The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
Contents
This chapter provides information about transcoders. The Media Resource Manager (MRM) provides resource reservation of transcoders. Cisco Unified Communications Manager supports simultaneous registration of both the media termination point (MTP)/trusted relay point (TRP) and transcoder and concurrent MTP/TRP and transcoder functionality within a single call.
A transcoder takes the media stream of one codec and transcodes (converts) it from one compression type to another compression type. For example, it could take a stream from a G.711 codec and transcode (convert) it in real time to a G.729 stream. In addition to codec conversion, a transcoder resource can also provide MTP/TRP functionality to a call.
The Cisco Unified Communications Manager invokes a transcoder on behalf of endpoint devices when the two devices use different voice codecs and would normally not be able to communicate. When inserted into a call, the transcoder converts the data streams between the two incompatible codecs to enable communications between them.The transcoder remains invisible to either the user or the endpoints that are involved in a call.
A transcoder provides a designated number of streaming mechanisms, each of which can transcode data streams between different codecs.
A transcoder takes the media stream of one codec and transcodes (converts) it from one compression type to another compression type. For example, it could take a stream from a G.711 codec and transcode (convert) it in real time to a G.729 stream. In addition to codec conversion, a transcoder resource can also provide MTP/TRP functionality to a call.
Note | The transcoder supports transcoding between G.711 and all codecs, including G.711, when functioning as a transcoder and when providing MTP/TRP functionality. |
The Cisco Unified Communications Manager invokes a transcoder on behalf of endpoint devices when the two devices use different voice codecs and would normally not be able to communicate. When inserted into a call, the transcoder converts the data streams between the two incompatible codecs to enable communications between them. The transcoder remains invisible to either the user or the endpoints that are involved in a call.
A transcoder provides a designated number of streaming mechanisms, each of which can transcode data streams between different codecs.
All Cisco Unified Communications Managers can access transcoders through the Media Resource Manager (MRM). The MRM manages access to transcoders.
The MRM makes use of Cisco Unified Communications Manager media resource groups and media resource group lists. The media resource group list allows transcoders to communicate with other devices in the assigned media resource group, which in turn, provides management of resources within a cluster.
A transcoder control process gets created for each transcoder device that is defined in the database. The MRM keeps track of the transcoder resources and advertises their availability.
Hardware-based transcoder resources also support MTP and/or TRP functionality. In this capacity, when the Cisco Unified Communications Manager determines that an endpoint in a call requires an MTP or TRP, it can allocate a transcoder resource and inserts it into the call, where it acts like an MTP transcoder.
Cisco Unified Communications Manager supports MTP and TRP and transcoding functionality simultaneously. For example, if a call originates from a Cisco Unified IP Phone (located in the G723 region) to NetMeeting (located in the G711 region), one transcoder resource supports MTP and transcoding functionality simultaneously.
If a software MTP resource is not available when it is needed, the call tries to connect without using an MTP resource and MTP/TRP services. If hardware transcoder functionality is required (to convert one codec to another) and a transcoder is not available, the call will fail.
Note | The transcoder supports transcoding between G.711 and all codecs, including G.711, when functioning as a transcoder and when providing MTP/TRP functionality. |
The MTP and Transcoder Resource Throttling Percentage service parameter, which supports the Cisco CallManager service, defines a percentage of the configured number of MTP or transcoder resources and allows Cisco Unified Communications Manager to extend the call to an MTP/transcoder that offers the best chance of successfully connecting the call. When the number of active MTP or transcoder resources is equal to or greater than the percentage that is configured for this parameter, Cisco Unified Communications Manager throttles (stops sending) calls to this MTP/transcoder. Cisco Unified Communications Manager hunts through the Media Resource Group List (MRGL) one time to find a MTP/transcoder that uses matching codecs on both sides of the call. If Cisco Unified Communications Manager cannot find an available MTP/transcoder with matching codecs, Cisco Unified Communications Manager returns to the top of the MRGL to repeat the search, which then includes those MTPs/transcoders that are in a throttled state and that match a smaller subset of capabilities for the call. Cisco Unified Communications Manager extends the call to the MTP/transcoder that is the best match for the call when Cisco Unified Communications Manager determines that a resource may be available; the call fails when the MTP/transcoder cannot allocate a resource for the call. In some cases, Cisco Unified Communications Manager perceives that a resource on a hardware MTP/transcoder is available, but the actual port on the hardware is not available.
