Release Notes for Cisco IOS Release 12.2SXF and Rebuilds
Hardware
Downloads: This chapterpdf (PDF - 828.0KB) The complete bookPDF (PDF - 8.72MB) | Feedback

Supported Hardware

Table Of Contents

Supported Hardware

Supervisor Engines

Supervisor Engine 720 (CAT6000-SUP720/MSFC3, 7600-SUP720/MSFC3)

Supervisor Engine 32 (CAT6000-SUP32/MSFC2A, 7600-SUP32/MSFC2A)

Supervisor Engine 2 (CAT6000-SUP2/MSFC2, 7600-SUP2/MSFC2)

Policy Feature Cards

Policy Feature Card Guidelines and Restrictions

Policy Feature Card 3BXL

Policy Feature Card 3B

Policy Feature Card 3A

Distributed and Centralized Forwarding Cards

Distributed Forwarding Card 3CXL

Distributed Forwarding Card 3C

Distributed Forwarding Card 3BXL

Distributed Forwarding Card 3B

Distributed Forwarding Card 3A

Distributed Forwarding Card (WS-F6K-DFC)

Centralized Forwarding Card (WS-F6700-CFC)

Switch Fabric Modules

Transceivers

X2 Modules

XENPAKs

Small Form-Factor Pluggable (SFP) Modules

Gigabit Interface Converters (GBICs)

10-Gigabit Ethernet Switching Modules

Gigabit Ethernet Switching Modules

Power over Ethernet Daughtercards

10/100/1000 Ethernet Switching Modules

Fast Ethernet Switching Modules

Ethernet/Fast Ethernet (10/100) Switching Modules

Ethernet Switching Modules

Optical Services Modules (OSMs)

OSM Guidelines and Restrictions

Gigabit Ethernet WAN

OC-48 Packet over SONET

OC-48 DPT/Packet over SONET

OC-12 Packet over SONET

OC-3 Packet over SONET

OC-12 Channelized

CT3/T1 Channelized/Unchannelized

OC-12 ATM

Shared Port Adapter (SPA) Interface Processors (SIPs)

Shared Port Adapters (SPAs)

Ethernet SPAs

POS SPAs

ATM SPAs

SFPs for OC3 and OC12 POS and ATM SPAs

Serial SPAs

Services SPA Carrier (SSC)

Services SPAs

FlexWAN and Enhanced FlexWAN Modules

FlexWAN and Enhanced FlexWAN Module Port Adapters

Service Modules

Application Control Engine (ACE) Module

Wireless Services Module (WiSM)

Application-Oriented Networking Module

WebVPN Services Module

Anomaly Guard Module

Traffic Anomaly Detector Module

Wireless LAN Service Module (WLSM)

Persistent Storage Device (PSD) Module

Multi-Processor WAN Application Module (MWAM)

Content Services Gateway (CSG) Module

Communication Media Module (CMM)

IPsec VPN Acceleration Services Module

Content Switching Module with SSL (CSM-S)

Content Switching Module (CSM)

Firewall Services Module

Intrusion Detection System Modules (IDSMs)

Network Analysis Modules (NAMs)

Secure Sockets Layer (SSL) Services Module

Fan Trays

High-Capacity Fan Trays

Standard-Capacity Fan Trays

Power Supplies

CISCO7606 Power Supplies

WS-C6504-E and CISCO7604 Power Supplies

WS-C6503, WS-C6503-E, and CISCO7603 Power Supplies

All Other Power Supplies

Chassis

13-Slot Chassis

9-Slot Chassis

6-Slot Chassis

4-Slot Chassis

3-Slot Chassis

Unsupported Hardware


Supported Hardware

These sections describe the hardware supported in Release 12.2SX:

Supervisor Engines

Policy Feature Cards

Distributed and Centralized Forwarding Cards

Switch Fabric Modules

Transceivers

10-Gigabit Ethernet Switching Modules

Gigabit Ethernet Switching Modules

Power over Ethernet Daughtercards

10/100/1000 Ethernet Switching Modules

Fast Ethernet Switching Modules

Ethernet/Fast Ethernet (10/100) Switching Modules

Ethernet Switching Modules

Optical Services Modules (OSMs)

Shared Port Adapter (SPA) Interface Processors (SIPs)

Shared Port Adapters (SPAs)

Services SPA Carrier (SSC)

Services SPAs

FlexWAN and Enhanced FlexWAN Modules

FlexWAN and Enhanced FlexWAN Module Port Adapters

Service Modules

Fan Trays

Power Supplies

Chassis


NoteUse the values in the "Power Required" column to determine the exact power requirements for your configuration to ensure that you are within the power budget.

Daughtercard power is shown separately.

Enter the show power command to display current system power usage.

Flash Memory Device Summary

bootflash: on the RP of all supervisor engines.

sup-bootdisk: on these supervisor engines:

Supervisor Engine 720 with a CompactFlash adapter and CompactFlash card.

Supervisor Engine 32.

sup-bootflash: on these supervisor engines:

Supervisor Engine 720 without a CompactFlash adapter and CompactFlash card.

Supervisor Engine 2.

disk0: on these supervisor engines:

Supervisor Engine 720.

Supervisor Engine 32.

Supervisor Engine 2 with a PCMCIA Advanced Technology Attachment (ATA) FlashDisk device.

disk1: on a Supervisor Engine 720.

slot0: on a Supervisor Engine 2 without a PCMCIA Advanced Technology Attachment (ATA) FlashDisk device.


Supervisor Engines

Supervisor Engine 720 (CAT6000-SUP720/MSFC3, 7600-SUP720/MSFC3)

Supervisor Engine 32 (CAT6000-SUP32/MSFC2A, 7600-SUP32/MSFC2A)

Supervisor Engine 2 (CAT6000-SUP2/MSFC2, 7600-SUP2/MSFC2)

Supervisor Engine 720 (CAT6000-SUP720/MSFC3, 7600-SUP720/MSFC3)

Supervisor Engine 720 Common Features

Supervisor Engine 720 with PFC3BXL

Supervisor Engine 720 with PFC3B

Supervisor Engine 720 with PFC3A

Supervisor Engine 720 Common Features

Integrated 720-Gbps Switch Fabric

64-MB bootflash device or CompactFlash adapter with 512 MB CompactFlash card (WS-CF-UPG=):

64-MB bootflash device (sup-bootflash:) supported in all releases

WS-CF-UPG= (sup-bootdisk:) supported in:

—Release 12.2(18)SXE5 and later releases

—Release 12.2(18)SXF and later releases

See this publication:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_17277.html

2 CompactFlash Type II slots (disk0: and disk1:)


Note Some Supervisor Engine 720 Release 12.2SX images are larger than the bootflash device and must be stored on a CompactFlash card (sup-bootdisk: or disk0: or disk1:).


Two Ethernet uplink ports:

1-MB packet buffer per port

Port 1—Gigabit Ethernet SFP

Port 2—Configurable as Gigabit Ethernet SFP or 10/100/1000 Mbps RJ-45

QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t

Port grouping:

Number of ports: 2

Number of port groups: 1

Port ranges per port group: 1-2

Supervisor Engine 720 requires a high-capacity fan tray (see the "Fan Trays" section)

Supervisor Engine 720 requires a 2500W or higher power supply (see the "Power Supplies" section)

Supervisor Engine 720 with PFC3BXL

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-SUP720-3BXL

7.82 A@42 V

Supervisor Engine 720 with PFC3BXL:

1-GB DRAM

Policy Feature Card 3BXL (PFC3BXL; see the "Policy Feature Cards" section)

Multilayer Switch Feature Card 3 (MSFC3):

1-GB DRAM

64-MB bootflash

12.2(17b)SXA

 

Note

There are no memory upgrade options for WS-SUP720-3BXL.

If you install WS-SUP720-3BXL=, upgrade the memory on any DFC3-equipped switching modules. See this document for DFC3 memory upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12409.html


Supervisor Engine 720 with PFC3B

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-SUP720-3B

6.72 A@42 V

Supervisor Engine 720 with PFC3B:

512-MB DRAM

Policy Feature Card 3B (PFC3B; see the "Policy Feature Cards" section)

Multilayer Switch Feature Card 3 (MSFC3):

512-MB DRAM

64-MB bootflash

12.2(17d)SXB1

 

Note

See this document for DFC3 memory upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12409.html

Use WS-F6K-PFC3BXL= to upgrade a WS-SUP720-3B with a PFC3BXL. WS-F6K-PFC3BXL= includes 1 GB memory upgrades for the Supervisor Engine 720 and the MSFC3.

If you install WS-F6K-PFC3BXL=, upgrade the memory on any DFC3-equipped switching modules.

See this publication for more information about WS-F6K-PFC3BXL=:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_16220.html

You can upgrade the WS-SUP720-3B memory to 1-GB DRAM on the Supervisor Engine 720 and 1-GB DRAM on the MSFC3.

If you upgrade the memory, upgrade the Supervisor Engine 720, the MSFC3, and any DFC3-equipped switching modules.

See this document for Supervisor Engine 720 and MSFC3 memory upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/OL_20611.html


Supervisor Engine 720 with PFC3A

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-SUP720

7.50 A@42 V

Supervisor Engine 720 with PFC3A:

512-MB DRAM

Policy Feature Card 3A (PFC3A; see the "Policy Feature Cards" section)

Multilayer Switch Feature Card 3 (MSFC3):

512-MB DRAM

64-MB bootflash

12.2(14)SX

   

Note

See this document for DFC3 memory upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12409.html

Use WS-F6K-PFC3BXL= to upgrade a WS-SUP720 with a PFC3BXL. WS-F6K-PFC3BXL= includes 1 GB memory upgrades for the Supervisor Engine 720 and the MSFC3.

If you install WS-F6K-PFC3BXL=, upgrade the memory on any DFC3-equipped switching modules.

See this publication for more information about WS-F6K-PFC3BXL=:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_16220.html

Except with WS-F6K-PFC3BXL=, do not upgrade the memory on WS-SUP720 or on the MSFC3 on WS-SUP720.


Supervisor Engine 32 (CAT6000-SUP32/MSFC2A, 7600-SUP32/MSFC2A)

These sections describe the Supervisor Engine 32:

Supervisor Engine 32 Restrictions

Supervisor Engine 32 Features

Supervisor Engine 32 Restrictions

Supervisor Engine 32 requires a high-capacity fan tray (see the "Fan Trays" section).

In some chassis, Supervisor Engine 32 requires a high-capacity power supply (see the "Power Supplies" section).

Supervisor Engine 32 does not support this hardware:

WS-F6K-PFC3A Policy Feature Card 3A (PFC3A)

WS-F6K-PFC3BXL Policy Feature Card 3BXL (PFC3BXL)

DFCs (installed DFCs do not power up with a Supervisor Engine 32)

Switch Fabric Modules

These switching modules:
—WS-X6704-10GE 4-port 10-Gigabit Ethernet XENPAK
—WS-X6748-SFP 48-port Gigabit Ethernet SFP
—WS-X6724-SFP 24-port Gigabit Ethernet SFP
—WS-X6816-GBIC 16-port Gigabit Ethernet GBIC
—WS-X6748-GE-TX 48-port 10/100/1000 RJ-45

7600-SIP-600 SPA Interface Processor-600

Optical Services Modules (OSMs)

WS-X6182-2PA FlexWAN Module (the WS-X6582-2PA Enhanced FlexWAN Module is supported)

CISCO7603 3-slot chassis

These service modules:
—WS-SVC-WISM-1-K9 Wireless Services Module (WiSM)
—WS-SVC-AON-1-K9 Application-Oriented Networking (AON) Module
—WS-SVC-AGM-1-K9 Anomaly Guard Module
—WS-SVC-ADM-1-K9 Traffic Anomaly Detector Module
—WS-SVC-CSG-1 Content Services Gateway (CSG)
—WS-X6066-SLB-APC Content Switching Module (CSM)
—WS-X6066-SLB-S-K9 Content Switching Module with SSL (CSM-S)
—WS-SVC-PSD-1 Persistent Storage Device (PSD) Module
WS-SVC-WLAN-1-K9 Wireless LAN service module
—WS-SVC-IPSEC-1 IPsec VPN acceleration services module

Releases earlier than Release 12.2(18)SXF do not support Cisco IOS SLB with Supervisor Engine 32.

Supervisor Engine 32 cannot support these software features and commands:

Egress multicast replication

Multicast replication mode detection

All fabric configuration commands

Supervisor Engine 32 Features

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-SUP32-10GE-3B

2.39 A@42 V

Supervisor Engine 32:

One 10/100/1000 Mbps RJ-45 port

WS-SUP32-10GE—two 10-Gigabit Ethernet ports (requires XENPAKs)

WS-SUP32-GE—eight Gigabit Ethernet SFP ports (requires Gigabit Ethernet SFPs)

QoS port architecture (Rx/Tx): 2q8t/1p3q8t

256-MB DRAM with the "IP BASE SSH LAN ONLY" image (does not apply to the "IP BASE SSH LAN ONLY (MODULAR)" image)

512-MB DRAM with all other images

256-MB bootflash

Policy Feature Card 3B (PFC3B; see the "Policy Feature Cards" section)

Multilayer Switch Feature Card 2A (MSFC2A):

256-MB DRAM with the "IP BASE SSH LAN ONLY" image (does not apply to the "IP BASE SSH LAN ONLY (MODULAR)" image)

512-MB DRAM with all other images

64-MB bootflash

12.2(18)SXF

WS-SUP32-GE-3B

1.89 A@42 V

 

Note See this publication for Supervisor Engine 32 hardware information:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Module_Installation/Sup_Eng_Guide/supe_gd.html


Supervisor Engine 2 (CAT6000-SUP2/MSFC2, 7600-SUP2/MSFC2)

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-X6K-S2U-MSFC2
WS-X6K-S2-MSFC2

3.46 A@42 V

Supervisor Engine 2 with Policy Feature Card 2 (PFC2):

ROMMON version 7.1(1) or later

32-MB bootflash device

256-MB DRAM (minimum)

dual-port 1000BASE-X GBIC uplinks

QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t

Number of ports: 2
Number of port groups: 1
Port ranges per port group: 1-2

Multilayer Switch Feature Card 2 (MSFC2) with 256-MB DRAM (minimum)

12.2(17d)SXB

 

Note

Some Supervisor Engine 2 Release 12.2SX images are larger than the bootflash device. Supervisor Engine 2 ROMMON version 7.1(1) or later supports the MEM-C6K-ATA-1-64M= (64 MB) PCMCIA ATA FlashDisk device. See this publication:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_13488.html

To use WS-X6K-S2-MSFC2 with 12.2SX releases, upgrade the memory.

MSFC2 DRAM—See this publication:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_6953.html

Supervisor Engine 2 DRAM—See this publication:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12693.html

Supervisor Engine 2 Bootflash—See this publication:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12667.html

Supervisor Engine 2 supports all GBICs supported by Release 12.2(17d)SXB and later releases.


Policy Feature Cards

Policy Feature Card Guidelines and Restrictions

Policy Feature Card 3BXL

Policy Feature Card 3B

Policy Feature Card 3A

Policy Feature Card Guidelines and Restrictions

A Supervisor Engine 2 always has a PFC2; there are no PFC options for Supervisor Engine 2.

The PFC2 supports a theoretical maximum of 128 K MAC addresses (32 K MAC addresses recommended maximum).

The PFC3 supports a theoretical maximum of 64 K MAC addresses (32 K MAC addresses recommended maximum).

