PIMG Integration Guide for Cisco Unity Connection Release 7.x
Setting Up a Rolm 9751 Digital PIMG Integration with Cisco Unity Connection
Downloads: This chapterpdf (PDF - 297.0KB) The complete bookPDF (PDF - 9.78MB) | Feedback

Setting Up a Rolm 9751 Digital PIMG Integration with Cisco Unity Connection

Table Of Contents

Setting Up a Rolm 9751 Digital PIMG Integration with Cisco Unity Connection

Task List to Create the Integration with a Rolm 9751 PIMG Phone System

Requirements

Programming the Rolm 9751 PIMG Phone System for Integrating with Cisco Unity Connection

Setting Up the Digital Rolm PIMG Units

Creating a New Integration with the Rolm 9751 Phone System


Setting Up a Rolm 9751 Digital PIMG Integration with Cisco Unity Connection


For detailed instructions for setting up a Rolm 9751 digital PIMG integration with Cisco Unity Connection, see the following sections in this chapter:

Task List to Create the Integration with a Rolm 9751 PIMG Phone System

Requirements

Programming the Rolm 9751 PIMG Phone System for Integrating with Cisco Unity Connection

Setting Up the Digital Rolm PIMG Units

Creating a New Integration with the Rolm 9751 Phone System

Task List to Create the Integration with a Rolm 9751 PIMG Phone System

Before doing the following tasks to integrate Cisco Unity Connection with the Rolm 9751 phone system by using PIMG units (media gateways), confirm that the Cisco Unity Connection server is ready for the integration by completing the applicable tasks in the Cisco Unity Connection Installation Guide.

1. Review the system and equipment requirements to confirm that all phone system and Cisco Unity Connection server requirements have been met. See the "Requirements" section.

2. Plan how the voice messaging ports will be used by Cisco Unity Connection. See Chapter 2, "Planning How the Voice Messaging Ports Will Be Used by Cisco Unity Connection."

3. Program the Rolm 9751 phone system and extensions. See the "Programming the Rolm 9751 PIMG Phone System for Integrating with Cisco Unity Connection" section.

4. Set up the PIMG units. See the "Setting Up the Digital Rolm PIMG Units" section.

5. Create the integration. See the "Creating a New Integration with the Rolm 9751 Phone System" section.

6. Test the integration. See Chapter 14, "Testing the Integration."

7. If this integration is a second or subsequent integration, add the applicable new user templates for the new phone system. See Chapter 15, "Adding New User Template for Multiple Integrations."

Requirements

The Rolm 9751 integration supports configurations of the following components:

Phone System

Rolm 9751 phone system with ROLMphone digital phones.

One of the following software releases:

9005.

9006.

(Software release 9005 only) RolmLink Interface (RLI) card.

(Software release 9006 only) SLMR-type line card.

One or more of the applicable PIMG units. For details, see Chapter 1, "Introduction."

The voice messaging ports in the phone system connected by digital lines to the ports on the PIMG units.

We recommend that you connect the voice messaging ports on the phone system to the ports on the PIMG units in a planned manner to simplify troubleshooting. For example, the first phone system voice messaging port connects to the first port on the first PIMG unit, the second phone system voice messaging port connects to the second port on the first PIMG unit, and so on.

The PIMG units connected to the same LAN or WAN that Cisco Unity Connection is connected to.

If the PIMG units connect to a WAN, the requirements for the WAN network connections are:

For G.729a codec formatting, a minimum of 32.76 Kbps guaranteed bandwidth for each voice messaging port.

For G.711 codec formatting, a minimum of 91.56 Kbps guaranteed bandwidth for each voice messaging port.

No network devices that implement network address translation (NAT).

A maximum 200 ms one-way network latency.

The phone system ready for the integration, as described in the documentation for the phone system.

Cisco Unity Connection Server

Cisco Unity Connection installed and ready for the integration, as described in the Cisco Unity Connection Installation Guide at http://www.cisco.com/en/US/products/ps6509/prod_installation_guides_list.html.

A license that enables the applicable number of voice messaging ports.

Centralized Voice Messaging

Cisco Unity Connection supports centralized voice messaging through the phone system, which supports various inter-phone system networking protocols including proprietary protocols such as Avaya DCS, Nortel MCDN, or Siemens CorNet, and standards-based protocols such as QSIG or DPNSS. Note that centralized voice messaging is a function of the phone system and its inter-phone system networking, not voice mail. Connection will support centralized voice messaging as long as the phone system and its inter-phone system networking are properly configured. For details, see the "Centralized Voice Messaging" section in the "Integrating Cisco Unity Connection with the Phone System" chapter of the Cisco Unity Design Guide Release 7.x at http://www.cisco.com/en/US/docs/voice_ip_comm/connection/7x/design/guide/7xcucdg.html.

