Getting Started Guide for Cisco UCS E-Series Servers, Release 2.x
Cisco IOS Software Command Reference—Cisco ISR 4451-X
Downloads: This chapterpdf (PDF - 1.35MB) The complete bookPDF (PDF - 5.75MB) | The complete bookePub (ePub - 2.02MB) | Feedback

Cisco IOS Software Command Reference—Cisco ISR 4451-X

This chapter provides the new Cisco IOS commands that were introduced for the E-Series Servers installed in the Cisco ISR 4451-X.


Note


The Cisco IOS commands are sometimes updated after original publication; therefore, for updated content, review the Cisco IOS Interface and Hardware Component Command Reference at http:/​/​www.cisco.com/​en/​US/​docs/​ios-xml/​ios/​interface/​command/​ir-cr-book.html.


This chapter includes the following sections:

debug platform software ucse

To debug the Cisco UCS E-Series Server (UCSE) platform software and display debug messages, use the debug platform software ucse command in privileged EXEC mode. To disable debug, use the no form of this command.

debug platform software ucse { all | error | normal }

no debug platform software ucse { all | error | normal }

Syntax Description

all

Displays all platform debug messages.

error

Displays error debug messages.

normal

Displays normal debug messages.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

Cisco IOS XE Release 3.9S

This command was introduced on the Cisco UCS E-Series Servers installed in the Cisco 4400 Series Integrated Services Router (ISR).

Usage Guidelines

After you use the debug platform software ucse all command, use the appropriate ucse command to display debug messages.

The following example shows how to display debug messages for the ucse subslot imc password-reset command:

Router# debug platform software ucse all   
Router#
Router# ucse subslot 2/0 imc password-reset 
 ucse2/0/0
Password reset command sent.
Router#
 IMC ACK: UCSE password reset successful for IMC
 ACK received for UCSE: Password Reset Command

hw-module subslot session

To start or close a Cisco Integrated Management Controller (CIMC) or host server module session, use the hw-module subslot session command in privileged EXEC mode.

hw-module subslot slot/port-adapter session { imc | server }

Syntax Description

slot/

Number of the router slot in which the server module is installed.

port-adapter

Number of the port adapter.

Note   

For Cisco UCS E-Series Servers, the port adapter number is 0.

imc

Starts a session with CIMC.

server

Starts a session with the host server module.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

Cisco IOS XE Release 3.9S

This command was introduced on the Cisco UCS E-Series Servers installed in the Cisco 4400 Series Integrated Services Router (ISR).

Usage Guidelines

Only one active session is allowed in the CIMC or server module at any time.

The following example shows how to start a CIMC session:

Router# hardware-module subslot 1/0 session imc

The following example shows how to start a server module session:

Router# hardware-module subslot 1/0 session server

imc ip dhcp

To configure a dynamic IP address for the Cisco Integrated Management Controller (CIMC), use the imc ip dhcp command in UCSE configuration mode. To unconfigure the dynamic IP address, use the no form of this command.

imc ip dhcp

no imc ip dhcp

Syntax Description

This command has no arguments or keywords.

Command Modes


UCSE configuration (config-ucse)

Command History

Release

Modification

Cisco IOS XE Release 3.9S

This command was introduced on the Cisco UCS E-Series Servers installed in the Cisco 4400 Series Integrated Services Router (ISR).

The following example shows how to configure a dynamic IP address for CIMC:

Router# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)# ucse subslot 1/0
Router(config-ucse)# imc ip dhcp
Router(config-ucse)#
 IMC ACK: DHCP enable received for IMC.
 
 IMC ACK: UCSE setting DHCP enable for IMC successful.

show interfaces ucse

To display Cisco UCS E-Series Server (UCSE) interface statistics, use the show interfaces ucse command in privileged EXEC mode.

show interfaces ucse slot/port-adapter/ucse-interface [ accounting | controller | counters | crb | dampening | description | etherchannel | history | irb | mac-accounting | monitor | mpls-exp | precedence | stats | summary | switchport ]

Syntax Description

slot/

Number of the router slot in which the server module is installed.

port-adapter/

Number of the port adapter.

Note   

For Cisco UCS E-Series Servers, the port adapter number is 0.

ucse-interface

Number of the UCSE interface.

