Cisco CallManager Administration Guide, Release 3.0(5)
Understanding Service Parameters
Downloads: This chapterpdf (PDF - 251.0KB) The complete bookPDF (PDF - 4.81MB) | Feedback

Understanding Service Parameters

Table Of Contents

Understanding Service Parameters

Cisco CallManager Service Parameters

Cisco TFTP Service Parameters

Cisco Messaging Interface Service Parameters

Cisco IP Voice Media Streaming Service Parameters

Cisco Database Layer Service Parameters

Cisco Telephony Call Dispatcher Service Parameters


Understanding Service Parameters


The Service Parameters configuration pages for Cisco CallManager (release 3.0 and later) allow you to configure several different services on selected servers. With the Service Parameters application, you can insert, modify, and delete service parameters for those services.


Caution You will never need to add or delete service parameters unless directed by the Cisco Technical Assistance Center (TAC). Some changes to service parameters may cause system failure.

Related Topics

Cisco CallManager Service Parameters

Cisco TFTP Service Parameters

Cisco Messaging Interface Service Parameters

Cisco IP Voice Media Streaming Service Parameters

Cisco Database Layer Service Parameters

Cisco Telephony Call Dispatcher

Cisco CallManager Service Parameters


Caution You will never need to add or delete service parameters unless directed by the Cisco Technical Assistance Center (TAC). Some changes to service parameters may cause system failure.


Note If you must modify trace parameters, we strongly recommend doing so from the Trace Configuration page. Refer to the "Configuring Trace" section for more information.


Table 10-1 contains service parameters configured for Cisco CallManager.

Table 10-1 Cisco CallManager Service Parameters 

ParamName
Values
Description

AbleToEstablishMF

Default: T

Used for certification testing. We recommend you do not change the default value. Valid values are T or F. Sends the SABME at startup instead of waiting for the distance end to do it.

AdHocConferenceMixerType

Default: 2

Specifies the mixer type to be used for AdHoc conferences. If the mixer type is set to Unicast Bridge, when a user presses the Conference button on the phone, the conference supplementary service allocates a Unicast Bridge resource to handle the conference.

AnalogAccessUse729

Default: F

Not supported for Cisco CallManager Release 3.0.

AutoSelectHeldCallFlag

Default: F

Determines whether to automatically select the call on hold when the phone goes off hook if that call was the last signal sent to the phone.

CallDiagnosticsEnabled

Default: F

Determines whether call diagnostic records are generated. Valid values are:

F = not generated

T = generated

CallParkReversionTimeout

Default: 60

The number of seconds to wait before reverting a parked party to the call parker. Valid value is any numeric value.

CallWaitingEnable

Default: T

Enables or disables call waiting for the entire system.

CdrEnabled

Default: F

Determines whether Call Detail Records (CDRs) are generated. Valid values are:

T = Cdrs are generated

F = Cdrs are not generated

CdrLogCallsWithZeroDuration Flag

Default: F

Enables logging of CDR records for calls which were never connected, or which lasted less than one second.

ClearCallsWhenDatalinkGoes Down

Default: T

If the D-channel (datalink) terminates, this setting determines if calls to the phones will be terminated. Valid values are 0 = Do not clear calls when datalink goes down; 1 = Clear calls when datalink goes down.

ConnectDisconnectTimer

Default: 7

Used for debugging purposes only. We strongly recommend you do not change the default value. The maximum time allowed for a response from a connect or disconnect request. Valid value is any numeric value.

DbNoActivityTimeout

Default: 30

The amount of time to wait before closing the file after no database requests have been received. Valid value is any numeric value.

DeviceStatusPollInterval_msec

 

Denotes the time interval between two change of port status messages. You should not modify the default value.

DigitAnalysisTimer

Default: 6

Used for debugging purposes only. We strongly recommend you do not change the default value. The maximum time allowed for a response from a digit analysis requests. Valid value is any numeric value.

DisplayIEDeliveryFlag

Default: F

This flag (when set to T) enables the delivery of the display IE in SETUP and CONNECT messages for the calling and called party name delivery service.

EnableSNMP

Default: T

This parameter enables the collection of SNMP data from the Cisco CallManager.

ForwardMaximumHopCount

Default: 12

Maximum number of attempts to extend a forwarded call. Valid values are:

(Value >=1)

ForwardNoAnswerTimeout

Default: 12

The number of seconds to wait before forwarding on No Answer Condition. Valid values are:

(Value >=1)

GatekeeperControlRegistration Type

Default: F

H.323 Gatekeeper Control Registration Type. We strongly recommend not changing this parameter unless you have a complete understanding of RAS registration.

