Contents
- QSIG/DPNSS Phone System with Cisco EGW 2200 Integration Guide for Cisco Unity Connection Release 11.x
- Introduction
- Prerequisites
- Phone System
- Unity Connection Server
- Centralized Voice Messaging
- Integration Tasks
- Task List to Create the Integration
- Integration Description
- Call Information
- Integration Functionality
- Integrations with Multiple Phone Systems
- Planning the Usage of Voice Messaging Ports
- Determining the Number of Voice Messaging Ports
- Voice Messaging Ports to Install
- Voice Messaging Ports to Answer Call
- Voice Messaging Ports to Dial Out
- Considerations for a Unity Connection Cluster
- When Both Unity Connection Servers are Functioning
- When Only One Unity Connection Server is Functioning
- Programming the QSIG/DPNSS Phone System
- Setting Up the Cisco EGW 2200
- Creating a New Integration with the QSIG/DPNSS Phone System
- Testing the Integration
- Setting Up Test Configuration
- Testing an External Call with Release Transfer
- Testing Listening to the Messages
- Setting Up Supervised Transfer on Unity Connection
- Testing Supervised Transfer
- Adding New User Templates for Multiple Integrations
QSIG/DPNSS Phone System with Cisco EGW 2200 Integration Guide for Cisco Unity Connection Release 11.x
Prerequisites
Unity Connection Server
Unity Connection installed and ready for the integration, as described in the “Installing Cisco Unity Connection” chapter of the Install, Upgrade, and Maintenance Guide for Cisco Unity Connection, Release 11.x, available at https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/connection/11x/install_upgrade/guide/b_11xcuciumg.html.
A license that enables the applicable number of voice messaging ports.
A Cisco EGW 2200 ready for the integration as described in the Cisco EGW 2200 documentation.
The Cisco EGW 2200 connected to the LAN and configured for a QSIG/DPNSS backhaul signaling stream from the VoIP gateway.
Centralized Voice Messaging
Unity Connection supports centralized voice messaging through the phone system, which supports various inter-phone system networking protocols including proprietary protocols such as Avaya DCS, Nortel MCDN, or Siemens CorNet, and standards-based protocols such as QSIG or DPNSS. Note that centralized voice messaging is a function of the phone system and its inter-phone system networking, not voicemail. Unity Connection will support centralized voice messaging as long as the phone system and its inter-phone system networking are properly configured. For details, see the “Centralized Voice Messaging” section in the “Integrating Unity Connection with the Phone System” chapter of the Design Guide for Cisco Unity Connection Release 11.x at https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/connection/11x/design/guide/b_11xcucdg.html.
Integration Tasks
Before doing the following tasks to integrate Unity Connection with a QSIG/DPNSS phone system through a Cisco EGW 2200, confirm that Unity Connection is ready for the integration by completing the applicable tasks in the “Installing Cisco Unity Connection” chapter of the Install, Upgrade, and Maintenance Guide for Cisco Unity Connection, Release 11.x, available at https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/connection/11x/install_upgrade/guide/b_11xcuciumg.html.
Task List to Create the Integration
Use the following task list to integrate Unity Connection with the QSIG/DPNSS phone system.
Review the system and equipment requirements to confirm that all phone system and Unity Connection server requirements have been met. See the “Prerequisites section on page 1”.
Plan how the voice messaging ports will be used by Unity Connection. See the “Planning the Usage of Voice Messaging Ports section on page 4”.
Program the QSIG/DPNSS phone system. See the “Programming the QSIG/DPNSS Phone System" section on page 7”.
Set up the Cisco EGW 2200. See the “Setting Up the Cisco EGW 2200 section on page 7”.
Create the integration. See the “Creating a New Integration with the QSIG/DPNSS Phone System section on page 7”.
Test the integration. See the “Testing the Integration section on page 10”.
If this integration is a second or subsequent integration, add the applicable new user templates for the new phone system. See the “Adding New User Templates for Multiple Integrations section on page 13”.
Note
While integrating the Cisco Unity Connection with Cisco Unified Call Manager through a EGW uncheck the Synchronize guest time to host option for Unified Communications product line in Virtualized environment. This enables the Unified Communications to synchronize with their clock to external NTP servers.Integration Description
The QSIG/DPNSS integration uses a Cisco EGW 2200, which translates QSIG or DPNSS call signaling into SIP, a VoIP gateway, and the LAN to connect Unity Connection and a QSIG/DPNSS phone system. Figure 1 shows the required connections.
