Guest

Cisco BTS 10200 Softswitch

PacketCable and Event Message Guide

  • Viewing Options

  • PDF (1.1 MB)
  • Feedback
PacketCable and Event Message Provisioning and Operations Guide, Cisco BTS 10200 Softswitch, Release 5.0

Table Of Contents

PacketCable and Event Message Provisioning and Operations Guide, Cisco BTS 10200 Softswitch, Release 5.0

Contents

Technical Overview

Cisco BTS 10200 Softswitch in the PacketCable Network

PacketCable-Based Interfaces

Additional Network Interfaces

Gate Coordination Functions

Security Interface Features

Event Message Feature

Billing Data Options

Description of the Event Message Feature

Event Message Generation Details and Content

Timestamp Support for Event Messages

Event Message Transport

Event Message Storage on the CA

PCMM-Based QoS for Type 1 Clients

SOAP/XML Interface for CMS Subscriber Provisioning

SOAP/XML Interface

System Components

CMS Subscriber Provisioning

Call Features

Prerequisites for CMS Subscriber Provisioning

Limitations On CMS Subscriber Provisioning

Planning

Installation

Provisioning Procedures

Provisioning Basic PacketCable and DQoS Features

Provisioning CMS Parameters

Provisioning the CMS Interfaces to the CMTS and eMTA

Provisioning DQoS Parameters for Codec Negotiation Service

Provisioning TGCP Interfaces to TGWs

Provisioning the Keepalive AUEP and ICMP Ping Options

Provisioning MGCP Command Timeout and QoS Parameters

Provisioning the Aggregation ID Subnet

Provisioning CMTS Discovery Using the Static Subnet Table

Provisioning Subscriber ID Parameters and DQoS Measurement Counter

Provisioning Security Interfaces

Provisioning Parameters for Secured Media

Provisioning Security Interfaces to the MTA

Provisioning Security Interfaces to the CMTS

Provisioning Security Interfaces to the TGW

Provisioning Security Interfaces to the RKS

Provisioning IPsec Security Associations and Ciphersuite Algorithms

Provisioning Event Messages

Provisioning Support for EM Transmission and Storage

Provisioning the System to Generate EMs for Billing

Provisioning Media_Alive Verification for EMs

Provisioning PCMM-Based QoS for Type 1 Clients

Provisioning AuditConnection Parameters

Operations, Billing, and EM Transfer Procedures

PacketCable Billing Data and Formats in Deployments Using CDBs

Reset, Control, and Status Commands

Manual Recovery and Transfer of Stored EMs

Recovering the Billing Files

Sending Billing Files to the RKS via FTP

Comparing Checksums

Content of EMs Sent to the RKS

Viewing Media_Alive Verification for EMs

Measurements

Creating Reports and Displays of Measurements

Measurements for the DQoS Feature on COPS Interface

Measurements for the EM Feature

Events and Alarms

Events and Alarms Specific to PacketCable-Based Network Elements and PCMM Features

Events and Alarms for the EM Feature

Events and Alarms for the Security Interface Feature

EM Generation Details and Content

EM Generation Details

EM Content

References

Industry Standards


PacketCable and Event Message Provisioning and Operations Guide, Cisco BTS 10200 Softswitch, Release 5.0


Revised: May 2010, OL-12264-08

This document describes how the Cisco BTS 10200 Softswitch implements PacketCable-based interfaces and functions. It also provides provisioning and operating information for PacketCable features and event messages (EMs). It is intended for use by service provider management, system administration, and engineering personnel who are responsible for designing, installing, provisioning, and maintaining networks that use the Cisco BTS 10200 Softswitch system in a PacketCable-based network.

Feature History

Release
Modification

Release 5.0

Version OL-12264-08:

Updated the "Event Message Transport" section.

Release 5.0

Version OL-12264-07:

Updated the Reset, Control, and Status Commands section.

Release 5.0

Version OL-12264-06:

Release 5.0 MR1 and Release 5.0 MR2— The CMTS Discovery Using the Static Subnet Table feature was implemented in Release 5.0 MR1 of the BTS 10200. Release 5.0 MR2 added enhancements to the CMTS Discovery Using the Static Subnet Table feature.

Release 5.0—The Aggregation ID Subnet feature enables a service provider to use the Subnet table to statically configure all subnets handled by every Cable Modem Termination System (CMTS). The Cisco BTS 10200 Softswitch uses the IP address of the embedded Multimedia Terminal Adapter (eMTA) and Subnet table to determine the CMTS handling of a particular eMTA. An eMTA is a residential gateway. A CMTS is an aggregation device for multiple eMTAs.

Release 5.0

Version OL-12264-05:

Release 5.0—The dqos-supp field is moved from the aggr table to the aggr-profile table. For DQoS to take effect, the aggr entry must be provisioned with an aggr-profile-id, and the aggr-profile entry must have dqos-supp=Y. See Provisioning the CMS Interfaces to the CMTS and eMTA.

Release 5.0, Maintenance Release 1—The QoS entry must have client-type=DQoS for DQoS features to be applied. See Provisioning DQoS Parameters for Codec Negotiation Service and Provisioning TGCP Interfaces to TGWs.

Release 5.0—Added details regarding parameter BEST_EFFORT_ON_QOS_FAIL in ca-config table. See the status commands in the "Reset, Control, and Status Commands" section.

Version OL-12264-04:

Additional information was added for the reset command. See Reset, Control, and Status Commands.


Release
Modification

Release 5.0

Version OL-12264-03:

PCMM provisioning steps were corrected, including the requirement to change the call-agent-profile parameter pcmm-supp to Y. See Provisioning PCMM-Based QoS for Type 1 Clients.

Version OL-12264-02:

The EM attributes, calling party NP source and called party NP source, were added, These are in addition to the following attributes that were included in version OL-12264-01 of this document: jurisdiction information parameter (JIP), account code, authorization code, ported-in calling number, ported-in called number, and billing type (flat rate or measured rate). See EM Content.

The EM billing specification reference was changed from PKT-SP-EM-I07-030815 to PKT-SP-EM-I10-040721 (Industry Standards, and throughout the document). The Cisco BTS 10200 Softswitch complies with the RKS EM billing interface requirements of PKT-SP-EM-I10-040721.

The reference for EM billing file naming was changed from PKT-SP-EM-I07-030815 to EM-N-04.0186-3 (Industry Standards, and throughout the document).

References to PKT-SP-EM1.5-I02-050812 were changed to PKT-SP-EM-I10-040721.

Version OL-12264-01:

This document includes all of the information contained in the Release 4.5.x version, along with information for all Release 5.0 features. New information for Release 5.0 is summarized in the list below.

The "Measurements" section was updated with a link to the measurements information in the Cisco BTS 10200 Softswitch Operations and Maintenance Guide.

The "Events and Alarms" section was updated with a link to the measurements information in the Cisco BTS 10200 Softswitch Troubleshooting Guide.

The following EM attributes were added: jurisdiction information parameter (JIP), account code, authorization code, ported-in calling number, ported-in called number, billing type (flat rate or measured rate).

Information was added regarding the SOAP/XML interface for CMS subscriber provisioning.

Information was added regarding the PCMM-based QoS feature, which provides QoS for type 1 client IP-based endpoints managed by the Cisco BTS 10200 Softswitch. This feature is applicable to endpoints that use SIP, MGCP, or H.323 signaling protocols.

Additional minor updates were made in the Provisioning and Operations sections as indicated by change bars.


Contents

Technical Overview

Planning

Installation

Provisioning Procedures

Operations, Billing, and EM Transfer Procedures

EM Generation Details and Content

References

Technical Overview

This section provides technical information about the implementation of PacketCable features. It covers the following topics.

Cisco BTS 10200 Softswitch in the PacketCable Network

Security Interface Features

Event Message Feature

PCMM-Based QoS for Type 1 Clients

SOAP/XML Interface for CMS Subscriber Provisioning


Note In this document, embedded multimedia terminal adapter (eMTA) refers to eMTAs using PacketCable Network-based Call Signaling (NCS) protocol.


Cisco BTS 10200 Softswitch in the PacketCable Network

The Cisco BTS 10200 Softswitch is a class-independent network-switching element. In a PacketCable-based network, it functions as both a call management server (CMS) and a media gateway controller (MGC). It provides call control, call routing, and signaling for several types of multimedia terminal adapters (MTAs) and embedded MTAs (eMTAs), cable modem termination systems (CMTSs), and trunking gateways (TGWs) in PacketCable-based networks. It provides interfaces to record keeping servers (RKSs) and key distribution centers (KDCs). The Cisco BTS 10200 Softswitch also communicates with announcement servers, SS7-based signaling gateways, MGCP-based media gateways (MGWs), and Session Initiation Protocol (SIP) networks.

Figure 1 shows a typical network with PacketCable-based network elements and the applicable external interfaces of the Cisco BTS 10200 Softswitch. In the PacketCable-based network, the Cisco BTS 10200 Softswitch performs the functions of both the CMS and MGC. The Cisco BTS 10200 Softswitch also provides provisionable options for customizing the external interfaces.

Figure 1 Example of PacketCable-Based Network Architecture

PacketCable-Based Interfaces

The Cisco BTS 10200 Softswitch supports signaling on specific PacketCable-based interfaces shown in Figure 1. The following list summarizes the supported protocols for each of the links:

CMS to MTA (NCS)—CMS-to-MTA interface for subscriber access

CMS to CMTS (COPS)—CMS-to-CMTS interface for gate management

CMS to RKS (EM over RADIUS)—CMS-to-Record Keeping Server (RKS) interface for EM-based billing functions

MGC to RKS (EM over RADIUS)—MGC-to-RKS interface for EM-based billing functions

CMS to CALEA (EM over RADIUS)—CMS-to-CALEA server (DF) interface (Note: DF = Delivery Function)

MGC to TGW (TGCP)—MGC-to-trunking gateway (TGW) interface for TGW management (which allows calls to be connected between the PacketCable network and the PSTN)

Additional interfaces are defined for the PCMM QoS features in the "PCMM-Based QoS for Type 1 Clients" section.

The SOAP/XML interface for CMS subscriber provisioning is defined in the "SOAP/XML Interface for CMS Subscriber Provisioning" section.

For a description of Cisco BTS 10200 Softswitch support for CALEA, see the Cisco BTS 10200 Softswitch System Description. For provisioning procedures related to CALEA support, see the Cisco BTS 10200 Softswitch Provisioning Guide.


Note For information on compliance with specific paragraphs of PacketCable standards and ECNs, contact your Cisco account team.


Additional Network Interfaces

The following additional interfaces are not part of the PacketCable feature set, but they provide other important functions useful in the service provider network:

Cisco BTS 10200 Softswitch/Signaling Gateway (SIGTRAN)—This interface allows calls to be made between the PacketCable network and the PSTN. The Call Agent (CA) of the Cisco BTS 10200 Softswitch interfaces to an Internet transfer point (ITP) signaling gateway (SG), for example, the Cisco 7500 series router. The ITP SG provides an SS7-based interface to the STP (PSTN).

MGCP Interface—The Cisco BTS 10200 Softswitch communicates with MGCP-based TGWs that provide a bearer path to the PSTN.

SIP Interface—Session Initiation Protocol (SIP) signaling is used for the following two functions:

Communications with another CMS

Access to voice mail

Cisco BTS 10200 Softswitch office applications (SNMPv3 and CORBA over TCP/IP)
This interface provides communication with Operations Support System (OSS) and office applications servers.

Gate Coordination Functions

In the PacketCable environment, the Cisco BTS 10200 Softswitch performs the gate coordination functions of a CMS, including the gate controller (GC). GC signaling is based on the COPS stack. Each CMTS informs the CMS when a gate is successfully opened or closed. Two gate coordination messages are used, GATE-OPEN and GATE-CLOSE. Gate coordination is required to avoid several theft-of-service scenarios, as described in Appendix K of the PacketCable Dynamic Quality-of-Service Specification, PKT-SP-DQOS-I07-030815, August 15, 2003.


Note For information on compliance with specific paragraphs of PacketCable standards and ECNs, contact your Cisco account team.


GATE-OPEN Process

The normal coordination process for GATE-OPEN signaling, illustrated in Figure 2, has four main steps:

1. During call setup, the Cisco BTS 10200 Softswitch requests the MTA to commit bearer-path resources.

2. The MTA sends a commit message to the CMTS to request opening of the gate on the bearer path.

3. The CMTS opens the gate and sends a GATE-OPEN message to the Cisco BTS 10200 Softswitch.

4. The Cisco BTS 10200 Softswitch allows the call.

Figure 2 Gate Coordination Signaling Example (GATE-OPEN)

If the Gate-Open message arrives at the Cisco BTS 10200 Softswitch before it has sent a resource-commit request to the MTA, the Cisco BTS 10200 Softswitch sends a Gate-Delete message to the CMTS with Unexpected Gate-Open included in the reason code.

GATE-CLOSE Process

During a call, if the Cisco BTS 10200 Softswitch receives a GATE-CLOSE message from the CMTS, it allows the call to proceed on a best-effort basis, without a guaranteed level of service. (It tears down the call only when one of the parties in the call goes on-hook.)

Security Interface Features


Note For information on compliance with specific paragraphs of PacketCable standards and ECNs, contact your Cisco account team.


The implementation of PKT-SP-SEC-I09-030728, PacketCable Security Specification, July 28, 2003, provides a security scheme for the voice-over-cable network built on a set of security protocols. These protocols, based on the documents listed below, provide authentication (to help prevent theft of bandwidth, denial-of-service attack, replay, and so forth) and enable message integrity, privacy, and confidentiality.

IETF documents covering IP security (IPsec) architecture:

RFC 2401, Security Architecture for the Internet Protocol, IETF (S. Kent, R. Atkinson), Internet Proposed Standard, November 1998

RFC 2406, IP Encapsulating Security Payload (ESP), IETF (D. Piper), Internet Proposed Standard, November 1998

IETF documents covering key management protocols—Internet Key Exchange (IKE) and Kerberos with extensions:

RFC 2409, The Internet Key Exchange (IKE), IETF (D. Harkins, D. Carrel), Internet Proposed Standard, November 1998

RFC 1510, The Kerberos Network Authentication Service (V5), IETF (J. Kohl, C. Neuman), September 1993, with updates presented in PKT-SP-SEC-I09-030728

The Cisco BTS 10200 Softswitch performs the security functions of a CMS and a MGC in the PacketCable environment. It supports security in accordance with PKT-SP-SEC-I09-030728 for both signaling and media:

Signaling security—For signaling from CMS to eMTA, CMS to CMTS, and MGC to TGW

Media (bearer) security—For signaling between originating eMTA and terminating eMTA, which is facilitated by the CMS during call signaling setup

The system supports IPsec features for encryption and authentication on specific PacketCable-based interfaces (see Figure 1). There are two aspects to the security features, the security protocol itself (IPsec), and the key management (Kerberos or IKE). The following list summarizes the supported security type for each of the links:

CMS to MTA (NCS)—IPsec/Kerberos

CMS to CMTS (COPS)—IPsec/IKE

CMS to RKS (EM over RADIUS)—IPsec/IKE

MGC to RKS (EM over RADIUS)—IPsec/IKE

CMS to CALEA (EM over RADIUS)—IPsec/IKE

MGC to TGW (TGCP)—IPsec/IKE

As shown in Figure 1, there is no interface between the KDC and the Cisco BTS 10200 Softswitch. To ensure secure NCS signaling, a dynamic key exchange is performed. This exchange provides for IPsec security operations between the MTA and the Cisco BTS 10200 Softswitch. (These procedures are described in the CableLabs document PacketCable Security Specification, PKT-SP-SEC-I09-030728, under "Kerberized IPsec" and other sections.)

Manual key provisioning must be used to match data stored in the KDC with data stored in the Cisco BTS 10200 Softswitch (pre-setup).

The MTA must contact the KDC to obtain the credentials to talk to the server, which is in this case the Cisco BTS 10200 Softswitch.