GatekeeperRefresh

Default: 60 seconds

The number of seconds between gatekeeper refresh messages.

GatewayKeepAliveTimeout

Default: 25

The number of seconds between Gateway Status messages.

GatewayPollTimeout

Default: 10

The number of seconds to wait for a response from a GatewayOpenReq. Valid value is any numeric value.

H225ConnectTime

Default: 0

H.225ConnectTime determines, on an outgoing H.323/H.225 call, whether processing the open logical channel (when audio is transmitted) on the call proceeding, call alerting, or call connecting.

HoldType

Default: F

Original Hold Type requires the user to press the hold button to retrieve a call from hold. The new hold allows the user to press the line button on which the held call is stored to retrieve it.

InterfaceIdentifierPresentFlag

Default: F

This flag only applies to the DMS100 protocol for the digital access gateway in the Channel Identification IE of the SETUP, CALL PROCEEDING, ALERTING, and CONNECT messages. The purpose of this parameter is to interoperate with Nortel PBX when the PBX is configured to use the DMS100 protocol.

IpPrecedence

Default: 0x000000B0

Used by anyone who configures streaming, phones, media applications, etc. We strongly recommend that this parameter never be changed.

L2RetriesN200

Default: 3

The number of retries before declaring the datalink down. Valid value is any numeric value.

LineStateUpdateEnabled

Default: T

Determines whether Line State Server (used by Cisco WebAttendant) can track the active/inactive states of each line/directory number.

LowPriorityQueueThrottling Flag

Default: F

When low priority TCP queue gets too large, the system starts throwing away new call attempts.

LowPriorityQueueThrottling MaxCount

Default: 1000

The maximum number of outstanding low priority stimulus messages in the queue before new call attempts are discarded. Use this value to adjust call response time. Valid value is any numeric value.

MGCPConnectTime

Default: 30 seconds

All the responses sent by Media Gateway are kept in memory for a certain duration. This duration is set to 30 seconds by default. You should not change this value.

MGCPTimeout

Default: 5 seconds

The number of seconds to wait before Cisco CallManager retries its request.

MatchingCgpnWithAttendant Flag

Default: F

On an outbound analog access gateway call, compare if the calling party number matches one of the associated analog access ports. If so, then select that port, otherwise make it so all ports with an attendant number assigned to them are not usable for the life of the current call. This forces selection of another analog access device if another analog access gateway has been configured in RoutePoint/RouteGroup. If another analog access gateway has not been configured, the user hears a fast busy signal.

MaxAdHocConference

Default: 4

Min: 3

Max: maximum size of largest conference bridge in system

Specifies the maximum number of parties that can be added to a Unicast Ad-Hoc conference.

MaxErrorsToReport

Default: 1

The number of errors to report per datalink establishment. Valid value is any numeric value.

MaxMeetMeConferenceUnicast

Default: 10

Min: 3

Max: maximum size of largest conference bridge in system

Specifies the maximum number of participants that can join a Unicast Meet-Me conference.

MaxNumberOfReceivedIFrames BeforeAcking

Default: 0

Receive 5 I-Frames before responding with a receiver ready (RR) for an acknowledgement (ACK). Valid value is any numeric value.

MaxNumberOfStationsIniting

Default: 50

The maximum number of stations trying to initialize without completing all database requests. Under a heavy load, it is possible to overwhelm the system to the point where no calls can be completed. Set these values to restore usability if the system becomes overwhelmed. Decreasing the LowPriorityQueueThrottlingMaxCount provides faster dial tone, but also increases the chances for calls being rejected. Valid value is any numeric value.

MediaExchangeInterfaceCaps Timeout

Default: 8

The number of seconds for a device to send capabilities for a media connection. Valid value is any numeric value.

MediaExchangeTimeout

Default: 5

The number of seconds for a media connection to be made. Valid value is any numeric value.

OutOfBandwidthText

Default: Not Enough Bandwidth

The text to be displayed when the call cannot be placed because there is not enough bandwidth.

OutStandingIFramesK

Default: 7

The maximum number of outstanding I-Frames which are not acknowledged. Valid value is any numeric value.

OverlapReceivingForPriFlag

Default: F

We strongly recommend using the default setting for this parameter.

