Command Reference Guide for Cisco MXE-OS Release 1.3
Media Processing Command Reference
Downloads: This chapterpdf (PDF - 722.0KB) The complete bookPDF (PDF - 6.69MB) | Feedback

Media Processing Command Reference

Table Of Contents

Media Processing Command Reference

action

application accessNumber

application scheduledResources

application totalResources

application-profile (dial-peer media-service)

application-profile (media service media-processing)

app-mux

attribute h264

bandwidth (stream profile)

calling-party-info

clear ctsman statistics

codec-profile (media service media-processing)

codec-profile (stream profile)

codec-type

ctsman enable

ctsman hostname

ctsman ip

ctsman leg-limit

ctsman password

ctsman port

ctsman server-port

ctsman ssl-hostname-check

ctsman username

custom

default-telepresence-media-prof

default-vc-media-profile

description (dial-peer media-service)

destination-pattern

dial-peer media-service

level-idc

listen-port

max-fs

max-mbps

max-trans-bandwidth (media-profile)

max-trans-bandwidth (stream-profile)

media-profile (dial-peer media-service)

media-profile (media service media-processing)

media service media-processing

mode

packetization-mode

packet-time

payload-number

preference

quality (stream-profile)

resolution-profile (media service media-processing)

session-bandwidth (media profile)

session-protocol (dial-peer media-service)

session-target (dial-peer media-service)

show application

show call-detail

show call-summary

show ctsman conference

show ctsman config

show ctsman statistics

show dial-peer media-service

show media-processing

show media-statistics

shutdown (interface)

shutdown (sip)

sip

stream-profile (media profile)

stream-profile (media service stream-processing)

stream-type

transport


Media Processing Command Reference


Revised: September 2011

This chapter includes the Cisco MXE-OS commands used for configuring media-processing features.

action

To configure how an application-profile responds to calls, use the action command. To remove this configuration use the no form of this command.

action {query}

no action {query}

Syntax Description

query

Specifies that the application determines what to do with the call.


Defaults

Query

Command Modes

Application profile

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

None

Examples

This example shows how to configure application-profile 1's call response action:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# application-profile 1
mxe(config-media-serv-application-pro)# action query

Related Commands

Command
Description

application-profile (media service media-processing)

Creates or modifies an application profile.

media service media-processing

Enter the media service media-processing mode.

show media-processing

Displays media-processing profiles.


application accessNumber

To configure the access number or trunk that Cisco MXE-OS uses to receive calls, use the application accessNumber command.

application accessNumber number

Syntax Description

number

Specifies the access number that Cisco MXE-OS uses to receive scheduled video interoperability calls. Typically, this is the number that the CTS Manager uses to route calls to the Cisco MXE-OS device.

Maximum size is 80 characters.



Note Although visible in the command-line help strings, the directive keyword is not supported.


Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin

Command History

Release
Modification

1.1

This command was introduced.


Usage Guidelines

None

Examples

This example shows how to configure 11055 as the access number used by Cisco MXE-OS to receive calls from videoconferencing endpoints:

mxe# configure terminal
mxe(config)# application accessNumber 11055
 
   

Related Commands

Command
Description

application scheduledResources

Configures the number of allocated Cisco MXE-OS resources for scheduled calls.

show application

Displays the Cisco MXE-OS device resource allocation configuration.


application scheduledResources

To configure the number of resources that are allocated for scheduled calls, use the application scheduledResources command.

application scheduledResources number

Syntax Description

number

Specifies the number of resources that Cisco MXE-OS allocates for scheduled calls for an application server, such as the Cisco TelePresence System Manager. Range varies by the number of installed port licenses.



Note Although visible in the command-line help strings, the directive keyword is not supported.


Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin

Command History

Release
Modification

1.1

This command was introduced.


Usage Guidelines

Cisco MXE-OS enforces resource limits regardless of port availability. Before configuring, you should confirm the requirements for scheduled resources.

Examples

This example shows how to configure a maximum of 15 resources for scheduled calls:

mxe# configure terminal
mxe(config)# application scheduledResources 15
 
   

Related Commands

Command
Description

application accessNumber

Configures the Cisco MXE-OS access number or trunk.

ctsman leg-limit

Configures the Cisco MXE-OS device resource allocations.

show application

Displays the Cisco MXE-OS device resource allocation configuration.


application totalResources

To configure the maximum number of resources that the Cisco MXE-OS allocates for media-processing features, use the application totalResources command for devices running Cisco MXE-OS Release 1.1. This command was deprecated in Cisco MXE-OS Release 1.1.1.

application totalResources number

Syntax Description

number

Specifies the number of resources that Cisco MXE-OS allocates for media-processing features, such as mxe-interop. Range varies by the number of installed port licenses.


Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin

Command History

Release
Modification

1.1

This command was introduced.

1.1.1

This command was deprecated.


Usage Guidelines

Cisco MXE-OS supports scheduled and ad-hoc calls. You can allocate the Cisco MXE-OS resources to manage the maximum number of scheduled and ad-hoc calls.

To allow only scheduled calls, set the same value for these commands: application totalResources, application scheduledResources, and ctsman leg-limit.

To allow ad-hoc calls, lower the application scheduledResources and the ctsman leg-limit values by an amount equal to the resources required to fulfill these calls. Typically by two resources per participant when not using WebEx, and one extra resource when using WebEx.

You can adjust the resources based on the requirement. If the Cisco MXE-OS is not used for any scheduled calls, set the application scheduledResources and the ctsman leg-limit values to zero.

If you find that a Cisco MXE-OS has underutilized scheduled call capacity, you can dynamically lower the leg-limit value and reregister with the CTS Manager. To do this, change the ctsman leg-limit value and then execute the no ctsman enable and the ctsman enable commands. Next, change the application scheduledResources to a lower value to add more ad-hoc call capacity.

The application totalResources command defines the total number of Cisco MXE-OS resources. The resources are defined as number of ports, similar to licensing ports. The total capacity is 30 ports. This value cannot exceed the port license count. If a you specify a higher value, the port license count is used as the application totalResources value.

For Cisco MXE-OS Release 1.1 we recommend specifying an even number of resources for all application resource values.

Examples

This example shows how to configure a total of 30 resources for media-processing features:

mxe# configure terminal
mxe(config)# application totalResources 30
 
   

Related Commands

Command
Description

application accessNumber

Configures the Cisco MXE-OS access number or trunk.

application scheduledResources

Configures the number of allocated Cisco MXE-OS resources for scheduled calls.

ctsman leg-limit

Configures the Cisco MXE-OS device resource allocations.

show application

Displays the Cisco MXE-OS device resource allocation configuration.


application-profile (dial-peer media-service)

To associate an application-profile with a dial peer, use the application-profile command. To remove an application profile, use the no form of this command.

application-profile {profile-id}

no application-profile

Syntax Description

profile-id

Use a profile-id created with the application-profile (media service media-processing) command.


Defaults

None

Command Modes

Dial-peer media-service

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

For information about application profiles, see the Configuration Guide for Cisco MXE-OS.

Examples

This example shows how to associate an application profile with a dial peer.

mxe# configure terminal
mxe(config)# dial-peer media-service 1
mxe(config-dial-peer)# application-profile 1

Related Commands

Command
Description

application-profile (media service media-processing)

Creates or modifies an application profile.

show media-processing

Displays media-processing profiles.


application-profile (media service media-processing)

To create or modify an application profile and enter the application-profile configuration mode, use the application-profile command. To remove an application profile, use the no form of this command.

application-profile {profile-id}

no application-profile

Syntax Description

profile-id

Unique identifier. Up to 80 alphanumeric characters are allowed.


Defaults

None

Command Modes

Media service media-processing

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

For information about application profiles, see the Configuration Guide for Cisco MXE-OS.

Examples

This example shows how to create an application profile:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# application-profile 1
mxe(config-media-serv-application-pro)# 

Related Commands

Command
Description

application-profile (dial-peer media-service)

Associates an application profile with a dial peer.

show media-processing

Displays media-processing profiles.


app-mux

To enable app-mux protocol support for a stream profile, use the app-mux command. To remove this configuration, use the no form of this command.

app-mux

no app-mux

Syntax Description

This command has no keywords or arguments.

Defaults

Disabled

Command Modes

Stream profile

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

A stream profile must first be created with the stream-profile (media service stream-processing) command.

Examples

This example shows how to enable app-mux protocol support for stream-profile 1:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# stream-profile 1
mxe(config-media-serv-stream-profile)# app-mux

Related Commands

Command
Description

show media-processing

Displays media-processing profiles.

stream-profile (media service stream-processing)

Creates or modifies a stream profile and enters the stream-profile mode.


attribute h264

To configure a codec profile as H.264 and enter the codec-profile attribute H.264 configuration mode, use the attribute h264 command. To remove attributes, use the no form of this command.

attribute h264

Syntax Description

None

Defaults

None

Command Modes

Codec profile

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

A codec profile must first be created with the codec-profile (media service media-processing) command.

Examples

This example shows how to configure H.264 attributes for codec profile 1 and enter the codec-profit attribute H.264 configuration mode:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# codec-profile 1
mxe(config-media-serv-codec-profile)# attribute h264
mxe(config-media-serv-codec-profile-attr-h264)# 

Related Commands

Command
Description

codec-profile (media service media-processing)

Creates and modifies codec profiles.

show media-processing

Displays media-processing profiles.


bandwidth (stream profile)

To configure the amount of bandwidth used by media in a stream profile, use the bandwidth command. To remove the configuration, use the no form of this command.

bandwidth {value}

no bandwidth {value}

Syntax Description

value

Bandwidth in bits per second (b/s). The range is from 64000 to 32000000 b/s.


Defaults

128000 b/s (audio default)

Command Modes

Stream profile configuration

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

A stream profile must first be created with the stream-profile (media service stream-processing) command.