The PFC3 partitions the hardware FIB table to route IPv4 unicast, IPv4 multicast, MPLS, and IPv6 unicast and multicast traffic in hardware. Traffic for routes that do not have entries in the hardware FIB table are routed by the MSFC in software.

The defaults for XL mode are:

IPv4 unicast and MPLS—512,000 routes

IPv4 multicast and IPv6 unicast and multicast—256,000 routes

The defaults for Non-XL mode are:

IPv4 unicast and MPLS—192,000 routes

IPv4 multicast and IPv6 unicast and multicast—32,000 routes


Note The size of the global internet routing table plus any local routes might exceed the non-XL mode default partition sizes.


These are the theoretical maximum numbers of routes for the supported protocols (the maximums are not supported simultaneously):

XL mode:

· IPv4 and MPLS—Up to 1,007,000 routes

· IPv4 multicast and IPv6 unicast and multicast—Up to 503,000 routes

Non-XL mode:

· IPv4 and MPLS—Up to 239,000 routes

· IPv4 multicast and IPv6 unicast and multicast—Up to 119,000 routes

Enter the mls cef maximum-routes command to repartition the hardware FIB table. IPv4 unicast and MPLS require one hardware FIB table entry per route. IPv4 multicast and IPv6 unicast and multicast require two hardware FIB table entries per route. Changing the partition for one protocol makes corresponding changes in the partitions of the other protocols. You must enter the reload command to put configuration changes made with the mls cef maximum-routes command into effect.


Note With a non-XL-mode system, if your requirements cannot be met by repartitioning the hardware FIB table, upgrade components as necessary to operate in XL mode.


You cannot use one type of PFC3 (PFC3BXL, PFC3B, or PFC3A) on one supervisor engine and a different type on the other supervisor engine for redundancy. You must use identical policy feature cards for redundancy.

With Release 12.2(17d)SXB and later releases, enter the show platform hardware pfc mode command to display the PFC3 mode.

With Release 12.2(17b)SXA and Release 12.2(17b)SXA2, enter the show platform earl-mode command to display the PFC3 mode.

PFC3A—These restrictions apply to a configuration with a PFC3A and these DFCs:

PFC3A and DFC3A—No restrictions (PFC3A mode).

PFC3A and DFC3B—The PFC3A restricts DFC3B functionality: the DFC3B functions as a DFC3A (PFC3A mode).

PFC3A and DFC3BXL—The PFC3A restricts DFC3BXL functionality: the DFC3BXL functions as a DFC3A (PFC3A mode).

PFC3A and DFC3C—The PFC3A restricts DFC3C functionality: the DFC3C functions as a DFC3A (PFC3A mode).

PFC3A and DFC3CXL—The PFC3A restricts DFC3CXL functionality: the DFC3CXL functions as a DFC3A (PFC3A mode).

PFC3B—These restrictions apply to a configuration with a PFC3B and these DFCs:

PFC3B and DFC3A—PFC3B functionality is restricted by the DFC3A: after a reload with a DFC3A-equipped module installed, the PFC3B functions as a PFC3A (PFC3A mode).

PFC3B and DFC3B—No restrictions (PFC3B mode).

PFC3B and DFC3BXL—The PFC3B restricts DFC3BXL functionality: after a reload with a DFC3BXL-equipped module installed, the DFC3BXL functions as a DFC3B (PFC3B mode).

PFC3B and DFC3C—The PFC3B restricts DFC3C functionality: the DFC3C functions as a DFC3B (PFC3B mode).

PFC3B and DFC3CXL—The PFC3B restricts DFC3CXL functionality: the DFC3CXL functions as a DFC3B (PFC3B mode).

PFC3BXL—These restrictions apply to a configuration with a PFC3BXL and these DFCs:

PFC3BXL and DFC3A—PFC3BXL functionality is restricted by the DFC3A: after a reload with a DFC3A-equipped module installed, the PFC3BXL functions as a PFC3A (PFC3A mode).

PFC3BXL and DFC3B—PFC3BXL functionality is restricted by the DFC3B: after a reload with a DFC3B-equipped module installed, the PFC3BXL functions as a PFC3B (PFC3B mode).

PFC3BXL and DFC3BXL—No restrictions (PFC3BXL mode).

PFC3BXL and DFC3C—Each restricts the functionality of the other: the PFC3BXL functions as a PFC3B and the DFC3C functions as a DFC3B (PFC3B mode).

PFC3BXL and DFC3CXL—The PFC3BXL restricts DFC3CXL functionality: the DFC3CXL functions as a DFC3BXL (PFC3BXL mode).

Summary of the PFC modes:

PFC3A mode—Operating mode with a PFC3A or any DFC3As

PFC3B mode—Operating mode with PFC3B and any DFC3Bs or DFC3BXLs

PFC3BXL mode—Operating mode with PFC3BXL and any DFC3BXLs

The features that require the PFC3BXL or PFC3B are not supported in PFC3A mode.

With a PFC3BXL or PFC3B and no DFC3A-equipped switching modules installed at bootup, any DFC3A-equipped switching module installed after bootup remain powered down.

To use DFC3A-equipped switching modules with a PFC3BXL or PFC3B, the DFC3A-equipped switching modules must be installed at bootup.

To use DFC3B-equipped switching modules with a PFC3BXL, the DFC3B-equipped switching modules must be installed at bootup.

Policy Feature Card 3BXL

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-F6K-PFC3BXL

2.57 A@42 V

Policy Feature Card 3BXL (PFC3BXL)

 

Supported only with Supervisor Engine 720

12.2(17b)SXA

Note

There are no memory upgrade options for WS-F6K-PFC3BXL.

Use WS-F6K-PFC3BXL= to upgrade a WS-SUP720 or WS-SUP720-3B with a PFC3BXL. WS-F6K-PFC3BXL= includes 1 GB memory upgrades for the Supervisor Engine 720 and the MSFC3. See this publication for more information:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_16220.html


Policy Feature Card 3B

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-F6K-PFC3B

2.25 A@42 V

Policy Feature Card 3B (PFC3B)

With Supervisor Engine 720

12.2(17d)SXB1

With Supervisor Engine 32

12.2(18)SXF

Note

There are no memory upgrade options for WS-F6K-PFC3B.

Use WS-F6K-PFC3BXL= to upgrade a WS-SUP720-3B with a PFC3BXL. WS-F6K-PFC3BXL= includes 1 GB memory upgrades for the Supervisor Engine 720 and the MSFC3. See this publication for more information:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_16220.html


Policy Feature Card 3A

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-F6K-PFC3A

2.25 A@42 V

Policy Feature Card 3A (PFC3A)

 

Supported only with Supervisor Engine 720

12.2(14)SX

Note

There are no memory upgrade options for WS-F6K-PFC3A.

WS-F6K-PFC3A is available only on WS-SUP720. It is not orderable.


Distributed and Centralized Forwarding Cards

Distributed Forwarding Card 3CXL

Distributed Forwarding Card 3C

Distributed Forwarding Card 3BXL

Distributed Forwarding Card 3B

Distributed Forwarding Card 3A

Distributed Forwarding Card (WS-F6K-DFC)

Centralized Forwarding Card (WS-F6700-CFC)


Note See the "Policy Feature Cards" section for Policy Feature Cards (PFC) and Distributed Forwarding Card (DFC) restrictions.


Distributed Forwarding Card 3CXL

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-F6700-DFC3CXL

2.35 A@42 V

Distributed Forwarding Card 3CXL (DFC3CXL) for use on CEF720 modules

 

Supported only with Supervisor Engine 720 and WS-X6708-10GE

12.2(18)SXF5


Distributed Forwarding Card 3C

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-F6700-DFC3C

1.65 A@42 V

Distributed Forwarding Card 3C (DFC3C) for use on CEF720 modules

 

Supported only with Supervisor Engine 720 and WS-X6708-10GE

12.2(18)SXF5


Distributed Forwarding Card 3BXL

WS-F6700-DFC3BXL

WS-F6K-DFC3BXL

WS-F6700-DFC3BXL

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-F6700-DFC3BXL

3.30 A@42 V

Distributed Forwarding Card 3BXL (DFC3BXL) for use on CEF720 modules

 

Supported only with Supervisor Engine 720

12.2(17d)SXB6

Note

WS-F6700-DFC3BXL uses memory that is installed on the switching module.

See this publication for information about WS-F6700-DFC3BXL upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_15893.html


WS-F6K-DFC3BXL

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-F6K-DFC3BXL

1.47 A@42 V

Distributed Forwarding Card 3BXL (DFC3BXL) for use on dCEF256 and CEF256 modules

 

Supported only with Supervisor Engine 720

12.2(18)SXD3

Note

See this publication for information about WS-F6K-DFC3BXL memory upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12409.html

Supervisor Engine 720 supports a WS-F6K-DFC3BXL on these WS-X6516-GBIC switching module hardware revisions:

Lower than 5.0

5.5 and higher

Supervisor Engine 720 does not support a DFC3 on WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4. With a Supervisor Engine 720 and with a DFC3 installed, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 do not power up.

With a Supervisor Engine 720 but without a DFC3, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 operate in bus mode.

See external field notice 24494 for more information about Supervisor Engine 720 and a DFC3 on WS-X6516-GBIC switching modules:

http://www.cisco.com/en/US/ts/fn/200/fn24494.html


Distributed Forwarding Card 3B

WS-F6700-DFC3B

WS-F6K-DFC3B

WS-F6700-DFC3B

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-F6700-DFC3B

2.70 A@42 V

Distributed Forwarding Card 3B (DFC3B) for use on CEF720 modules

 

Supported only with Supervisor Engine 720

12.2(17d)SXB6

Note

WS-F6700-DFC3B uses memory that is installed on the switching module.

See this publication for information about WS-F6700-DFC3B upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_15893.html


WS-F6K-DFC3B

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-F6K-DFC3B

1.67 A@42 V

Distributed Forwarding Card 3B (DFC3B) for use on dCEF256 and CEF256 modules

 

Supported only with Supervisor Engine 720

12.2(18)SXD3

Note

See this publication for information about WS-F6K-DFC3B memory upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12409.html

Supervisor Engine 720 supports a WS-F6K-DFC3B on these WS-X6516-GBIC switching module hardware revisions:

Lower than 5.0

5.5 and higher

Supervisor Engine 720 does not support a DFC3 on WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4. With a Supervisor Engine 720 and with a DFC3 installed, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 do not power up.

With a Supervisor Engine 720 but without a DFC3, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 operate in bus mode.

See external field notice 24494 for more information about Supervisor Engine 720 and a DFC3 on WS-X6516-GBIC switching modules:

http://www.cisco.com/en/US/ts/fn/200/fn24494.html


Distributed Forwarding Card 3A

WS-F6700-DFC3A

WS-F6K-DFC3A

WS-F6700-DFC3A

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-F6700-DFC3A

3.00 A@42 V

Distributed Forwarding Card 3A (DFC3A) for use on CEF720 modules

 

Supported only with Supervisor Engine 720

12.2(17a)SX

Note

WS-F6700-DFC3A uses memory that is installed on the switching module.

See this publication for information about WS-F6700-DFC3A memory upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12409.html


WS-F6K-DFC3A

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-F6K-DFC3A

2.57 A@42 V

Distributed Forwarding Card 3A (DFC3A) for use on dCEF256 and CEF256 modules

 

Supported only with Supervisor Engine 720

12.2(14)SX

Note

See this publication for information about WS-F6K-DFC3A memory upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12409.html

Supervisor Engine 720 supports a WS-F6K-DFC3A on these WS-X6516-GBIC switching module hardware revisions:

Lower than 5.0

5.5 and higher

Supervisor Engine 720 does not support a DFC3 on WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4. With a Supervisor Engine 720 and with a DFC3 installed, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 do not power up.

With a Supervisor Engine 720 but without a DFC3, WS-X6516-GBIC switching module hardware revisions 5.0 through 5.4 operate in bus mode.

See external field notice 24494 for more information about Supervisor Engine 720 and a DFC3 on WS-X6516-GBIC switching modules:

http://www.cisco.com/en/US/ts/fn/200/fn24494.html


Distributed Forwarding Card (WS-F6K-DFC)

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-F6K-DFC

2.10 A@42 V

Distributed Forwarding Card (DFC) for use on dCEF256 and CEF256 modules

 

Supported only with Supervisor Engine 2

Note Not supported in Release 12.2(18)SXE and Rebuilds

12.2(17d)SXB

Note

Release 12.2(18)SXE does not support Supervisor Engine 2.

WS-F6K-DFC requires a Switch Fabric Module.

See this publication for information about WS-F6K-DFC memory upgrades:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_12409.html


Centralized Forwarding Card (WS-F6700-CFC)

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-F6700-CFC

0.75 A@42 V

Centralized Forwarding Card (CFC) for use on CEF720 modules

 

Supported only with Supervisor Engine 720

12.2(17a)SX

Note There are no memory upgrade options for WS-F6700-CFC.


Switch Fabric Modules


NoteSwitch fabric modules are supported only with Supervisor Engine 2.

Except in 13-slot chassis, WS-X6500-SFM2 and WS-C6500-SFM can be used together to provide redundancy.

3-slot chassis do not support WS-X6500-SFM2 or WS-C6500-SFM.


Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-X6500-SFM2

3.09 A@42 V

Switch Fabric Module, version 2, to support dCEF256 modules

 

Supported only with Supervisor Engine 2

12.2(17d)SXB

Note WS-C6500-SFM2 supports all chassis except 3-slot chassis.

WS-C6500-SFM

2.79 A@42 V

Switch Fabric Module to support dCEF256 modules

 

Supported only with Supervisor Engine 2

12.2(17d)SXB

Note WS-C6500-SFM does not support 13-slot chassis or 3-slot chassis.


Transceivers

X2 Modules

XENPAKs

Small Form-Factor Pluggable (SFP) Modules

Gigabit Interface Converters (GBICs)

X2 Modules


Note WS-X6708-10GE does not support X2 modules shipped before the release of the WS-X6708-10GE switching module. The unsupported X2 modules are labeled with a number that ends with -01.


Product ID
(append "=" for spares)
Product Description
Minimum Software Version
X2-10GB-LRM

10GBASE-LRM for FDDI-grade multimode fiber (MMF)

Note Not supported by the show idprom command. (CSCsj35671)

12.2(18)SXF8

X2-10GB-CX4

10GBASE for CX4 (copper) cable

12.2(18)SXF5

X2-10GB-ER

10GBASE-ER Serial 1550-nm extended-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF)

12.2(18)SXF5

X2-10GB-LR

10GBASE-LR Serial 1310-nm long-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF)

12.2(18)SXF5

X2-10GB-LX4

10GBASE-LX4 Serial 1310-nm multimode (MMF)

12.2(18)SXF5

X2-10GB-SR

10GBASE-SR Serial 850-nm short-reach multimode (MMF)

12.2(18)SXF5


XENPAKs

Product ID
(append "=" for spares)
Product Description
Minimum Software Version
XENPAK-10GB-LRM

10GBASE-LRM XENPAK Module for MMF

Note Not supported by the show idprom command. (CSCsl21260)

12.2(18)SXF11

XENPAK-10GB-ZR

10GBASE for any SMF type

12.2(18)SXF

XENPAK-10GB-LW

10GBASE-LW XENPAK Module with WAN PHY for SMF

12.2(18)SXE

Note XENPAK-10GB-LW operates at an interface speed compatible with SONET/SDH OC-192/STM-64 and supports transmission at a data rate of 9.6Gbps.

