MGX 8850 (PXM1E/PXM45), MGX 8950, and MGX 8830 Command Reference, Release 4
dbg-
Downloads: This chapterpdf (PDF - 456.0KB) The complete bookPDF (PDF - 8.16MB) | Feedback

dbgcon

Table Of Contents

dbgcon

dbgilmi

dbgpnni

dbgsntp

dclk

del

deladdr

deladdrs

delallusers

delapsln

delbert

delclksrc

delcon

delcons

delconsegep

delcontroller

delcug

del

delfltset

delimagrp

delimalnk

dellink

dellnloop

dellpback

delncdpclksrc

delnwnode

delpart

delparty

delpnni-node

delpnni-summary-addr

delpnport

delpnportacc

delport

delpref

delprfx

delred

delrscprtn

delsct

delsesn

delsigdiag

delslotlink

delsntprmtsvr

deltopolink

deltopond

deltrapmgr

deluser

diagdebug

disablesscop

dncon

dnimagrp

dnilmi

dnln

dnparty

dnpnport

dnport

downloadflash


dbgcon

Debug Connection—PXM45, PXM1E

The node-level dbgcon command enables or disables the SPVC (or SPVP) error log. You can enable the error log for a specific connection by specifying a port ID, VPI, and VCI. To see whether the connection error log is enabled, use the dspcons-dbg command.


Note This command can substantially increase CPU usage, so you should seriously consider whether its usage is safe in your circumstances. This potential is greater when all connections are included.


Syntax

dbgcon <enable | disable> [-port <portid> -vpi <vpi> -vci <vci>]

Syntax Description

enable | disable

Enter enable or disable to start or stop the SPVC log. Default: disabled.

-port

Enter -port followed by the value of the portid for the specific SPVC. The format of the PNNI physical port identifier can vary, as follows:

On a PXM45: slot:subslot.port:subport

On a PXM1E for UNI/NNI back card: slot:subslot.port:subport. On the UNI/NNI back card, the subslot is always 2, but the slot depends on the chassis, as follows:

In an MGX 8850 chassis, slot is always the logical slot 7.

In an MGX 8830 chassis, slot is always the logical slot 1.

On a PXM1E for a narrowband service module (NBSM): slot.port.

For more details, see the section, "PNNI Format," in "Introduction."

-vpi

Enter -vpi followed by the value of the vpi for the specific SPVC.
The range is 0-4095.

-vci

Enter -vci followed by the value of the vpi for the specific SPVC.
The range is 1-65535.


Related Commands

dspcons-dbg

Attributes

Log: no

State: active, standby

Privilege: SERVICE_GP


Example

Enable the SPVC log for the connection with port ID 9:1.8:8 and VPI/VCI100/100.

MGX8850.8.PXM.a > dbgcon enable -port 9:1.8:8 -vpi 100 -vci 100

dbgilmi

Debug ILMI—PXM45, PXM1E

Use dbgilmi to debug ILMI functionality (such as address registration or auto configuration).


Note VSI pass-through information is exchanged between only the controller (PPNI) and the switch.


Syntax

dbgilmi {enable | disable} [<portid>] [-log <vsi | func | minor | major | warning | error | dump | fatal | all>] [-dbg <vsi | func | minor | major | warning | error | dump | fatal | all>]

Syntax Description

enable | disable

Activate or de-activate ILMI debugging.

portid

The format of the PNNI physical port identifier can vary, as follows:

On a PXM45: slot:subslot.port:subport

On a PXM1E for UNI/NNI back card: slot:subslot.port:subport. On the UNI/NNI back card, the subslot is always 2, but the slot depends on the chassis, as follows:

In an MGX 8850 chassis, slot is always the logical slot 7.

In an MGX 8830 chassis, slot is always the logical slot 1.

On a PXM1E for a narrowband service module (NBSM): slot.port.

For more details, see the section, "PNNI Format," in "Introduction."

-log

If you type the optional keyword log, follow it with at least one of the following:

vsi
func
minor
major
warning
error
dump
fatal
all: log all

-dbg

If you type the optional keyword dbg, follow it with at least one of the following:

vsi
func
minor
major
warning
error
dump
fatal
all: dbg all


Attributes

Log: yes

State: active, standby

Privilege: SERVICE_GP


dbgpnni

Debug PNNI MessagesPXM45, PXM1E

The dbgpnni command lets you specify the types of debug messages that appear in the display of the dsppnni-dbg command.


Note The selections you make with this command can significantly affect network performance. The simultaneous dumping of multiple types of debug messages can increase the overhead more than incrementally as each type is added. Consider the options individually rather than simultaneously.


Syntax

dbgpnni [-all {on | off}] [-hello {on | off}] [-election {on | off}] [-nbr {on | off}] [-itf {on | off}] [-timer {on | off}] [-lgn {on | off}] [-spt {on | off}] [-nodereachability {on | off}] [-address {on | off}] [-itdb {on | off}] [-ra {on | off}] [-cp {on | off}] [-linkselection {on | off}]

Syntax Description

-all

Specify whether all types of debug message go to the console.

on: All types of debug message go to the console.
off: Only the debug message-types specified by the other dbgpnni parameters are active.

Default: none

-timer

Specify whether the timer debug messages go to the console.

on: The timer debug messages go to the console.
off: The timer debug messages do not go to the console.

Default: none

-hello

Specify whether the hello debug messages go to the console.

on: The hello debug messages go to the console.
off: The hello debug messages do not go to the console.

Default: none

-nbr

Specify whether the PNNI neighbor FSM debug messages go to the console.

on: The PNNI neighbor FSM messages go to the console.
off: The PNNI neighbor FSM debug messages do not go to the console.

Default: none

-election

Specify whether the PNNI PGL election debug messages go to the console.

on: The PNNI PGL election messages go to the console.
off: The PNNI PGL election debug messages do not go to the console.

Default: none

-nodereachability

Specify whether the debug messages about PNNI node reachability computation go to the console.

on: The PNNI node reachability computation messages go to the console.
off: The PNNI node reachability computation is not active

Default: none

-itf

Specify whether the interface FSM debug messages go to the console.

on: The interface FSM messages go to the console.
off: The interface FSM debug messages do not go to the console.

Default: none

-address

Specify whether the debug messages about the handling on addresses go to the console.

on: The debug handling on addresses is active
off: The debug handling on addresses is not active

Default: none

-lgn

Specify whether the logical group node debug messages go to the console.

on: The PNNI logical group node messages go to the console.
off: The PNNI logical group node debug messages do not go to the console.

Default: none

-itdb

Specify whether the debug messages about the handling on the internal topology database go to the console.

on: The debug messages for the internal topology database go to the console.
off: The debug messages for the internal topology database does not go to the console.

Default: none

-cp

Specify whether the control point debug messages go to the console.

on: The control point debug messages go to the console.
off: The control point debug messages do not go to the console.

Default: none

-spt

Specify whether the shortest path tree debug messages go to the console.

on: The shortest path tree debug messages go to the console.
off: The shortest path tree debug messages do not go to the console.

Default: none

-ra

Specify whether the route agent debug messages go to the console.

on: The route agent debug messages go to the console.
off: The route agent debug messages do not go to the console.

Default: none.

-linkselection

Specify whether the link selection debug messages go to the console.

on: The link selection debug messages go to the console.
off: The link selection debug messages do not go to the console.

Default: none


Related Commands

dsppnni-dbg

Attributes

Log: yes

State: active

Privilege: CISCO_GP


Example

Specify the following PNNI debug message-options:

Interface debugging is enabled.

Address handling debugging is enabled.

Use dsppnni-dbg to check which debug messages types appear on the terminal.

SanJose.7.PXM.a > dsppnni-dbg
pnni debugging option:

hello   election   nbr   itf   timer   lgn   spt   node reachability
-----   --------   ---   ---   -----   ---   ---   -----------------
off     off        off   off   off     off   off   off

address   itdb   ra    cp    link selection
-------   ----   ---   ---   --------------
off       off    off   off   off


SanJose.7.PXM.a > dbgpnni -itf on -address on


SanJose.7.PXM.a > dsppnni-dbg
pnni debugging option:

hello   election   nbr   itf   timer   lgn   spt   node reachability
-----   --------   ---   ---   -----   ---   ---   -----------------
off     off        off   on    off     off   off   off

address   itdb   ra    cp    link selection
-------   ----   ---   ---   --------------
on        off    off   off   off

In the second example, the parameters are changed as follows:

Interface debugging is disabled.

