Catalyst 4500 Series Switch Cisco IOS Command Reference, 12.2(25)SG
aaa accounting dot1x default start-stop group radius through instance
Downloads: This chapterpdf (PDF - 0.96MB) The complete bookPDF (PDF - 5.37MB) | Feedback

Cisco IOS Commands for the Catalyst 4500 Series Switches

Table Of Contents

Cisco IOS Commands for the Catalyst 4500 Series Switches

#macro keywords

aaa accounting dot1x default start-stop group radius

aaa accounting system default start-stop group radius

access-group mode

access-list hardware entries

action

apply

arp access-list

attach module

auto qos voip

auto-sync

channel-group

channel-protocol

class-map

clear counters

clear hw-module slot password

clear interface gigabitethernet

clear interface vlan

clear ip access-template

clear ip arp inspection log

clear ip arp inspection statistics

clear ip dhcp snooping database

clear ip dhcp snooping database statistics

clear ip igmp group

clear ip igmp snooping membership

clear ip mfib counters

clear ip mfib fastdrop

clear lacp counters

clear mac-address-table dynamic

clear pagp

clear port-security

clear qos

clear vlan counters

clear vmps statistics

debug adjacency

debug backup

debug condition interface

debug condition standby

debug condition vlan

debug dot1x

debug etherchnl

debug interface

debug ipc

debug ip dhcp snooping event

debug ip dhcp snooping packet

debug ip verify source packet

debug lacp

debug monitor

debug nvram

debug pagp

debug platform packet protocol lacp

debug platform packet protocol pagp

debug pm

debug psecure

debug redundancy

debug smf updates

debug spanning-tree

debug spanning-tree backbonefast

debug spanning-tree switch

debug spanning-tree uplinkfast

debug sw-vlan

debug sw-vlan ifs

debug sw-vlan notification

debug sw-vlan vtp

debug udld

debug vqpc

define interface-range

deny

diagnostic monitor action

diagnostic start

dot1x auth-fail max-attempts

dot1x auth-fail vlan

dot1x guest-vlan

dot1x guest-vlan supplicant

dot1x host-mode

dot1x initialize

dot1x max-reauth-req

dot1x max-req

dot1x port-control

dot1x re-authenticate

dot1x re-authentication

dot1x system-auth-control

dot1x timeout

duplex

erase

errdisable detect

errdisable recovery

flowcontrol

hw-module power

hw-module uplink select

instance


Cisco IOS Commands for the Catalyst 4500 Series Switches


This chapter contains an alphabetical listing of Cisco IOS commands for the Catalyst 4500 series switches. For information about Cisco IOS commands that are not included in this publication, refer to Cisco IOS Release 12.2 Configuration Guides and Command References at this URL:

http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_product_indices_list.html

#macro keywords

To specify the help string for the macro keywords, use the #macro keywords command.

#macro keywords [keyword1] [keyword2] [keyword3]

Syntax Description

keyword 1

(Optional) Specifies a keyword that is needed while applying a macro to an interface.

keyword 2

(Optional) Specifies a keyword that is needed while applying a macro to an interface.

keyword 3

(Optional) Specifies a keyword that is needed while applying a macro to an interface.


Defaults

This command has no default settings.

Command Modes

Global configuration

Command History

Release
Modification

12.2(18)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

If you do not specify the mandatory keywords for a macro, the macro is to be considered invalid and fails when you attempt to apply it. By enteringthe #macro keywords command, you will receive a message indicating what you need to include to make the syntax valid.

Examples

This example shows how to specify the help string for keywords associated with a macro named test:

Switch(config)# macro name test
macro name test
Enter macro commands one per line. End with the character '@'.
#macro keywords $VLAN $MAX
swichport
@

Switch(config)# int gi1/1
Switch(config-if)# macro apply test ?
  WORD  Keyword to replace with a value e.g $VLAN, $MAX   << It is shown as help
  <cr>

Related Commands

macro apply cisco-desktop
macro apply cisco-phone
macro apply cisco-router
macro apply cisco-switch

aaa accounting dot1x default start-stop group radius

To enable accounting for 802.1X authentication sessions, use the aaa accounting dot1x default start-stop group radius command. To disable accounting, use the no form of this command.

aaa accounting dot1x default start-stop group radius

no aaa accounting dot1x default start-stop group radius

Syntax Description

This command has no arguments or keywords.

Defaults

Accounting is disabled.

Command Modes

Global configuration

Command History

Release
Modification

12.2(18)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

802.1X accounting requires a RADIUS server.

This command enables the Authentication, Authorization, and Accounting (AAA) client's accounting feature to forward 802.1X update and watchdog packets from the 802.1X supplicant (workstation client) to the authentication (RADIUS) server. (Watchdog packets are defined as EAPOL-LOGON, EAPOL-LOGOFF, and EAPOL-INTERIM messages.) Successful authentication and authorization of the supplicant by the authentication server is required before these packets are considered valid and are forwarded. When the client is reauthenticated, an interim-update accounting notice is sent to the accounting server.

Examples

This example shows how to configure 802.1X accounting:

Switch(config)# aaa accounting dot1x default start-stop group radius

Note The RADIUS authentication server must be properly configured to accept and log update or watchdog packets from the AAA client.


Related Commands

aaa accounting system default start-stop group radius

aaa accounting system default start-stop group radius

To receive the session termination messages after the switch reboots, use the aaa accounting system default start-stop group radius command. To disable accounting, use the no form of this command.

aaa accounting system default start-stop group radius

no aaa accounting system default start-stop group radius

Syntax Description

This command has no arguments or keywords.

Defaults

Accounting is disabled.

Command Modes

Global configuration mode

Command History

Release
Modification

12.2(18)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

802.1X accounting requires the RADIUS server.

This command enables the AAA client's accounting feature to forward 802.1X update and watchdog packets from the 802.1X supplicant (workstation client) to the authentication (RADIUS) server. (Watchdog packets are defined as EAPOL-LOGON, EAPOL-LOGOFF, and EAPOL-INTERIM messages.) Successful authentication and authorization of the supplicant by the authentication server is required before these packets are considered valid and are forwarded. When the client is reauthenticated, an interim-update accounting notice is sent to the accounting server.

Examples

This example shows how to generate a logoff after a switch reboots:

Switch(config)# aaa accounting system default start-stop group radius

Note The RADIUS authentication server must be properly configured to accept and log update or watchdog packets from the AAA client.


Related Commands

aaa accounting dot1x default start-stop group radius

access-group mode

To specify the override modes (for example, VACL overrides PACL) and the non-override modes (for example, merge or strict mode), use the access-group mode command. To return to preferred port mode, use the no form of this command.

access-group mode {prefer {port | vlan} | merge}

no access-group mode {prefer {port | vlan} | merge}

Syntax Description

prefer port

Specifies that the PACL mode take precedence if PACLs are configured. If no PACL features are configured on the port, other features applicable to the interface are merged and applied on the interface.

prefer vlan

Specifies that the VLAN-based ACL mode take precedence. If no VLAN-based ACL features are configured on the port's VLAN, the PACL features on the port are applied.

merge

Merges applicable ACL features before they are programmed into the hardware.


Defaults

PACL override mode

Command Modes

Interface configuration

Command History

Release
Modification

12.1(19)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

On the Layer 2 interface, prefer port, prefer VLAN, and merge modes are supported. A Layer 2 interface can have one IP ACL applied in either direction (one inbound and one outbound).

