Table Of Contents
Cable and Port Specifications
This appendix provides cable and port specifications, and includes the following sections:
Accessory Kit for the Cisco UCS Fabric Interconnect
The Cisco UCS 6248 Fabric Interconnect accessory kit includes the following items:
•2 slider rails
•2 rack-mount guides
•2 rack-mount brackets
•12 M4 x 0.7 x 8-mm Phillips countersunk screws
•10 10-32 rack nuts
•10 10-32 x 3/4-inch Phillips pan-head screws
•1 console cable with an RJ-45-RS-232 adapter and a DB9 adapter
•1 ground lug kit
•1 ESD wrist strap
•1 power cord clip (a wire clip that is used to retain the power cord)
•1 pointer document (specifies where to find the online product documentation)
Note Additional parts can be ordered from your customer service representative.
The console cable has an RJ-45 connector on one end and a DB9 connector on the other; this cable is used to connect into the RS-232 console (see Figure B-1) connection on a laptop.
Figure B-1 Console Cable
Table B-1 lists the pinouts for the RJ-45 connector on the console cable.
Table B-1 Cable Connector Pinouts
Signal Name P1, P1-45 Pins P2, DB-9 Pins Signal Name
The console port is an asynchronous RS-232 serial port with an RJ-45 connector.
Table B-2 lists the pinouts for the console port on the Cisco UCS 6200 Series Fabric Interconnect.
Depending on the laptop you use for the initial configuration, you may also want a USB 2.0 to Serial (9-pin) DB-9 RS-232 Adapter Cable as well as a terminal program like Hyperterminal or PuTTY (set to connect at 9600 baud, 8 data bits, 1 stop bit, no parity).
Supported Power Cords and Plugs
Each power supply has a separate power cord. Standard power cords or jumper power cords are available for connection to a power distribution unit having IEC 60320 C19 outlet receptacles. The jumper power cords, for use in cabinets, are available as an optional alternative to the standard power cords.
The standard power cords have an IEC C19 connector on the end that plugs into the power supplies. The optional jumper power cords have an IEC C19 connector on the end that plugs into the power supplies, and an IEC C20 connector on the end that plugs into an IEC C19 outlet receptacle.
Note Only the regular power cords or jumper power cords provided with the chassis are supported.
Table B-3 lists the power cords for the Cisco UCS 6200 Series Fabric Interconnect and provides their lengths in feet and meters.
AC Power Cord Illustrations
This section contains the AC power cord illustrations.
Figure B-2 SFS-250V-10A-AR
Figure B-3 CAB-9K10A-AU
Figure B-4 SFS-250V-10A-CN
Figure B-5 CAB-9K10A-EU
Figure B-6 SFS-250V-10A-ID
Figure B-7 SFS-250V-10A-IS
Figure B-8 CAB-9K10A-IT
Figure B-9 CAB-9K10A-SW
Figure B-10 CAB-9K10A-UK
Figure B-11 CAB-AC-250V/13A
Figure B-12 CAB-N5K6A-NA
Jumper Power Cord
Figure B-13 shows the plug connector on the optional jumper power cord for the Cisco UCS 6200 Series Fabric Interconnect. The plug plugs in to the Cisco UCS 6200 Series Fabric Interconnect power supply, while the connector plugs into the receptacle of a power distribution unit for a cabinet.
Figure B-13 CAB-C13-C14-JMPR, Jumper Power Cord