Cisco UCS C-Series Servers Integrated Management Controller CLI Command Reference, Release 1.0(1x)
Commands
Downloads: This chapterpdf (PDF - 953.0KB) The complete bookPDF (PDF - 1.33MB) | Feedback

Commands

Contents

Commands

This chapter includes the following sections:

activate (firmware)

To activate CIMC firmware, use the activate command.

activate

This command has no arguments or keywords.

Command Default

None

Command Modes

Firmware (/cimc/firmware)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to activate CIMC firmware:

server# scope cimc
server /cimc # scope firmware
server /cimc/firmware # activate
server /cimc/firmware #                                                                               

Related Commands

Command

Description

show cimc

 

show version

 

cancel

To stop the technical support process, use the cancel command.

cancel

This command has no arguments or keywords.

Command Default

None

Command Modes

Technical support (/cimc/tech-support)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to stop the technical support process:

server# scope cimc
server /cimc # scope tech-support
server /cimc/tech-support # cancel 
This operation will cancel your current Tech Support upload.
Continue?[y|N]y
server /cimc/tech-support # 

Related Commands

Command

Description

start

 

clear (log)

To clear the CIMC log, use the clear command in log mode.

clear

This command has no arguments or keywords.

Command Default

None

Command Modes

Log (/cimc/log)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to clear the CIMC log:

server# scope cimc
server /cimc # scope log
server /cimc/log # clear
server /cimc/log #                                                                               

Related Commands

Command

Description

show sel

 

show sensor

 

clear (sel)

To clear the system event log, use the clear command in sel mode.

clear

This command has no arguments or keywords.

Command Default

None

Command Modes

System event log (/sel)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to clear the system event log:

server# scope sel
server /sel # clear
server /sel #                                                                               

Related Commands

Command

Description

show sel

 

show sensor

 

commit

To save configuration changes, use the commit command.

commit

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to save a configuration change:

server /http # set enabled yes
server /http* # commit
server http # 

Related Commands

Command

Description

discard

 

connect

To connect to either the server CLI or the server shell, use the connectcommand.

connect { host | | shell }

Syntax Description

host

Specifies the CLI on the server.

shell

Specifies the GNU bash shell on the server.

Command Default

None

Command Modes

Any command mode

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

Use theexitcommand to exit the GNU bash shell.

Examples

This example shows how to connect to the server shell:

server# connect shell
bash-3.2                                                                               

discard

To discard all configurations, use the discard command.

discard

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to discard all configurations:

server# discard
server#                                                                               

Related Commands

Command

Description

discard

 

exit

To leave any mode, use the exit command.

exit

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to exit bios mode:

server /bios # exit
server#                                                                               

Related Commands

Command

Description

scope

 

enter

 

factory-default (cimc)

To set the server to factory default, use the factory-default command.

factory-default

This command has no arguments or keywords.

Command Default

None

Command Modes

Cisco Integrated Manangement Controller (/cimc)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to set the server to factory default:

server# scope cimc
server /cimc # factory-default
This operation will reset the BMC configuration to factory default.
All your configuration will be lost.
Continue?[y|n] y                                                                              

generate-csr (certificate)

To generate a Certificate Request Signing (CSR), use the generate-csr command.

generate csr

This command has no arguments or keywords.

Command Default

None

Command Modes

Certificate (/certificate)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to generate a CSR :

server# scope certificate
server /certificate # generate-csr

Common Name (CN): abcCertificate
Organization Name (O): abcCo
Organization Unit (OU): 01
Locality (L): west
StateName (S): CA
Country Code (CC): US
Email: abcCo@abcCo.com
Continue to generate CSR?[y|N] y

-----BEGIN CERTIFICATE REQUEST-----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-----END CERTIFICATE REQUEST-----

server /certificate #                                                                               

Related Commands

Command

Description

show certificate

 

show ssh

 

ping (network)

To ping, use the ping command in network mode.

ping address

Syntax Description

address

The IP address or the hostname.

Command Default

None

Command Modes

Network (/cimc/network)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to ping:

server# scope cimc
server /cimc # scope network
server /cimc/network # ping 209.165.200.225

Press CTRL+C to stop.
PING 209.165.200.225 (209.165.200.225): 56 data bytes
64 bytes from 209.165.200.225: seq=0 ttl=122 time=2.000 ms
64 bytes from 209.165.200.225: seq=1 ttl=122 time=2.000 ms
64 bytes from 209.165.200.225: seq=2 ttl=122 time=2.000 ms
64 bytes from 209.165.200.225: seq=3 ttl=122 time=3.000 ms
64 bytes from 209.165.200.225: seq=4 ttl=122 time=2.000 ms

--- 209.165.200.225 ping statistics ---
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 2.000/2.200/3.000 ms

server /cimc/network #                                                                               

power (chassis)

To manage server power, use the power command.

power {cycle | hard-reset | off | on | shutdown}

Syntax Description

cycle

Power cycles the server.

hard-reset

Hard resets the server.

off

Powers off the server.

on

Powers on the server.

shutdown

Shuts down the server.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to power off the server :

server# scope chassis
server /chassis # power off

This operation will change the server's power state.
Continue?[y|n] y

server /chassis #                                                                               

Usage Guidelines


  • Cycle—Power off, then power on.

  • Hard reset—Power off, then power on. Equivalent to pressing the front panel reset button, or performing an IPMI reset.

  • Shutdown—Graceful shut down of the OS, then power off.

Related Commands

Command

Description

show chassis

 

show psu

 

reapply (bios)

To reapply the boot order, use the reapplycommand in bios mode.

This command has no arguments or keywords.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release Modification
1.0(1x)

This command was introduced.

Examples

This example shows how to reapply the boot order:

server# scope bios
server /bios # re-apply
Boot order has been successfully re-applied
server /bios #                                                                               

Related Commands

Command

Description

set boot-order (bios)

 

show actual-boot-order

 

reboot (chassis)

To reboot the server, use the reboot command.

reboot

This command has no arguments or keywords.

Command Default

None

Command Modes

Cisco Integrated Management Controller (/cimc)

Command History

Release Modification
1.0(1)

This command was introduced.

1.0(1X)

This command was deprecated.

Examples

This example shows how to reboot the server:

server# scope cimc
server /cimc # reboot

This operation will reboot the BMC.
Continue?[y|n] y                                                                              

Related Commands

Command

Description

power

 

recover (bios)

To recover corrupted BIOS, use the recover command in firmware mode.

recover

This command has no arguments or keywords.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release Modification
1.0(1X)

This command was introduced.

Usage Guidelines

Before executing the recover command, perform the following tasks:


  • Ensure that the BIOS recovery ISO image is available for your use

  • Launch the KVM Console

  • Power off server

  • Map the BIOS recovery ISO image using vMedia

Executing the recover command automatically powers the server on. After the recovery is finished, power cycle or reset the server.

Examples

This example shows how to recover corrupted BIOS:

server# scope bios
server /bios # recover

This operation will automatically power on the server to perform BIOS FW recovery.
Continue?[y|N]y

server /bios #                                                                               

Note


You can use the CLI or the KVM console to monitor the progress of the recovery.


Related Commands

Command

Description

show bios

 

show version

 

scope bios

To enter bios mode, use the scope bios command.

scope bios

This command has no arguments or keywords.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use bios mode to set the server boot order:


  • CDROM—CD-ROM boot

  • EFI—Extensible Firmware Interface boot

  • FDD—Floppy disk drive boot

  • HDD—Hard disk drive boot

  • PXE—Preboot Execution Environment boot

Examples

This example shows how to enter BIOS mode:

server# scope bios
server /bios #                                                                            

Related Commands

Command

Description

show bios

 

show firmware

 

scope certificate

To enter certificate mode, use the scope certificate command.

scope certificate

This command has no arguments or keywords.

Command Default

None

Command Modes

Certificate (/certificate)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use certificate mode to perform the following tasks:


  • Generate a certificate signing request

  • Upload a signed certificate

Examples

This example shows how to enter certificate mode:

server# scope certificate
server /certificate #                                                                              

Related Commands

Command

Description

generate-csr

 

show certificate

 

scope chassis

To enter chassis mode, use the scope chassis command.

scope chassis

This command has no arguments or keywords.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use chassis mode to set the following chassis properties:


  • Server description

  • Server locator LED state

Examples

This example shows how to enter chassis mode:

server# scope chassis
server /chassis #                                                                             

Related Commands

Command

Description

show chassis

 

show led

 

scope cimc

To enter cimc mode, use the scope cimc command.

scope cimc

This command has no arguments or keywords.

Command Default

None

Command Modes

Cisco Integrated Management Controller (/cimc)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use cimc mode to perform the following actions:


  • Reset the CIMC to factory defaults

  • Reboot the CIMC

Examples

This example shows how to enter cimc mode :

server# scope cimc
server /cimc #                                                                               

Related Commands

Command

Description

show cimc

 

show log (cimc)

 

scope fault

To enter fault mode, use the scope fault command.

scope fault

This command has no arguments or keywords.

Command Default

None

Command Modes

Fault (/fault)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use fault mode to set the following SNMP properties:


  • Community string

  • Platform event

Examples

This example shows how to enter fault mode :

server# scope fault
server /fault #                                                                               

Related Commands

Command

Description

show fault

 

show pef

 

scope firmware (bios)

To enter firmware mode, use the scope firmware command in bios mode.

scope firmware

This command has no arguments or keywords.