Examples

This example shows how to make the PACL mode on the switch take effect:

(config-if)# access-group mode prefer port

This example shows how to merge applicable ACL features:

(config-if)# access-group mode merge

Related Commands

show access-group mode interface
show ip interface
(refer to Cisco IOS documentation)
show mac access-group interface

access-list hardware entries

To designate how ACLs are programmed into the switch hardware, use the access-list hardware entries command.

access-list hardware entries {packed | scattered}

Syntax Description

packed

Directs the software to use the first entry with a matching mask when selecting an entry from the ACL TCAM for programming the ACEs in an ACL.

scattered

Directs the software to use the first entry with a free mask when selecting an entry from the ACL TCAM for programming the ACEs in an ACL.


Defaults

The ACLs are programmed as packed.

Command Modes

Global configuration

Command History

Release
Modification

12.2(20)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

Two types of hardware resources are used when ACLs are programmed: entries and masks. If one of these resources is consumed, no additional ACLs can be programmed into the hardware. If the masks are consumed, but the entries are available, change the programming algorithm from packed to scattered to make the masks available. This action allows additional ACLs to be programmed into the hardware.

The goal is to use TCAM resources more efficiently; that is, to minimize the number of masks per ACL entries. To compare TCAM utilization when using the scattered or packed algorithms, use the
show platform hardware acl statistics utilization brief command. To change the algorithm from packed to scattered, use the access-list hardware entries command.

Examples

This example shows how to program ACLs into the hardware as packed. After they are programmed, you will need 89 percent of the masks to program only 49 percent of the ACL entries.

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# access-list hardware entries packed
Switch(config)# end
Switch#
01:15:34: %SYS-5-CONFIG_I: Configured from console by console
Switch#
Switch# show platform hardware acl statistics utilization brief
Entries/Total(%)  Masks/Total(%)
                                       -----------------  ---------------
            Input  Acl(PortAndVlan)  2016 / 4096 ( 49)   460 /  512 ( 89)
            Input  Acl(PortOrVlan)      6 / 4096 (  0)     4 /  512 (  0)
            Input  Qos(PortAndVlan)     0 / 4096 (  0)     0 /  512 (  0)
            Input  Qos(PortOrVlan)      0 / 4096 (  0)     0 /  512 (  0)
            Output Acl(PortAndVlan)     0 / 4096 (  0)     0 /  512 (  0)
            Output Acl(PortOrVlan)      0 / 4096 (  0)     0 /  512 (  0)
            Output Qos(PortAndVlan)     0 / 4096 (  0)     0 /  512 (  0)
            Output Qos(PortOrVlan)      0 / 4096 (  0)     0 /  512 (  0)

            L4Ops: used 2 out of 64
Switch# 

This example shows how to reserve space (scatter) between ACL entries in the hardware. The 
number of masks required to program 49 percent of the entries has decreased to 49 percent.

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# access-list hardware entries scattered
Switch(config)# end
Switch#
01:39:37: %SYS-5-CONFIG_I: Configured from console by console
Switch#
Switch# show platform hardware acl statistics utilization brief
Entries/Total(%)  Masks/Total(%)
                                       -----------------  ---------------
            Input  Acl(PortAndVlan)  2016 / 4096 ( 49)   252 /  512 ( 49)
            Input  Acl(PortOrVlan)      6 / 4096 (  0)     5 /  512 (  0)
            Input  Qos(PortAndVlan)     0 / 4096 (  0)     0 /  512 (  0)
            Input  Qos(PortOrVlan)      0 / 4096 (  0)     0 /  512 (  0)
            Output Acl(PortAndVlan)     0 / 4096 (  0)     0 /  512 (  0)
            Output Acl(PortOrVlan)      0 / 4096 (  0)     0 /  512 (  0)
            Output Qos(PortAndVlan)     0 / 4096 (  0)     0 /  512 (  0)
            Output Qos(PortOrVlan)      0 / 4096 (  0)     0 /  512 (  0)

            L4Ops: used 2 out of 64
Switch# 

action

To specify an action to be taken when a match occurs in a VACL, use the action command. To remove an action clause, use the no form of this command.

action {drop | forward}

no action {drop | forward}

Syntax Description

drop

Sets the action to drop packets.

forward

Sets the action to forward packets to their destination.


Defaults

This command has no default settings.

Command Modes

VLAN access-map

Command History

Release
Modification

12.1(12c)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

In a VLAN access map, if at least one ACL is configured for a packet type (IP or MAC), the default action for the packet type is drop (deny).

If an ACL is not configured for a packet type, the default action for the packet type is forward (permit).

If an ACL for a packet type is configured and the ACL is empty or undefined, the configured action will be applied to the packet type.

Examples

This example shows how to define a drop action:

Switch(config-access-map)# action drop 
Switch(config-access-map)# 

This example shows how to define a forward action:

Switch(config-access-map)# action forward 
Switch(config-access-map)# 

Related Commands

match
show vlan access-map
vlan access-map

apply

To implement a new VLAN database, increment the configuration number, save the configuration number in NVRAM, and propagate the configuration number throughout the administrative domain, use the apply command.

apply

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

VLAN configuration

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

The apply command implements the configuration changes that you made after you entered VLAN database mode and uses them for the running configuration. This command keeps you in VLAN database mode.

You cannot use this command when the switch is in the VTP client mode.

You can verify that the VLAN database changes occurred by entering the show vlan command from privileged EXEC mode.

Examples

This example shows how to implement the proposed new VLAN database and to recognize it as the current database:

Switch(config-vlan)# apply
Switch(config-vlan)# 

Related Commands

abort (refer to Cisco IOS documentation)
exit (refer to Cisco IOS documentation)
reset
show vlan
shutdown vlan
(refer to Cisco IOS documentation)
vtp (global configuration mode)

arp access-list

To define an ARP access list or add clauses at the end of a predefined list, use the arp access-list command.

arp access-list name

Syntax Description

name

Specifies the access control list name.


Defaults

None

Command Modes

Configuration

Command History

Release
Modification

12.1(19)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to define an ARP access list named static-hosts:

Switch(config)# arp access-list static-hosts
Switch(config)# 

Related Commands

deny
ip arp inspection filter vlan
permit

attach module

To remotely connect to a specific module, use the attach module configuration command.

attach module mod

Syntax Description

mod

Target module for the command.


Defaults

This command has no default settings.

Command Modes

Privileged

Command History

Release
Modification

12.1(19)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

This command applies only to the Access Gateway Module on Catalyst 4500 series switches.

The valid values for mod depend on the chassis that are used. For example, if you have a Catalyst 4006 chassis, valid values for the module are from 2 to 6. If you have a 4507R chassis, valid values are from 3 to 7.

When you execute the attach module mod command, the prompt changes to Gateway#.

This command is identical in the resulting action to the session module mod and the remote login module mod commands.

Examples

This example shows how to remotely log in to an Access Gateway Module:

Switch# attach module 5
Attaching console to module 5
Type 'exit' at the remote prompt to end the session

Gateway> 

Related Commands

remote login module
session module

auto qos voip

To automatically configure quality of service (auto-QoS) for voice over IP (VoIP) within a QoS domain, use the auto qos voip interface configuration command. To change the auto-QoS configuration settings to the standard QoS defaults, use the no form of this command.

auto qos voip {cisco-phone | trust}

no auto qos voip {cisco-phone | trust}

Syntax Description

cisco-phone

Connects the interface to a Cisco IP phone and automatically configures QoS for VoIP. The CoS labels of incoming packets are trusted only when the telephone is detected.

trust

Connects the interface to a trusted switch or router and automatically configures QoS for VoIP. The CoS and DSCP labels of incoming packets are trusted.


