use the Call Routing > Class of Control > Access List menu option.)

Choosing an access list that contains no members equates to choosing the Always ring this destination radio button.

Association Information

Line

This entry displays a line that can associate with this remote destination.

Line Association

Check this check box if you want to associate a particular line with this remote destination. You must check a line association check box for Mobile Connect to work for this remote destination.

Note Be aware that the line association check box of a line must be checked for Mobile Connect calls to ring this remote destination when a call comes into the directory number that is assigned to that particular line.


Additional Information

See the "Related Topics" section.

Mobile Voice Access Directory Number Configuration

Use the Mobile Voice Access window under Media Resources to assign sets of localized user prompts for Mobile Voice Access.

This configuration is required for making calls with the Mobile Voice Access feature. After the gateway collects the required digits from the user to make a call, the call gets transferred to the DN that is configured in this window. This DN can be an internal DN to Cisco Unified Communications Manager and the end user does not need to know the DN. The administrator must configure a dial-peer so that the MVA service can transfer the call from the gateway to this DN. This DN should be also be placed in a partition where the inbound calling search space (CSS) of the gateway or the remote destination profile CSS can reach the DN, as configured in the Inbound Calling Search Space for Remote Destination service parameter in the Clusterwide Parameters (System - Mobility) pane.

To assign localized users prompts for Mobile Voice Access, perform the following procedure:

Procedure


Step 1 In the menu bar, choose Media Resources > Mobile Voice Access.

Step 2 Enter values for the parameters that are described in Table 13-8.

Step 3 Click Save.


Additional Information

See the "Related Topics" section.

Mobile Voice Access Configuration Settings

Table 13-8 describes the available settings in the Mobile Voice Access window.

For more information on Cisco Unified Mobility, see the "Related Topics" section.

Table 13-8 Mobile Voice Access Configuration Settings 

Field
Description
Mobile Voice Access Information

Mobile Voice Access Directory Number

Enter the internal DN to receive Mobile Voice Access calls from the gateway.

Mobility patterns accept up to 24 digits and allow the following characters: numeric (0 through 9), letters (A through D), plus sign (+), octothorpe (#), and asterisk (*). You must precede the plus sign (+) with a backslash (\).

Mobile Voice Access Partition

From the drop-down list box, choose a partition for Mobile Voice Access. The combination of directory number and partition makes the Mobile Voice Access directory number unique.

Mobile Voice Access Localization

Available Locales

This pane displays the locales that have been configured. Refer to the Cisco Unified Communications Manager Locale Installer documentation for details.

Use the Down Arrow key to move the locales that you select to the Selected Locales pane.

Note Cisco Unified Mobility supports a maximum of nine locales. If more than nine locales are installed for Cisco Unified Communications Manager, they will display in the Available Locales pane, but you can only save up to nine locales in the Selected Locales pane. If you attempt to configure more than nine locales for Cisco Unified Mobility, the following message displays: "Update failed. Check constraint (informix.cc_ivruserlocale_orderindex) failed."

Selected Locales

Use the arrows above this pane to move the locales that you want to select to or from this pane.

Note Remember that you can select a maximum of nine locales, even if more locales are available in the system.

Use the arrow keys to the right of this pane to reorder the locales that are listed in the pane. Choose a locale by clicking the locale name; then, use the arrow key to change the order of the chosen locale.

Note Mobile Voice Access uses the first locale that displays in the Selected Locales pane in the Mobile Voice Access window when the IVR is used. For example, if English United States displays first in the Selected Locales pane, the Cisco Unified Mobility user receives English when the IVR is used during a call.


Additional Information

See the "Related Topics" section.

H.323 Gateway Configuration for Enterprise Feature Access

To configure H.323 gateways for Enterprise Feature Access, two options are available:

Configuring an H.323 Gateway for System Remote Access

Configuring an H.323 Gateway for System Remote Access by Using Hairpinning

Additional Information

See the "Related Topics" section.

Configuring an H.323 Gateway for System Remote Access

If you already have an H.323 gateway that is configured in Cisco Unified Communications Manager, you can use it to support system remote access. If you do not have an H.323 gateway, you must add and configure one. For more information, refer to the "Adding a Cisco IOS H.323 Gateway" section in the Cisco Unified Communications Manager Administration Guide.


Note When a Mobile Connect call is placed from an internal extension, the system presents only the internal extension as the caller ID. If an H.323 gateway is used, you can use translation patterns to address this issue.