Programming the Rolm 9751 PIMG Phone System for Integrating with Cisco Unity Connection

The following programming instructions are provided as an example only. The specific programming for your phone system may vary depending on its configuration.


Caution In programming the phone system, do not send calls to voice messaging ports in Cisco Unity Connection that cannot answer calls (voice messaging ports that are not set to Answer Calls). For example, if a voice messaging port is set only to Send MWI Requests, do not send calls to it.

See the applicable procedure:

To Program the Rolm 9751 Phone System (Software Release 9005)

To Program the Rolm 9751 Phone System (Software Release 9006)

To Program the Rolm 9751 Phone System (Software Release 9005)


Step 1 Use the MO COS_FEATURE command to modify the class of service (COS) for the voice messaging port and the ROLMphone 400 lines so that the following features are set as indicated:

APV (always in privacy)—Yes

NFL (no flash allowed)—No

NOH (no howler)—Yes

DND (do not disturb)—No

Step 2 On an unused Feature Configuration Table, use the CRE BUTTON _400 command to make the following button assignments for the ROLMphone 400. Cancel all remaining button assignments.

Table 10-1 Required Button Assignments 

Button
Setting

9

Enter LINE 1.

10

Enter HOLD.

30

Enter CNCT (connect).

37

Enter MWCTR (message waiting center).

38

Enter XFER (transfer).



Caution All buttons not listed in Table 10-1 must have no assignments. Otherwise the integration will not function correctly.

Step 3 Use the CRE EXT command to create an extension number for each port that will connect to the PIMG units.

For example, the first port can be extension 501, the second port can be extension 502, and so on.

Step 4 Use the CRE RPI <xx><yy><zz> (where <xx> is the shelf number, <yy> is the card slot number, and <zz> is the card channel number) to assign the extension numbers, telephone type (400) and button feature table to the Rolm digital channels. One RPI channel per PIMG port is required.

Step 5 Use the CRE HD_Group 500 command to place all PIMG ports into a hunt group that has the pilot number 500.

Step 6 Continue with the "Setting Up the Digital Rolm PIMG Units" section.


To Program the Rolm 9751 Phone System (Software Release 9006)


Step 1 Use the ADDDPLN command to create a dial plan for the voice messaging port extensions with the following settings.

Table 10-2 ADD Directory Number Table Settings 

Field
Setting

TYPE

Enter DGTS.

DGTS

Enter the extension of the first port that will connect to the PIMG units.

DPLN

Enter 0.

CPS

Leave this field blank.

DAR

Enter STN.

CHECK

Enter N.

ACDP

Leave this field blank.

AC2

Leave this field blank.

CPS2

Leave this field blank.

ACDP2

Leave this field blank.

SKIPDGTS

Leave this field blank.


Step 2 Repeat Step 1 for all remaining ports that will connect to the PIMG units.

Step 3 Use the ADDSTN command to configure the PIMG ports as ROLMphone 400 station sets with the following settings. Accept the default settings for all other fields.

Table 10-3 PIMG Port Settings 

Field
Setting

Station Number/Loc

Enter 2052.

Port Location

Enter 1- 1-115- 2.

Device Type

Enter RP400.

Faceplate#/PrimeKey#

Enter 10/9.


Step 4 Make the following faceplate key assignments.

Table 10-4 Required Faceplate Key Assignments 

Key
Setting

DIGTYPE

Enter RP400.

9

Enter LINE.

30

Enter CNCT.

38

Enter XFER.

40

Enter CALLWT.


Step 5 If you will use a hunt group for the PIMG ports, do the following substeps. Otherwise, continue to Step 6.

a. Use the ADDDPLN command to change the dial plan for the pilot number with the following settings.

Table 10-5 ADD Directory Number Table Settings for the Hunt Group Pilot Number 

Field
Setting

TYPE

Enter DGTS.

DGTS

Enter the pilot number of the hunt group for the PIMG ports.

CPS

Enter 0.

DAR

Enter HUNT.

ACDP

Enter N.


b. Use the ADDHUNT command to add the PIMG port extensions to the hunt group with the following settings.

Table 10-6 ADD Hunt Group Settings for the PIMG Ports 

Field
Setting

TYPE

Enter VCE.

AC

Enter the pilot number of the hunt group for the PIMG ports.

DPLN

Enter the number of the dial plan that you created in Step 1.

STNO

Enter the extension numbers of all the ports that will connect to the PIMG units.

NAME

Leave this field blank.

CQMAX

Enter 0.

FNA

Enter Y.

STYPE

Enter LIN.


Step 6 Use the CHACOS command to configure the class of service (COS) with the following settings for administrators and technicians who must be able to call the PIMG units directly for troubleshooting.

Table 10-7 COS Restriction Table Settings 

Field
Setting

COS

Enter the number of the COS that you are setting up.

AVCE

Enter huntb&huntna&mscap.

ADTE

Leave this field blank.

AFAX

Leave this field blank.

DVCE

Leave this field blank.