Defaults

Auto-QoS is disabled on all interfaces.

Command Modes

Interface configuration

Command History

Release
Modification

12.1(19)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

Use this command to configure the QoS that is appropriate for VoIP traffic within the QoS domain. The QoS domain includes the switch, the interior of the network, and the edge devices that can classify incoming traffic for QoS.

Use the cisco-phone keyword on the ports at the edge of the network that are connected to Cisco IP phones. The switch detects the telephone through the Cisco Discovery Protocol (CDP) and trusts the CoS labels in packets that are received from the telephone.

Use the trust keyword on the ports that are connected to the interior of the network. Because it is assumed that the traffic has already been classified by the other edge devices, the CoS/DSCP labels in these packets are trusted.

When you enable the auto-QoS feature on the specified interface, these actions automatically occur:

QoS is globally enabled (qos global configuration command).

DBL is enabled globally (qos dbl global configuration command).

When you enter the auto qos voip cisco-phone interface configuration command, the trusted boundary feature is enabled. It uses the Cisco Discovery Protocol (CDP) to detect the presence or absence of a Cisco IP phone. When a Cisco IP phone is detected, the ingress classification on the specific interface is set to trust the CoS label that is received in the packet because some old phones do not mark DSCP. When a Cisco IP phone is absent, the ingress classification is set to not trust the CoS label in the packet.

When you enter the auto qos voip trust interface configuration command, the ingress classification on the specified interface is set to trust the CoS label that is received in the packet if the specified interface is configured as Layer 2 (and is set to trust DSCP if the interface is configured as Layer 3).

You can enable auto-QoS on static, dynamic-access, voice VLAN access, and trunk ports.

To display the QoS configuration that is automatically generated when auto-QoS is enabled, enable debugging before you enable auto-QoS. Use the debug auto qos privileged EXEC command to enable auto-QoS debugging.

To disable auto-QoS on an interface, use the no auto qos voip interface configuration command. When you enter this command, the switch enables standard QoS and changes the auto-QoS settings to the standard QoS default settings for that interface. This action will not change any global configuration performed by auto-QoS; the global configuration remains the same.

Examples

This example shows how to enable auto-QoS and to trust the CoS and DSCP labels that are received in the incoming packets when the switch or router that is connected to Gigabit Ethernet interface 1/1 is a trusted device:

Switch(config)# interface gigabitethernet1/1
Switch(config-if)# auto qos voip trust

This example shows how to enable auto-QoS and to trust the CoS labels that are received in incoming packets when the device connected to Fast Ethernet interface 2/1 is detected as a Cisco IP phone:

Switch(config)# interface fastethernet2/1
Switch(config-if)# auto qos voip cisco-phone

This example shows how to display the QoS configuration that is automatically generated when auto-QoS is enabled:

Switch# debug auto qos
AutoQoS debugging is on
Switch# config terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface gigabitethernet1/1
Switch(config-if)# auto qos voip trust
Switch(config-if)#
00:00:56:qos
00:00:57:qos map cos 3 to dscp 26
00:00:57:qos map cos 5 to dscp 46
00:00:58:qos map dscp 32 to tx-queue 1
00:00:58:qos dbl
00:01:00:policy-map autoqos-voip-policy
00:01:00:  class class-default
00:01:00:   dbl
00:01:00:interface GigabitEthernet1/1
00:01:00: qos trust cos
00:01:00: tx-queue 3
00:01:00:  priority high
00:01:00:  shape percent 33
00:01:00:  service-policy output autoqos-voip-policy
Switchconfig-if)# interface gigabitethernet1/1
Switch(config-if)# auto qos voip cisco-phone
Switch(config-if)#
00:00:55:qos
00:00:56:qos map cos 3 to dscp 26
00:00:57:qos map cos 5 to dscp 46
00:00:58:qos map dscp 32 to tx-queue 1
00:00:58:qos dbl
00:00:59:policy-map autoqos-voip-policy
00:00:59:  class class-default
00:00:59:   dbl
00:00:59:interface GigabitEthernet1/1
00:00:59: qos trust device cisco-phone
00:00:59: qos trust cos
00:00:59: tx-queue 3
00:00:59:  priority high
00:00:59:  shape percent 33
00:00:59:  bandwidth percent 33
00:00:59:  service-policy output autoqos-voip-policy

You can verify your settings by entering the show auto qos interface command.

Related Commands

debug auto qos (refer to Cisco IOS documentation)
qos map cos
qos trust
show auto qos
show qos
show qos interface
show qos maps

auto-sync

To enable automatic synchronization of the configuration files in NVRAM, use the auto-sync command. To disable automatic synchronization, use the no form of this command.

auto-sync {startup-config | config-register | bootvar | standard}

no auto-sync {startup-config | config-register | bootvar | standard}

Syntax Description

startup-config

Specifies automatic synchronization of the startup configuration.

config-register

Specifies automatic synchronization of the configuration register configuration.

bootvar

Specifies automatic synchronization of the BOOTVAR configuration.

standard

Specifies automatic synchronization of the startup configuration, BOOTVAR, and configuration registers.


Defaults

Standard automatic synchronization of all configuration files

Command Modes

Redundancy main-cpu

Command History

Release
Modification

12.1(12c)EW

Support for this command was introduced on the Catalyst 4500 series switch (Catalyst 4507R only).


Usage Guidelines

If you enter the no auto-sync standard command, no automatic synchronizations occur.

Examples

This example shows how (from the default configuration) to enable automatic synchronization of the configuration register in the main CPU:

Switch# config terminal
Switch (config)# redundancy
Switch (config-r)# main-cpu
Switch (config-r-mc)# no auto-sync standard
Switch (config-r-mc)# auto-sync configure-register
Switch (config-r-mc)# 

Related Commands

redundancy

channel-group

To assign and configure an EtherChannel interface to an EtherChannel group, use the channel-group command. To remove a channel group configuration from an interface, use the no form of this command.

channel-group number mode {active | on | auto [non-silent]} | {passive | desirable [non-silent]}

no channel-group

Syntax Description

number

Specifies the channel-group number; valid values are from 1 to 64.

mode

Specifies the EtherChannel mode of the interface.

active

Enables LACP unconditionally.

on

Forces the port to channel without PAgP.

auto

Places a port into a passive negotiating state, in which the port responds to PAgP packets it receives but does not initiate PAgP packet negotiation.

non-silent

(Optional) Used with the auto or desirable mode when traffic is expected from the other device.

passive

Enables LACP only if an LACP device is detected.

desirable

Places a port into an active negotiating state, in which the port initiates negotiations with other ports by sending PAgP packets.


Defaults

No channel groups are assigned.

Command Modes

Interface configuration

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.

12.1(13)EW

Support for LACP was added.


Usage Guidelines

You do not have to create a port-channel interface before assigning a physical interface to a channel group. If a port-channel interface has not been created, it is automatically created when the first physical interface for the channel group is created.

If a specific channel number is used for the PAgP-enabled interfaces of a channel group, that same channel number cannot be used for configuring a channel that has LACP-enabled interfaces or vice versa.