Examples

This example shows how to configure a bandwidth of 64000 b/s for stream profile 1:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# stream-profile 1
mxe(config-media-serv-stream-profile)# bandwidth 64000

Related Commands

Command
Description

show media-processing

Displays media-processing profiles.

stream-profile (media service stream-processing)

Creates or modifies a stream profile and enters the stream-profile mode.


calling-party-info

To configure the pattern for which a media-service dial-peer will match inbound dial peers, use the calling-party-info command. To remove a defined pattern, use the no form of this command.

calling-party-info {id | name} inbound-match-pattern

no calling-party-info {id | name} inbound-match-pattern

Syntax Description

id

Specifies that the dial peer uses caller ID as a matching key pattern.

name

Specifies that the dial peer uses the display name of the endpoint as a matching key pattern.

inbound-match-pattern

Perl-compatible regular expression (PCRE). Up to 80 characters are allowed.


Defaults

None

Command Modes

Dial-peer media service

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

The name keyword matches the user portion of the Session Initiation Protocol (SIP) Uniform Resource Identifier (URI) of the Remote-Party-ID Header and the From Header.

The inbound-match-pattern argument is in the form of a regular expression against which the value of the corresponding header field is matched.

Before using this command, you must first create a media-service dial peer with the dial-peer media-service command.

Examples

This example shows how to define calling party information:

mxe# configure terminal
mxe(config)# dial-peer media-service 2
mxe(config-dial-peer)# calling-party-info id ^10

Related Commands

Command
Description

show dial-peer media-service

Displays information for one or all media-service dial peers.


clear ctsman statistics

To clear Cisco Telepresence Manager (CTS Manager) statistics, use the clear ctsman statistics command.

clear ctsman statistics

Syntax Description

This command has no keywords or arguments.

Defaults

None

Command Modes

EXEC

Supported User Roles

network-admin
network-operator

Command History

Release
Modification

1.1

This command was introduced.


Usage Guidelines

None

Examples

The following example shows how to clear CTS Manager statistics:

mxe# clear ctsman statistics

codec-profile (media service media-processing)

To create or modify a codec profile, use the codec-profile command. To remove a codec profile, use the no form of this command.

codec-profile {profile-id}

no codec-profile {profile-id}

Syntax Description

profile-id

Unique identifier for the codec profile. The valid range is from 1 to 65535.


Defaults

None

Command Modes

Media service media-processing

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

None

Examples

This example shows how to configure a codec-profile:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# codec-profile 1

Related Commands

Command
Description

show media-processing

Displays media-processing profiles.

codec-profile (stream profile)

Applies a codec profile to a stream profile.


codec-profile (stream profile)

To apply a codec profile to a stream-profile, use the codec-profile command. To remove a codec profile, use the no form of this command.

codec-profile {profile-id} [preference value]

no codec-profile {profile-id}

Syntax Description

profile-id

The ID of a codec-profile configured with the codec-profile (media-service) command.

preference

(Optional) Specifies the order of the codecs when multiple codec-profiles are applied to a stream-profile.

value

(Optional) The value range is from 1 to 10.


Defaults

10

Command Modes

Stream profile

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

A codec profile must first be configured with the codec-profile (media service media-processing) command.

For information about codec profiles, see the Configuration Guide for Cisco MXE-OS.

Examples

This example shows how to configure stream profile 1 with codec profiles 1 and 2 and their preference orders:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# stream-profile 1
mxe(config-media-serv-stream-profile)# codec-profile 1 preference 1
mxe(config-media-serv-stream-profile)# codec-profile 2 preference 2

Related Commands

Command
Description

show media-processing

Displays media-processing profiles.

codec-profile (media service media-processing)

Creates a codec profile.


codec-type

To specify the type of codec to be used for a codec profile, use the codec-type command. To remove the codec type configuration, use the no form of this command.

codec-type {aac | g711-ulaw | g711-alaw | g722 | h264}

no codec-type {aac | g711-ulaw | g711-alaw | g722 | h264}

Syntax Description

aac

Specifies the AAC codec.

g711-ulaw

Specifies the G.711 µ-law codec.

g711-alaw

Specifies the G.711 a-law codec.

g722

Specifies the G.722 codec.

h264

Specifies the H.264 codec.


Defaults

None

Command Modes

Codec profile

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

A codec profile must first be configured with the codec-profile (media service media-processing) command.

Examples

This example shows how to specify a codec type for codec profile 1:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# codec-profile 1
mxe(config-media-serv-codec-profile)# codec-type h264

Related Commands

Command
Description

codec-profile (media service media-processing)

Creates a codec profile.


ctsman enable

To enable Cisco MXE-OS communications with a Cisco Telepresence Manager (CTS Manager), use the ctsman enable command. To disable communications with the CTS Manager, use the no form of this command. This command was deprecated in Cisco MXE-OS Release 1.2.

ctsman enable

no ctsman enable

Syntax Description

This command has no keywords or arguments

Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin

Command History

Release
Modification

1.1

This command was introduced.

1.2

This command was deprecated.


Usage Guidelines

If you execute the no ctsman enable command, even though the active HTTP/SOAP communications are disabled, you can continue configuring ctsman related parameters.

Examples

The following shows how to enable communications with a CTS Manager:

mxe# configure terminal
mxe(config) ctsman enable

Related Commands

Command
Description

show ctsman config

Displays the CTS Manager configuration information.


ctsman hostname

To enable or disable Cisco Telepresence Manager (CTS Manager) OpenSSL hostname checking, use the ctsman hostname command for devices running Cisco MXE-OS Release 1.1.

This command was deprecated in Cisco MXE-OS Release 1.2. See the ctsman ssl-hostname-check command.

ctsman hostname {enable | disable}

Syntax Description

enable

Enables CTS Manager OpenSSL hostname checking.

disable

Disables CTS Manager OpenSSL hostname checking.


Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin

Command History

Release
Modification

1.1

This command was introduced.

1.2

This command was deprecated.


Usage Guidelines

Cisco MXE-OS validates the hostname against the security certificate of the CTS Manager during secured communications. The ctsman hostname command is active only when the ctsman server-port is 443 or 8443.

Examples

The following example shows how to enable CTS Manager OpenSSL hostname checking:

mxe# configure terminal
mxe(config)# ctsman hostname enable
 
   

Related Commands

Command
Description

ctsman server-port

Configures the Cisco MXE-OS port number.


ctsman ip

To configure the IP address and port number of the Cisco Telepresence Manager (CTS Manager), use the ctsman ip command. To remove the configuration, use the no form of this command.

ctsman ip ipv4-address port-number

no ctsman ip ipv4-address port-number

Syntax Description

ipv4-address

Specify the IPv4 address of the CTS Manager. Use the A.B.C.D format.

port-number

Specify the port number used by the CTS Manager registration requests. The port-number is a TCP/IP port number. The range is 1 to 65535.


Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin

Command History

Release
Modification

1.1

This command was introduced.

1.2

The port-number value was added.


Usage Guidelines

None

Examples

The following example shows how to configure the CTS Manager IPv4 address and port number:

mxe# configure terminal
mxe(config) ctsman ip 10.1.1.1 80

Related Commands

Command
Description

ctsman password

Configures the password for CTS Manager communications.

ctsman username

Configures the username for CTS Manager communications.


ctsman leg-limit

To configure the maximum number of Cisco MXE-OS device resources that the Cisco Telepresence Manager (CTS Manager) allocates for scheduled calls, use the ctsman leg-limit command. To return to the default setting, use the no form of this command.

ctsman leg-limit value

no ctsman leg-limit value

Syntax Description

value

Specifies the maximum number of Cisco MXE-OS device resources.


Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin

Command History

Release
Modification

1.1

This command was introduced.


Usage Guidelines

The leg-limit value represents the maximum number of Cisco MXE-OS device resources that the CTS Manager can allocate for scheduled calls. The value should be less than or equal to the number of installed port licenses.

The leg-limit value cannot exceed the number of scheduled resources that are specified by using the application scheduledResources command.

Examples

The following example shows how to configure 20 as the maximum number of Cisco MXE-OS device resources that the CTS Manager allocates for scheduled calls:

mxe# configure terminal
mxe(config) ctsman leg-limit 20

Related Commands

Command
Description

application scheduledResources

Configures the number of resources that are allocated for scheduled calls


ctsman password

To configure the password for Cisco Telepresence Manager (CTS Manager) communication, use the ctsman password command. To remove the password, use the no form of this command.

ctsman password password

no ctsman password

Syntax Description

password

Specifies the password that the Cisco MXE-OS uses for communication with the CTS Manager. Up to 80 characters are allowed.


Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin

Command History

Release
Modification

1.1

This command was introduced.


Usage Guidelines

The password must match the CTS Manager password defined in the CTS Manager Bridge configuration dialog window. The password displays as clear text.

Examples

The following example shows how to configure a CTS Manager password:

mxe# configure terminal
mxe(config) ctsman password admin1pw

Related Commands

Command
Description

ctsman username

Configures the username for CTS Manager communications.


ctsman port

To configure the Cisco Telepresence Manager (CTS Manager) port for incoming Simple Object Access Protocol (SOAP) messages from the Cisco MXE-OS device, use the ctsman port command for devices running Cisco MXE-OS Release 1.1. To remove the configuration, use the no form of this command.

This command was deprecated in Cisco MXE-OS Release 1.2.

ctsman port port-number

no ctsman port

Syntax Description

port-number

Specifies the CTS Manager port for incoming SOAP messages from the Cisco MXE-OS device. The range is from 1 to 65535.


Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin

Command History

Release
Modification

1.1

This command was introduced.

1.2

This command was deprecated.


Usage Guidelines

None

Examples

The following example shows how to configure the CTS Manager port to 80:

mxe# configure terminal
mxe(config) ctsman port 80

Related Commands

Command
Description

ctsman ip

Configures the CTS Manager IP address.


ctsman server-port

To configure the Cisco MXE-OS device port for incoming Simple Object Access Protocol (SOAP) messages from the Cisco Telepresence Manager (CTS Manager), use the ctsman server-port command. To remove the current configuration, use the no form of this command.

ctsman server-port port-number

no ctsman server-port

Syntax Description

port-number

The Cisco MXE-OS port number for incoming SOAP messages from the CTS Manager. The range is 1 to 65535.


Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin

Command History

Release
Modification

1.1

This command was introduced.


Usage Guidelines

If you enter a value of 443 or 8443, OpenSSL is used for communications.

Examples

The following example shows how to configure the Cisco MXE-OS server port to 8443:

mxe# configure terminal
mxe(config) ctsman server-port 8443

Related Commands

Command
Description

ctsman ssl-hostname-check

Enables or disables CTS Manager OpenSSL hostname checking


ctsman ssl-hostname-check

To enable or disable Cisco Telepresence Manager (CTS Manager) OpenSSL hostname checking, use the ctsman ssl-hostname-check command.

ctsman ssl-hostname-check {enable | disable}

Syntax Description

enable

Enables CTS Manager OpenSSL hostname checking.

disable

Disables CTS Manager OpenSSL hostname checking.


Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin

Command History

Release
Modification

1.2

This command was introduced.


Usage Guidelines

The ctsman ssl-hostname-check command controls how the OpenSSL implementation manages hostname checking during secure communications initialization. When the command is enabled, the Cisco MXE-OS validates the X.509 commonName and systemAltName portions of the certificates used by the CTS Manager for authentication and encryption.

If the ctsman server-port port-number is not 443 or 8443, the parameter value is ignored.

Examples

The following example shows how to enable CTS Manager OpenSSL hostname checking:

mxe# configure terminal
mxe(config)# ctsman ssl-hostname-check enable
 
   

Related Commands

Command
Description

ctsman server-port

Configures the Cisco MXE-OS port number.


ctsman username

To configure the username that Cisco MXE-OS uses for Cisco Telepresence Manager (CTS Manager) communication, use the ctsman username command. To remove the username, use the no form of this command.

ctsman username username

no ctsman username username

Syntax Description

username

CTS Manager username. Up to 80 characters are allowed.


Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin

Command History

Release
Modification

1.1

This command was introduced.


Usage Guidelines

The username must match the CTS Manager username defined in the CTS Manager Bridge configuration dialog window. The username is clear text.

Examples

The following example shows how to configure a CTS Manager username:

mxe# configure terminal
mxe(config) ctsman username admin1

Related Commands

Command
Description

ctsman password

Configures the password for CTS Manager communications.


custom

To configure a custom name and value for an H.264 attribute, use the custom command. To remove this configuration, use the no form of this command.

custom name [value]

no custom name [value]

Syntax Description

name

Up to 80 characters are allowed.

value

Up to 80 characters are allowed.


Defaults

None

Command Modes

Codec-profile attribute H.264

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

A codec profile must first be configured with the codec-profile (media service media-processing) command.

Examples

This example shows how to configure a custom attribute:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# codec-profile 1
mxe(config-media-serv-codec-profile)# attribute h264
mxe(config-media-serv-codec-profile-attr-h264)# custom level-asymmetry-allowed value 1

Related Commands

Command
Description

application accessNumber

Configure a codec-profile as H.264 and enters the codec-profile attribute H.264 configuration mode.

codec-profile (media service media-processing)

Creates a codec profile.


default-telepresence-media-prof

To configure a default media profile for an application profile to use for outbound dial-peers when TelePresence media capabilities are required, use the default-telepresence-media-prof command. To remove a default media profile, use the no form of this command.

default-telepresence-media-prof profile-id

no default-telepresence-media-prof profile-id

Syntax Description

profile-id

Profile ID of a media-profile created with the media-profile (media service media-processing) command.


Defaults

None

Command Modes

Application profile

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

Before using this command, you must first create an application profile with the application-profile (media service media-processing) command and a media profile with the media-profile (media service media-processing) command.

Examples

This example shows how to configure application profile 1 with media profile 1 as the default:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# application-profile 1
mxe(config-media-serv-application-pro)# default-telepresence-media-prof 1

Related Commands

Command
Description

application-profile (media service media-processing)

Create an application profile and enters the application-profile configuration mode.

Creates a media-profile.

show media-processing

Displays media-processing profiles.


default-vc-media-profile

To configure a default media profile for an application-profile to use for outbound dial-peers when videoconferencing media capabilities are required, use the default-vc-media-profile command. To remove a default media profile, use the no form of this command.

default-telepresence-media-profile {profile-id}

no default-telepresence-media-profile {profile-id}

Syntax Description

profile-id

Profile ID of a media-profile created with the media-profile (media service media-processing) command.


Defaults

Query

Command Modes

Application profile

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

Before using this command, you must first create an application profile with the application-profile (media service media-processing) command and a media profile with the media-profile (media service media-processing) command.

Examples

This example shows how to configure application-profile 1 with a default media-profile 1:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# application-profile 1
mxe(config-media-serv-application-pro)# default-vc-media-profile 1

Related Commands

Command
Description

application-profile (media service media-processing)

Create an application profile and enters the application-profile configuration mode.

Creates a media-profile.

show media-processing

Displays media-processing profiles.


description (dial-peer media-service)

To add a description to a dial peer, use the description command. To remove the description, use the no form of this command.

description {description}

no description

Syntax Description

description

Text string up to 80 alphanumeric characters.


Defaults

None

Command Modes

Dial-peer media-service

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

Before using this command, you must first create a media-service dial peer with the dial-peer media-service command.

Examples

This example shows how to configure a description for a dial peer 1:

mxe# configure terminal
mxe(config)# dial-peer media-service 1
mxe(config-dial-peer)# description Cisco TelePresence Endpoint

Related Commands

Command
Description

dial-peer media-service

Create a dial peer and enters the dial-peer media-service configuration mode.

show dial-peer media-service

Displays configuration information for one or all media-service dial peers.


destination-pattern

To configure the pattern that a dial peer uses for outbound dial-peer matching, use the destination-pattern command. To remove a destination pattern, use the no form of this command.

destination-pattern outbound-match-pattern

no destination-pattern outbound-match-pattern

Syntax Description

outbound-match-pattern

Perl-compatible regular expression (PCRE). Up to 80 characters are allowed.


Defaults

None

Command Modes

Dial-peer media-service

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

This command specifies the value in the user portion of the Request Uniform Resource Identifier (URI) header used to match the dial peer.

The outbound-match-pattern argument is in the form of a regular expression against which the value of the Request URI is matched.

Before using this command, you must first create a media-service dial peer with the dial-peer media-service command.

Examples

This example shows how to create a destination pattern for media-service dial peer 1:

mxe# configure terminal
mxe(config)# dial-peer media-service 1
mxe(config-dial-peer)# destination-pattern ^((1011)|(1017))

Related Commands

Command
Description

dial-peer media-service

Creates a dial peer and enters the dial peer media service configuration mode.

show dial-peer media-service

Displays information for one or all media-service dial peers.


dial-peer media-service

To create a media-service dial peer and enter the dial-peer configuration mode, use the dial-peer media-service command. To remove a defined dial peer, use the no form of this command.

dial-peer media-service dial-peer-id

no dial-peer media-service dial-peer-id

Syntax Description

dial-peer-id

Unique identifier. The range is from 1 to 65535.


Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

None

Examples

This example shows how to define dial peer 1:

mxe# configure terminal
mxe(config)# dial-peer media-service 1
mxe(config-dial-peer)#

Related Commands

Command
Description

show dial-peer media-service

Displays configuration information for one or all media-service dial peers.


level-idc

To specify a profile level for an H.264 attribute, use the level-idc command. To remove this configuration, use the no form of this command.

level-idc profile-level

no level-idc profile-level

Syntax Description

profile-level

A value ranging from 10 to 40.


Defaults

31

Command Modes

Codec-profile attribute H.264

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

A codec profile must first be configured with the codec-profile (media service media-processing) command.

Examples

This example shows how to configure an H.264 attribute profile level of 10 for codec-profile 1:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# codec-profile 1
mxe(config-media-serv-codec-profile)# attribute h264
mxe(config-media-serv-codec-profile-attr-h264)# level-idc 10

Related Commands

Command
Description

codec-profile (media service media-processing)

Creates a codec profile.

show media-processing

Displays media-processing profiles.


listen-port

To assign the listen port for Session Initiation Protocol (SIP) communications through Transit Control Protocol (TCP), use the listen-port command. To remove the listen port, use the no form of this command.

listen-port {non-secure port-number}

no listen-port {non-secure port-number}

Syntax Description

non-secure

Configures a non-secure port.

port-number

Port number. The range from 1024 to 65535.


Defaults

The default port number is 5060 for non-secure communications.

Command Modes

Media service SIP

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

None

Examples

This example shows how to configure the listen port for SIP communications:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# sip
mxe(config-media-serv-sip)# listen-port non-secure 5060

max-fs

To specify the maximum frame size of an H.264 attribute, use the max-fs command. To remove this configuration, use the no form of this command.

max-fs frame-size

no max-fs frame-size

Syntax Description

frame-size

Maximum frame size in macroblocks, ranging from 99 to 8192.


s

Defaults

3600

Command Modes

Codec-profile attribute H.264

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

A codec profile must first be configured with the codec-profile (media service media-processing) command.

Examples

This example shows how to configure the maximum frame size of 998 for codec profile 1:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# codec-profile 1
mxe(config-media-serv-codec-profile)# attribute h264
mxe(config-media-serv-codec-profile-attr-h264)# max-fs 998

Related Commands

Command
Description

codec-profile (media service media-processing)

Creates a codec profile.

show media-processing

Displays media-processing profiles.


max-mbps

To configure the maximum number of macroblocks per second (mbps) of an H.264 attribute, use the max-mbps command. To remove this configuration, use the no form of this command.

max-mbps value

no max-mbps value

Syntax Description

value

Maximum number of macroblocks per second, ranging from 1485 to 245760.


Defaults

108000

Command Modes

Codec-profile attribute H.264

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

Before using this command, a codec profile must first be configured with the codec-profile (media service media-processing) command.