Note   

For Cisco UCS E-Series Servers, the UCSE interface number can be 0 or 1.

accounting

(Optional) Displays the number of packets of each protocol type that have been sent through the interface.

controller

(Optional) Displays the interface, configuration, and controller status.

counters

(Optional) Displays the interface counters.

crb

(Optional) Displays interface routing or bridging information.

dampening

(Optional) Displays interface dampening information.

description

(Optional) Displays the interface description.

etherchannel

(Optional) Displays interface Ether Channel information.

history

(Optional) Displays interface history.

irb

(Optional) Displays interface routing or bridging information.

mac-accounting

(Optional) Displays interface MAC accounting information.

monitor

(Optional) Displays interface continuously.

mpls-exp

(Optional) Displays interface Multiprotocol Label Switching (MPLS) experimental accounting information.

precedence

(Optional) Displays interface precedence accounting information.

stats

(Optional) Displays the switching path, the packets in and packets out, and the characters in and characters out.

summary

(Optional) Displays the interface summary.

switchport

(Optional) Displays the switch port interface information.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

Cisco IOS XE Release 3.9S

This command was introduced on the Cisco UCS E-Series Servers installed in the Cisco 4400 Series Integrated Services Router (ISR).

The following example provides sample output from the show interfaces ucse slot/0/0 switchport command.

Router# show interfaces ucse 1/0/0 switchport

	Name: ucse 1/0/0
	Switchport: Enabled
	Administrative mode: trunk
	Operational Mode: trunk
	Administrative Trunking Encapsulation: dot1q
	Operational Trunking Encapsulation: native
	Negotiation of Trunking: Disabled
	Trunking Native Mode VLAN: 2352
	Trunking VLANs Enabled: 1-2349,2450-4094
	Voice VLAN: none

ucse subslot imc password-reset

To reset the Cisco Integrated Management Controller (CIMC) password, use the ucse subslot imc password-reset command in privileged EXEC mode.

ucse subslot slot/port-adapter imc password-reset

Syntax Description

slot/

Number of the router slot in which the server module is installed.

port-adapter

Number of the port adapter.

Note   

For Cisco UCS E-Series Servers, the port adapter number is 0.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

Cisco IOS XE Release 3.9S

This command was introduced on the Cisco UCS E-Series Servers installed in the Cisco 4400 Series Integrated Services Router (ISR).

Usage Guidelines

After you enter this command, at the next login, the system requests that you set a new password to access CIMC.

The following example shows how to reset the CIMC password:

Router# ucse subslot 1/0 imc password-reset
Router#
 IMC ACK: UCSE password reset successful for IMC

ucse subslot server

To reload, reset, start, or stop the hardware on the server module, use the ucse subslot server command in privileged EXEC mode.

ucse subslot slot/port-adapter server { reload | reset | start | stop }

Syntax Description

slot/

Number of the router slot in which the server module is installed.

port-adapter

Number of the port adapter.

Note   

For Cisco UCS E-Series Servers, the port adapter number is 0.

reload

Gracefully shuts down the server module and then powers it on.

reset

Resets the hardware on the server module.

start

Powers on the server module.

stop

Immediately powers down the server module.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

Cisco IOS XE Release 3.9S

This command was introduced on the Cisco UCS E-Series Servers installed in the Cisco 4400 Series Integrated Services Router (ISR).

Usage Guidelines

Use the reset keyword only to recover from a shutdown or failed state.


Caution


Using the reset keyword does not provide an orderly software shutdown and may impact file operations that are in progress.


The following example shows how to reload the server:

Router# ucse subslot 1/0 server reload
Router#
 IMC ACK: UCSE Server reload successful.

The following example shows how to reset the server:

Router# ucse subslot 1/0 server reset
Router#
 IMC ACK: UCSE Server reset successful.

The following example shows how to start the server:

Router# ucse subslot 1/0 server start
Router#
 IMC ACK: UCSE Server start successful.

The following example shows how to stop the server:

Router# ucse subslot 1/0 server stop
Router#
 IMC ACK: UCSE Server stop successful.

ucse subslot server password-reset

To reset the BIOS or RAID password, use the ucse subslot server password-reset command in privileged EXEC mode.

ucse subslot slot/port-adapter server password-reset { BIOS | RAID }

Syntax Description

slot/

Number of the router slot in which the server module is installed.

port-adapter

Number of the port adapter.

Note   

For Cisco UCS E-Series Servers, the port adapter number is 0.

BIOS

Resets the BIOS password.

RAID

Resets the RAID password.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

Cisco IOS XE Release 3.9S

This command was introduced on the Cisco UCS E-Series Servers installed in the Cisco 4400 Series Integrated Services Router (ISR).

Usage Guidelines

After you enter this command, at the next login, the system requests that you set a new password to access BIOS or configure RAID.