You can also create port channels by entering the interface port-channel command. This will create a Layer 3 port channel. To change the Layer 3 port channel into a Layer 2 port channel, use the switchport command before you assign physical interfaces to the channel group. A port channel cannot be changed from Layer 3 to Layer 2 or vice versa when it contains member ports.

You do not have to disable the IP address that is assigned to a physical interface that is part of a channel group, but we recommend that you do so.

Any configuration or attribute changes that you make to the port-channel interface are propagated to all interfaces within the same channel group as the port channel (for example, configuration changes are also propagated to the physical interfaces that are not part of the port channel, but are part of the channel group).

You can create in on mode a usable EtherChannel by connecting two port groups together.


Caution Do not enable Layer 3 addresses on the physical EtherChannel interfaces. Do not assign bridge groups on the physical EtherChannel interfaces because it creates loops.

Examples

This example shows how to add Gigabit Ethernet interface 1/1 to the EtherChannel group that is specified by port-channel 45:

Switch(config-if)# channel-group 45 mode on 
Creating a port-channel interface Port-channel45
Switch(config-if)# 

Related Commands

interface port-channel
show interfaces port-channel
(refer to Cisco IOS documentation)

channel-protocol

To enable LACP or PAgP on an interface, use the channel-protocol command. To disable the protocols, use the no form of this command.

channel-protocol {lacp | pagp}

no channel-protocol {lacp | pagp}

Syntax Description

lacp

Enables LACP to manage channeling.

pagp

Enables PAgP to manage channeling.


Defaults

PAgP

Command Modes

Interface configuration

Command History

Release
Modification

12.1(13)EW

Support for this command was introduced on the Catalyst 4500 series switches.


Usage Guidelines

This command is not supported on systems that are configured with a Supervisor Engine I.

You can also select the protocol using the channel-group command.

If the interface belongs to a channel, the no form of this command is rejected.

All ports in an EtherChannel must use the same protocol; you cannot run two protocols on one module.

PAgP and LACP are not compatible; both ends of a channel must use the same protocol.

You can manually configure a switch with PAgP on one side and LACP on the other side in the on mode.

You can change the protocol at any time, but this change causes all existing EtherChannels to reset to the default channel mode for the new protocol. You can use the channel-protocol command to restrict anyone from selecting a mode that is not applicable to the selected protocol.

Configure all ports in an EtherChannel to operate at the same speed and duplex mode (full duplex only for LACP mode).

For a complete list of guidelines, refer to the "Configuring EtherChannel" section of the Catalyst 4500 Series Switch Cisco IOS Software Configuration Guide.

Examples

This example shows how to select LACP to manage channeling on the interface:

Switch(config-if)# channel-protocol lacp
Switch(config-if)# 

Related Commands

channel-group
show etherchannel

class-map

To access the QoS class map configuration mode to configure QoS class maps, use the class-map command. To delete a class map, use the no form of this command.

class-map [match-all | match-any] name

no class-map [match-all | match-any] name

Syntax Description

match-all

(Optional) Specifies that all match criteria in the class map must be matched.

match-any

(Optional) Specifies that one or more match criteria must match.

name

Name of the class map.


Defaults

Match all criteria.

Command Modes

Global configuration

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

The name and acl_name arguments are case sensitive.

Use the class-map command and its subcommands on individual interfaces to define packet classification, marking, aggregate, and flow policing as part of a globally named service policy.

These commands are available in QoS class map configuration mode:

exit—Exits you from QoS class map configuration mode.

no—Removes a match statement from a class map.

match—Configures classification criteria.

These optional subcommands are also available:

access-group {acl_index | name acl_name}

ip {dscp | precedence} value1 value2... value8

any

The following subcommands appear in the CLI help, but they are not supported on LAN interfaces:

input-interface {interface interface_number | null number | vlan vlan_id}

protocol linktype

destination-address mac mac_address

source-address mac mac_address

qos-group

mpls

no

After you have configured the class map name and are in class map configuration mode, you can enter the match subcommands. The syntax for these subcommands is as follows:

match {[access-group {acl_index | name acl_name}] | [ip {dscp | precedence} value1 value2... value8]}

See Table 2-1 for a syntax description of the match subcommands.

Table 2-1 Syntax Description for the match Command

Optional Subcommand
Description

access-group acl_index | acl_name

Specifies the access list index or access list names; valid access list index values are from 1 to 2699.

access-group acl_name

Specifies the named access list.

ip dscp value1 value2 ... value8

Specifies the IP DSCP values to match; valid values are from 0 to 63. Enter up to eight DSCP values separated by white spaces.

ip precedence value1 value2 ... value8

Specifies the IP precedence values to match; valid values are from 0 to 7. Enter up to eight precedence values separated by white spaces.


Examples

This example shows how to access the class-map commands and subcommands and to configure a class map named ipp5 and enter a match statement for ip precedence 5:

Switch# config terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# class-map ipp5
Switch(config-cmap)# match ip precedence 5
Switch(config-cmap)# 

This example shows how to configure the class map to match an already configured access list:

Switch(config-cmap)# match access-group IPacl1
Switch(config-cmap)# 

Related Commands

policy-map
service-policy
show class-map
show policy-map
show policy-map interface

clear counters

To clear the interface counters, use the clear counters command.

clear counters [{FastEthernet interface_number} | {GigabitEthernet interface_number} |
{
null interface_number} | {port-channel number} | {vlan vlan_id}]

Syntax Description

FastEthernet interface_number

(Optional) Specifies the Fast Ethernet interface; valid values are from 1 to 9.

GigabitEthernet interface_number

(Optional) Specifies the Gigabit Ethernet interface; valid values are from 1 to 9.

null interface_number

(Optional) Specifies the null interface; the valid value is 0.

port-channel number

(Optional) Specifies the channel interface; valid values are from 1 to 64.

vlan vlan_id

(Optional) Specifies the VLAN; valid values are from 1 to 4096.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.

12.1(12c)EW

Support for extended VLAN addresses was added.


Usage Guidelines

This command clears all the current interface counters from all the interfaces unless you specify an interface.


Note This command does not clear the counters that are retrieved using SNMP, but only those seen when you enter the show interface counters command.


Examples

This example shows how to clear all the interface counters:

Switch# clear counters
Clear "show interface" counters on all interfaces [confirm] y
Switch# 

This example shows how to clear the counters on a specific interface:

Switch# clear counters vlan 200
Clear "show interface" counters on this interface [confirm]y
Switch# 

Related Commands

show interface counters (refer to Cisco IOS documentation)

clear hw-module slot password

To clear the password on an intelligent line module, use the clear hw-module slot password command.

clear hw-module slot slot_num password

Syntax Description

slot_num

Slot on a line module.


Defaults

The password is not cleared.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(18)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

You only need to change the password once unless the password is reset.

Examples

This example shows how to clear the password from slot 5 on a line module:

Switch# clear hw-module slot 5 password
Switch# 

Related Commands

hw-module power

clear interface gigabitethernet

To clear the hardware logic from a Gigabit Ethernet IEEE 802.3z interface, use the clear interface gigabitethernet command.

clear interface gigabitethernet slot/port

Syntax Description

slot/port

Number of the slot and port.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to clear the hardware logic from a Gigabit Ethernet IEEE 802.3z interface:

Switch# clear interface gigabitethernet 1/1
Switch# 

Related Commands

show interfaces status

clear interface vlan

To clear the hardware logic from a VLAN, use the clear interface vlan command.

clear interface vlan number

Syntax Description

number

Number of the VLAN interface; valid values are from 1 to 4094.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.