PreferredG711Millisecond PacketSize

Default: 20

This is the preferred amount of time set for delivering packets. Value for this parameter should never be set below 20, as this will add latency.

PreferredG723Millisecond PacketSize

Default: 30

This is the preferred amount of time set for delivering packets. This parameter should never be set below 20, as this will add latency.

PreferredG729Millisecond PacketSize

Default: 20

This is the preferred amount of time set for delivering packets. This parameter should never be set below 20, as this will add latency.

RASMulticastFlag

Default: F

Allows for multicast registration of RAS. Caution: Do not set this parameter unless you want all RAS devices to register to Cisco CallManager.

RedirectingNumIEDeliveryFlag

Default: F

This flag applies to the SETUP message only on all protocols for the digital access gateway. When the flag is set to True, the RedirectingNumberIE is included in the SETUP message to indicate the first redirecting number and the redirecting reason of the call when Call Forward happens.

SdlListeningPort

Default: 8002

You should not change this value.

SdlMaxUnHandledExceptions

Default: 5

The maximum number of Cisco CallManager exceptions before Cisco CallManager stops running.

SdlTraceDataSize

Default: 100

This parameter is used in the SDL layer. It tells SDL trace processing how many bytes of raw data to dump from each signal that it traces.

SdlTraceFilePath

Default: c:\ProgramFile\Cisco\Trace\SDL\

The absolute path where SDL trace files are located.

SdlTraceFlag

Default: T

The flag to indicate whether SDL traces should be turned on or off. It is set to true by default, meaning that SDL traces are collected by default.

SdlTraceMaxLines

Default: 10000

The maximum number of lines in each file before starting the next file. Valid value is any numeric value.

SdlTraceTotalNumFiles

Default: 100

The maximum number of files before restarting file count and overwriting old files.

SilenceSuppressionSystemWide

Default: T

Determines whether silence suppression is disabled for all devices on a system-wide basis.

SilenceSuppressionWith Gateways

Default: T

Determines whether silence suppression is disabled for all devices on gateways.

StableIn4Flag

Default: F

Used for certification testing. We recommend you do not change the default value.

Station2ndKeepaliveInterval

Default: 60

The Keepalive Interval for backup server.

StationKeepaliveInterval

Default: 30

The number of seconds between keepalive messages sent to Cisco IP Phones (stations). Use any numeric value starting at 30. We recommend you do not use the 0 value.

StatisticsEnabled

Default: T

Determines whether system statistics are generated. Valid values are:

F = not generated

T = generated

StatusEnqPollFlag

Default: F

Sends status enquiries to H.323 devices to check for out of range status. If the device is determined to be out-of-range, the call is terminated. If the device is within range, sending these status enquiries does not disrupt call connection.

StripPoundCalledPartyFlag

Default: T

This flag (when set to T) enables the stripping of # sign digits from the called party IE, of the inbound and outbound Q.931 and H.225 SETUP message.

SuppressOutOfChansEvents

Default: T

Used for debugging purposes only. We strongly recommend you do not change the default value. Determines whether out of channels responses will be sent to event processing.

TimerSendProgress_msec

Default: 3000

Sometimes the other end does not get back fast enough with the Alert, Progress or Connect while in Call_initiated state.

TimerT1Frame_msec

Default: 2000

Valid value is any numeric value in 1/8 second ticks.

TimerT200_msec

Default: 1000

Layer 2 Retransmission time. This is the only timer value which is in 1/40 second ticks, all other values are in 1/8 second ticks. The increased granularity was needed because of certification testing and requirements which were +/-5% on timers. Valid value is any numeric value in 1/40 second ticks.

TimerT203_msec

Default: 10000

Layer 2 Keepalive. Valid value is any numeric value in 1/8 second ticks.

TimerT301_msec

Default: 180000

User-(Call Delivered) ALERTING Received, Network-(Call Received) ALERTING Received. Valid value is any numeric value in 1/8 second ticks.

TimerT302_msec

Default: 10000

Interdigit Timeout. User-(Overlap Receiving) SETUP ACK sent, Network-(Overlap Sending) SETUP ACK sent. Valid value is any numeric value in 1/8 second ticks.

TimerT303_msec

Default: 4000

User-(Call Initiated) SETUP sent, Network-(Call Present) SETUP sent. Valid value is any numeric value in 1/8 second ticks.