Command Default

None

Command Modes

Firmware (/bios/firmware)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use firmware mode to perform the following tasks:


  • Activate and upload firmware

  • Display firmware information

Examples

This example shows how to enter BIOS mode:

server# scope bios
server /bios # scope firmwware
server /bios/firmware #                                                                            

Related Commands

Command

Description

show bios

 

show firmware

 

scope http

To enter http mode, use the scope http command.

scope http

This command has no arguments or keywords.

Command Default

None

Command Modes

HTTP (/http)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use http mode to set the following HTTP properties:


  • Enabing or disabling HTTP

  • Specifying port numbers and the HTTP connection timeout

Examples

This example shows how to enter http mode :

server# scope http
server /http #                                                                               

Related Commands

Command

Description

show http

 

show http-port

 

scope ipblocking (network)

To enter ipblocking mode, use the scope ipblocking command in network mode.

scope ipblocking

This command has no arguments or keywords.

Command Default

None

Command Modes

IP blocking (/cimc/network/ipblocking)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use ipblocking mode to perform the following tasks:


  • Enable or disable IP blocking

  • Set failure count, failure window, and penalty time

Examples

This example shows how to enter ipblocking mode :

server# scope cimc
server /cimc # scope network
server /cimc/network # scope ipblocking
server /cimc/network/ipblocking #                                                                               

Related Commands

Command

Description

show ipblocking

 

set penalty-time

 

scope ipmi

To enter ipmi mode, use the scope ipmi command.

scope ipmi

This command has no arguments or keywords.

Command Default

None

Command Modes

Intelligent Platform Management Interface (/ipmi)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use ipmi mode to perform the following tasks:


  • Enable or disable IPMI

  • Create an encryption key

  • Set the security privilege level

Examples

This example shows how to enter ipmi mode :

server# scope ipmi
server /ipmi #                                                                               

Related Commands

Command

Description

show ipmi

 

set encryption-key

 

scope kvm

To enter kvm mode, use the scope kvm command.

scope kvm

This command has no arguments or keywords.

Command Default

None

Command Modes

Keyboard, video and mouse (/kvm)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use kvm mode to set the following KVM properties:


  • Encryption

  • KVM port number

  • Local video

  • Maximum sessions

Examples

This example shows how to enter kvm mode :

server# scope kvm
server /kvm #                                                                               

Related Commands

Command

Description

set max-sessions

 

show kvm

 

scope ldap

To enter ldap mode, use the scope ldap command.

scope ldap

This command has no arguments or keywords.

Command Default

None

Command Modes

Lightweight Directory Access Protocol (/ldap)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use ldap mode to perform the following LDAP properties:


  • Enable or disable LDAP

  • Set attribute and Base DN (Base Distinguished Name)

  • Enable encryption

  • Create LDAP server IP address and connection timeout

Examples

This example shows how to enter ldap mode :

server# scope ldap
server /ldap #                                                                               

Related Commands

Command

Description

set server-ip

 

show ldap

 

scope log (cimc)

To enter log mode, use the scope log command in cimc mode.

scope log

This command has no arguments or keywords.

Command Default

None

Command Modes

Log (/cimc/log)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use log mode to perform the following tasks:


  • Clear the CIMC trace log

  • Display CIMC trace log entries

Examples

This example shows how to enter log mode :

server# scope cimc
server /cimc # scope log
server /cimc/log #                                                                               

Related Commands

Command

Description

show entries

 

show log

 

scope network (cimc)

To enter network mode, use the scope network command in cimc mode.

scope network

This command has no arguments or keywords.

Command Default

None

Command Modes

Network (/cimc/network)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use network mode to perform the following tasks:


  • Enable DHCP and DNS

  • Create a host name

  • Set the NIC mode and redundancy

  • Create an IPv4 IP address, gateway, and netmask

  • Enable the VLAN membership feature

Examples

This example shows how to enter network mode :

server# scope cimc
server /cimc # scope network
server /cimc/network #                                                                               

Related Commands

Command

Description

set dhcp-enabled

 

show network

 

scope pef (fault)

To enter pef mode, use the scope pef command in fault mode.

scope pef pef-index

Syntax Description

pef-index

The index of a specific performance event filter. The range of valid values is 1 to 12. See Usage Guideline for a complete list of perfomance event filter indexes.

Command Default

None

Command Modes

Performance event filter (/fault/pef)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

Following is a list of the performance event filter indexes:


  • 1—Temperature Critical Assert Filter

  • 2—Temperature Warning Assert Filter

  • 3—Voltage Critical Assert Filter

  • 4—Current Assert Filter

  • 5—Fan Critical Assert Filter

  • 6—Processor Assert Filter

  • 7—Power Supply Critical Assert Filter

  • 8—Power Supply Warning Assert Filter

  • 9—Power Supply Redundancy Lost Filter

  • 10—Discrete Power Supply Assert Filter

  • 11—Memory Assert Filter

  • 12—Drive Slot Assert Filter

Examples

This example shows how to enter pef mode:

server# scope fault
server /fault # scope pef 3
server /fault/pef #                                                                            

Related Commands

Command

Description

show pef

 

scope sel

To enter sel mode, use the scope sel command.

scope sel

This command has no arguments or keywords.

Command Default

None

Command Modes

System event log (/sel)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use sel mode to perform the following tasks:


  • Clear the system event log

  • Show configuration and system event log entries

Examples

This example shows how to enter sel mode :

server# scope sel
server /sel #                                                                               

Related Commands

Command

Description

show entries

 

show sel

 

scope sensor

To enter sensor mode, use the scope sensor command.

scope sensor

This command has no arguments or keywords.

Command Default

None

Command Modes

Sensor (/sensor)

Command History

Release Modification
1.0(1X)

This command was introduced.

Usage Guidelines

You use sensor mode to display fan, psu, psu-redundancy, temperature, and voltage sensors information.

Examples

This example shows how to enter sensor mode :

server# scope sensor
server /sensor #                                                                               

Related Commands

Command

Description

show fan

 

show voltage

 

scope sol

To enter sol mode, use the scope sol command.

scope sol

This command has no arguments or keywords.

Command Default

None

Command Modes

Serial over LAN (/sol)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use sol mode to perform the following tasks:


  • Enable or disable SoL

  • Set the baud rate

Examples

This example shows how to enter sol mode :

server# scope sol
server /sol #                                                                               

Related Commands

Command

Description

set baud-rate

 

show sol

 

scope ssh

To enter ssh mode, use the scope ssh command.

scope ssh

This command has no arguments or keywords.

Command Default

None

Command Modes

Secure Shell (/ssh)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use ssh mode to perform the following tasks:


  • Enable or disable SSH

  • Set the SSH port number and connection timeout interval

Examples

This example shows how to enter ssh mode :

server# scope ssh
server /ssh #                                                                               

Related Commands

Command

Description

set timeout (/ssh)

 

show ssh

 

scope tech-support (cimc)

To enter tech-support mode, use the scope tech-support command in cimc mode.

scope tech-support

This command has no arguments or keywords.

Command Default

None

Command Modes

Technical support (/cimc/tech-support)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use tech-support mode to set up the TFTP path and server address.

Examples

This example shows how to enter tech-support mode :

server# scope cimc
server /cimc # scope tech-support
server /cimc/tech-support #                                                                               

Related Commands

Command

Description

show tech-support

 

start

 

scope trap-destination (fault)

To enter trap-destination mode, use the scope trap-destination command in fault mode.

scope trap-destination trap-destination-index

Syntax Description

trap-destination-index

The index of a specific trap destination. The range of valid values is 1 to 4. See Usage Guideline for a complete list of trap destination indexes.

Command Default

None

Command Modes

Trap destination (/fault/trap-destination)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

A trap destination index corresponds to a specific trap destination IP address. There are up to four possible trap destination indexes. You pair an index with an IP address using the set addr command in trap-destination mode.

Examples

This example shows how to enter trap-destination mode:

server# scope fault
server /fault # scope trap-destination 4
server /fault/trap-destination #                                                                            

Related Commands

Command

Description

show trap-destination

 

scope user

To enter user mode, use the scope user command.

scope user { 1 | | 2 | | 3 | | 4 | | 5 | | 6 | | 7 | | 8 | | 9 | | 10 | | 11 | | 12 | | 13 | | 14 | | 15 }

Syntax Description

1

through

15

Specifies users 1 through 15.

Command Default

None

Command Modes

User (/user)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use user mode to perform the following tasks:


  • Enable user services

  • Create user names, roles, and passwords

Examples

This example shows how to enter user mode :

server# scope user
server /user #                                                                               

Related Commands

Command

Description

set user-name

 

show user

 

scope user-session

To enter user-session mode, use the scope user-session command.

scope user-session

This command has no arguments or keywords.

Command Default

None

Command Modes

User session (/user-session)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use user-session mode to display details about user sessions.

Examples

This example shows how to enter user-session mode :

server# scope user-session
server /user-session #                                                                               

Related Commands

Command

Description

show user

 

show user-session

 

scope vmedia

To enter vmedia mode, use the scope vmedia command.

scope vmedia

This command has no arguments or keywords.