12.1(12c)EW

Support for extended VLAN addresses added.


Examples

This example shows how to clear the hardware logic from a specific VLAN:

Switch# clear interface vlan 5
Switch# 

Related Commands

show interfaces status

clear ip access-template

To clear the statistical information in access lists, use the clear ip access-template command.

clear ip access-template access-list

Syntax Description

access-list

Number of the access list; valid values are from 100 to 199 for an IP extended access list, and from 2000 to 2699 for an expanded range IP extended access list.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to clear the statistical information for an access list:

Switch# clear ip access-template 201
Switch# 

clear ip arp inspection log

To clear the status of the log buffer, use the clear ip arp inspection log command.

clear ip arp inspection log

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(19)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to clear the contents of the log buffer:

Switch# clear ip arp inspection log
Switch# 

Related Commands

arp access-list
show ip arp inspection log

clear ip arp inspection statistics

To clear the dynamic ARP inspection statistics, use the clear ip arp inspection statistics command.

clear ip arp inspection statistics [vlan vlan-range]

Syntax Description

vlan vlan-range

(Optional) Specifies the VLAN range.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(19)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to clear the DAI statistics from VLAN 1 and how to verify the removal:

Switch# clear ip arp inspection statistics vlan 1
Switch# show ip arp inspection statistics vlan 1

 Vlan      Forwarded        Dropped     DHCP Drops     ACL Drops 
 ----      ---------        -------     ----------     ----------
    1              0              0              0              0

 Vlan   DHCP Permits    ACL Permits   Source MAC Failures
 ----   ------------    -----------   -------------------
    1              0              0                    0

 Vlan   Dest MAC Failures   IP Validation Failures
 ----   -----------------   ----------------------
    1                  0                        0
Switch#

Related Commands

arp access-list
clear ip arp inspection log
show ip arp inspection

clear ip dhcp snooping database

To clear the DHCP binding database, use the clear ip dhcp snooping database command.

clear ip dhcp snooping database

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(19)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to clear the DHCP binding database:

Switch# clear ip dhcp snooping database
Switch# 

Related Commands

ip dhcp snooping
ip dhcp snooping binding interface
(refer to Cisco IOS documentation)
ip dhcp snooping information option
ip dhcp snooping trust
ip dhcp snooping vlan
show ip dhcp snooping
show ip dhcp snooping binding

clear ip dhcp snooping database statistics

To clear the DHCP binding database statistics, use the clear ip dhcp snooping database statistics command.

clear ip dhcp snooping database statistics

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(19)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to clear the DHCP binding database:

Switch# clear ip dhcp snooping database statistics
Switch# 

Related Commands

ip dhcp snooping
ip dhcp snooping binding
ip dhcp snooping information option
ip dhcp snooping trust
ip dhcp snooping vlan
show ip dhcp snooping
show ip dhcp snooping binding

clear ip igmp group

To delete the IGMP group cache entries, use the clear ip igmp group command.

clear ip igmp group [{fastethernet slot/port} | {GigabitEthernet slot/port} | {host_name | group_address} {Loopback interface_number} | {null interface_number} |
{
port-channel number} | {vlan vlan_id}]

Syntax Description

fastethernet

(Optional) Specifies the Fast Ethernet interface.

slot/port

(Optional) Number of the slot and port.

GigabitEthernet

(Optional) Specifies the Gigabit Ethernet interface.

host_name

(Optional) Hostname, as defined in the DNS hosts table or with the ip host command.

group_address

(Optional) Address of the multicast group in four-part, dotted notation.

Loopback interface_number

(Optional) Specifies the loopback interface; valid values are from 0 to 2,147,483,647.

null interface_number

(Optional) Specifies the null interface; the valid value is 0.

port-channel number

(Optional) Specifies the channel interface; valid values are from 1 to 64.

vlan vlan_id

(Optional) Specifies the VLAN; valid values are from 1 to 4094.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

The IGMP cache contains a list of the multicast groups of which hosts on the directly connected LAN are members.

To delete all the entries from the IGMP cache, enter the clear ip igmp group command with no arguments.

Examples

This example shows how to clear the entries for a specific group from the IGMP cache:

Switch# clear ip igmp group 224.0.255.1
Switch# 

This example shows how to clear the IGMP group cache entries from a specific interface:

Switch# clear ip igmp group gigabitethernet 2/2
Switch# 

Related Commands

ip host (refer to Cisco IOS documentation)
show ip igmp groups (refer to Cisco IOS documentation)
show ip igmp interface

clear ip igmp snooping membership

To clear the explicit host tracking database, use the clear ip igmp snooping membership command.

clear ip igmp snooping membership [vlan vlan_id]

Syntax Description

vlan vlan_id

(Optional) Specifies a VLAN; valid values are from 1 to 1001 and from 1006 to 4094.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(20)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

By default, the explicit host tracking database maintains a maximum of 1-KB entries. After you reach this limit, no additional entries can be created in the database. To create more entries, you will need to delete the database with the clear ip igmp snooping statistics vlan command.

Examples

This example shows how to display the IGMP snooping statistics for VLAN 25:

Switch# clear ip igmp snooping membership vlan 25
Switch#

Related Commands

ip igmp snooping vlan explicit-tracking
show ip igmp snooping membership

clear ip mfib counters

To clear the global MFIB counters and the counters for all active MFIB routes, use the clear ip mfib counters command.

clear ip mfib counters

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to clear all the active MFIB routes and global counters:

Switch# clear ip mfib counters
Switch# 

Related Commands

show ip mfib

clear ip mfib fastdrop

To clear all the MFIB fast-drop entries, use the clear ip mfib fastdrop command.

clear ip mfib fastdrop

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

If new fast-dropped packets arrive, the new fast-drop entries are created.

Examples

This example shows how to clear all the fast-drop entries:

Switch# clear ip mfib fastdrop
Switch# 

Related Commands

ip mfib fastdrop
show ip mfib fastdrop

clear lacp counters

To clear the statistics for all the interfaces belonging to a specific channel group, use the clear lacp counters command.

clear lacp [channel-group] counters

Syntax Description

channel-group

(Optional) Channel-group number; valid values are from 1 to 64.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC mode

Command History

Release
Modification

12.1(13)EW

Support for this command was introduced on the Catalyst 4500 series switches.


Usage Guidelines

This command is not supported on systems that are configured with a Supervisor Engine I.

If you do not specify a channel group, all channel groups are cleared.

If you enter this command for a channel group that contains members in PAgP mode, the command is ignored.

Examples

This example shows how to clear the statistics for a specific group:

Switch# clear lacp 1 counters
Switch# 

Related Commands

show lacp

clear mac-address-table dynamic

To clear the dynamic address entries from the Layer 2 MAC address table, use the clear mac-address-table dynamic command.

clear mac-address-table dynamic [{address mac_addr} | {interface interface}] [vlan vlan_id]

Syntax Description

address mac_addr

(Optional) Specifies the MAC address.

interface interface

(Optional) Specifies the interface and clears the entries associated with it; valid values are FastEthernet and GigabitEthernet.

vlan vlan_id

(Optional) Specifies the VLANs; valid values are from 1 to 4094.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.

12.1(12c)EW

Support for extended VLAN addresses added.


Usage Guidelines

Enter the clear mac-address-table dynamic command with no arguments to remove all dynamic entries from the table.