Note For information on compliance with specific paragraphs of PacketCable standards and ECNs, contact your Cisco account team.



Note See the "Installation" section regarding the requirement for setting the IPSEC_ENABLED parameter at the time of Cisco BTS 10200 Softswitch software installation.


Event Message Feature

This section describes Cisco BTS 10200 Softswitch support for the EM feature.

Billing Data Options

The Cisco BTS 10200 Softswitch can provision billing support using either of the following billing data generation methods:

Call detail blocks (CDBs)—This is traditional post-call billing data, which is assembled into call detail records (CDRs) by an external billing mediation system or billing server.

PacketCable event messages (EMs)—This is real-time call data flow, which is transferred to an external Record Keeping Server (RKS) that assembles CDRs from the EMs.

The Cisco BTS 10200 Softswitch should be provisioned to generate either EMs or CDBs, but not both.


Caution We strongly recommend that you provision the Cisco BTS 10200 Softswitch to generate either EMs or CDBs, but not both. Attempting to generate both types of records simultaneously can significantly degrade system performance. See the "Provisioning the System to Generate EMs for Billing" section for provisioning details.

The content of the CDBs is outside the scope of this document. See the Cisco BTS 10200 Softswitch Billing Interface Guide for information about CDBs.

Description of the Event Message Feature

EMs are real-time data records containing information about network usage and activities. (They must not be confused with system event messages that report events and sometimes trigger alarms.) EMs are used in PacketCable networks to collect resource usage data for billing purposes. In the PacketCable architecture, EM generation is based on the half-call model. A single EM can contain complete usage data or it might contain only part of the usage information.

The Record Keeping Server (RKS) is a PacketCable network element that receives EMs from network elements, such as the call management server (CMS), media gateway controller (MGC), and the cable modem termination system (CMTS). The physical Cisco BTS 10200 Softswitch contains both CMS and MGC logical network elements. The EMs generated by both the CMS and MGC are sent to the RKS. The RKS correlates the information in multiple EMs and provides the complete record of service for a call, which is referred to as a CDR.

For information about EM-related operations on the Cisco BTS 10200 Softswitch, see the "Operations, Billing, and EM Transfer Procedures" section.

Figure 3 illustrates the PacketCable network elements that are involved in the EM process.

Figure 3 Event Message Interfaces

The EM related interfaces illustrated here are described as follows:

1. MGC to RKS—EMs generated by MGC (Cisco BTS 10200 Softswitch) are sent to RKS.

2. CMS to RKS—EMs generated by CMS (Cisco BTS 10200 Softswitch) are sent to RKS.

3. CMTS to RKS—EMs generated by CMTS are sent to RKS. The Cisco BTS 10200 Softswitch (MGC/CMS) is not involved.

4. CMS to CMTS—CMS (Cisco BTS 10200 Softswitch) sends the billing correlation ID (BCID) to the CMTS using the DQoS GateSet message.

5. CMS to MGC—An internal exchange of originating/terminating information such as BCID and FEID.

PacketCable EMs can support billing and settlement activities for single-zone architectures. The originating and terminating CMSs exchange unique Billing Correlation IDs (BCIDs) and Financial Entity IDs (FEIDs) for each half of the call. The originating CMS sends a BCID and an FEID in the INVITE message. The Cisco BTS 10200 Softswitch allocates the BCID for calls it originates or terminates. Along with the FEID, the BCID is used across network elements to reference calls. The FEID is provisioned on a system-wide basis (a single setting for the Cisco BTS 10200 Softswitch) as defined in the "Provisioning the System to Generate EMs for Billing" section.

Event Message Generation Details and Content

See the "EM Generation Details and Content" section for information on EM data.

Timestamp Support for Event Messages

The system-generated timestamps for EMs are based on the host operating system (OS) time and time zone. This data is not affected by CLI provisioning. The Solaris OS obtains the time automatically through Network Time Protocol (NTP) services.


Caution You should never attempt to modify the system date or time in a Cisco BTS 10200 Softswitch host machine while system components (CA, FS, EMS, and BDMS) are running. The attempt could cause the system to have serious problems. Allow the Solaris OS to obtain the time automatically through NTP services.

Event Message Transport

Remote Access Dial-In User Service (RADIUS) is a client/server protocol used for Authorization, Authentication, and Accounting (AAA). The RADIUS protocol is an industry standard for remote access AAA defined in a set of Internet Engineering Task Force (IETF) standards: RFC 2865 and RFC 2866.

The RADIUS transport protocol is used between the Cisco BTS 10200 Softswitch (CMS/MGC) and the RKS. The RKS (or mediation device) communicates with the IP port configured in platform.cfg file for event message adapter (EMA) process (responsible for sending RADIUS message to the network) in BTS 10200.


Note You should not have both the signaling and management interfaces available to the billing mediation center (the remote end of the RADIUS link). EM packets can originate on any of the BTS 10200 interfaces. Only those EM packets originating in the management network should be allowed. Ensure that the client side can account for the temporary receipt of packets from the two management interfaces of the BTS 10200.


The system sends EMs to an RKS without waiting for acknowledgment of the previous message. The maximum number of pending ACK messages is 256.

EMs are first sent to the primary RKS. If the specified number of retry attempts fail, the EMs are sent to the secondary RKS. If one RKS is found to be unreachable, then the other RKS is considered for subsequent messages. If both the primary and secondary RKSs become unreachable, the EMs are stored in an error file on the hard disk (as described in the "Event Message Storage on the CA" section) and a timer is started. When the timer expires, newly arriving EMs are sent to the primary RKS.

If EMs are being sent to the primary RKS and the primary RKS goes down, the Cisco BTS 10200 Softswitch sends subsequent EMs to the secondary RKS. When the primary RKS comes back up, the Cisco BTS 10200 Softswitch continues to send EMs to the secondary RKS. (It does not automatically begin sending them to the primary RKS.) Provisioning of timers and retry attempts is described in the "Provisioning Support for EM Transmission and Storage" section.

Event Message Storage on the CA


Note For information on compliance with specific paragraphs of PacketCable standards and ECNs listed in this document, contact your Cisco account team.


EMs are stored in the network element (CA) that generates them until they are transferred to the RKS. After receipt of the EMs is acknowledged by the RKS, they are deleted. The number of EMs generated by the Cisco BTS 10200 Softswitch depends on the number of calls processed. Multiple EMs are generated for each call. Depending on provisioning in the call-agent-profile table and the type of call, EMs can be generated by the CMS or MGC (or both) within the CA. The exact storage requirement varies depending on the rate of EM generation and how long the Cisco BTS 10200 Softswitch is required to keep the records before transferring them to an RKS.

The Cisco BTS 10200 Softswitch generates and stores EMs with the following characteristics:

EMs are generated in real time during a call. EMs contain timestamps with a granularity of 1 millisecond. The time interval between generation and transmission is not specified.

The Cisco BTS 10200 Softswitch synchronizes with the network clock using NTP at least once per hour. The deviation of the clock in the Cisco BTS 10200 Softswitch remains within ±100 milliseconds between NTP synchronizations.

EMs that cannot be successfully transferred to the RKS due to loss of communication are stored in the /opt/BTSem directory on the CA. The system uses the file-naming conventions specified in PacketCable ECN EM-N-04.0186-3 for the stored EMs. The maximum EM file size and the time limit on keeping a file open are provisionable, as described in the "Provisioning Support for EM Transmission and Storage" section. These files are not automatically deleted or transferred out of the CA.


Caution Event messages that cannot be successfully transferred to the RKS due to loss of communication are not automatically deleted or transferred out of the CA. You must transfer these files to the RKS when communication is restored.

The procedure for doing this is provided in the "Manual Recovery and Transfer of Stored EMs" section.

Each time an EM file is placed in local storage, the system checks current disk usage and takes the following actions:

The system generates an alarm if the disk space allocated to EMs fills up to a certain level—
50 percent (minor alarm), 70 percent (major alarm), or 100 percent (critical alarm).

When the critical condition is reached, the system issues a critical alarm, and further EMs are dropped without any additional warning.

When the critical condition is reached, the disk usage is monitored periodically (one time every minute) to check if disk space usage has decreased and EMs can be stored again.

PCMM-Based QoS for Type 1 Clients

This section describes the implementation of the PacketCable Multimedia (PCMM) feature that provides quality of service (QoS) for type 1 clients managed by the Cisco BTS 10200 Softswitch. This feature is applicable to endpoints using SIP, MGCP, or H.323 as the call signaling protocol.


Note The Cisco BTS 10200 Softswitch supports this PCMM-based feature in addition to all of the PacketCable-based features provided in earlier releases. If you would like detailed information on compliance with specific PacketCable specifications, contact your Cisco account team.


Figure 4 provides a sample system context for this feature.

Figure 4 Network Architecture with Policy Server and PCMM Interfaces

As shown in Figure 4, the PCMM implementation requires the Cisco BTS 10200 Softswitch to communicate with a policy server (PS), which is a third party device. For calls originating on, or terminating to a type 1 client, the Cisco BTS 10200 Softswitch acts as an application manager (AM) and sends requests to the PS for admission control through PCMM-based signaling. The PS in turn requests the CMTS to allocate bandwidth and other resources as in the request. After resources are allocated, the results are provided to the AM (via the PS) and the Cisco BTS 10200 Softswitch continues with call signaling to set up the call.

For the CLI provisioning procedure related to PCMM-based functions, see the "Provisioning PCMM-Based QoS for Type 1 Clients" section.

For maintenance commands related to the CMTS and PS, see the "Reset, Control, and Status Commands" section.

SOAP/XML Interface for CMS Subscriber Provisioning

This section describes the implementation of PacketCable CMS subscriber provisioning on the BTS 10200 with a Simple Object Access Protocol/Extensible Markup Language (SOAP/XML) interface.

This initial release supports only the Pkt-p1 interface to the Provisioning Server (PS)/Call Management Server (CMS) and only the PcspService Object, without extensions. It supports a subset of the call feature objects in the ListOfCallFeatures element.

In the Pkt-p1 interface, the Cisco BTS 10200 Softswitch plays the role of CMS. Any third-party PS using SOAP, Version 1.1, can provision the BTS. The requests and responses between the CMS and the PS are encapsulated in SOAP, Version 1.1, messages. A secure transport protocol is provided by Internet Protocol Security (IPSec).

SOAP/XML Interface

Currently, a user can connect to a BTS 10200 Common Object Request Broker Architecture (CORBA) server to access command templates and enter command executions, allowing system-to-system provisioning. The feature described in this document allows the XML commands to be transported by the SOAP transport protocol, rather than CORBA. Users of this feature communicate with a BTS SOAP server, which resides on the BTS 10200 EMS.

The BTS 10200 XML schema is a general purpose schema currently used by the XML/CORBA interface. The XML schema does not change with the incorporation of the SOAP transport protocol.

SOAP/XML Adapter and specifications are documented in the Cisco BTS10200 Softswitch SOAP Adapter Interface Specification Programmer Guide.

System Components

CMS subscriber provisioning involves the interface between the following components:

Provisioning Server (PS)—Provides the interface between the service provider's back office components and the PacketCable elements. The PS consists of a provisioning application that contains provisioning logic and a provisioning SNMP entity that provides access to active components.

Call Management Server (CMS)—Provides call control and signaling-related services for the MTA and CMTS in the PacketCable network. The BTS 10200 is the CMS.

CMS Subscriber Provisioning

CMS subscriber provisioning includes the operations necessary to provide a specified service to a customer and provides two main functions:

CMS Basic POTS Provisioning (BPP)—Provides the CMS with the minimum information necessary for routing of plain old telephone service (POTS) in the PacketCable network. Data consists of a telephone number mapped to its associated MTA's FQDN and NCS endpoint identifier and is used to set up translation tables enabling the CMS to route calls to the appropriate device given a specific telephone number. BPP for a customer is required before the customer can receive any calls.

CMS Call Feature Provisioning (CFP)—Provides call features to a customer.

Call Features

The following call features are supported by the PacketCable CMS subscriber provisioning interface. The name of each feature is listed below in PacketCable terminology, followed by the corresponding BTS 10200 feature in ( ):

Calling Number Delivery (CND)

Calling Name Delivery (CNAM)

Calling Identity Delivery on Call Waiting (CIDCW)

Call Waiting (CW)

Cancel Call Waiting (CCW)

Call Forwarding Variable and Usage-Sensitive Call Forwarding (*72/*73) (CFVBBG)

Automatic Recall (*69) (AR)

Automatic Callback (*66) (AC)

Visual Message Waiting Indicator (VMWI)

Customer Originated Trace (*57) (COT)

Three Way Calling/Usage-Sensitive Three-Way Calling (*71) (TWC)

Remote Activation of Call Forwarding (RACF)

Anonymous Call Rejection (*77/*87) (ACR)

Call Forwarding Busy Line (*68/*40/*88) (CFB)

Call Forwarding Don't Answer (*68/*24/*88) (CFNA)

Call Forwarding Combination (CFU)

Selective Call Forwarding (*63/*83) (SCF)

Selective Call Acceptance (*64/*84) (SCA)

Selective Call Rejection (*60/*80) (SCR)

Distinctive Ringing/Call Waiting (*61/*81) (DRCW)

Speed Calling (*74/*75) (SC1D)

Line Service Restriction (COS)

Do Not Disturb (DND)

Prerequisites for CMS Subscriber Provisioning

The web server and SOAP engine are running

The CMS and the PS reside in the same secure provisioning domain

Limitations On CMS Subscriber Provisioning

The CMS provisioning interface is limited to the exchange of service activation data between the CMS and the provisioning server.

The CMS provisioning interface supports only the existing CMS subscriber provisioning functionality in the BTS 10200.

The scope of the feature is limited to subscriber provisioning in a PacketCable 1.5 network

The system supports only the Pkt-p1 interface to the provisioning server/CMS and only the PcspService Object, without extensions. It supports a subset of the call feature objects in the ListOfCallFeatures element.

Planning

Delivery of the features and functions described in this document requires interoperability with the network elements connected to the Cisco BTS 10200 Softswitch. See the "Component Interoperability" section in the Cisco BTS 10200 Softswitch Release Notes, which lists the specific peripheral platforms, functions, and software loads that have been tested by Cisco for interoperability with the Cisco BTS 10200 Softswitch.


Note The "Component Interoperability" section in the Cisco BTS 10200 Softswitch Release Notes is intended as a guide. Earlier or later releases of platform software might be interoperable, and it might be possible to use other functions on these platforms. The list certifies only that the required interoperation of these platforms, the functions listed, and the protocols listed have been successfully tested with the Cisco BTS 10200 Softswitch.


Installation

Installation of Cisco BTS 10200 Softswitch software follows a standard process. For details, see the Application Installation Procedure in the Cisco BTS 10200 Softswitch documentation set. Of the three main PacketCable feature areas (DQoS, EM, and security), two of them (DQoS and EM) are always installed, and do not require the setting of any special flags during software installation. However, the third area (security) is not installed unless a special flag (IPSEC_ENABLED) is set in the opticall.cfg file during software installation.


Caution We strongly recommend that you contact Cisco TAC if you believe that you might need to reinstall Cisco BTS 10200 Softswitch software in order to change the value of IPSEC_ENABLED.

Provisioning Procedures

This section explains how to perform the following procedures:

Provisioning Basic PacketCable and DQoS Features

Provisioning Security Interfaces

Provisioning Event Messages

Provisioning PCMM-Based QoS for Type 1 Clients

Provisioning AuditConnection Parameters

These tasks include examples of CLI commands that illustrate how to provision the specific feature. Most of these tables have additional tokens that are not included in the examples. For a complete list of all CLI tables, tokens, descriptions, valid ranges, and default values, see the Cisco BTS 10200 Softswitch Command Line Interface Reference Guide.


Note The command sequences shown in this section provide guidance on how to provision a new system. Therefore, in most cases the commands are "add" commands. If you are modifying previously provisioned GWs, TGs, and so forth, use the "change" commands.