Call Information
The QSIG/DPNSS integration sends the following information with forwarded calls:
The extension of the calling party (for internal calls) or the phone number of the calling party (if it is an external call and the system uses caller ID)
The reason for the forward (the extension is busy, does not answer, or is set to forward all calls)
Unity Connection uses this information to answer the call appropriately. For example, a call forwarded to Unity Connection is answered with the personal greeting of the user. If the phone system routes the call to Unity Connection without this information, Unity Connection answers with the opening greeting.
Integration Functionality
The QSIG/DPNSS integration with Unity Connection provides the following features:
Easy message access (a user can retrieve messages without entering an ID; Unity Connection identifies a user based on the extension from which the call originated; a password may be required)
Identified user messaging (Unity Connection automatically identifies a user who leaves a message during a forwarded internal call, based on the extension from which the call originated)
Integrations with Multiple Phone Systems
When Unity Connection is installed as Cisco Business Edition—on the same server with Cisco Unified Communications Manager—Unity Connection cannot be integrated with multiple phone systems at one time.
When Unity Connection is not installed as Cisco Business Edition, Unity Connection can be integrated with two or more phone systems at one time. For information on and instructions for integrating Unity Connection with multiple phone systems, see the Multiple Phone System Integration Guide for Unity Connection Release 11.x at https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/connection/11x/integration/guide/multiple_integration/b_cuc11xintmultiple.html.
Planning the Usage of Voice Messaging Ports
Before programming the phone system, you need to plan how the voice messaging ports will be used by Unity Connection. The following considerations will affect the programming for the phone system (for example, setting up the hunt group or call forwarding for the voice messaging ports):
For a Unity Connection cluster, each Unity Connection server must have enough ports to handle all voice messaging traffic in case the other server stops functioning.
The number of voice messaging ports that will only dial out, for example, to send message notification, to set message waiting indicators (MWIs), and to make telephone record and playback (TRAP) connections.
The following table describes the voice messaging port settings in Unity Connection that can be set on Telephony Integrations > Port of Cisco Unity Connection Administration.
Determining the Number of Voice Messaging Ports
The following tasks describe the process for determining the number of voice messaging ports for Unity Connection to install, answer call and dial out calls:
For determining the number of voice messaging ports to Install, see “Voice Messaging Ports to Install section on page 5”.
For determining the number of voice messaging ports to Answer Calls, see “Voice Messaging Ports to Answer Call section on page 5”.
For determining the number of voice messaging ports to Dial Out, see “Voice Messaging Ports to Dial Out section on page 6”.
Voice Messaging Ports to Install
The number of voice messaging ports to install depends on numerous factors, including:
The number of calls Unity Connection will answer when call traffic is at its peak.
The expected length of each message that callers will record and that users will listen to.
The number of MWIs that will be activated when call traffic is at its peak.
The number of TRAP connections needed when call traffic is at its peak. (TRAP connections are used by Unity Connection web applications to play back and record over the phone.)
The number of calls that will use the automated attendant and call handlers when call traffic is at its peak.
It is best to install only the number of voice messaging ports that are needed so that system resources are not allocated to unused ports.
If your system is configured for a Unity Connection cluster, see the “Considerations for a Unity Connection Cluster section on page 6”.
Voice Messaging Ports to Answer Call
The calls that the voice messaging ports answer can be incoming calls from unidentified callers or from users. Assign all of the voice messaging ports to answer calls.
You can set voice messaging ports to both answer calls and to dial out (for example, to send message notifications).
If your system is configured for a Unity Connection cluster, see the “Considerations for a Unity Connection Cluster section on page 6”.
Voice Messaging Ports to Dial Out
Ports that will dial out can do one or more of the following:
Notify users by phone, pager, or email of messages that have arrived.
Make a TRAP connection so that users can use the phone as a recording and playback device in Unity Connection web applications.
If your system is configured for a Unity Connection cluster, see the “Considerations for a Unity Connection Cluster section on page 6”.
Considerations for a Unity Connection Cluster
If your system is configured for a Unity Connection cluster, consider how the voice messaging ports will be used in different scenarios.
When Both Unity Connection Servers are Functioning
A hunt group is configured on the phone system to distribute calls equally to both Unity Connection servers.
The network is configured to send incoming calls first to the subscriber server, then to the publisher server if no answering ports are available on the subscriber server.
Both Unity Connection servers are active and handle voice messaging traffic for the system.