Address handling debugging is disabled.

SanJose.7.PXM.a > dbgpnni -itf off -address off

SanJose.7.PXM.a > dsppnni-dbg
pnni debugging option:

hello   election   nbr   itf   timer   lgn   spt   node reachability
-----   --------   ---   ---   -----   ---   ---   -----------------
off     off        off   off    off     off   off   off

address   itdb   ra    cp    link selection
-------   ----   ---   ---   --------------
off       off    off   off   off

dbgsntp

Debug Simple Network Time Protocol—PXM45, PXM1E

The dbgsntp command lets you enable SNTP debugging and specify the level of debugging. Use the dspsntp-dbg command to see the debugging configuration created with the dbgsntp command.

Syntax

dbgsntp <enable | disable> [ipaddr] [-level <info | trace | debug>]

Syntax Description

enable or

disable

Type the "enable" to "disable" either to enable or to disable SNTP debugging.

Default: disable

ipaddr

Enter the IP address of a particular switch to debug SNTP between the current switch and the other switch.

-level

You can specify a level of debugging by entering one of the following:

info means informational only.

trace means a trace is sent.

debug means that detailed debugging is enabled.

Default: info


Related Commands

cnfsntp, cnfsntprmtsvr, dspsntp, dspsntprmtsvr, addsntprmtsvr, delsntprmtsvr, dspsntpstats

Attributes

Log: yes

State: active

Privilege: ANYUSER


Example

dclk

Display Clock Measured by System Clock Test—PXM45, PXM1E

Display the Digital to Analog Converter (DAC) value and the deviation, in parts-per-million, of the output frequency of the current clock source. This is the nominal frequency value for the local oscillator on the PXM45 UIS3 card.

The local oscillator of the UIS3 is an Over-Controlled Crystal Oscillator (OCXO) with a nominal frequency of 19.44Mhz. The control voltage applied to the OCXO by the hardware circuitry on the board adjusts the output frequency range of the clock between +/- 7 PPM (136Hz) to +/- 14PPM (272Hz).

The DAC value is used to convert the digital voltage value, from the DSP FPGA, to the analog voltage, which controls the OCXO. The range of the input DAC value is from 0x0000 to 0xffff with a nominal value of 0x8000.

The dclk output displays the DAC value field, which is the difference between the current measured DAC value and the nominal DAC value of 0x8000, and the PPM values for the last 100 current clock samples that have been taken at the rate of one every second.

Syntax

dclk

Syntax Description

This command takes no parameters.

Related Commands

None

Attributes

Log: no

State: active

Privilege: SERVICE_GP


Example

M8850_NY.7.PXM.a > dclk
    Sample        DAC   Dev ppm. 
      1         -900      -0.19
      2         -915      -0.19
      3         -915      -0.19
      4         -915      -0.19
      5         -900      -0.19
      6         -900      -0.19
      7         -916      -0.19
      8         -916      -0.19
      9         -916      -0.19
     10         -916      -0.19
     11         -916      -0.19
     12         -916      -0.19
     13         -900      -0.19
     14         -900      -0.19
     15         -899      -0.19
     16         -899      -0.19
     17         -899      -0.19
     18         -900      -0.19
     19         -900      -0.19
     20         -900      -0.19
     21         -899      -0.19
     22         -899      -0.19
     23         -900      -0.19
     24         -916      -0.19
     25         -899      -0.19
     26         -915      -0.19
     27         -915      -0.19
     28         -916      -0.19
     29         -900      -0.19
     30         -916      -0.19
     31         -916      -0.19
     32         -915      -0.19
     33         -915      -0.19
     34         -916      -0.19
     35         -916      -0.19
     36         -916      -0.19
     37         -900      -0.19
     38         -899      -0.19
     39         -900      -0.19
     40         -900      -0.19
     41         -900      -0.19
     42         -900      -0.19
     43         -915      -0.19
     44         -915      -0.19
     45         -916      -0.19
     46         -916      -0.19
     47         -915      -0.19
     48         -916      -0.19

del

Delete—PXM45, PXM1E

Use del to remove a file or directory from the PXM hard drive.

Syntax

del <path_name>

Syntax Description

path_name

Name of an existing file or directory.


Related Commands

delete, ll

Attributes

Log: log

State: active, standby, init

Privilege: GROUP1


deladdr

Delete Address—PXM45, PXM1E

Removes an ATM address for a UNI or IISP.

Syntax

deladdr <portid> <atm-address> <length> [-plan {e164 | nsap}]

Syntax Description

portid

The format of the PNNI physical port identifier can vary, as follows:

On a PXM45: slot:subslot.port:subport

On a PXM1E for UNI/NNI back card: slot:subslot.port:subport. On the UNI/NNI back card, the subslot is always 2, but the slot depends on the chassis, as follows:

In an MGX 8850 chassis, slot is always the logical slot 7.

In an MGX 8830 chassis, slot is always the logical slot 1.

On a PXM1E for a narrowband service module (NBSM): slot.port.

For more details, see the section, "PNNI Format," in "Introduction."

atm-address

The ATM address: its format depends on whether the address type is NSAP or E.164. The address plan specifies the address type and so determines the maximum number of bytes or bits in the address. You can specify the address plan with the forthcoming -plan option. The default plan is NSAP.

An NSAP address can have 1-20, 8-bit bytes (where a byte is 2 hexadecimal characters). Cisco recommends that you use 20 bytes for the NSAP address.

An E.164 address can 8-15 decimal digits.

The number of bits or bytes in the ATM address effects the uniqueness of the address. The longest address ensures total uniqueness of the address. With a one-byte address, any caller that sends an address whose first address byte matches that one-byte ATM address goes to that port.

length

Address length. The units of measure differ for each address plan. The -plan option lets you specify E.164 or NSAP.

For an NSAP address plan, the units of measure are bits. The range is 0-160. Using the maximum of a 20-byte address: 20 bytes x 8 bits per byte = 160 bits.

For an E.164 address plan, the value is the number of decimal digits. If the ATM address consists of 15 digits, the value for this parameter is also 15.

-plan

Address plan: E.164 or NSAP.

Default: nsap


Related Commands

addaddr, dspaddr, deladdrs

Attributes

Log: yes

State: active

Privilege: GROUP1


Example

On port 11:2.8:22, delete 47.0091.8100.0000.0000.0ca7.9e01.4000.0c81.8000.00. Note that the command entry includes the address length of 160 after the address.

Geneva.7.PXM.a > deladdr 11:2.8:28 47.0091.8100.0000.0000.0ca7.9e01.4000.0c81.8000.00 160

deladdrs

Delete Addresses—PXM45, PXM1E

Removes all ATM addresses on a UNI, AINI, or IISP. The optional plan parameter lets you differentiate by address plan:

E164

NSAP

All address plans (the default)

Syntax

deladdrs <portid> [-plan {e164 | nsap | all}]

Syntax Description

portid

The format of the PNNI physical port identifier can vary, as follows:

On a PXM45: slot:subslot.port:subport

On a PXM1E for UNI/NNI back card: slot:subslot.port:subport. On the UNI/NNI back card, the subslot is always 2, but the slot depends on the chassis, as follows:

In an MGX 8850 chassis, slot is always the logical slot 7.

In an MGX 8830 chassis, slot is always the logical slot 1.

On a PXM1E for a narrowband service module (NBSM): slot.port.

For more details, see the section, "PNNI Format," in "Introduction."

-plan

Address plan: E.164, NSAP, or all.

Default: all


Related Commands

addaddr, dspaddr, deladdr

Attributes

Log: yes

State: active

Privilege: GROUP1


Example

On port 11:2.8:22, delete all the addresses (regardless of address plan).

Geneva.7.PXM.a > deladdrs 11:2.8:28

delallusers

Delete All Users—PXM45, PXM1E

Use the delallusers command to delete every user account except the default user.

Syntax

delallusers

Syntax Description

This command takes no parameters, but the system prompts for confirmation (see Example).