Command Default

None

Command Modes

Virtual media (/vmedia)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You use vmedia mode to perform the following tasks:


  • Enable virtual media services

  • Enable encryption

Examples

This example shows how to enter vmedia mode :

server# scope vmedia
server /vmedia #                                                                               

Related Commands

Command

Description

set

 

show vmedia

 

set action (pef)

To set up an action for a performance event filter, use the set action command in pef mode.

set action { none | | power-off | | reboot | | power-cycle }

Syntax Description

none

Specifies no action.

power-off

Specifies that the server power off.

reboot

Specifies that the server reboots.

power-cycle

Specifies that the server power cycle.

Command Default

None

Command Modes

Performance event filters (/fault/pef)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

Following is a list of the performance event filter indexes:


  • 1—Temperature Critical Assert Filter

  • 2—Temperature Warning Assert Filter

  • 3—Voltage Critical Assert Filter

  • 4—Current Assert Filter

  • 5—Fan Critical Assert Filter

  • 6—Processor Assert Filter

  • 7—Power Supply Critical Assert Filter

  • 8—Power Supply Warning Assert Filter

  • 9—Power Supply Redundancy Lost Filter

  • 10—Discrete Power Supply Assert Filter

  • 11—Memory Assert Filter

  • 12—Drive Slot Assert Filter

Examples

This example shows how to set up an action for performance event filter 3:

server# scope fault
server /fault # scope pef 3
server /fault/pef # set action power-cycle
server /fault/pef* # commit
server /fault/pef #                                                                               

Related Commands

Command

Description

show pef

 

set addr (trap-destination)

To assign an IP address to a trap destination index, use the set addr command in trap-destination mode.

set addr ip-address

Syntax Description

ip-address

The IP address of the trap destination. The format is x.x.x.x.

Command Default

None

Command Modes

Trap destination (/fault/trap-destination)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to assign an IP address to a trap destination index:

server# scope fault
server /fault # scope trap-destination 3
server /fault/trap-destination # set addr 209.165.200.225
server /fault/trap-destination* # commit
server /fault/trap-destination #                                                                               

Related Commands

Command

Description

show trap-destination

 

set boot-order (bios)

To set the boot order for the server, use the set boot-order command in bios mode.

set boot-order boot-order

Syntax Description

boot-order

Sets the server boot order.

boot-order

The server boot order. Use the following boot order arguments, arranging them in the order that you want:


Command Default

None

Command Modes

BIOS (/bios)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

Type the boot order arguments using quotes and commas as delimiters. Following is an example:

"EFI","HDD","FDD","CDROM","PXE"

The arguments are not case sensitive.

Examples

This example shows how to set up the boot order for the server:

server# scope bios
server /bios # set boot-order "EFI","HDD","FDD","CDROM","PXE"
server /bios* # commit
server /bios #                                                                               

Related Commands

Command

Description

show bios

 

show actual-boot-order

 

set (chassis)

To describe the chassis, use the set command in chassis mode. You can also toggle the chassis locater LED.

set { description chassis-description | | locator-led { on | | off } }

Syntax Description

description

Specifies the description of the chassis.

chassis-description

The description of the chassis. The range of valid values is 1 to 64.

locator-led

Specifies whether the chassis locator LED.

on

Turns the server locator LED on.

off

Turns the server locator LED off.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

When you turn on the locator LED, it flashes. This allows you to easily locate the chassis.

Examples

This example shows how to turn on the locator LED:

server# scope chassis
server /chassis # set locator-led on
server /chassis* # commit
server /chassis #                                                                               

Related Commands

Command

Description

show chassis

 

show led

 

set description (chassis)

To set up a description for the chassis, use the set description command in chassis mode.

set description chassis-description

Syntax Description

chassis-description

The description of the chassis. The range of valid values is 1 to 64.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to :

server# scope chassis
server /chassis # set description testServer
server /chassis* # commit
server /chassis #                                                                               

Related Commands

Command

Description

show chassis

 

set enabled (trap-destination)

To enable or disable trap destinations on the server, use the set enabled command in trap-destination mode.

set enabled { no | | yes }

Syntax Description

no

Specifies that trap destination services are disabled.

yes

Specifies that trap destination services are enabled.

Command Default

None

Command Modes

Trap destination (/fault/trap-destination)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to enable trap destination services:

server# scope fault
server /fault # scope trap-destination 2
server /fault/trap-destination # set enabled yes
server /fault/trap-destination* # commit
server /fault/trap-destination #                                                                               

Related Commands

Command

Description

show trap-destination

 

set (fault)

To create an SNMP community, use the set command in fault mode. You can also enable platform events.

set { community-str community-name | | platform-event-enabled { no | | yes } }

Syntax Description

community-str

Specifies the SNMP community string (name).

community-name

The name of the SNMP community. The range of valid values is 1 to 18.

platform-event-enabled

Specifies whether platform event alerts are enabled or disabled.

no

Sets platform event alerts to disabled.

yes

Sets platform event alerts to enabled.

Command Default

None

Command Modes

Fault (/fault)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to create an SNMP community string:

server# scope fault
server /fault # set community-str cs100
server /fault* # commit
server /fault #                                                                               

Related Commands

Command

Description

show fault

 

show pef

 

set (http)

To set up Hyper Text Transfer Protocol (HTTP) services on the server, use the set command in http mode.

set { enabled { no | | yes } | | http-port port-number | | https-port port-number | | timeout time }

Syntax Description

enabled

Specifies whether HTTP services are enabled or disabled.

no

Specifies that HTTP is not enabled.

yes

Specifies that HTTP is enabled.

http-port

Sets the HTTP server port number.

port-number

The HTTP port number of the server. The range of valid values is 1 to 65536.

Note   

You also use this argument with the https-port keyword.

https-port

Sets the HTTPS server port number.

timeout

Sets the HTTP connection timeout time.

time

The connection timeout time, in seconds. The range of valid values is 60 to 10800.

Command Default

None

Command Modes

HTTP (/http)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to set the HTTP port number:

server# scope http
server /http # set http-port 80
server /http* # commit
server /http #                                                                               

Related Commands

Command

Description

show http-port

 

show https-port

 

set (ipblocking)

To set up IP blocking on the server, use the set command in ipblocking mode.

set { enabled { no | | yes } | | fail-count fail-number | | fail-window fail-window | | penalty-time penalty-time }

Syntax Description

enabled

Specifies whether IP blocking services are enabled or disabled.

no

Specifies that IP blocking is not enabled.

yes

Specifies that IP blocking is enabled.

fail-count

Sets the failure count.

fail-number

The failure number. The range of valid values is 3 to 10.

fail-window

Sets the failure window.

fail-window

The failure window. The range of valid values is 60 to 120.

penalty-time

Sets the blocking time.

penalty-time

The blocking time, in seconds. The range of valid values is 60 to 10800.

Command Default

None

Command Modes

IP blocking (/cimc/chassis/ipblocking)

Command History

Release Modification
1.0(1X)

This command was introduced.

Examples

This example shows how to enable IP blocking:

server# scope cimc
server /cimc # scope network
server /cimc/network # scope ipblocking
server /cimc/network/ipblocking # set enabled yes
server /cimc/network/ipblocking* # commit
server /cimc/network/ipblocking #                                                                                

Related Commands

Command

Description

show ipblocking

 

set (ipmi)

To set up IPMI services on the server, use the set command in ipmi mode.

set { enabled { no | | yes } | | encryption-key encryption-key | | privilege-level { admin | | read-only | | user } }

Syntax Description

enabled

Specifies whether IPMI is enabled or disabled.

no

Specifies that IPMI is not enabled.

yes

Specifies that IPMI is enabled.

encryption-key

Specifies the IPMI encryption key.

encryption-key

The IPMI encryption key. The valid value is 40 hex numbers.

privilege-level

Specifies the IPMI privilege level.

admin

Sets the IPMI privilege level to admin.

read-only

Sets the IPMI privilege level to read-only.

user

Sets the IPMI privilege level to user.

Command Default

None

Command Modes

Intelligent Platform Management Interface (/ipmi)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to set the IPMI encryption key:

server# scope ipmi 
server /ipmi # set encryption-key a9 62 b5 0a 68 6e e3 02 72 ce af f1 39 f8 1e 05 f5 19 d5 e1 7f f4 71 b9 9a 41 be e3 f5 06 4e cc 0f 63 67 2e a2 9c 74 d0
server /ipmi* # commit
server /ipmi #                                         

Related Commands

Command

Description

show ipmi

 

set (kvm)

To enable KVM on the server, use the set command in kvm mode.

set { enabled { no | | yes } | | encrypted { no | | yes } | | kvm-port port-number | | local- video { no | | yes } | | max-sessions number-of-sessions }

Syntax Description

enabled

Specifies whether KVM is enabled or disabled.

no

Specifies disable. Following are the uses of the no keyword:


  • Specifies that KVM is disabled when used with the enabled keyword.

  • Specifies that encryption is disabled when used with the encrypted keyword.

  • Specifies that local video is disabled when used with the local-video command.

yes

Specifies enable. Following are the uses of the yes keyword:


  • Specifies that KVM is enabled when used with the enabled command.

  • Specifies that encryption is enabled when used with the encrypted command.

  • Specifies that local video is enabled when used with the local-video command.

encrypted

Specifies whether KVM is encrypted or not encrypted.

kvm-port

Specifies the KVM port.

port number

The KVM port number. The range of valid values is 1 to 65535.

local-video

Specifies local video.

max-sessions

Specifies the maximum number of KVM sessions.

number-of-sessions

The maximum number of concurrent KVM sessions. The range of valid values is 1 to 4.