Provisioning Basic PacketCable and DQoS Features

This section describes how to provision the Cisco BTS 10200 Softswitch interfaces to connect to other PacketCable-based NEs and how to select dynamic quality of service (DQoS) options. It includes the following tasks:

Provisioning CMS Parameters

Provisioning the CMS Interfaces to the CMTS and eMTA

Provisioning DQoS Parameters for Codec Negotiation Service

Provisioning TGCP Interfaces to TGWs

Provisioning the Keepalive AUEP and ICMP Ping Options

Provisioning MGCP Command Timeout and QoS Parameters

Provisioning the Aggregation ID Subnet

Provisioning CMS Parameters

This section describes how to provision DQoS functionality for the CMS logical entity on the Cisco BTS 10200 Softswitch (Call Agent).

SUMMARY STEPS

1. Enable DQoS support—change call-agent-profile.

2. Set CMS timers in Call Agent Configuration (ca-config) table (optional, if using other than the default values)—change ca-config.

3. Set the local ringback flag, differential service code point (DSCP)/type of service (TOS) parameter, and maximum MGCP datagram sizes in the ca-config table (optional, if using other than the default values)—change ca-config.


Note The token values shown in this section are examples.


DETAILED STEPS

 
Command Examples
Purpose

Step 1 

change call-agent-profile id=CA146; dqos-supp=y; description=BostonCA33


Enables DQoS support.

The command is shown as change call-agent-profile. However, if the system responds that the call-agent-profile ID does not exist, reenter the command as add call-agent-profile.

Step 2 

change ca-config type=DQOS-T1-TIMER;
datatype=INTEGER; value=250;


change ca-config type=DQOS-DS-SLACK-TERM;
datatype=INTEGER; value=30000;


change ca-config type=DQOS-GATE-TIMER;
datatype=INTEGER; value=3;

Specifies values other than the defaults for individual CMS timers in the ca-config table. The applicable timers are DQOS-T1-TIMER, DQOS-T5-TIMER, DQOS-T7-TIMER, DQOS-T8-TIMER, DQOS-DS-SLACK-TERM, DQOS-US-
SLACK-TERM, and DQOS-GATE-TIMER.

The default values for these timers might be adequate for your specific case. In each case, you can use the show command to find out how the parameter is currently set. See the Cisco BTS 10200 Softswitch Command Line Interface Reference Guide for parameter definitions and valid ranges.

The command is shown as change ca-config. However, if the system responds that the parameter does not exist, reenter the command as add ca-config.

Step 3 

change ca-config type=LOCAL-RINGBACK;
datatype=BOOLEAN; value=N;


change ca-config type=COPS-DSCP-TOS;
datatype=INTEGER; value=96;


change ca-config type=MAX-MGCP-DATAGRAM;
datatype=INTEGER; value=3900;


Specifies additional ca-config parameters that can be set to values other than the defaults.

The default values for these parameters might be adequate for your specific case. In each case, you can use the show command to find out how the parameter is currently set. See the Cisco BTS 10200 Softswitch Command Line Interface Reference Guide for parameter definitions and valid ranges.


Caution We do not recommend that you change the DSCP value unless necessary, and recommend that you contact Cisco TAC regarding any plans to change it.

The MAX-MGCP-DATAGRAM parameter specifies the maximum size of an MGCP message datagram (which can include one or more piggybacked messages) that the Cisco BTS 10200 Softswitch can decode before discarding the rest of the message part. The default value of 4000 bytes is adequate for most applications, and Cisco does not recommend that you change this value unless you are deploying MGCP-based media gateways or MTAs that require larger datagram sizes.

The command is shown as change ca-config. However, if the system responds that the parameter does not exist, reenter the command as add ca-config.

Provisioning the CMS Interfaces to the CMTS and eMTA

This section describes how to provision the interfaces to the CMTS and eMTA nodes. Specific tables are provisioned for each of these interfaces:

CMTS—The Aggregation Profile (aggr-profile) and Aggregation (aggr) tables define the parameters for the connected CMTS devices. These parameters are used by the COPS adapter to establish and terminate TCP connections to the CMTS.

MTA (or eMTA)—The Cisco BTS 10200 Softswitch uses the Media Gateway Profile (mgw-profile), mgw, and termination tables to establish and terminate connections to the eMTAs. The supported MGCP variant is NCS. The following tables are provisioned for this interface:

The mgw-profile table provides templates for defining each type of eMTA by hardware vendor. It identifies the specifications and settings necessary for communications between the Cisco BTS 10200 Softswitch (which functions as the CMS) and each type of eMTA. An mgw-profile ID must be created in this table before entries can be added to the mgw table. Several tokens have values that can be overwritten after the Cisco BTS 10200 Softswitch (CMS) queries the eMTA for supported capabilities. If the eMTA returns a value different from the value originally provisioned in the Cisco BTS 10200 Softswitch, the returned value automatically replaces the originally provisioned value.

The mgw table holds information about each eMTA managed by the Cisco BTS 10200 Softswitch (CMS). The eMTA can be uniquely addressed by domain name, an IP address, or the TSAP address.

The termination table holds information about each endpoint in eMTAs managed by the CMS. Termination events and signals are grouped into packages, which are groupings of events and signals supported by a particular type of endpoint, such as an eMTA endpoint. One or more packages can exist for a given endpoint-type.

SUMMARY STEPS

1. Create the CMTS and enable DQoS support—add aggr-profile and add aggr.

2. Create the profile for eMTA and specify the appropriate parameters—add mgw-profile.

3. Verify that all parameters affecting eMTAs are properly populated, either by default or by the operator—show mgw-profile.

4. Modify parameters affecting eMTAs, if necessary—change mgw-profile.

5. Create the specific eMTA, associate it with the applicable CMTS, and set appropriate parameters—add mgw.

6. Add the line termination for an eMTA—add termination.

7. Bring the eMTA into service—control mgw.

8. Equip the termination and place it in service— equip subscriber-termination and control subscriber-termination.


Note The token values shown in this section are examples.


DETAILED STEPS

 
Command Examples
Purpose

Step 1 

add aggr-profile id=aggrprofile001; 
dqos-supp=y;

add aggr id=cmts777;
tsap-addr=ADDRESS123.cisco.com; aggr-profile-id=aggrprofile001

Creates the CMTS (aggregation device) and enables DQoS support.

The TSAP-ADDR can be a DNS or IP address. If you enter a DNS address, it must be a fully qualified domain name (FQDN).


Caution DQoS is disabled (DQOS-SUPP=N) by default. Set this value to Y to enable DQoS.

Step 2 

add mgw-profile id=mgwprofile777; mgcp-version=MGCP-1-0; mgcp-variant=NCS-1-0; mgcp-default-pkg=LINE; mgcp-conn-id-at-gw-supp=n;

Creates the mgw-profile for this type of eMTA, and specifies values for the optional parameters.

The default values for these parameters might be adequate for your specific case. In each case, you can use the show command to find out how the parameter is currently set. See the Cisco BTS 10200 Softswitch Command Line Interface Reference Guide for parameter definitions and valid ranges.

Step 3 

show mgw-profile id=mgwprofile777;


Verify that the following values are present:

vendor=Cisco [or applicable vendor name]

mgcp-version=MGCP-1-0

mgcp-variant=NCS-1-0

mgcp-default-pkg=LINE

codec-neg-supp=y

pc-mptime-supp=y

mgcp-xdlcx-supp=n

domain-name-caching-supp=y

mgcp-conn-id-at-gw-supp=y

Shows the provisioned values for the parameters in the mgw-profile table.

Step 4 

change mgw-profile id=mgwprofile777; mgcp-version=MGCP-1-0; mgcp-variant=NCS-1-0;


If any of the mgw-profile token values (from Step 3) need to be changed, use the change mgw-profile command.

Step 5 

add mgw id=CiscoGW50; tsap-addr=192.168.26.104; call-agent-id=CA146; mgw-profile-id=mgwprofile777; type=rgw; aggr-id=cmts777; node=main0044;


Creates the MGW ID for a single eMTA, and specifies values for the other required parameters.

Be sure to set TYPE=RGW for an eMTA.

You must enter the value for AGGR-ID to identify the appropriate CMTS for this eMTA.

The node token allows you to identify a hybrid fiber coax (HFC) node to which the eMTA is assigned. Typically, each eMTA is assigned to a node, and one or more nodes are assigned to a CMTS.

Step 6 

add termination prefix=aaln/; port-start=1; port-end=2; type=LINE; mgw-id=CiscoGW50;


Creates the line termination for the eMTA and specifies values for the required parameters.

For eMTA terminations, always enter type=LINE.

Step 7 

control mgw id=CiscoGW50; target-state=INS; mode=forced;


status mgw id=CiscoGW50;


Brings the eMTA in service (INS state), and verifies that the administrative state is INS.

Step 8 

equip subscriber-termination id=sub3456;


control subscriber-termination id=sub3456; target-state=INS; mode=forced;


status subscriber-termination id=sub3456;


Equips the termination, places it in service (INS state), and verifies that the administrative state is INS.

Provisioning DQoS Parameters for Codec Negotiation Service

The Quality of Service (qos) table is used in providing the codec negotiation service. Codec negotiation is the process the Cisco BTS 10200 Softswitch uses to find a common codec for the compression or decompression of a signal between two gateways. The Subscriber Profile (subscriber-profile) and Subscriber (subscriber) tables point to the qos table.

The following commands allow you to specify the required characteristics for these tables.

SUMMARY STEPS

1. Provision QOS parameters—add qos.

2. Assign a specific QOS to each subscriber-profile or subscriber—
add subscriber-profile; add subscriber.


Note The token values shown in this section are examples.


DETAILED STEPS

 
Command Examples
Purpose

Step 1 

add qos id=Gold1; codec-type=PCMU; client-type=dqos;


Adds a qos with the preferred codec type, specifies client type as DQoS, and other parameters as needed.

You must enter client-type=dqos in this command (and then assign this qos ID to the subscriber or subscriber-profile in the next step) to enable DQoS functionality for the subscriber.

Step 2 

add subscriber-profile id=richardson; dial-plan-id=dp1; POP=BLDG222; qos-id=Gold1;


add subscriber id=Person29; dn1=800-555-0029; sub-profile-id=richardson; term-type=none;


add subscriber id=Person123; dn1=800-555-0123;

sub-profile-id=richardson; qos-id=Gold1; term-type=none;


Assigns a qos ID to each subscriber-profile and/or subscriber.

You must assign the qos ID (the ID of the qos table that was provisioned in the previous step) to the subscriber or subscriber-profile to enable DQoS functionality for the subscriber.

Provisioning TGCP Interfaces to TGWs

This section describes how to provision the TGCP interfaces to the TGWs.

The mgw-profile table provides templates for defining each type of TGW by hardware vendor. It identifies the specifications and settings necessary for communications between the Cisco BTS 10200 Softswitch (which functions as the MGC) and each type of TGW. Several tokens in this table have values that can be overwritten after the Cisco BTS 10200 Softswitch (MGC) queries the TGW for supported capabilities. If the TGW returns a value different from the value originally provisioned in the Cisco BTS 10200 Softswitch, the returned value automatically replaces the originally provisioned value.

SUMMARY STEPS

1. Enable TGCP support for each type of TGW—add mgw-profile.

2. Link each TGW to an mgw-profile—add mgw.

3. Add the trunk termination for a TGW—add termination.

4. Provision QOS parameters—add qos.

5. Assign a QOS-ID to the TGW—add trunk-grp.


Note The token values shown in this section are examples.


DETAILED STEPS

 
Command Examples
Purpose

Step 1 

add mgw-profile id=tgwprf222; vendor=cisco; mgw-type=MGX8850; mgcp-version=MGCP-1-0; mgcp-variant=TGCP-1-0; mgcp-default-pkg=TRUNK; pc-mptime-supp=y;

Creates an mgw-profile for this type of TGW and specifies values for required parameters.

Be sure to set the following values for a TGW:
MGCP-VERSION=MGCP-1-0
MGCP-VARIANT=TGCP-1-0
MGCP-DEFAULT-PKG=TRUNK

Note For most TGWs, set PC-MPTIME-SUPP to Y. However, for a Cisco MGX8850 VISM gateway, the MP function is not available. Therefore, set the PC-MPTIME-SUPP token to N for a Cisco MGX8850 VISM gateway.

Step 2 

add mgw id=tgw50; tsap-addr=TGW1515.cisco.com; call-agent-id=CA146; mgw-profile-id=tgwprf222; type=tgw;


Links a specific TGW to the applicable mgw-profile.

Note Be sure to set TYPE=TGW.

Step 3 

add termination prefix=S0/ds1-2/; mgw-id=tgw50; port-start=1; port-end=24; type=TRUNK;


Creates trunk terminations for the TGW.

Note Be sure to set TYPE=TRUNK.

Step 4 

add qos id=gold-service; lptime=20; hptime=20; codec-type=PCMU; client-type=dqos;

Adds a qos with the preferred codec type, specifies client type as DQoS, and other parameters as needed.

You must enter client-type=dqos in this command (and then assign this qos ID to the trunk-grp in the next step) to enable DQoS functionality for the trunk group.


Caution Provision the same values for lptime and hptime for both MGWs in the call. See the explanation in the qos table in the Cisco BTS 10200 Softswitch Command Line Reference Guide.

Step 5 

add trunk-grp id=101; call-agent-id=CA146; tg-type=ss7; qos-id=gold-service; mgcp-pkg-type=IT; pop-id=chicago333;

Assigns a qos ID and pop ID to each TRUNK-GRP.

For trunk groups on TGCP-based TGWs (MGCP-VARIANT=TGCP-1-0 in the mgw-profile table), set the MGCP-PKG-TYPE value to IT (ISUP trunk package).

You must assign the qos ID (the ID of the qos table that was provisioned in the previous step) to the trunk-grp to enable DQoS functionality for the trunk group.

Provisioning the Keepalive AUEP and ICMP Ping Options

This section explains how to provision the keepalive AUEP and ICMP ping options. There are two tokens to provision:

AUEP and ICMP pings can be globally disabled on the system by use of the mgw-monitoring-enabled token in the Call Agent (call-agent) table.

If globally enabled in the call-agent table, these pings can be selectively enabled or disabled for each mgw-profile by use of the keepalive-method token in the mgw-profile table. Each MGW (eMTA) is linked to an mgw-profile by means of the mgw table.

SUMMARY STEPS

1. Show the setting for mgw-monitoring-enabled—show call-agent.

2. If necessary, change the value of mgw-monitoring-enabled—change call-agent.

3. Show the setting for keepalive-method—show mgw-profile.

4. If necessary, change the value of keepalive-method—change mgw-profile.

5. If necessary, change the value of other keepalive tokens—change mgw-profile.

6. Link individual MGWs (eMTAs) to MGW profiles—add mgw.


Note If mgw-monitoring-enabled=Y (the default value) in the call-agent table, the system checks the provisioning of the keepalive-method token in the mgw-profile table for each MGW.

However, if mgw-monitoring-enabled=N, the AUEP and the ICMP ping are globally disabled, and the keepalive-method token is not checked.


The token values shown in this section are examples. In addition, these tables have many additional optional tokens not shown in these examples. For a complete list of all the tokens for each table, see the Cisco BTS 10200 Softswitch Command Line Interface Reference Guide.

DETAILED STEPS

 
Command Examples
Purpose

Step 1 

show call-agent id=CA146;


The system responds with the current settings for the call-agent table. The default value of mgw-monitoring-enabled is Y.

Show the setting for mgw-monitoring-enabled in the call-agent table.

Step 2 

change call-agent id=CA146; tsap-addr=CA146.cisco.com; mgw-monitoring-enabled=Y;


If the current value of mgw-monitoring-enabled is N, use this command to change it to Y. (Otherwise, go to Step 3.)

Step 3 

show mgw-profile id=mgwprofile001;


The system responds with the current settings for the mgw-profile table.

Show the setting for keepalive-method in the mgw-profile table.