DWDM-XENPAK

10GBASE dense wavelength-division multiplexing (DWDM) 100-GHz ITU grid

12.2(18)SXE

WDM-XENPAK-REC

10GBASE receive-only wavelength division multiplexing (WDM)

12.2(18)SXE

XENPAK-10GB-CX4

10GBASE for CX4 (copper) cable

12.2(17d)SXB1

XENPAK-10GB-SR

10GBASE-SR Serial 850-nm short-reach multimode (MMF)

12.2(17a)SX1

XENPAK-10GB-LX4

10GBASE-LX4 Serial 1310-nm multimode (MMF)

12.2(17a)SX1

XENPAK-10GB-ER+

10GBASE-ER Serial 1550-nm extended-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF)

12.2(17a)SX

XENPAK-10GB-ER

10GBASE-ER Serial 1550-nm extended-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF)

12.2(17a)SX

Note Release 12.2(17d)SXB1 and later releases do not support XENPAK-10GB-ER units with Part No. 800-24557-01, as described in this external field notice (CSCee47030):

http://www.cisco.com/en/US/ts/fn/200/fn29736.html

XENPAK-10GB-LR

10GBASE-LR Serial 1310-nm long-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF)

12.2(17a)SX

XENPAK-10GB-LR+

10GBASE-LR Serial 1310-nm long-reach, single-mode fiber (SMF), dispersion-shifted fiber (DSF)

12.2(17a)SX


Small Form-Factor Pluggable (SFP) Modules

These sections describe SFPs:

Gigabit Ethernet SFPs

Fast Ethernet SFPs

Gigabit Ethernet SFPs


Note See the "Unsupported Hardware" section for information about unsupported DWDM-SFPs.


Product ID
(append "=" for spares)
Product Description
Minimum Software Version
DWDM-SFP-6061

1000BASE-DWDM 1560.61 nm SFP (100-GHz ITU grid) SFP module

12.2(18)SXF8

DWDM-SFP-5979

1000BASE-DWDM 1559.79 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-5898

1000BASE-DWDM 1558.98 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-5655

1000BASE-DWDM 1556.55 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-5575

1000BASE-DWDM 1555.75 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-5494

1000BASE-DWDM 1554.94 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-5413

1000BASE-DWDM 1554.13 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-5252

1000BASE-DWDM 1552.52 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-5172

1000BASE-DWDM 1551.72 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-5092

1000BASE-DWDM 1550.92 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-5012

1000BASE-DWDM 1550.12 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-4851

1000BASE-DWDM 1548.51 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-4772

1000BASE-DWDM 1547.72 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-4612

1000BASE-DWDM 1546.12 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-4453

1000BASE-DWDM 1544.53 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-4373

1000BASE-DWDM 1543.73 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-4294

1000BASE-DWDM 1542.94 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-4214

1000BASE-DWDM 1542.14 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-4056

1000BASE-DWDM 1540.56 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-3977

1000BASE-DWDM 1539.77 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-3898

1000BASE-DWDM 1538.98 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-3819

1000BASE-DWDM 1538.19 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-3661

1000BASE-DWDM 1536.61 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-3582

1000BASE-DWDM 1535.82 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-3504

1000BASE-DWDM 1535.04 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-3425

1000BASE-DWDM 1534.25 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-3268

1000BASE-DWDM 1532.68 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-3190

1000BASE-DWDM 1531.90 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-3112

1000BASE-DWDM 1531.12 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-3033

1000BASE-DWDM 1530.33 nm SFP (100-GHz ITU grid) SFP module

GLC-BX-D

1000BASE-BX10 SFP module for single-strand SMF, 1490-nm TX/1310-nm RX wavelength

12.2(18)SXE

GLC-BX-U

1000BASE-BX10 SFP module for single-strand SMF, 1310-nm TX/1490-nm RX wavelength

12.2(18)SXE

GLC-ZX-SM

1000BASE-ZX SFP module

12.2(17d)SXB1

CWDM-SFP

1000BASE coarse wavelength-division multiplexing (CWDM) SFP module

12.2(17a)SX

GLC-T

1000BASE-T 10/100/1000 SFP module

Note Supported only at 1000 Mbps in supervisor engines.

12.2(17a)SX

GLC-LH-SMD
GLC-LH-SM

1000BASE-LX/LH SFP

12.2(17a)SX

GLC-SX-MMD
GLC-SX-MM

1000BASE-SX SFP

12.2(14)SX


Fast Ethernet SFPs


Note Only WS-X6148-FE-SFP supports these Fast Ethernet SFPs.


Product ID
(append "=" for spares)
Product Description
Minimum Software Version
GLC-FE-100BX-U

100BASE-BX10-U SFP

12.2(18)SXF2

GLC-FE-100BX-D

100BASE-BX10-D SFP

12.2(18)SXF2

GLC-FE-100EX

100BASEEX SFP

12.2(18)SXF

GLC-FE-100ZX

100BASEZX SFP

12.2(18)SXF

GLC-FE-100FX

100BASEFX SFP

12.2(18)SXF

GLC-FE-100LX

100BASELX SFP

12.2(18)SXF


Gigabit Interface Converters (GBICs)


Note The support listed in this section applies to all modules that use GBICs, including OSM LAN ports and OSM Gigabit Ethernet WAN ports, except as noted.


Product ID
(append "=" for spares)
Product Description
Minimum Software Version
WDM-GBIC-REC

Receive-only wavelength division multiplexing (WDM) GBIC

12.2(18)SXE

DWDM-GBIC

Dense wavelength division multiplexing (DWDM) GBIC

12.2(17a)SX

CWDM-GBIC-1470

Cisco 1000BASE-CWDM GBIC, 1470 nm (Gray)

12.2(17a)SX

CWDM-GBIC-1490

Cisco 1000BASE-CWDM GBIC, 1490 nm (Violet)

CWDM-GBIC-1510

Cisco 1000BASE-CWDM GBIC, 1510 nm (Blue)

CWDM-GBIC-1530

Cisco 1000BASE-CWDM GBIC, 1530 nm (Green)

CWDM-GBIC-1550

Cisco 1000BASE-CWDM GBIC, 1550 nm (Yellow)

CWDM-GBIC-1570

Cisco 1000BASE-CWDM GBIC, 1570 nm (Orange)

CWDM-GBIC-1590

Cisco 1000BASE-CWDM GBIC, 1590 nm (Red)

CWDM-GBIC-1610

Cisco 1000BASE-CWDM GBIC, 1610 nm (Brown)

WS-G5483

1000BASET GBIC

Note 1000BASET GBIC transceivers are not supported on OSM LAN ports and OSM Gigabit Ethernet WAN ports.

12.2(14)SX

WS-G5484

Short wavelength, 1000BASE-SX

12.2(14)SX

WS-G5486

Long wavelength/long haul, 1000BASE-LX/LH

12.2(14)SX

WS-G5487

Extended distance, 1000BASE-ZX

12.2(14)SX


10-Gigabit Ethernet Switching Modules

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-X6708-10G-3C
(WS-X6708-10GE  with
WS-F6700-DFC3C )

10.58A @42 V

8-port 10-Gigabit Ethernet X2module

dCEF720

Supports egress multicast replication

QoS port architecture (Rx/Tx): 8q4t/1p7q4t

Dual switch-fabric connections
Fabric Channel #1: Ports 2, 3, 6, 8
Fabric Channel #2: Ports 1, 4, 5, 7

Number of ports: 8
Number of port groups: 8
Port ranges per port group: 1 port in each group

WS-X6708-10G-3CXL
(WS-X6708-10GE  with
WS-F6700-DFC3CXL)

11.28A @ 42V

 

Supported only with Supervisor Engine 720

12.2(18)SXF5

Note

To use Cisco IOS Software Modularity images with 6700 series switching modules, ensure that the 6700 series switching modules have switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html

WS-X6708-10G-3C and WS-X6708-10G-3CXL are the orderable product IDs.

The front panel is labeled WS-X6708-10GE.

Cisco IOS software commands display WS-X6708-10GE with either WS-F6700-DFC3C or WS-F6700-DFC3CXL.

To configure WS-X6708-10GE port oversubscription, refer to the hw-module oversubscription command in the command reference at this URL:

http://www.cisco.com/en/US/docs/ios-xml/ios/interface/command/ir-f1.html#GUID-B5F8BEA0-B5DD-47BE-82F5-183765DF0F64

In these chassis, operation of a WS-X6708-10GE switching module without over-temperature alarms is supported only with operating temperatures up to 40° C:

WS-C6513

CISCO7613

WS-C6509

WS-C6509-NEB

OSR-7609

WS-C6506

CISCO7606

Full NEBS-compliance requires support for operating temperatures up to 55° C, which is available in all other chassis that support WS-X6708-10GE.


Note All E-Series chassis provide NEBS compliance.


Support in the WS-C6509-NEB-A chassis requires two FAN-MOD-09 modules.

WS-X6708-10GE ports do not support VACL capture. (CSCsb59015)

WS-X6708-10GE is not supported in the WS-C6503 and CISCO7603 chassis.

In a 13-slot chassis, WS-X6708-10GE is supported only in slots 9 through 13 and does not power up in other slots.

On WS-X6708-10GE ports, STP BPDUs are not exempt from Traffic Storm Control multicast suppression. Do not configure multicast suppression on STP-protected WS-X6708-10GE ports that interconnect network devices. (CSCsg86315)

WS-X6704-10GE

6.28 A@42 V

4-port 10-Gigabit Ethernet XENPAK

CEF720 with WS-F6700-CFC (adds 0.75 A@42 V)

dCEF720 with WS-F6700-DFC3BXL (adds 3.30 A@42 V)

dCEF720 with WS-F6700-DFC3B (adds 2.70 A@42 V)

dCEF720 with WS-F6700-DFC3A (adds 3.00 A@42 V)

Supports egress multicast replication

QoS port architecture (Rx/Tx):

With DFC3: 8q8t/1p7q8t

With CFC: 1q8t/1p7q8t

Dual switch-fabric connections
Fabric Channel #1: Ports 3 and 4
Fabric Channel #2: Ports 1 and 2

Number of ports: 4
Number of port groups: 4
Port ranges per port group: 1 port in each group

 

Supported only with Supervisor Engine 720

12.2(17a)SX

Note

To use Cisco IOS Software Modularity images with 6700 series switching modules, ensure that the 6700 series switching modules have switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html

WS-X6704-10GE requires one of the following:

WS-F6700-DFC3BXL (3.30 A@42 V)

WS-F6700-DFC3B (2.70 A@42 V)

WS-F6700-DFC3A (3.00 A@42 V)

WS-F6700-CFC (0.75 A@42 V)

WS-X6704-10GE ships with WS-F6700-CFC installed unless ordered with WS-F6700-DFC3BXL, WS-F6700-DFC3B, or WS-F6700-DFC3A.

WS-X6704-10GE is supported in the WS-C6503-E chassis.

WS-X6704-10GE is not supported in the WS-C6503 and CISCO7603 chassis.

In a 13-slot chassis, WS-X6704-10GE is supported only in slots 9 through 13 and does not power up in other slots.

On WS-X6704-10GE ports, STP BPDUs are not exempt from Traffic Storm Control multicast suppression. Do not configure multicast suppression on STP-protected WS-X6704-10GE ports that interconnect network devices. (CSCsg86315)

WS-X6502-10GE

3.30 A@42 V

1-port 10-Gigabit Ethernet

With Supervisor Engine 720:

dCEF256 with WS-F6K-DFC3BXL (adds 1.47 A@42 V)

dCEF256 with WS-F6K-DFC3B (adds 1.67 A@42 V)

dCEF256 with WS-F6K-DFC3A (adds 2.57 A@42 V)

With Supervisor Engine 2, dCEF256 with WS-F6K-DFC (adds 2.10 A@42 V)

QoS port architecture (Rx/Tx): 1p1q8t/1p2q1t

Number of ports: 1
Number of port groups: 1
Port ranges per port group: 1 port in 1 group

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

Note WS-X6502-10GE does not support ISL encapsulation.

Optical Interface Module (OIM) for WS-X6502-10GE
 WS-G6488

10GBASE-LR serial 1310 nm long-reach OIM

12.2(14)SX

 WS-G6483

10GBASE-ER serial 1550 nm extended-reach OIM

12.2(14)SX


Gigabit Ethernet Switching Modules

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-X6748-SFP

5.32 A@42 V

48-port Gigabit Ethernet SFP

CEF720 with WS-F6700-CFC (adds 0.75 A@42 V)

dCEF720 with WS-F6700-DFC3BXL (adds 3.30 A@42 V)

dCEF720 with WS-F6700-DFC3B (adds 2.70 A@42 V)

dCEF720 with WS-F6700-DFC3A (adds 3.00 A@42 V)

Supports egress multicast replication

QoS architecture:

With DFC3: 2q8t/1p3q8t

With CFC: 1q8t/1p3q8t

Dual switch-fabric connections
Fabric Channel #1: Ports 2, 4, 6, 8, 10, 12,
14, 16, 18, 20, 22, 24, 26, 28, 30, 32, 34,
36, 38, 40, 42, 44, 46, 48
Fabric Channel #2: Ports 1, 3, 5, 7, 9, 11,
13, 15, 17, 19, 21, 23, 25, 27, 29, 31, 33,
35, 37, 39, 41, 43, 45, 47

Number of ports: 48
Number of port groups: 4
Port ranges per port group:
 1,  3,  5,  7,  9, 11, 13, 15, 17, 19, 21, 23
 2,  4,  6,  8, 10, 12, 14, 16, 18, 20, 22, 24
25, 27, 29, 31, 33, 35, 37, 39, 41, 43, 45, 47
26, 28, 30, 32, 34, 36, 38, 40, 42, 44, 46, 48

 

Supported only with Supervisor Engine 720

12.2(17d)SXB

Note

To use Cisco IOS Software Modularity images with 6700 series switching modules, ensure that the 6700 series switching modules have switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html

WS-X6748-SFP requires one of the following:

WS-F6700-DFC3BXL (3.30 A@42 V)

WS-F6700-DFC3B (2.70 A@42 V)

WS-F6700-DFC3A (3.00 A@42 V)

WS-F6700-CFC (0.75 A@42 V)

WS-X6748-SFP ships with WS-F6700-CFC installed unless ordered with WS-F6700-DFC3BXL, WS-F6700-DFC3B, or WS-F6700-DFC3A.

WS-X6748-SFP is supported in the WS-C6503-E chassis.

WS-X6748-SFP is not supported in the WS-C6503 and CISCO7603 chassis.

In a 13-slot chassis, WS-X6748-SFP is supported only in slots 9 through 13 and does not power up in other slots.

On WS-X6748-SFP ports, STP BPDUs are not exempt from Traffic Storm Control multicast suppression. Do not configure multicast suppression on STP-protected WS-X6748-SFP ports that interconnect network devices. (CSCsg86315)

See the "Small Form-Factor Pluggable (SFP) Modules" section.

WS-X6724-SFP

2.23 A@42 V

24-port Gigabit Ethernet SFP

CEF720 with WS-F6700-CFC (adds 0.75 A@42 V)

dCEF720 with WS-F6700-DFC3BXL (adds 3.30 A@42 V)

dCEF720 with WS-F6700-DFC3B (adds 2.70 A@42 V)

dCEF720 with WS-F6700-DFC3A (adds 3.00 A@42 V)

Supports egress multicast replication

QoS architecture:

With DFC3: 2q8t/1p3q8t

With CFC: 1q8t/1p3q8t

Number of ports: 24
Number of port groups: 2
Port ranges per port group: 1-12, 13-24

 

Supported only with Supervisor Engine 720

12.2(17a)SX

WS-X6724-SFP HW rev 2.3 or later (supported only with Supervisor Engine 720)

12.2(17d)SXB1

Note

To use Cisco IOS Software Modularity images with 6700 series switching modules, ensure that the 6700 series switching modules have switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html

WS-X6724-SFP requires one of the following:

WS-F6700-DFC3BXL (3.30 A@42 V)

WS-F6700-DFC3B (2.70 A@42 V)

WS-F6700-DFC3A (3.00 A@42 V)

WS-F6700-CFC (0.75 A@42 V)

WS-X6724-SFP ships with WS-F6700-CFC installed unless ordered with WS-F6700-DFC3BXL, WS-F6700-DFC3B, or WS-F6700-DFC3A.