Command Default

None

Command Modes

Keyboard Video Mouse (/kvm)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

Use the local-video command to display the KVM session on any monitor attached to the server.

Examples

This example shows how to enable KVM:

server# scope kvm
server /kvm # set kvm enabled
server /kvm* # commit
server /kvm #                                                                               

Related Commands

Command

Description

show kvm

 

set (ldap)

To set up an LDAP (Lightweight Directory Access Protocol) directory on the server, use the set command in ldap mode.

set { attribute attribute-name | | base-dn base-dn-name | | enabled { no | | yes } | | encrypted { no | | yes } | | server-ip ip-address | | timeout time }

Syntax Description

attribute

Specifies the LDAP attribute.

attribute-name

The name of the attribute. The range of valid values is 1 to 64.

base-dn

Specifies the LDAP Base DN.

base-dn-name

The Base DN name. The range of valid values is 1 to 63.

enabled

Specifies whether LDAP is enabled or disabled.

no

Specifies disable. Following are the uses of the no keyword:


  • Specifies that LDAP is not enabled for the enabled keyword.

  • Specifies that encryption is not enabled for the encrypted keyword.

yes

Specifies enable. Following are the uses of the yes command:


  • Specifies that LDAP is enabled for the enabled command.

  • Specifies that encryption is enabled for the encrypted command.

encrypted

Specifies whether the Active Directory is encrypted or not encrypted.

server-ip

Specifies the Active Directory server IP address.

ip-address

The Active Directory server IP address. The format is X.X.X.X.

timeout

Specifies the Active Directory server connection timeout.

time

The wait time before a connection timeout, in seconds. The range of valid values is 0 to 1800.

Command Default

None

Command Modes

Lightweight Directory Access Protocol (/ldap)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You must be logged in as admin to set LDAP properties.

attribute —Specify an LDAP attribute that contains the role and locale information for the user. This property is always a name-value pair. The system queries the user record for the value that matches this attribute name. You can use the existing LDAP attribute that is mapped to CIMC user roles and locales. You can also create a custom attribute, such as the CiscoAVPair attribute, which has the following attribute ID:

1.3.6.1.4.1.9.287247.1

If you do not specify this property, user access is restricted to read-only.

enabled—When LDAP is enabled, all user authentication and role authorization is performed by Active Directory. CIMC ignores the local user database. If CIMC cannot establish a connection to Active Directory, it reverts to using the local user database.

Examples

This example shows how to set the Active Directory server timeout property:

server# scope ldap
server /ldap # set timeout 100
server /ldap* # commit
server /ldap #                                                                               

Related Commands

Command

Description

show ldap

 

set locator-led (chassis)

To turn the server locator LED on or off, use the set locator-led command in chassis mode.

set locator-led { off | | on }

Syntax Description

off

Turns the loactor LED off.

on

Turns the loactor LED on.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to turn on the locator LED:

server# scope chassis
server /chassis # set locator-led on
server /chassis* # commit
server /chassis #                                                                               

Related Commands

Command

Description

show chassis

 

show led

 

set (network)

To set up server network services on the server, use the set command in network mode.

set { alternate-dns-server ip-address | | dhcp-enabled { no | | yes } | | dns-use-dhcp | | hostname host-name | | mode { dedicated | | shared-lom | | shipping } | | preferred-dns-server | | redundancy { none | | active-standby } | | v4-addr ip-address | | v4-gateway ip-address | | v4-netmask netmask | | vlan-enabled { no | | yes } | vlan-id vlan-id | | vlan-priority priority-number }

Syntax Description

alternate-dns-server

Specifies an alternate DNS server.

ip-address

The DNS server IP address. You also use this argument with the preferred-dns-server, v4-addr, and v4-gateway keywords. The format is X.X.X.X.

dhcp-enabled

Specifies whether DHCP is enabled or disabled on the server.

no

Specifies disable. Following are the uses of the no keyword:


  • Specifies that DHCP is not enabled when used with the dhcp-enabled keyword.

  • Specifies that VLAN membership is not enabled when used with the vlan-enabled keyword.

yes

Specifies enable. Following are the uses of the yes keyword:


  • Specifies that DHCP is enabled when used with the dhcp-enabled command.

  • Specifies that encryption is enabled when used with the vlan-enabled command.

dns-use-dhcp

Specifies that DNS addresses are retrieved via DHCP.

hostname

Specifies the server name.

host-name

The name of the server. The range of valid values is 1 to 63.

mode

Specifies the server NIC mode.

dedicated

Sets the server network mode to dedicated.

shared-lom

Sets the server network mode to shared LOM.

shipping

Sets the server network mode to shipping.

preferred-dns-server

Specifies the preferred DNS server.

redundancy

Specifies whether redundancy is enabled or disabled on the server.

none

Sets server redundancy to none.

active-standby

Sets server redundancy to active standby failover.

v4-addr

Sets the server IPv4 IP address.

v4-gateway

Sets the server IPv4 gateway.

v4-netmask

Sets the server IPv4 netmask.

net-mask

The IPv4 netmask. The format is X.X.X.X.

vlan-enabled

Specifies whether server to VLAN membership is enabled or disabled.

vlan-id

Sets the VLAN ID.

vlan-id

The identification number of the VLAN.

vlan-priority

Sets the VLAN priority.

priority-number

The priority number of the VLAN.

Command Default

None

Command Modes

Network (/cimc/network)

Command History

Release Modification
1.0(1)

This command was introduced.

1.0(1x)

The shipping keyword was introduced.

Usage Guidelines

You must log in as a user with admin privileges to configure network properties.

mode — The CIMC network settings determine which ports can reach the CIMC. The following network mode options are available, depending on your platform:


  • Dedicated—A connection to the CIMC is available through the management Ethernet port or ports.

  • Shared LOM—A connection to the CIMC is available only through the LAN On Motherboard (LOM) Ethernet host ports.

  • Shipping—A connection to the CIMC is available through the management Ethernet port or ports using a limited factory default configuration.


Note


In shared LOM mode, all host ports must belong to the same subnet.


active-standby—Active/standby failover lets you use a standby security appliance to take over the functionality of a failed unit. When the active unit fails, it changes to the standby state, while the standby unit changes to the active state. The appliance that becomes active assumes the IP addresses and MAC addresses of the failed unit and begins to pass traffic.

vlan-enabled —When you use the VLAN commands, you are commiting your server to a membership in a particular VLAN. Following are the advantages of becoming a member of a VLAN:
  • Provides traffic isolation, which leads to enhanced security.

  • Reduces broadcast and multicast traffic, which leads to improved network performance.

Examples

This example shows how to enable DHCP:

server# scope cimc
server /cimc # scope network
server /cimc/network # set dhcp-enabled yes
server /cimc/network* # commit
server /cimc/network #                                                                               

Related Commands

Command

Description

show dhcp

 

show network

 

set (sol)

To set up SoL (Serial over LAN) on the server, use the set command in sol mode.

set { baud-rate { 9600 | | 19200 | | 38400 | | 57600 | | 115200 } | enabled { no | | yes } }

Syntax Description

baud-rate

Specifies the SoL baud rate.

9600

Sets baud rate to 9600 .

19200

Sets baud rate to 19200.

38400

Sets baud rate to 38400.

57600

Sets baud rate to 57600.

115200

Sets baud rate to 115200.

enabled

Specifies whether SoL is enabled or disabled.

no

Sets SoL to disabled.

yes

Sets SoL to enabled.

Command Default

None

Command Modes

Serial over LAN (/sol)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You must log in as a user with admin privileges to configure serial over LAN.

Serial over LAN (SoL) is a mechanism that enables the input and output of the serial port of a managed system to be redirected via an SSH session over IP. SoL provides a means of reaching the host console via CIMC.

For redirection to SoL, the server console must have the following configuration:


  • Console redirection to serial port A

  • No flow control

  • Baud rate the same as configured for SoL

  • VT-100 terminal type

  • Legacy OS redirection disabled

The SoL session will display line-oriented information such as boot messages, and character-oriented screen menus such as BIOS setup menus. If the server boots an operating system or application with a bitmap-oriented display, such as Windows, the SoL session will no longer display. If the server boots a command-line-oriented operating system (OS), such as Linux, you may need to perform additional configuration of the OS in order to properly display in an SoL session.

In the SoL session, your keystrokes are transmitted to the console except for the function key F2. To send an F2 to the console, press the Escape key, then press 2.

Examples

This example shows how to set the baud rate:

server# scope sol
server /sol # set baud-rate 115200
server /sol* # commit
server /sol #                                                                              

Related Commands

Command

Description

show sol

 

set (ssh)

To set up SSH (Secure Shell) services on the server, use the set command in ssh mode.

set { enabled { no | | yes } | ssh-port port-number | | timeout time }

Syntax Description

enabled

Specifies whether SSH is enabled or disabled.

no

Sets SSH to disabled.

yes

Sets SSH to enabled.

ssh-port

Specifies the SSH port.

port-number

The SSH port number. The range of valid values is 1 to 65535.

timeout

Specifies the SSH connection timeout.

time

The wait time before a connection timeout, in seconds. The range of valid values is 60 to 10800.

Command Default

None

Command Modes

Secure Shell (/ssh)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You must log in as a user with admin privileges to configure SSH.