Related Commands

adduser, dspusers, deluser, users

Attributes

Log: yes

State: active

Privilege: CISCO_GP


Example

Before you use the delallusers command, check the existing user accounts by using the dspusers command to be sure that deleting all users except the defaults is appropriate. Check the list of users after you run the delallusers command.

Delete all users except the default user.

Unknown.7.PXM.a > dspusers

    UserId        AccessLevel
    -------------------------
    cisco         CISCO_GP
    service       SERVICE_GP
    superuser     SUPER_GP
    david         GROUP1

Unknown.7.PXM.a > delallusers

This command deletes all users except the default users

delallusers:Do you want to proceed (Yes/No)? y

Unknown.7.PXM.a > dspusers

    UserId        AccessLevel
    -------------------------
    cisco         CISCO_GP
    service       SERVICE_GP
    superuser     SUPER_GP

delapsln

Delete APS Line—PXM45, PXM1E

The delapsln command removes the APS configuration from a line. See the addapsln description for information on Automatic Protection Switching (APS).

Syntax

delapsln <workingline>

Syntax Description

workingline

The working line has the following format:

slot.bay.line

The slot number depends on both the chassis and the card type, as follows:

For PXM45 in an MGX 8850 chassis, slot is 15 or 31.

For PXM1E in an MGX 8850 chassis:

For the UNI/NNI back card, slot is 7.

For the SRME, slot is 15 or 31.

For PXM1E in an MGX 8830 chassis:

For the UNI/NNI back card, slot is 1.

For the SRME, slot is 7.

The bay number is present only for consistency with legacy purposes (the slot number uniquely identifies the location of the card) The bay is a fixed logical number that depends on the card, as follows:

For SRME, bay always is 1.

For the PXM1E interface, bay always is 2.

The line number on the PXM1E OC3c/STM1 back card depends on the card type, as follows:

9-12 on the combo card

1-4 on the regular, 4-line card

1-8 on the regular, 8-line card

For an SRME, the line number always is 1.


Related Commands

addapsln, cnfapsln, dspapsln, switchapsln, dspapsbkplane, clrbecnt, dspbecnt

Attributes

Log: yes

State: active

Privilege: GROUP1


Example

Delete APS from line 1 of the PXM1E.

delapsln 7.2.1

delbert

Delete Bit Error Rate Test—PXM45, PXM1E

The delbert command lets you terminate a BERT session. This command applies to service modules that do not have native BERT capability and so require a Service Resource Module (SRM-3T3/C or SRME). An alternative to this command is the cnfbert command but with the enable parameter set to "destroy BERT." See cnfbert syntax description.

Syntax

delbert <LSMSlot.Line.Port>

Syntax Description

LSMSlot.Line.Port

The fields in the parameter can have the following values:

LSMslot can have a value in one of the following ranges: 1-6, 9-14, 17-22, or 25-30.

Line has a range from 1 though the maximum number of lines on the card.

The Port has a value from 1 though the maximum ports supported by the service module.


Related Commands

cnfbert, dspbert, dspbertcap

Attributes

Log: yes

State: active

Privilege: GROUP1


delclksrc

Delete Clock Source—PXM45, PXM1E

Deletes a user-specified primary or secondary clock source. This command applies on switches that have a manual clock configuration. (See also cnfclksrc and cnfncdp descriptions.) Changing a clock source or changing the priority of the source (primary or secondary) are the most frequent uses of delclksrc. See the description of cnfclksrc for these common uses of delclksrc.


Note If the node has a redundant PXM, it automatically receives changes to the clock configuration as well as automated changes to clock status that occur under node management. For example, executing delclksrc is a configuration change that the standby card automatically implements. Also, a switch from primary to secondary clock source is recorded by the standby PXM.


Syntax

delclksrc <priority>

Related Commands

cnfclksrc, dspclksrcs, dspclkalms

Attributes

Log: yes

State: active

Privilege: SUPER_GP


Example

Delete the primary clock source.

pinnacle.7.PXM.a> delclksrc primary

delcon

Delete Connection—PXM1E

Use the delcon command to delete an SPVC or SPVP. Note the variations for this command:

For dual-ended connections, delete the connection at both ends—at the master end first.

To delete a single-ended connection, use this command at the master end only.

To delete a point-to-multipoint (P2MP) connection, all parties must be deleted from the connection before you can delete the connection (see the delparty description). For a P2MP connection, use this command at the master end only

Syntax

delcon <ifnum> <vpi> <vci>

Syntax Description

ifnum

The range for logical interface (or port) numbers is are as follows 1-31.

vpi

Virtual path identifier in the range 0-255 (UNI) or 0-4095 (NNI or VNNI).

vci

Virtual connection identifier (VCI):

For a VCC on a UNI, the range is 1-4095. On an NNI or VNNI, the VCI range is 1-65535. For MPLS, the recommended minimum VCI is 35.

For a VPC, the vci is 0.


Related Commands

dspcon, addcon, cnfcon

Attributes

Log: yes

State: active

Privilege: GROUP1


Example

MGX8850.7.pxm1e.a > delcon 1 10 40
Deletion successful

delcons

Delete Connections—PXM1E

Delete a range of connections.


Caution The delcons command is intended for Cisco development engineers to use during the troubleshooting of system software. This command is too dangerous to use in user networks carrying live traffic because it can delete far more than the anticipated number of connections result in costly damage.

Syntax

delcons <ifNum> <vpi> <vci> [-num <num. conns to del>] [-verbose < 1 | 0 >]

Syntax Description

ifNum

The range for logical interface (or port) numbers is are as follows 1-31.

vpi

For a UNI, the range is 0-255. For an NNI, the range is 0-4095.

vci

For a VCC, the range is 1-65535. For a VPC, the only value is 0.

-num

(Optional) Keyword that specifies the number of connections to delete.

-verbose

(Optional) Keyword that enables (1) or disables (0) verbose mode. In verbose mode, the screen displays the connection identifier of each connection immediately after it is deleted.


Related Commands

None

Attributes

Log: no

State: active

Privilege: SERVICE_GP


delconsegep

Delete Connection Segment Endpoint—PXM45, PXM1E

Deletes a segment endpoint on a connection. When both VPI and VCI are present, the segment endpoint is an F5 flow endpoint (for VCCs). When the optional VCI is not present, the segment endpoint is an F4 flow endpoint (for VPCs).


Note The delconsegep command works for SVCs only.


Syntax

delconsegep <portid> <vpi> [vci]

Syntax Description

portid

The format of the PNNI physical port identifier can vary, as follows:

On a PXM45: slot:subslot.port:subport

On a PXM1E for UNI/NNI back card: slot:subslot.port:subport. On the UNI/NNI back card, the subslot is always 2, but the slot depends on the chassis, as follows:

In an MGX 8850 chassis, slot is always the logical slot 7.

In an MGX 8830 chassis, slot is always the logical slot 1.

On a PXM1E for a narrowband service module (NBSM): slot.port.

For more details, see the section, "PNNI Format," in "Introduction."

vpi

VPI of the connection.

vci

VCI of the connection.


Related Commands

cnfoamsegep, dspoamsegep, cnfconsegep, dspconsegep

Attributes

Log: yes

State: active

Privilege: GROUP1


delcontroller

Delete Controller—PXM45, PXM1E

Delete a controller. The delcontroller command does not erase the controller software but directs the switch not to use it.

Syntax

delcontroller <cntrlrId>

Syntax Description

cntrlrId

The controller ID (cntrlrId) has a range of 1-20 and is assigned using addcontroller. To see all controllers on the switch, use dspcontrollers.


Related Commands

addcontroller, dspcontrollers

Attributes

Log: yes

State: active

Privilege: SUPER_GP


Example

Delete controller 3. In this example, the 3 is the reserved controller ID for LSC.

MGX8850.8.PXM.a > delcontroller 3

delcug

Delete Closed User Group—PXM45, PXM1E

The delcug command lets you remove an ATM address (or member) from a closed user group (CUG). When a CUG has no more members, the system automatically deletes that CUG.

Syntax

delcug <atm-address> <length> <plan> <cug-index>

Syntax Description

atm-address

The NSAP or E.164 address on the local UNI interface is 20 bytes.

length

Address length. The units of measure differ for each address plan. The -plan option lets you specify E.164 or NSAP.