In Cisco Unity Connection Administration, the voice messaging ports are configured so that an equal number of voice messaging ports are assigned to each Unity Connection server. This guide directs you to assign the voice messaging ports to their specific server at the applicable time.
The number of voice messaging ports that are assigned to one Unity Connection server must be sufficient to handle all of the voice messaging traffic for the system (answering calls and dialing out) when the other Unity Connection server stops functioning.
If both Unity Connection servers must be functioning to handle the voice messaging traffic, the system will not have sufficient capacity when one of the servers stops functioning.
If all the voice messaging ports are assigned to one Unity Connection server, the other Unity Connection server will not be able to answer calls or to dial out.
When Only One Unity Connection Server is Functioning
The hunt group on the phone system sends all calls to the functioning Unity Connection server.
The functioning Unity Connection server receives all voice messaging traffic for the system.
The number of voice messaging ports that are assigned to the functioning Unity Connection server must be sufficient to handle all of the voice messaging traffic for the system (answering calls and dialing out).
The functioning Unity Connection server must have voice messaging ports that will answer calls and that can dial out (for example, to set MWIs).
If the functioning Unity Connection server does not have voice messaging ports for answering calls, the system will not be able to answer incoming calls. Similarly, if the functioning Unity Connection server does not have voice messaging ports for dialing out, the system will not be able to dial out (for example, to set MWIs).
Programming the QSIG/DPNSS Phone System
For information on provisioning a QSIG or DPNSS phone system to integrate with Unity Connection, see the Cisco EGW 2200 documentation.
Caution
In programming the phone system, do not send calls to voice messaging ports in Unity Connection that cannot answer calls (voice messaging ports that are not set to Answer Calls). For example, if a voice messaging port is set only to Dialout MWI, do not send calls to it.Setting Up the Cisco EGW 2200
For information on setting up the Cisco EGW 2200, see the Cisco EGW 2200 documentation.
Note
For a Unity Connection cluster, identify the Unity Connection servers with a fully qualified domain name (FQDN), and configure a DNS server to resolve the FQDN to the IP addresses and SIP ports of the Unity Connection server.Creating a New Integration with the QSIG/DPNSS Phone System
ProcedureAfter ensuring that QSIG/DPNSS phone system and Unity Connection are ready for the integration, do the following procedure to set up the integration and to enter the port settings.
Step 1 In Cisco Unity Connection Administration, expand Telephony Integrations, then select Phone System. Step 2 On the Search Phone Systems page, under Display Name, select the name of the default phone system. Step 3 On the Phone System Basics page, in the Phone System Name field, enter the descriptive name that you want for the phone system. Step 4 If you want to use this phone system as the default for TRaP connections so that administrators and users without voicemail boxes can record and playback through the phone in Cisco Unity Connection web applications, check the Default TRAP Switch check box. If you want to use another phone system as the default for TRaP connections, uncheck this check box. Step 5 Select Save. Step 6 On the Phone System Basics page, in the Related Links drop-down box, select Add Port Group and select Go. Step 7 On the New Port Group page, enter the applicable settings and select Save.
Table 2 Settings for the New Port Group Page Select the name of the phone system that you entered in Step 3.
Select Port Group Template and select SIP in the drop-down box.
Enter a descriptive name for the port group. You can accept the default name or enter the name that you want.
Enter the voice messaging pilot number that matches the dial plan configuration of the gateway.
Select the SIP transport protocol that Cisco Unity Connection will use.
Enter the IP address (or host name) of the primary gateway that you are connecting to Unity Connection.
Do not enter a value in this field. IPv6 is not supported for EGW 2200 integrations.
Enter the IP address (or host name) of the primary gateway that you are connecting to Unity Connection.
Enter the IP port of the primary gateway that you are connecting to Unity Connection. We recommend that you use the default setting.
Caution This setting must match the port setting of the gateway. Otherwise the integration will not function correctly. Step 8 On the Port Group Basics page, do the following substeps if there is a secondary gateway. Otherwise, continue to Step 9.
Step 9 On the Port Group Basics page, in the Related Links drop-down box, select Add Ports and select Go. Step 10 On the New Port page, enter the following settings and select Save.
Table 4 Settings for the New Ports Page Enter the number of voice messaging ports that you want to create in this port group.
Note For a Unity Connection cluster, you must enter the total number of voice messaging ports that will be used by all Unity Connection servers. Each port will later be assigned to a specific Unity Connection server. Select the name of the phone system that you entered in Step 3.
Select the name of the port group that you added in Step 7.