Examples

This example shows how to set the SSH port number:

server# scope ssh
server /ssh # set ssh-port 22
server /ssh* # commit
server /ssh #                                                                              

Related Commands

Command

Description

show ssh

 

set (user)

To set up on the server, use the set command in user mode.

set { enabled { no | | yes } | | name user-name | | password password | | role { admin | | read-only | | user } }

Syntax Description

enabled

Specifies whether user accounts are enabled or disabled.

no

Specifies that user accounts are not enabled.

yes

Specifies that user accounts are enabled.

name

Sets the name of the user.

user-name

The name of the user. The range of valid values is 1 to 70.

password

Sets up the password.

password

The password. The range of valid values is 1 to 80.

role

Sets up the users role.

admin

Sets the user role to admin.

read-only

Sets the user role to read-only.

user

Sets the user role to user.

Command Default

None

Command Modes

User (/user)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You must log in as a user with admin privileges to configure local users.

A user of the CLI will be one of three roles:


  • admin—Configuration and control

  • user—No configuration

  • read-only—No configuration or control

To recover from a lost admin password, see the Cisco UCS C-Series server installation and service guide for your platform.

Examples

This example shows how to enable user accounts:

server# scope user
server /user # set enabled yes
server /user* # commit
server /user #                                                                               

Related Commands

Command

Description

show user

 

show user-session

 

set (vmedia)

To set up VMedia (virtual media) services on the server, use the set command in vmedia mode.

set { enabled { no | | yes } | | encrypted { no | | yes } }

Syntax Description

enabled

Specifies whether VMedia services are enabled or disabled.

no

Specifies disable. Following are the uses of the no keyword:


  • Specifies that VMedia is disabled when used with the enabled keyword.

  • Specifies that encryption is disabled when used with the encrypted keyword.

yes

Specifies that VMedia is enabled.

Specifies enable. Following are the uses of the yes keyword:


  • Specifies that VMedia is enabled when used with the enabled command.

  • Specifies that encryption is enabled when used with the encrypted command.

encrypted

Sets up encryption for VMedia.

Command Default

None

Command Modes

Virtual media (/vmedia)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

You must log in as a user with admin privileges to configure virtual media.

Examples

This example shows how to enable VMedia:

server# scope vmedia
server /vmedia # set enabled yes
server /vmedia* # commit
server /vmedia #                                                                               

Related Commands

Command

Description

show vmedia

 

set cli output

To change the CLI output, use the set cli output command.

set cli output { default | | yaml }

Syntax Description

cli output

Specifies server CLI output.

default

Sets CLI output to default.

yaml

Sets CLI ouput to YAML (Yet Another Markup Language).

Command Default

None

Command Modes

Any command mode

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to change the CLI output to YAML:

server# set cli output yaml
CLI output format set to yaml
server#                                                                               

set path (tech-support)

To set the TFTP path, use the set path command in tech-support mode.

set path tftp-path

Syntax Description

tftp-path

The TFTP path.

Command Default

None

Command Modes

Technical support (/cimc/tech-support)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

Specifies the path to the support data file should be stored.

Perform this task along with set tftp-ip when requested by the Cisco Technical Assistance Center (TAC). This utility creates a summary report containing configuration information, logs and diagnostic data that will help TAC in troubleshooting and resolving technical issues.

Examples

This example shows how to set the TFTP path:

server# scope cimc
server /cimc # scope tech-support
server /cimc/tech-support # set path /test/test.bin
server /cimc/tech-support* # commit
server /cimc/tech-support #                                                                               

Related Commands

Command

Description

set tftp-ip

 

show tech-support

 

set send-alert (pef)

To enable performance event filter alerts on the server, use the set send-alert command in pef mode.

set send-alert { no | | yes }

Syntax Description

no

Specifies that performance event filter alerts are not enabled.

yes

Specifies that performance event filter alerts are enabled.

Command Default

None

Command Modes

Performance event filters (/fault/pef)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to enable performance event filter alerts on the server:

server# scope fault
server /fault # scope pef
server /fault/pef # set send-alert yes
server /fault/pef* # commit
server /fault/pef #                                                                               

Related Commands

Command

Description

show pef

 

set tftp-ip (tech-support)

To set the TFTP server IP address, use the set tftp-ip command in tech-support mode.

set tftp-ip ip-address

Syntax Description

ip-address

The IP address of the TFTP server. The format is X.X.X.X.

Command Default

None

Command Modes

Technical support (/cimc/tech-support)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

Specifies the IP address of the TFTP server on which the support data file should be stored.

Perform this task along with set path when requested by the Cisco Technical Assistance Center (TAC). This utility creates a summary report containing configuration information, logs and diagnostic data that will help TAC in troubleshooting and resolving technical issues.

Examples

This example shows how to set the TFTP server IP address:

server# scope cimc
server /cimc # scope tech-support
server /cimc/tech-support # set tftp-ip 209.165.200.225
server /cimc/tech-support* # commit
server /cimc/tech-support #                                                                               

Related Commands

Command

Description

set tftp-path

 

show tech-support

 

show actual-boot-order (bios)

To display the actual boot order, use the show actual-boot-order command in bios mode.

show actual-boot-order [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the actual boot order in list format.

Command Default

None

Command Modes

BIOS (/bios)

Command History

Release Modification
1.0(1x)

This command was introduced.

Examples

This example shows how to display the actual boot order:

server# scope bios
server /bios # show actual-boot-order

Boot Order   Type                      Boot Device                         
------------ ------------------------- ----------------------------------- 
1            CD/DVD                    CD-ROM                              
2            CD/DVD                    Cisco   Virtual CD/DVD  1.18        
3            Network Device (PXE)      Cisco NIC 23:0.0                    
4            Network Device (PXE)      MBA v5.0.5  Slot 0100               
5            Network Device (PXE)      MBA v5.0.5  Slot 0101               
6            Network Device (PXE)      MBA v5.0.5  Slot 0200               
7            Network Device (PXE)      MBA v5.0.5  Slot 0201               
8            Network Device (PXE)      Cisco NIC 22:0.0                    
9            Internal EFI Shell        Internal EFI Shell                  
10           FDD                       Cisco   Virtual HDD     1.18        
11           FDD                       Cisco   Virtual Floppy  1.18
        
server /bios # 

Related Commands

Command

Description

set boot-order

 

show bios

To display information about the BIOS, use the show bios command.

show bios [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the bios, in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

show bios displays the server boot order. show bios detail and show detail in bios mode displays the server boot order and firmware update/recovery information.

When you use the detail keyword, the boot order of the following available boot devices displays:


  • CDROM—Bootable CD-ROM

  • FDD—Floppy disk drive

  • HDD—Hard disk drive

  • PXE—PXE boot

  • EFI—Extensible Firmware Interface

Examples

This example shows how to display the server boot order:

server# show bios

Boot Order                   
---------------------------- 
CDROM,FDD,HDD,PXE,EFI

server# 

Related Commands

Command

Description

set boot-order

 

recover

 

show certificate

To display informaion about the server certificate, use the show certificate command.

show certificate [ detail ]

Syntax Description

detail

(Optional) Displays the whole certificate.

Command Default

None

Command Modes

Root (server#)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

show certificate displays the serial number of the certificate, and the dates the certificate is valid for. show certificate detail in root mode and show detail in certificate mode displays the whole certificate.

Examples

This example shows how to display the serial number of the certificate, and the dates the certificate is valid for:

server# show certificate

Serial Number    Valid From               Valid To                 
---------------- ------------------------ ------------------------ 
001              Apr 13 13:49:00 2009 GMT Apr 11 13:49:00 2019 GMT

server#

This example shows how to display the whole certificate:

server# show certificate detail

Certificate Information:
    Serial Number: 00
    Subject Country Code (CC): US
    Subject State (S): California
    Subject Locality (L): San Jose
    Subject Organization (O): ABC Inc.
    Subject Organizational Unit (OU): 
    Subject Common Name (CN): abcinc.com
    Issuer Country Code (CC): US
    Issuer State (S): California
    Issuer Locality (L): San Jose
    Issuer Organization (O): Cisco Systems Inc.
    Issuer Organizational Unit (OU): 
    Issuer Common Name (CN): cisco.com
    Valid From: Sep  8 22:53:59 2009 GMT
    Valid To: Sep  6 22:53:59 2019 GMT

server# 

Related Commands

Command

Description

generate-csr

 

upload

 

show chassis

To display information about the chassis, use the show chassis command.

show chassis [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the chassis, in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

show chassis displays information about the chassis in table format. show chassis detail and show detail in chassis mode displays serial number, product name, PID, UUID, and description. Additionally, it displays chassis power state and the state of the locator LED.

Examples

This example shows how to display information about the chassis in table format:

server# show chassis

Power Serial Number Product Name  UUID                                 
----- ------------- ------------- ------------------------------------ 
on    QTF-0934-00   R100-1120402  208F4277020FBADBADBEA80000DEAD00
     
server#

Related Commands

Command

Description

set locator-led

 

show cimc

To display information about CIMC, use the show cimc command.

show cimc [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about CIMC, in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

show cimc displays information about CIMC in table format. show cimc detail and show detail in cimc mode displays firmware version and boot loader version.