For an NSAP address plan, the units of measure are bits. The range is 0-160. Using the maximum of a 20-byte ATM address:

20 bytes x 8 bits per byte = 160 bits

For an E.164 address plan, the value is the number of decimal digits. If the ATM address consists of 15 digits, the value for this parameter is also 15.

plan

The plan is either NSAP or E.164 and is set when you add the ATM address by using the addaddr command.

cug-index

The cug-index uniquely identifies this closed user group on the ATM address. The maximum number of CUG indexes you can assign to an ATM address is 100.

Range: 1-65535


Related Commands

addcug, cnfcug, clrcugdefaddr, cnfaddrcug, cnfnodecug, dspaddrcug, dspcug, dspcugdefaddr, dspnodecug, setcugdefaddr

Attributes

log: yes

State: active

Privilege: SUPER_GP


Example

For CUG 12, delete the member with address 47.0091.8100.0000.0001.5555 (length 88 and NSAP plan).

Geneva.7.PXM.a > delcug 47.0091.8100.0000.0001.5555 88 nsap 12

del

Delete—PXM45, PXM1E

Use delete to remove a file or directory from the PXM hard drive.

Syntax

delete <path_name>

Syntax Description

path_name

Name of an existing file or directory.


Related Commands

del, ll

Attributes

Log: log

State: active, standby, init

Privilege: GROUP1


delfltset

Delete Filter Set—PXM45, PXM1E

Removes an ATM address filter set.

Syntax

delfltset <name> [index]

Syntax Description

name

The name of the filter set.

index

Delete a specific filter element.

Range: 1-65535
Default: 0


Related Commands

addfltset, cnffltset, dspfltset

Attributes

Log: yes

State: active

Privilege: GROUP1


Example

Remove the "connect" filter set from the port.

Geneva.7.PXM.a > delfltset connect

delimagrp

Delete IMA Group—PXM1E

This command deletes an IMA group.

Syntax

delimagrp <group>

Syntax Description

group

The group identifier consists of a bay number as well as a group number in the format bay.group, as follows:

bay: always 2 on the PXM1E

group: 1-16


Related Commands

addimagrp, dspimagrp, dspimagrps, cnfimagrp, rstimagrp

Attributes

Log: yes

State: active

Privilege: ANYUSER


Example

Delete IMA group 6.

MGX8850.7.PXM1E.a > delimagrp 2.6

delimalnk

Delete IMA Link—PXM1E

This command deletes a link from an IMA group.

Syntax

delimalnk <link>

Syntax Description

link

The link to be deleted, specified as bay.ds1.

bay: always 2

ds1: 1-16


Related Commands

dspimagrp, cnfimagrp, rstimagrp, dspimalnk, addimalnk

Attributes

Log: yes

State: active

Privilege: GROUP1


Example

Delete link 16.

MGX8850.7.PXM1E.a > delimalnk 2.16

dellink

Delete Link—PXM45, PXM1E

The dellink command lets you remove a link. A link is part of the bulk distribution feature on the SRM-3T3 and SRM-E. See the addlink description for information on bulk mode distribution.

Syntax

dellink <SrmStartLinkIf>

Syntax Description

SrmStartLinkIf

The format for SrmStartLinkIf is slot.line.link. The SrmStartLinkIf parameter identifies physical and logical elements of the SRM. The slot is logical and refers to the primary SRM slots as well as the standby slots. The physical line is one of three T3s on an SRM-3T3 or an OC3/STM1 on an SRME. The link is the starting T1 or E1 tributary that you intend to make up the link. When planning the link mapping, keep track of the starting tributary. The ranges are as follows:

The slot is the logical slot depends on the chassis, as follows:

In an MGX 8850 chassis, slot can be either 15 or 31.

In an MGX 8830 chassis, slot is 7.

The line has the following possible ranges:

For SRM-E, line is 1.

For SRM-3T3, line has a range of 1-3.

The range for link depends firstly on the SRM front card and secondly on the tributary type, as follows.

For SRM-3T3, line has a range of 1-28.

For SRM-E and tributary type T1, line has a range of 1-84.

For SRM-E and tributary type E1, line has a range of 1-63.


Related Commands

addlink, cnflink, dsplink

Attributes

Log: yes

State: active

Privilege: GROUP1


Example

dellnloop

Delete Line Loop—PXM45, PXM1E

Remove the line loopback state from a line.

Syntax

dellnloop < -ds3 | -e3 | -sonet | -ds1 | -e1 > <bay.line>

Syntax Description

-ds3
-e3
-sonet
-ds1
-e1

Specifies a DS3, E3, T3, SONET (OC-3c), DS1, or E1 line.

bay.line

The bay is always 2. The line number can be 1 to the highest line on the back card.


Related Commands

addlnloop

Attributes

Log: yes

State: active

Privilege: GROUP1


Example

Deleting a DS3 loopback line.

MGX8850.1.7.PXM1E.a > dellnloop -ds3 2.6 -lpb 3
Line loop-back status will be changed.
Do you want to proceed (Yes/No)?

dellpback

Delete Loopback—PXM45, PXM1E

The addlpback command lets you delete a specific loopback that is running on a service module.

Syntax

dellpback <LSMSlot.Line.Port> <loopbackType> <loopbackCode>

Syntax Description

LSMSlot.Line.Port

The fields in the parameter can have the following values:

LSMslot can have a value in one of the following ranges: 1-6, 9-14, 17-22, or 25-30.

Line has a range from 1 though the maximum number of lines on the card.

The Port has a value from 1 though the maximum ports supported by the service module.

loopbackType

To select a loopback type, enter the number that corresponds to the loopback.

Note In the current release, the SRME does not support payload loopback types.

1: farEndLineLoopback

2: farEndPayloadLoopback

3: remoteLineLoopback

4: remotePayloadLoopback

5: localLoopback


loopbackCode

To select a loopback code, type the number that corresponds to the code.

1: nonLatchOCUwith1

2: nonLatchOCUwithout1

3: nonLatchCSU

4: nonLatchDSU

5: latchDS0Drop

6: latchDS0Line

7: latchOCU

8: latchCSU

9: latchDSU

10: latchHL96

11: v54PN127Polynomial

12: lineInband

13: lineLoopbackESF

14: payloadLoopbackESF

15: noCode

16: lineLoopbackFEAC

17: SmartJackInband


Related Commands

addlpback, dspbertcap

Attributes

Log: yes

State: active

Privilege: GROUP1


delncdpclksrc

Delete NCDP Clock Source—PXM45, PXM1E

The delncdpclksrc command lets you delete an NCDP clock source. See the cnfncdp description for details on the Network Clock Distribution Protocol (NCDP).

Syntax

delncdpclksrc <portID> [clocktype <e1 | t1>]

Syntax Description

portid

The format of the PNNI physical port identifier can vary, as follows:

On a PXM45: slot:subslot.port:subport

On a PXM1E for UNI/NNI back card: slot:subslot.port:subport. On the UNI/NNI back card, the subslot is always 2, but the slot depends on the chassis, as follows:

In an MGX 8850 chassis, slot is always the logical slot 7.

In an MGX 8830 chassis, slot is always the logical slot 1.

On a PXM1E for a narrowband service module (NBSM): slot.port.

For BITS clocks only, portid can be 7.35 or 7.36 in an MGX 8850. In an MGX 8830 chassis, the portid for BITS is either 1.35 or 1.36.

For more details, see the section, "PNNI Format," in "Introduction."

clocktype

Enter e1 or t1 as needed when the port ID is one of the following:

7.35 or 7.36 in an MGX 8950 or MGX 8850 chassis

1.35 or 1.36 in an MGX 8830 chassis

If the clock type is the default E1, this parameter is not necessary for port IDs 7.35 or 7.36 (or 1.35.or 1.36).

Default: e1


Related Commands

cnfncdp, cnfncdpclksrc, cnfncdpport, dspncdp, dspncdpclksrc, dspncdpclksrcs, dspncdpport, dspncdpports

Attributes

Log: yes

State: active

Privilege: SUPER_GP


delnwnode

Delete Network Node—PXM45, PXM1E

The delnwnode command deletes a particular node from the network node table. The purpose of this command is to support the Preferred Route feature. See the addpref description for details about the Preferred Route feature.