To configure the gateway, follow these steps.

Procedure


Step 1 Configure the T1/E1 controller for PRI from PSTN.

Sample configuration:

controller T1 1/0

framing esf

linecode b8zs

pri-group timeslots 1-24

Step 2 Configure the serial interface for the PRI (T1/E1).

Sample configuration:

interface Serial 1/0:23

ip address none

logging event link-status none

isdn switch-type primary 4ess

isdn incoming-voice voice

isdn bchan-number-order ascending

no cdp enable

Step 3 Load the VXML application from the Cisco Unified Communications Manager server (Publisher).

Sample configuration for IOS Version 12.3 (13) and later:

application service CCM

http://<Unified CM Publisher IP Addr>:8080/ccmivr/pages/IVRMainpage.vxml

Sample configuration before IOS Version 12.3(12):

call application voice Unified CCM

http://<Unified CM Publisher IP Addr>:8080/ccmivr/pages/IVRMainpage.vxml


Note Although VXML was added in Version 12.2(11), Versions 12.3(8), 12.3(9), 12.3(14)T1, and 12.2(15) have VXML issues, and you should not be use them.


Step 4 Configure the dial-peer to associate Mobile Connect application with system remote access.

Sample configuration for IOS 12.3(13) and later:

dial-peer voice 58888 pots

service CCM (Mobile Connect VXML application)

incoming called-number 58888

no digit-strip

Sample configuration for IOS 12.3(12) and earlier:

dial-peer voice 100 pots

application CCM (Mobile Connect VXML application)

incoming called-number 58888 (where 58888 represents the Mobile Voice Access number)

no digit-strip

Step 5 Add a dial-peer to transfer the calls to the Mobile Voice Access DN that is configured in the "Mobile Voice Access Directory Number Configuration" section.

Sample configuration for primary Cisco Unified Communications Manager:

dial-peer voice 101 voip

preference 1

destination-pattern <Mobile Voice Access DN>


Note This specifies the Mobile Voice Access DN that is configured with the Media Resources > Mobile Voice Access menu option. If a generic dial-peer is already configured to terminate the calls and is consistent with the Mobile Voice Access DN, you do not need to perform this step.


session target ipv4:10.1.30.3

codec g711ulaw

dtmf-relay h245-alphanumeric

no vad

Sample configuration for secondary Cisco Unified Communications Manager (if needed):

dial-peer voice 102 voip

preference 2

destination-pattern <Mobile Voice Access DN>


Note This specifies the Mobile Voice Access DN that is configured with the Media Resources > Mobile Voice Access menu option. If a generic dial-peer is already configured to terminate the calls and is consistent with the Mobile Voice Access DN, you do not need to perform this step.


session target ipv4:10.1.30.4

codec g711ulaw

dtmf-relay h245-alphanumeric

no vad


Additional Information

See the "Related Topics" section.

Configuring an H.323 Gateway for System Remote Access by Using Hairpinning

If you do not have an H.323 gateway but want to use a H.323 gateway only to support System Remote Access, you must add and configure the gateway. For more information, refer to the "Adding a Cisco IOS H.323 Gateway" section in the Cisco Unified Communications Manager Administration Guide.

To configure the gateway, follow these steps.

Procedure


Step 1 Load the VXML application from the Cisco Unified Communications Manager server (Publisher).

Sample configuration for IOS Version 12.3 (13) and later:

application service CCM

http://<Unified CM Publisher IP Addr>:8080/ccmivr/pages/IVRMainpage.vxml

Sample configuration before IOS Version 12.3(12):

call application voice Unified CCM

http://<Unified CM Publisher IP Addr>:8080/ccmivr/pages/IVRMainpage.vxml


Note Although VXML was added in Version 12.2(11), Versions 12.3(8), 12.3(9), 12.3(14)T1, and 12.2(15) have VXML issues, and you should use them.


Step 2 Configure the dial-peer to associate Mobile Connect application with system remote access.

Sample configuration for IOS 12.3(13) and later:

dial-peer voice 1234567 voip

service CCM

incoming called-number 1234567

codec g711u

session target ipv4:<ip_address of call manager>

Sample configuration for IOS 12.3(12) and earlier:

dial-peer voice 1234567 voip

application CCM

incoming called-number 1234567

codec g711u

session target ipv4:<ip_address of call manager>

Step 3 Add a dial-peer for transferring calls to the Mobile Voice Access DN that is configured in the "Mobile Voice Access Directory Number Configuration" section.