Examples

This example shows how to display information about CIMC in table format:

server# show cimc

Firmware Version     Current Time             
-------------------- ------------------------ 
1.0(0.86)            Fri Oct  2 12:19:17 2009
 
server#

Related Commands

Command

Description

show firmware

 

show log (cimc)

 

show configuration pending

To display uncommitted configuration commands, use the show configuration pending command.

show configuration pending

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example displays uncommitted configuration commands:

server /cimc/network *# show configuration pending
 
Modify  /cimc/network  
  hostname  SanJoseServer3  
  dhcp-enabled  yes  
  v4-addr  10.20.30.111  
  dns-use-dhcp  yes  

server /cimc/network *# 

Related Commands

Command

Description

commit

 

discard

 

show cpu (chassis)

To display information about the CPU, use the show cpu command in the chassis mode.

show cpu [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the CPU, in list format.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

show cpu displays a list of CPUs. show cpu detail displays information for each CPU .

Following are commands you use to manage your view of the list of CPUs:
  • Enter key—Next line

  • Space bar—Next page

  • q key—Quit

  • r key—Show the rest

Examples

This example shows how to display detailed information about the CPUs:

server# scope chassis
server /chassis # show cpu detail

Name CPU1:
    Manufacturer: Intel(R) Corporation
    Family: Xeon
    Thread Count : 8
    Cores : 4
    Serial No.: Not Specified
    Version: Intel(R) Xeon(R) CPU           L5520  @ 2.27GHz
    Speed (Mhz) : 2266
    Max. Speed (Mhz) : 4000
    Signature: "Signature: Type 0, Family 6, Model 26, Stepping 5
    Status: Enabled
Name CPU2:
    Manufacturer: Intel(R) Corporation
    Family: Xeon
    Thread Count : 8
    Cores : 4
    Serial No.: Not Specified
    Version: Intel(R) Xeon(R) CPU           L5520  @ 2.27GHz
    Speed (Mhz) : 2266
    Max. Speed (Mhz) : 4000
    Signature: "Signature: Type 0, Family 6, Model 26, Stepping 5
    Status: Enabled

server /chassis # 

Related Commands

Command

Description

show dimm

 

show psu

 

show dimm (chassis)

To display information about the DIMMs (dual inline memory modules) in the chassis, use the show dimm command in chassis mode.

show dimm [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the DIMMs, in list format.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

show dimmdisplays a list of DIMMs. show dimm detaildisplays capacity, speed, and type for each DIMM .

Following are commands you use to manage your view of the list of DIMMs:
  • Enter key—Next line

  • Space bar—Next page

  • q key—Quit

  • r key—Show the rest

Examples

This example shows how to display detailed information about the DIMMs:

server# scope chassis
server /chassis # show dimm detail

Name DIMM_A1:
    Capacity (MB): 2048
    Speed (MHz): 1067
    Type: Other
Name DIMM_A2:
    Capacity (MB): 0
    Speed (MHz): 1067
    Type: Other
Name DIMM_B1:
    Capacity (MB): 0
    Speed (MHz): 1067
    Type: Other
Name DIMM_B2:
    Capacity (MB): 0
    Speed (MHz): 1067
    Type: Other
Name DIMM_C1:
    Capacity (MB): 0
    Speed (MHz): 1067
    Type: Other
Name DIMM_C2:
    Capacity (MB): 0
    Speed (MHz): 1067
--More-- 

Related Commands

Command

Description

show cpu

 

show entries (log)

To display the CIMC event log, use the show entries command in log mode.

show entries [ detail ]

Syntax Description

detail

(Optional) Displays the CIMC event log in detail.

Command Default

None

Command Modes

Log (/cimc/log)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

show entriesdisplays trace log entries in continuous string format. show entries detail displays time, source, and description for each trace log entry, in list format.

Following are commands you use to manipulate your view of the log:
  • Enter key—Next line

  • Space bar—Next page

  • q key—Quit

  • r key—Show the rest

Examples

This example shows how to display the detailed event log:

server# scope cimc
server /cimc # scope log
server /cimc/log # show entries detail

Trace Log:
    Time: 1970 Jan 2 17:04:57
    Source: BMC:dropbear:-
    Description: "  pam_session_manager(sshd:session): session (37) opened for user admin from 10.21.115.69 by (uid=0) "
    Order: 0
Trace Log:
    Time: 1970 Jan 2 17:04:57
    Source: BMC:dropbear:-
    Description: "  pam_auth_status(sshd:session): Login Successfull for user=admin, host=10.21.115.69 "
    Order: 1
Trace Log:
    Time: 1970 Jan 2 17:04:57
    Source: BMC:dropbear:-
    Description: "  pam_pass_if(sshd:session): unknown option: privilege=privIsLoginUser "
    Order: 2
Trace Log:
    Time: 1970 Jan 2 17:04:57
    Source: BMC:dropbear:-
    Description: "  pam_ldap_manager(sshd:auth): Start -----------> "
    Order: 3
--More-- 

Related Commands

Command

Description

show entries (sel)

 

show entries (sel)

To display the system event log, use the show entriescommand in sel mode.

show entries [ detail ]

Syntax Description

detail

(Optional) Displays the system event log in detail.

Command Default

None

Command Modes

SEL (/sel )

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

show entries displays system event log entries in continuous strings. show entries detail displays time, source, and description for each system event log entry, in list format.

Following are commands you use to manipulate your view of the log:
  • Enter key—Next line

  • Space bar—Next page

  • q key—Quit

  • r key—Show the rest

Examples

This example shows how to display the system event log:

server# scope sel
server /sel # show entries

Time                Severity      Description                              
------------------- ------------- ---------------------------------------- 
[System Boot]       Informational " LED_PSU_STATUS: Platform sensor, OFF event was asserted" 
[System Boot]       Informational " LED_HLTH_STATUS: Platform sensor, GREEN was asserted" 
[System Boot]       Normal        " PSU_REDUNDANCY: PS Redundancy sensor, Fully Redundant was asserted" 
[System Boot]       Normal        " PSU2 PSU2_STATUS: Power Supply sensor for PSU2, Power Supply input lost (AC/DC) was deasserted" 
[System Boot]       Informational " LED_PSU_STATUS: Platform sensor, ON event was asserted" 
[System Boot]       Informational " LED_HLTH_STATUS: Platform sensor, AMBER was asserted" 
[System Boot]       Critical      " PSU_REDUNDANCY: PS Redundancy sensor, Redundancy Lost was asserted" 
[System Boot]       Critical      " PSU2 PSU2_STATUS: Power Supply sensor for PSU2, Power Supply input lost (AC/DC) was asserted" 
[System Boot]       Normal        " HDD_01_STATUS: Drive Slot sensor, Drive Presence was asserted" 
[System Boot]       Critical      " HDD_01_STATUS: Drive Slot sensor, Drive Presence was deasserted" 
[System Boot]       Informational " DDR3_P2_D1_INFO: Memory sensor, OFF event was asserted" 
[System Boot]       Critical      " DDR3_P1_C2_PRS: Presence sensor, Device Removed / Device Absent was asserted" 
[System Boot]       Critical      " DDR3_P1_C1_PRS: Presence sensor, Device Removed / Device Absent was asserted" 
[System Boot]       Critical      " DDR3_P1_B2_PRS: Presence sensor, Device Removed / Device Absent was asserted" 
[System Boot]       Critical      " DDR3_P1_B1_PRS: Presence sensor, Device Removed / Device Absent was asserted" 
[System Boot]       Critical      " DDR3_P1_A2_PRS: Presence sensor, Device Removed / Device Absent was asserted" 
[System Boot]       Normal        " DDR3_P1_A1_PRS: Presence sensor, Device Inserted / Device Present was asserted" 
[System Boot]       Critical      " DDR3_P2_F2_PRS: Presence sensor, Device Removed / Device Absent was asserted" 
[System Boot]       Critical      " DDR3_P2_F1_PRS: Presence sensor, Device Removed / Device Absent was asserted" 
--More-- 

Related Commands

Command

Description

show entries (log)

 

show fan (sensor)

To display information about the fan sensors, use the show fan command in sensor mode.

show fan [ detail ]

Syntax Description

detail

(Optional) Displays .