DDTE

Leave this field blank.

DFAX

Leave this field blank.


Step 7 Configure forwarding for all subscriber extensions with the following settings.

Table 10-8 Forwarding Settings for Subscriber Extensions 

Field
Setting

VCE Call Forward Dest Type

Enter DN.

Busy Internal

Enter Y.

Busy External

Enter Y.

Do Not Disturb Internal

Enter Y.

Do Not Disturb External

Enter Y.

Ring No Answer Internal

Enter Y.

Ring No Answer External

Enter Y.

All Conditions Internal

Enter Y.

All Conditions External

Enter Y.

Night Option:
VCE Call Forward Dest 1

Enter the pilot number of the hunt group for the PIMG ports.

Night Option:
VCE Call Forward Dest 2

Leave this field blank.

Station Hunt Dest

Leave this field blank.

DNIS Display

Enter Y.

Delayed CFW on Busy

Enter N.

Simplex Voice Call Dest

Leave this field blank.


Step 8 Continue with the "Setting Up the Digital Rolm PIMG Units" section.


Setting Up the Digital Rolm PIMG Units

Do the following procedures to set up the digital Rolm PIMG units that are connected to the Rolm 9751 phone system.

These procedures require that the following tasks have already been completed:

The phone system is connected to the digital Rolm PIMG units by using digital lines.

The PIMG units are ready to be connected to the LAN or WAN.

The PIMG units are connected to a power source.

Fields that are not mentioned in the following procedures must keep their default values. For the default values of all fields, see the documentation for the PIMG units.

To Download the PIMG Firmware Update Files for Digital Rolm PIMG Units


Step 1 On a Windows workstation with a high-speed Internet connection that will have access to the PIMG units, go to the Voice and Unified Communications Downloads page at http://tools.cisco.com/support/downloads/pub/Redirect.x?mdfid=278875240.


Note To access the software download page, you must be logged on to Cisco.com as a registered user.

This procedure describes the steps when using Internet Explorer as your web browser. If you are using a different web browser, the steps may differ.


Step 2 In the tree control on the Downloads page, expand Unified Communications Applications > Voice Mail and Unified Messaging > Cisco Unity, and click Cisco Unity Telephony Integration.

Step 3 On the Log In page, enter your user name and password, then click Log In.

Step 4 On the Select a Release page, under Latest Releases, click the most recent release.

Step 5 In the right column, click the version of the firmware for digital Rolm PIMG units.


Caution Do not use versions 6.0 or 6.0 SU1 of the firmware. Otherwise, MWIs may not function correctly.

Step 6 On the Download Image page, click Download.

Step 7 On the Supporting Document(s) page, click Agree.

Step 8 In the File Download dialog box, click Save.

Step 9 In the Save As dialog box, browse to the Windows workstation that will have access the PIMG units, browse to a directory where you want to save the file, and click Save.

Step 10 In the Download Complete dialog box, click Open. The window for extracting the PIMG firmware update files appears.

Step 11 Click Extract.

Step 12 In the Extract dialog box, browse to the directory where you want the extracted files, and click Extract.

Step 13 Close the window for the extracting application.


Revised May 3, 2010

To Set Up the Digital Rolm PIMG Units (Firmware Version 6.x)


Step 1 On the Windows workstation, add a temporary route to enable access to the PIMG units.

a. On the Windows Start menu, click Run.

b. Enter cmd, and press Enter. The Command Prompt window appears.

c. At the command prompt, enter route add 10.12.13.74 <IP Address of Workstation>, and press Enter.

For example, if the IP address of the workstation is 198.1.3.25, enter "route add 10.12.13.74<space>198.1.3.25" in the Command Prompt window.

d. Close the Command Prompt window.

Step 2 Connect a PIMG unit to the network.

Step 3 In the web browser, go to http://10.12.13.74.

Step 4 To log in, enter the following case-sensitive settings.

Table 10-9 Login Settings 

Field
Setting

Username

Enter admin.

Password

Enter IpodAdmin.


Step 5 Click OK.

Step 6 On the System menu, click Upgrade.

Step 7 On the Upgrade page, click Browse.

Step 8 In the Choose File dialog box, browse to the directory on the Windows workstation that has the extracted PIMG firmware update files.

Step 9 Click Mtl_<xx>.app (where <xx> is multiple digits), and click Open.

Step 10 On the Upgrade page, click Install File.

Step 11 After the file is installed, a message prompting you to restart the PIMG unit appears. Click Cancel.


Caution Do not restart the PIMG unit until you are instructed to do so later in this procedure, even if the file installation fails. Restarting the PIMG unit at this step may prevent the PIMG unit from functioning correctly.

Step 12 Repeat Step 6 through Step 11 for each of the following files (where <xx> is multiple digits):

Mtl_<xx>.fsh

Run<xx>FskEcho.dsp

Mtl<xx>.lca

Step 13 On the Configuration menu, click Import/Export.