Examples

This example shows how to configure a maximum of 245760 macroblocks per second for codec profile 1:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# codec-profile 1
mxe(config-media-serv-codec-profile)# attribute h264
mxe(config-media-serv-codec-profile-attr-h264)# max-mbps 245760

Related Commands

Command
Description

codec-profile (media service media-processing)

Creates a codec profile.

show media-processing

Displays media-processing profiles.


max-trans-bandwidth (media-profile)

To configure the maximum transmit bandwidth within a media profile, use the max-trans-bandwidth (media-profile) command. To remove the configuration, use the no form of this command.

max-trans-bandwidth value

no max-trans-bandwidth value

Syntax Description

value

Specifies the maximum transmit bandwidth available for the media session. The range is 0 to 32000000 b/s.


Defaults

None

Command Modes

Media profile configuration

Supported User Roles

network-admin

Command History

Release
Modification

1.3

This command was introduced.


Usage Guidelines

A media profile must first be created by using the media-profile (media service media-processing) command.

The max-trans-banwidth command controls the maximum bandwidth used for all the media streams (represented by stream profiles ) within the media profile.

The effective trasmit bandwidth is the lower value of the configured value and negotiated bandwidth. If the maximum transmit bandwidth is not configured, the negotiated session bandwidth is used.

Examples

This example shows how to configure a maximum of 32000000 b/s for media profile 1:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# media-profile 1
mxe(config-media-serv-media-profile)# max-trans-bandwidth 32000000
 
   

Related Commands

Command
Description

max-trans-bandwidth (stream-profile)

Configures the maximum transmit bandwidth within a stream profile.

media-profile (media service media-processing)

Creates a media profile.

quality (stream-profile)

Configures the quality preference for a stream profile.

resolution-profile (media service media-processing)

Creates or modifies a resolution profile.

show media-processing

Displays media-processing profiles.


max-trans-bandwidth (stream-profile)

To configure the maximum transmit bandwidth within a stream profile, use the max-trans-bandwidth command. To remove the configuration, use the no form of this command.

max-trans-bandwidth value

no max-trans-bandwidth value

Syntax Description

value

Specifies the maximum transmit bandwidth available for the stream profile. The range is 0 to 32000000 b/s.


Defaults

None

Command Modes

Media service stream-processing

Supported User Roles

network-admin

Command History

Release
Modification

1.3

This command was introduced.


Usage Guidelines

A stream profile must first be created by using the stream-profile (media service stream-processing) command.

The max-trans-bandwidth command at the stream-profile level controls the maximum bandwidth used for encoding the individual stream.

The effective bandwidth used is the lower value of the configured value and the negotiated value in the Session Description Protocol (SDP). If the maximum transmit bandwidth is not configured, the negotiated stream bandwidth is used.

Examples

This example shows how to configure a maximum of 32000000 b/s for stream profile 1:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# stream-profile 1
mxe(config-media-serv-stream-profile)# max-trans-bandwidth 32000000
 
   

Related Commands

Command
Description

max-trans-bandwidth (media-profile)

Configures the maximum transmit bandwidth within a media profile.

media-profile (media service media-processing)

Creates a media profile.

quality (stream-profile)

Configures the quality preference for a stream profile.

resolution-profile (media service media-processing)

Creates or modifies a resolution profile.

stream-profile (media service stream-processing)

Creates a stream profile.

show media-processing

Displays media-processing profiles.


media-profile (dial-peer media-service)

To apply a media profile to a dial peer, use the media-profile command. To remove a media-profile, use the no form of this command.

media-profile {profile-id}

no media-profile {profile-id}

Syntax Description

profile-id

A profile ID configured with the media-profile (media service media-processing) command.


Defaults

None

Command Modes

Dial-peer media-service

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

Before using this command, a media profile must first be configured with the media-profile (media service media-processing) command.

For information about media profiles, see the Configuration Guide for Cisco MXE-OS.

Examples

This example shows apply media-profile 1 to dial-peer 1:

mxe# configure terminal
mxe(config)# dial-peer media-service 1
mxe(config-dial-peer)# media-profile 1

Related Commands

Command
Description

media-profile (media service media-processing)

Creates or modifies a media profile.

show media-processing

Displays media-processing profiles.


media-profile (media service media-processing)

To create or modify a media profile and enter the media-profile configuration mode, use the media-profile command. To remove a media-profile, use the no form of this command.

media-profile {profile-id}

no media-profile {profile-id}

Syntax Description

profile-id

New or existing numeric ID. The valid range is from 1 to 65535.


Defaults

None

Command Modes

Media service media -processing

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

None

Examples

This example shows how to configure media-profile 1:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# media-profile 1
mxe(config-media-serv-media-profile)# 

Related Commands

Command
Description

show media-processing

Displays media-processing profiles.


media service media-processing

To enter the media service media-processing mode, use the media service media-processing command.

media service media-processing

Syntax Description

None

Defaults

None

Command Modes

Global configuration

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

None

Examples

This example shows how to enter the media service media-processing mode:

mxe# configure-terminal
mxe(config)# media service media-processing
mxe(config-media-serv)

mode

To specify the call control mode for the media in a stream profile, use the mode command. To remove this configuration, use the no form of this command.

mode {sendrecv | sendonly | recvonly} [forced]

no mode {sendrecv | sendonly | recvonly} [forced]

Syntax Description

sendrecv

Specifies send and receive.

sendonly

Specifies send only.

recvonly

Specifies receive only.

forced

(Optional) Specifies that the mode will be used regardless of an offer from the other side of a call.


s

Defaults

Send and receive.

Command Modes

Stream profile

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

None

Examples

This example shows how to configure the call control mode for a stream-profile 1

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# stream-profile 1
mxe(config-media-serv-stream-profile)# mode recvonly forced

Related Commands

Command
Description

show media-processing

Displays media-processing profiles.


packetization-mode

To specify the packetization mode of an H.264 attribute, use the packetization-mode command. To remove this configuration, use the no form of this command.

packetization-mode value

no packetization-mode value

Syntax Description

value

Specifies one of the following:

0—single Network Abstract Layer (NAL) mode

1non-interleaved mode


Defaults

0

Command Modes

Codec-profile attribute H.264

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

A codec profile must first be configured with the codec-profile (media service media-processing) command.

Examples

This example shows how to configure the packetization mode of codec profile 1:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# codec-profile 1
mxe(config-media-serv-codec-profile)# attribute h264
mxe(config-media-serv-codec-profile-attr-h264)# packetization-mode 1

Related Commands

Command
Description

codec-profile (media service media-processing)

Creates a codec profile.

show media-processing

Displays media-processing profiles.


packet-time

To specify the packet time for the stream-profile, use the packet-time command. To remove this configuration, use the no form of this command

packet-time value

no packet-tim value

Syntax Description

value

Specifies one of the following:

10 ms

20 ms


Defaults

Audio default is 20 ms.

Command Modes

Stream profile

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

A stream profile must first be configured with the stream-profile (media service stream-processing) command.

Examples

This example shows how to configure the packet time for a stream-profile 1:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# stream-profile 1
mxe(config-media-serv-stream-profile)# packet-time 10

Related Commands

Command
Description

show media-processing

Displays media-processing profiles.

stream-profile (media service stream-processing)

Creates a stream profile.


payload-number

To specify the payload used in Real Time Protocol (RTP) packets for a codec type, use the payload-number command. To remove payload configuration, use the no form of this command.

payload-number value

no payload-number value

Syntax Description

value

Payload number. The valid range is from 0 to 127.


Defaults

None

Command Modes

Codec profile

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

A codec profile must first be configured with the codec-profile (media service media-processing) command.

Examples

This example shows how to specify a payload number:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# codec-profile profile-id
mxe(config-media-serv-codec-profile)# payload-number 123

Related Commands

Command
Description

codec-profile (media service media-processing)

Creates a codec profile.

show media-processing

Displays media-processing profiles.


preference

To configure a dial-peer preference value, use the preference command. To remove the configuration, use the no form of this command.

preference value

no preference value

Syntax Description

value

The range is from 0 to 255.


Defaults

255

Command Modes

Dial-peer media-service

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.

1.3

The command name was corrected.


Usage Guidelines

Before using this command, you must first create a media-service dial peer with the dial-peer media-service command.

Examples

This example shows how to configure a preference value of 10 for dial-peer 1:

mxe# configure terminal
mxe(config)# dial-peer media-service 1
mxe(config-dial-peer)# preference 10

Related Commands

Command
Description

dial-peer media-service

Create a dial peer and enters the dial-peer media-service configuration mode.

show dial-peer media-service

Displays configuration information for one or all media-service dial peers.


quality (stream-profile)

To configure the quality preference for a stream profile, use the quailty command. To remove this configuration, use the no form of this command.

quality {motion | sharpness}

no quality {motion | sharpness}

Syntax Description

motion

Specifies preference for a higher frame rate.

sharpness

Specifies preference for a higher resolution.


Defaults

The default is sharpness.

Command Modes

Media service stream-processing

Supported User Roles

network-admin

Command History

Release
Modification

1.3

This command was introduced.


Usage Guidelines

A stream profile must first be created by using the stream-profile (media service stream-processing) command.

To configure the Cisco MXE-OS device to transmit the highest possible resolution at a lower frame rate, use the quality sharpness command. To configure the device to transmit the highest possible frame rate at a lower resolution, use the quality motion command.

Examples

This example shows how to configure a higher frame rate preference for stream profile 1:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# stream-profile 1
mxe(config-media-serv-stream-profile)# quality motion
 
   

Related Commands

Command
Description

max-trans-bandwidth (media-profile)

Configures the maximum transmit bandwidth within a media profile.

max-trans-bandwidth (stream-profile)

Configures the maximum transmit bandwidth within a stream profile.

resolution-profile (media service media-processing)

Creates or modifies a resolution profile.

stream-profile (media service stream-processing)

Creates a stream profile.

show media-processing

Displays media-processing profiles.


resolution-profile (media service media-processing)

To create or modify a resolution profile and enter the resolution-profile configuration mode, use the resolution-profile command. To remove a resolution-profile, use the no form of this command.

resolution-profile {profile-id}

no resolution-profile {profile-id}

Syntax Description

profile-id

Specifies a new or existing numeric ID. The valid range is from 1 to 65535.