Command Default

None

Command Modes

Sensor (/sensor)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about the fan sensors:

Server# scope sensor
Server /sensor # show fan

Name                 Sensor Status        Reading    Units      Min. Warning    Max. Warning    Min. Failure    Max. Failure    
-------------------- -------------------- ---------- ---------- --------------- --------------- --------------- --------------- 
PSU1_FAN_1           Normal               6592       RPM        N/A             N/A             N/A             N/A             
PSU2_FAN_1           Normal               2560       RPM        N/A             N/A             N/A             N/A             
W793_FAN1_TACH1      Normal               5300       RPM        N/A             N/A             800             N/A             
W793_FAN1_TACH2      Normal               5400       RPM        N/A             N/A             800             N/A             
W793_FAN2_TACH1      Normal               5500       RPM        N/A             N/A             800             N/A             
W793_FAN2_TACH2      Normal               5400       RPM        N/A             N/A             800             N/A             
W793_FAN3_TACH1      Normal               5300       RPM        N/A             N/A             800             N/A             
W793_FAN3_TACH2      Normal               5500       RPM        N/A             N/A             800             N/A             
W793_FAN4_TACH1      Normal               5300       RPM        N/A             N/A             800             N/A             
W793_FAN4_TACH2      Normal               5500       RPM        N/A             N/A             800             N/A             
--More-- 

Server /sensor # show fan detail
Name PSU1_FAN_1:
    Sensor Status: Normal
    Reading: 7872
    Units: RPM
    Min. Warning: N/A
    Max. Warning: N/A
    Min. Failure: N/A
    Max. Failure: N/A
Name PSU2_FAN_1:
    Sensor Status: Normal
    Reading: 2496
    Units: RPM
    Min. Warning: N/A
    Max. Warning: N/A
    Min. Failure: N/A
    Max. Failure: N/A
Name W793_FAN1_TACH1:
    Sensor Status: Normal
    Reading: 5300
    Units: RPM
    Min. Warning: N/A
    Max. Warning: N/A
    Min. Failure: 800
    Max. Failure: N/A
Name W793_FAN1_TACH2:
    Sensor Status: Normal
    Reading: 5400
    Units: RPM
    Min. Warning: N/A
    Max. Warning: N/A
    Min. Failure: 800
    Max. Failure: N/A
Name W793_FAN2_TACH1:
    Sensor Status: Normal
    Reading: 5500
    Units: RPM
    Min. Warning: N/A
    Max. Warning: N/A
    Min. Failure: 800
    Max. Failure: N/A
Name W793_FAN2_TACH2:
    Sensor Status: Normal
--More-- 

Related Commands

Command

Description

show cpu

 

show fault

To display information about SNMP services on the server, use the show fault command.

show fault [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about SNMP services, in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

show fault displays information about SNMP services in table format. show fault, show fault detail, and show detail in fault mode display information about community strings and platform enabled events.

Examples

This example shows how to display SNMP services information in table format:

server# show fault

SNMP Community String Platform Event Enabled
--------------------- ----------------------
33West                yes
34West                no

server#                                                                               

Related Commands

Command

Description

show pef

 

show trap-destination

 

show firmware (cimc)

To display information about the firmware on the server, use the show firmware command in cimc mode.

show firmware [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about firmware, in list format.

Command Default

None

Command Modes

CIMC (/cimc)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

show firmware displays information about firmware in table format. show firmware detail and show detail in firmware mode display information about updates, firmware version, and boot loader version.

Examples

This example shows how to display information about updates, firmware version, and boot loader version:

server# scope cimc
server /cimc # show firmware detail

Firmware Image Information:
    Update Stage: NONE
    Update Progress: 100
    Current FW Version: 1.0(0.86)
    FW Image 1 Version: 1.0(0.86)
    FW Image 1 State: RUNNING ACTIVATED
    FW Image 2 Version: 1.0(0.74)
    FW Image 2 State: BACKUP INACTIVATED

server /cimc #  

Related Commands

Command

Description

show cimc

 

show version

 

show hdd (chassis)

To display information about installed hard disk drives (HDD) in the chassis, use the show hdd command in chassis mode.

show hdd [detail]

Syntax Description

detail

(Optional) Displays detailed information about the HDDs in list form.

Command Default

None

Command Modes

Chassis (/chassis #)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about hard disk drives in the chassis:

Server# scope chassis
Server /chassis # show hdd
Name                 Status               
-------------------- -------------------- 
HDD_01_STATUS        present              
HDD_02_STATUS        present              
HDD_03_STATUS        present              
HDD_04_STATUS        present     

Server /chassis # show hdd detail
Name HDD_01_STATUS:
    Status : present
Name HDD_02_STATUS:
    Status : present
Name HDD_03_STATUS:
    Status : present
Name HDD_04_STATUS:
    Status : present

Server /chassis #

Related Commands

Command

Description

show psu

 

show http

To display information about HTTP services on the server, use the show http command.

show http [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about HTTP services, in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release Modification
1.0(1)

This command was introduced.

Usage Guidelines

show http displays HTTP information in table format. show http detail and show detail in http mode display information about HTTP ports, session timeout, and session activity.

Examples

This example shows how to display information about HTTP services in table format:

server# show http

HTTP Port  HTTPS Port Timeout  Active Sessions Enabled
---------- ---------- -------- --------------- ------- 
80         443        1800     0               yes
     
server#

Related Commands

Command

Description

set http-port

 

set https-port

 

show ipblocking (network)

To display information about the network IP blocking configuration, use the show ipblocking command in network mode.

show ipblocking [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the IP blocking configuration in list format.

Command Default

None

Command Modes

IP blocking (/cimc/network)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about the IP blocking configuration:

server# scope cimc
Server /cimc # scope network      
server /cimc/network # show ipblocking detail

IP Blocking Setting:
    Enabled: no
    Fail Count: 5
    Fail Window: 60
    Blocking Time: 300

server /cimc/network # 

Related Commands

Command

Description

show network

 

show ipmi

To display information about the configuration and status of IPMI (Intelligent Platform Management Interface) on the server, use the show ipmi command.

show ipmi [detail]

Syntax Description

detail

(Optional) Displays detailed iinformation about the configuration and status of IPMI on the server in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about the configuration and status of IPMI:

server# show ipmi detail

IPMI over LAN Settings:
    Enabled: yes
    Encryption Key: abcdef01234567890abcdef01234567890abcdef
    Privilege Level Limit: admin

server# 

Related Commands

Command

Description

set enabled (ipmi)

 

set encryption-key (ipmi)

 

show kvm

To display information about the KVM, use the show kvm command.

show kvm [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the KVM in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about the KVM:

server# show kvm

Encryption Enabled Local Video      Active Sessions Enabled KVM Port 
------------------ ---------------- --------------- ------- -------- 
no                 no               0               yes     2068
     
server# 

Related Commands

Command

Description

set kvm-port

 

set max-sessions (kvm)

 

show ldap

To display information about the configuration and status of the Active Directory, use the show ldap command.

show ldap [ detail ]

Syntax Description

detail

(Optional) Displays detailed iinformation about the configuration and status of the Active Directory in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about the configuration and status of the Active Directory:

server# show ldap detail

LDAP Settings:
    Server IP: 10.20.30.136
    BaseDN: example.com
    Encrypted: no
    Timeout: 60
    Enabled: no
    Attribute: CiscoAvPair

server# 

Related Commands

Command

Description

set server-ip (ldap)

 

set base-dn (ldap)

 

show led (chassis)

To display information about the server LEDs, use the show led command in the chassis command mode.

show led [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the server LEDs in list format.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about the server LEDs:

server# scope chassis
server /chassis # show led

LED Name                  LED State  LED Color 
------------------------- ---------- -------- 
DDR3_P2_D1_INFO           OFF        AMBER    
DDR3_P1_A1_INFO           OFF        RED      
LED_HLTH_STATUS           ON         GREEN    
LED_FPID                  OFF        BLUE     
LED_PSU_STATUS            OFF        AMBER    
LED_DIMM_STATUS           ON         GREEN    
LED_CPU_STATUS            ON         GREEN

Related Commands

Command

Description

set locator-led

 

show network (cimc)

To display information about the server network configuration, use the show network command in cimc mode.

show network [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the server network configuration in list format.

Command Default

None

Command Modes

CIMC (/cimc)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about the server network configuration:

server# scope cimc
server /cimc # show network

DHCP Enabled VLAN Enabled 
------------ ------------ 
no           no
           
server#

Related Commands

Command

Description

set dhcp-enabled

 

show ipblocking

 

show pef (fault)

To display information about the configuration and status of PEFs (Platform Event Filters), use the show pef command in fault mode.

show pef [ pef-name ] [ detail ]

Syntax Description

pef-number

Displays information about the specified PEF. If the pef-number variable is omitted, the command displays information about all PEFs.

detail

(Optional) Displays detailed information in list form.

Command Default

None

Command Modes

Fault (/fault)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about the configuration and status of all PEFs:

Server# scope fault
Server /fault # show pef

Platform Event Filter Event                               Action      Send Alert         
--------------------- ----------------------------------- ----------- ------------------ 
1                     Temperature Critical Assert Filter  none        no                 
2                     Temperature Warning Assert Filter   none        no                 
3                     Voltage Critical Assert Filter      none        no                 
4                     Voltage Warning Assert Filter       none        no                 
5                     Current Assert Filter               none        no                 
6                     Fan Critical Assert Filter          none        no                 
7                     Fan Warning Assert Filter           none        no                 
8                     Processor Assert Filter             none        no                 
9                     Power Supply Critical Assert Filter none        no                 
10                    Power Supply Warning Assert Filter  none        no                 
11                    Power Supply Redundancy Lost Filter none        no                 
12                    Discrete Power Supply Assert Filter none        no                 
13                    Memory Assert Filter                none        no                 
14                    Drive Slot Assert Filter            none        no                 

server /fault # 

Related Commands

Command

Description

set platform-event-enabled

 

show psu (chassis)

To display information about the PSUs (power supply units), use the show psu command in chassis mode.

show psu [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the PSUs in list format.

Command Default

None

Command Modes

Chassis (/chassis)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about the chassis PSUs:

server# scope chassis
server /chassis # show psu detail

Name PSU1:
    In. Power (Watts): 103
    Out. Power (Watts): 0
    Firmware : 
    Status : Present

server /chassis # 

Related Commands

Command

Description

show voltage

 

show psu (sensor)

To display information about the status of the PSU (power supply unit) sensors, use the show psu command in sensor mode.

show psu [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the PSU sensors in list format.