Step 14 On the Import/Export page, click Browse.

Step 15 In the Choose File dialog box, browse to the file RLMDNI_Cfg_Rolm.ini.

Step 16 Click RLMDNI_Cfg_Rolm.ini, and click Open.

Step 17 On the Import/Export page, click Import File.

Step 18 After the file is imported, a message prompting you to restart the PIMG unit appears. Click OK.

Step 19 In the web browser, go to http://10.12.13.74.

Step 20 To log in, enter the following case-sensitive settings.

Table 10-10 Login Settings 

Field
Setting

Username

Enter admin.

Password

Enter IpodAdmin.


Step 21 Click OK.

Step 22 If your Cisco Unity Connection system must have an RTP port range of 16384 to 32767, do the following substeps. Otherwise, continue to Step 23.


Caution You must set the RTP port range for the PIMG units if your system uses an RTP port range of 16384 to 32767. Otherwise, Cisco Unity Connection will not be able to answer calls, and callers will hear ringing or silence.

Note The default RTP port range for PIMG units is 49000 to 50000. Some Cisco Unity Connection configurations require a different RTP port range.


a. On the Configuration menu, click Import/Export.

b. On the Import/Export page, under Export Files, click Export All Settings.

c. In the File Download dialog box, click Save.

d. In the Save As dialog box, browse to the Windows workstation that has access to the PIMG units, browse to a directory where you want to save the file, and click Save.

e. In the Download Complete dialog box, click Open. Notepad opens the file Config.ini that you saved.

f. Locate the line with the following parameter:

gwRTPStartPort

g. Change the value of the parameter to 16384 so that the line reads as follows:

gwRTPStartPort = 16384

h. Locate the line with the following parameter:

gwRTPEndPort

i. Change the value of the parameter to 32767 so that the line reads as follows:

gwRTPEndPort = 32767

j. Save the file, and exit Notepad.

k. On the Configuration menu of the PIMG unit, click Import/Export.

l. On the Import/Export page, under Browse for Import File, click Browse.

m. In the Choose File dialog box, browse to the file Config.ini that you saved.

n. Click Config.ini, and click Open.

o. On the Import/Export page, click Import File.

p. When prompted to restart the PIMG unit, click OK.

q. When the PIMG unit has restarted, in the web browser, go to http://10.12.13.74.

r. To log in, enter the following case-sensitive settings.

Table 10-11 Login Settings 

Field
Setting

Username

Enter admin.

Password

Enter IpodAdmin.


s. Click OK.

Step 23 On the System menu, click Password.

Step 24 On the Change Password page, enter the following settings.

Table 10-12 Change Password Page Settings 

Field
Setting

Old Password

Enter IpodAdmin.

(This setting is case sensitive.)

New Password

Enter your new password.

(This setting is case sensitive.)

Confirm Password

Enter your new password.

(This setting is case sensitive.)


Step 25 Click Change.

Step 26 On the Configuration menu, click Routing Table.

Step 27 On the Routing Table page, under Router Configuration, click VoIP Host Groups.

Step 28 Under VoIP Host Groups, enter the following settings for the first VoIP Host Group.

Table 10-13 First VoIP Host Group Settings 

Field
Settings

Name

Accept the default or enter another descriptive name of the VoIP host group.

Load-Balanced

(Cisco Unity Connection without a cluster) Click False.

(Cisco Unity Connection with a cluster configured) Click False.

Fault-Tolerant

(Cisco Unity Connection without a cluster) Click False.

(Cisco Unity Connection with a cluster configured) Click True.


Step 29 For Cisco Unity Connection without a cluster, under Host List, enter the host name or IP address of the Cisco Unity Connection server and the server port in the format <host name or IP address>:5060.

For Cisco Unity Connection with a cluster configured, under Host List, enter the host name or IP address of the subscriber Cisco Unity Connection server (the second Cisco Unity Connection server that you installed) and the server port in the format <host name or IP address>:5060.

Step 30 For Cisco Unity Connection without a cluster, continue to Step 32. For Cisco Unity Connection with a cluster configured, click Add Host.

Step 31 In the second field, enter the host name or IP address of the publisher Cisco Unity Connection server (the first Cisco Unity Connection server that you installed) and the server port in the format <host name or IP address>:5060.


Caution Do not add a third host under Host List or a second host group under VoIP Host Groups. Otherwise, the Cisco Unity Connection cluster may not function correctly.

Step 32 Click Submit.

Step 33 Under Router Configuration, click TDM Trunk Groups.

Step 34 Under TDM Trunk Groups, click Add Trunk Group.

Step 35 Under TDM Trunk Groups, enter the following settings for the first TDM trunk group.

Table 10-14 First TDM Trunk Group Settings (Inbound Calls) 

Field
Settings

Name

Enter Inbound_PBX_Calls or another unique name.