WS-X6724-SFP is supported in the WS-C6503-E chassis.

WS-X6724-SFP is not supported in the WS-C6503 and CISCO7603 chassis.

WS-X6724-SFP is supported in all slots of a 13-slot chassis.

On WS-X6724-SFP ports, STP BPDUs are not exempt from Traffic Storm Control multicast suppression. Do not configure multicast suppression on STP-protected WS-X6724-SFP ports that interconnect network devices. (CSCsg86315)

See the "Small Form-Factor Pluggable (SFP) Modules" section.

WS-X6816-GBIC
 

16-port Gigabit Ethernet GBIC

dCEF256

QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t

Dual switch-fabric connections
Fabric Channel #1: Ports 1-8
Fabric Channel #2: Ports 9-16

Number of ports: 16
Number of port groups: 2
Port ranges per port group: 1-8, 9-16

 

3.84 A@42 V

With Supervisor Engine 720

12.2(14)SX

5.94 A@42 V

With Supervisor Engine 2

12.2(17d)SXB

Note

WS-X6816-GBIC requires one of these for use with Supervisor Engine 720:

WS-F6K-DFC3BXL (adds 1.47 A@42 V)

WS-F6K-DFC3B (adds 1.67 A@42 V)

WS-F6K-DFC3A (adds 2.57 A@42 V)

WS-X6816-GBIC requires WS-F6K-DFC for use with Supervisor Engine 2.

In a 13-slot chassis, WS-X6816-GBIC is supported only in slots 9 through 13 and does not power up in other slots.

WS-X6516A-GBIC

3.62 A@42 V

16-port Gigabit Ethernet GBIC

CEF256

With Supervisor Engine 720:

dCEF256 with WS-F6K-DFC3BXL (adds 1.47 A@42 V)

dCEF256 with WS-F6K-DFC3B (adds 1.67 A@42 V)

dCEF256 with WS-F6K-DFC3A (adds 2.57 A@42 V)

With Supervisor Engine 2, dCEF256 with WS-F6K-DFC (adds 2.10 A@42 V)

1-MB per-port packet buffers

Supports egress multicast replication

QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t

Number of ports: 16
Number of port groups: 2
Port ranges per port group: 1-8, 9-16

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-X6516-GBIC

3.40 A@42 V

16-port Gigabit Ethernet GBIC

CEF256

With Supervisor Engine 720:

dCEF256 with WS-F6K-DFC3BXL (adds 1.47 A@42 V)

dCEF256 with WS-F6K-DFC3B (adds 1.67 A@42 V)

dCEF256 with WS-F6K-DFC3A (adds 2.57 A@42 V)

With Supervisor Engine 2, dCEF256 with WS-F6K-DFC (adds 2.10 A@42 V)

512-KB per-port packet buffers

QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t

Number of ports: 16
Number of port groups: 2
Port ranges per port group: 1-8, 9-16

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

Note

Supervisor Engine 720 supports a DFC3 on these WS-X6516-GBIC hardware revisions:

Lower than 5.0

5.5 and higher

Supervisor Engine 720 does not support a DFC3 on WS-X6516-GBIC hardware revisions 5.0 through 5.4. With a Supervisor Engine 720 and with a DFC3 installed, WS-X6516-GBIC hardware revisions 5.0 through 5.4 do not power up.

With a Supervisor Engine 720 but without a DFC3, WS-X6516-GBIC hardware revisions 5.0 through 5.4 operate in bus mode.

See external field notice 24494 for more information:

http://www.cisco.com/en/US/ts/fn/200/fn24494.html

WS-X6416-GBIC

2.81 A@42 V

16-port Gigabit Ethernet GBIC

QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t

Number of ports: 16
Number of port groups: 2
Port ranges per port group: 1-8, 9-16

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-X6416-GE-MT

2.50 A@42 V

16-Port Gigabit Ethernet MT-RJ

QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t

Number of ports: 16
Number of port groups: 2
Port ranges per port group: 1-8, 9-16

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-X6316-GE-TX

5.15 A@42 V

16-port Gigabit Ethernet RJ-45

QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t

Number of ports: 16
Number of port groups: 2
Port ranges per port group: 1-8, 9-16

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-X6408A-GBIC

2.00 A@42 V

8-port Gigabit Ethernet GBIC

QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t

Number of ports: 8
Number of port groups: 1
Port ranges per port group: 1-8

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-X6408-GBIC

2.00 A@42 V

8-port Gigabit Ethernet GBIC

QoS port architecture (Rx/Tx): 1q4t/2q2t

Number of ports: 8
Number of port groups: 1
Port ranges per port group: 1-8

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

Note

Caveat CSCec65943 prevents support of the WS-X6408-GBIC switching module in Release 12.2(17a)SX.

Caveat CSCec65943 is resolved in Release 12.2(17a)SX1 and later releases.


Power over Ethernet Daughtercards


Note The power over Ethernet (PoE) daughtercard "Power Required" values do not include the power drawn by phones.


Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-F6K-FE48X2-AF

0.42 A@42 V

IEEE 802.3af PoE daughtercard for WS-X6148X2-RJ-45 and WS-X6196-RJ-21.

 

With Supervisor Engine 720

12.2(18)SXF

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(18)SXF2

WS-F6K-GE48-AF
WS-F6K-48-AF

0.18 A@42 V

IEEE 802.3af PoE daughtercard for:

WS-X6548-GE-TX

WS-X6148-GE-TX

WS-X6148A-GE-TX

WS-X6148A-RJ-45

Note

WS-F6K-GE48-AF and WS-F6K-48-AF are not FRUs for these switching modules:

WS-X6148-RJ-45 or WS-X6148-RJ-45V (replace with WS-X6148-45AF-UG=).

WS-X6148-RJ-21 or WS-X6148-RJ-21V (replace with WS-X6148-21AF-UG=).

 

With Supervisor Engine 720

12.2(17d)SXB

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-F6K-VPWR-GE

0.42 A@42 V

PoE daughtercard for WS-X6548-GE-TX and WS-X6148-GE-TX

 

With Supervisor Engine 720

12.2(17a)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-F6K-VPWR

None

PoE daughtercard for:

WS-X6348-RJ-45

WS-X6348-RJ-21V

WS-X6148-RJ-45

WS-X6148-RJ-21

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB


10/100/1000 Ethernet Switching Modules

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-X6748-GE-TX

7.00 A@42 V

48-port 10/100/1000 RJ-45

CEF720 with WS-F6700-CFC (adds 0.75 A@42 V)

dCEF720 with WS-F6700-DFC3BXL (adds 3.30 A@42 V)

dCEF720 with WS-F6700-DFC3B (adds 2.70 A@42 V)

dCEF720 with WS-F6700-DFC3A (adds 3.00 A@42 V)

Supports egress multicast replication

QoS architecture:

With DFC3: 2q8t/1p3q8t

With CFC: 1q8t/1p3q8t

Dual switch-fabric connections
Fabric Channel #1: Ports 25-48
Fabric Channel #2: Ports 1-24

Number of ports: 48
Number of port groups: 4
Port ranges per port group: 1-12, 13-24, 25-36, 37-48

 

Supported only with Supervisor Engine 720

12.2(17a)SX

Note

To use Cisco IOS Software Modularity images with 6700 series switching modules, ensure that the 6700 series switching modules have switching module ROMMON version 12.2(18r)S1 or later. To display the switching module ROMMON version, enter the remote command module module_slot_number show version | include ROM command. To upgrade the switching module ROMMON, see this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/rommon/OL_6143.html

WS-X6748-GE-TX requires one of the following:

WS-F6700-DFC3BXL (3.30 A@42 V)

WS-F6700-DFC3B (2.70 A@42 V)

WS-F6700-DFC3A (3.00 A@42 V)

WS-F6700-CFC (0.75 A@42 V)

WS-X6748-GE-TX ships with WS-F6700-CFC installed unless ordered with WS-F6700-DFC3BXL, WS-F6700-DFC3B, or WS-F6700-DFC3A.

WS-X6748-GE-TX is supported in the WS-C6503-E chassis.

WS-X6748-GE-TX is not supported in the WS-C6503 and CISCO7603 chassis.

In a 13-slot chassis, WS-X6748-GE-TX is supported only in slots 9 through 13 and does not power up in other slots.

On WS-X6748-GE-TX ports, STP BPDUs are not exempt from Traffic Storm Control multicast suppression. Do not configure multicast suppression on STP-protected WS-X6748-GE-TX ports that interconnect network devices. (CSCsg86315)

WS-X6548-GE-TX

2.98 A@42 V

48-port 10/100/1000 Mbps

RJ-45

CEF256

WS-X6548-GE-TX supports:

WS-F6K-VPWR-GE

WS-F6K-GE48-AF

WS-F6K-48-AF

WS-X6548V-GE-TX has WS-F6K-VPWR-GE

WS-X6548-GE-45AF has WS-F6K-GE48-AF or WS-F6K-48-AF

QoS port architecture (Rx/Tx): 1q2t/1p2q2t

Number of ports: 48
Number of port groups: 2
Port ranges per port group: 1-24, 25-48

The aggregate bandwidth of each set of 8 ports (1-8, 9-16, 17-24, 25-32, 33-40, and 41-48) is 1 Gbps.

WS-X6548V-GE-TX

3.40 A@42 V

WS-X6548-GE-45AF

3.16 A@42 V

 

With Supervisor Engine 720
(except WS-F6K-GE48-AF or WS-F6K-48-AF)

12.2(17a)SX

WS-F6K-GE48-AF or WS-F6K-48-AF
with Supervisor Engine 720

12.2(17d)SXB

With Supervisor Engine 32

12.2(18)SXF

WS-F6K-GE48-AF or WS-F6K-48-AF
with Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-F6K-GE48-AF or WS-F6K-48-AF
with Supervisor Engine 2

12.2(17d)SXB

Note

Release 12.2(17b)SXA and later releases provide support for more than 1 Gbps of traffic per EtherChannel on the WS-X6548-GE-TX (and voice-power daughtercard equipped) switching modules.

WS-X6548-GE-TX and WS-X6548V-GE-TX do not support these features:

With Release 12.2(17a)SX and Release 12.2(17a)SX1, more than 1 Gbps of traffic per EtherChannel

DFCs

ISL trunking

Jumbo frames

802.1Q tunneling

Traffic storm control

WS-X6148A-GE-TX

2.50 A@42 V

48-port 10/100/1000 Mbps

RJ-45

WS-X6148A-GE-TX supports WS-F6K-GE48-AF or WS-F6K-48-AF

WS-X6148A-GE-45AF has WS-F6K-GE48-AF or WS-F6K-48-AF

QoS port architecture (Rx/Tx): 1q2t/1p3q8t

Number of ports: 48
Number of port groups: 6
Port ranges per port group: 1-8, 9-16, 17-24, 25-32, 33-40, 41-48

The aggregate bandwidth of each port group is 1 Gbps.

WS-X6148A-GE-45AF

2.68 A@42 V

 

With Supervisor Engine 720

12.2(18)SXF

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(18)SXF2

Note WS-X6148A-GE-TX and WS-X6148A-GE-45AF do not support these features:

WS-F6K-DFC3A, WS-F6K-DFC3B, or WS-F6K-DFC3BXL

Traffic storm control

WS-X6148-GE-TX

2.47 A@42 V

48-port 10/100/1000 Mbps

RJ-45

WS-X6148-GE-TX supports:

WS-F6K-VPWR-GE

WS-F6K-GE48-AF

WS-F6K-48-AF

WS-X6148V-GE-TX has WS-F6K-VPWR-GE

WS-X6148-GE-45AF has WS-F6K-GE48-AF or WS-F6K-48-AF

QoS port architecture (Rx/Tx): 1q2t/1p2q2t

Number of ports: 48
Number of port groups: 2
Port ranges per port group: 1-24, 25-48

The aggregate bandwidth of each set of 8 ports (1-8, 9-16, 17-24, 25-32, 33-40, and 41-48) is 1 Gbps.

WS-X6148V-GE-TX

2.89 A@42 V

WS-X6148-GE-45AF

2.65 A@42 V

 

With Supervisor Engine 720
(except WS-F6K-GE48-AF or WS-F6K-48-AF)

12.2(17a)SX

WS-F6K-GE48-AF or WS-F6K-48-AF
with Supervisor Engine 720

12.2(17d)SXB

With Supervisor Engine 32

12.2(18)SXF

WS-F6K-GE48-AF or WS-F6K-48-AF
with Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-F6K-GE48-AF or WS-F6K-48-AF
with Supervisor Engine 2

12.2(17d)SXB

Note WS-X6148-GE-TX, WS-X6148V-GE-TX, and WS-X6148-GE-45AF do not support these features:

More than 1 Gbps of traffic per EtherChannel

WS-F6K-DFC3A, WS-F6K-DFC3B, or WS-F6K-DFC3BXL

ISL trunking

Jumbo frames

802.1Q tunneling

Traffic storm control

WS-X6516-GE-TX

3.45 A@42 V

16-port 10/100/1000BASE-T

CEF256

With Supervisor Engine 720:

dCEF256 with WS-F6K-DFC3BXL (adds 1.47 A@42 V)

dCEF256 with WS-F6K-DFC3B (adds 1.67 A@42 V)

dCEF256 with WS-F6K-DFC3A (adds 2.57 A@42 V)

With Supervisor Engine 2, dCEF256 with WS-F6K-DFC (adds 2.10 A@42 V)

QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t

Number of ports: 16
Number of port groups: 2
Port ranges per port group: 1-8, 9-16

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB


Fast Ethernet Switching Modules

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-X6148-FE-SFP

2.30 A@42 V

48-port 100BASE-FX

Requires Fast Ethernet SFPs

QoS port architecture (Rx/Tx): 1p1q4t/1p3q8t

Number of ports: 48
Number of port groups: 3
Port ranges per port group: 1-16, 17-32, and 33-48

 

With Supervisor Engine 720

12.2(18)SXF

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(18)SXF2

WS-X6524-100FX-MM

1.90 A@42 V

24-port 100FX Ethernet multimode

CEF256

With Supervisor Engine 720:

dCEF256 with WS-F6K-DFC3BXL (adds 1.47 A@42 V)

dCEF256 with WS-F6K-DFC3B (adds 1.67 A@42 V)

dCEF256 with WS-F6K-DFC3A (adds 2.57 A@42 V)

With Supervisor Engine 2, dCEF256 with WS-F6K-DFC (adds 2.10 A@42 V)

QoS port architecture (Rx/Tx): 1p1q0t/1p3q1t

Number of ports: 24
Number of port groups: 1
Port ranges per port group: 1-24

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-X6324-100FX-SM

1.52 A@42 V

24-port 100FX Ethernet

Single mode and multimode MT-RJ

128-KB per-port packet buffers

QoS port architecture (Rx/Tx): 1q4t/2q2t

Number of ports: 24
Number of port groups: 2
Port ranges per port group: 1-12, 13-24