Command Default

None

Command Modes

Sensor (/sensor)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about the status of the PSU sensors:

server# scope sensor
server /sensor # show psu

Name                 Sensor Status        Reading    Units      Min. Warning    Max. Warning    Min. Failure    Max. Failure    
-------------------- -------------------- ---------- ---------- --------------- --------------- --------------- --------------- 
PSU1_POUT            Normal               68         Watts      N/A             652             N/A             680             
PSU1_PIN             Normal               76         Watts      N/A             652             N/A             680             
PSU1_STATUS          Normal               present                                                                               
PSU2_STATUS          Critical             absent
                                                                                
server /sensor # 

Related Commands

Command

Description

show voltage

 

show psu-redundancy (sensor)

To display information about the status of PSU (power supply unit) redundancy, use the show psu-redundancy command in sensor mode.

show psu-redundancy [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the status of PSU redundancy in list format.

Command Default

None

Command Modes

Sensor (/sensor)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about the status of PSU redundancy:

server# scope sensor
server /sensor #  show psu-redundancy detail

Name PSU_REDUNDANCY:
    Reading: full
    Sensor Status: Normal

server /sensor # 

Related Commands

Command

Description

show psu

 

show sol

To display information about the SoL (Serial over LAN) configuration, use the show sol command.

show sol [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the SoL (serial over LAN) configuration in list format.

Command Default

None

Command Modes

Root (/server#)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about the SoL configuration:

server# show sol detail

Serial Over LAN:
    Enabled: no
    Baud Rate(bps): 115200

server#
  

Related Commands

Command

Description

set baud-rate

 

show ssh

To display information about the SSH (Secure Shell) configuration on the server, use the show ssh command.

show ssh [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the SSH configuration in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about the SSH configuration:

server# show ssh detail

SSH Settings:
    SSH Port: 22
    Timeout: 10800
    Max Sessions: 4
    Active Sessions: 1
    Enabled: yes

server# 

Related Commands

Command

Description

set enabled (ssh)

 

set ssh-port (ssh)

 

show tech-support (cimc)

To display information about the configuration of the tech-support utility, use the show tech-support command in cimc mode.

show tech-support [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the configuration of the tech-support utility in list format.

Command Default

None

Command Modes

CIMC (/cimc)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about the configuration of the tech-support utility:

server# scope cimc
server /cimc # show tech-support detail

Tech Support:
    TFTP Server Address: 10.20.30.211
    TFTP Path: /user/tech-support
    Progress(%): 100
    Status: COMPLETED

server /cimc # 

Related Commands

Command

Description

set path (tech-support)

 

set tftp-ip (tech-support)

 

show temperature (sensor)

To display information about the status of the temperature sensors, use the show temperature command in sensor mode.

show temperature [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the status of the temperature sensors in list format.

Command Default

None

Command Modes

Sensor (/sensor)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about the status of the temperature sensors:

server# scope sensor
server /sensor # show temperature

Name                      Sensor Status  Reading    Units      Min. Warning Max. Warning Min. Failure Max. Failure 
------------------------- -------------- ---------- ---------- ------------ ------------ ------------ ------------ 
IOH_TEMP_SENS             Normal         42.0       C          N/A          80.0         N/A          85.0         
P2_TEMP_SENS              Normal         43.0       C          N/A          80.0         N/A          81.0         
P1_TEMP_SENS              Normal         45.0       C          N/A          80.0         N/A          81.0         
DDR3_P2_D1_TMP            Normal         28.0       C          N/A          90.0         N/A          95.0         
DDR3_P1_A1_TMP            Normal         30.0       C          N/A          90.0         N/A          95.0         
PSU1_TEMP_1               Normal         40.0       C          N/A          60.0         N/A          65.0         
PSU2_TEMP_1               Normal         40.0       C          N/A          60.0         N/A          65.0         
FP_AMBIENT_TEMP           Normal         22.0       C          N/A          40.0         N/A          45.0         

server /sensor # 

show trap-destination (fault)

To display information about SNMP trap destinations, use the show trap-destination command in fault mode.

show trap-destination [ trap-destination-number ] [ detail ]

Syntax Description

trap-destination-number

Displays information about only the specified SNMP trap destination. If the trap-destination-number variable is omitted, displays information about all SNMP trap destinations.

detail

(Optional) Displays detailed information about SNMP trap destinations in list format.

Command Default

None

Command Modes

Fault (/fault)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about the SNMP trap destinations:

server# scope fault
server /fault # show trap-destination
 
Trap Destination IP Address       Enabled  
---------------- ---------------- -------- 
1                209.165.200.225  yes      
2                0.0.0.0          no       
3                0.0.0.0          no       
4                0.0.0.0          no       

server /fault # 

Related Commands

Command

Description

set addr (trap-destination)

 

show user

To display information about user profiles on the server, use the show user command.

show user [ user-number ] [ detail ]

Syntax Description

user-number (Optional) Displays only the specified user profile. If the user-number variable is omitted, displays all user profiles.
detail

(Optional) Displays detailed information in list form.

Command Default

None

Command Modes

Root (server#)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about all user profiles:

server# show user

User   Name             Role     Enabled  
------ ---------------- -------- -------- 
1      admin            admin    yes      
2      jsmith           admin    yes      
3      (n/a)            (n/a)    no       
4      (n/a)            (n/a)    no       
5      bjones           readonly yes      
6      (n/a)            (n/a)    no       
7      (n/a)            (n/a)    no       
8      (n/a)            (n/a)    no       
9      (n/a)            (n/a)    no       
10     (n/a)            (n/a)    no       
11     (n/a)            (n/a)    no       
12     (n/a)            (n/a)    no       
13     (n/a)            (n/a)    no       
14     (n/a)            (n/a)    no       
15     (n/a)            (n/a)    no       

server# 

Related Commands

Command

Description

set enabled (user)

 

set name (user)

 

show user-session

To display information about current user sessions, use the show user-session command.

show user-session [ session-number ] [ detail ]

Syntax Description

session-number Displays information about a specific session.
detail

(Optional) Displays detailed information about current user sessions in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display user session information for all current user sessions:

server# show user-session
 
ID     Name             IP Address        Type         Killable 
------ ---------------- ----------------- ------------ -------- 
4      admin            10.20.30.123      CLI          yes      
2      admin            10.20.30.185      vKVM         yes
5      read-only        10.20.30.187      CLI          no

server#

This example shows how to display user session information about a specific user session:

server# show user-session 2
 
ID     Name             IP Address        Type         Killable 
------ ---------------- ----------------- ------------ -------- 
2      admin            10.20.30.185      vKVM         yes      

server#

Related Commands

Command

Description

show user

 

show version

To display the version number of the running firmware, use the show version command.

show version [ detail ]

Syntax Description

detail

(Optional) Displays the version number of the running firmware in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display the version of the running firmware:

server# show version

Firmware Version     
-------------------- 
1.0(0.82)            

server# 

Related Commands

Command

Description

activate (firmware)

 

show vmedia

To display information about the status and configuration of virtual media, use the show vmedia command.

show vmedia [ detail ]

Syntax Description

detail

(Optional) Displays detailed information about the status and configuration of virtual media in list format.

Command Default

None

Command Modes

Root (server#)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to display information about the status and configuration of virtual media:

server# show vmedia

Encryption Enabled Active Sessions 
------------------ --------------- 
no                 0               

server# 

Related Commands

Command

Description

set encryption (vmedia)

 

start

To start the technical support process, use the start command.

start

This command has no arguments or keywords.

Command Default

None

Command Modes

Technical support (/cimc/tech-support)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to start the technical support process:

server# scope cimc
server /cimc # scope tech-support
server /cimc/tech-support # start 
Tech Support upload started.
server /cimc/tech-support # 

Related Commands

Command

Description

cancel

 

terminate (user-session)

To terminate a CLI session, use the terminate command in user-session mode.

terminate

This command has no arguments or keywords.

Command Default

None

Command Modes

User session (/user-session)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to terminate a CLI session:

server# scope user-session
server /user-session # terminate                                                                              

Related Commands

Command

Description

show user-session

 

top

To return to root mode from any other mode, use the top command.

top

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to enter root mode from log mode:

server /cimc/log # top
server#                                                                               

Related Commands

Command

Description

exit

 

update (firmware)

To update server firmware, use the update command.

update ip-address file-path

Syntax Description

ip-address

The IP address of the TFTP server. The format is X.X.X.X.

file-path

The path to the update file on the TFTP server.

Command Default

None

Command Modes

Firmware (/cimc/firmware)

Command History

Release Modification
1.0(1)

This command was introduced.

Examples

This example shows how to update server firmware:

server# scope cimc
server /cimc # scope firmware
server /cimc/firmware # update 209.165.200.225 //test/cimc66-78.bin
  <CR>  Press Enter key
Firmware update has started.
Please check the status using "show detail"
server /cimc/firmware #                                                                              

Related Commands

Command

Description

show cimc

 

show version

 

upload (certificate)

To upload a certificate, use the upload command in certificate mode.

This command has no arguments or keywords.

Command Default

None

Command Modes

Certificate (/certificate)

Command History

Release Modification
1.0(1x)

This command was introduced.

Examples

This example shows how to upload a certificate:

server# scope certificate
server /certificate # upload
Please paste your certificate here, when finished, press CTRL+D.
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server /certificate #                                                                               

Related Commands

Command

Description

generate-csr (certificate)

 

show certificate