Cisco UCS C-Series Servers VMware Installation Guide
VMware vSphere ESXi Installation
Downloads: This chapterpdf (PDF - 365.0KB) The complete bookPDF (PDF - 892.0KB) | Feedback

VMware vSphere ESXi Installation

VMware vSphere ESXi Installation

This chapter includes the following sections:

Installing VMware vSphere ESXi on an Internal Drive

This procedure describes how to install VMware ESXi and required drivers on an internal drive using CIMC GUI and the KVM Console.

Before You Begin
  • Make sure you have completed the prerequisites described in Installation Prerequisites Checklist.
  • If you are installing VMware on a Cisco UCS C200 M1 Server or Cisco UCS C250 M1 Server, make sure that the server is using an LSI 1064-based controller mezzanine card for RAID configuration. The VMware server software does not support integrated software RAID with the ICH10R controller.
Procedure
    Step 1   If you are installing the OS or drivers from virtual media, launch the KVM Console and mount the media as described in Mounting the Installation ISO Image.
    Step 2   Power cycle the server using one of the following methods:
    • In the KVM Console, go to the KVM tab and select Macros > Ctrl-Alt-Del.
    • In CIMC GUI, click Summary in the Navigation pane, then click Power Cycle Server in the Actions area of the Server Summary tab.
    • On the physical server, press the Power button.
    Step 3   (Optional)If you want to set the boot order that the server will use after the OS is installed, watch the boot messages and press F2 when prompted to enter BIOS setup, then set the boot order.

    For details, see Configuring the Server Boot Order Using the KVM Console.

    Step 4   To override the normal boot order and boot from the installation media, in the KVM tab of the KVM Console, watch the boot messages and press F6 when prompted to enter the Boot Menu.
    Step 5   On the Boot Menu screen, do one of the following:
    • If you are using an ISO image, select Cisco Virtual CD/DVD and press Enter.
    • If you are using a physical install disk, select the disk drive in which that disk resides and press Enter.

    The server reboots from the selected device and begins installing the OS from the image or disk.

    Step 6   Wait until the ESXi Welcome screen displays, then press Enter to start the installation process.
    Tip   

    If the installation disk or an installed network adapter cannot be detected, make sure that you are using the ESXi installation image that VMware has customized for Cisco as described in Installation Prerequisites Checklist.

    Step 7   (Optional)If you are experiencing slow response times when using the KVM window, you can change the mouse acceleration:
    1. In the KVM tab in the KVM Console, select Tools > Session Options.
    2. Select the Mouse tab.
    3. In the Mouse Acceleration field, select Linux.
    4. Click OK to apply your changes.
    Step 8   When the installer prompts you to select the location where you want to install the OS, select the installation-target drive and click Next.

    All non-RAID drives are listed by name. Volumes created by a RAID controller are listed as logical drives.

    Step 9   When the installer displays the Confirm Install screen, press F11 to confirm your selections and start the installation process.
    Step 10   When the installer displays the Installation Complete screen:
    • If you installed from an ISO installation image, go back to the VM tab or the Virtual Media Session dialog box in the KVM Console and unmap the installation ISO by clearing the check box in the Mapped column.
    • If you installed from physical disk, eject the disk and remove it from the server.
    Step 11   Press Enter to boot the installation-target drive with ESXi.

    For information about customizing ESXi, see your VMware ESXi documentation.


    Installing VMware vSphere ESXi on a Bootable SAN LUN

    This procedure describes how to install VMware ESXi on a bootable SAN LUN logical disk or RAID volume using CIMC GUI and the KVM Console.

    Before You Begin
    • Make sure you have completed the prerequisites described in Installation Prerequisites Checklist.
    • Configure a LUN or RAID volume on your SAN, then connect to the SAN and verify that one (and only one) path exists from the SAN HBA to the LUN. If you are using an LSI RAID controller or the onboard Intel ICH10R controller, see RAID Controller Considerations for more information.
    • If you are installing VMware on a Cisco UCS C200 M1 Server or Cisco UCS C250 M1 Server, make sure that the server is using an LSI 1064-based controller mezzanine card for RAID configuration. The VMware server software does not support integrated software RAID with the ICH10R controller.
    Procedure
      Step 1   If you are installing the OS or drivers from virtual media, launch the KVM Console and mount the media as described in Mounting the Installation ISO Image.
      Step 2   Power cycle the server using one of the following methods:
      • In the KVM Console, go to the KVM tab and select Macros > Ctrl-Alt-Del.
      • In CIMC GUI, click Summary in the Navigation pane, then click Power Cycle Server in the Actions area of the Server Summary tab.
      • On the physical server, press the Power button.
      Step 3   (Optional)If you want to set the boot order that the server will use after the OS is installed, watch the boot messages and press F2 when prompted to enter BIOS setup, then set the boot order.

      For details, see Configuring the Server Boot Order Using the KVM Console.

      Step 4   To override the normal boot order and boot from the installation media, in the KVM tab of the KVM Console, watch the boot messages and press F6 when prompted to enter the Boot Menu.
      Step 5   On the Boot Menu screen, do one of the following:
      • If you are using an ISO image, select Cisco Virtual CD/DVD and press Enter.
      • If you are using a physical install disk, select the disk drive in which that disk resides and press Enter.

      The server reboots from the selected device and begins installing the OS from the image or disk.

      Step 6   Wait until the ESXi Welcome screen displays, then press Enter to start the installation process.
      Tip   

      If the installation disk or an installed network adapter cannot be detected, make sure that you are using the ESXi installation image that VMware has customized for Cisco as described in Installation Prerequisites Checklist.

      Step 7   (Optional)If you are experiencing slow response times when using the KVM window, you can change the mouse acceleration:
      1. In the KVM tab in the KVM Console, select Tools > Session Options.
      2. Select the Mouse tab.
      3. In the Mouse Acceleration field, select Linux.
      4. Click OK to apply your changes.
      Step 8   When the installer prompts you to select the location where you want to install the OS, select the installation-target LUN and click Next.
      Step 9   When the installer displays the Confirm Install screen, press F11 to confirm your selections and start the installation process.
      Step 10   When the installer displays the Installation Complete screen:
      • If you installed from an ISO installation image, go back to the VM tab or the Virtual Media Session dialog box in the KVM Console and unmap the installation ISO by clearing the check box in the Mapped column.
      • If you installed from physical disk, eject the disk and remove it from the server.
      Step 11   Press Enter to boot the installation-target drive with ESXi.

      For information about customizing ESXi, see your VMware ESXi documentation.