This TDM trunk group will handle all incoming calls from the phone system.

Selection Direction

Click Ascending.

Selection Mode

Click Linear.

Port/Channel Content

Enter the numbers of the PIMG ports that will handle inbound calls. For example, enter "*" for all PIMG ports, or enter "1-6" for the first six PIMG ports.


Step 36 Under TDM Trunk Groups, click Add Trunk Group.

Step 37 Enter the following settings for the second TDM trunk group.

Table 10-15 Second TDM Trunk Group Settings (MWIs) 

Field
Settings

Name

Enter MWIs or another unique name.

This TDM trunk group will handle outbound MWI calls (where applicable).

Selection Direction

Click Ascending.

Selection Mode

Click Cyclic.

Port/Channel Content

Enter the numbers of the PIMG ports that will MWIs. For example, enter "*" for all PIMG ports, or enter "7,8" for the last two PIMG ports.


Step 38 Under TDM Trunk Groups, click Add Trunk Group.

Step 39 Enter the following settings for the third TDM trunk group.

Table 10-16 Third TDM Trunk Group Settings (Outbound Calls) 

Field
Settings

Name

Enter Outbound_PBX_Calls or another unique name.

This TDM trunk group will handle all outbound calls from Cisco Unity Connection.

Selection Direction

Click Descending.

Selection Mode

Click Linear.

Port/Channel Content

Enter * for all channels in all ports.

Enter the numbers of the PIMG ports that will handle outbound (dialout) calls. For example, enter "*" for all PIMG ports, or enter "7,8" for the last two PIMG ports.


Step 40 Click Submit.

Step 41 Under Router Configuration, click Inbound VoIP Rules.

Step 42 Under Inbound VoIP Rules, uncheck the Enabled check box for the default rule.

Step 43 Click Add Rule.

Step 44 Under Inbound VoIP Rules, enter the following settings for the first new inbound VoIP rule.

Table 10-17 First New Inbound VoIP Rule Settings (MWIs) 

Field
Settings

Enable

Check this check box.

Rule Label

Enter MWI_Calls or another name.

This inbound VoIP rule will handle all MWI calls from Cisco Unity Connection.

Request Type

Click Message.

Originating VoIP Host Address

Enter *.


Step 45 Under Inbound VoIP Request Matching, enter the following settings.


Caution The rule that you created in Step 44 must be selected. Otherwise, any changes you make will apply to another rule.

Table 10-18 Inbound VoIP Request Matching Settings 

Field
Settings

Calling Number

Enter *.

Calling Name

Enter *.

Called Number

Enter *.

Called Name

Enter *.

Redirect Number

Enter *.

Redirect Name

Enter *.


Step 46 Under Outbound Routes, enter the following settings.


Caution The rule that you created in Step 44 must be selected. Otherwise, any changes you make will apply to another rule.

Table 10-19 Outbound Routes Settings 

Field
Settings
Device Selection

Outbound Destination

Click TDM.

Trunk Group

Click the name of the TDM trunk group that you created for MWIs in Step 37. For example, click "MWIs.

CPID Manipulation

Calling Number

Enter S.

Calling Name

Enter S.

Called Number

Enter D.

Called Name

Enter D.

Redirect Number

Enter R.

Redirect Name

Enter R.

Select Primary/Alternate Route

Primary

Click Primary.


Step 47 Under Inbound VoIP Rules, click Add Rule.

Step 48 Under Inbound VoIP Rules, enter the following settings for the second new inbound VoIP rule.

Table 10-20 Second New Inbound VoIP Rule Settings (Outbound Calls) 

Field
Settings

Enable

Check this check box.

Rule Label

Enter Outbound_UC_Calls or another name.

This inbound VoIP rule will handle all outbound calls from Cisco Unity Connection.

Request Type

Click Call.

Originating VoIP Host Address

Enter *.


Step 49 Under Inbound VoIP Request Matching, enter the following settings.


Caution The rule that you created in Step 48 must be selected. Otherwise, any changes you make will apply to another rule.

Table 10-21 Inbound VoIP Request Matching Settings 

Field
Settings

Calling Number

Enter *.

Calling Name

Enter *.

Called Number

Enter *.

Called Name

Enter *.

Redirect Number

Enter *.

Redirect Name

Enter *.


Step 50 Under Outbound Routes, enter the following settings.


Caution The rule that you created in Step 48 must be selected. Otherwise, any changes you make will apply to another rule.

Table 10-22 Outbound Routes Settings 

Field
Settings
Device Selection

Outbound Destination

Click TDM.

Trunk Group

Click the name of the TDM trunk group that you created for outbound calls in Step 39. For example, click "Outbound_PBX_Calls."

CPID Manipulation

Calling Number

Enter S.

Calling Name

Enter S.

Called Number

Enter D.

Called Name

Enter D.

Redirect Number

Enter R.

Redirect Name

Enter R.

