The interoperability information for a particular release is
dependent on third-party certification testing done after the
release has been made public. Therefore, the interoperability
information may not be available until several months after the
release becomes publically available.
you have a configured IP address for
Cisco UCS Manager GUI, as well as a login account with administration privileges.
you have the installation media for the OS, either on a DVD or as an ISO image.
If the software requires an activation key, make sure you have that information
recommend that you install the OS from an ISO image that you map as a virtual
also install from a physical disk, but that method requires that you attach an
external USB CD/DVD drive to the blade on which you want to install the OS
using a KVM cable with a USB connector. For details, see the
Hardware Installation Guide for the blade server that you
are using. All hardware installation guides are available at the following URL:
you have the
UCS B-Series Drivers DVD or the ISO image of this DVD. If the operating
system is installed on a drive that is available through iSCSI, you must choose
the network folder to load the eNIC driver during the installation process
because iSCSI is available through the Ethernet portion of the VIC.
download the ISO image, you need to burn the image to a DVD or use a
third-party utility to mount the image on a laptop hard drive.
the installation, you will need to extract the appropriate driver image file
from this DVD to a location accessible to the server so that it can be mounted
as a virtual floppy.
server has an LSI MegaRAID controller, configure RAID settings for the drives
in your server. If you do not configure your LSI MegaRAID LUNs before
installing the OS, disk discovery failures might occur during the installation
and you may see error messages such as “No Device Found.”
Regardless of which version of the OS you install, the installation-target server must be associated with a properly configured service profile. The service profile contains all of the
information and settings that are applied to the server.
Use Cisco UCS Manager to configure pools that identify the physical and logical
resources on your network. You select from these pools as you build the
service profile for the server.
Cisco UCS allows you to define pools
for servers, MAC addresses, WWN addresses, UUID suffixes, and management IP addresses.
Configure one named VSAN for each uplink fabric to which the target
server is networked.
A named VSAN creates a connection to a specific external SAN fabric.
Associate each VSAN with a physical uplink port on its corresponding
For example, associate the VSAN that you created for Fabric A
with an available physical port on Fabric Interconnect A.
Create one vHBA policy for each uplink fabric to which the target server
This vHBA policy defines how the vHBA connects to the SAN.
If your server has an LSI MegaRAID controller, configure RAID settings
for the drives in your system by creating a Local Disk
If you do not configure your LSI MegaRAID LUNs before installing the
OS, disk discovery failures might occur during the installation and
you may see error messages such as “No Device Found.”
Create a boot policy for the type of installation you are preforming.
If you are installing the OS on an internal drive, define the following Boot Order:
Floppy (for Windows 2003 only)
If you are installing the OS in a bootable SAN LUN, define the following Boot Order:
Floppy (for Windows 2003 only)
If your server has two network interface cards (NICs), such as the Cisco UCS CNA M71KR-E, you must create separate vNIC policies for each card in order to get user-defined MAC addresses for both NICs.
If you only associate one vNIC policy with the service profile, Windows assigns a hardware-based MAC address to the second NIC.
If you later move the service profile to a different server, the hardware-based MAC address will not move with that profile, and any programs that link to the MAC address will not be able to locate the proper server.
Configure any other policies that you require to manage
A complete list of the available policies is included in the Cisco UCS Manager Configuration Guides.
Create a new service profile or modify an existing service profile for the target blade server. Make sure this service profile is associated the
network settings and policies that you created for the target server.
If you plan to install the same OS on multiple servers, you can also create a service profile template and associate that template with the configuration settings you created.
You can then use that template to create a unique service profile for each target server.
Associate the service profile with the target server and reboot the server.
When the target server is rebooted, the settings in the service profile are assigned to
You cannot mount an ISO installation or driver image until after the server has finished rebooting and Cisco UCS Manager has successfully associated the service profile with the server.
SAN Boot Topology Example
The following example shows the topology of a Cisco UCS domain that uses the SAN boot feature.
You cannot mount an ISO image on the server until it is associated with a service profile.
In your web browser, type or select the web link for
Cisco UCS Manager GUI.
The default web link for HTTP access is
http://UCSManager_IP for an IPv4 address, or
http://UCSManager_IP6 for an IPv6 address. The default web link for HTTPS access is https://UCSManager_IP for an IPv4 address, or https://UCSManager_IP6 for an IPv6 address. In a standalone configuration,
UCSManager_IP or UCSManager_IP6 are the IPv4 or IPv6 addresses, respectively, for the management port on the fabric
interconnect. In a cluster configuration,
UCSManager_IP or UCSManager_IP6 are the IPv4 or IPv6 addresses, respectively, assigned to
Cisco UCS Manager.
Cisco UCS Manager launch
Launch KVM Manager.
Security Alert dialog box appears, click
Yes to accept the security certificate and
UCS - KVM Launch Manager Login page, do the following:
Enter your Cisco UCS username and
Optional: If your
Cisco UCS implementation includes multiple domains, select the appropriate
domain from the
Domain drop-down list.
In the Service Profiles table of the KVM Launch Manager, do the following:
Locate the row containing the service profile and associated
server on which you want to install the OS.
In the Launch KVM column for that server, click Launch.
The KVM console opens in a separate window.
If the Caps Lock key on your keyboard is on when you open a KVM session, and you subsequently turn off your Caps Lock key, the KVM Console may continue to act as if Caps Lock is turned on. To synchronize the KVM Console and your keyboard, press Caps Lock once without the KVM Console in focus and then press Caps Lock again with the KVM Console in focus.
How you access virtual media depends on the version of the KVM Console that you are using. Do one of the following to access virtual media:
Click the Virtual Media tab.
Click the VM tab.
Select Tools > Virtual Media.
Click Add Image and navigate to the directory containing the installation ISO image.
Select the ISO image file and click Open.
In the Client
View area, check the check box in the Mapped column associated with the ISO file, then
wait for mapping to complete.
Click Details to see the mapping progress.
What to Do Next
Install the OS as described in the installation procedure that matches the OS you are installing.