Sample configuration for primary Cisco Communications Manager:

dial-peer voice 101 voip

preference 1

destination-pattern <Mobile Voice Access DN>


Note This specifies the Mobile Voice Access DN that is configured with the Media Resources > Mobile Voice Access menu option. If a generic dial-peer is already configured to terminate the calls and is consistent with the Mobile Voice Access DN, you do not need to perform this step.


session target ipv4:10.1.30.3

voice-class h323 1

codec g711ulaw

dtmf-relay h245-alphanumeric

no vad

Sample configuration for secondary Cisco Communications Manager (if needed):

dial-peer voice 102 voip

preference 2

destination-pattern <Mobile Voice Access DN>


Note This specifies the Mobile Voice Access DN that is configured with the Media Resources > Mobile Voice Access menu option. If a generic dial-peer is already configured to terminate the calls and is consistent with the Mobile Voice Access DN, you do not need to perform this step.


session target ipv4:10.1.30.4

voice-class h323 1

codec g711ulaw

dtmf-relay h245-alphanumeric

no vad

Step 4 Configure hairpin.

voice service voip

allow-connections h323 to h323


Additional Information

See the "Related Topics" section.

Enterprise Feature Access Two-Stage Dialing

To configure enterprise feature access two-stage dialing, use the following procedure.

Procedure


Step 1 Choose System > Service Parameters.

Step 2 For the Cisco CallManager service, set the following service parameters in the Clusterwide Parameters (System - Mobility) area:

Set the Enable Enterprise Feature Access service parameter to True.

Set the Matching Caller ID for Remote Destination service parameter. Choose either Complete Match or Partial Match. If you choose Partial Match, proceed to set a value for the Number of Digits for Caller ID Partial Match service parameter.

If you set the Matching Caller ID for Remote Destination service parameter to Partial Match, set the Number of Digits for Caller ID Partial Match service parameter.

Step 3 To save the service parameter settings, click Save.

Step 4 Choose Call Routing > Mobility Configuration.

Step 5 In the Mobility Configuration window, configure the Enterprise Feature Access DID by specifying a value in the Enterprise Feature Access Directory Number field. (This field specifies the same DID that is called to invoke midcall features like Transfer and Conference.)

Step 6 Specify the partition by choosing a value for the Enterprise Feature Access Directory Number Partition.

Step 7 To save the Mobility Configuration settings, click Save.


When a caller calls the Enterprise Feature Access DID, Cisco Unified Communications Manager matches the calling number to the destination number that is configured in the Remote Destination Configuration window. In the scenario where Cisco Unified Communications Manager Administration prepends the digit 9 to get an outside line, the administrator can manipulate the quantity of digits of this number by modifying these service parameters in the Clusterwide Parameters (System - Mobility) section:

Matching Caller ID with Remote Destination

Number of Digits for Caller ID Partial Match

No IVR exists with this configuration, so callers do not receive a prompt.

Refer to the User Guide of the remote phone model for the steps that users perform to make outbound calls and to use Mobile Voice Access. Keep in mind that, when you use Enterprise Feature Access, each entry must end with the # (octothorpe) character.


Note When configuring the Enterprise Feature Access Directory Number with the Call Routing > Mobility Configuration window, you must configure the Handoff Number field to save the configuration. To save the Enterprise Feature Access Directory Number, be sure to enter a value in the Handoff Number field, such as a dummy or unused number, and save the values in this window.



Note When calling the Mobile Voice Access DN or Enterprise Feature Access DN, the gateway device must present the exact number of digits that are configured as the Mobile Voice Access DN or Enterprise Feature Access DN. Translation patterns or other called number modification cannot be used to match the MVA or EFA numbers either by stripping digits or by adding digits to the number that the gateway presents. Because Cisco Unified Mobility intercepts the call at the gateway layer, the feature behaves thus by design.



Note Unlike Mobile Voice Access (MVA), Enterprise Feature Access (EFA) identifies the user based solely on caller ID. If the system receives no inbound caller ID or receives a value that does not match a remote destination, the EFA call fails. With MVA, if the caller ID does not match, the user gets prompted to enter the user remote destination number. EFA does not provide this capability because no IVR prompts exist. In both cases, after the user is identified, the user authenticates by using the same PIN number.


Additional Information

See the "Related Topics" section.