Step 4 

change mgw-profile id=mgwprofile001; keepalive-method=<value (see options)>;


change mgw-profile id=mgwprofile001; keepalive-method=auep-icmp;


If necessary, change the value of keepalive-method in the mgw-profile table.

The options for keepalive-method are:

none—Disable both AUEP and ICMP ping.

auep—Enable AUEP ping but not ICMP ping (this is the default value).

auep-icmp—Enable sending of an AUEP ping followed (if AUEP is unsuccessful) with an ICMP ping.

Step 5 

change mgw-profile id=mgwprofile001; mgcp-keepalive-interval=120; mgcp-keepalive-retries=4; mgcp-max-keepalive-interval=720; mgcp-max1-retries=3; mgcp-max2-retries=4;


If necessary, change the value of other keepalive tokens in the mgw-profile table.

The mgcp-max1-retries and mgcp-max2-retries tokens can be adjusted, if necessary, to improve response if there are network bandwidth or reliability issues, or if an MGW is slow in responding to commands from the CA. For a detailed explanation of how these and other parameters affect the keepalive process, see Appendix C of the Cisco BTS 10200 Softswitch Troubleshooting Guide.

Step 6 

add mgw id=mgw_abc; mgw-profile-id=mgwprofile001;


Links an individual MGW (eMTA) to an mgw-profile.

Provisioning MGCP Command Timeout and QoS Parameters

This section describes the steps required to provision the parameters for MGCP command timeout, silence suppression, and echo cancellation.

MGCP command message timeout is a system-wide MGCP parameter, provisioned in the Call Agent Configuration (ca-config) table.

The QoS parameters for silence suppression and echo cancellation are provisioned in the Quality of Service (qos) table.

 
Command Examples
Purpose

Step 1 

show ca-config
type=mgcp-t-max;


show ca-config type=mgcp-t-hist;


Display the values of MGCP-T-MAX and MGCP-T-HIST.

Parameter Descriptions:

MGCP-T-MAX—The maximum time elapsed since sending of the initial MGCP datagram after which all retransmissions cease. The range is 10 to 60 seconds (default 20 seconds).

MGCP-T-HIST—The maximum time elapsed since sending of the initial MGCP datagram after which the copy of Response is destroyed, even though the MGW does not send ResponseAck. Any message received from the MGW with the same transaction ID after MGCP-T-HIST is considered as new command (and not retransmission). The range is 3 to 120 seconds (default 30 seconds).

Note If more than 2*MGCP-T-HIST has elapsed, the sytem considers the endpoint disconnected, and takes appropriate action.

Tip Keep in mind that the system considers the endpoint disconnected after a period of 2*MGCP-T-HIST, that is, twice the value provisioned for MGCP-T-HIST.

Step 2 

change ca-config type=mgcp-t-max; datatype=integer; value=24;


change ca-config type=mgcp-t-hist; datatype=integer; value=36;

If necessary, change the values of MGCP-T-MAX and MGCP-T-HIST.


Caution MGCP-T-HIST must be greater or equal to MGCP-T-MAX+10. Otherwise the system reverts to the default values for these parameters. (The 10 seconds are added to allow for the maximum propagation delay.)

Note Use the change command if the show command in Step 1 displayed a value for the parameter; otherwise use the add command.

Step 3 

show mgw-profile id=telcomta;


Display the values of EC-SUPP in the mgw-profile table.

Parameter Description:

EC-SUPP—Specifies whether the MGW supports echo cancellation. Values are:

Y—MGW supports echo cancellation

N (default)—MGW does not support echo cancellation

Note The service-provider-provisioned value can be overwritten automatically on the CA upon query from the MGW.

Step 4 

change mgw-profile id=telcomta; ec-supp=y;


If necessary, change the value of EC-SUPP in the mgw-profile table.

Step 5 

show qos id=mta-subscriber;

Display the values of SILENCE-SUPPRESSION and ECHO-CANCELLATION in the qos table.

Parameter Descriptions:

SILENCE-SUPPRESSION—Specifies whether to send the silence suppression parameter to the MGW, and the value (if sent):

NONE (default) = Do not send silence suppression parameter (do not override the existing settings on the MGW).

ON = Silence suppression is ON

OFF = Silence suppression is OFF

ECHO-CANCELLATION—Specifies whether to send the echo cancellation parameter to the MGW, and the value (if sent):

NONE (default) = Do not send echo cancellation parameter (do not override the existing settings on the MGW).

ON = Echo cancellation is ON

OFF = Echo cancellation is OFF

Note The QoS values for silence suppression and echo cancellation provisioned in the Cisco BTS 10200 Softswitch are ignored if the MGCP endpoint reports that it does not support these options during the capabilities audit.

Step 6 

change qos id=mta-subscriber;

silence-suppression=on; echo-cancellation=off;


If necessary, change the values of SILENCE-SUPPRESSION and ECHO-CANCELLATION in the qos table.

Provisioning the Aggregation ID Subnet

Establishing subnets for MTAs enables a service provider to use the Subnet table to statically configure all subnets handled by every Cable Modem Termination System (CMTS). The Cisco BTS 10200 Softswitch uses the IP address of the embedded Multimedia Terminal Adapter (eMTA) and Subnet table to determine the CMTS handling of a particular eMTA. An eMTA is a residential gateway. A CMTS is an aggregation device for multiple eMTAs.

An effective aggr-id is the aggr-id in effect for a particular eMTA. It identifies the CMTS to which the Cisco BTS 10200 Softswitch sends Dynamic Quality of Service (DQoS) requests for that eMTA. A manual aggr-id is an aggr-id that is provisioned by a service provider. If an aggr-id is provisioned in the Media Gateway table or Subnet table, it is a manual aggr-id.

The Cisco BTS 10200 Softswitch uses the following data precedence to decide an MTAs aggr-id:

An MTA's aggr-id is equivalent to its manual aggr-id as long as the manual aggr-id is provisioned in the Media Gateway table (not null).

If an MTA's manual aggr-id is not provisioned, the MTA's effective aggr-id is equivalent to its subnet aggr-id as provisioned in the Subnet table. If a manual aggr-id is not provisioned either in the Media Gateway table or the Subnet table, then DQOS is not applied to the eMTA

This section explains the steps to manually provision subnets for an MTA.

Provision the Media Gateway

This section explains the steps required to provision the residential (media) gateway (eMTA), if it has not already been provisioned. Provisioning an aggr-id for each eMTA is no longer required.

SUMMARY STEPS

1. Add the media gateway profile.

2. Add the media gateway.

3. Add the termination id.

4. Add the subscriber.

DETAILED STEPS

 
Command Examples
Purpose

Step 1 

add mgw-profile id=sa

Add the media gateway profile.

Step 2 

add mgw id=sa1; tsap-addr=<whatever.net>;

Add the media gateway.

Step 3 

add terminati0n id=aaln/1;mgw-id=sa1;sub-id=NULL;

Add the termination id.

Step 4 

add subscriber id=sub1;term-id=aaln/1;

Add the subscriber.

Provision the Subnet

This section explains the steps required to provision a subnet and associate it to an aggregation id. The aggr-id identifies the CMTS on the subnet level. The Cisco BTS 10200 Softswitch determines which subnet an eMTA belongs to by looking at the eMTAs IP address and the subnet's IP prefix. For example, if the eMTAs IP address is 192.168.0.1, then it is on subnet (prefix=192.168.0.0, prefix-length=24). If eMTA is on a provisioned subnet, the provisioned subnet aggr-id is the effective aggr-id for the eMTA.

SUMMARY STEPS

1. Add the media gateway profile.

2. Add the aggregation id for the CMTS.

3. Add the subnet(s).

DETAILED STEPS

 
Command Examples
Purpose

Step 1 

add aggr-profile id=cmts-prof-1; dqos-supp=Y;

Add the aggregation profile.

Step 2 

add aggr id=cmts1; tsap-addr=<cmts-tsap-addr>; aggr-profile-id=cmts-prof-1;

Add the aggregation id for the CMTS.

Step 3 

add subnet subnet-prefix=192.168.0.0;subnet-prefix-length=24; 
aggr-id=cmts1;

add subnet subnet-prefix=192.160.0.0; subnet-prefix-length=24;aggr-id=cmts1;

Add the subnet(s).

Missing Provisioned Data

A CMTS (AGGR) is provisioned in the Aggregation table, but none of the provisioned Subnets refers to that CMTS (AGGR).

Use the following command to audit condition:

report aggr subnet=NONE; 

Provisioning CMTS Discovery Using the Static Subnet Table

To enable CMTS Discovery Using the Static Subnet table, you statically provision the Subnet table in the BTS 10200 system. A service providers must configure all subnets handled by every CMTS using the Subnet table. The BTS 10200 uses the IP address of the multimedia terminal adapter (MTA) and the Subnet table information to determine the CMTS (AGGR) handling the MTA. Figure 5 provides a network diagram of the BTS 10200 to CMTS network connectivity. Figure 6 provides the CMTS to MTA association preference flow.

Figure 5 Network Diagram

Figure 6 CMTS to MTA Association Preference

The BTS 10200 uses the following data precedence to decide MTA Effective-AGGR-ID as shown in Figure 7:

MTA's Effective-AGGR-ID is equivalent to its Manual-AGGR-ID (AGGR-ID provisioned in MGW table) as long as the latter is provisioned NOT NULL.

If MTA Manual-AGGR-ID is not provisioned, MTA Effective-AGGR-ID is equivalent to its subnet's Manual-AGGR-ID (AGGR-ID provisioned in SUBNET table).

Figure 7 MTA Effective-AGGR-ID Data Precedence

Provisioning a Subnet

This section explains the steps required to provision a subnet.

SUMMARY STEPS

1. Ad a subnet.

2. Change a subnet.

3. Delete a subnet.

4. Show a subnet.

DETAILED STEPS

 
Command Examples
Purpose

Step 1 

add subnet 
subnet-prefix=...subnet-prefix-len=...; 

[aggr-id=...;]

Subnet-Prefix (ASCII String, 15 characters)

Subnet prefix in form of IPv4 address xxx.xxx.xxx.xxx

Subnet-Prefix-Len (Integer, 1-32)

Length of Subnet-Prefix, in number of bits.

AGGR-ID (ASCII String, 1-16 characters, default = NULL)

Manual-AGGR-ID provisioned to this subnet. If not NULL, this field must refer to an existing entry in provisioned AGGR table.

Note Overlapping subnets are not allowed or supported.

Step 2 

change subnet  
subnet-prefix=... subnet-prefix-len=...; 

aggr-id=...;

Step 3 

delete subnet subnet-prefix=...

subnet-prefix-len=...;

Step 4 

show subnet 
[subnet-prefix=...; 

subnet-prefix-len=...;]

Provisioning an AGGR-ID

This section explains the steps required to provision an AGGR-ID.

SUMMARY STEPS

1. Void the AGGR-ID provisioned to a single MTA.

2. Force the MTA Effective-AGGR-ID

DETAILED STEPS

 
Command Examples
Purpose

Step 1 

change mgw id=<ABC>; 
aggr-id=NULL;`

This command voids the AGGR-ID provisioned to a single MTA.

At this command, the BTS 10200 will look up the SUBNET table. If the MTA's subnet is found, the subnet's provisioned AGGR-ID will be used as the MTA's Effective-AGGR-ID.

If the AGGR-ID field is already NULL for the MGW, the BTS 10200 will not take any action at the command.

Step 2 

change mgw id=<ABC>; aggr-id=<UVW>;

This command forces the MTA Effective-AGGR-ID to be the one specified in the command

Provisioning the Display of Non DQoS Calls

This section explains the steps required to provision the display of non DQoS calls.

The CLI commands for displaying non DQoS calls are part of the Release 5.0 MR2 enhancement to the CMTS Discovery Using the Static Subnet table.

SUMMARY STEPS

1. Report all MTAs with a specific AGGR-ID.

2. Report all subscribers with a specific AGGR-ID

DETAILED STEPS

 
Command Examples
Purpose

Step 1 

report mgw id=[% | <mgw-id>]; 
oper-status=qos-best-effort; aggr-id=[% | 
<aggr-id>]; LIMIT=<1-35000> ; 
output-type=<csv/xml>; output =<xyz>; 
start_row=[1-100000000]

This command reports all MTAs with a specific AGGR-ID that uses "best-effort" (non DQoS) calls in the network. If no output-type is mentioned, the output will be displayed in the CLI. Otherwise, the user will have the option of specifying the output format. LIMIT is an optional parameter which will be specified if the user has not specified output type. The default value of LIMIT is 50.

The output will display only those media gateways (MGWs) that use the Network-Based Call Signaling protocol (NCS) variant.

The file containing the response will be placed at: /opt/ems/report by default.

Step 2 

report subscriber id=[%]; 
oper-status=qos-best-effort; aggr-id=[% | 
<aggr-id>]; LIMIT=<1-35000> ; type=<csv/xml>;output 
=<xyz>; start_row=[1-100000000]

This command reports all subscribers with a specific AGGR-ID that uses "best-effort" (non DQoS) calls in the network. If no output-type is mentioned, the output is displayed in the CLI. Otherwise, the user will have the option of specifying the output format. LIMIT is an optional parameter which will be specified if the user has not specified output type. The default value of LIMIT is 50.

The output will display only NCS subscribers.

The file containing the response will be placed at: /opt/ems/report by default.

Provisioning the Refreshing of IP Address Cache

This section explains the steps required to provision the refreshing of IP address cache. The CLI commands for refreshing IP address cache CLI commands are part of the Release 5.0 MR2 enhancement to the CMTS Discovery Using the Static Subnet Table feature.

SUMMARY STEPS

1. Update the IP address cache for all MGWs that match the specified subnet.

2. Update the IP address cache of the specified MGW.

DETAILED STEPS

 
Command Examples
Purpose

Step 1 

refresh mgw id=%; category=dns-cache; 
subnet-prefix=<a.b.c.d>; subnet-prefix-len=<n-bits>

This updates the IP address cache for all MGWs that match with the specified subnet if the newly discovered IP address is different. Subnet-prefix and subnet-prefix-len are two optional parameters in this command.

The execution of this command takes a finite amount of time due to asynchronous domain name system (DNS) lookup. The status mgw command shows the refreshed IP address after the command is executed.

Step 2 

refresh mgw id=<mgw-id>; category=dns-cache; 
subnet-prefix=<a.b.c.d>; subnet-prefix-len=<n-bits>

This updates the IP address cache of the specified mgw mentioned in command if the mgw IP address matches with the specified subnet and it is different than the newly discovered IP address. Subnet-prefix and subnet-prefix-len are two optional parameters in this command.

The execution of this command takes a finite amount of time due to asynchronous DNS lookup. The status mgw command shows the refreshed IP address after the command is executed.

Termination Connection Test with the DQoS Diagnostic Command

This section explains the steps required to provision a termination connection test with the DQoS diagnostic commands.

Establishing a termination connection test with the DQoS diagnostic commands are part of the Release 5.0 MR2 enhancement to CMTS Discovery Using the Static Subnet table feature.

SUMMARY STEPS

1. Validate the MTA to CMTS association

DETAILED STEPS

 
Command Examples
Purpose

Step 1 

diag subscriber_termination id=<xyz>; test=4
diag subscriber_termination id=c2421_1;test=?
Matches found:
test; Enter a number from 0 to 4.
===
(1)  Subscriber MGCP Connectivity Test
(2)  Subscriber Termination Connection Test
(3)  Subscriber Termination Ring Test
(4)  Subscriber Termination Connection Test with 
DQoS 
(0)  All

Provides the method to validate the MTA to CMTS association (either by the statically configured AGGR-ID field of the MGW table or by the dynamically learned Effective-AGGR-ID by searching through the static SUBNET table for a given MTA address) by sending a sequence of GateSet/GateDelete message to the CMTS.

Note The DQoS connection test is allowed even if DQOS-SUPP=N in the CALL-AGENT table or DQOS-SUPP=N in the AGGR-PROFILE table or if the endpoint does not support DQoS. For this specific diagnostic test, the BTS 10200 does not rely upon the dynamic capability of the endpoint (reported in AuditEndpoint response message).