Configure the resolutions for the profile:

180p—Select 180p (320 x 180)

360p—Select 360p (640 x 360)

4cif—Select 4cig (704 x 576)

4sif—Select 4sif (704 x 480)

720p—Select 720p (1280 x 720)

cif—Select CIF (352 x 288)

sif—Select SIF (352 x 240)

w288p—Select w288p (512 x 288)

w448p—Select w448p (768 x 448)

w576p—Select w576p (1024 x 576)

xga—Select XGA (1024 x 768)


Defaults

None

Command Modes

Media service media-processing

Supported User Roles

network-admin

Command History

Release
Modification

1.3

This command was introduced.


Usage Guidelines

You need to associate the resolution profile with a codec profile. For more information, see the Configuration Guide for Cisco MXE-OS.

If you do not configure a resolution profile, these are the default resolutions:

Outgoing main video stream to Cisco TelePresence System (CTS) endpoints: 720p

Outgoing main video stream for videoconferencing endpoints will be one of these resolutions depending on the negotiated bandwidth and the quality setting in the corresponding stream profile: 720p, w576p, w448p, 360p, w288p, 180p

Outgoing presentation stream to CTS endpoints: XGA

Outgoing presentation stream to videoconferencing endpoints will be one of these resolutions depending on the negotiated bandwidth and the quality setting in corresponding steam-profile: XGA, 4SIF, SIF, 4CIF, CIF

Examples

This example shows how to configure resolution-profile 1 to limit the resolutions transmitted to w576p and w488p:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# resolution-profile 1
mxe(config-media-serv-resolution-profile)# w448p
mxe(config-media-serv-resolution-profile)# w576p
 
   

Related Commands

Command
Description

codec-profile (media service media-processing)

Creates a codec profile.

max-trans-bandwidth (media-profile)

Configures the maximum transmit bandwidth within a media profile.

max-trans-bandwidth (stream-profile)

Configures the maximum transmit bandwidth within a stream profile.

quality (stream-profile)

Configures the quality preference for a stream profile.

show media-processing

Displays media-processing profiles.


session-bandwidth (media profile)

To configure the amount of session bandwidth used by all media in a media profile, use the session-bandwidth command. To remove the configuration, use the no form of the command.

session-bandwidth {value}

no session-bandwidth {value}

Syntax Description

value

Session bandwidth in bits per second (b/s). The range is 64000 to 32000000 b/s.


Defaults

None

Command Modes

Media profile configuration

Supported User Roles

network-admin

Command History

Release
Modification

1.2

This command was introduced.


Usage Guidelines

A media profile must first be created with the media-profile (media service media-processing) command.

It is common for videoconferencing endpoints to allocate session bandwidth as a bandwidth limit that is shared among all the streams within a session. For example, a session with audio, video, and content sharing (presentation) might have a 2 MB session bandwidth limit. When content sharing is not active, the video stream can use all the bandwidth except that required for audio. When content sharing is active, the bandwidth is shared between the video and the content sharing streams.

Examples

This example shows how to configure a session bandwidth of 3000000 b/s for media profile 1:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# media-profile 1
mxe(config-media-serv-media-profile)# session-bandwidth 3000000

Related Commands

Command
Description

show media-processing

Displays media-processing profiles.

media-profile (media service media-processing)

Creates or modifies a media profile and enters the media-profile mode.


session-protocol (dial-peer media-service)

To configure the signaling protocol for a dial peer, use the session-protocol command. To remove payload configuration, use the no form of this command.

session-protocol {sipv2}

no session-protocol {sipv2}

Syntax Description

sipv2

Specifies Session Initiation Protocol (SIP) Version 2.


Defaults

SIP Version 2

Command Modes

Dial-peer media-service

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

Before using this command, you must first create a media-service dial peer with the dial-peer media-service command.

Examples

This example shows how to configure the signalling protocol for a dial peer:

mxe# configure terminal
mxe(config)# dial-peer media-service 1
mxe(config-dial-peer)# session-protocol sipv2

Related Commands

Command
Description

dial-peer media-service

Creates a media-service dial peer.

show dial-peer media-service

Displays configuration information for one or all dial peers.


session-target (dial-peer media-service)

To configure the destination address for a dial peer, use the session-target command. To remove the configuration, use the no form of this command.

session-target {ipv4:destination-address}

no session-target {ipv4:destination-address}

Syntax Description

ipv4:destination-address

Specifies the IPv4 destination address.


Defaults

None

Command Modes

Dial-peer media-service

Supported User Roles

network-admin

Command History

Release
Modification

1.2

This command was introduced.


Usage Guidelines

Before using this command, you must first create a media-service dial peer with the dial-peer media-service command.

The session target destination address specifies the gateway for the outgoing call.

Examples

This example shows how to configure the session target destination address for a dial peer:

mxe# configure terminal
mxe(config)# dial-peer media-service 1
mxe(config-dial-peer)# session-target ipv4:10.194.58.41:5060

Related Commands

Command
Description

dial-peer media-service

Creates a media-service dial peer.

show dial-peer media-service

Displays configuration information for one or all dial peers.


show application

To display the Cisco MXE-OS device resource allocation configuration, use the show application command.

show application {all {configuration | history {value {minutes | hours | days} | active} | interfaces}} | {{mxe-interop {configuration | history {value {minutes | hours | days} | active} | interfaces}}

Syntax Description

all

Display all known applications within the Cisco MXE-OS. The optional keywords have these meanings along with any available configuration information:

configuration—Show application configuration

history—Show call detail history information

value—Enter a value for the number of days, hours, or minutes

active—Show call history information for all active calls

interfaces—Show application interfaces that are registered with the Cisco MXE-OS device

mxe-interop

Display information relevant to the call and media processing interoperability application. The optional keywords have these meanings:

configuration—Show application configuration

history—Show call history information

value—Enter a value for the number of days, hours, or minutes

active—Show call history information for all active calls

interfaces—Show application interfaces that are registered with the Cisco MXE-OS device


Defaults

None

Command Modes

EXEC

Supported User Roles

network-admin
network-operator

Command History

Release
Modification

1.1

This command was introduced.

1.2

The configuration and interfaces keywords were added.

1.3

The all and history keywords, and the mxe-interop application name were added.


Usage Guidelines

The show application history command provides a brief summary of Cisco MXE-OS call activity. The level of detail is useful during testing and deployment for determining general call processing and call termination activity.

Examples

This example shows how to display all Cisco MXE-OS information about services, applications, and service-related infrastructure:

mxe# show application all
application accessNumber 69
application scheduledResources 4
 
   
ctsman server-port 80
ctsman ip 10.194.60.34 80
ctsman ssl-hostname-check enable
ctsman username test
ctsman password ********
ctsman leg-limit 4
 
   
No calls have been recently traced
 
   
McuRegistrationService is operational
    URL is http://10.194.60.34:80/discovery/services/McuRegistrationService
 
   
CTSManConferenceServer is operational
    URL is http://10.194.60.64:80/mcu/services/McuService
 
   

This example shows how to display the Cisco MXE-OS resource allocation configuration:

mxe# show application configuration
application accessNumber 69
application scheduledResources 10
 
   

This example shows how to display information about recent calls:

mxe# show application history
 
   
Call from 4184565962 to 5084565862 started 3 minutes ago 
Call from 4184565961 to 3084565892 started 6 minutes ago and ran 
Call from 4184565979 to 4084565892 started 13 minutes ago and ran 1 minute
Call from 4184565998 to 5084565892 started 13 minutes ago and ran 1 minute
Call from 4184565977 to 6084565892 started 14 minutes ago and ran 1 minute
Call from 4184565996 to 7084565892 started 14 minutes ago and ran 
Call from 4184565975 to 8084565892 started 17 minutes ago and ran 
Call from 4184565994 to 9084565892 started 17 minutes ago and ran 1 minute
Call from 4184565993 to 8084565892 started 1 hour 9 minutes ago and ran 
Call from 4184565972 to 4084565892 started 1 hour 10 minutes ago and ran 1 minute
<output truncated>
 
   

This example shows how to display the application interfaces registered with the Cisco MXE-OS:

mxe# show application interfaces
                Interface                                                   URL
   CTSManConferenceServer        http://10.10.1.1:80/mcu/services/McuService
 
   

Related Commands

Command
Description

application accessNumber

Configures the Cisco MXE-OS SIP access number or trunk.

application scheduledResources

Configures the number of allocated Cisco MXE-OS resources for scheduled calls.


show call-detail

To display detailed information about an individual call that has used the Cisco MXE 5600, use the show call-detail command.

show call-detail call-id

Syntax Description

call-id

The range is from 1 to 65535.


Defaults

None

Command Modes

EXEC

Supported User Roles

network-admin
network-operator

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

To view all of the configured call ID numbers, use the show call-summary command.