For example, if you enter 40 for the Call Count service parameter, which supports the Cisco IP Voice Media Streaming Application service, for a software MTP or transcoder (or for hardware resources, if the maximum sessions is configured at 40, for example), and you set the MTP and Transcoder Resource Throttling Percentage service parameter to 95 percent, Cisco Unified Communications Manager throttles calls to the MTP/transcoder when 38 resources are used on this MTP/transcoder (.95 x 40 = 38). When a new request for an MTP or transcoder arrives, Cisco Unified Communications Manager checks whether the number of resources has dropped to 38 or less, and if so, extends the call to the MTP/transcoder.
For the maximum, minimum, and default values for this service parameter, click the question mark help in the Service Parameter Configuration window in Cisco Unified Communications Manager Administration.
Transcoder types in Cisco Unified Communications Manager Administration are listed in the following table.
Note | The transcoder supports transcoding between G.711 and all codecs, including G.711, when functioning as a transcoder and when providing MTP/TRP functionality. |
This section describes how transcoder devices failover and fallback when the Cisco Unified Communications Manager to which they are registered becomes unreachable. The section also explains conditions that can affect calls that are associated with a transcoder device, such as transcoder 1 reset or restart.
The following items describe the transcoder device recovery methods when the transcoder is registered to a Cisco Unified Communications Manager that goes inactive:
If the primary Cisco Unified Communications Manager fails, the transcoder attempts to register with the next available Cisco Unified Communications Manager in the Cisco Unified Communications Manager Group that is specified for the device pool to which the transcoder belongs.
The transcoder device reregisters with the primary Cisco Unified Communications Manager as soon as Cisco Unified Communications Manager becomes available.
A transcoder device unregisters with a Cisco Unified Communications Manager that becomes unreachable. The calls that were on that Cisco Unified Communications Manager will register with the next Cisco Unified Communications Manager in the list.
If a transcoder attempts to register with a new Cisco Unified Communications Manager and the register acknowledgment is never received, the transcoder registers with the next Cisco Unified Communications Manager.
The transcoder devices will unregister and then disconnect after a hard or soft reset. After the reset completes, the devices reregister with the primary Cisco Unified Communications Manager.
To find out which media resources are associated with a transcoder, choose Dependency Records from the Related Links drop-down list box from the Cisco Unified Communications Manager Administration Transcoder Configuration window. Click Go. The Dependency Records Summary window displays information about media resource groups that are using the transcoder. To find out more information about the media resource group, click the media resource group, and the Dependency Records Details window displays. If the dependency records are not enabled for the system, the dependency records summary window displays a message.
Microsoft Performance Monitor counters for transcoders allow you to monitor the number of transcoders that are currently in use, the number of transcoders that are currently registered with the Cisco Unified Communications Manager but are not currently in use, and the number of times that a transcoder was requested for a call, but no resources were available.
For more information about performance monitor counters, see the Cisco Unified Serviceability Administration Guide.
Cisco Unified Communications Manager writes all errors for the transcoder to the Event Viewer. In Cisco Unified Serviceability, you can set traces for the Cisco IP Voice Media Streaming Application service; to troubleshoot most issues, you must choose the Significant or Detailed option for the service, not the Error option. After you troubleshoot the issue, change the service option back to the Error option.
For more information about the Cisco IP Voice Media Streaming Application service, see the Cisco Unified Serviceability Administration Guide.
Cisco Unified Communications Manager generates registration and connection alarms for transcoder in Cisco Unified Serviceability. For more information on alarms, see the Cisco Unified Serviceability Administration Guide.