Note In earlier releases, the test option (4) represented All Tests. Now option (0) replaces option (4). Option (0) represents all the existing tests including option (4). Option (4) represents the Subscriber Termination Connection Test with DQoS.

Provisioning Subscriber ID Parameters and DQoS Measurement Counter

Packet Cable ECN, DQoS 1.5-N-06.0339-4 was written as part of the Packet Cable 1.5 specification to add Subscriber ID to all Gate Control messages and enhance error codes returned from the CMTS (Cable Modem Termination System).

In the current DQoS specification, the Gate ID is unique only to individual CMTS systems. With the CMTS proxying all CMS (Call Management Server) Gate control messaging through a central device which manages the CMTS connections on the behalf of the CMS, the CMS only has a single COPS (Common Open Policy Service) association to the proxy device. Due to the fact that Gate IDs can be duplicated when using multiple CMTS systems, the ECN defines adding a Subscriber ID to each Gate Control message to disambiguate the Gate IDs between the CMS and proxy device. This particular application is shown in Figure 8:

The ECN DQoS 1.5-N-06.0339-4 augments the following COPS messages, where the Subscriber ID parameter is added:

GATE-INFO

GATE-DELETE

GATE-OPEN

GATE-CLOSE

The Subscriber ID is available at the CMS and is used in the Gate-Set messages.

This ECN also enhances the error codes returned from CMTS or its proxy to allow more precise definition why a particular gate operation may have failed.

Implementation of the above specified ECN is part of this feature. Additionally, some new measurement counters for COPS are added.

Figure 8 Network Diagram

CLI Provisioning and Schema

CLI needs to support the following schema change.

For complete CLI information, see the Cisco BTS 10200 Softswitch Command Line Interface Reference Guide.

AGGR PROFILE TABLE

The AGGR-PROFILE Table is used to define properties of an Aggregation Device, CMTS or PCMM Server.

Table Name: AGGR-PROFILE

Table Containment Area: Call Agent

Command Types

add, audit, change, delete, help, show, sync

Examples

add aggr-profile id=er1; subscriber-id-supp=y;
change aggr-profile id=er1; subscriber-id-supp=n;

Usage Guidelines

Primary Key Token(s): id

Token
PK/FK
Type
Values
M/O

ID

AGGR Profile ID

PK

VARCHAR(16)

1 - 16 ASCII characters.

M

DESCRIPTION

 

VARCHAR(64)

1 - 64 ASCII CHARACTERS

O

SUBSCRIBER-ID-SUPP

Specifies whether to include Subscriber Id in all outgoing Gate Control messages

 

CHAR(1)

Y/N (DEFAULT=N)

O


POP TABLE

Table Name: POP

Table Containment Area: Call Agent, POTS Feature Server, AIN Feature Server

Command Types

add, audit, change, delete, help, show, sync

Examples

add pop id=dallaspop; state=tx; country=usa; aggr-id=proxycmts;

Usage Guidelines

Primary Key Token(s): id

Delete Rules: Foreign key constraints

ID does not exist in any trunk-grp::pop-id.

ID does not exist in any sub-profile::pop-id.

Token
PK/FK
TYPE
Values
M/O

AGGR_ID

Aggregation Device ID

FK

AGGR table

VARCHAR(16)

1 - 16 ASCII Characters

O

ID

PK

VARCHAR(16)

1 - 16 ASCII Characters

M

POLICY_SERVER_ID

Policy server to be used for calls requiring Quality of Service using PacketCable Multimedia model

FK

AGGR table

VARCHAR(16)

1 - 16 ASCII Characters

O


To support this feature, COPS measurement counters and additional DQoS counters were added. For more details, refer to Cisco BTS 10200 Softswitch Operations and Maintenance Guide.

Provisioning Security Interfaces

This section describes the PacketCable-based security interface feature and explains how to provision security options. The subsections are as follows:

Provisioning Parameters for Secured Media

Provisioning Security Interfaces to the MTA

Provisioning Security Interfaces to the CMTS

Provisioning Security Interfaces to the TGW

Provisioning Security Interfaces to the RKS

Provisioning IPsec Security Associations and Ciphersuite Algorithms


Note A global security parameter, IPSEC_ENABLED, must already be set in the initial configuration file (opticall.cfg) during the Cisco BTS 10200 Softswitch software installation process. This parameter enables or disables the IPsec feature on the Cisco BTS 10200 Softswitch. See the detailed requirement in the "Installation" section.


Provisioning Parameters for Secured Media

This section describes how to provision the SECURED-MEDIA-ONLY flag, which affects transmission of security parameters from the qos and ciphersuite tables when the system sets up a call. This parameter affects the setup of calls to unsecured MGWs.

SUMMARY STEPS

1. Show the current setting of the SECURED-MEDIA-ONLY flag—show ca-config.

2. If necessary, change the value of the SECURED-MEDIA-ONLY flag—change ca-config.

DETAILED STEPS

 
Command Examples
Purpose

Step 1 

show ca-config type=SECURED-MEDIA-ONLY;


Displays the current setting of the secured-media-only flag:

If set to Y, the Cisco BTS 10200 Softswitch forces the security parameters from the qos and ciphersuite tables to the endpoint when it sets up the connection. This may result in call failure if either side cannot handle these parameters.

If set to N, the Cisco BTS 10200 Softswitch forces the security parameters from the qos and ciphersuite tables when it sets up the connection to the endpoint only if both sides can handle the security parameters.

Step 2 

change ca-config type=SECURED-MEDIA-ONLY;
datatype=BOOLEAN; value=Y;


If necessary, change the setting of the secured-media-only flag.


Caution Do not change this value unless specified by your network administrator. This command can affect the setup of calls to unsecured MTAs.

The command is shown as change ca-config. However, if the system responds that the parameter does not exist, reenter the command as add ca-config.

Provisioning Security Interfaces to the MTA

The MTA is the only device that uses Kerberos key management. This section explains how to provision the MTA IP security (IPsec) interface, including:

Provisioning Kerberos

Provisioning IPsec policy

Enabling IPsec


Note The token values shown in this section are examples. For detailed token descriptions, see the
Cisco BTS 10200 Softswitch Command Line Interface Reference Guide.


SUMMARY STEPS

1. Provision Kerberos parameters—add ipsec-kerberos.

2. Display the rolling list of old Kerberos service keys—show ipsec-kerberos-keys (optional).

3. Add an IPsec policy for all incoming and outgoing traffic on the MTA—add ipsec-policy.

4. Enter values for additional security parameters—change mgw-profile (optional).

DETAILED STEPS

 
Command Examples
Purpose

Step 1 

add ipsec-kerberos krb-fqdn=cms-ca1.ciscolab.com; krb-realm=cisco-realm.com; krb-srv-key=546869732069732061206b6579206f662032342 06368612e; srv-key-version=8;

Provisions Kerberos parameters.

Note The KRB-FQDN must be the FQDN used on the KDC for this node.

KRB-REALM is used to create the CMS principal name.

If the krb-serv-key is changed, the srv-key-version must also be changed, and if the srv-key-version is changed, the krb-srv-key must also be changed.

Neither krb-srv-key nor srv-key-version, can already exist in the ipsec-kerberos-keys table. The system updates the ipsec-kerberos table before it updates the ipsec-kerberos-keys table.

After you enter a value for the krb-srv-key parameter, the system encrypts it and stores the encrypted value. A show ipsec-kerberos command displays the encrypted value only. There is no way to display the value of the krb-srv-key that you originally entered.

Step 2 

show ipsec-kerberos-keys;


Displays the rolling list of old Kerberos service keys (optional). Use this command when you need to display the list.

Step 3 

add ipsec-policy;

See substeps a and b below.

Adds an IPsec policy for all incoming and outgoing traffic on the MTA. Perform one or more of the following steps, as applicable:

Full-duplex security policy

Using FQDN

Using IP addresses

Half-duplex security policy

a.

Provisioning example using FQDNs:

Use these two commands (examples shown):

add ipsec-policy id=mta01-out; src-fqdn=cms-ca1.ciscolab.com; dest-fqdn=mta1.ciscolab.com; action=apply;

add ipsec-policy id=mta01-in; src-fqdn=mta1.ciscolab.com; dest-fqdn=cms-ca1.ciscolab.com; action=permit;



Alternatively, use this one command (example shown):

add ipsec-policy id=mta01; src-fqdn=cms-ca1.ciscolab.com; dest-fqdn=mta1.ciscolab.com; action=ipsec


Provisioning example using IP addresses:

Use these two commands (examples shown):

add ipsec-policy id=mta02-out; src_ipaddr=192.168.45.211; src_ipmask=255.255.255.0; dest_ipaddr=192.168.17.222; action=apply;

add ipsec-policy id=mta02-in; src_ipaddr=192.168.45.211; src_ipmask=255.255.255.0; dest_ipaddr=192.168.17.222; action=permit;



Alternatively, use this one command (example shown):

add ipsec-policy id=mta02; src_ipaddr=192.168.45.211; src_ipmask=255.255.255.0; dest_ipaddr=192.168.17.222; action=ipsec


Full-duplex security policy—When the MTA vendor applies security policy on all ports, use action=apply for outbound traffic and action=permit for inbound traffic. Alternatively, you can use a single command with action=ipsec for all outbound and inbound traffic.

Note You must specify at least one of the following: src-fqdn, src-ipaddr, or src-port.

You must also specify at least one of the following: dest-fqdn, dest-ipaddr, or dest-port.

The value of the action token defines whether security is applied to outbound or inbound traffic, both, or neither. This is a mandatory token. The allowed values are:

PERMIT—Security on inbound traffic

APPLY—Security on outbound traffic

IPSEC—Security on both inbound and outbound traffic

BYPASS—No security

b.

Use these two commands (examples shown):

add ipsec-policy id=mta01-out; src-fqdn=cms-ca1.ciscolab.com; dest-fqdn=mta1.ciscolab.com; action=apply;

add ipsec-policy id=mta01-in; src-fqdn=mta1.ciscolab.com; dest-fqdn=cms-ca1.ciscolab.com; action=permit; dest-port=2727;


Half-duplex security policy—When the MTA vendor applies security policy on a specific signaling port only, use action=apply for outbound traffic and action=permit and dest-port=<destination port> for inbound traffic.

Step 4 

change mgw-profile id=cvmdqos; krb-reest-flag=[y|n];
ipsec-sa-esp-cs=[cipher suite for ESP]; ipsec-sa-lifetime=[IPsec SA expiration time]; ipsec-sa-grace-period=[expiration grace period];
ipsec-ulp-name=[IP | UDP | TCP]; ike-group=[1|2];
ike-sa-lifetime=[IKE SA expiration time]; ike-cs=[cipher suite for IKE];
ike-key=[IKE pre-shared key];


Enters values for additional security parameters (optional). Use this command only if you need to modify these values in your system.

The default values of these security parameters are sufficient for some networks. Before making any changes, you can use the show command to determine if changes are needed to any of the default values.

After you enter a value for the ike-key parameter, the system encrypts it and stores the encrypted value. A show mgw-profile command displays the encrypted value only. There is no way to display the value of the ike-key that you originally entered.

Provisioning Security Interfaces to the CMTS

This section explains how to provision security interfaces to the CMTS.

SUMMARY STEPS

1. Add a security policy for the CMTS—add ipsec-policy.

2. Enables IPsec for the CMTS—change aggr.

3. Enter values for additional security parameters for this CMTS—change aggr (optional).


Note The token values shown in this section are examples.


DETAILED STEPS

 
Command Examples
Purpose

Step 1 

add ipsec-policy id=cmts01; src-fqdn=cms-ca1.ciscolab.com; dest-fqdn=cmts1.ciscolab.com; action=ipsec;


Adds a security policy for the CMTS.

Step 2 

change aggr id=cmts1; tsap-addr=[DNS/IP-address]; ike-key=<IKE preshared security key>;


Enables IPsec for the CMTS.

After you enter a value for the ike-key parameter, the system encrypts it and stores the encrypted value. A show aggr command displays the encrypted value only. There is no way to display the value of the ike-key that you originally entered.

Step 3 

change aggr id=cmts1; tsap-addr=[DNS/IP-address]; ipsec-sa-esp-cs=[cipher suite for ESP]; ipsec-sa-lifetime=[IPsec SA expiration time]; ipsec-sa-grace-period=[expiration grace period]; ipsec-ulp-name=[IPsec SA upper layer protocol]; ike-group=[1|2]; ike-sa-lifetime=[IKE SA expiration time]; ike-cs=[cipher suite for IKE]; ike-key=234; description=CMTS_City1;


Enters values for additional security parameters for this CMTS (optional). Use this command only if you need to modify these values in your system.

The default values of these security parameters are sufficient for some networks. Before making any changes, you can use the show command to determine if changes are needed to any of the default values.


Note The aggr id and tsap-addr are both required in this command.


Provisioning Security Interfaces to the TGW

This section explains how to provision security interfaces to the TGW.

SUMMARY STEPS

1. Add a security policy for the TGW—add ipsec-policy.

2. Enable IPsec for the TGW—change mgw-profile.

3. Enter values for additional security parameters for this TGW—change mgw-profile (optional).


Note The token values shown in this section are examples.


DETAILED STEPS

 
Command Examples
Purpose

Step 1 

add ipsec-policy id=tgw01; src-fqdn=cms-ca1.ciscolab.com; dest-fqdn=tgw1.ciscolab.com; action=ipsec;


Adds a security policy for the TGW.

You must specify at least one source (src-fqdn, src-ipaddr, or src-port), and at least one destination (dest-fqdn, dest-ipaddr, or dest-port).

Note You cannot specify both a SRC-FQDN and a SRC-IPADDR at the same time. You cannot specify both a DEST-FQDN and a DEST-IPADDR at the same time.

Step 2 

change mgw-profile id=tgw1; ike-key=<IKE preshared security key>;


Enables IPsec for the TGW—To enable IPsec on the TGW, change the mgw-profile entry associated with this TGW.

Note Changing this entry enables security for all TGWs that use this profile, so you might want to have a security-enabled and security-disabled profile for each vendor class.

After you enter a value for the ike-key parameter, the system encrypts it and stores the encrypted value. A show mgw-profile command displays the encrypted value only. There is no way to display the value of the ike-key that you originally entered.

Step 3 

change mgw-profile id=cvmdqos; krb-reest-flag=[y|n]; ipsec-sa-esp-cs=[cipher suite for ESP]; ipsec-sa-lifetime=[IPsec SA expiration time]; ipsec-sa-grace-period=[expiration grace period]; ipsec-ulp-name=[IP | UDP | TCP]; ike-group=[1|2]; ike-sa-lifetime=[IKE SA expiration time]; ike-cs=[cipher suite for IKE]; ike-key=[IKE pre-shared key];


Enters values for additional security parameters for this mgw-profile (optional). Use this command only if you need to modify these values in your system.

The default values of these security parameters are sufficient for some networks. Before making any changes, you can use the show command to determine if changes are needed to any of the default values.

Provisioning Security Interfaces to the RKS

This section explains how to provision security interfaces to the RKS.

SUMMARY STEPS

1. Add a security policy for the RKS—add ipsec-policy.

2. Enables IPsec for the primary and secondary RKS units—change radius-profile.

3. Enter values for additional security parameters for this RKS—change radius-profile (optional).


Note The token values shown in this section are examples.


DETAILED STEPS

 
Command Examples
Purpose

Step 1 

add ipsec-policy id=rks01; src-fqdn=cms-ca1.ciscolab.com; dest-fqdn=rks1.ciscolab.com; action=ipsec;


Adds a security policy for the RKS.

You must specify at least one source (src-fqdn, src-ipaddr, or src-port), and at least one destination (dest-fqdn, dest-ipaddr, or dest-port).

Note You cannot specify both a SRC-FQDN and a SRC-IPADDR at the same time. You cannot specify both a DEST-FQDN and a DEST-IPADDR at the same time.