The delnwnode command takes a node ID as its only parameter. If you do not have the node ID, you can see all nodes in the table by using the dspnwnodes command. If you have only a node's name, you can obtain its node ID by using the dspnwnode command.

Syntax

delnwnode <nodeId>

Syntax Description

nodeId

The nodeId is the 22-octet PNNI node identifier.


Related Commands

addnwnode, dspnwnode, dspnwnodes, addpref

Attributes

Log: yes

State: active

Privilege: SUPER_GP


Example

Delete the entry for the network node with the ID 56:160:47.00918100000000c043002ddf.00c043002ddf.01.

pswpop10.7.PXM.a > delnwnode 56:160:47.00918100000000c043002ddf.00c043002ddf.01

delpart

Delete Resource Partition—PXM1E


Note The delpart and delrscprtn commands are identical. The name `delrscprtn' is consistent with the corresponding command in Release 1 of the MGX 8850 switch. You can use either command.


Syntax

delpart <if_num> <part_id>

Syntax Description

if_num

The range for logical interface (or port) numbers is are as follows 1-31.

part_id

The partition ID number in the range 1-20. Use dspparts (or dsprscprtns) to see all resource partitions if necessary.


Related Commands

addpart, cnfpart, dsppart

Attributes

Log: yes

State: active

Privilege: GROUP1


Example

MGX8850.7.PXM1E.a > delpart 1 1

delparty

Delete Party—PXM45, PXM1E

The delparty commands deletes a party from a point-to-multipoint SPVC or SPVP at the master endpoint.

Syntax

delparty portid vpi vci endpointRef

Syntax Description

portid

The format of the PNNI physical port identifier can vary, as follows:

On a PXM45: slot:subslot.port:subport

On a PXM1E for UNI/NNI back card: slot:subslot.port:subport. On the UNI/NNI back card, the subslot is always 2, but the slot depends on the chassis, as follows:

In an MGX 8850 chassis, slot is always the logical slot 7.

In an MGX 8830 chassis, slot is always the logical slot 1.

On a PXM1E for a narrowband service module (NBSM): slot.port.

For more details, see the section, "PNNI Format," in "Introduction."

vpi

The local VPI of the connection is in one of the following ranges:

UNI: 0-255

NNI: 0-4095

vci

The local VCI of the connection has a range of 35-65535.

endpointRef

The endpoint reference has a range of 1-32767


Related Commands

addcon, rrtparty, dnparty, upparty, addparty, dspparty, dspparties, dsppartiespercon, dspcon, dspcons, dsppnport, dsppnports, clrspvcnonpers

Attributes

Log: yes

State: active

Privilege: GROUP1


Example

delpnni-node

Delete PNNI Node—PXM45, PXM1E

The delpnni-node command removes a PNNI node from the PNNI network topology. A node that this command deletes can be restored with the related command addpnni-node. Confirm the deletion of nodes with the dsppnni-node command.

Syntax

delpnni-node <node-index>

Syntax Description

node-index

The node index indicates the relative level of the logical node within a multi-peer group on the switch. The range is 1-10, and the lowest level is 1.

Range: 1-10
Default: 1


Related Commands

addpnni-node, cnfpnni-node, delpnni-node

Attributes

Log: yes

State: active

Privilege: SUPER_GP


Example

Delete the node with the node-index of 3. Execute dsppnni-node and specify a node index of 3. The last line of the d display shows the error "node does not exist," indicating you successfully deleted the node.

SanJose.7.PXM.a > delpnni-node 3

SanJose.7.PXM.a > dsppnni-node 3 

   Unknown Error Code
Syntax: dsppnni-node [node-index]

        nodeIndex -- node-index: 32 bit number starting from 1, Optional parameter

        possible errors are:
node does not exist

SanJose.7.PXM.a > 

delpnni-summary-addr

Delete PNNI Summary AddressPXM45, PXM1E

The delpnni-summary-addr command deletes a PNNI summary address for a PNNI node.

Syntax

delpnni-summary-addr <node-index> <address-prefix> <prefix-length>

Syntax Description

node-index

The node index indicates the relative level of the logical node within a multi-peer group on the switch. The range is 1-10, and the lowest level is 1.

Range: 1-10
Default: 1

address-prefix

The PNNI summary address.

Default: none

prefix-length

The length of the address-prefix in bits is less than or equal to 152.

Default: none


Related Commands

addpnni-summary-addr, dsppnni-summary-addr

Attributes

Log: yes

State: active

Privilege: SUPER_GP


Example

Delete a summary address, as follows:

The node-index is 1.

The node address prefix is 47.0091.8100.0000.0030.9409.f1f1.

The length of the address prefix is 104 bits.

If necessary, use dsppnni-summary-addr to confirm the deletion.

SanJose.7.PXM.a > delpnni-summary-addr 1 47.0091.8100.0000.0030.9409.f1f1 104

SanJose.7.PXM.a > 

delpnport

Delete PNNI Port—PXM45, PXM1E

The delpnport command lets you remove a UNI or NNI port from the controller. It is allowed only if the PNNI port does not exist on the switch i.e, the PNNI partition associated with the port is removed. If the controller does no provisioning on the port in the Plug and Play Scenario, then the PNNI port on the controller is removed if you remove the PNNI Partition on the switch.

Syntax

delpnport <portid>

Syntax Description

portid

The format of the PNNI physical port identifier can vary, as follows:

On a PXM45: slot:subslot.port:subport

On a PXM1E for UNI/NNI back card: slot:subslot.port:subport. On the UNI/NNI back card, the subslot is always 2, but the slot depends on the chassis, as follows:

In an MGX 8850 chassis, slot is always the logical slot 7.

In an MGX 8830 chassis, slot is always the logical slot 1.

On a PXM1E for a narrowband service module (NBSM): slot.port.

For more details, see the section, "PNNI Format," in "Introduction."


Related Commands

addpnport, uppnport, dnpnport, dsppnport

Attributes

Log: yes

State: active

Privilege: GROUP1


Example

Delete port 11:2.8:28 from the switch.

Geneva.7.PXM.a > delpnport 11:2.8:28 

delpnportacc

Delete Port Access—PXM45, PXM1E

Removes an address access filter group from a port.

Syntax

delpnportacc <portid> {in | out}

Syntax Description

portid

The format of the PNNI physical port identifier can vary, as follows:

On a PXM45: slot:subslot.port:subport

On a PXM1E for UNI/NNI back card: slot:subslot.port:subport. On the UNI/NNI back card, the subslot is always 2, but the slot depends on the chassis, as follows:

In an MGX 8850 chassis, slot is always the logical slot 7.

In an MGX 8830 chassis, slot is always the logical slot 1.

On a PXM1E for a narrowband service module (NBSM): slot.port.

For more details, see the section, "PNNI Format," in "Introduction."

in

Delete incoming access group for the port.

out

Delete outgoing access group for the port.


Related Commands

cnfpnportacc

Attributes

Log: yes

State: active

Privilege: GROUP1


Example

Delete the filter group for incoming calls from port 11:2.8:28.

Geneva.7.PXM.a > delpnportacc 11:2.8:28 in

delport

Delete Port—PXM1E

Remove a logical port from a service module. You must delete all connections and resource partitions on the port before you can delete it.

Syntax

delport <ifNum>

Syntax Description

ifNum

The range for logical interface (or port) numbers is are as follows 1-31.


Related Commands

addport, cnfport, dspport, dspports

Attributes

Log: yes

State: active

Privilege: GROUP1


delpref

Delete Preferred Route—PXM45, PXM1E

The delpref command lets you delete a preferred route. No connections can have the preferred route associated with them before you delete the route. To see if a route is associated with any connections, run the dspcons command with the -rteid filter and the ID of the route you intend to delete. This information is not available through SNMP. For detailed information about preferred routes, see the addpref description.

Syntax

delpref <route-id>

Syntax Description

route-id

The route-id identifies the preferred route.

