buen dia tengo un problema con un switch cisco sf350Cisco SF350 24 PportsSoftware InformationFirmware Version (Active Image): 2.5.8.12Firmware Version (Non-active): 2.5.0.83El problema es que en mi servidor dhcp a cada minuto el switch esta solicitan...
I have a CBS250 that wont power and still under warranty. I called cisco support and they told me I need to finish setting up my profile. However, I cant get access to main site and when I log in, it just kicks me out to main page. can someone help p...
We had some changes recently and have inherited an aging campus infrastructure. Being primarily from service provider background, we are slowly exploring the Campus ecosystem. Does it make sense to use the same devices used in SP for Campus? Core and...
Hello,I am new to networking and have been unable to pin point the source of the issue. We have two CBS 250 devices that have been acting odd lately. 2-4 times a week the management interface would disconnect for about 5-20 mins. I've compared config...
I enabled SNR on a users line. Works fine.Customer does not like that other phones show the option under CME Services URL>My Phone APPS> Single Number Reach, even when the phone line is not programmed to allow SNR. Is the SNR option something that ...
Hello,I need guidance with SPA3102.Line 1 is connected to a SIP trunk and I can make calls (outbound) from the analog telephone (ATA)PSTN Line is also connected to the same SIP trunk, and I need to receive calls (incoming) from the trunk number to th...
Dear all I have a new cbw150ax-s unk access point. I have set a captive portal and test AAA authen with external radius. All work fine but there is no accounting send to my radius server. So I need to access ssh to use terminal and enable radius acco...
We have 2 SG350x-48 switches in a stack. and we need to add another switch. but I know that SG350x-48 is no longer sold. what are my options? these were replaced by the "Cisco Business 350 Series Managed Switches". can one of these switches be a...
I own a CBS350-8XT that is far too noisy. I even purchased a sound meter to obtain a measure and it goes up to 70db where the maximum indicated in the user manual is 41.3db. I would like to open a ticket or something for cisco to fix my unit. How sha...
Hello,I have a C1300, I use it as my IPv4 and IPv6 gateway for internal routing. It has a default gateway to another router for internet access. If I perform an IPv6 speedtest with the c1300 as my gateway for IPv6 then I get around 1Mb, this is stran...
Dear all,I just received a 350x-24. The fan is quite loud, but that isn't a problem as no one sits beside the rack.I just wondered if a noise of 49.2dB average is normal or if it is a indiaction for a hardware or config problem?The noise level was ju...
Router>Router>enRouter#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#Router(config)#Router(config)#Router(config)#crypto key ?decrypt Decrypt a keypair.encrypt Encrypt a keypair.export Export keysgenerate Generate n...
HelloFor a short time now, my LTE connection in the Cisco router has been breaking down repeatedly. This is very annoying because the VPN tunnel used is always gone. Unfortunately I can't do much with the logging messages. these messages are shown af...
Hello,I have an ISP router/modem, along with assignable public IP addresses for use. Leaving default VLAN1 alone (mgmt), I created VLAN10 (192.168.0.0/24) and VLAN20 (172.16.3.0/24) on the CBS350.ISP router "internal" ip 172.16.2.1/24On CBS350 port G...
I have questions in cluster settings. (1) Number of WAP devices per single point setting WAP150:4 Does the setting 'WAP150:4' indicate that a maximum of 4 WAP devices can be connected in a single cluster? (2) Registering an AP in a Created Clu...