Examples

This example shows how to clear all the dynamic Layer 2 entries for a specific interface (gi1/1):

Switch# clear mac-address-table dynamic interface gi1/1
Switch# 

Related Commands

mac-address-table aging-time
main-cpu
show mac-address-table address

clear pagp

To clear the port-channel information, use the clear pagp command.

clear pagp {group-number | counters}

Syntax Description

group-number

Channel-group number; valid values are from 1 to 64.

counters

Clears traffic filters.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to clear the port-channel information for a specific group:

Switch# clear pagp 32
Switch# 

This example shows how to clear all the port-channel traffic filters:

Switch# clear pagp counters
Switch# 

Related Commands

show pagp

clear port-security

To delete all configured secure addresses or a specific dynamic or sticky secure address on an interface from the MAC address table, use the clear port-security command.

clear port-security {all | dynamic} [address mac-addr [vlan vlan-id]] | [interface interface-id]

Syntax Description

all

Deletes all the secure MAC addresses.

dynamic

Deletes all the dynamic secure MAC addresses.

address mac-addr

(Optional) Deletes the specified secure MAC address.

vlan vlan-id

(Optional) Deletes the specified secure MAC address from the specified VLAN.

interface interface-id

(Optional) Deletes the secure MAC addresses on the specified physical port or port channel.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Usage Guidelines

If you enter the clear port-security all command, the switch removes all the secure MAC addresses from the MAC address table.

If you enter the clear port-security dynamic interface interface-id command, the switch removes all the dynamic secure MAC addresses on an interface from the MAC address table.

Command History

Release
Modification

12.2(18)EW

This command was first introduced on the Catalyst 4500 series switch.


Examples

This example shows how to remove all the secure addresses from the MAC address table:

Switch# clear port-security all

This example shows how to remove a dynamic secure address from the MAC address table:

Switch# clear port-security dynamic address 0008.0070.0007

This example shows how to remove all the dynamic secure addresses learned on a specific interface:

Switch# clear port-security dynamic interface gigabitethernet0/1

You can verify that the information was deleted by entering the show port-security command.

Related Commands

show port-security
switchport port-security

clear qos

To clear the global and per-interface aggregate QoS counters, use the clear qos command.

clear qos [aggregate-policer [name] | interface {{fastethernet | GigabitEthernet} {slot/interface}} | vlan {vlan_num} | port-channel {number}]

Syntax Description

aggregate-policer name

(Optional) Specifies an aggregate policer.

interface

(Optional) Specifies an interface.

fastethernet

(Optional) Specifies the Fast Ethernet 802.3 interface.

GigabitEthernet

(Optional) Specifies the Gigabit Ethernet 802.3z interface.

slot/interface

(Optional) Number of the slot and interface.

vlan vlan_num

(Optional) Specifies a VLAN.

port-channel number

(Optional) Specifies the channel interface; valid values are from 1 to 64.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines


Note When you enter the clear qos command, the way that the counters work is affected and the traffic that is normally restricted could be forwarded for a short period of time.


The clear qos command resets the interface QoS policy counters. If no interface is specified, the clear qos command resets the QoS policy counters for all interfaces.

Examples

This example shows how to clear the global and per-interface aggregate QoS counters for all the protocols:

Switch# clear qos
Switch# 

This example shows how to clear the specific protocol aggregate QoS counters for all the interfaces:

Switch# clear qos aggregate-policer 
Switch# 

Related Commands

show qos

clear vlan counters

To clear the software-cached counter values to start from zero again for a specified VLAN or all existing VLANs, use the clear vlan counters command.

clear vlan [vlan-id] counters

Syntax Description

vlan-id

(Optional) VLAN number; see the "Usage Guidelines" section for valid values.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(13)EW

Support for this command was introduced on the Catalyst 4500 series switches.


Usage Guidelines

If you do not specify a vlan-id value; the software-cached counter values for all the existing VLANs are cleared.

Examples

Switch# clear vlan 10 counters
Clear "show vlan" counters on this vlan [confirm]y
Switch# 

Related Commands

show vlan counters

clear vmps statistics

To clear the VMPS statistics, use the clear vmps statistics command.

clear vmps statistics

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(13)EW

Support for this command was introduced on the Catalyst 4500 series switches.


Examples

Switch# clear vmps statistics
Switch# 

Related Commands

show vmps
vmps reconfirm (privileged EXEC)

debug adjacency

To display information about the adjacency debugging, use the debug adjacency command. To disable debugging output, use the no form of this command.

debug adjacency [ipc]

no debug adjacency

Syntax Description

ipc

(Optional) Displays the IPC entries in the adjacency database.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to display the information in the adjacency database:

Switch# debug adjacency
4d02h: ADJ: add 172.20.52.36 (GigabitEthernet1/1) via ARP will expire: 04:00:00
4d02h: ADJ: add 172.20.52.36 (GigabitEthernet1/1) via ARP will expire: 04:00:00
4d02h: ADJ: add 172.20.52.36 (GigabitEthernet1/1) via ARP will expire: 04:00:00
4d02h: ADJ: add 172.20.52.36 (GigabitEthernet1/1) via ARP will expire: 04:00:00
4d02h: ADJ: add 172.20.52.36 (GigabitEthernet1/1) via ARP will expire: 04:00:00
4d02h: ADJ: add 172.20.52.36 (GigabitEthernet1/1) via ARP will expire: 04:00:00
4d02h: ADJ: add 172.20.52.36 (GigabitEthernet1/1) via ARP will expire: 04:00:00
4d02h: ADJ: add 172.20.52.36 (GigabitEthernet1/1) via ARP will expire: 04:00:00
<... output truncated...>
Switch# 

Related Commands

undebug adjacency (same as no debug adjacency)

debug backup

To debug the backup events, use the debug backup command. To disable the debugging output, use the no form of this command.

debug backup

no debug backup

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to debug the backup events:

Switch# debug backup
Backup events debugging is on
Switch# 

Related Commands

undebug backup (same as no debug backup)

debug condition interface

To limit the debugging output of interface-related activities, use the debug condition interface command. To disable the debugging output, use the no form of this command.

debug condition interface {fastethernet slot/port | GigabitEthernet slot/port |
null interface_num | port-channel interface-num | vlan vlan_id}

no debug condition interface {fastethernet slot/port | GigabitEthernet slot/port | null interface_num | port-channel interface-num | vlan vlan_id}

Syntax Description

fastethernet

Limits the debugging to Fast Ethernet interfaces.

slot/port

Number of the slot and port.

GigabitEthernet

Limits the debugging to Gigabit Ethernet interfaces.

null interface-num

Limits the debugging to null interfaces; the valid value is 0.

port-channel interface-num

Limits the debugging to port-channel interfaces; valid values are from 1 to 64.

vlan vlan_id

Specifies the VLAN interface number; valid values are from 1 to 4094.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.

12.1(12c)EW

Support for extended VLAN addresses added.


Examples

This example shows how to limit the debugging output to VLAN interface 1:

Switch# debug condition interface vlan 1
Condition 2 set
Switch# 

Related Commands

debug interface
undebug condition interface
(same as no debug condition interface)

debug condition standby

To limit the debugging output for the standby state changes, use the debug condition standby command. To disable the debugging output, use the no form of this command.

debug condition standby {fastethernet slot/port | GigabitEthernet slot/port |
port-channel interface-num | vlan vlan_id group-number}

no debug condition standby {fastethernet slot/port | GigabitEthernet slot/port |
port-channel interface-num | vlan vlan_id group-number}

Syntax Description

fastethernet

Limits the debugging to Fast Ethernet interfaces.

slot/port

Number of the slot and port.