Step 11 On the Search Ports page, select the display name of the first voice messaging port that you created for this phone system integration.
Note By default, the display names for the voice messaging ports are composed of the port group display name followed by incrementing numbers. Step 12 On the Port Basics page, set the voice messaging port settings as applicable. The fields in the following table are the ones that you can change.
Table 5 Settings for the Voice Messaging Ports Check this check box to enable the port. The port is enabled during normal operation.
Uncheck this check box to disable the port. When the port is disabled, calls to the port get a ringing tone but are not answered. Typically, the port is disabled only by the installer during testing.
(For Unity Connection clusters only) Select the name of the Unity Connection server that you want to handle this port.
Assign an equal number of answering and dial-out voice messaging ports to the Unity Connection servers so that they equally share the voice messaging traffic.
Check this check box to designate the port for answering calls. These calls can be incoming calls from unidentified callers or from users.
Check this check box to designate the port for notifying users of messages. Assign Perform Message Notification to the least busy ports.
Check this check box to designate the port for turning MWIs on and off. Assign Send MWI Requests to the least busy ports.
Check this check box so that users can use the port for recording and playback through the phone in Unity Connection web applications. Assign Allow TRAP Connections to the least busy ports.
Step 13 Select Save. Step 14 Select Next. Step 15 Repeat Step 12 through Step 14 for all remaining voice messaging ports for the phone system. Step 16 If another phone system integration exists, in Cisco Unity Connection Administration, expand Telephony Integrations, then select Trunk. Otherwise, skip to Step 20. Step 17 On the Search Phone System Trunks page, on the Phone System Trunk menu, select New Phone System Trunk. Step 18 On the New Phone System Trunk page, enter the following settings for the phone system trunk and select Save.
Table 6 Settings for the Phone System Trunk Select the display name of the phone system that you are creating a trunk for.
Select the display name of the previously existing phone system that the trunk will connect to.
Enter the extra digits that Unity Connection must dial to transfer calls through the gateway to extensions on the previously existing phone system.
Step 19 Repeat Step 17 and Step 18 for all remaining phone system trunks that you want to create. Step 20 In the Related Links drop-down list, select Check Telephony Configuration and select Go to confirm the phone system integration settings. If the test is not successful, the Task Execution Results displays one or more messages with troubleshooting steps. After correcting the problems, test the Unity Connection again.
Step 21 In the Task Execution Results window, select Close.
Testing the Integration
To test whether Unity Connection and the phone system are integrated correctly, do the following procedures in the order listed.
If any of the steps indicate a failure, see the following documentation as applicable:
Troubleshooting Guide for Cisco Unity Connection Release 11.x, available at https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/connection/11x/troubleshooting/guide/b_11xcuctsg.html.
Setting Up Test Configuration
Procedure
Step 1 Set up two test extensions (Phone 1 and Phone 2) on the same phone system that Unity Connection is connected to. Step 2 Set Phone 1 to forward calls to the Unity Connection pilot number when calls are not answered.
Caution The phone system must forward calls to the Unity Connection pilot number in no fewer than four rings. Otherwise, the test may fail. Step 3 In Cisco Unity Connection Administration, expand Users, then select Users. Step 4 On the Search Users page, select the display name of a user to use for testing. The extension for this user must be the extension for Phone 1. Step 5 On the Edit User Basics page, uncheck the Set for Self-enrollment at Next Login check box. Step 6 In the Voice Name field, record a recorded name for the test user. Step 7 Select Save. Step 8 On the Edit menu, select Message Waiting Indicators. Step 9 On the Message Waiting Indicators page, select the message waiting indicator. If no message waiting indication is in the table, select Add New. Step 10 On the Edit Message Waiting Indicator page, enter the following settings. Step 11 Select Save. Step 12 On the Edit menu, select Transfer Rules. Step 13 On the Transfer Rules page, select the active rule. Step 14 On the Edit Transfer Rule page, under Transfer Action, select Extension and enter the extension of Phone 1. Step 15 In the Transfer Type field, select Release to Switch. Step 16 Select Save. Step 17 Minimize the Cisco Unity Connection Administration window. Do not close the Cisco Unity Connection Administration window because you will use it again in a later procedure.
Step 18 Sign in to the Real-Time Monitoring Tool (RTMT). Step 19 On the Unity Connection menu, select Port Monitor. The Port Monitor tool appears in the right pane. Step 20 In the right pane, select Start Polling. The Port Monitor will display which port is handling the calls that you will make.