Examples

This example displays the detail information regarding Call ID 73:

mxe# show call-detail 73
Call-ID : 73
Call Start Time : Thu Apr 29 02:11:31 2010
Call State : ESTABLISHED
Application SessionID :
VC_CTS_INTEROP_APP.00000011
Audio App Mux Time : Thu Apr 29 02:11:32 2010
Video App Mux Time : Thu Apr 29 02:11:32Call-ID : 73
Call Start Time : Thu Apr 29 02:11:31 2010
Call State : ESTABLISHED
Application SessionID : VC_CTS_INTEROP_APP.00000011
Audio App Mux Time : Thu Apr 29 02:11:32 2010
Video App Mux Time : Thu Apr 29 02:11:32 2010
--- Calling Party : 1058 ---
Device Type : vc
DialPeerID : 2
SIP Call-ID : 859e5100-bd81ead3-b3ad-293ac20a@10.194.58.41
----------- Local Audio ------------------
IP Addr : 10.194.60.67:16464
Direction : inactive
Codec : G722
Bandwidth : 64000 bps
---------- Local Video -----------------
IP Addr : 10.194.60.67:16466
Direction : inactive
Codec : H264
Bandwidth : 2250000 bps
IDR Send Time : Thu Apr 29 02:11:31 2010
----------- Remote Audio -----------------
IP Addr : 10.194.60.205:50322
Direction : inactive
Codec : G722
Bandwidth : 64000 bps
----------- Remote Video ---------------
IP Addr : 10.194.60.205:50324
Direction : inactive
Codec : H264
Bandwidth : 704000 bps
IDR Request Time : Thu Apr 29 02:11:35 2010
--- Called Party : 3002 ---
Device Type : cts
DialPeerID : 1
SIP Call-ID : 2770772368-22090
----------- Local Audio ------------------
IP Addr : 10.194.60.67:16468
Direction : inactive
Codec : mpeg4-generic
Bandwidth : 128000 bps
---------- Local Video -----------------
IP Addr : 10.194.60.67:16470
Direction : inactive
Codec : H264
Bandwidth : 2250000 bps
----------- Remote Audio -----------------
IP Addr : 0.0.0.0:16428
Direction : inactive
Codec : mpeg4-generic
Bandwidth : 128000 bps
----------- Remote Video ---------------
IP Addr : 0.0.0.0:16430
Direction : inactive
Codec : H264
Bandwidth : 2750000 bps

Related Commands

Command
Description

show call-summary

Displays summary information regarding calls that have used the Cisco MXE 5600.


show call-summary

To display summary information about calls that have used the Cisco MXE 5600, use the show call-summary command.

show call-summary

Syntax Description

None

Defaults

None

Command Modes

EXEC

Supported User Roles

network-admin
network-operator

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

For detailed information regarding individual call IDs, use the show call-detail command.

Examples

This example displays the summary information regarding calls:

mxe# show call-summary
CallID CallingParty CalledParty   State          Start         Time
------------------------------------------------------------------------
48     1018         3001          ESTABLISHED    Thu Apr 29    02:09:19 2010
65     1066         3001          ESTABLISHED    Thu Apr 29    02:08:15 2010
73     1058         3002          ESTABLISHED    Thu Apr 29    02:11:31 2010

Related Commands02:11:31 2010

Command
Description

show call-detail

Displays detailed information about an individual call that has used the Cisco MXE 5600.


show ctsman conference

To display Cisco Telepresence Manager (CTS Manager) conference information, use the show ctsman conference command.

show ctsman conference {[accessNumber | conferenceID | meetingID | active | all | detailed]}

Syntax Description

accessNumber

Displays information about all conferences for the specified access number.

conferenceID

Displays information about the specified conference ID.

meetingID

Displays information about the specified meeting ID.

active

Displays information about all active conferences.

all

Displays summary information about all scheduled conferences.

detailed

Displays detailed information about all scheduled conferences.


Defaults

None

Command Modes

EXEC

Supported User Roles

network-admin
network-operator

Command History

Release
Modification

1.1

This command was introduced.


Usage Guidelines

None

Examples

This example shows how to display information about all conference information:

mxe# show ctsman conference all
Meeting ID      Start time              End time       Access        Type
4100192427  Fri Mar 26 18:00 PDT  Fri Mar 26 18:30 PDT   11055           
            Sat Mar 27 18:00 PDT  Sat Mar 27 18:30 PDT   11055           
            Mon Mar 29 18:00 PDT  Mon Mar 29 18:30 PDT   11055           
            Wed Mar 31 18:00 PDT  Wed Mar 31 18:30 PDT   11055           
            Thu Apr 01 18:00 PDT  Thu Apr 01 18:30 PDT   11055           
            Fri Apr 02 18:00 PDT  Fri Apr 02 18:30 PDT   11055           
            Sat Apr 03 18:00 PDT  Sat Apr 03 18:30 PDT   11055           
            Mon Apr 05 18:00 PDT  Mon Apr 05 18:30 PDT   11055           
            Wed Apr 07 18:00 PDT  Wed Apr 07 18:30 PDT   11055           
            Thu Apr 08 18:00 PDT  Thu Apr 08 18:30 PDT   11055           
6100140281  Fri Mar 26 12:00 PDT  Fri Mar 26 12:30 PDT   11055           
7100186109  Fri Mar 26 10:00 PDT  Fri Mar 26 10:30 PDT   11055           
            Sun Mar 28 10:00 PDT  Sun Mar 28 10:30 PDT   11055           
            Tue Mar 30 10:00 PDT  Tue Mar 30 10:30 PDT   11055           
...

Related Commands

Command
Description

ctsman hostname

Enables the CTS Manager Open SSL hostname.

ctsman ip

Configures the CTS Manager IP address.

ctsman leg-limit

Configures the Cisco MXE-OS device resource allocations.

ctsman password

Configures the password for CTS Manager communications.

ctsman port

Configures the CTS Manager port number.

ctsman server-port

Configures the Cisco MXE-OS port number.

ctsman username

Configures the username for CTS Manager communications.


show ctsman config

To display the Cisco Telepresence Manager (CTS Manager) configuration, use the show ctsman config command.

show ctsman config

Syntax Description

This command has no keywords or arguments.

Defaults

None

Command Modes

EXEC

Supported User Roles

network-admin
network-operator

Command History

Release
Modification

1.1

This command was introduced.


Usage Guidelines

None

Examples

This example shows how to display the CTS Manager configuration:

mxe# show ctsman config 
ctsman enable
ctsman server-port 8443
ctsman ip 10.1.1.1
ctsman port 8080
ctsman username admin1
ctsman password admin1pw
ctsman hostname disable

Related Commands

Command
Description

ctsman hostname

Enables the CTS Manager Open SSL hostname.

ctsman ip

Configures the CTS Manager IP address.

ctsman leg-limit

Configures the Cisco MXE-OS device resource allocations.

ctsman password

Configures the password for CTS Manager communications.

ctsman port

Configures the CTS Manager port number.

ctsman server-port

Configures the Cisco MXE-OS port number.

ctsman username

Configures the username for CTS Manager communications.


show ctsman statistics

To display Cisco Telepresence Manager (CTS Manager) statistics, use the show ctsman statistics command.

show ctsman statistics

Syntax Description

This command has no keywords or arguments.

Defaults

None

Command Modes

EXEC

Supported User Roles

network-admin
network-operator

Command History

Release
Modification

1.1

This command was introduced.


Usage Guidelines

None

Examples

This example shows how to display CTS Manager statistics:

mxe# show ctsman statistics 
===================  Ctsman Legacy Gateway ===================
Registration Triggers Received :        164
Registrations that were successful :    388
Registrations that failed :             4513
Registrations that became stale due to heartbeat silence :      0
 
   
 
   
=================== CTSMan Legacy Interface===================
Heartbeat Messages :            7361
Conference Messages :           396
Trigger Messages :              164
Heartbeat Last Message :        Thu Jul 08 18:44 UTC

show dial-peer media-service

To display configuration information for one or all dial peers, use the show dial-peer media-service command.

show dial-peer media-service {summary | id dialpeer-id}

Syntax Description

summary

Specifies tabular output of all dial peers

id

Specifies a selected dial peer.

dialpeer-id

The range is from 1 to 65535.


Defaults

None

Command Modes

EXEC

Supported User Roles

network-admin
network-operator

Command History

Release
Modification

1.0

This command was introduced


Usage Guidelines

For the dialpeer-id argument use a dial peer ID created with the dial-peer media-service command.

Examples

These examples show how to display all dial peers and a selected dial peer:

mxe56# show dial-peer media-service summary
DialPeers
Id                  MediaProfileId      ApplicationProfile  
---------------------------------------------------------
1                   1                   mxe-interop         
2                   2                   mxe-interop         
3                   3                   mxe-interop-vcs     
4                   4                   mxe-interop-vcs 
 
   
mxe# show dial-peer media-service id 1
DialPeerProfile
         Id = 1,
         CallingPartyID = ,
         CallingPartyName = ,
         SessionTarget = ,
         DestinationPattern = ,
         ApplicationProfile = mxe-interop,
         MediaProfileId = 1,
         QosDscpValue = 0,
         Protocol = SIPV2,
         Preference = 10,
         Description = CTS calling and called dial-peer when VC connected to CUC
M,
ApplicationProfile
         Id = mxe-interop,
         CTSMediaProfId = 1,
         VCMediaProfId = 2,
         Action = Query,
         DeviceProfilePtOptimization = false,
MediaProfile
         Id = 1,
         Session-Bandwidth = 0,
         StreamProfilesCount = 2,
         StreamProfilesID(s) = 2,1,
StreamProfile
         Id = 2,
         Stream Type = Audio,
         AppMux = ENABLE,
         Bandwidth = 128000,
         Mode = SendReceive,
         StreamModeForced = NO,
         PTime = 20,
         Transport = RtpAvp,
         CodecProfilesCount = 2,
         CodecProfilesID(s) = 2,4,
CodecProfile
         Id = 2,
         CodecType = AACLD,
         PayloadNumber = 96,
         Frequency = 48000,
         mode = AAC-hbr,
CodecProfile
         Id = 4,
         CodecType = G711ULaw,
         PayloadNumber = 0,
         Frequency = 8000,
StreamProfile
         Id = 1,
         Stream Type = Video,
         AppMux = ENABLE,
         Bandwidth = 2250000,
         Mode = SendReceive,
         StreamModeForced = NO,
         PTime = 0,
         Transport = RtpAvp,
         CodecProfilesCount = 1,
         CodecProfilesID(s) = 1,
CodecProfile
         Id = 1,
         CodecType = H.264,
         PayloadNumber = 112,
         Frequency = 90000,
         packetization-mode = 1,
         profile-level-id = 42001f,
 
   

Related Commands

Command
Description

dial-peer media-service

Defines a dial peer and enters dial peer media service configuration mode.

show dial-peer media-service

Displays information for one or all media-service dial peers.


show media-processing

To display media-processing profiles, use the show media-processing command.

show media-processing {application-profile | codec-profile | media-profile | resolution-profile | stream-profile} {profile-id | summary}

Syntax Description

application-profile

Shows the application-profile configuration.

codec-profile

Shows the codec-profile configuration.

media-profile

Shows the media-profile configuration.

resolution-profile

Shows the resolution-profile configuration

stream-profile

Shows the stream-profile configuration.

profile-id

Application-, codec-, media-, or stream-profile ID.

summary

Shows summary configuration information for the selected profile.