WS-X6324-100FX-MM

1.52 A@42 V

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-X6224-100FX-MT

1.90 A@42 V

24-port 100FX Ethernet Multimode MT-RJ

QoS port architecture (Rx/Tx): 1q4t/2q2t

Number of ports: 24
Number of port groups: 2
Port ranges per port group: 1-12, 13-24

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB


Ethernet/Fast Ethernet (10/100) Switching Modules

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-X6548-RJ-45

2.90 A@42 V

48-port 10/100TX RJ-45

CEF256

With Supervisor Engine 720:

dCEF256 with WS-F6K-DFC3BXL (adds 1.47 A@42 V)

dCEF256 with WS-F6K-DFC3B (adds 1.67 A@42 V)

dCEF256 with WS-F6K-DFC3A (adds 2.57 A@42 V)

With Supervisor Engine 2, dCEF256 with WS-F6K-DFC (adds 2.10 A@42 V)

QoS port architecture (Rx/Tx): 1p1q0t/1p3q1t

Number of ports: 48
Number of port groups: 1
Port ranges per port group: 1-48

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-X6548-RJ-21

2.90 A@42 V

48-port 10/100TX RJ-21

CEF256

With Supervisor Engine 720:

dCEF256 with WS-F6K-DFC3BXL (adds 1.47 A@42 V)

dCEF256 with WS-F6K-DFC3B (adds 1.67 A@42 V)

dCEF256 with WS-F6K-DFC3A (adds 2.57 A@42 V)

With Supervisor Engine 2, dCEF256 with WS-F6K-DFC (adds 2.10 A@42 V)

QoS port architecture (Rx/Tx): 1p1q0t/1p3q1t

Number of ports: 48
Number of port groups: 1
Port ranges per port group: 1-48

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-X6148X2-RJ-45

2.65 A@42 V

96-port 10/100TX RJ-45

QoS port architecture (Rx/Tx): 1p1q0t/1p3q1t

WS-X6148X2-RJ-45 supports WS-F6K-FE48X2-AF

WS-X6148X2-45AF has WS-F6K-FE48X2-AF

WS-X6148X2-45AF

3.07 A@42 V

 

With Supervisor Engine 720

12.2(18)SXF3

With Supervisor Engine 32

12.2(18)SXF3

With Supervisor Engine 2

12.2(18)SXF3

WS-X6196-RJ-21

2.74 A@42 V

96-port 10/100TX RJ-21

QoS port architecture (Rx/Tx): 1p1q0t/1p3q1t

WS-X6196-RJ-21 supports WS-F6K-FE48X2-AF

WS-X6196-21AF has WS-F6K-FE48X2-AF

WS-X6196-21AF

3.16 A@42 V

 

With Supervisor Engine 720

12.2(18)SXF3

With Supervisor Engine 32

12.2(18)SXF3

With Supervisor Engine 2

12.2(18)SXF3

WS-X6348-RJ-45

2.39 A@42 V

48-port 10/100TX RJ-45

128-KB per-port packet buffers

QoS port architecture (Rx/Tx): 1q4t/2q2t

WS-X6348-RJ-45 supports WS-F6K-VPWR

WS-X6348-RJ-45V has WS-F6K-VPWR

Number of ports: 48
Number of port groups: 4
Port ranges per port group: 1-12, 13-24, 25-36, 37-48

WS-X6348-RJ-45V

2.39 A@42 V

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-X6348-RJ-21V

2.39 A@42 V

48-port 10/100TX RJ-21

128-KB per-port packet buffers

QoS port architecture (Rx/Tx): 1q4t/2q2t

Has WS-F6K-VPWR

Number of ports: 48
Number of port groups: 4
Port ranges per port group: 1-12, 13-24, 25-36, 37-48

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-X6248-RJ-45

2.69 A@42 V

48-port 10/100TX RJ-45

QoS port architecture (Rx/Tx): 1q4t/2q2t

Number of ports: 48
Number of port groups: 4
Port ranges per port group: 1-12, 13-24, 25-36, 37-48

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-X6248A-TEL

2.69 A@42 V

48-port 10/100TX RJ-21

128-KB per-port packet buffers

QoS port architecture (Rx/Tx): 1q4t/2q2t

Number of ports: 48
Number of port groups: 4
Port ranges per port group: 1-12, 13-24, 25-36, 37-48

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-X6248-TEL

2.69 A@42 V

48-port 10/100TX RJ-21

QoS port architecture (Rx/Tx): 1q4t/2q2t

Number of ports: 48
Number of port groups: 4
Port ranges per port group: 1-12, 13-24, 25-36, 37-48

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-X6148A-RJ-45

1.00 A@42 V

48-port 10/100TX RJ-45

5.3-MB per-port packet buffers

QoS port architecture (Rx/Tx): 1p1q4t/1p3q8t

WS-X6148A-RJ-45 supports WS-F6K-GE48-AF or WS-F6K-48-AF

WS-X6148A-45AF has WS-F6K-GE48-AF or WS-F6K-48-AF

Number of ports: 48
Number of port groups: 6
Port ranges per port group: 1-8, 9-16, 17-24, 25-32, 33-40, 41-48

WS-X6148A-45AF

2.57 A@42 V

 

With Supervisor Engine 720

12.2(18)SXF

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(18)SXF2

WS-X6148-RJ-45

2.39 A@42 V

48-port 10/100TX RJ-45

128-KB per-port packet buffers

QoS port architecture (Rx/Tx): 1q4t/2q2t

WS-X6148-RJ-45 supports WS-F6K-VPWR

WS-X6148-RJ-45V has WS-F6K-VPWR

WS-X6148-45AF has WS-F6K-48-AF

Number of ports: 48
Number of port groups: 4
Port ranges per port group: 1-12, 13-24, 25-36, 37-48

WS-X6148-RJ45V

2.39 A@42 V

WS-X6148-45AF

2.57 A@42 V

 

With Supervisor Engine 720
(except with WS-F6K-48-AF)

12.2(14)SX

WS-F6K-48-AF with Supervisor Engine 720

12.2(17d)SXB

With Supervisor Engine 32

12.2(18)SXF

WS-F6K-48-AF with Supervisor Engine 32

With Supervisor Engine 2

12.2(17d)SXB

WS-F6K-48-AF with Supervisor Engine 2

WS-X6148-RJ-21

2.39 A@42 V

48-port 10/100TX RJ-21

128-KB per-port packet buffers

QoS port architecture (Rx/Tx): 1q4t/2q2t

WS-X6148-RJ-21 supports WS-F6K-VPWR

WS-X6148-RJ-21V has WS-F6K-VPWR

WS-X6148-21AF has WS-F6K-48-AF

Number of ports: 48
Number of port groups: 4
Port ranges per port group: 1-12, 13-24, 25-36, 37-48

WS-X6148-RJ21V

2.39 A@42 V

WS-X6148-21AF

2.57 A@42 V

 

With Supervisor Engine 720
(except with WS-F6K-48-AF)

12.2(14)SX

WS-F6K-48-AF with Supervisor Engine 720

12.2(17d)SXB

With Supervisor Engine 32

12.2(18)SXF

WS-F6K-48-AF with Supervisor Engine 32

With Supervisor Engine 2

12.2(17d)SXB

WS-F6K-48-AF with Supervisor Engine 2


Ethernet Switching Modules

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-X6024-10FL-MT

1.52 A@42 V

24-port 10BASE-FL MT-RJ

QoS port architecture (Rx/Tx): 1q4t/2q2t

Number of ports: 24
Number of port groups: 2
Port ranges per port group: 1-12, 13-24

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB


Optical Services Modules (OSMs)

OSM Guidelines and Restrictions

Gigabit Ethernet WAN

OC-48 Packet over SONET

OC-48 DPT/Packet over SONET

OC-12 Packet over SONET

OC-3 Packet over SONET

OC-12 Channelized

CT3/T1 Channelized/Unchannelized

OC-12 ATM

OSM Guidelines and Restrictions

Cisco IOS Software modularity does not support OSMs.

Supervisor Engine 32 does not support OSMs.

With Release 12.2(18)SXD and later releases, OSMs require a minimum of 128 MB of dynamic random-access memory (SDRAM)—See this publication for memory upgrade procedures:

http://www.cisco.com/en/US/docs/routers/7600/Hardware/Module_and_Line_Card_Installation_Guides/7600_Series_Router_Module_Installation_Guide/osmodule.html

OSMs are CEF256 modules.

OSM WAN port numbering starts with 1.

On OSMs with Gigabit Ethernet GBIC Layer 2 LAN ports:

OSM LAN port numbering starts with 1.

The LAN ports are in a single port group.

In releases earlier than Release 12.2(18)SXD1, WS-SVC-WLAN-1-K9 has not been tested with OSMs.

The OSM-2+4GE-WAN+ and the OC-12 Packet-over-SONET OSMs have been tested with the service modules and WS-SUP720.

In releases earlier than Release 12.2(18)SXD1, except for the OSM-2+4GE-WAN+ and the OC-12 Packet-over-SONET OSMs, the following service modules have not been tested with other OSMs:

WS-X6066-SLB-APC content switching module (CSM)

WS-SVC-IDSM2-K9 intrusion detection system module

WS-SVC-NAM-2 and WS-SVC-NAM-1 network analysis modules (NAMs)

WS-SVC-SSL-1 SSL services module

Gigabit Ethernet WAN

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
OSM-4GE-WAN-GBIC

3.59 A@42 V

4-port Gigabit Ethernet WAN (GBIC); CEF256

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB

OSM-2+4GE-WAN+

5.08 A@42 V

4-port Gigabit Ethernet WAN (GBIC) with two Layer 2 LAN ports; CEF256

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB


OC-48 Packet over SONET


Note Also has four Layer 2 LAN ports.


Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
OSM-1OC48-POS-SS
OSM-1OC48-POS-SI
OSM-1OC48-POS-SL

4.25 A@42 V

1-port OC-48/STM-16 SONET/SDH OSM, SM-SR; CEF256
1-port OC-48/STM-16 SONET/SDH OSM, SM-IR; CEF256
1-port OC-48/STM-16 SONET/SDH OSM, SM-LR; CEF256

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB

OSM-1OC48-POS-SI+
OSM-1OC48-POS-SL+
OSM-1OC48-POS-SS+

3.90 A@42 V

Enhanced 1-port OC-48/STM-16 SONET/SDH OSM, SM-IR; CEF256
Enhanced 1-port OC-48/STM-16 SONET/SDH OSM, SM-LR; CEF256
Enhanced 1-port OC-48/STM-16 SONET/SDH OSM, SM-SR; CEF256

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB


OC-48 DPT/Packet over SONET


Note Also has four Layer 2 LAN ports.


Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
OSM-2OC48/1DPT-SS
OSM-2OC48/1DPT-SI
OSM-2OC48/1DPT-SL

5.75 A@42 V

2-port OC-48 DPT/POS, SM-SR; CEF256
2-port OC-48 DPT/POS, SM-IR; CEF256
2-port OC-48 DPT/POS, SM-LR; CEF256

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB


OC-12 Packet over SONET


Note Also has four Layer 2 LAN ports.


Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
OSM-4OC12-POS-MM
OSM-4OC12-POS-SI
OSM-4OC12-POS-SL

4.78 A@42 V

4-port OC-12c/STM-4c POS, MM; CEF256
4-port OC-12c/STM-4c POS, SM-IR; CEF256
4-port OC-12c/STM-4c POS, SM-LR; CEF256

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB

OSM-4OC12-POS-SI+

4.55 A@42 V

Enhanced 4-port OC-12c/STM-4c POS, SM-IR; CEF256

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB

OSM-2OC12-POS-MM+
OSM-2OC12-POS-MM
OSM-2OC12-POS-SI
OSM-2OC12-POS-SL

3.36 A@42 V

2-port OC-12c/STM-4c POS, MM; CEF256
2-port OC-12c/STM-4c POS, MM; CEF256
2-port OC-12c/STM-4c POS, SM-IR; CEF256
2-port OC-12c/STM-4c POS, SM-LR; CEF256

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB

OSM-2OC12-POS-SI+

3.36 A@42 V

Enhanced 2-port OC-12c/STM-4c POS, SM-IR; CEF256

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB


OC-3 Packet over SONET


Note Also has four Layer 2 LAN ports.


Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
OSM-16OC3-POS-MM
OSM-16OC3-POS-SI
OSM-16OC3-POS-SL

5.09 A@42 V

16-port OC-3c/STM-1c POS, MM; CEF256
16-port OC-3c/STM-1c POS, SM-IR; CEF256
16-port OC-3c/STM-1c POS, SM-LR; CEF256

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB

OSM-16OC3-POS-SI+

4.80 A@42 V

Enhanced 16-port OC-3c/STM-1c POS, SM-IR; CEF256

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB

OSM-8OC3-POS-MM
OSM-8OC3-POS-SI
OSM-8OC3-POS-SL

3.57 A@42 V

8-port OC-3c/STM-1c POS, MM; CEF256
8-port OC-3c/STM-1c POS, SM-IR; CEF256
8-port OC-3c/STM-1c POS, SM-LR; CEF256

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB

OSM-8OC3-POS-SI+
OSM-8OC3-POS-SL+

3.57 A@42 V

Enhanced 8-port OC-3c/STM-1c POS, SM-IR; CEF256
Enhanced 8-port OC-3c/STM-1c POS, SM-LR; CEF256

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB

OSM-4OC3-POS-SI

2.44 A@42 V

4-port OC-3c/STM-1c POS, SM-IR; CEF256

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB

OSM-4OC3-POS-SI+

2.44 A@42 V

Enhanced 4-port OC-3c/STM-1c POS, SM-IR; CEF256

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB


OC-12 Channelized


Note Also has four Layer 2 LAN ports.


Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
OSM-1CHOC12/T3-SI
OSM-1CHOC12/T1-SI

4.40 A@42 V
2.80 A@42 V

1-port channelized OC-12, SM-IR; CEF256
1-port channelized OC-12, SM-IR; CEF256

 
 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB


CT3/T1 Channelized/Unchannelized


Note OSM-12CT3/T1 has mini-SMB connectors for use with 75-Ohm copper coax cable.


Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
OSM-12CT3/T1

2.80 A@42 V

12-port channelized/unchannelized CT3/T1; CEF256

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB


OC-12 ATM


Note Also has four Layer 2 LAN ports.


Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
OSM-2OC12-ATM-MM
OSM-2OC12-ATM-SI

3.62 A@42 V

2-port OC-12/STM-4 ATM OSM, MM; CEF256
2-port OC-12/STM-4 ATM OSM, SM-IR; CEF256

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB

OSM-2OC12-ATM-MM+
OSM-2OC12-ATM-SI+

4.00 A@42 V

Enhanced 2-port OC-12/STM-4 ATM OSM, MM; CEF256
Enhanced 2-port OC-12/STM-4 ATM OSM, SM-IR; CEF256

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB


Shared Port Adapter (SPA) Interface Processors (SIPs)


NoteSee the "FPD Image Packages" section for information about additional procedures required to support SIPs with Release 12.2(18)SXE and later releases.

7600-SIP-400 and 7600-SIP-600 are not supported in PFC3A mode.

With releases earlier than Release 12.2(18)SXF7, Cisco IOS Software modularity does not support SIPs.

In Release 12.2(18)SXF7 and later releases, Cisco IOS Software Modularity supports 7600-SIP-400 and 7600-SIP-200.


Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
7600-SIP-600

8.14 A@42 V

SPA Interface Processor-600 (not supported in PFC3A mode)

Note 7600-SIP-600 has a WS-F6700-DFC3BXL.