Select Primary/Alternate Route

Primary

Click Primary.


Step 51 Click Submit.

Step 52 Under Router Configuration, click Inbound TDM Rules.

Step 53 Under Inbound TDM Rules, enter the following settings for the first inbound TDM rule.

Table 10-23 First Inbound TDM Rule Settings 

Field
Settings

Enable

Check this check box.

Rule Label

Enter Inbound_Rule_1 or another name.

This inbound TDM rule will handle all incoming calls from the phone system.

Request Type

Click Call.

Trunk Group

Click the name of the TDM trunk group that you created for incoming calls from the phone system in Step 35. For example, click "Inbound_PBX_Calls."


Step 54 Under Inbound TDM Request Matching, enter the following settings.


Caution The rule that you created in Step 53 must be selected. Otherwise, any changes you make will apply to another rule.

Table 10-24 Inbound TDM Request Matching Settings 

Field
Settings

Calling Number

Enter the applicable matching rule that will be used. For example, enter "*" for all.

Calling Name

Enter the applicable matching rule that will be used. For example, enter "*" for all.

Called Number

Enter the applicable matching rule that will be used. For example, enter "*" for all.

Called Name

Enter the applicable matching rule that will be used. For example, enter "*" for all.

Redirect Number

Enter the applicable matching rule that will be used. For example, enter "*" for all.

Redirect Name

Enter the applicable matching rule that will be used. For example, enter "*" for all.


Step 55 Under Outbound Routes, enter the following settings.


Caution The rule that you created in Step 53 must be selected. Otherwise, any changes you make will apply to another rule.

Table 10-25 Outbound Routes Settings 

Field
Settings
Device Selection

Outbound Destination

Click VoIP.

Host Group

Click the name of the VoIP host group that you created for Cisco Unity Connection in Step 28.

CPID Manipulation

Calling Number

Enter S.

Calling Name

Enter S.

Called Number

Enter D.

Called Name

Enter D.

Redirect Number

Enter R.

Redirect Name

Enter R.

Select Primary/Alternate Route

Primary

Click Primary.


Step 56 If you want to create more Inbound TDM rules, under Inbound TDM Rules, click Add Rule. Otherwise, continue to Step 58.

Step 57 Repeat Step 53 through Step 56 for all remaining inbound TDM rules that you want to create.

Step 58 Click Submit.

Step 59 On the Configuration menu, click TDM > Digital.

Step 60 On the Digital Telephony page, in the Telephony Switch Type field, click the applicable setting for your phone system:

Rolm_9751_SW9005

Rolm_9751_SW9006

Step 61 Click Submit.

Step 62 On the Configuration menu, click TDM > General.

Step 63 On the TDM General Settings page, enter the following settings.

Table 10-26 TDM General Settings Page Settings 

Field
Settings

PCM Coding

Click uLaw.

Minimum Call Party Delay (ms)

Enter 500.

Maximum Call Party Delay (ms)

Enter 2000.

Dial Digit on Time (ms)

Enter 100.

Dial Inter-Digit Time (ms)

Enter 100.

Dial Pause Time (ms)

Enter 2000.

Turn MWI On FAC

Leave this field blank.

Turn MWI Off FAC

Leave this field blank.

Outbound Call Connect Timeout (ms)

Enter 10000.

Wait for Ringback/Connect on Blind Transfer

Click Yes.

Hunt Group Extension

Enter the pilot number of the Cisco Unity Connection voice messaging ports.


Step 64 Click Submit.

Step 65 On the Configuration menu, click TDM > Port Enable.

Step 66 On the TDM Port Enabling page, click No for the ports that you want to disable on the PIMG unit.

Step 67 Confirm that Yes is selected for all other ports on the PIMG unit.

Step 68 Click Submit.

Step 69 On the Configuration menu, click VoIP > General.

Step 70 On the VoIP General Settings page, enter the following settings.

Table 10-27 VoIP General Settings Page Settings 

Field
Setting

User-Agent

Host and Domain Name

Enter the host and domain name of the PIMG unit.

Transport Type

Click UDP.

Call as Domain Name

Click No.

Invite Expiration (sec)

Enter 120.

Server

DNS Server Address

Enter the IP Address of the Domain Name Server that the PIMG unit will use.

Registration Server Address

Leave this field blank.

Registration Server Port

Enter 5060.

Registration Expiration (sec)

Enter 3600.

TCP/UDP

UDP/TCP Transports Enabled

Click Yes.

TCP/UDP Server Port

Enter 5060.

Proxy

Primary Proxy Server Address

Leave this field blank.

Primary Proxy Server Port

Not applicable. Leave the default setting.

Backup Proxy Server Address

Not applicable. Leave the default setting.

Backup Proxy Server Port

Not applicable. Leave the default setting.

Proxy Query Interval

Enter 10.

Timing

T1 Time (ms)

Enter 400.

T2 Time (ms)

Enter 3000.