Range: 1-65535

Default: none


Related Commands

addpref, cnfpref, dsppref, dspprefs, dspcons

Attributes

Log: yes

State: active

Privilege: GROUP1


Example

delprfx

Delete Prefix—PXM45, PXM1E

The delprfx command lets you delete an ILMI address prefix associated with a UNI, IISP, or AINI.

Syntax

delprfx <portid> <atm-prefix>

Syntax Description

portid

The format of the PNNI physical port identifier can vary, as follows:

On a PXM45: slot:subslot.port:subport

On a PXM1E for UNI/NNI back card: slot:subslot.port:subport. On the UNI/NNI back card, the subslot is always 2, but the slot depends on the chassis, as follows:

In an MGX 8850 chassis, slot is always the logical slot 7.

In an MGX 8830 chassis, slot is always the logical slot 1.

On a PXM1E for a narrowband service module (NBSM): slot.port.

For more details, see the section, "PNNI Format," in "Introduction."

atm-prefix

A 13-byte ATM address prefix, specified as 26 hexadecimal characters.


Related Commands

addprfx, dspprfx

Attributes

Log: yes

State: active

Privilege: GROUP1


Examples

Delete ATM prefix 47.0091.8100.0000.0000.0ca7.9e01 from PNNI physical port 3:1.1:1. Display prefixes for this port.

M8850_NY.7.PXM.a > delprfx 3:1.1:1 47.0091.8100.0000.0000.0ca7.9e01

M8850_NY.7.PXM.a > dspprfx 3:1.1:1

INFO: No Prefix registered

M8850_NY.7.PXM.a > 

delred

Delete Redundancy—PXM45, PXM1E

The delred command lets you delete the redundancy between a pair of card slots. It applies to 1:1 and 1:N redundancy.


Note 1:N redundancy requires a Service Resource Module (SRM-3T3/C or SRME) in the switch.


The higher speed cards support only 1:1 redundancy. The T1 and E1 service modules can have 1:N redundancy provided by an SRM. When you delete redundancy, the switch resets the primary card.

Syntax

delred <redPrimarySlotNumber>

Syntax Description

redPrimarySlotNumber

The range of slot numbers for the primary depend on the node, as follows:

MGX 8950 node (PXM45): 1-6 and 11-16

MGX 8850 node (PXM45): 1-6 and 9-14

MGX 8850 node (PXM1E): 1-6, 9-14, 17-22, and 25-30

MGX 8830 node (PXM1E): 3-6 and 10-13


Related Commands

addred, dspred, switchredcd

delrscprtn

Delete Resource Partition—PXM1E

Delete a resource partition. Note that you must delete all connections in the resource partition before you delete it. For information on resource partitions, refer to the description of addrscprtn.

Syntax

delrscprtn <if_num> <part_id>

Syntax Description

if_num

The range for logical interface (port) numbers is 1-31.

part_id

The partition ID number in the range 1-20. Use dsprscprtns to see all resource partitions if necessary.


Related Commands

addrscprtn, dsprscprtns, delpart, addpart, dsppart

Attributes

Log: yes

State: active

Privilege: GROUP1


Example

MGX8850.7.PXM1E.a > delrscprtn 1 1

delsct

Delete Service Class Temple—PXM45, PXM1E

The delsct command completely removes a service class template (SCT) from the switch. For an SCT that already operates at the port or card level, this command has no immediate effect. The purpose of this command is to remove excess or unused SCTs.

Before the operation proceeds to completion, the system prompts you with a warning, as follows:


Note "Warning: this SCT may be in use on the service modules or the PXM1E. Please verify SCT usage on these cards by using the dspports command. After a reset, cards may revert to default SCT if the provisioned SCT is not found. Do you want to proceed (Yes/No)?"


Syntax

delsct <cardtype> <scttype> <sctid> <majorversion>

Syntax Description

-cardtype

The cardtype parameter is an integer that refers to one of the following:

1: AXSM

2: AXSM-E

3: PXM1E

4: FRSM12

-scttype

The scttype parameter identifies either a port-level or a card-level SCT, as follows:

1: Port-level SCT

2: Card-level SCT

Default: None

-sctid

The range is 1-65535.

Default: none

-majorversion

The range is 1-65535.

Default: none


Related Commands

addsct, cnfsct, dspscts, setsctver, addport, cnfport, dspport, cnfcdsct, dspportsct, dspcdsct, dspsct

Attributes

Log: yes

State: active

Privilege: GROUP1


Example

Delete port-level SCT 1 for AXSM card types. When prompted with a warning, abort the operation.

D1.7.PXM.a > delsct 1 1 1 1
Warning: this SCT may be in use on the service modules or the PXM1E. Please verify SCT 
usage on these cards by using the dspports command. After a reset, cards may revert to 
default SCT if the provisioned SCT is not found.
Do you want to proceed (Yes/No)? n
(command not executed)

delsesn

Delete Session—PXM45, PXM1E

The delsesn command lets you terminate one or more user-sessions. To see the number of the each active session, use the dspsesn command. Termination takes place immediately upon command execution. Before it proceeds, the CLI warns you that the command is destructive. If you proceed with the deletion, the user whose session is being deleted receives the message, "Forced Logout By <userid> !!!!!!!!!!!," where userid is the user running the delsesn command. Note that you can delete any user-session with this command.

Syntax

delsesn {<sesn no> | <sesn no> <sesn no> .... | all}

Syntax Description

sesn no

The session number has a range of 1-15. You can specify one session, a series of user sessions, or all user sessions. The dspsesn command displays the user-session numbers.


Related Commands

dspsesn, who

Attributes

Log: yes

State: active, standby, init

Privilege: SERVICE_GP


Example

Use the dspsesn command to determine the existing user-sessions. Delete session 2 (user "david9"), then repeat the dspsesn command. Note that the dspsesn output provides a form of the user-session number that delsesn requires: "Session 2."

M8850_NY.7.PXM.a > M8850_NY.7.PXM.a > dspsesn

    Port        Slot      Idle       UserId       From
    -------------------------------------------------------------
    telnet.01 *    7     0:00:00     david        10.19.238.35
    telnet.02      7     0:00:18     david9       10.19.238.35

M8850_NY.7.PXM.a > M8850_NY.7.PXM.a > dspsesn

-----------------------------------------
 > Session 0 (console): 
Waiting for login...

-----------------------------------------
*> Session 1 (telnet): 
Executing command: dspsesn

user name:         david
access level:      SERVICE_GP
slot:              7
slotFallback:      1
From:              10.19.238.35

-----------------------------------------
 > Session 2 (telnet): 
Waiting for user input...

user name:         david9
access level:      GROUP1
slot:              7

slotFallback:      7
From:              10.19.238.35

M8850_NY.7.PXM.a > delsesn 2
WARNING! delsesn is a destructive command it will 
non-gracefully delete sessions selected by you 
Do you wish to proceed? [y/n] y

M8850_NY.7.PXM.a > dspsesn

-----------------------------------------
 > Session 0 (console): 
Waiting for login...

-----------------------------------------
*> Session 1 (telnet): 
Executing command: dspsesn

user name:         david
access level:      SERVICE_GP
slot:              7
slotFallback:      1
From:              10.19.238.35

delsigdiag

Delete Signaling Diagnostic—PXM45, PXM1E

The delsigdiag command lets you delete a portion of a signaling diagnostic filter table entry of the entire table entry (see Syntax Description.) For details on these filters, see the cnfsigdiag description.

Syntax

delsigdiag [index] [-cldaddr nsap-address] [-clgaddr nsap-address] [-cldaddrmask {yes | no}] [-clgaddrmask {yes | no}] [-casttype {yes | no}] [-clrcause {yes | no}] [-connctgy {yes | no}] [-inport {yes | no}] [-outport {yes | no}] [-maxrec {yes | no}] [-scope {yes | no}] [-servctgy {yes | no}] 

Syntax Description

index

Specifies the diagnostics index number for the filter table. If no other keywords are entered, the indexed filter table entry is deleted.

Range: 1-50

-cldaddr

Removes the configured called address from the filter entry.

-clgaddr

Removes the configured calling address from the filter entry.

-cldaddrmask

yes returns the called address mask to the default.

Default: no

-clgaddrmask

yes returns the calling address mask to the default.

Default: no

-casttype

yes to disable filtering by connection type.