Supported only with Supervisor Engine 720

12.2(18)SXF

Note

Supervisor Engine 32 does not support 7600-SIP-600.

7600-SIP-600 is not supported when a 7600-SSC-400 and SPA-IPSEC-2G are installed.

7600-SIP-600 is not supported in Release 12.2(33)SXH and rebuilds.

7600-SIP-400

6.31 A@42 V

SPA Interface Processor-400 (not supported in PFC3A mode)

With Supervisor Engine 720

12.2(18)SXE

With Supervisor Engine 32

12.2(18)SXF

7600-SIP-200

5.72 A@42 V

SPA Interface Processor-200

With Supervisor Engine 720

12.2(18)SXE

With Supervisor Engine 32

12.2(18)SXF


Shared Port Adapters (SPAs)

These sections describe SPAs:

Ethernet SPAs

POS SPAs

ATM SPAs

SFPs for OC3 and OC12 POS and ATM SPAs

Serial SPAs


NoteWith releases earlier than Release 12.2(18)SXF7, Cisco IOS Software modularity does not support SIPs.

In Release 12.2(18)SXF7 and later releases, Cisco IOS Software Modularity supports 7600-SIP-400 and 7600-SIP-200.


Ethernet SPAs

These sections describe Ethernet SPAs:

10-Gigabit Ethernet SPAs

Gigabit Ethernet SPAs

10-Gigabit Ethernet SPAs

Product ID
(append "=" for spares)
SIP Support
Product Description
Minimum Software Version
SPA-1XTENGE-XFP

7600-SIP-600

1-port 10-Gigabit Ethernet SPA, LANPHY XFP Optics

12.2(18)SXF

XFP Modules Supported in SPA-1XTENGE-XFP
 XFP-10GLR-OC192LR

10-Gigabit Ethernet LR (10 km)


Gigabit Ethernet SPAs

Product ID
(append "=" for spares)
SIP Support
Product Description
Minimum Software Version
SPA-10X1GE

7600-SIP-600

10-port Gigabit Ethernet SPA, SFP Optics

12.2(18)SXF

SPA-5X1GE

7600-SIP-600

5-port Gigabit Ethernet SPA, SFP Optics

12.2(18)SXF

SPA-2X1GE

7600-SIP-400

2-port Gigabit Ethernet SPA, SFP Optics

12.2(18)SXF

SFPs Supported in Gigabit Ethernet SPAs
 SFP-GE-S

Extended Temperature SX SFP

 SFP-GE-L

Extended Temperature LX/LH SFP

 SFP-GE-Z

Extended Temperature ZX SFP


POS SPAs

Product ID
(append "=" for spares)
SIP Support
Product Description
Minimum Software Version
SPA-1XOC48POS/RPR

7600-SIP-400

1-Port OC-48 POS/RPR SPA

Note Requires SFPs.

12.2(18)SXF10

SPA-OC192POS-VSR

7600-SIP-600

1-port OC-192c/STM-64 POS/RPR SPA, VSR-1

12.2(18)SXF2

SPA-2XOC3-POS

7600-SIP-200
7600-SIP-400

2-port OC-3c/STM-1c POS SPA

Note Requires SFPs.

12.2(18)SXE

SPA-4XOC3-POS

7600-SIP-200
7600-SIP-400

4-port OC-3c/STM-1c POS SPA

Note Requires SFPs.

12.2(18)SXE

SPA-1XOC12-POS

7600-SIP-400

1-port OC-12c/STM-4c POS SPA

Note Requires an SFP.

12.2(18)SXE

SPA-OC192POS-LR

7600-SIP-600

1-port OC-192c/STM-64 POS/RPR SPA, SM-LR

12.2(18)SXF

SPA-OC192POS-XFP

7600-SIP-600

1-port OC-192c/STM-64 POS/RPR SPA, XFP Optics

12.2(18)SXF

XFP Modules Supported in SPA-OC192POS-XFP

XFP-10GLR-OC192SR Single-Mode (SM) Short Reach (SR)

XFP-10GER-OC192IR Single-Mode (SM) Intermediate Reach (IR-2)

SPA-OC192POS-VSR

7600-SIP-600

1-port OC-192c/STM-64 POS/RPR SPA, VSR-1

12.2(18)SXF1


ATM SPAs

Product ID
(append "=" for spares)
SIP Support
Product Description
Minimum Software Version
SPA-2XOC3-ATM

7600-SIP-200
7600-SIP-400

2-port OC-3c/STM-1c ATM SPA

Note Requires SFPs.

12.2(18)SXE

SPA-4XOC3-ATM

7600-SIP-200
7600-SIP-400

4-port OC-3c/STM-1c ATM SPA

Note Requires SFPs.

12.2(18)SXE

SPA-1XOC12-ATM

7600-SIP-400

1-Port OC-12c/STM-4c ATM SPA

Note Requires an SFP.

12.2(18)SXE

SPA-1XOC48-ATM

7600-SIP-400

1 port OC-48c/STM-16 ATM SPA

12.2(18)SXF


SFPs for OC3 and OC12 POS and ATM SPAs

Product ID
(append "=" for spares)
Product Description
SFP-OC3-MM

OC-3/STM-1 pluggable short-reach (2 km) transceiver module, 1310-nm wavelength, MMF, LC connector

SFP-OC3-SR

OC-3/STM-1 pluggable short-reach (2 km) transceiver module, 1310-nm wavelength, LC connector

SFP-OC3-IR1

OC-3/STM-1 pluggable intermediate-reach (15 km) transceiver module, 1310-nm wavelength, LC connector

SFP-OC3-LR1

OC-3/STM-1 pluggable long-reach (40 km) transceiver module, 1310-nm wavelength, LC connector

SFP-OC3-LR2

OC-3/STM-1 pluggable long-reach (80 km) transceiver module, 1550-nm wavelength, LC connector

SFP-OC12-MM

OC-12/STM-4 pluggable short-reach (2 km) transceiver module, 1310-nm wavelength, MMF, LC connector

SFP-OC12-SR

OC-12/STM-4 pluggable short-reach (2 km) transceiver module, 1310-nm wavelength, LC connector

SFP-OC12-IR1

OC-12/STM-4 pluggable intermediate-reach (15 km) transceiver module, 1310-nm wavelength

SFP-OC12-LR1

OC-12/STM-4 pluggable long-reach (40 km) transceiver module, 1310-nm wavelength, LC connector

SFP-OC12-LR2

OC-12/STM-4 pluggable long-reach (80 km) transceiver module, 1550-nm wavelength, LC connector


Serial SPAs

Product ID
(append "=" for spares)
SIP Support
Product Description
Minimum Software Version
SPA-8XCHT1/E1

7600-SIP-200

8-Port Channelized T1/E1 SPA

12.2(18)SXE

SPA-2XT3/E3

7600-SIP-200

2-port Clear Channel T3/E3 SPA

12.2(18)SXE

SPA-4XT3/E3

7600-SIP-200

4-port Clear Channel T3/E3 SPA

12.2(18)SXE

SPA-2XCT3/DS0

7600-SIP-200

2-port Channelized T3 to DS0 SPA

12.2(18)SXE

SPA-4XCT3/DS0

7600-SIP-200

4-port Channelized T3 to DS0 SPA

12.2(18)SXE


Services SPA Carrier (SSC)

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
7600-SSC-400

5.43 A@42 V

Services SPA Carrier (SSC)

With Supervisor Engine 720

12.2(18)SXE2

With Supervisor Engine 32

12.2(18)SXF2

Note

7600-SSC-400 does not maintain state when an NSF with SSO redundancy mode switchover occurs.

7600-SSC-400 is not supported when a 7600-SIP-600 is installed.


Services SPAs


Note See the "FPD Image Packages" section for information about additional procedures required to support SPA-IPSEC-2G with Release 12.2(18)SXE and later releases.


Product ID
(append "=" for spares)
Carrier
Product Description
Minimum Software Version
SPA-IPSEC-2G

7600-SSC-400

IPsec SPA

12.2(18)SXE2

Note SPA-IPSEC-2G does not support TACACS+ authentication for IPsec. (CSCee33200)


FlexWAN and Enhanced FlexWAN Modules


NoteIn releases earlier than Release 12.2(18)SXD1, WS-SVC-WLAN-1-K9 has not been tested with the FlexWAN or Enhanced FlexWAN modules.

The following service modules have not been tested with the Enhanced FlexWAN module and Release 12.2(17b)SXA, Release 12.2(17b)SXA2, or Release 12.2(17d)SXB:

WS-X6066-SLB-APC content switching module (CSM)

WS-SVC-IDSM2-K9 intrusion detection system module

WS-SVC-NAM-2 and WS-SVC-NAM-1 network analysis modules (NAMs)

WS-SVC-SSL-1 SSL services module


Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-X6582-2PA

2.50 A@42 V

Enhanced FlexWAN Module; CEF256

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

Note See the "FPD Image Packages" section for information about additional procedures required to support WS-X6582-2PA with Release 12.2(18)SXE and later releases.

WS-X6182-2PA

2.38 A@42 V

FlexWAN Module

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 2

12.2(17d)SXB

Note

Support for WS-X6182-2PA was unintentionally disabled in Release 12.2(18)SXF7 Cisco IOS Software modularity images. (CSCsg97079)

Supervisor Engine 32 does not support WS-X6182-2PA.


FlexWAN and Enhanced FlexWAN Module Port Adapters

Product ID
(append "=" for spares)
Product Description
Minimum Software Version
PA-2FE

2-port Fast Ethernet Port Adapter (supported only in WS-X6582-2PA)

12.2(18)SXE

PA-1FE

1-port Fast Ethernet Port Adapter (supported only in WS-X6582-2PA)

12.2(18)SXE

PA-POS-1OC3

1-port Packet over SONET OC3c/STM1 Port Adapter

12.2(18)SXE

PA-POS-2OC3

2-port POS OC3c/STM1

12.2(17b)SXA

SFPs for PA-POS-2OC3
 SFP-OC3-MM

Short range, multimode fiber

12.2(17b)SXA

 SFP-OC3-IR1

Intermediate range, single-mode fiber

12.2(17b)SXA

 SFP-OC3-LR1

Long range, single-mode fiber

12.2(17b)SXA

PA-POS-OC3MM
PA-POS-OC3SMI
PA-POS-OC3SML

Packet over SONET (OC-3)

12.2(14)SX

PA-A6-OC3MM

1-port ATM OC-3c/STM-1 multimode port adapter, enhanced

12.2(14)SX

PA-A6-OC3SMI

1-port ATM OC-3c/STM-1 single-mode (IR) port adapter, enhanced

12.2(14)SX

PA-A6-OC3SML

1-port ATM OC-3c/STM-1 single-mode (LR) port adapter, enhanced

12.2(14)SX

PA-A6-T3

1-port ATM DS3 port adapter, enhanced

12.2(14)SX

PA-A6-E3

1-port ATM E3 port adapter, enhanced

12.2(14)SX

PA-A3-OC3MM
PA-A3-OC3SMI
PA-A3-T3
PA-A3-OC3SML
PA-A3-E3
PA-A3-8T1IMA
PA-A3-8E1IMA

ATM with traffic shaping

Note These port adapters do not support LANE when installed in the FlexWAN module.

12.2(14)SX

PA-T3
PA-T3+
PA-2T3
PA-2T3+
PA-E3
PA-2E3
PA-MC-T3
PA-MC-E3
PA-MC-2T3+

T3/E3 (clear-channel and channelized)

12.2(14)SX

PA-4T+
PA-8T-V35
PA-8T-X21
PA-8T-232
PA-MC-2E1/120
PA-MC-8T1
PA-MC-8E1/120
PA-MC-2T1
PA-MC-4T1

T1/E1

12.2(14)SX

PA-4E1G/75
PA-4E1G/120

T1/E1

12.2(17)SX

PA-MC-8TE1+

Multichannel T1/E1 8PRI

Note This port adapter does not support ISDN PRI when installed in the FlexWAN module.

12.2(14)SX

PA-H
PA-2H

HSSI

12.2(14)SX

PA-MC-STM-1

Multichannel STM-1

12.2(14)SX


Service Modules


NoteFor any service modules that runs its own software, see the service module software release notes for information about the minimum required service module software version.

With SPAN configured to include a port-channel interface to support a service module, be aware of CSCth03423 and CSCsx46323.


Application Control Engine (ACE) Module

Wireless Services Module (WiSM)

Application-Oriented Networking Module

WebVPN Services Module

Anomaly Guard Module

Traffic Anomaly Detector Module

Wireless LAN Service Module (WLSM)

Persistent Storage Device (PSD) Module

Multi-Processor WAN Application Module (MWAM)

Content Services Gateway (CSG) Module

Communication Media Module (CMM)

IPsec VPN Acceleration Services Module

Content Switching Module with SSL (CSM-S)

Content Switching Module (CSM)

Firewall Services Module

Intrusion Detection System Modules (IDSMs)

Network Analysis Modules (NAMs)

Secure Sockets Layer (SSL) Services Module

Application Control Engine (ACE) Module

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Versions
ACE10-6500-K9
ACE20-MOD-K9

5.23 A@42 V

Application Control Engine (ACE) module

 

With Supervisor Engine 720

12.2(18)SXF4

The ACE module runs its own software—See these publications:

http://www.cisco.com/en/US/products/ps6906/tsd_products_support_model_home.html

See the ACE software release notes for information about the minimum required ACE software version.

Note

Cisco IOS Software modularity does not support ACE10-6500-K9 or ACE20-MOD-K9.

Supervisor Engine 32 does not support ACE10-6500-K9 or ACE20-MOD-K9.

Supervisor Engine 2 does not support ACE10-6500-K9 or ACE20-MOD-K9.


Wireless Services Module (WiSM)

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Versions
WS-SVC-WISM-1-K9

6.07 A@42 V

Wireless Services Module (WiSM)

 

With Supervisor Engine 720

12.2(18)SXF2

WS-SVC-WISM-1-K9 runs its own software—See these publications:

http://www.cisco.com/en/US/products/ps6526/tsd_products_support_model_home.html

See the WS-SVC-WISM-1-K9 software release notes for information about the minimum required WS-SVC-WISM-1-K9 software version.

Note

In Release 12.2(18)SXF4, Cisco IOS Software modularity does not support WS-SVC-WISM-1-K9.

In Release 12.2(18)SXF5 and later releases, Cisco IOS Software modularity supports WS-SVC-WISM-1-K9.

Supervisor Engine 32 does not support WS-SVC-WISM-1-K9.

Supervisor Engine 2 does not support WS-SVC-WISM-1-K9.

In a 13-slot chassis, WS-SVC-WISM-1-K9 is supported only in slots 9 through 13 and does not power up in other slots.


Application-Oriented Networking Module

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Versions
WS-SVC-AON-1-K9

4.00 A@42 V

Application-Oriented Networking (AON) Module

 

With Supervisor Engine 720

12.2(18)SXE1

WS-SVC-AON-1-K9 runs its own software—See these publications:

http://www.cisco.com/en/US/products/ps6480/prod_release_notes_list.html

See the WS-SVC-AON-1-K9 software release notes for information about the minimum required WS-SVC-AON-1-K9 software version.

Note

Cisco IOS Software modularity does not support WS-SVC-AON-1-K9.

Supervisor Engine 32 does not support WS-SVC-AON-1-K9.

Supervisor Engine 2 does not support WS-SVC-AON-1-K9.