Monitoring

Monitor Call Connections

Click No.


Step 71 Click Submit.

Step 72 On the Configuration menu, click VoIP > Media.

Step 73 On the VoIP Media Settings page, enter the following settings.

Table 10-28 VoIP Media Settings Page Settings 

Field
Settings

Audio

Audio Compression

Click the preferred codec for audio compression.

RTP Digit Relay Mode

Click RFC2833.

Signaling Digit Relay Mode

Click Off.

Voice Activity Detection

Click Off.

Frame Size

Click the applicable setting:

G.711—20

G.729AB—10


Caution Failure to use the correct setting will result in recorded messages containing nothing but silence.

Frames Per Packet

Click the applicable setting:

G.711—1

G.729AB—2


Caution Failure to use the correct setting will result in recorded messages containing nothing but silence.

Step 74 Click Submit.

Step 75 On the Configuration menu, click VoIP > QOS.

Step 76 On the VoIP QOS Configuration page, enter the following settings.

Table 10-29 VoIP QOS Configurative Page Settings 

Field
Settings

Call Control QOS Byte

Enter 104.

RTP QOS Byte

Enter 184.


Step 77 Click Submit.

Step 78 On the Configuration menu, click IP.

Step 79 On the IP Settings page, enter the following settings.

Table 10-30 IP Settings Page Settings 

Field
Settings

Client IP Address

Enter the new IP address you want to use for the PIMG unit.

(This is the IP address that you enter in Cisco Unity Connection Administration when you create the integration.)

Client Subnet Mask

Enter the new subnet mask, if the subnet mask is different from the default IP address.

Default Network Gateway Address

Enter the IP address of the default network gateway router that the PIMG units will use.

BOOTP Enabled

Click No.


Step 80 Click Submit.

Step 81 On the Configuration menu, click Tone Detection.

Step 82 On the Tone Detection page, under Call Progress Tone - Learn, in the Learn Tone Event field, click Busy and do the following substeps to verify that the tone is correct.

a. From a available phone, call a second phone.

b. Answer the second phone when it rings, and leave both handsets off so that both phones are busy.

c. From a third phone, dial one of the busy phones.

d. Confirm that you hear a busy tone.

e. Hang up the third phone but leave the handsets for the other two phones off.

Step 83 Under Call Progress Tone - Learn, in the Dial String field, enter the extension that you dialed in Step 82c. from the third phone.

Step 84 Click Learn.

Step 85 On the Tone Detection page, under Call Progress Tone - Learn, in the Learn field, click Error and do the following substeps to verify that the tone is correct.

a. From an available phone, dial an extension that does not exist.

b. Confirm that you hear the reorder or error tone.

c. Hang up the phone.

Step 86 Under Call Progress Tone - Learn, in the Dial String field, enter the extension that you dialed in Step 85a.

Step 87 Click Learn.

Step 88 On the Tone Detection page, under Call Progress Tone - Learn, in the Learn field, click Ringback and do the following substeps to verify that the tone is correct.

a. From an available phone, dial an extension that does exist.

b. Confirm that you hear the ringback tone.

c. Hang up the phone.

Step 89 Under Call Progress Tone - Learn, in the Dial String field, enter the extension that you dialed in Step 88a.

Step 90 Click Learn.

Step 91 Click Submit.

Step 92 Hang up the phones that you used in Step 82.

Step 93 On the System menu, click Restart.

Step 94 On the Restart page, click Restart Unit Now.

Step 95 Repeat Step 2 through Step 94 on all remaining PIMG units.


Creating a New Integration with the Rolm 9751 Phone System

Revised August 14, 2009

After ensuring that the Rolm 9751 phone system, the PIMG units, and Cisco Unity Connection are ready for the integration, do the following procedure to set up the integration and to enter the port settings.

To Create an Integration


Step 1 Log on to Cisco Unity Connection Administration.

Step 2 In Cisco Unity Connection Administration, expand Telephony Integrations, then click Phone System.

Step 3 On the Search Phone Systems page, under Display Name, click the name of the default phone system.

Step 4 On the Phone System Basics page, in the Phone System Name field, enter the descriptive name that you want for the phone system.

Step 5 If you want to use this phone system for TRaP connections (when users record and playback through the phone in Cisco Unity Connection web applications), check the Default TRAP Switch check box. If you want to use another phone system for TRaP connections, uncheck this check box.

Step 6 Under Message Waiting Indicator Settings, click Use Same Port for Enabling and Disabling MWIs.

Step 7 Click Save.

Step 8 On the Phone System Basics page, in the Related Links drop-down box, click Add Port Group and click Go.

Step 9 On the New Port Group page, enter the applicable settings and click Save.

Table 10-31 Settings for the New Port Group Page 

Field
Setting

Phone System

Click the name of the phone system that you entered in Step 4.

Create From

Click Port Group Template and click SIP to DMG/PIMG/TIMG in the drop-down box.