GigabitEthernet

Limits the debugging to Gigabit Ethernet interfaces.

port-channel interface_num

Limits the debugging output to port-channel interfaces; valid values are from 1 to 64.

vlan vlan_id

Limits the debugging of a condition on a VLAN interface; valid values are from 1 to 4094.

group-number

VLAN group number; valid values are from 0 to 255.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.

12.1(12c)EW

Support for extended VLAN addresses added.


Usage Guidelines

If you attempt to remove the only condition set, you will be prompted with a message asking if you want to abort the removal operation. You can enter n to abort the removal or y to proceed with the removal. If you remove the only condition set, an excessive number of debugging messages might occur.

Examples

This example shows how to limit the debugging output to group 0 in VLAN 1:

Switch# debug condition standby vlan 1 0
Condition 3 set
Switch# 

This example shows the display if you try to turn off the last standby debug condition:

Switch# no debug condition standby vlan 1 0
This condition is the last standby condition set.
Removing all conditions may cause a flood of debugging
messages to result, unless specific debugging flags
are first removed.

Proceed with removal? [yes/no]: n
% Operation aborted     
Switch#           

Related Commands

undebug condition standby (same as no debug condition standby)

debug condition vlan

To limit the VLAN debugging output for a specific VLAN, use the debug condition vlan command. To disable the debugging output, use the no form of this command.

debug condition vlan {vlan_id}

no debug condition vlan {vlan_id}

Syntax Description

vlan_id

Number of the VLAN; valid values are from 1 to 4096.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.

12.1(12c)EW

Support for extended VLAN addresses added.


Usage Guidelines

If you attempt to remove the only VLAN condition set, you will be prompted with a message asking if you want to abort the removal operation. You can enter n to abort the removal or y to proceed with the removal. If you remove the only condition set, it could result in the display of an excessive number of messages.

Examples

This example shows how to limit the debugging output to VLAN 1:

Switch# debug condition vlan 1
Condition 4 set
Switch# 

This example shows the message that is displayed when you attempt to disable the last VLAN debug condition:

Switch# no debug condition vlan 1
This condition is the last vlan condition set.
Removing all conditions may cause a flood of debugging
messages to result, unless specific debugging flags
are first removed.

Proceed with removal? [yes/no]: n
% Operation aborted     
Switch# 

Related Commands

undebug condition vlan (same as no debug condition vlan)

debug dot1x

To enable the debugging for the 802.1X feature, use the debug dot1x command. To disable the debugging output, use the no form of this command.

debug dot1x {all | errors | events | packets | registry | state-machine}

no debug dot1x {all | errors | events | packets | registry | state-machine}

Syntax Description

all

Enables the debugging of all conditions.

errors

Enables the debugging of print statements guarded by the dot1x error flag.

events

Enables the debugging of print statements guarded by the dot1x events flag.

packets

All incoming dot1x packets are printed with packet and interface information.

registry

Enables the debugging of print statements guarded by the dot1x registry flag.

state-machine

Enables the debugging of print statements guarded by the dot1x registry flag.


Defaults

Debugging is disabled.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(12c)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to enable the 802.1X debugging for all conditions:

Switch# debug dot1x all
Switch# 

Related Commands

show dot1x
undebug dot1x
(same as no debug dot1x)

debug etherchnl

To debug EtherChannel, use the debug etherchnl command. To disable the debugging output, use the no form of this command.

debug etherchnl [all | detail | error | event | idb | linecard]

no debug etherchnl

Syntax Description

all

(Optional) Displays all EtherChannel debug messages.

detail

(Optional) Displays the detailed EtherChannel debug messages.

error

(Optional) Displays the EtherChannel error messages.

event

(Optional) Debugs the major EtherChannel event messages.

idb

(Optional) Debugs the PAgP IDB messages.

linecard

(Optional) Debugs the SCP messages to the module.


Defaults

The default settings are as follows:

Debug is disabled.

All messages are displayed.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

If you do not specify a keyword, all debug messages are displayed.

Examples

This example shows how to display all the EtherChannel debug messages:

Switch# debug etherchnl
PAgP Shim/FEC debugging is on
22:46:30:FEC:returning agport Po15 for port (Fa2/1)
22:46:31:FEC:returning agport Po15 for port (Fa4/14)
22:46:33:FEC:comparing GC values of Fa2/25 Fa2/15 flag = 1 1
22:46:33:FEC:port_attrib:Fa2/25 Fa2/15 same
22:46:33:FEC:EC - attrib incompatable for Fa2/25; duplex of Fa2/25 is half, Fa2/15 is full
22:46:33:FEC:pagp_switch_choose_unique:Fa2/25, port Fa2/15 in agport Po3 is incompatable
Switch# 

This example shows how to display the EtherChannel IDB debug messages:

Switch# debug etherchnl idb
Agport idb related debugging is on
Switch# 

This example shows how to disable the debugging:

Switch# no debug etherchnl
Switch# 

Related Commands

undebug etherchnl (same as no debug etherchnl)

debug interface

To abbreviate the entry of the debug condition interface command, use the debug interface command. To disable debugging output, use the no form of this command.

debug interface {FastEthernet slot/port | GigabitEthernet slot/port | null |
port-channel interface-num | vlan vlan_id}

no debug interface {FastEthernet slot/port | GigabitEthernet slot/port | null |
port-channel interface-num | vlan vlan_id}

Syntax Description

FastEthernet

Limits the debugging to Fast Ethernet interfaces.

slot/port

Number of the slot and port.

GigabitEthernet

Limits the debugging to Gigabit Ethernet interfaces.

null

Limits the debugging to null interfaces; the only valid value is 0.

port-channel interface-num

Limits the debugging to port-channel interfaces; valid values are from 1 to 64.

vlan vlan_id

Specifies the VLAN interface number; valid values are from 1 to 4094.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.

12.1(12c)EW

Support for extended VLAN addresses added.


Examples

This example shows how to limit the debugging to interface VLAN 1:

Switch# debug interface vlan 1
Condition 1 set
Switch# 

Related Commands

debug condition interface
undebug interface
(same as no debug interface)

debug ipc

To debug the IPC activity, use the debug ipc command. To disable the debugging output, use the no form of this command.

debug ipc {all | errors | events | headers | packets | ports | seats}

no debug ipc {all | errors | events | headers | packets | ports | seats}

Syntax Description

all

Enables all IPC debugging.

errors

Enables the IPC error debugging.

events

Enables the IPC event debugging.

headers

Enables the IPC header debugging.

packets

Enables the IPC packet debugging.

ports

Enables the debugging of the creation and deletion of ports.

seats

Enables the debugging of the creation and deletion of nodes.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(12c)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to enable the debugging of the IPC events:

Switch# debug ipc events
Special Events debugging is on
Switch# 

Related Commands

undebug ipc (same as no debug ipc)

debug ip dhcp snooping event

To debug the DHCP snooping events, use the debug ip dhcp snooping event command. To disable debugging output, use the no form of this command.

debug ip dhcp snooping event

no debug ip dhcp snooping event

Syntax Description

This command has no arguments or keywords.