WebVPN Services Module

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Versions
WS-SVC-WEBVPN-K9

2.94 A@42 V

WebVPN Services Module

 

With Supervisor Engine 720

12.2(18)SXE2
12.2(17d)SXB7

With Supervisor Engine 32

12.2(18)SXF

WS-SVC-WEBVPN-K9 runs its own software—See these publications:

http://www.cisco.com/en/US/products/hw/switches/ps708/prod_release_notes_list.html#anchor24

See the WS-SVC-WEBVPN-K software release notes for information about the minimum required WS-SVC-WEBVPN-K software version.

Note

Cisco IOS Software modularity does not support WS-SVC-WEBVPN-K9.

Supervisor Engine 2 does not support WS-SVC-WEBVPN-K9.


Anomaly Guard Module

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-SVC-AGM-1-K9

4.00 A@42 V

Anomaly Guard Module

 

With Supervisor Engine 720

12.2(18)SXD3

With Supervisor Engine 2

12.2(18)SXD3

WS-SVC-AGM-1-K9 runs its own software—See these publications:

http://www.cisco.com/en/US/products/ps6236/tsd_products_support_model_home.html

See the WS-SVC-AGM-1-K9 software release notes for information about the minimum required WS-SVC-AGM-1-K9 software version.

Note

Cisco IOS Software modularity does not support WS-SVC-AGM-1-K9.

Supervisor Engine 32 does not support WS-SVC-AGM-1-K9.

In Release 12.2(18)SXD3 and rebuilds, WS-SVC-AGM-1-K9 has not been tested with OSMs or FlexWAN modules.


Traffic Anomaly Detector Module

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-SVC-ADM-1-K9

4.00 A@42 V

Traffic Anomaly Detector Module

 

With Supervisor Engine 720

12.2(18)SXD3

With Supervisor Engine 2

12.2(18)SXD3

WS-SVC-ADM-1-K9 runs its own software—See these publications:

http://www.cisco.com/en/US/products/ps6236/tsd_products_support_model_home.html

See the WS-SVC-ADM-1-K9 software release notes for information about the minimum required WS-SVC-ADM-1-K9 software version.

Note

Cisco IOS Software modularity does not support WS-SVC-ADM-1-K9.

Supervisor Engine 32 does not support WS-SVC-ADM-1-K9.

In Release 12.2(18)SXD3 and rebuilds, WS-SVC-ADM-1-K9 has not been tested with OSMs or FlexWAN modules.


Wireless LAN Service Module (WLSM)

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-SVC-WLAN-1-K9

3.10 A@42 V

Wireless LAN service module

 

With Supervisor Engine 720

12.2(18)SXD

WS-SVC-WLAN-1-K9 runs its own software—See these publications:

http://www.cisco.com/en/US/products/ps5865/tsd_products_support_eol_model_home.html

See the WS-SVC-WLAN-1-K9 software release notes for information about the minimum required WS-SVC-WLAN-1-K9 software version.

Note

Cisco IOS Software modularity does not support WS-SVC-WLAN-1-K9.

Supervisor Engine 32 does not support WS-SVC-WLAN-1-K9.

Supervisor Engine 2 does not support WS-SVC-WLAN-1-K9.

In releases earlier than Release 12.2(18)SXD1, WS-SVC-WLAN-1-K9 has not been tested with OSMs or FlexWAN modules.


Persistent Storage Device (PSD) Module

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-SVC-PSD-1

4.00 A@42 V

Persistent Storage Device Module

 

With Supervisor Engine 720

12.2(18)SXD1

With Supervisor Engine 32

12.2(18)SXF7

With Supervisor Engine 2

12.2(17d)SXB

WS-SVC-PSD-1 runs its own software—See these publications:

http://www.cisco.com/en/US/products/hw/switches/ps708/prod_release_notes_list.html#anchor21

See the WS-SVC-PSD-1 software release notes for information about the minimum required WS-SVC-PSD-1 software version.

Note

Cisco IOS Software modularity does not support WS-SVC-PSD-1.

With Release 12.2(18)SXD1 and later, WS-SVC-PSD-1 maintains state when an NSF with SSO redundancy mode switchover occurs.


Multi-Processor WAN Application Module (MWAM)

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-SVC-MWAM-1

3.57 A@42 V

Multi-Processor WAN Application Module

 

With Supervisor Engine 720

12.2(18)SXD1

With Supervisor Engine 32

12.2(18)SXF5

With Supervisor Engine 2

12.2(17d)SXB

WS-SVC-MWAM-1 runs its own software—See these publications:

http://www.cisco.com/en/US/docs/wireless/pdsn/12.28zb/mwan_install_config/mwamhwrn.html

See the WS-SVC-MWAM-1 software release notes for information about the minimum required WS-SVC-MWAM-1 software version.

Note

Cisco IOS Software modularity does not support WS-SVC-MWAM-1.

With Release 12.2(18)SXD1 and later releases, WS-SVC-MWAM-1 maintains state when an NSF with SSO redundancy mode switchover occurs.

With Releases earlier than Release 12.2(18)SXD1, WS-SVC-MWAM-1 does not maintain state when an NSF with SSO redundancy mode switchover occurs.


Content Services Gateway (CSG) Module

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-SVC-CSG-1

3.00 A@42 V

Content Services Gateway (CSG) Module

 

With Supervisor Engine 720

12.2(18)SXD1

With Supervisor Engine 2

12.2(17d)SXB

WS-SVC-CSG-1 runs its own software—See these publications:

http://www.cisco.com/en/US/products/sw/wirelssw/ps779/tsd_products_support_series_home.html

See the WS-SVC-CSG-1 software release notes for information about the minimum required WS-SVC-CSG-1 software version.

Note

Cisco IOS Software modularity does not support WS-SVC-CSG-1.

Supervisor Engine 32 does not support WS-SVC-CSG-1.


Communication Media Module (CMM)

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-SVC-CMM

6.00 A@42 V

Communication Media Module

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-SVC-CMM runs its own software—See these publications:

http://www.cisco.com/en/US/docs/interfaces_modules/services_modules/cmm/release/notes/OL_4847.html

See the WS-SVC-CMM software release notes for information about the minimum required WS-SVC-CMM software version.

Note Cisco IOS Software modularity does not support WS-SVC-CMM.

Communication Media Module Port Adapters
 WS-SVC-CMM-6E1

6-Port E1 Interface Port Adapter

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 2

12.2(17d)SXB

 WS-SVC-CMM-6T1

6-Port T1 Interface Port Adapter

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 2

12.2(17d)SXB

 WS-SVC-CMM-ACT

Adhoc Conferencing and Transcoding Port Adapter

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 2

12.2(17d)SXB

 WS-SVC-CMM-24FXS

24-Port FXS Interface Port Adapter

 

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 2

12.2(17d)SXB


IPsec VPN Acceleration Services Module

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-SVC-IPSEC-1

1.89 A@42 V

IPsec VPN Acceleration Services Module

 

With Supervisor Engine 720

12.2(17b)SXA

With Supervisor Engine 2

12.2(17d)SXB

WS-SVC-IPSEC-1 uses the Cisco IOS software that is running on the switch.

Note

Cisco IOS Software modularity does not support WS-SVC-IPSEC-1.

Supervisor Engine 32 does not support WS-SVC-IPSEC-1.

With Release 12.2(18)SXE and later releases, WS-SVC-IPSEC-1 requires an advanced services image (see the "Feature Sets" section).

With releases earlier than Release 12.2(18)SXE, WS-SVC-IPSEC-1 requires a k9 image (see the "Feature Sets" section).

WS-SVC-IPSEC-1 does not support TACACS+ authentication for IPsec. (CSCee33200)

WS-SVC-IPSEC-1 does not maintain state when an NSF with SSO redundancy mode switchover occurs.

WS-SVC-IPSEC-1 does not maintain state when a single router mode with stateful switchover (SRM with SSO) redundancy mode switchover occurs.

In releases earlier than Release 12.2(18)SXD1, WS-SVC-IPSEC-1 has not been tested with OSM-1CHOC12/T1-SI or OSM-12CT3/T1.

To avoid reloads with software releases where caveat CSCed17605 is not resolved (CSCed17605 is resolved in Release 12.2(17d)SXB and later releases), do not configure the single router mode with stateful switchover (SRM with SSO) redundancy mode with a WS-SVC-IPSEC-1 module installed. In software releases where caveat CSCed17605 is not resolved, the WS-SVC-IPSEC-1 module does not maintain state when an SRM with SSO redundancy mode switchover occurs.


Content Switching Module with SSL (CSM-S)

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-X6066-SLB-S-K9

2.15 A@42 V

Content Switching Module with SSL (CSM-S)

 

With Supervisor Engine 720

12.2(18)SXE

With Supervisor Engine 2

12.2(18)SXD

WS-X6066-SLB-S-K9 runs its own software—See these publications:

http://www.cisco.com/en/US/products/hw/modules/ps2706/ps780/tsd_products_support_model_home.html

See the WS-X6066-SLB-S-K9 software release notes for information about the minimum required WS-X6066-SLB-S-K9 software version.

Note

Cisco IOS Software modularity does not support WS-X6066-SLB-S-K9.

Supervisor Engine 32 does not support WS-X6066-SLB-S-K9.

With Release 12.2(18)SXD1 and later releases, WS-X6066-SLB-S-K9 maintains state when an NSF with SSO redundancy mode switchover occurs.

WS-X6066-SLB-S-K9 does not maintain state when a single router mode with stateful switchover (SRM with SSO) redundancy mode switchover occurs.

The OSM-2+4GE-WAN+ and the OC-12 Packet-over-SONET OSMs have been tested with the WS-X6066-SLB-S-K9 content switching module.

In releases earlier than Release 12.2(18)SXD1, the WS-X6066-SLB-S-K9 content switching module has not been tested with other OSMs or the Enhanced FlexWAN module.


Content Switching Module (CSM)

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-X6066-SLB-APC

3.00 A@42 V

Content Switching Module

 

With Supervisor Engine 720

12.2(14)SX1

With Supervisor Engine 2

12.2(17d)SXB

WS-X6066-SLB-APC runs its own software—See these publications:

http://www.cisco.com/en/US/products/hw/modules/ps2706/ps780/tsd_products_support_model_home.html

See the WS-X6066-SLB-APC software release notes for information about the minimum required WS-X6066-SLB-APC software version.

Note

Supervisor Engine 32 does not support WS-X6066-SLB-APC.

With Release 12.2(18)SXD1 and later releases, WS-X6066-SLB-APC maintains state when an NSF with SSO redundancy mode switchover occurs.

WS-X6066-SLB-APC does not maintain state when a single router mode with stateful switchover (SRM with SSO) redundancy mode switchover occurs.

The OSM-2+4GE-WAN+ and the OC-12 Packet-over-SONET OSMs have been tested with the WS-X6066-SLB-APC content switching module and WS-SUP720.

In releases earlier than Release 12.2(18)SXD1, WS-X6066-SLB-APC has not been tested with other OSMs or the Enhanced FlexWAN module.


Firewall Services Module

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-SVC-FWM-1-K9

4.09 A@42 V

Firewall Services Module; CEF256

 

With Supervisor Engine 720

12.2(14)SX1

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-SVC-FWM-1-K9 runs its own software—See these publications:

http://www.cisco.com/en/US/products/hw/modules/ps2706/ps4452/tsd_products_support_model_home.html

See the WS-SVC-FWM-1-K9 software release notes for information about the minimum required WS-SVC-FWM-1-K9 software version.

Note

With Release 12.2(18)SXD3 and later Cisco IOS releases and with Firewall Services Module Software Release 2.3(1), WS-SVC-FWM-1-K9 maintains state when an NSF with SSO redundancy mode switchover occurs.

WS-SVC-FWM-1-K9 does not maintain state when a single router mode with stateful switchover (SRM with SSO) redundancy mode switchover occurs.


Intrusion Detection System Modules (IDSMs)

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-SVC-IDSM2-K9

2.50 A@42 V

Intrusion Detection System Module 2; CEF256

 

With Supervisor Engine 720

12.2(14)SX1

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-SVC-IDSM2-K9 runs its own software—See these publications:

http://www.cisco.com/en/US/products/hw/modules/ps2706/ps5058/tsd_products_support_model_home.html

See the WS-SVC-IDSM2-K9 software release notes for information about the minimum required WS-SVC-IDSM2-K9 software version.

Note

WS-SVC-IDSM2-K9 has been tested with OSM-2+4GE-WAN+ and the OC-12 Packet-over-SONET OSMs.

In releases earlier than Release 12.2(18)SXD1, WS-SVC-IDSM2-K9 has not been tested with other OSMs or the Enhanced FlexWAN module.


Network Analysis Modules (NAMs)

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-SVC-NAM-2

3.47 A@42 V

Network Analysis Module 2; CEF256

WS-SVC-NAM-1

2.89 A@42 V

Network Analysis Module 1; CEF256

 

With Supervisor Engine 720

12.2(14)SX1

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-SVC-NAM-2 and WS-SVC-NAM-1 run their own software—See this publication for more information:

http://www.cisco.com/en/US/products/hw/modules/ps2706/ps5025/tsd_products_support_model_home.html

See the WS-SVC-NAM-2 and WS-SVC-NAM-1 software release notes for information about the minimum required WS-SVC-NAM-2 and WS-SVC-NAM-1 software version.

Note

With Release 12.2(17b)SXA and rebuilds and Release 12.2(17d)SXB and rebuilds, WS-SVC-NAM-2 and WS-SVC-NAM-1 support single router mode with stateful switchover (SRM with SSO) redundancy mode.

WS-SVC-NAM-2 and WS-SVC-NAM-1 have been tested with OSM-2+4GE-WAN+ and the OC-12 Packet-over-SONET OSMs.

In releases earlier than Release 12.2(18)SXD1, WS-SVC-NAM-2 and WS-SVC-NAM-1 have not been tested with other OSMs or the Enhanced FlexWAN module.


Secure Sockets Layer (SSL) Services Module

Product ID
(append "=" for spares)
Power
Required
Product Description
Minimum Software Version
WS-SVC-SSL-1

2.94 A@42 V

Secure Sockets Layer (SSL) Services Module

 

With Supervisor Engine 720

12.2(14)SX1

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

Note  

Cisco IOS Software modularity does not support WS-SVC-SSL-1.

WS-SVC-SSL-1 does not maintain state when an NSF with SSO redundancy mode switchover occurs.

WS-SVC-SSL-1 does not maintain state when a single router mode with stateful switchover (SRM with SSO) redundancy mode switchover occurs.

WS-SVC-SSL-1 has been tested with OSM-2+4GE-WAN+ and the OC-12 Packet-over-SONET OSMs.

In releases earlier than Release 12.2(18)SXD1, WS-SVC-SSL-1 has not been tested with other OSMs or the Enhanced FlexWAN module.


Fan Trays

High-Capacity Fan Trays

Standard-Capacity Fan Trays


NoteEnter the show environment status | include fan command or the show environment cooling command to display information about the installed fan trays.

To use a high-capacity fan tray with a Supervisor Engine 2, you must enter the hw-module fan-tray version 2 command and then remove and quickly reinsert the fan tray.


High-Capacity Fan Trays

These high-capacity fan trays support both all supervisor engines and require at least a 2,500 W power supply.

Product ID
(append "=" for spares)
Power
Allocated at 42 V
Product Description
Minimum
Software
Version
WS-C6503-E-FAN

1.37 A@42 V

High-capacity fan tray for WS-C6503-E chassis

12.2(14)SX

Note In releases earlier than Release 12.2(18)SXD, WS-C6503-E-FAN requires the same power as FAN-MOD-3HS.