Testing an External Call with Release Transfer
Procedure
Step 1 From Phone 2, enter the access code necessary to get an outside line, then enter the number outside callers use to dial directly to Unity Connection. Step 2 In the Port Monitor, note which port handles this call. Step 3 When you hear the opening greeting, enter the extension for Phone 1. Hearing the opening greeting means that the port is configured correctly. Step 4 Confirm that Phone 1 rings and that you hear a ringback tone on Phone 2. Hearing a ringback tone means that Unity Connection correctly released the call and transferred it to Phone 1. Step 5 Leaving Phone 1 unanswered, confirm that the state of the port handling the call changes to “Idle.” This state means that release transfer is successful. Step 6 Confirm that, after the number of rings that the phone system is set to wait, the call is forwarded to Unity Connection and that you hear the greeting for the test user. Hearing the greeting means that the phone system forwarded the unanswered call and the call-forward information to Unity Connection, which correctly interpreted the information. Step 7 On the Port Monitor, note which port handles this call. Step 8 Leave a message for the test user and hang up Phone 2. Step 9 In the Port Monitor, confirm that the state of the port handling the call changes to “Idle.” This state means that the port was successfully released when the call ended. Step 10 Confirm that the MWI on Phone 1 is activated. The activated MWI means that the phone system and Unity Connection are successfully integrated for turning on MWIs.
Testing Listening to the Messages
Procedure
Step 1 From Phone 1, enter the internal pilot number for Unity Connection. Step 2 When asked for your password, enter the password for the test user. Hearing the request for your password means that the phone system sent the necessary call information to Unity Connection, which correctly interpreted the information. Step 3 Confirm that you hear the recorded name for the test user (if you did not record a name for the test user, you will hear the extension number for Phone 1). Hearing the recorded name means that Unity Connection correctly identified the user by the extension. Step 4 Listen to the message. Step 5 After listening to the message, delete the message. Step 6 Confirm that the MWI on Phone 1 is deactivated. The deactivated MWI means that the phone system and Unity Connection are successfully integrated for turning off MWIs. Step 7 Hang up Phone 1. Step 8 On the Port Monitor, confirm that the state of the port handling the call changes to “Idle.” This state means that the port was successfully released when the call ended.
Setting Up Supervised Transfer on Unity Connection
Procedure
Step 1 In Cisco Unity Connection Administration, on the Edit Transfer Rule page for the test user, in the Transfer Type field, select Supervise Transfer. Step 2 In the Rings to Wait For field, enter 3. Step 3 Select Save. Step 4 Minimize the Cisco Unity Connection Administration window. Do not close the Cisco Unity Connection Administration window because you will use it again in a later procedure.
Testing Supervised Transfer
Procedure
Step 1 From Phone 2, enter the access code necessary to get an outside line, then enter the number outside callers use to dial directly to Unity Connection. Step 2 On the Port Monitor, note which port handles this call. Step 3 When you hear the opening greeting, enter the extension for Phone 1. Hearing the opening greeting means that the port is configured correctly. Step 4 Confirm that Phone 1 rings and that you do not hear a ringback tone on Phone 2. Instead, you should hear the indication your phone system uses to mean that the call is on hold (for example, music). Step 5 Leaving Phone 1 unanswered, confirm that the state of the port handling the call remains “Busy.” This state and hearing an indication that you are on hold mean that Unity Connection is supervising the transfer. Step 6 Confirm that, after three rings, you hear the greeting for the test user. Hearing the greeting means that Unity Connection successfully recalled the supervised-transfer call. Step 7 During the greeting, hang up Phone 2. Step 8 On the Port Monitor, confirm that the state of the port handling the call changes to “Idle.” This state means that the port was successfully released when the call ended. Step 9 Select Stop Polling. Step 10 Sign out of RTMT.
Adding New User Templates for Multiple Integrations
When you create the first phone system integration, this phone system is automatically selected in the default user template. The users that you add after creating this phone system integration will be assigned to this phone system by default.
However, for each additional phone system integration that you create, you must add the applicable new user templates that will assign users to the new phone system. You must add the new templates before you add new users who will be assigned to the new phone system.
For details on adding new user templates, or on selecting a user template when adding a new user, see the “User Attributes” chapter of the System Administration Guide for Cisco Unity Connection Release 11.x. The guide is available at
https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/connection/11x/administration/guide/b_cucsag.html.
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.
Copyright © 2016, Cisco Systems, Inc. All rights reserved.