Voice Configuration Menu Codes
This section contains a quick-reference list of the voice configuration menu options for the Cisco ATA. For information on using the voice configuration menu codes, see "Configuring the Cisco ATA for MGCP."
This section contains the following tables:
•Cisco ATA Voice Menu Codes—Information Options
•Cisco ATA Voice Menu Codes—Configuration Parameters
•Cisco ATA Voice Menu Codes—Software Upgrade
Note Follow each voice menu code with #.
Note The term Cisco ATA refers to both the Cisco ATA 186 and the Cisco ATA 188, unless otherwise stated.
Table A-1 lists codes to return basic Cisco ATA information.
Table A-1 Cisco ATA Voice Menu Codes—Information Options
|
|
|
Build information |
123123 |
Build date of the Cisco ATA software |
Review IP address |
21 |
Returns IP address of the Cisco ATA |
Review MAC address |
24 |
Returns MAC address of the Cisco ATA |
Review network route IP address |
22 |
Returns IP address of the network route |
Review subnet mask |
23 |
Returns subnet mask of the network route |
Version number |
123 |
Returns version number of the Cisco ATA software |
Table A-2 lists configuration codes. For additional information about these parameters, see ""Parameters and Defaults."
Table A-2 Cisco ATA Voice Menu Codes—Configuration Parameters
|
|
|
Audio mode |
312 |
Allows finer control of the audio component to suit certain user applications |
Caller ID method |
316 |
Specifies the signal format when generating the Caller ID format to use |
CA0orCM0 |
5 |
Primary call agent |
CA1orCM1 |
6 |
Alternate call agent |
Connection mode |
311 |
Controls the connection mode of the call signaling protocol |
Dynamic Host Configuration Protocol (DHCP) |
20 |
Controls whether the Cisco ATA can automatically obtain configuration parameters from a server over the network |
DNS 1 IP |
916 |
IP address of the primary DNS server |
DNS 2 IP |
917 |
IP address of the secondary DNS server |
Domain |
931 |
Determines how the domain name portion of the endpoint identifier is constructed. |
EPID0or SID0 |
46 |
MGCP endpoint ID for line 0 (Phone 1 port) |
EPID1or SID1 |
47 |
MGCP endpoint ID for line 1 (Phone 2 port) |
Static IP address |
1 |
IP address of the Cisco ATA |
LBR codec |
300 |
Low-bit-rate codec selection |
Media port |
202 |
Specifies which base port the Cisco ATA uses to receive RTP media streams. |
MGCPPort |
201 |
The listening port for MGCP messages on the Cisco ATA |
MGCP protocol |
38 |
Selects the signaling protocol |
MGCPVer |
206 |
MGCP version string |
NPrintf address |
81 |
IP address of a host to which all Cisco ATA debug messages are sent |
NumTXFrames |
35 |
Sets the default RTP packet size |
OpFlags |
323 |
Enables operational features |
PrfCodec |
36 |
Specifies the preferred default codec |
RetxIntv |
203 |
First retransmission interval |
RetxLim |
205 |
Maximum number or times the Cisco ATA retransmits commands |
Set password |
7387277 |
Configuration interface password |
Signal timers |
318 |
Timeout values controlling the starting or stopping of a signaling event |
Static network route address |
2 |
Network router address |
Static subnet mask |
10 |
Specifies the subnet mask for the Cisco ATA. |
TFTP URL |
905 |
IP address of the TFTP server when TFTP configuration is used |
UDP ToS bits |
255 |
Determines the precedence and delay of UDP IP packets |
Use TFTP |
305 |
Enables TFTP as configuration method |
VLANSetting |
324 |
Enables VLAN ID and 802.1Q priority for Voice Audio IP packet and Signaling IP packet |
Table A-3 lists codes used in the software upgrade process. For information about these codes, see "Upgrading the Cisco ATA Signaling Image."
Table A-3 Cisco ATA Voice Menu Codes—Software Upgrade
|
|
|
Upgrade software |
100 |
Used in the software process to enter the IP address of the PC |
Upgrade language to English |
101 |
Changes or upgrades the voice prompt language to English when upgrading software |