The following example shows how to reset the BIOS password:

Router# ucse subslot 1/0 server password-reset BIOS
Router#
 IMC ACK: UCSE password reset successful for BIOS

The following example shows how to reset the RAID password:

Router# ucse subslot 1/0 server password-reset RAID
Router#
 IMC ACK: UCSE password reset successful for RAID

ucse subslot shutdown

To gracefully shut down the server module, use the ucse subslot shutdown command in privileged EXEC mode.

ucse subslot slot/port-adapter shutdown

Syntax Description

slot/

Number of the router slot in which the server module is installed.

port-adapter

Number of the port adapter.

Note   

For Cisco UCS E-Series Servers, the port adapter number is 0.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

Cisco IOS XE Release 3.9S

This command was introduced on the Cisco UCS E-Series Servers installed in the Cisco 4400 Series Integrated Services Router (ISR).

The following example shows how to shut down the server module:

Router# ucse subslot 1/0 shutdown 
Router# 
 IMC ACK: UCSE Server shutdown successful.

ucse subslot statistics

To display or clear server module statistics, use the ucse subslot statistics command in privileged EXEC mode.

ucse subslot slot/port-adapter statistics [clear]

Syntax Description

slot/

Number of the router slot in which the server module is installed.

port-adapter

Number of the port adapter.

Note   

For Cisco UCS E-Series Servers, the port adapter number is 0.

clear

(Optional) Clears the server module statistics.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

Cisco IOS XE Release 3.9S

This command was introduced on the Cisco UCS E-Series Servers installed in the Cisco 4400 Series Integrated Services Router (ISR).

The following example shows how to display the server module statistics:

Router# ucse subslot 1/0 statistics 
 Count of number of shutdowns command : 1
 Count of number of status commands : 0
 Count of number of server raid password  : 1
 Count of number of imc password-reset : 2
 Count of number of server bios password reset : 1
 Count of number of server reload : 1
 Count of number of server reset : 1
 Count of number of server start : 1
 Count of number of server stop : 1
 Count of number of vlan commands : 0
 Count of number of access-port commands : 1
 Count of number of IMC configured IP or DHCP commands: 1

ucse subslot status

To display configuration information related to the hardware and software on the server module, use the ucse subslot status command in privileged EXEC mode.

ucse subslot slot/port-adapter status [detailed]

Syntax Description

slot/

Number of the router slot in which the server module is installed.

port-adapter

Number of the port adapter.

Note   

For Cisco UCS E-Series Servers, the port adapter number is 0.

detailed

(Optional) Displays detailed information about the server module, such as its status and settings of the reset and heartbeat-reset flags.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

Cisco IOS XE Release 3.9S

This command was introduced on the Cisco UCS E-Series Servers installed in the Cisco 4400 Series Integrated Services Router (ISR).

The following example shows how to display server status:

Router#  ucse subslot 1/0 status
CPU info
        Name         Cores    Version                                            
        ------------ -------- -------------------------------------------------- 
        CPU1         4        Intel(R) Xeon(R) CPU E5-2418L 0 @ 2.00GHz          
 
Memory info
        Name                 Capacity        Channel Speed (MHz) Channel Type    
        -------------------- --------------- ------------------- --------------- 
        Node0_Dimm0          Not Installed   Unknown             Unknown         
        Node0_Dimm1          16384 MB        1333                DDR3            
        Node0_Dimm2          8192 MB         1333                DDR3            
 
Hard drive info
        Slot Number Controller Status                 Manufacturer   Model          Drive Firmware Coerced Size   Type  SED   
        ----------- ---------- ---------------------- -------------- -------------- -------------- -------------- ----- ----- 
        1           SLOT-5     online                 ATA            ST91000640NS   CC02           952720 MB      HDD   false 
        2           SLOT-5     online                 ATA            ST91000640NS   CC02           952720 MB      HDD   false 
        3           SLOT-5     online                 ATA            ST91000640NS   CC02           952720 MB      HDD   false 
 
Virtual drive info
        Virtual Drive  Status               Name                     Size       RAID Level 
        -------------- -------------------- ------------------------ ---------- ---------- 
        0              Optimal                                       1905440 MB RAID 5     
 
PCI card info
        Name                 Slot       Vendor ID            Device ID            Product Name              
        -------------------- ---------- -------------------- -------------------- ------------------------- 
        PCIe Adapter1        0          0xe414               0x5716               Broadcom 5719 1 Gbps 4... 
        PCIe Adapter2        2          0x0010               0x7300               LSI 9240-8i MegaRAID S... 
 
Network Setting
            IPv4 Address: 10.1.1.2
            IPv4 Netmask: 255.255.255.0
            IPv4 Gateway: 10.1.1.1
 
            NIC Mode: shared_lom
            NIC Redundancy: none
            NIC Interface: ge1