Defaults

None

Command Modes

EXEC

Supported User Roles

network-admin
network-operator

Command History

Release
Modification

1.0

This command was introduced.

1.3

The resolution-profile keyword was added.


Usage Guidelines

None

Examples

These examples show how to display configurations for an application-profile summary and application-profile ID mxe-interop:

mxe# show media-processing application-profile summary 
AppProfiles Id    Action              DeviceProfilePtOpti CTSMediaProfId VCMediaProfId       
--------------------------------------------------------------------------------
mxe-interop         Query               false               1                   2
mxe-interop-vcs     Query               false               3                   4
 
   
mxe# show media-processing application-profile summary
AppProfiles
ID               Action     CTSMedia ProfId         VCMediaProfID
mxe-interop      Query      1                       2
mxe# show media-processing application-profile mxe-interop
ApplicationProfile
     Id=mxe-interop,
     CTSMediaProfId = 1,
     VCMediaProfId = 2,
     Action = Query,
 
   

These examples show how to display configurations for a codec-profile summary and codec-profile ID 1:

mxe# show media-processing codec-profile summary
id           CodecType         PayloadNumber     Frequency
1            H.264             112               90000
2            AACLD             96                48000
3            G711Ulaw          0                 8000
4            G722              9                 8000
 
   
mxe# show media-processing codec-profile id 1
ID=1,
CodecType=H.264,
Payload Number=112,
Frequency Value=90000,
Max-fs=3600,
Max-mbps=10800,
Profile-level-id=42001f,
 
   

These examples show how to display configurations for a media-profile summary and media-profile ID 1:

mxe# show media-processing media-profile summary
ID       Stream ProfilesCount     StreamProfilesId(s)
1        2                        1,2
2        2                        4,3
3        1                        5
 
   
mxe# show media-processing media-profile id 1
MediaProfile
     Id = 1,
     StreamProfilesCount = 2,
     StreamProfileID(s) = 1, 2,
 
   

These examples show how to display configurations for a resolution-profile summary and resolution-profile ID 3:

mxe# show media-processing resolution-profile summary
ResolutionProfiles
Id                  NumberOfResolutions 
--------------------------------------
3                   3                   
 
   
mxe# show media-processing resolution-profile id 3
ResolutionProfile
         Id = 3,
         NumberOfResolutions = 3,
         Resolutions = w576p,720p,w448p,
 
   

These examples show how to display configurations for a stream-profile summary and stream-profile ID 1:

mxe# show media-processing stream-profile summary
Id     Appmux         Stream Type    Codec profileID(s)   Pref
1      ENABLE         Video          1                    1
2      DISABLED       Video          2                    1
 
   
mxe# show media-processing stream-profile id 1
StreamProfile
     Id = 1,
     Stream Type = Video,
     AppMux = ENABLE,
     Bandwidth = 2250000, 
     Mode = SendReceive, 
     StreamModeForced = NO,      
     PTime = 0, 
     Transport = RtpAvp, 
     CodecProfilesCount = 1, 
     CodecProfilesId(s) = 1,

Related Commands

Command
Description

application-profile (media service media-processing)

Creates or modifies an application profile.

codec-profile (media service media-processing)

Creates or modifies a codec profile.

media-profile (media service media-processing)

Creates or modifies a media profile.

resolution-profile (media service media-processing)

Creates or modifies a resolution profile.

stream-profile (media service stream-processing)

Creates or modifies a stream profile.


show media-statistics

To display media statistics for an application session or endpoint, use the show media-statistics command.

show media-statistics {application-session-id} [endpoint-id audio | video]

Syntax Description

application-session-id

Specify the application session ID for the call.

endpoint-id

(Optional) Specify an endpoint.

audio

(Optional) Specify the endpoint media type.

video

(Optional) Specify the endpoint media type.


Defaults

None

Command Modes

EXEC

Supported User Roles

network-admin
network-operator

Command History

Release
Modification

1.2

This command was introduced.


Usage Guidelines

Use the show call-summary command to display the call ID, and the show call-detail call-id command to obtain the application-session-id. Then use the show media-statistics command to request live statistics for a specific application session.

When using the show media-statistics command to troubleshoot call setup, call failure, and call quality, check for these indicators:

Are the counters are increasing?

Is there packet loss?

Are there partial frames?

Check the bit rate for the audio and video streams on a per-endpoint basis to see the actual bit rate transmitted and received. This can help to troubleshoot low video quality issues.

See Table 5-1 for the field descriptions used in the following examples.

This example shows a summary of statistics for a point-to-point call between a videoconferencing endpoint (ID-1038) and a Cisco TelePresence System (CTS) (ID-2103).

In this example, the videoconferencing endpoint resolution is 360p (transmit) and 720p (receive). The CTS resolution is 720p (transmit and receive).

mxe# show media-statistics VC_CTS_INTEROP_APP.00000006
Endpoint-ID:1038
Statistics Parameters         Transmit            Receive
----------------------------------------------------------------------
AUDIO
Local : 10.194.60.75:16444    Remote : 10.194.60.49:51810
Codec
   center                     G722                G722
Frames
   center                     6956                6986
Frame Rate
   center                     100                 100
Frames Lost
   center                     ---                 0
Packets
   center                     3478                3494
VIDEO
Local : 10.194.60.75:16446    Remote : 10.194.60.49:50960
Codec
   center                     H264                H264
Resolution
   center                     640x360             1280x720
Frames
   center                     2074                2081
Frame Rate
   center                     30                  30
Frames Lost
   center                     ---                 0
Packets
   center                     2493                16000
IDR
   center                     3                   2
 
   
Endpoint-ID:2103
Statistics Parameters         Transmit            Receive
----------------------------------------------------------------------
AUDIO
Local : 10.194.60.75:16452    Remote : 10.194.60.230:20774
Codec
   center                     AAC-LD              AAC-LD
   auxilliary                 ---                 AAC-LD
Frames
   center                     6984                6958
   auxilliary                 ---                 0
Frame Rate
   center                     100                 100
   auxilliary                 ---                 30
Frames Lost
   center                     ---                 0
   auxilliary                 ---                 0
Packets
   center                     3492                3481
   auxilliary                 ---                 0
VIDEO
Local : 10.194.60.75:16454    Remote : 10.194.60.230:22704
Codec
   center                     H264                H264
Resolution
   center                     1280x720            1280x720
Frames
   center                     2082                2076
Frame Rate
   center                     30                  30
Frames Lost
   center                     ---                 0
Packets
   center                     14187               14027
IDR
   center                     6                   3
The '---' in the display indicates either the Stats Param type is not valid or stream is 
not present in that direction. 
 
   
For example 'Frames Lost' does not apply in the Tx direction.
Auxiliary audio stream is only received from CTS, not transmitted to it.
 
   

This example shows a summary of statistics for a point-to-point call between a videoconferencing endpoint (ID-1038) that is sharing content with a CTS (ID-2103).

In this example, the videoconferencing endpoint resolution is 360p (transmit) and 720p (receive) for main video. The CTS resolution is 720p (transmit and receive) for main video. For content sharing, the Cisco MXE-OS receives 720p from the videoconferencing endpoint and transmits XGA to the CTS (auxiliary stream).

The auxiliary field is the content sharing (presentation) stream to/from the CTS endpoint. Because the videoconferencing endpoint is presenting to the CTS endpoint, the Cisco MXE-OS only transmits to the CTS on the auxiliary video stream. It does not receive any auxiliary stream traffic from the CTS. This is reversed when the CTS endpoint is presenting to the videoconferencing endpoint.

mxe# show media-statistics VC_CTS_INTEROP_APP.00000006
Endpoint-ID:1038
Statistics Parameters         Transmit            Receive
----------------------------------------------------------------------
AUDIO
Local : 10.194.60.75:16444    Remote : 10.194.60.49:51810
Codec
   center                     G722                G722
Frames
   center                     18188               18222
Frame Rate
   center                     100                 100
Frames Lost
   center                     ---                 0
Packets
   center                     9094                9112
VIDEO
Local : 10.194.60.75:16446    Remote : 10.194.60.49:50960
Codec
   center                     H264                H264
Resolution
   center                     640x360             1280x720
Frames
   center                     5444                5435
Frame Rate
   center                     30                  30
Frames Lost
   center                     ---                 2
Packets
   center                     6142                39067
IDR
   center                     3                   7
Local : 10.194.60.75:16448    Remote : 10.194.60.49:50478
Codec
   center                     ---                 H264
Resolution
   center                     ---                 1280x720
Frames
   center                     ---                 573
Frame Rate
   center                     ---                 9
Frames Lost
   center                     ---                 0
Packets
   center                     ---                 2885
IDR
   center                     ---                 6
 
   
Endpoint-ID:2103
Statistics Parameters         Transmit            Receive
----------------------------------------------------------------------
AUDIO
Local : 10.194.60.75:16452    Remote : 10.194.60.230:20774
Codec
   center                     AAC-LD              AAC-LD
   auxilliary                 ---                 AAC-LD
Frames
   center                     18218               18192
   auxilliary                 ---                 0
Frame Rate
   center                     100                 100
   auxilliary                 ---                 30
Frames Lost
   center                     ---                 0
   auxilliary                 ---                 0
Packets
   center                     9109                9098
   auxilliary                 ---                 0
VIDEO
Local : 10.194.60.75:16454    Remote : 10.194.60.230:22704
Codec
   center                     H264                H264
   auxilliary                 H264                ---
Resolution
   center                     1280x720            1280x720
   auxilliary                 1024x768
Frames
   center                     5452                5447
   auxilliary                 292                 ---
Frame Rate
   center                     30                  30
   auxilliary                 5                   ---
Frames Lost
   center                     ---                 0
Packets
   center                     40277               37232
   auxilliary                 2557                ---
IDR
   center                     12                  5
   auxilliary                 3                   ---
mxe#                                                                         
 
   

This example shows a summary of statistics for a point-to-point call between a CTS (ID-2103) that is sharing content with a videoconferencing endpoint (ID-1038).