Step 2 

change radius-profile id=[primary RKS id | secondary RKS id]; tsap-addr=[ip-address | ip-address:port-number]; ike-key=<IKE preshared security key>;


Enables IPsec for the primary and secondary RKS units.

After you enter a value for the ike-key parameter, the system encrypts it and stores the encrypted value. A show radius-profile command displays the encrypted value only. There is no way to display the value of the ike-key that you originally entered.

Step 3 

change radius-profile id=[primary RKS id | secondary RKS id]; tsap-addr=[ip-address | ip-address:port-number]; ipsec-sa-esp-cs=[cipher suite for ESP]; ipsec-sa-lifetime=[IPsec SA expiration time]; ipsec-sa-grace-period=[expiration grace period]; ipsec-ulp-name=[SA upper layer protocol]; ike-group=[1|2]; ike-sa-lifetime=[IKE SA expiration time]; ike-cs=[cipher suite for IKE];


Enters values for additional security parameters for this radius-profile (optional). Use this command only if you need to modify these values in your system.

The default values of these security parameters are sufficient for some networks. Before making any changes, you can use the show command to determine if changes are needed to any of the default values.

Provisioning IPsec Security Associations and Ciphersuite Algorithms

This section explains how to provision the IPsec security associations (SAs) and the ciphersuite encryption and authentication algorithms.

The IPsec SA (ipsec-sa) table contains the IPsec SAs that are not associated with IKE or Kerberos key management.

A cipher is an algorithm that transforms data between plain text and encrypted text. A ciphersuite consists of both an encryption algorithm and a message authentication algorithm. The Ciphersuite Profile (ciphersuite-profile) and Ciphersuite (ciphersuite) tables provision the allowed ciphersuites for media security (encryption of bearer-path data) between two MTAs.

SUMMARY STEPS

1. Add a security association for a device—add ipsec-sa.

2. Create a ciphersuite profile—add ciphersuite-profile.

3. Create the ciphersuite data supporting the ciphersuite profile—add ciphersuite.


Note The token values shown in this section are examples. For a complete list of tokens and detailed descriptions, see the Cisco BTS 10200 Softswitch Command Line Interface Reference Guide.


DETAILED STEPS

 
Command Examples
Purpose

Step 1 

add ipsec-sa id=cmts01; auth-algo=HMAC-SHA-1; auth-key=2069732061206b6579206f66203234206368612e; dest=10.10.7.7; encrypt-algo=DES; encrypt-key=4bb586a120532c07; spi=-85723; src=10.10.2.2; soft-lifetime=3600; hard-lifetime=7200;


Adds a security association for a device.

The range of values is 1 to 8 ASCII characters. The suggested format is <device-type>NN, for example, mta01, cmts01, rks01. This token is mandatory.

After you enter a value for the auth-key and encrypt-key parameters, the system encrypts them and stores the encrypted values. A show ipsec-sa command displays the encrypted values only. There is no way to display the values that you originally entered for these two parameters.

Step 2 

add ciphersuite-profile id=cp1gold; description=This ID is used for QoS gold.


Creates a ciphersuite-profile.

Step 3 

add ciphersuite id=cp1gold; proto-type=RTP; auth-algo=RTP-MMH-4; encrypt-algo=RTP-3DES-CBC; priority=1;


add ciphersuite id=cp1gold; proto-type=RTCP; auth-algo=RTCP-HMAC-MD5-96; encrypt-algo=RTCP-AES-CBC; priority=1;


Creates the ciphersuite data supporting the ciphersuite-profile.

Provisioning Event Messages

This section explains how to provision EM functionality on the Cisco BTS 10200 Softswitch. It includes the following tasks:

Provisioning Support for EM Transmission and Storage

Provisioning the System to Generate EMs for Billing

Provisioning Media_Alive Verification for EMs

Provisioning Support for EM Transmission and Storage

The commands in the following procedure specify the required IDs for the primary and secondary RKSs and link them with the Call Agent (CMS/MGC). They also control parameters related to the transmission of EMs to the RKS and parameters related to storage of EMs on the CA.

The RADIUS Profile (radius-profile) table is required in PacketCable networks that use an EM-based billing system and a RADIUS-based Record Keeping Server (RKS). This table includes provisionable parameters such as primary and secondary RKS node IDs, IP address and port address, RADIUS retry intervals and retry counts.

The call-agent-profile table establishes a link between the Call Agent (CMS) and the primary and secondary RKSs.

SUMMARY STEPS

1. Create the interfaces to the primary and secondary RKSs—add radius-profile.

2. Specify parameters for storage of EM files on the CA—change ca-config.

3. Provision batch mode handling of EMs—change ca-config.

4. Set the DSCP for signaling packets on RADIUS interfaces between the CMS and RKS—change ca-config.

5. Set the EM privacy indicator token if you want the system to populate the privacy indicator field in the EMs—change ca-config.

DETAILED STEPS

The token values shown in this section are examples. These tables have many additional optional tokens not shown in these examples. For a complete list of all the tokens for each table, see the Cisco BTS 10200 Softswitch Command Line Interface Reference Guide.

DETAILED STEPS

 
Command Examples
Purpose

Step 1 

add radius-profile id=prirks; tsap-addr=192.168.100.100; encryption-key=abcdef1234567890; acc-rsp-timer=7;  acc-req-retransmit=4; description=primary_billing_server


add radius-profile id=secrks; tsap-addr=192.168.100.101; encryption-key=abcdef1234567890; acc-rsp-timer=6;  acc-req-retransmit=2; description=secondary_billing_server


Creates the interfaces to the primary and secondary RKS units and sets values for various parameters.

The ACC-RSP-TIMER and ACC-REQ-RETRANSMIT tokens control the retransmission of EMs from the CA to the RKSs when the first attempt does not go through. ACC-RSP-TIMER controls how long the system waits before retransmitting, and ACC-REQ-RETRANSMIT controls how many retransmission attempts are made to the target RKS.

Step 2 

change ca-config type=retry-pri-rks-timer; datatype=integer; value=14;

change ca-config type=em-file-open-time; datatype=integer; value=900;

change ca-config type=em-file-size; datatype=integer; value=50;


Specifies how the system stores EMs in files on the CA (when loss of communication with the RKSs prevents EMs from being transmitted to the RKSs).

An open EM file does not close automatically when communication to the RKS is restored. The file closes automatically according to the provisioned value in EM-FILE-OPEN-TIME or EM-FILE-SIZE, whichever occurs first.

The command is shown as change ca-config. However, if the system responds that the parameter does not exist, reenter the command as add ca-config.

Step 3 

change ca-config type=batch-mode-supp; value=Y;

change ca-config type=batch-latency; value=240;


Provisions batch mode handling of EMs.

The command is shown as change ca-config. However, if the system responds that the parameter does not exist, reenter the command as add ca-config.

Step 4 

change ca-config type=RADIUS-DSCP-TOS; value=96;


Sets the DSCP for signaling packets on RADIUS interfaces between the CMS and RKS.

The default values for this parameter might be adequate for your specific case. We do not recommend that you change this value unless necessary, and recommend that you contact Cisco TAC regarding any plans to change it.

The command is shown as change ca-config. However, if the system responds that the parameter does not exist, reenter the command as add ca-config.

Step 5 

change ca-config type=EM-PRIVACY-IND-SUPP; datatype=BOOLEAN; value=Y;


Instructs the system to include the privacy-indicator field in the signaling start EM. For details of this field, see the "EM Generation Details and Content" section.

This change takes effect immediately when provisioned. It is not necessary to restart any platforms.

The command is shown as change ca-config. However, if the system responds that the parameter does not exist, reenter the command as add ca-config.

Provisioning the System to Generate EMs for Billing

The Cisco BTS 10200 Softswitch can provision billing support using either call detail blocks (CDBs), which are assembled into call detail records (CDRs) by an external billing server, or PacketCable EMs, which are transferred to an external RKS that assembles CDRs from the EMs.

The Cisco BTS 10200 Softswitch contains two PacketCable-based logical network elements, the CMS and MGC. The CMS and MGC have provisionable element IDs as described in this section. The applicable element ID is included in each EM sent from the CMS or MGC.

To provision the Cisco BTS 10200 Softswitch to generate EMs for billing, complete the steps shown in the following section.

SUMMARY STEPS

1. Display the current CA profile—show call-agent-profile.

2. Modify CA profile parameters related to EM generation and RKS profiles, if necessary—change call-agent-profile.

3. Identify the CMS and MGC logical network elements, and the financial entity ID (FEID)—change call-agent-profile.

4. (Optional) Provision a billing type (flat rate or measured rate) and an account ID for individual subscribers—change subscriber.

DETAILED STEPS

The token values shown in this section are examples. In addition, these tables have many additional optional tokens not shown in these examples. For a complete list of all the tokens for each table, see the Cisco BTS 10200 Softswitch Command Line Interface Reference Guide.

DETAILED STEPS

 
Command Examples
Purpose

Step 1 

show call-agent-profile id=CA146;


Displays the current parameters for the CA profile.

Step 2 

change call-agent-profile id=CA146; cdb-billing-supp=N; em-billing-supp=Y; pri-rks-profile-id=prirks; sec-rks-profile-id=secrks;


add call-agent-profile id=CA146; cdb-billing-supp=N; em-billing-supp=Y; pri-rks-profile-id=prirks88; sec-rks-profile-id=secrks88;


If the system response (in the display from Step 1) contains data, use the change call-agent-profile command if you want to change any of the parameter values.

If the system response (in the display from Step 1) indicates that this table does not exist, then you must create it using the add call-agent-profile command. Otherwise, the EM function is not supported and EMs are not generated.


Caution If the call-agent-configuration table is not created, the Cisco BTS 10200 Softswitch generates CDBs but not EMs.
EM and CDB Billing Options

In a PacketCable network, the service provider can choose EM-based billing or CDB-based billing.


Caution We strongly recommend that you do not set both of these tokens (EM and CDB billing support) to y. Attempting to generate both types of records simultaneously can significantly degrade system performance.

Note To set both tokens to y, you must also include forced=y in the command line.

Note Provisioning changes for cdb-billing-supp and em-billing-supp take effect only after a CA switchover or restart.

RKS IDs

The value for pri-rks-profile-id (primary RKS profile ID) must be the same as the value for the radius-profile ID for the primary RKS, and the value for sec-rks-profile-id (secondary RKS profile ID) must be the same as the radius-profile ID for the value for the secondary RKS.

Step 3 

change call-agent-profile id=CA146; cms-id=12345; mgc-id=67890; feid=feid0001;


Identifies the CMS and MGC logical network elements and the financial entity ID (FEID). The system uses these IDs when generating EMs.

The Cisco BTS 10200 Softswitch contains both the CMS and MGC logical entities. For PacketCable systems, the CMS-ID must be entered. If your Cisco BTS 10200 Softswitch communicates with a TGW, you must enter the MGC-ID. The FEID value is also required for EM billing.

You must provision the CMS-ID and MGC-ID tokens so that the Cisco BTS 10200 Softswitch can provide support for the Communication Assistance for Law Enforcement Act (CALEA). For provisioning procedures related to CALEA support, see the Cisco BTS 10200 Softswitch Provisioning Guide.

Step 4 

change subscriber id=SUB5551212; sub-profile-id=profile777; account-id=123456789; billing-type=FR2;

(Optional) Provision a billing type (flat rate or measured rate) and an account ID for individual subscribers.

Provisioning Media_Alive Verification for EMs

Use the Activity (activity) table to schedule and configure Media_Alive EMs. These EMs are used during longer-duration calls to verify that the media connection is still alive. For information on these operational commands, see the "Viewing Media_Alive Verification for EMs" section.

For an additional sample provisioning sequence, see the Cisco BTS 10200 Softswitch Provisioning Guide. For additional reference information on CLI tables and parameters, see the Cisco BTS 10200 Softswitch Command Line Interface Guide.

Provisioning PCMM-Based QoS for Type 1 Clients

The PCMM-based QoS capability includes the following CLI database changes beginning with Release 5.0:

A new table, POLICY-SERVER, is added; it uses the existing AGGR table to store the policy server (PS) provisioning data.

A field is added to the existing POP table to identify the PS used for the subscribers or trunk groups in a specific POP.

A new table, AGGR-PROFILE, is added. Several fields in the existing AGGR table are moved to the AGGR-PROFILE table.

The BTS 10200 uses the AGGR table for maintaining a COPS connection with the PS. The POLICY-SERVER table, which is an alias to the AGGR table, is provided to distinguish between the CMTS-type of COPS client and the PS-type of COPS client.


Tip In DQoS, the CMTS is assigned at the MGW level. In PCMM, the PS is assigned at POP level.


Office Provisioning—Configure PCMM Support, Policy Server, and QoS


Step 1 Enable PCMM support. The default value of pcmm-supp is N (no), so you must change it to Y to enable PCMM support on the switch.

change call-agent-profile id=CA146; pcmm-supp=Y;

Step 2 (Optional) Add the aggr-profile for the PS. This is necessary only if you need to tune timing or gate-coordination parameters for the PS.

add aggr-profile id=ps-profile; <additional parameters as needed>;

Step 3 Add the PS.

add policy-server id=ps-dallas; tsap-addr=ps@dallas.cisco.com

Note If you added an aggr-profile in Step 2, this command should also include aggr-profile-id=ps-profile;


Step 4 Change the POP table to reference the policy-server ID.

change pop id=pop-dallas; policy-server-id=ps-dallas;

Step 5 Change the CLIENT-TYPE field in the QoS table to use PCMM.

change qos id=qos-pcmm; client-type=mm-cops;


Configuring Subscribers and Trunk Groups to Use PCMM-Based Admission Control


Step 1 To provide PCMM to the subscriber, change the Subscriber-Profile or Subscriber table to reference the QOS ID.

change subscriber-profile id=sub-1; qos-id=qos-pcmm;

or

change subscriber id=sub-1; qos-id=qos-pcmm;

Step 2 To provide PCMM to a trunk group, change the Trunk-Group table to reference the QOS ID.

change trunk-grp id=99; qos-id=qos-pcmm;


CA Configuration and Aggr Profile Parameters

Table 1 lists the parameters that have been moved from the ca-config table to the aggr-profile table in Release 5.0.

Table 1 Change in Existing Configuration Parameters 

Old Configuration Parameter
Replaced by New Configuration Parameter

DQOS-T1-TIMER (CA-CONFIG table)

gate-authorized-timer (AGGR-PROFILE table)

DQOS-T5-TIMER (CA-CONFIG table)

gate-close-timer (AGGR-PROFILE table)

DQOS-T7-TIMER (CA-CONFIG table)

gate-reserved-timer (AGGR-PROFILE table)

DQOS-T8-TIMER (CA-CONFIG table)

gate-committed-timer (AGGR-PROFILE table)

DQOS-GATE-TIMER (CA-CONFIG table)

ack-timeout (AGGR-PROFILE table)


Additionally, the new timer gate-committed-recovery-timer was added to the AGGR-PROFILE table, and the new configuration parameter BEST_EFFORT_ON_QOS_FAIL was added to the ca-config table.

Status, Control, and Reset Commands

For maintenance commands related to the CMTS and PS, see the "Reset, Control, and Status Commands" section.

Provisioning AuditConnection Parameters

The system uses the AuditConnection command to audit the status of connections to any MGCP-based endpoint. This allows the system to discover call identifiers corresponding to stray connections, that is, connections which exist on an MGCP endpoint but are not accounted for on the Cisco BTS 10200 Softswitch. An example of a stray connection is a ringing endpoint for which no call is being set up. These stray connections can occur, for example, on endpoints that were engaged in a three-way call (TWC) during a CA failover. The system can send an AuditConnection command to recover the connection state from the MGCP device after a CA failover. A provisionable parameter in the Cisco BTS 10200 Softswitch database allows the service provider to enable or disable the AuditConnection functionality for each MGW profile. The system uses the MGCP-compliant DeleteConnection command to clear stray connections.

This section describes the steps required to provision the AuditConnection functionality for each MGW profile.