Mobility Setting Configuration

To configure mobility settings for handoff of dual-mode phones between the Wi-Fi and Global System for Mobile communication (GSM) or Code Division Multiple Access (CDMA) networks, perform the following procedure.

Procedure


Step 1 Choose Call Routing > Mobility Configuration.

The Mobility Configuration window displays.

Step 2 Enter the appropriate settings as described in Table 13-9.

Step 3 Click Save.


Additional Information

See the "Related Topics" section.

Mobility Configuration Settings

The Mobility Configuration window allows you to configure mobility settings for handoff of dual-mode phones between the Wi-Fi and Global System for Mobile communication (GSM) or Code Division Multiple Access (CDMA) networks.

Table 13-9 describes the available settings in the Mobility Configuration window. For more information on Cisco Unified Mobility, see the "Related Topics" section.

Table 13-9 Mobility Configuration Settings 

Field
Description

Handoff Number

Enter the DID number for handoff between the Wi-Fi and GSM or CDMA networks. The handoff feature requires this number.

Handoff Number Partition

From the drop-down list box, choose the partition to which the handoff direct inward dial (DID) belongs.

Enterprise Feature Access Directory Number

Enter the DID number that is required for enterprise feature access. This number supports transfer, conference, resume, and two-stage dialing from smartphones.

Note Ensure that each DID number is unique.

Enterprise Feature Access Directory Number Partition

From the drop-down list box, choose the partition of the DID that is required for enterprise feature access.


Additional Information

See the "Related Topics" section.

Mobility Softkey Configuration

To configure a Mobility softkey for the phone user that uses Mobile Connect, perform the following procedure:

Procedure


Step 1 Choose Device > Device Settings > Softkey Template.

Step 2 To list the existing templates, click Find.

Step 3 To create the new template, click Standard User and then click Copy.

Step 4 Enter a name and description for the Softkey template and click Save.

Step 5 Select Configure Software Layout from the Go next to Related Link menu in the upper, right corner of the window and click Go.

Step 6 Select On Hook from the pull-down list box.

Step 7 Add Mobility to the selected Softkeys and click Save.

Step 8 Select Connected from the pull-down list box.

Step 9 Add Mobility to the selected Softkeys and click Save.

Step 10 Open the Phone Configuration window and associate the Softkey Template with the created Softkey template. See "Configuring Cisco Unified IP Phones" in the Cisco Unified Communications Manager Administration Guide.

Step 11 Choose the Owner User ID for the Mobile Connect phone user.

Step 12 Click Save.


Additional Information

See the "Related Topics" section.

Related Topics

Configuration Checklist for Cisco Unified Mobility

Introducing Cisco Unified Mobility

Definitions

List of Cisco Unified Mobility Features

Other Benefits of Cisco Unified Mobility Features

Mobile Connect

Mobile Voice Access

Time-of-Day Access

Time-of-Day Access Configuration

Important Notes for Time-of-Day Access

Directed Call Park via DTMF

SIP URI Dialing

Use Case Scenarios for Cisco Unified Mobility Features

Interactions and Restrictions

Licensing

Number of Supported Calls

Auto Call Pickup

System Requirements

Migrating from Cisco Unified MobilityManager

Configuring Cisco Unified Mobility

Configuration Checklist for Cisco Unified Mobility

Access List Configuration

Remote Destination Profile Configuration

Remote Destination Configuration

Mobile Voice Access Directory Number Configuration

H.323 Gateway Configuration for Enterprise Feature Access

Enterprise Feature Access Two-Stage Dialing

Mobility Setting Configuration

Mobility Softkey Configuration

End User Configuration, Cisco Unified Communications Manager Administration Guide

Service Parameters Configuration, Cisco Unified Communications Manager Administration Guide

Licenses for Cisco Unified Mobility, Cisco Unified Communications Manager System Guide

Cisco Unified Mobility Advantage and Cisco Unified Mobile Communicator Integration

Additional Cisco Documentation

Cisco Unified Serviceability Administration Guide

Cisco Unified Communications Manager Security Guide

Applicable Cisco Unified IP Phone User Guides

Applicable Cisco Unified IP Phone Administration Guides

"Cisco Mobility Applications" chapter in Cisco Unified Communications Solution Reference Network Design (SRND) Based on Cisco Unified Communications Manager

"Configuring Cisco Unified Communications Manager for Use With Cisco Unified Mobility Advantage" chapter in the Installation and Administration Guide for Cisco Unified Mobility Advantage