In this example, the videoconferencing endpoint resolution is 360p (transmit) and 720p (receive) for main video. The CTS resolution is 720p (transmit and receive) for main video. For content sharing, the Cisco MXE-OS receives XGA from the CTS (auxiliary stream) and transmits 4CIF to the videoconferencing endpoint.

The auxiliary field is the content sharing (presentation) stream to/from the CTS endpoint. Because the CTS is presenting to the videoconferencing endpoint, the Cisco MXE-OS only receives from the CTS on the auxiliary video stream. The Cisco MXE-OS does not transmit any auxiliary stream traffic to the CTS. This is reversed when the videoconferencing endpoint is presenting to the CTS.

mxe# show media-statistics VC_CTS_INTEROP_APP.00000006
Endpoint-ID:1038
Statistics Parameters         Transmit            Receive
----------------------------------------------------------------------
AUDIO
Local : 10.194.60.75:16444    Remote : 10.194.60.49:51810
Codec
   center                     G722                G722
Frames
   center                     40189               40220
Frame Rate
   center                     100                 100
Frames Lost
   center                     ---                 0
Packets
   center                     20094               20111
VIDEO
Local : 10.194.60.75:16446    Remote : 10.194.60.49:50960
Codec
   center                     H264                H264
Resolution
   center                     640x360             1280x720
Frames
   center                     12044               12017
Frame Rate
   center                     30                  30
Frames Lost
   center                     ---                 3
Packets
   center                     17222               86221
IDR
   center                     5                   13
Local : 10.194.60.75:16448    Remote : 10.194.60.49:50478
Codec
   center                     H264                ---
Resolution
   center                     704x576
Frames
   center                     591                 ---
Frame Rate
   center                     30                  ---
Packets
   center                     1739                ---
IDR
   center                     3                   ---
 
   
Endpoint-ID:2103
Statistics Parameters         Transmit            Receive
----------------------------------------------------------------------
AUDIO
Local : 10.194.60.75:16452    Remote : 10.194.60.230:20774
Codec
   center                     AAC-LD              AAC-LD
   auxilliary                 ---                 AAC-LD
Frames
   center                     40219               40194
   auxilliary                 ---                 2020
Frame Rate
   center                     100                 100
   auxilliary                 ---                 100
Frames Lost
   center                     ---                 0
   auxilliary                 ---                 0
Packets
   center                     20109               20099
   auxilliary                 ---                 1012
VIDEO
Local : 10.194.60.75:16454    Remote : 10.194.60.230:22704
Codec
   center                     H264                H264
   auxilliary                 ---                 H264
Resolution
   center                     1280x720            1280x720
   auxilliary                 ---                 1024x768
Frames
   center                     12053               12047
   auxilliary                 ---                 99
Frame Rate
   center                     30                  30
   auxilliary                 ---                 5
Frames Lost
   center                     ---                 0
   auxilliary                 ---                 0
Packets
   center                     87489               82767
   auxilliary                 ---                 919
IDR
   center                     19                  5
   auxilliary                 ---                 2
mxe#                                                                                                                                   
 
   

Table 5-1 shows the media-statistic fields and their descriptions:

Table 5-1 Show Media-Statistics Field Descriptions 

Statistic Parameters
Description

Audio

Statistics for the audio portion of call.

Video

Statistics for the video/content sharing portion of call.

Local

IPv4 address and RTP port on the Cisco MXE 5600.

Remote

IPv4 address and port of the remote endpoint.

Resolution

The endpoint transmit and receive video resolution.

Codec, frames, frame rate, frames lost, packets, and bytes (center | right | left | auxiliary)

Left and right audio stream data only appears for CTS or Cisco TelePresence Multipoint Switch (CTMS) endpoints.

IDR (center | auxiliary | legacyMix) stream

Instantaneous decoder refresh (IDR) frames.

The legacyMix audio stream only appears for CTMS endpoints for a WebEx-enabled CTMS conference.

---

Indicates that either the statistic parameter type is invalid or stream is not present in that direction.


Related Commands

Command
Description

application-profile (media service media-processing)

Creates or modifies an application profile.

codec-profile (media service media-processing)

Creates or modifies a codec profile.

media-profile (media service media-processing)

Creates or modifies a media profile.

stream-profile (media service stream-processing)

Creates or modifies a stream profile.


shutdown (interface)

To disable an IP interface so that no packets can go through it, use the shutdown command. To enable the interface, use the no form of this command.

shutdown

no shutdown

Syntax Description

None

Defaults

None

Command Modes

Interface configuration

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

If this command is issued during a Telnet or Secure Shell Protocol (SSH) session, it will disconnect calls on the management interface and drop calls on the Ethernet interface

Examples

This example shows how to disable the MGT1 interface:

mxe# configure terminal
mxe(config)# interface mgt1
mxe(config-if)# shutdown
 
   

This example shows how to enable the Ethernet 1/1:

mxe# configure terminal
mxe(config)# interface ethernet 1/1
mxe(config-if)# no shutdown

Related Commands

Command
Description

interface

Configures the Ethernet or management interface.


shutdown (sip)

To disable the Session Initiation Protocol (SIP) interface so that no packets can go through it, use the shutdown command. To enable the interface, use the no form of this command.

shutdown [forced]

no shutdown [forced]

Syntax Description

forced

(Optional) Terminates all in-progress or established SIP calls automatically.


s

Defaults

None

Command Modes

Media service media-processing SIP configuration

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

None

Examples

This example shows how to disable the SIP interface:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-service)# sip
mxe(config-media-service-sip)# shutdown

Related Commands

Command
Description

media service media-processing

Enters the media service media-processing mode.

sip

Configures the SIP interface.


sip

To configure the SIP interface and enter the SIP configuration mode, use the sip command. To remove the SIP interface, use the no form of this command.

sip

no sip

Syntax Description

This command has no keywords or arguments.

Defaults

None

Command Modes

Media service media-processing

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

None

Examples

This example shows how to configure the SIP interface:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# sip
mxe(config-media-serv-sip)# 

Related Commands

Command
Description

media service media-processing

Enters the media service media-processing mode.


stream-profile (media profile)

To apply a stream profile to media profile, use the stream-profile command. To remove this configuration, use the no form of this command.

stream-profile profile-id

no stream-profile profile-id

Syntax Description

profile-id

A profile ID configured with the stream-profile (media service stream-processing) command.


Defaults

None

Command Modes

Media profile

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

Before using this command, you must configure a stream profile with the stream-profile (media service stream-processing) command.

For information about stream profiles, see the Configuration Guide for Cisco MXE-OS.

Examples

This example shows how to apply stream-profile 1 to media-profile 1:

mxe# configure terminal
mxe(config)# media service stream-processing
mxe(config-media-serv)# media-profile 1
mxe(config-media-serv-media-profile)# stream-profile 1

Related Commands

Command
Description

stream-profile (media service stream-processing)

Creates or modifies a stream profile and enters the stream-profile configuration mode

show media-processing

Displays media-processing profiles.


stream-profile (media service stream-processing)

To create or modify a stream profile and enter the stream-profile configuration mode, use the stream-profile command. To remove this configuration, use the no form of this command.

stream-profile profile-id

no stream-profile profile-id

Syntax Description

profile-id

Numeric identifier. The range is from 1 to 65535.


Defaults

None

Command Modes

Media service stream-processing

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

For information about stream profiles, see the Configuration Guide for Cisco MXE-OS.

Examples

This example shows how to configure a stream profile:

mxe# configure terminal
mxe(config)# media service stream-processing
mxe(config-media-serv)# stream-profile 1
mxe(config-media-serv-stream-profile)# 

Related Commands

Command
Description

show media-processing

Displays media-processing profiles.


stream-type

To specify the stream type for a stream-profile, use the stream-type command. To remove this configuration and revert to the default, use the no form of this command.

stream-type {audio | video | presentation | bfcp}

no stream-type {audio | video | presentation | bfcp}

Syntax Description

audio

Configures the stream type as audio.

video

Configures the stream type as video.

presentation

Configures the stream type as presentation (for content sharing).

bfcp

Configures the stream type as Binary Floor Control Protocol (BFCP).


Defaults

Audio

Command Modes

Stream-profile

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.

1.2

The presentation and bfcp keywords were added.


Usage Guidelines

Before using this command, you must first create a stream profile with the stream-profile (media service stream-processing) command.

A media profile can include 0 or 1 presentation streams, and 0 or 1 BFCP streams. When you configure a presentation stream, you must also configure a BFCP stream. A presentation stream is subject to all the same options and constraints as a video stream.

Examples

This example shows how to configure the stream type for a stream-profile 1:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# stream-profile 1
mxe(config-media-serv-stream-profile)# stream-type video

Related Commands

Command
Description

show media-processing

Displays media-processing profiles.

stream-profile (media service stream-processing)

Create or modifies a stream profile and enter the stream-profile configuration mode.


transport

To configure the transport for a stream-profile's media, use the transport command. To remove this configuration, use the no form of this command.

transport {rtp-avp}

no transport {rtp-avp}

Syntax Description

rtp-avp

Configures Real Time Protocol (RTP) audio video profile (AVP).


Defaults

RTP/AVP

Command Modes

Stream-profile

Supported User Roles

network-admin

Command History

Release
Modification

1.0

This command was introduced.


Usage Guidelines

Before using this command, you must first create a stream profile with the stream-profile (media service stream-processing) command.

Examples

This example shows how to configure the transport for a stream-profile 1:

mxe# configure terminal
mxe(config)# media service media-processing
mxe(config-media-serv)# stream-profile 1
mxe(config-media-serv-stream-profile)# transport rtp-avp

Related Commands

Command
Description

show media-processing

Displays media-processing profiles.

stream-profile (media service stream-processing)

Create or modifies a stream profile and enter the stream-profile configuration mode.