Default: no

-clrcause

yes to disable filtering by the release cause code.

Default: no

-connctgy

yes returns the connection category to the default.

Default: no

-inport

yes returns the incoming port to the default.

Default: no

-outport

yes returns the outgoing port to the default.

Default: no

-maxrec

yes returns the maximum records to the default.

Default: no

-scope

yes to disable filtering by scope.

Default: no

-servctgy

yes returns the service category to the default.

Default: no


Related Commands

cnfsigdiag, delsigdiag, dspsigstats, clrsigstats

Attributes

Log: yes

State: active

Privilege: SERVICE_GP


delslotlink

Delete Slot Link—PXM45, PXM1E

The delslotlink command lets you delete either one link or all links between an SRM and a service module. See the addlink description for details on bulk mode distribution.

Syntax

delslotlink <SM SlotNum> < SM LineNum>

Syntax Description

SM SlotNum

The SM SlotNum parameter identifies the slot number of the service module. Possible entries depend on the chassis, as follows:

MGX 8850: 1-6, 9-14, 17-22, and 25-30

MGX 8830: 3-6 and 10-13

SM LineNum

The SM LineNum parameter identifies a particular line or all lines, as follows:

0: all links

1-8: the number of the individual line


Related Commands

addlink, cnflink, dsplink, dspslotlink

Attributes

Log: yes

State: active

Privilege: ANYUSER


delsntprmtsvr

Delete SNTP Remote Server-—PXM45, PXM1E

The delsntprmtsvr command lets you delete the role of a remote switch as an SNTP server. Alternatively, you can delete all servers from the list of SNTP servers.

Syntax

delsntprmtsvr {server IP address} | all

Syntax Description

server IP address

all

Specify the IP address of one switch to remove it from the list of servers, or type "all" to clear the entire list of servers.


Related Commands

addsntprmtsvr, cnfsntprmtsvr, dspsntprmtsvr, dspsntp, cnfsntp

Attributes

Log: yes

State: active

Privilege: GROUP1


deltopolink

Delete Topology Link—PXM45, PXM1E

The deltopolink command deletes a link from the topology database. For a list of the link numbers, use the dsptopolinklist command.

When you delete a node from the persistent node database by using either CWM or the deltopond command, all the links that are associated with the deleted node are also deleted from the persistent link database. Also, if an inside link becomes an outside link in the common outside state, the entry belonging to the outside node is removed from the persistent topology database.

Syntax

deltopolink

Syntax Description

deltopolink <linkIndex>

Related Commands

cnftopogw, dsptopogw, dsptopogwndlist, dsptopondlist, dsptopolinklist

Attributes

Log: yes

State: active

Privilege: SUPER_GP


Example

deltopond

Delete Node From Persistent Topology Database—PXM45, PXM1E

The deltopond command deletes a single node from the persistent topology database.

When you delete a node from the persistent node database by using either CWM or the deltopond command, all the links that are associated with the deleted node are also deleted from the link persistent database.

Syntax

deltopond <nodeIndex>

Syntax Description

nodeIndex

Provide the current node's index to delete it from the persistent topology database. To see a list of all indexes and nodes, use the dsptopondlist command.


Related Command

cnftopogw, dsptopogw, dsptopogwndlist, dsptopondlist

Attributes

Log: yes

State: active

Privilege: SUPER_GP


deltrapmgr

Delete Trap Manager—PXM45, PXM1E

The deltrapmgr command lets you delete a trap manager. This command requires an IP address for deletion. To see existing trap managers, use dsptrapmgr.

For more information on trap managers, see the following documentation:

The document titled Cisco MGX 8850 (PXM1E/PXM45), Cisco MGX 8950, and Cisco MGX 8830 Software Configuration Guide, Release 4

The addtrapmgr description

Syntax

deltrapmgr <ip_addr>

Syntax Description

ip_addr

IP address in dotted decimal format:

nnn.nnn.nnn.nnn, n=0-9 and nnn < 256


Related Commands

addtrapmgr, dsptrapmgr

Attributes

Log: yes

State: active

Privilege: SUPER_GP


Example

Delete trap manager with IP address 161.10.144.56.

node501.7.PXM.a > deltrapmgr 161.10.144.56

deluser

Delete User—PXM45, PXM1E

Removes a user from the list of users on a node. The system does not allow you to delete a user with a privilege level higher than the level at which you execute the command. For example, if the current user privilege is 2 (GROUP2), you cannot delete a user at level 1 (GROUP1). See the adduser description for the user-privilege hierarchy. No screen output appears unless an error occurs.

Syntax

deluser <user ID>

Syntax Description

user ID

User name, consisting of up to 12 characters.


Related Commands

dspusers, adduser

Attributes

Log: yes

State: active

Privilege: GROUP1


diagdebug

Diagnostic Debug—PXM45, PXM1E

The diagdebug command lets you either display or modify diagnostic settings. These settings are not the tests themselves but rather the interface to the diagnostics. For example, you can select how verbose the output display should be. Note that this command is for debugging only.

The parameters for the diagdebug command let you select general tests types and specific tests. For information on diagnostic tests, see the cnfdiag description.

Syntax

diagdebug <option> [<arg>]

Syntax Description

option

The range for the option parameter is 1-7. The argument numbers and definitions follow each option number:

1 Display system diag parameters

arg = 1 - System Diag parameters

arg = 2 - Card Diag parameters

2 Display PXM diagnostic parameters

arg = 1 - Online Diag parameters

arg = 2 - Offline Diag parameters

3 Set diagnostic trace level

arg = 0 - Silent

arg = 1 - Normal

arg = 2 - Verbose Low

arg = 3 - Verbose High

arg = 4 - Debug Low

arg = 5 - Debug High

4 Set offline diagnostics to verbose mode

arg = 0 - Silent

arg = 1 - Normal

arg = 2 - Verbose Low

arg = 3 - Verbose High

arg = 4 - Debug Low

arg = 5 - Debug High

5 Show date

6 Display diag memory map

7 Dump memory arg = memory address in the range 0x80000000-0x81000000


Related Commands

cnfdiag

Attributes

Log: yes

State: active, standby

Privilege: SERVICE_GP


Examples

Display the offline PXM diagnostic parameters.

PXM1E_SJ.8.PXM.a > diagdebug 2 2

PXM1E_COMMON:
cardMode=1 cardRole=1 cardAppId=10018 cardType=c20
myEpId=80011af myPhySlot=8 myLogSlot=7 myPhyShelf=1
subTaskId=1005f diagMode=0 verbose=1 errCntr=0
running=0 booting=0 abortTest=0 switchOver=0 ready=1 timerOn=0
onEnb=0 offEnb=0 cover=0 start=00:00 dow=7f

PXM1E_SJ.8.PXM.a > 

disablesscop

Disable SSCOP—PXM45

The disablesscop command lets you disable SSCOP on a port. The port must be administratively down (by the dnpnport command). Be sure a valid and useful reason exists for disabling SSCOP.

Syntax

disablesscop <portid> {yes | no}

Syntax Description

portid

The format of the PNNI physical port identifier can vary, as follows:

On a PXM45: slot:subslot.port:subport

On a PXM1E for UNI/NNI back card: slot:subslot.port:subport. On the UNI/NNI back card, the subslot is always 2, but the slot depends on the chassis, as follows:

In an MGX 8850 chassis, slot is always the logical slot 7.

In an MGX 8830 chassis, slot is always the logical slot 1.

On a PXM1E for a narrowband service module (NBSM): slot.port.

For more details, see the section, "PNNI Format," in "Introduction."

yes or
no

The choice for disabling or enabling SSCOP on the port:

yes means disable SSCOP.

no means enable SSCOP.

Default: no (enable SSCOP on the specified port)


Related Commands

cnfsscop, dspsscop, dspsscopstats

Attributes

Log: no

State: active

Privilege: GROUP1


Example

Disable SSCOP on port 11:2.8:28.

Geneva.7.PXM.a > disablesscop 11:2.8:28 yes

Geneva.7.PXM.a >

dncon

Down Connection—PXM1E

The dncon command administratively deactivates (or "downs") a connection so that you can modify or troubleshoot the network. This command applies to SPVCs only. If a connection is a point-to-multipoint (P2MP) connection, all parties on it are de-routed.