Note In Release 5.0, the MGCP-AUCX-SUPP token is introduced. The MGCP-XDLCX-SUPP token (from previous releases) is not provided.


SUMMARY STEPS

1. show mgw-profile

2. change mgw-profile

DETAILED STEPS

 
Command Examples
Purpose

Step 1 

show mgw-profile id=telcomta


Display the value of MGCP-AUCX-SUPP in the mgw-profile table.

Parameter Description:

MGCP-AUCX-SUPP—Specifies whether AuditConnection command is enabled or disabled. Values are:

Y (default)—AuditConnection command is enabled

N—AuditConnection command is disabled

Step 2 

change mgw-profile id=telcomta mgcp-aucx-supp=y;


If necessary, change the value of MGCP-AUCX-SUPP in the mgw-profile table.

Operations, Billing, and EM Transfer Procedures

This section covers the operational features of the Cisco BTS 10200 Softswitch PacketCable implementation, including the following topics:

PacketCable Billing Data and Formats in Deployments Using CDBs

Reset, Control, and Status Commands

Manual Recovery and Transfer of Stored EMs

Viewing Media_Alive Verification for EMs

Measurements

Events and Alarms

PacketCable Billing Data and Formats in Deployments Using CDBs

For deployments that use CDBs for billing (rather than EMs), the following CMTS and eMTA identifying information is included in the CDBs:

Billing field 82, Overall correlation identifier

Billing field 158, originating end point TSAP address

Billing field 159, terminating end point TSAP address

Billing field 160, originating CMTS ID

Billing field 161, terminating CMTS ID

Billing field 162, originating fiber node ID

Billing field 163, terminating fiber node ID

Billing field 223, originating call admission control (CAC) type

Billing field 224, terminating call admission control (CAC) type

See the Appendix A of the Cisco BTS 10200 Softswitch Billing Guide for a complete list of billing fields and field contents, and a description of the options for CDB file-naming conventions.

Reset, Control, and Status Commands

This section describes the reset, control, and status commands for aggr and policy-server.

Reset

To provide the functionality of resetting the TCP connections to the CMTS and PS, the BTS 10200 implements a reset command for the AGGR (CMTS) or PS. The system closes and reinitiates the TCP connection and COPS session to the CMTS or PS when the operator executes the following CLI command:

reset aggr id=CMTS1;
reset policy-server id=PS-DALLAS;

If an AGGR or POLICY-SERVER is in any operational state other than in service (INS), for example if the AGGR or POLICY-SERVER is operationally out of service (OOS) or transitioning between operational states, the system does not execute the reset. It responds to the reset command by displaying a failure message.

Control

The system implements control command for the AGGR. There are only two possible administrative states for AGGR (CMTS/PS) IN-SERVICE and OUT-OF-SERVICE.

For control out-of-service with mode set to forced/graceful, the Cisco BTS 10200 Softswitch closes the TCP connection (thus COPS session) to CMTS or PS when operator takes the AGGR out-of-service by executing the following CLI command. After you control the aggr or policy-server OOS, the BTS 10200 does not attempt to set up any new calls through this aggr or policy-server. Existing calls may or may not be affected depending upon the CMTS implementation.

control aggr id=CMTS1; target-state=OOS; mode=forced;
control policy-server id=PS-DALLAS; target-state=OOS; mode=forced;

The system initiates a set up for TCP as well as a COPS connection to the CMTS or the PS when the operator brings the AGGR into in-service mode by executing the following CLI command:

control aggr id=CMTS1; target-state=INS; mode=forced;
control policy-server id=PS-DALLAS; target-state=INS; mode=forced;

Status

The system shows the operational state when the operator queries the current status of TCP and COPS connection associated with the CMTS or PS:

status aggr id=CMTS1;
status policy-server id=PS-DALLAS;

Example:

status aggr ID=c7246-777;

ID -> c7246-777
OPER STATE -> AGGR IN Service
RESULT -> ADM configure result in success
REASON -> ADM executed successfully

For the STATUS AGGR command, the available displayed values include INS (in service), OOS (out of service), and CONNECTING. CONNECTING state means that the Cisco BTS 10200 Softswitch is reattempting to connect to the CMTS.

For a DQoS/PCMM subscriber, Cisco BTS 10200 first checks whether AGGR_ID is provisioned in the MGW table. If it's not provisioned in the MGW table, BTS 10200 looks for the AGGR_ID value provisioned in the SUBNET table (that is, the AGGR_ID value is resolved using the value provisioned in the SUBNET table).

If the AGGR_ID is provisioned (resolved), BTS 10200 checks the status of AGGR or POLICY_SERVER table. For a DQoS/PCMM call, if the AGGR or POLICY_SERVER operational state is not INS, and the BEST_EFFORT_ON_QOS_FAIL flag is set to N, the system drops the call. If the AGGR or POLICY_SERVER operational state is not INS, and the BEST_EFFORT_ON_QOS_FAIL flag is set to Y, the system continues the (DQoS/PCMM) call on a best-effort basis.

If the AGGR_ID is not provisioned in the MGW or SUBNET table, BTS 10200 lets the call to continue on a best-effort basis.


Note If the AGGR_ID is not provisioned for a tapped (CALEA) subscriber, then all non-emergency calls are blocked.


Manual Recovery and Transfer of Stored EMs

This section describes how to manually recover and transfer stored EM files from the CA to the RKS. This procedure must be used if communication to both RKS units goes down. Perform these procedures after communication is restored.

Recovering the Billing Files


Note For information on compliance with specific paragraphs of PacketCable standards and ECNs, contact your Cisco account team.


Billing data is normally transferred to the RKS on a real-time basis. In the unlikely event that communications with the RKS go down, alarms are raised and billing data files are written to a local drive on the Cisco BTS 10200 Softswitch (see the /opt/BTSem directory on the Call Agent (CA) that generated the EMs). If communications are not promptly restored, additional billing alarms of increasing severity are raised at time intervals of 1 hour (minor), 3 hours (major), and 5 hours (critical).

EMs that are not successfully transferred to the RKS are stored on the Call Agent. The system uses the naming conventions specified in PacketCable ECN EM-N-04.0186-3 for the stored EMs. Here is the format for the file name:

PKT_EM_<yyyymmddhhmmss>_<priority>_<record type>_<node id>_<sequence>.bin

The parameters are defined as follows:

PKT_EM is fixed and does not change across files.

yyyymmddhhmmss is a timestamp, where:

yyyy is the year, such as 2005

mm is the month, from 01 through 12

hh is the hour, from 00 through 23

mm is the minute, from 00 through 59

ss is the second, from 00 through 59

priority is always set to 3.

record type is always set to 0.

node id is the CMS ID or MGC ID. It must be five digits long and padded with leading 0s if necessary. (The system uses the CMS ID or the MGC ID depending on whether the file contains EMs generated by the CMS or the MGC function of the Call Agent.)

sequence is the file sequence number. It must be six digits long, padded with leading 0s if necessary. (The CMS and MGC files are numbered independently.)

.bin is the binary file type designation.

Here is an example of a typical EM file name:

PKT_EM_20050915103142_3_0_01234_000002.bin

All billing data generated during the period of the communication outage is stored in the /opt/BTSem directory. If communication with the RKS is lost for an extended period, the available disk space on the local Softswitch drives can begin to fill up with EM files. The system monitors the amount of space available on the disks and raises alarms of increasing severity when the disks are 50 percent (minor), 70 percent (major) and 100 percent (critical) full.


Note There can be billing data files on both CAs, primary and secondary, depending on whether there have been any switchovers during the loss of communication with the RKS.


We recommend that you monitor the available disk space on a regular basis to prevent the possible loss of billing data. If the disks become full, the data on the disk is preserved and new EMs are discarded.


Caution Do not allow the disk to become full. If you do not transfer the billing data files to the RKS, billing data might be lost. If EMs are discarded, they cannot be recovered and revenue could be lost.

Sending Billing Files to the RKS via FTP

To send billing files from the CA to the RKS, perform the following steps:


Step 1 On the CA, navigate to the subdirectory to which the billing data is written.

cd /opt/BTSem


Step 2 At the prompt, establish an FTP session with the RKS.

ftp <RKS name>


Step 3 When prompted, enter your user name and password for the RKS. The FTP prompt should appear.

Step 4 At the FTP prompt, enter bin to enable binary transfer:

bin


Step 5 On the RKS, navigate to the subdirectory to which the billing files will be written.

cd /.../.../<billing file subdirectory name>


Step 6 Place the applicable billing files in the billing files subdirectory.

put <billing-filenames>


Step 7 After the transfer is complete and the FTP prompt reappears, exit the FTP session.

bye


Comparing Checksums

To compare the checksums to ensure that the data was transferred correctly, perform the following steps:


Step 1 Log in to the RKS, using your user name and password for that system.

Step 2 Navigate to the subdirectory to which the billing data files were written.

cd /.../.../<billing file subdirectory name>


Step 3 List the files in the billing directory. The following command lists the files in reverse order by creation date:

ls -lrt


Step 4 Run a cksum on the files that were backed up.

cksum <billing-filename>


Step 5 Compare these cksum values to the corresponding cksum values on the CA.

a. If the cksum values are the same, the file transfer has completed without error.

b. If the cksum values are not the same, repeat all of the steps in the "Sending Billing Files to the RKS via FTP" section and "Comparing Checksums" section.

If the cksum values are still different, contact Cisco TAC for assistance.


Content of EMs Sent to the RKS

Following is an example of a typical EM sent by the Cisco BTS 10200 Softswitch to an RKS. The format of the event-time field is yyyymmddhhmmss.mmm, where .mmm refers to milliseconds.

EM-Header (1):
version: 4 
bci: 3378049121- 55555-58 (STD, -06:00:00) 
event-type: Signaling Start (1) 
element-type: CMS (1) 
element-id: 55555 
zone: STD, -06:00:00 
sequence-number: 618 
event-time: 20070117125847.132 
status: 0 
priority: 128 
attribute-count: 6 
event-object: 1 
Direction-Indicator (37): Originating (1)

Viewing Media_Alive Verification for EMs

Use the activity table to schedule and configure Media_Alive EMs. These EMs are used during longer-duration calls to verify that the media connection is still alive.


Step 1 Configure Media_Alive generation according to local requirements (example shown here):

add activity id=MEDIA-ALIVE-EM; freq=6H; start-time=HH:MM;

where:

id—The value must be MEDIA-ALIVE-EM, which is a fixed system value listed in the Activity Base (activity-base) table.


Note You can view other tokens in the activity-base table by using the command show activity-base. However, you cannot change any values in that table.


freq—Frequency. The number of times to schedule the specified EM Media_Alive activity.

start-time—Time of day in the format HH:MM ranging from 00:00 to 23:59 (default is 00:00).


Note The activity table has several other tokens that support other EM Media_Alive options. For more detailed information about these options, see the Cisco BTS 10200 Softswitch Command Line Interface Reference Guide.


Step 2 To view the MEDIA-ALIVE-EM activity, enter the following command:

show activity id=MEDIA-ALIVE-EM;

Sample command line output:

ID=MEDIA-ALIVE-EM

FREQ=30 MINUTES

DAY_OF_MONTH=NA

DAY_OF_WEEK=NA

START_TIME=00:00

FIXED_TIME_INTERVAL=N

ENABLED=N

SO_ENABLED=N

RESTART_ENABLED=N

LAST_CHANGED=2004-10-20 16:45:30


Measurements

Several traffic measurements pertain to the PacketCable implementation. For detailed descriptions see the Traffic Measurements section in the Cisco BTS 10200 Softswitch Operations and Maintenance Guide.

Creating Reports and Displays of Measurements

This section outlines the procedure for creating reports and displays of measurements. It uses the DQoS feature as an example. Additional details about measurement provisioning, reporting, and display commands for all features can be found in the Cisco BTS 10200 Softswitch Operations Guide and the Cisco BTS 10200 Softswitch Command Line Interface Reference Guide.

To create a report file of the DQoS counters for all time intervals in the period starting and ending at specific times, enter the following command. The system prepends the file with the string "Tm_" and writes the file to the /opt/ems/report directory on the active EMS.

report measurement-dqos-summary; start-time=[start-time]; end-time=[end-time]; aggr-id=[ID 
of the aggregation router (CMTS) for which data should be reported]; output=[desired file 
name for the report]; output-type=[CSV | XML];

where:

start-time and end-time have the format yyyy-mm-dd hh:mm:ss

CSV = comma-separated value


Note Time intervals can be every 5, 15, 30, or 60 minutes. This is provisionable in another command, change measurement-prov, as described later in this section.


Use any of the following commands to display DQoS counters on your monitor.


To display DQoS counters for all time intervals in the past 48 hours for all CMTS IDs, enter the following command:

report measurement-dqos-summary; interval=ALL;

To display DQoS counters tracked at every interval in the period starting at a specific start-time and for all aggregation IDs, enter the following command:

report measurement-dqos-summary; start-time=[start-time];

(start-time has a format of yyyy-mm-dd hh:mm:ss, and the end-time defaults to the most 
recent interval)

To display DQoS counters for the most recent time interval for all aggregation IDs, enter the following command:

report measurement-dqos-summary;

(start-time and end-time both default to the most recent interval)

In this example, the system displays the most recent time interval for all aggregation IDs:

report measurement-dqos-summary
Reply: Request was successful.
TIMESTAMP       20020310184428
DQOS_GATESET_ATTMP       10
DQOS_GATESET_SUCC         9
DQOS_GATE_COMMIT          9

In this example, the display token is used to specify desired counters (separated by commas):

report measurement-dqos-summary; display=DQOS_GATESET_ATTMP,DQOS_GATE_COMMIT;
Reply: Request was successful.
TIMESTAMP       20020310184428
DQOS_GATESET_ATTMP       10
DQOS_GATE_COMMIT          9

To manage the collection of DQoS measurements, use the following commands:

To display the current provisioning settings of DQoS measurements (enabled or disabled status), enter the following command:

show measurement-prov type=DQOS;

To change the current provisioning settings of DQoS measurements (enabled or disabled status) and/or the time interval (5, 15 [default], 30, or 60 minutes), enter the following command:

change measurement-prov type=dqos; enable=yes; time-interval=30;

Measurements for the DQoS Feature on COPS Interface

The system supports a number of measurements related to gate coordination over DQoS and PCMM interfaces. See the complete list of measurements in the "Traffic Measurements" chapter of the Cisco BTS 10200 Softswitch Operations and Maintenance Guide.

The Cisco BTS 10200 Softswitch tracks and reports measurements separately for each of the CMTS units (aggregation routers) and PS units it supports.

Measurements for the EM Feature

The system supports a number of measurements related to EMs. Use the following CLI command to retrieve these measurements:

report measurement-em-summary

A typical command and system response are shown below:


report measurement-em-summary

TIMESTAMP
CALL_AGENT_ID
CONDITION
BILLING_EM_ACKED 
BILLING_EM_LOGGED 
BILLING_EM_RETRANS
2003-07-10 16:15:00
CA146
Normal
2
3
3

See the complete list of measurements in the "Traffic Measurements" chapter of the Cisco BTS 10200 Softswitch Operations and Maintenance Guide.

Events and Alarms

This section lists the events and alarms applicable to the PacketCable implementation, including:

Events and Alarms Specific to PacketCable-Based Network Elements and PCMM Features

Events and Alarms for the EM Feature

Events and Alarms for the Security Interface Feature

This section lists only the events and alarms that are specific to the PacketCable-based implementation, and includes only the name and description of each alarm. The lists in this section are not exhaustive.
Detailed descriptions of all events and alarms, and recommended corrective actions, are presented in the Cisco BTS 10200 Softswitch Troubleshooting Guide.