TimerT304_msec

Default: 20000

User-(Overlap Sending) SETUP ACK received, Network-(Overlap Receiving) SETUP ACK received. Valid value is any numeric value in 1/8 second ticks.

TimerT305_msec

Default: 30000

User-(Disconnect Request) DISCONNECT sent, Network-(Disconnect Indication) DISCONNECT without progress ind sent. Valid value is any numeric value in 1/8 second ticks.

TimerT306_msec

Default: 30000

Network-(Disconnect Indication) DISCONNECT with progress ind sent. Valid value is any numeric value in 1/8 second ticks.

TimerT307_msec

Default: 180000

Network-(Null) SUSPEND ACK sent. Valid value is any numeric value in 1/8 second ticks.

TimerT308_msec

Default: 4000

User-(Release Request) RELEASE sent, Network-(Release Request) RELEASE sent. Valid value is any numeric value in 1/8 second ticks.

TimerT309_msec

Default: 90000

User/Network-(Any stable State) Datalink lost. Valid value is any numeric value in 1/8 second ticks.

TimerT310_msec

Default: 10000

User-(Outgoing Call Proceed) CALL PROCEED received, Network-(Incoming Call Proceed) CALL PROCEED received. Valid value is any numeric value in 1/8 second ticks.

TimerT313_msec

Default: 4000

User-(Connect Request) CONNECT sent. Valid value is any numeric value in 1/8 second ticks.

TimerT316_msec

Default: 120000

(Restart Request) RESTART sent. Valid value is any numeric value in 1/8 second ticks.

TimerT317_msec

Default: 300000

Valid value is any numeric value in 1/8 second ticks.

TimerT321_msec

Default: 30000

(Any state) D-Channel failure. Valid value is any numeric value in 1/8 second ticks.

TimerT322_msec

Default: 4000

(Any state) STATUS ENQUIRY sent. Valid value is any numeric value in 1/8 second ticks.

TimerTStatusEnqPoll_msec

Default: 10000

(Any state) Timer initially used to send a StatusEnq. This is done to check to see if Symbol H.323 phone is still attached. Valid value is any numeric value in 1/8 second ticks.

TimeToDelayBeforeSendingAn Ack_msec

Default: 0

The time to wait to send a receiver ready (RR) acknowledgement on a given Non poll I-Frame. Valid value is any numeric value in 25 millisecond ticks. 0 = send immediately.

ToneOnCallForward

 

Flag to set tone on call forward on, or off.

ToneOnHoldTime

Default: 10

Min: 5

Max: 99999

The number of seconds to play some type of tone when a call is on hold (minimum of five seconds).

TypeOfCalledNumberForH225Devices

Default: 0

Denotes the type of number (TON) for H225 devices. The default value is 0, which denotes the value sent by call control. A value of 1 indicates an unknown number. A value of 2 denotes a national number and 3, an international number.

Refer to the "Configuring Trace" section for descriptive and configuration information on all trace parameters.

UnknownCallerId

 

The directory number to be displayed. Valid value is any numeric value representing a general number for your system (if you wish to provide caller ID functionality to called parties). Valid value is any valid telephone number.

UnknownCallerIdFlag

Default: T

This parameter is related to the Unknown CallerId field. We strongly recommend using the default setting since this can now be configured using Cisco CallManager Administration.

UnknownCallerIdText

Default: Unknown

The text to be displayed to called parties who have caller ID capability. The first line is 20 characters and the second line is 14 characters. Use a character setup that can be broken into two lines, each of which has the specified number of characters per line.

UserUserIEStatus

Default: F

If the user-to-user information element (UUIE) is passed in the system, enabling UUIE status allows ISDN PRI messages to include them on outbound PRI calls.


Related Topics

Configuring Service Parameters

Cisco TFTP Service Parameters


Caution You will never need to add or delete service parameters unless directed by the Cisco Technical Assistance Center (TAC). Some changes to service parameters may cause system failure.


Note If you must modify trace parameters, we strongly recommend doing so from the Trace Configuration page. Refer to the "Configuring Trace" section for more information.


Table 10-2 contains service parameters configured for Cisco TFTP.

Table 10-2 Cisco TFTP Service Parameters 

ParamName
Values
Description

AnalogTcpPort

Default: 2002

Not used under normal circumstances.

CallManagerIp

Default: 127.0.0.1

Not used under normal circumstances.

CallManagerIpTrack

Default: T

Not used under normal circumstances.