Display Name

Enter a descriptive name for the port group. You can accept the default name or enter the name that you want.

SIP Security Profile

Click 5060.

SIP Transport Protocol

Click the SIP transport protocol that Cisco Unity Connection will use.

IP Address or Host Name

Enter the IP address of the PIMG unit that you are integrating with Cisco Unity Connection.

Port

Enter the SIP port of the PIMG unit that Cisco Unity Connection will connect to. We recommend that you use the default setting.


Caution This name must match the setting in the TCP/UDP Server Port field on the Configuration > VoIP > General page of the PIMG unit. Otherwise, the integration will not function correctly.

Step 10 In the Related Links drop-down box, click Add Ports and click Go.

Step 11 On the New Port page, enter the following settings and click Save.

Table 10-32 Settings for the New Ports Page 

Field
Considerations

Enabled

Check this check box.

Number of Ports

Enter 8.

(If you want to use fewer than eight voice messaging ports, enter the number of voice messaging ports that you want to use on this PIMG unit.)

Note For a Cisco Unity Connection cluster, the Cisco Unity Connection server must have the number of voice messaging ports that are set up on the phone system for the PIMG integration so that this Cisco Unity Connection server can handle all voice messaging traffic for the Cisco Unity Connection cluster if one of the servers stops functioning. For example, if the phone system is set up with 16 voice messaging ports, this Cisco Unity Connection server must have 16 voice messaging ports.

Phone System

Click the name of the phone system that you entered in Step 4.

Port Group

Click the name of the port group that you added in Step 9.


Step 12 On the Search Ports page, click the display name of the first voice messaging port that you created for this phone system integration.


Note By default, the display names for the voice messaging ports are composed of the port group display name followed by incrementing numbers.


Step 13 On the Port Basics page, set the voice messaging port settings as applicable. The fields in the following table are the ones that you can change.

Table 10-33 Settings for the Voice Messaging Ports 

Field
Considerations

Enabled

Check this check box to enable the port. The port is enabled during normal operation.

Uncheck this check box to disable the port. When the port is disabled, calls to the port get a ringing tone but are not answered. Typically, the port is disabled only by the installer during testing.

Extension

Enter the extension for the port as assigned on the phone system.

Answer Calls

Check this check box to designate the port for answering calls. These calls can be incoming calls from unidentified callers or from users.

Perform Message Notification

Check this check box to designate the port for notifying users of messages. Assign Perform Message Notification to the least busy ports.

Send MWI Requests

Check this check box to designate the port for turning MWIs on and off. Assign Send MWI Requests to the least busy ports.

Allow TRAP Connections

Check this check box so that users can use the port for recording and playback through the phone in Cisco Unity Connection web applications. Assign Allow TRAP Connections to the least busy ports.

Outgoing Hunt Order

Enter the priority order in which Cisco Unity Connection will use the ports when dialing out (for example, if the Perform Message Notification, Send MWI Requests, or Allow TRAP Connections check box is checked). The highest numbers are used first. However, when multiple ports have the same Outgoing Hunt Order number, Cisco Unity Connection will use the port that has been idle the longest.


Step 14 Click Save.

Step 15 Click Next.

Step 16 Repeat Step 13 through Step 15 for all remaining voice messaging ports for the phone system.

Step 17 In Cisco Unity Connection Administration, expand Telephony Integrations, then click Phone System.

Step 18 On the Search Phone Systems page, under Display Name, click the name of the phone system that you entered in Step 4.

Step 19 Repeat Step 8 through Step 18 for each remaining PIMG unit that will be integrated with Cisco Unity Connection.


Note Each PIMG unit is connected to one port group with the applicable voice messaging ports. For example, a system that uses five PIMG units requires five port groups, one port group for each PIMG unit.


Step 20 If another phone system integration exists, in Cisco Unity Connection Administration, expand Telephony Integrations, then click Trunk. Otherwise, skip to Step 24.

Step 21 On the Search Phone System Trunks page, on the Phone System Trunk menu, click New Phone System Trunk.

Step 22 On the New Phone System Trunk page, enter the following settings for the phone system trunk and click Save.

Table 10-34 Settings for the Phone System Trunk 

Field
Setting

From Phone System

Enter the display name of the phone system that you are creating a trunk for.

To Phone System

Enter the display name of the previously existing phone system that the trunk will connect to.

Trunk Access Code

Enter the extra digits that Cisco Unity Connection must dial to transfer calls through the gateway to extensions on the previously existing phone system.


Step 23 Repeat Step 21 and Step 22 for all remaining phone system trunks that you want to create.

Step 24 In the Related Links drop-down list, click Check Telephony Configuration and click Go to confirm the phone system integration settings.

If the test is not successful, the Task Execution Results displays one or more messages with troubleshooting steps. After correcting the problems, test the connection again.

Step 25 In the Task Execution Results window, click Close.