Events and Alarms Specific to PacketCable-Based Network Elements and PCMM Features

The following events and alarms can be generated in response to processing problems or network connection issues with PacketCable-based network elements:

CALL PROCESSING Event #15—CMTS ER ID Not found in MGW table (INFO)

SIGNALING Alarm #103—AGGR Connection Down (MAJOR)

SIGNALING Event #104—AGGR Unable To Establish Connection (INFO)

SIGNALING Event #105—AGGR Gate Set Failed (INFO)

SIGNALING Alarm #155—PCMM Unsolicited Gate Delete (INFO)

Events and Alarms for the EM Feature

The following events and alarms can be generated by the EM feature.

BILLING Alarm #38—EM log file access error (MAJOR)

BILLING Alarm #39—RADIUS accounting receive failure (MINOR)

BILLING Alarm #40—EM encode failure (MINOR)

BILLING Alarm #41—Message content error (MINOR)

BILLING Event #42—Error reading provisioned data—using default (WARNING)

BILLING Event #44—RKS switch occurred (MAJOR)

BILLING Event #45—Event Message log file opened (MINOR)

BILLING Event #46—Event Message log file closed (MINOR)

BILLING Alarm #47—RKS unreachable for 1 hr (MINOR)

BILLING Alarm #48—RKS unreachable for 3 hours (MAJOR)

BILLING Alarm #49—RKS unreachable for 5 hours (CRITICAL)

BILLING Alarm #53—Event Message disk space 50 percent full (MINOR)

BILLING Alarm #54—Event Message disk space 70 percent full (MAJOR)

BILLING Alarm #55—Event Message disk space 100 percent full (CRITICAL)

Events and Alarms for the Security Interface Feature

The following events and alarms can be generated in response to PacketCable-related security signaling conditions:

SECURITY Alarm #3—IPsec connection down (MAJOR)

SECURITY Event #4—IPsec MTA Key Establish Error (WARNING)

SECURITY Event #5—IPsec outgoing SA not found (WARNING)

EM Generation Details and Content

This section describes the internal processes for EM generation and the content of the EMs. These processes are based on the PacketCable Event Message Specification PKT-SP-EM-I10-040721.


Note The system complies with the RKS EM billing interface requirements of PKT-SP-EM-I10-040721. For information on compliance with specific paragraphs of PacketCable standards, contact your Cisco account team.


EM Generation Details

Table 2 lists the EMs generated by call configuration.

Table 2 EMs Generated by Call Configuration 

Cisco BTS 10200 Softswitch Generates EMs for ...
Call Configuration
On-net to On-net
On-net to Off-net
Off-net to On-net

Originating CMS

X

X

 

Terminating CMS

X

 

X

Originating MGC

 

 

X

Terminating MGC

 

X

 


Table 3 lists the EMs that can be generated by the CMS and MGC.

Table 3 EMs Generated by Logical Entity 

Event Message
CMS
MGC

Signaling_Start

X

X

Signaling_Stop

X

X

Interconnect_Start

 

X

Interconnect_Stop

 

X

Call_Answer

X

X

Call_Disconnect

X

X

Database_Query

X

 

Service_Instance

X

 

Service_Activation

X

 

Service_Deactivation

X

 

Media_Alive

X

X

Time_Change

X

X


Table 4 lists the EMs for a call and the triggers that generate them (single zone scenario only) in the appropriate logical entities running in the Cisco BTS 10200 Softswitch (CMS and MGC).

Table 4 EM Triggers Grouped by Logical Entity 

Event Message
Originating CMS
Terminating CMS
Originating MGC
Terminating MGC

Signaling_Start

Timestamp: Receipt of NCS NTFY
Send: after translation

Internal system trigger (internal to the Cisco BTS 10200 Softswitch)

1. Receipt of IAM
or
2. TGCP NTFY

Receipt of Invite (internal system trigger)

Signaling_Stop

If T-CMS releases first: receipt of 250RSP to DLCX

If O-CMS releases first: before deallocating call block

If O-CMS releases first: receipt of 250RSP to DLCX

If T-CMS releases first: before deallocating call block

If T-MGC releases first: upon last of following events:

1. Receipt or transmission of RLC from/to SG

2. Receipt or transmission of Ack for TGCP DLCX

3. Receipt or transmission of last msg from/to T-CMS (internal system trigger)

If O-MGC releases first: before deallocating call block

Receipt of 250OK to DLCX

Interconnect_Start

 

 

Transmission or receipt of ACM

Transmission or receipt of ACM

Interconnect_Stop

 

 

Release of PSTN bandwidth

Release of PSTN bandwidth

Call_Answer

Receipt of 200OK to Invite with call answer

Receipt of NCS NTFY for off-hook of T-MTA

1. Receipt of ANM
or
2. Answer indication on operator service

1. Receipt of ANM
or
2. Answer indication on operator service

Call_Disconnect

Transmission of DLCX or delete connection on errors

Transmission of DLCX

1. Receipt of REL
or
2. Transmission of BYE for REL

1. Receipt of REL
or
2. Disconnect indication on operator service trunk disconnect

Database_Query

Receipt of response from DB or intelligent peripheral

Receipt of response from DB or intelligent peripheral

 —

 —

Service_Instance

Operation of service

Operation of service

 —

 —

Service_Activation

Successful activation

Successful activation

 —

 —

Service_Deactivation

Successful deactivation

Successful deactivation

 —

 —

Media_Alive

Periodic, based on provisioned parameters

Periodic, based on provisioned parameters

Periodic, based on provisioned parameters

Periodic, based on provisioned parameters

Time_Change

When time is adjusted

When time is adjusted

When time is adjusted

When time is adjusted


Table 5 lists the PacketCable 1.0 features, the EMs generated for them, and the event that triggers the message. Some of the triggering events include the logical entities—Originating CMS (O-CMS) and Terminating CMS (T-CMS)—running in the Cisco BTS 10200 Softswitch.

Table 5 PacketCable 1.0 Features and Associated EMs 

 
EMs Sent in Addition to Basic Call EMs
Comments
PacketCable 1.0 Feature
Event Message
Trigger

911 service—Similar to on-net to off-net call on a unique trunk group ID.

None

 —

 —

Other N11 services—Similar to above

None

 —

 —

Database Query

     

a. Send all database queries to PSTN
on special trunk

None

 —

 —

b. Query database and route accordingly

db_query

O-CMS on receipt of response to database dip.

Query types:

1 = Toll-free number lookup

2 = Local number portability (LNP) number lookup

3 = Calling name delivery lookup

If the query is successful—that is, if the query returns the calling party's name—the query type (1, 2, or 3) is included in the EM:

For types 1 and 2, the value in the EM Return_Number field contains the new called party digits.

For type 3, the value in the EM Return_Number field contains a valid string, such as "O" or "P". 1

If the query fails, no EM is sent.

Operator Service

     

a. 0- service (no digit after 0)

None

Called party number 0 is replaced by Operator Service Provider number.

Only call routing.

b. 0+ service (digits after 0, not needed in PacketCable 1.0)

 

 

Only call routing.

Call block service (with new call to announcement server)

Service instance

O-CMS and T-CMS decide to block call.

If announcement server is connected, event messages are generated for call with same BCID.

Call waiting

     

a. Announcement server on net

Service instance

O-CMS and T-CMS when call waiting is initiated. Second call BCID for service instance.

Only two calls, one active and one on hold, are required. Each half-call generates an EM. A half-call for an on-net announcement server for call waiting tone need not generate an EM. Here is an example of a call scenario:

A calls B, C calls A:
(A -> B, C -> A)
BCID1 for A(O), other leg BCID2
BCID2 for B(T), other leg BCID1
BCID3 for C(O), other leg BCID4
BCID4 for A(T), other leg BCID3

BCID4 for CW service instance, related BCID = BCID1

b. Announcement server on PSTN

Not supported

 —

Call forwarding

Service instance

CMS (O/T) when forwarded call leg is initiated.

A calls B, B forwards to C:
(A -> B -> C)
BCID1 for A(O), other leg BCID2
BCID2 for B(T), other leg BCID1
BCID3 for B(O), other leg BCID4
BCID4 for C(T), other leg BCID3
BCID3 for CFW service instance, related BCID=BCID2

Return call
(with caller ID privacy restriction)

     

a. Announcement server on net

Service instance

O-CMS on feature initiation.

Note CMS-CMS signaling is not supported in this release.

b. Announcement server on PSTN

Not supported

 —

 

Repeat call (*66)

   

CMS-CMS signaling is not supported in this release.

a. Announcement server on net

Service instance

Repeat call is initiated.

Separate BCID for service instance.

b. Announcement server on PSTN

Not supported

 —

 —

Voice mail (voice mail server on off-net)

None

 —

 —

Deposit and retrieval: similar to on-net to off-net call

None

 —

 —

Message waiting indicator

None

No event messages for message waiting.

Privacy indicator

Signaling start

Indicates whether the system populates field 12 of the EM with the calling party service (privacy setting) for the calling party.

This attribute uses the previously undefined field 12 in PKT-SP-EM-I10-040721.

See the "EM Content" section for additional requirements.

1 "O" = Name is out of area, unknown, or not available. "P" = Name presentation is restricted.


EM Content

The following EMs for a call contain the attributes listed, and are based on the four logical entities running in the Cisco BTS 10200 Softswitch: Originating CMS (O-CMS), Terminating CMS (T-CMS), Originating MGC (O-MGC), and Terminating MGC (T-MGC).

Signaling Start
Attribute
O-CMS
T-CMS
O-MGC (Off-net to On-net Call)
T-MGC (On-net to Off-net Call)
 

Direction indicator

X

X

X

X

 

MTA endpoint name

Originating

Terminating

Name of endpoint (EP) in MGW

Name of endpoint (EP) in MGW

 

Calling party number

X

X

X

X

 

Calling party service 1

X

X

X

X

 

Called party number

X

X

X

X

 

Routing number

X

X

X

X

 

Location routing number (LRN)

X

X

X

X

 

Carrier identification code (CIC)

 

 

X

X

 

Trunk group ID

 

 

X

X

 

Jurisdiction information parameter (JIP)

X

X

X

 
 

Ported-in calling number

X

     
 

Ported-in called number

 

X

   
 

Calling party NP source

X

     
 

Called party NP source

 

X

   
 

Billing type (measured rate or flat rate)

X

     
1 The calling party service attribute uses the previously undefined field 12 (see PKT-SP-EM-I10-040721). It is an unsigned integer, 4 bytes in length. If (a) the EM-PRIVACY-IND-SUPP token in the CA-CONFIG table is set to Y, and (b) the calling party number field in the EM is populated, then the system populates the calling party service field as follows: If the presentation status (PS) of the calling party is set to private, the calling party service field is set to 1; if the PS is set to public, the calling party service field is set to 0. If the EM-PRIVACY-IND-SUPP token is set to N (default), or if the calling party number is not present in the Signaling Start EM, or the PS is not present in the incoming message, the system does not populate the calling party service field.

Signaling Stop
Attribute
O-CMS
T-CMS
O-MGC (Off-net to On-net Call)
T-MGC (On-net to Off-net Call)
 

BCID of T-CMS or T-MGC

X

 

X

 

BCID of O-CMS or O-MGC

 

X

 

X

FEID of T-CMS or T-MGC

X

 

X

 

FEID of O-CMS or O-MGC

 

X

 

X


Interconnect Start
Attribute
O-CMS
T-CMS
O-MGC (Off-net to On-net Call)
T-MGC (On-net to Off-net Call)
 

Routing number

 

 

X

X

CIC

 

 

X

X

Trunk group ID

 

 

X

X


Interconnect Stop
Attribute
O-CMS
T-CMS
O-MGC (Off-net to On-net Call)
T-MGC (On-net to Off-net Call)
 

CIC

 

 

X

X

Trunk group ID

 

 

X

X


Call Answer
Attribute
O-CMS
T-CMS
O-MGC (Off-net to On-net Call)
T-MGC (On-net to Off-net Call)
 

Charge number

X

X

X

X

BCID of T-CMS or T-MGC

X

 

X

 

FEID of T-CMS or T-MGC

X

 

X

 

BCID of O-CMS or O-MGC

 

X

 

X

FEID of O-CMS or O-MGC

 

X

 

X


Call Disconnect
Attribute
O-CMS
T-CMS
O-MGC (Off-net to On-net Call)
T-MGC (On-net to Off-net Call)
 

Call termination cause

X

X

X

X


Service Instance
Attribute
O-CMS
T-CMS
O-MGC (Off-net to On-net Call)
T-MGC (On-net to Off-net Call)

 

Service name (plus specified attributes in the table below)

X

X

 

 

 

Account code

X

     
 

Authorization code

X

     


Note Only a limited number of service names are specified in the PacketCable 1.0 specification. The Cisco BTS 10200 Softswitch supports many other features; however, it does not send EMs for those features to a standard Record Keeping Server (RKS) because the feature codes for those features have not yet been defined by PacketCable.


Service- Specific Attributes
Attribute
Call Forward
Call Waiting
Repeat Call
Return Call
Call Block
Three- Way Call
Privacy Indicator
 

Related BCID

X

X

 

 

 

X

 

Charge number

X

X

X

X

 

X

 

1st call calling party number

 

X

 

 

 

   

2nd call calling party number

 

X

 

 

 

   

Called party number

 

X

 

 

 

   

Routing number

 

 

X

X

 

   

Calling party number

 

 

X

X

 

 

X

Calling party service

 

 

X

X

 

 

X

Termination cause

 

 

 

 

X

   

Service Activation
Attribute
O-CMS
T-CMS
O-MGC
(Off-net to On-net Call)
T-MGC
(On-net to Off-net Call)

 

Service name (plus specified attributes in the following table)

X

X

 

 


Service-Specific Attributes
Attribute
Call Forward
Call Waiting
Call Block
Customer Originated Trace
 

Charge number

X

X

X

X

Calling party number

X

X

X

X

Forwarded number

X

 

 

 

Service Deactivation
Attribute
O-CMS
T-CMS
O-MGC
(Off-net to On-net Call)
T-MGC
(On-net to Off-net Call)

 

Service name (plus specified attributes in the table below)

X

X

 

 


Service-Specific Attributes
Attribute
Call Forward
Call Waiting
Call Block
 

Charge number

X

X

X

Calling party number

X

X

X


Database Query
Attribute
O-CMS
T-CMS
O-MGC
(Off-net to On-net Call)
T-MGC
(On-net to Off-net Call)
 

Database ID

X

X

 

 

Query type

X

X

 

 

Called party number

X

X

 

 

Returned number

X

X

 

 


Activity
Attribute
O-CMS
T-CMS
O-MGC
(Off-net to On-net Call)
T-MGC
(On-net to Off-net Call)
 

Media alive

X

X

X

X


Time Change
Attribute
O-CMS
T-CMS
O-MGC
(Off-net to On-net Call)
T-MGC
(On-net to Off-net Call)
 

Time adjustment

X

X

X

X


References

Industry Standards

Standards
Title

IETF RFC 2748

The COPS (Common Open Policy Service) Protocol, January 2000

PKT-SP-CODEC-I04-021018

PacketCable Audio/Video Codecs Specification, October 18, 2002

PKT-SP-DQOS-I07-030815

PacketCable Dynamic Quality of Service Specification, August 15, 2003

PKT-SP-MGCP-I08-030728

PacketCable Network-Based Call Signaling Protocol Specification, July 28, 2003

PKT-SP-TGCP-I05-030728

PacketCable PSTN Gateway Call Signaling Protocol Specification, July 28, 2003

PKT-SP-EM-I10-040721

Note Compliant with the RKS EM billing interface requirements of PKT-SP-EM-I10-040721.

PacketCable Event Message Specification, July 21, 2004

EM-N-04.0186-3

Note Compliant with the file-naming convention in EM-N-04.0186-3.

CableLabs Engineering Change (EC) Form

PKT-SP-SEC-I09-030728

PacketCable Security Specification, July 28, 2003

PKT-SP-ESP-I01-991229

PacketCable Electronic Surveillance Specification, December 29, 1999

PKT-SP-MM-I02-040930

PacketCable Multimedia Specification, September 30, 2004



Note For information on compliance with specific paragraphs of PacketCable standards and ECNs, contact your Cisco account team.