ChangeUDPPort

Default: 3000

Do not change this parameter.

DigitalTcpPort

Default: 2001

Not used under normal circumstances.

FileDelete

Default: T

Flag that enables configuration file deletion. This is necessary to ensure deleted devices do not still get configuration files.

FileLocation

Default: c:\Program Files\Cisco\TFTPpath

String that represents the primary path for building and serving files.

PhoneTcpPort

Default: 2000

Not used under normal circumstances.

ServerIpTrack

Default: T

True means use default local IP address. Do not change this parameter.

TFTPIp

Default: 127.0.0.1

String that represents the IP address of the TFTP server if ServerIpTrack is false.

Refer to the "Configuring Trace" section for descriptive and configuration information on all trace parameters.

UseDb

Default: T

Do not change this parameter.


Related Topics

Configuring Service Parameters

Configuring Cisco TFTP

Configuring Trace

Understanding Trace Configuration

Recommended Trace Settings

Cisco Messaging Interface Service Parameters


Caution You will never need to add or delete service parameters unless directed by the Cisco Technical Assistance Center (TAC). Some changes to service parameters may cause system failure.


Note If you must modify trace parameters, we strongly recommend doing so from the Trace Configuration page. Refer to the "Configuring Trace" section for more information.


Table 10-3 contains service parameters configured for Cisco Messaging Interface (CMI).

Table 10-3 Cisco Messaging Interface (CMI) Service Parameters 

ParamName
Values
Description

BackupCallManagerName

 

This parameter is used to define the names of the Cisco CallManagers that are going to be used for the CMI backup. You can use either the name of a Cisco CallManager or its IP address.

BaudRate

Recommended default: 9600

This parameter defines the RS-232 connection that Cisco CallManager uses to connect to the voice mail system.


Note Many voice mail systems can be configured to use different baud rates, but the one shown here will frequently be correct.


 

CallManagerName

If the default is left blank, CMI will choose the Cisco CallManager, if existing on a local machine.

This parameter is used to define the names of the Cisco CallManagers that are going to be used for the primary CMI. You can use either the name of a Cisco CallManager or its IP address.

DataBits

Default: 7

This parameter defines the RS-232 connection that Cisco CallManager uses to connect to the voice mail system..

DialingPlan

 

This parameter is one of four that are required by CMI to register an intercept for the voice mail system with which CMI is going to work.


Note Small systems without a complex dialing plan usually only need the VoiceMailDn parameter. The remaining parameters, DialingPlan, RouteFilter, VoiceMailPartition will default to empty strings.


 

InputDnSignificantDigits

Default: 10

This parameter is designed to accommodate the differences between voice mailbox numbers and directory numbers (DNs). If a legacy voice mail system has mailbox numbers that are no longer than the DNs on the system, this parameter can be used to strip the most significant digits. The numeric value of this parameter indicates how many digits should be used.

KeepAliveDn

None

This is a string parameter. For most voice mail systems a value of F is acceptable. However, some Octel systems periodically send an invalid DN specifically for the purpose of verifying that the attached Cisco CallManager is functioning properly. In this case, you can turn off ValidateDns if you know the DN that the Octel system will use as a keep-alive. By programming that DN into the KeepAliveDn parameter, you will ensure that the invalid DN message is returned to the voice mail system when needed.

MwiSearchSpace

 

The search space to use when determining the device to be affected by the MWI lamp.

OutputDnFormat

Default: %010s

This parameter is used to format the DNs sent to the voice mail system. Most numbers passed to the voice mail system are formatted using this parameter.

OutputExternalFormat

Default: %010s

This parameter is also used to format the DNs sent to the voice mail system. Most numbers passed to the voice mail system are formatted using this parameter.

Parity

Default: Even

This parameter defines the RS-232 connection that CMI uses to connect to the voice mail system.


Note The parity settings can be None, Even, Odd, Mark, or Space. Settings are usually Even and None, with Mark and Space rarely being used. Just using the first character of the parity name also works.


 

RouteFilter

 

This parameter is one of four that are required by CMI to register an intercept for the voice mail system with which CMI is going to work.


Note Small systems without a complex dialing plan usually only need the VoiceMailDn parameter. The remaining parameters, DialingPlan, RouteFilter, and VoiceMailPartition, will default to empty strings.


 

SerialPort

Default: COM1

This parameter defines the RS-232 connection that CMI uses to connect to the voice mail system.