To activate the connection, use the upcon command.

Syntax

dncon <ifNum> <vpi> <vci>

Syntax Description

ifNum

The range for logical interface (or port) numbers is are as follows 1-31.

vpi

Virtual path identifier. On a UNI, the range is 0-255. On an NNI, the range is 0-4095.

vci

For a virtual connection (VCC) on a UNI, the range is 1-4095. On an NNI or VNNI, the VCI range is 1-65535. For MPLS, the recommended minimum VCI is 35.

For a virtual path connection (VPC), the VCI is always 0.


Related Commands

upcon

Attributes

Log: yes

State: active

Privilege: GROUP1


dnimagrp

Down IMA Group—PXM1E

This command administratively disables an IMA group.

The order of commands for downing and upping an IMA group is as follows:

1. dnimagrp

2. upimagrp

3. rstrtimagrp

Syntax

dnimagrp <group>

Syntax Description

group

The group identifier consists of a bay number as well as a group number in the format bay.group, as follows:

bay: always 2 on the PXM1E

group: 1-16


Related Commands

upimagrp

Attributes

Log: no

State: active

Privilege: ANYUSER


Example

Disable IMA group number 16.

MGX8850.7.PXM1E.a > dnimagrp 2.16

dnilmi

Down ILMI—PXM1E

The dnilmi command lets you de-activate (down) ILMI on a logical port so you can modify a configuration, troubleshoot, or run certain commands that require ILMI to be inoperative.

Syntax

dnilmi <ifNum> <partId>

Syntax Description

ifNum

The range for logical interface (or port) numbers is are as follows 1-31.

partId

The range for partition ID is 1-20.


Related Commands

dspilmi, dspilmis, upilmi

Attributes

Log: yes

State: active, standby

Privilege: SERVICE_GP


dnln

Down Line—PXM45, PXM1E

On a PXM1E, the dnln command de-activates a line on one of two different card types. The line can be on the PXM1E UNI/NNI back card or on a service resource module (SRME or SRM-3T3). A dnln command also runs on the AXSMs in a switch with a PXM45. See the other dnln description for details.


Note On the CLI of the PXM45, the dnln command appears but is not supported in the current release.


Syntax

dnln <X>.<line>

Syntax Description

X

X identifies the card. For SRMs, X differs in an MGX 8850 and MGX 8830 chassis:

X = 2 identifies the UNI/NNI back card on the PXM1E

X = 15 or 31 identifies an SRM in an MGX 8850 chassis (includes redundant cards in 16 or 32)

X = 7 identifies an SRM in an MGX 8830 chassis (includes redundant card in slot 14)

line

The range for line numbers depends on the card type and is from 1 to the highest numbered line on the back card, as follows:

PXM1E back card: 1-16

SRM-3T3: 1-3

SRME: 1


Related Commands

dspln, dsplns, cnfln, upln

Attributes

Log: yes

State: active

Privilege: GROUP1


Example

Down line 1 on the back card of the PXM1E.

MGX8850.7.PXM1E.a > dnln 2.1

dnparty

Down Party—PXM45, PXM1E

This command lets you administratively down a party on a point-to-multipoint (P2MP) connection. To up the party, use the upparty command. See the addparty description for details about parties on a P2MP.

Syntax

dnparty portid vpi vci endpointRef

Syntax Description

portid

The format of the PNNI physical port identifier can vary, as follows:

On a PXM45: slot:subslot.port:subport

On a PXM1E for UNI/NNI back card: slot:subslot.port:subport. On the UNI/NNI back card, the subslot is always 2, but the slot depends on the chassis, as follows:

In an MGX 8850 chassis, slot is always the logical slot 7.

In an MGX 8830 chassis, slot is always the logical slot 1.

On a PXM1E for a narrowband service module (NBSM): slot.port.

For more details, see the section, "PNNI Format," in "Introduction."

vpi

The local VPI of the connection is in one of the following ranges:

UNI: 0-255

NNI: 0-4095

vci

The local VCI of the connection has a range of 35-65535.

endpointRef

The endpoint reference has a range of 1-32767


Related Commands

addcon, delparty, rrtparty, upparty, addparty, dspparty, dspparties, dsppartiespercon, dspcon, dspcons, dsppnport, dsppnports, clrspvcnonpers

Attributes

Log: yes

State: active

Privilege: GROUP1


Example

dnpnport

Down PNNI Port—PXM45, PXM1E

The dnpnport command takes a UNI or NNI port out of service (administratively "downs" a port). For example, downing a port is necessary for certain provisioning activity or maintenance activity. Where appropriate, the applicable commands state that you must down a port by using dnpnport.


Note This command deletes all connections on a port—except for SPVCs whose endpoints are on the port.


Syntax

dnpnport <portid>

Syntax Description

portid

The format of the PNNI physical port identifier can vary, as follows:

On a PXM45: slot:subslot.port:subport

On a PXM1E for UNI/NNI back card: slot:subslot.port:subport. On the UNI/NNI back card, the subslot is always 2, but the slot depends on the chassis, as follows:

In an MGX 8850 chassis, slot is always the logical slot 7.

In an MGX 8830 chassis, slot is always the logical slot 1.

On a PXM1E for a narrowband service module (NBSM): slot.port.

For more details, see the section, "PNNI Format," in "Introduction."


Related Commands

addpnport, delpnport, uppnport, dsppnport

Attributes

Log: yes

State: active

Privilege: GROUP1


Examples

Remove port 11:2.8:22 from service.

Geneva.7.PXM.a > dnpnport 11:2.8:28

Geneva.7.PXM.a > 

dnport

Down Port—PXM1E

The dnport command disables (or downs) a logical port and thereby halts all traffic and triggers connection re-routing on the port. The usual purpose for using dnport is troubleshooting. The port keeps its configuration whether the port is a UNI or an NNI. The command for activating the port is upport.

For an NNI, the PXM de-routes the failed connections then re-routes them through other NNIs. After you activate an NNI port through upport, the re-routed connections do not return to the upped port.

On a UNI, the connections continue to exist, but remain in the failed state until you enable the port by using upport.

Syntax

dnport <ifNum>

Syntax Description

ifNum

The range for logical interface (or port) numbers is 1-31.

Use dspports or dspport as needed to determine the need to disable a port.


Related Commands

dspport, dspports, upport

Attributes

Log: yes

State: active

Privilege: GROUP1


Example

Disable port 1 on the current card.

MGX8850.7.PXM1E.a > dnport 1

downloadflash

Download Flash—PXM45, PXM1E

The downloadflash command does not execute at the runtime prompt. It operates in bootmode only.

A downloadflash session concludes the sequence of tasks for performing a PXM boot code load. Prior to executing this command, you must access the boot code and transfer the file to the PXM hard drive by using a "put" command). Arguments within the "put" command let you load boot code to any combination of standby or active PXMs. (See Example section for details.) Once firmware is installed in slot 7, the bootcode is mirrored to a new PXM in slot 8 if present. However, to ensure that the boot code is correct, use downloadflash as a manual way to download the boot code to the standby PXM.


Note Make sure only one version of backup boot code resides in the firmware directory: either delete or rename old versions to ensure that downloadflash uses the correct version.


Syntax

downloadflash

Related Commands

None

Attributes

Log: no

State: active, standby

Privilege: SUPER_GP


Example

Do a PXM45 boot code load. Start with a tftp to the boot code source. Conclude with the download to the standby and the active PXM45. Despite the ".fw" argument in the command string, this is NOT a firmware load. The first lines show an attempt to run downloadflash within the runtime image.

Unknown.7.PXM.a > downloadflash 
Error: flash_file supported only at backup boot 

> ftp <switch_dest_addr> 
> bin 
> put <pxm_bkup_version>.fw PINNACLE@PXM45.BT 
> quit
wilco.7.PXM.a > downloadflash

To place the boot code on the active PXM45 only, use the following "put" string:
>put pxm_bkup_version>.fw PINNACLE@PXM45_ACTIVE.BT

To place the boot code on the standby PXM45 only, use the following "put" string:
>put pxm_bkup_version>.fw PINNACLE@PXM45_STANDBY.BT