The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
Contents
This chapter provides information about Cisco Unity messaging integration which comprises a communications solution that delivers voice messaging and unified messaging in a unified environment.
Cisco Unity comprises a communications solution that delivers voice messaging and unified messaging in a unified environment.
Unified messaging means that users can manage all message types from the same inbox. Cisco Unity works in concert with an Exchange server or (for Cisco Unity 4.0 and later) a Domino server to collect and store all messages-both voice and e-mail-in one message facility. Users can then access voice and e-mail messages on a computer, through a touchtone phone, or over the Internet.
Steps to configure the Cisco Unity or Cisco Unity Connection voice-messaging systems are as follows.
The following lists provide requirements for your phone system and the Cisco Unity server. For specific version information, see the applicable Cisco Unified Communications Manager Integration Guide for Cisco Unity.
A Cisco Unified Communications applications server that consists of Cisco Unified Communications Manager software that is running on Cisco Unified Computing System servers or on a Cisco-approved third-party server configuration
Cisco licenses for all phone lines, IP phones, and other H.323-compliant devices or software (such as Cisco Virtual Phone and Microsoft NetMeeting clients) that will be connected to the network, as well as one license for each Cisco Unity port
IP phones for the Cisco Unified Communications Manager extensions
A LAN connection in each location where you will plug an IP phone into the network
For multiple Cisco Unified Communications Manager clusters, capability for subscribers to dial an extension on another Cisco Unified Communications Manager cluster without having to dial a trunk access code or prefix.
Cisco Unity system that was installed and made ready for the integration as described in the Cisco Unity Installation Guide.
For SCCP integrations (not SIP trunk)-The applicable Cisco Unity-Unified CM TSP installed. For more information on compatible versions of the TSP, see the SCCP Compatibility Matrix: Cisco Unity, Cisco Unity-CM TSP, Cisco Unified CM, and Cisco Unified CM Express.
A license that enables the appropriate number of voice-messaging ports.
The integration uses the LAN to connect Cisco Unity and Cisco Unified Communications Manager. The gateway provides connections to the PSTN. The figure below shows the connections.
Note | The following example applies only if the caller goes through the Cisco Unity Auto-Attendant. Most other calls get routed directly to the correct voice mailbox. For example, callers who call a subscriber and get forwarded to voice-messaging system go directly to the voice mailbox and can record a voice message. Subscribers who call in to check their voice messages from their own phones go directly to their voice mailbox and can listen to voice messages. |
When an external call arrives, the Cisco gateway sends the call over the LAN to the machine on which Cisco Unified Communications Manager is installed.
For Cisco Unified Communications Manager lines that are configured to route calls to Cisco Unity, Cisco Unified Communications Manager routes the call to an available Cisco Unity extension.
Cisco Unity answers the call and plays the opening greeting.
During the opening greeting, the caller enters either the name of a subscriber or an extension; for example, 1234.
Cisco Unity notifies Cisco Unified Communications Manager that it has a call for extension 1234.
At this point, the path of the call depends on whether Cisco Unity is set up to perform supervised transfers or release transfers.
Cisco Unity Connection 1.1 and later support a SIP trunk integration with the Cisco Unified Communications Manager phone system when the Cisco Unified Communications Manager phone system has only phones that are running SIP. See the applicable Cisco Unified Communications Manager SIP Trunk Integration Guide for Cisco Unity Connection for more detailed information. Cisco Unity 4.2 and later also support SIP trunk integrations. See the applicable Cisco Unified Communications Manager SIP Trunk Integration Guide for Cisco Unity for more information. The following list describes a few tips that should be performed from the Cisco Unified Communications Manager Administration side when you are integrating the Cisco Unified Communications Manager phone system with Cisco Unity Connection or Cisco Unity by a SIP trunk:
Create a SIP trunk that points to Cisco Unity and ensure that "Redirecting Number IE Delivery - Outbound" is checked. This instructs Cisco Unified Communications Manager to send the Diversion Header to Cisco Unity, so you access the correct voice mailbox.
Cisco Unified Communications Manager SIP trunk integration applies to MWI. When you configure the SIP trunk security profile for the SIP voice-messaging trunk, check "Accept Unsolicited Notification." This ensures that MWI will operate properly. You must enable "Accept Replaces Header" if you want to support transfers. This allows "REFER w/replaces" to be passed, which is used for Cisco Unity-initiated, supervised transfers.
Assure that your phones support DTMF Relay per RFC-2833. Cisco Unity will support both OOB and RFC-2833.
Define a route pattern (for example, 7555) and point that route pattern to the SIP trunk to Cisco Unity.
Define a voice mail pilot (for example, 7555).
Define a voice mail profile (for example, VM Profile 1) with the voice mail pilot that you defined in the previous step.
Note | Make the voice mail profile that you defined in the preceding step the system default. |
When you configure security for Cisco Unified Communications Manager voice mail ports and Cisco Unity SCCP devices, a TLS connection (handshake) opens for authenticated devices after each device accepts the certificate of the other device; likewise, the system sends SRTP streams between devices; that is, if you configure the devices for encryption.
When the device security mode equals authenticated or encrypted, the Cisco Unity-Unified CM TSP connects to Cisco Unified Communications Manager through the Cisco Unified Communications Manager TLS port. When the security mode equals non-secure, the Cisco Unity TSP connects to Cisco Unified Communications Manager through the Cisco Unified Communications Manager port. Cisco Unity Connection connects to Cisco Unified Communications Manager through the Cisco Unified Communications Manager TLS port.