Note The SerialPort name should be the same name that you see in Device Manager under NT.


 

SsapiKeepAliveInterval

Default: 30

This is a numeric parameter. During normal operations, CMI is attached to a Cisco CallManager. When this is the case, CMI sends a keep-alive message to the Cisco CallManager at the rate (in seconds) specified by this parameter.


Note This parameter should not be changed from the default value unless directed by the Cisco Technical Assistance Center (TAC).


 

StopBits

Default: 1

This parameter defines the RS-232 connection that CMI uses to connect to the voice mail system.

ValidateDns

Default: T

When CMI receives incoming lamp commands from the voice mail system, it normally validates the associated DN against the NumPlan table. This is an attempt to verify that the DN matches an existing DN known to Cisco CallManager. If the DN is not found in NumPlan, an invalid DN message is sent to the voice mailbox.


Note On a system with a lot of traffic to and from the voice mail system, you may choose to skip this validation process by setting the ValidateDns parameter default to F.


 

Refer to the "Configuring Trace" section for descriptive and configuration information on all trace parameters.

VoiceMailDn

 

This parameter represents the voice mail access number.

VoiceMailPartition

 

This parameter is one of four that are required by CMI to register an intercept for the voice mail system with which CMI is going to work. It is the partition in which the voice mail DN resides.


Related Topics

Configuring Service Parameters

Cisco Messaging Interface

Most Commonly Changed CMI Service Parameters

Configuring Trace

Understanding Trace Configuration

Recommended Trace Settings

Cisco IP Voice Media Streaming Service Parameters


Caution You will never need to add or delete service parameters unless directed by the Cisco Technical Assistance Center (TAC). Some changes to service parameters may cause system failure.

Table 10-4 contains service parameters configured for Cisco IP Voice Media Streaming.

Table 10-4 Cisco IP Voice Media Streaming Service Parameters 

ParamName
Values
Description

CFB:OrphanStreamTimeout

Default: 300

Time set (number of seconds) for orphaned CFB calls to stay up when a Cisco CallManager goes down.

ChangeUDPPort

Default: 3000

Do not change this parameter.

MTP:OrphanStreamTimeout

Default: 300

Time set (number of seconds) for orphaned calls or conferences to stay up when a Cisco CallManager goes down.

MTP:RunFlag

Default: F

This flag (when set) enables MTP.

Refer to the "Configuring Trace" section for descriptive and configuration information on all trace parameters.


Related Topics

Configuring Service Parameters

Configuring Media Termination Point

Planning Your MTP Configuration

Avoiding Call Failure/User Alert

Configuring Trace

Cisco Database Layer Service Parameters


Caution You will never need to add or delete service parameters unless directed by the Cisco Technical Assistance Center (TAC). Some changes to service parameters may cause system failure.

Table 10-5 contains service parameters configured for the Database Layer.

Table 10-5 Cisco Database Layer Service Parameters 

ParamName
Values
Description

MaxCdrRecords

 

A service-wide parameter that specifies the maximum number of CDR records to keep. If the CDR tables get too full (the number of records reaches this maximum number) then the oldest records are deleted and a message is sent to the Event log. This check occurs once a day.

Refer to the "Configuring Trace" section for descriptive and configuration information on all trace parameters.


Related Topics

Configuring Service Parameters

Most Commonly Changed CMI Service Parameters

Configuring Trace

Configuring Cisco CallManager, page 12-1

Configuring Cisco CallManager Groups

Cisco Telephony Call Dispatcher Service Parameters


Caution You will never need to add or delete service parameters unless directed by the Cisco Technical Assistance Center (TAC). Some changes to service parameters may cause system failure.

Table 10-6 contains service parameters configured for Cisco Telephony Call Dispatcher.

Table 10-6

ParamName
Values
Description

CCN Line State Port

Default: 3223

This is the port number of the TCP/IP port in Cisco CallManager that is used by the line state server to register and receive line and device information.

LSS Access Password

Default: private

This is the default password used at registration to authenticate line state server.

LSS Listen Port

Default: 3221

This is the TCP port where WA clients register with TcdSrv for Line and Device state information.

TCDServ Listen Port

Default: 4321

This is the TCP port where WA clients register with TcdSrv for Call Control.

Refer to the "Configuring Trace" section for descriptive and configuration information on all trace parameters.


Cisco Telephony Call Dispatcher

Related Topics

Configuring Service Parameters

Configuring Cisco CallManager, page 12-1