FAN-MOD-3HS

2.98 A@42 V

High-capacity fan tray for WS-C6503 and CISCO7603 chassis

12.2(14)SX

FAN-MOD-6HS

4.29 A@42 V

High-capacity fan tray for CISCO7606 chassis

12.2(14)SX

WS-C6506-E-FAN

2.35 A@42 V

High-capacity fan tray for WS-C6506-E chassis

12.2(14)SX

WS-C6K-6SLOT-FAN2

12 V fan

High-capacity fan tray for WS-C6506 chassis

12.2(14)SX

FAN-MOD-09

5.75 A@42 V

High-capacity fan tray for WS-C6509-NEB-A and CISCO7609 chassis

12.2(14)SX

WS-C6509-V-E-FAN

5.75 A@42 V

High-capacity fan tray for WS-C6509-V-E chassis

12.2(18)SXF10

WS-C6509-E-FAN

3.58 A@42 V

High-capacity fan tray for WS-C6509-E chassis

12.2(14)SX

WS-C6K-9SLOT-FAN2

12 V fan

High-capacity fan tray for WS-C6509 chassis

12.2(14)SX

WS-C6K-13SLT-FAN2

7.10 A@42 V

High-capacity fan tray for WS-C6513 and CISCO7613 chassis

12.2(14)SX


Standard-Capacity Fan Trays

These standard-capacity fan trays support only Supervisor Engine 2.

Product ID
(append "=" for spares)
Power
Allocated at 42 V
Product Description
Minimum
Software
Version
FAN-MOD-3

None

Standard-capacity fan tray for WS-C6503 and CISCO7603 chassis

12.2(17d)SXB

FAN-MOD-6

None

Standard-capacity fan tray for CISCO7606 chassis

12.2(17d)SXB

WS-C6K-6SLOT-FAN

12 V fan

Standard-capacity fan tray for WS-C6506 chassis

12.2(17d)SXB

WS-C6509-NEB-FAN

12 V fan

Standard fan tray for WS-C6509-NEB chassis

12.2(17d)SXB

WS-C6K-9SLOT-FAN

12 V fan

Standard-capacity fan tray for WS-C6509 chassis

12.2(17d)SXB

WS-C6K-13SLT-FAN

12 V fan

Standard-capacity fan tray for WS-C6513 and CISCO7613 chassis

12.2(17d)SXB


Power Supplies

CISCO7606 Power Supplies

WS-C6504-E and CISCO7604 Power Supplies

WS-C6503, WS-C6503-E, and CISCO7603 Power Supplies

All Other Power Supplies

CISCO7606 Power Supplies

Product ID
(append "=" for spares)
Product Description
Minimum Software Version
PWR-2700-AC

2700 W AC power supply

12.2(18)SXE

PWR-2700-DC

2700 W DC power supply

12.2(18)SXE


WS-C6504-E and CISCO7604 Power Supplies

Product ID
(append "=" for spares)
Product Description
Minimum Software Version
PWR-2700-AC/4

2700 W AC power supply

12.2(18)SXE

PWR-2700-DC/4

2700 W DC power supply

12.2(18)SXE


WS-C6503, WS-C6503-E, and CISCO7603 Power Supplies

Product ID
(append "=" for spares)
Product Description
Minimum Software Version
PWR-1400-AC

1,400 W AC power supply

12.2(17a)SX

PWR-950-AC

950 W AC power supply

12.2(14)SX

PWR-950-DC

950 W DC power supply

12.2(14)SX


All Other Power Supplies


Note The power supplies in this section are not supported in these chassis:

Catalyst 6503

Catalyst 6503-E

CISCO7603

Catalyst 6504-E

CISCO7604


Product ID
(append "=" for spares)
Product Description
Minimum Software Version
WS-CAC-8700W-E

8,700 W AC power supply

12.2(18)SXF8

Note

Limited to 6,000 W in the WS-C6513 and CISCO7613 chassis.

Limited to 4,500 W in the WS-C6509-NEB-A chassis.

Limited to 4,000 W in these chassis:

WS-C6509

WS-C6506

WS-C6509-NEB

WS-CAC-8700W-E supports a remote power cycling feature.

See this publication for more information:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Chassis_Installation/Cat6500/6500_ins.html

PWR-6000-DC

6,000 W DC power supply

12.2(18)SXF13

Note

Limited to 4,500 W in the WS-C6509-NEB-A chassis.

Limited to 4,000 W in these chassis:

WS-C6509

WS-C6506

WS-C6509-NEB

WS-CAC-6000W

6,000 W AC power supply

12.2(18)SXD

Note

Limited to 4,500 W in the WS-C6509-NEB-A chassis.

Limited to 4,000 W in these chassis:

WS-C6509

WS-C6506

WS-C6509-NEB

With releases earlier than Release 12.2(18)SXD, limited to 4,000 W in the WS-C6506-E and WS-C6509-E chassis.

PWR-4000-DC

4,000 W DC power supply

12.2(14)SX

WS-CAC-4000W

4,000 W AC power supply

12.2(14)SX

+WS-CAC-3000W

3,000 W AC power supply

12.2(17a)SX

Note

Required with Supervisor Engine 720 in WS-C6509-NEB or OSR7609 chassis.

Included in the WS-6509-NEB-UPGRD= upgrade kit.

WS-CAC-3000W

3,000 W AC power supply

12.2(14)SX

WS-CAC-2500W

2,500 W AC power supply

12.2(14)SX

WS-CDC-2500W

2,500 W DC power supply

12.2(14)SX


Chassis

13-Slot Chassis

9-Slot Chassis

6-Slot Chassis

4-Slot Chassis

3-Slot Chassis

13-Slot Chassis

Product ID
(append "=" for spare)
Product Description
Minimum Software Version
WS-C6513-E

Catalyst 6513-E chassis:

13 slots

64 chassis MAC addresses

Does not support these modules:

Supervisor Engine 2

WS-C6500-SFM

These modules are supported only in slots 9 through 13 and do not power up in other slots:

WS-X6700 series switching modules except WS-X6724-SFP

WS-X6816-GBIC switching modules

WS-SVC-WISM-1-K9

With Supervisor Engine 720

12.2(18)SXF14

With Supervisor Engine 32

12.2(18)SXF14

WS-C6513

Catalyst 6513 chassis:

13 slots

64 chassis MAC addresses

Use with Supervisor Engine 720 requires WS-C6K-13SLT-FAN2

Does not support WS-C6500-SFM

These modules are supported only in slots 9 through 13 and do not power up in other slots:

WS-X6708-10GE

WS-X6704-10GE

WS-X6748-SFP

WS-X6748-GE-TX

WS-X6816-GBIC

WS-SVC-WISM-1-K9

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

CISCO7613

Cisco 7613 chassis:

13 slots

64 chassis MAC addresses

Use with Supervisor Engine 720 requires WS-C6K-13SLT-FAN2

Does not support WS-C6500-SFM

These modules are supported only in slots 9 through 13 and do not power up in other slots:

WS-X6708-10GE

WS-X6704-10GE

WS-X6748-SFP

WS-X6816-GBIC

WS-X6748-GE-TX

WS-SVC-WISM-1-K9

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB


9-Slot Chassis

Product ID
(append "=" for spare)
Product Description
Minimum Software Version
WS-C6509-V-E

Catalyst 6509-V-E chassis:

9 vertical slots

64 chassis MAC addresses

Requires WS-C6509-V-E-FAN

Required power supply:

2,500 W DC or higher

3,000 W AC or higher

Supervisor Engine 2 is not supported in WS-C6509-V-E.

With Supervisor Engine 720

12.2(18)SXF10

With Supervisor Engine 32

12.2(18)SXF10

WS-C6509-E

Catalyst 6509-E chassis:

9 horizontal slots

Chassis MAC addresses:

Before April 2009—1024 chassis MAC addresses

Starting in April 2009—64 chassis MAC addresses

Note Chassis with 64 MAC addresses automatically enable the Extended System ID feature, which is enabled with the spanning-tree extend system-id command. You cannot disable the extended-system ID in chassis that support 64 MAC addresses. The Extended System ID feature might already be enabled in your network, because it is required to support both extended-range VLANs and any chassis with 64 MAC addresses. Enabling the extended system ID feature for the first time updates the bridge IDs of all active STP instances, which might change the spanning tree topology.

Requires WS-C6509-E-FAN

Requires 2,500 W or higher power supply

With releases earlier than Release 12.2(18)SXD, WS-CAC-6000W is limited to 4,000 W in WS-C6509-E

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-C6509

Catalyst 6509 chassis:

9 horizontal slots

1024 chassis MAC addresses

Use with Supervisor Engine 720 or Supervisor Engine 32 requires WS-C6K-9SLOT-FAN2

WS-CAC-6000W is limited to 4,000 W in WS-C6509

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-C6509-NEB-A

Catalyst 6509-NEB chassis

9 vertical slots

64 chassis MAC addresses

No fan tray upgrade required for use with Supervisor Engine 720

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-C6509-NEB

Catalyst 6509-NEB chassis:

9 vertical slots

1024 chassis MAC addresses

Use with Supervisor Engine 720 or Supervisor Engine 32 requires the WS-6509-NEB-UPGRD= upgrade kit—refer to this publication:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_16162.html

With Supervisor Engine 720

12.2(17a)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

CISCO7609

Cisco 7609 chassis

9 vertical slots

64 chassis MAC addresses

No fan tray upgrade required for use with Supervisor Engine 720

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

OSR-7609

Cisco 7609 chassis:

9 vertical slots

1024 chassis MAC addresses

Use with Supervisor Engine 720 or Supervisor Engine 32 requires the WS-6509-NEB-UPGRD= upgrade kit—refer to this publication:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/hardware/Config_Notes/78_16162.html

With Supervisor Engine 720

12.2(17a)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB


6-Slot Chassis

Product ID
(append "=" for spare)
Product Description
Minimum Software Version
WS-C6506-E

Catalyst 6506-E chassis:

6 slots

Chassis MAC addresses:

Before April 2009—1024 chassis MAC addresses

Starting in April 2009—64 chassis MAC addresses

Note Chassis with 64 MAC addresses automatically enable the Extended System ID feature, which is enabled with the spanning-tree extend system-id command. You cannot disable the extended-system ID in chassis that support 64 MAC addresses. The Extended System ID feature might already be enabled in your network, because it is required to support both extended-range VLANs and any chassis with 64 MAC addresses. Enabling the extended system ID feature for the first time updates the bridge IDs of all active STP instances, which might change the spanning tree topology.

Requires WS-C6506-E-FAN

Requires 2,500 W or higher power supply

With releases earlier than Release 12.2(18)SXD, WS-CAC-6000W is limited to 4,000 W in WS-C6506-E

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-C6506

Catalyst 6506 chassis:

6 slots

1024 chassis MAC addresses

Use with Supervisor Engine 720 or Supervisor Engine 32 requires WS-C6K-6SLOT-FAN2

WS-CAC-6000W limited to 4,000 W in WS-C6506

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

CISCO7606

Cisco 7606 chassis:

6 slots

64 chassis MAC addresses

Use with Supervisor Engine 720 or Supervisor Engine 32 requires FAN-MOD-6HS

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB


4-Slot Chassis

Product ID
(append "=" for spare)
Product Description
Minimum Software Version
WS-C6504-E

Catalyst 6504-E chassis:

4 slots

64 chassis MAC addresses

Does not support:

Supervisor Engine 2

WS-X6500-SFM2

WS-C6500-SFM

WS-F6K-DFC

With Supervisor Engine 720

12.2(18)SXE

With Supervisor Engine 32

12.2(18)SXF

CISCO7604

Cisco 7604 chassis:

4 slots

64 chassis MAC addresses

Does not support:

Supervisor Engine 2

WS-X6500-SFM2

WS-C6500-SFM

WS-F6K-DFC

With Supervisor Engine 720:

12.2(18)SXE

With Supervisor Engine 32

12.2(18)SXF


3-Slot Chassis

Product ID
(append "=" for spare)
Product Description
Minimum Software Version
WS-C6503-E

3 slots

64 chassis MAC addresses

Use with Supervisor Engine 720 requires WS-C6503-E-FAN

With Release 12.2(18)SXD and later releases, WS-C6503-E supports:

WS-X6704-10GE

WS-X6748-SFP

WS-X6724-SFP

WS-X6748-GE-TX

With releases earlier than Release 12.2(18)SXD, WS-C6503-E has the same support restrictions as WS-C6503.

WS-C6503-E does not support:

WS-X6500-SFM2

WS-C6500-SFM

WS-F6K-DFC

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

WS-C6503

Catalyst 6503 chassis:

3 slots

64 chassis MAC addresses

Use with Supervisor Engine 720 or Supervisor Engine 32 requires FAN-MOD-3HS

Does not support:

WS-X6708-10GE

WS-X6704-10GE

WS-X6748-SFP

WS-X6724-SFP

WS-X6748-GE-TX

WS-X6500-SFM2

WS-C6500-SFM

WS-F6K-DFC

With Supervisor Engine 720

12.2(14)SX

With Supervisor Engine 32

12.2(18)SXF

With Supervisor Engine 2

12.2(17d)SXB

CISCO7603

Cisco 7603 chassis:

3 slots

64 chassis MAC addresses

Use with Supervisor Engine 720 requires FAN-MOD-3HS

Does not support:

WS-X6708-10GE

WS-X6704-10GE

WS-X6748-SFP

WS-X6724-SFP

WS-X6748-GE-TX

WS-X6500-SFM2

WS-C6500-SFM

WS-F6K-DFC

With Supervisor Engine 720:

12.2(14)SX

With Supervisor Engine 2

12.2(17d)SXB

Note Supervisor Engine 32 is not supported in CISCO7603.


Unsupported Hardware

The following hardware is not supported:

DWDM-SFP-5817—1000BASE-DWDM 1558.17 nm SFP (100-GHz ITU grid) SFP module

DWDM-SFP-4692—1000BASE-DWDM 1546.92 nm SFP (100-GHz ITU grid) SFP module

See the "Supervisor Engine 32 (CAT6000-SUP32/MSFC2A, 7600-SUP32/MSFC2A)" section for information about hardware that is not supported with the Supervisor Engine 32.

With a Supervisor Engine 720, WS-X6516-GBIC hardware revisions 5.0 through 5.4 with a DFC3 installed.

Supervisor Engine 720 supports a DFC3 on these WS-X6516-GBIC hardware revisions:

Lower than 5.0

5.5 and higher

With a Supervisor Engine 720 and a DFC3 installed, WS-X6516-GBIC hardware revisions 5.0 through 5.3 do not power up. Without a DFC3, WS-X6516-GBIC hardware revisions 5.0 through 5.4 operate in bus mode.

See external field notice 24494 for more information:

http://www.cisco.com/en/US/ts/fn/200/fn24494.html

These service modules:

WS-X6381-IDS Intrusion Detection System (IDS) Module

WS-X6380-NAM Network Analysis Module (NAM)

Supervisor Engine 1 (WS-X6K-S1A-MSFC2, WS-X6K-SUP1A-MSFC)

WS-X6624-FXS, WS-X6608-T1, and WS-X6608-E1 voice modules

WS-X6101-OC12-MMF and WS-X6101-OC12-SMF ATM LANE modules

WS-X6302-MSM Multilayer Switch Module

Catalyst 6000 series chassis

These power supplies cannot support high-capacity fan trays:

WS-CAC-1300W

WS-CDC-1300W

WS-CAC-1000W

Unsupported modules remain powered down if detected and do not affect system behavior.