Defaults

Debugging of snooping event is disabled.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(12c)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to enable the debugging for the DHCP snooping events:

Switch# debug ip dhcp snooping event
Switch# 

This example shows how to disable the debugging for the DHCP snooping events:

Switch# no debug ip dhcp snooping event
Switch# 

Related Commands

debug ip dhcp snooping packet

debug ip dhcp snooping packet

To debug the DHCP snooping messages, use the debug ip dhcp snooping packet command. To disable the debugging output, use the no form of this command.

debug ip dhcp snooping packet

no debug ip dhcp snooping packet

Syntax Description

This command has no arguments or keywords.

Defaults

Debugging of snooping packet is disabled.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(12c)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to enable the debugging for the DHCP snooping packets:

Switch# debug ip dhcp snooping packet
Switch# 

This example shows how to disable the debugging for the DHCP snooping packets:

Switch# no debug ip dhcp snooping packet
Switch# 

Related Commands

debug ip dhcp snooping event

debug ip verify source packet

To debug the IP source guard messages, use the debug ip verify source packet command. To disable the debugging output, use the no form of this command.

debug ip verify source packet

no debug ip verify source packet

Syntax Description

This command has no arguments or keywords.

Defaults

Debugging of snooping security packets is disabled.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(12c)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to enable debugging for the IP source guard:

Switch# debug ip verify source packet
Switch# 

This example shows how to disable debugging for the IP source guard:

Switch# no debug ip verify source packet
Switch# 

Related Commands

ip dhcp snooping
ip dhcp snooping information option
ip dhcp snooping limit rate
ip dhcp snooping trust
ip verify source vlan dhcp-snooping
(refer to Cisco IOS documentation)
show ip dhcp snooping
show ip dhcp snooping binding
show ip verify source
(refer to Cisco IOS documentation)

debug lacp

To debug the LACP activity, use the debug lacp command. To disable the debugging output, use the no form of this command.

debug lacp [all | event | fsm | misc | packet]

no debug lacp

Syntax Description

all

(Optional) Enables all LACP debugging.

event

(Optional) Enables the debugging of the LACP events.

fsm

(Optional) Enables the debugging of the LACP finite state machine.

misc

(Optional) Enables the miscellaneous LACP debugging.

packet

(Optional) Enables the LACP packet debugging.


Defaults

Debugging of LACP activity is disabled.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(13)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

This command is supported only by the supervisor engine and can be entered only from the Catalyst 4500 series switch console.

Examples

This example shows how to enable the LACP miscellaneous debugging:

Switch# debug lacp 
Port Aggregation Protocol Miscellaneous debugging is on
Switch#                                                           

Related Commands

undebug pagp (same as no debug pagp)

debug monitor

To display the monitoring activity, use the debug monitor command. To disable the debugging output, use the no form of this command.

debug monitor {all | errors | idb-update | list | notifications | platform | requests}

no debug monitor {all | errors | idb-update | list | notifications | platform | requests}

Syntax Description

all

Displays all the SPAN debugging messages.

errors

Displays the SPAN error details.

idb-update

Displays the SPAN IDB update traces.

list

Displays the SPAN list tracing and the VLAN list tracing.

notifications

Displays the SPAN notifications.

platform

Displays the SPAN platform tracing.

requests

Displays the SPAN requests.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to debug the monitoring errors:

Switch# debug monitor errors
SPAN error detail debugging is on
Switch# 

Related Commands

undebug monitor (same as no debug monitor)

debug nvram

To debug the NVRAM activity, use the debug nvram command. To disable the debugging output, use the no form of this command.

debug nvram

no debug nvram

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to debug NVRAM:

Switch# debug nvram
NVRAM behavior debugging is on
Switch# 

Related Commands

undebug nvram (same as no debug nvram)

debug pagp

To debug the PAgP activity, use the debug pagp command. To disable the debugging output, use the no form of this command.

debug pagp [all | event | fsm | misc | packet]

no debug pagp

Syntax Description

all

(Optional) Enables all PAgP debugging.

event

(Optional) Enables the debugging of the PAgP events.

fsm

(Optional) Enables the debugging of the PAgP finite state machine.

misc

(Optional) Enables the miscellaneous PAgP debugging.

packet

(Optional) Enables the PAgP packet debugging.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

This command is supported only by the supervisor engine and can be entered only from the Catalyst 4500 series switch console.

Examples

This example shows how to enable the PAgP miscellaneous debugging:

Switch# debug pagp misc
Port Aggregation Protocol Miscellaneous debugging is on
Switch# 
*Sep 30 10:13:03: SP: PAgP: pagp_h(Fa5/6) expired
*Sep 30 10:13:03: SP: PAgP: 135 bytes out Fa5/6
*Sep 30 10:13:03: SP: PAgP: Fa5/6 Transmitting information packet
*Sep 30 10:13:03: SP: PAgP: timer pagp_h(Fa5/6) started with interval 30000
<... output truncated...>
Switch# 

Related Commands

undebug pagp (same as no debug pagp)

debug platform packet protocol lacp

To debug the LACP protocol packets, use the debug platform packet protocol lacp command. To disable the debugging output, use the no form of this command.

debug platform packet protocol lacp [receive | transmit | vlan]

no debug platform packet protocol lacp [receive | transmit | vlan]

Syntax Description

receive

(Optional) Enables the platform packet reception debugging functions.

transmit

(Optional) Enables the platform packet transmission debugging functions.

vlan

(Optional) Enables the platform packet VLAN debugging functions.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to enable all PM debugging:

Switch# debug platform packet protocol lacp
Switch# 

Related Commands

undebug platform packet protocol lacp (same as no debug platform packet protocol lacp)

debug platform packet protocol pagp

To debug the PAgP protocol packets, use the debug platform packet protocol pagp command. To disable the debugging output, use the no form of this command.

debug platform packet protocol pagp [receive | transmit | vlan]

no debug platform packet protocol pagp [receive | transmit | vlan]

Syntax Description

receive

(Optional) Enables the platform packet reception debugging functions.

transmit

(Optional) Enables the platform packet transmission debugging functions.

vlan

(Optional) Enables the platform packet VLAN debugging functions.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(13)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to enable all PM debugging:

Switch# debug platform packet protocol pagp
Switch# 

Related Commands

undebug platform packet protocol pagp (same as no debug platform packet protocol pagp)

debug pm

To debug the port manager (PM) activity, use the debug pm command. To disable the debugging output, use the no form of this command.

debug pm {all | card | cookies | etherchnl | messages | port | registry | scp | sm | span | split |
vlan | vp}

no debug pm {all | card | cookies | etherchnl | messages | port | registry | scp | sm | span | split |
vlan
| vp}

Syntax Description

all

Displays all PM debugging messages.

card

Debugs the module-related events.

cookies

Enables the internal PM cookie validation.

etherchnl

Debugs the EtherChannel-related events.

messages

Debugs the PM messages.

port

Debugs the port-related events.

registry

Debugs the PM registry invocations.

scp

Debugs the SCP module messaging.

sm

Debugs the state machine-related events.

span

Debugs the spanning-tree-related events.

split

Debugs the split-processor.

vlan

Debugs the VLAN-related events.

vp

Debugs the virtual port-related events.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to enable all PM debugging:

Switch# debug pm all
Switch# 

Related Commands

undebug pm (same as no debug pm)

debug psecure

To debug port security, use the debug psecure command. To disable the debugging output, use the no form of this command.

debug psecure

no debug psecure

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(13)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to enable all PM debugging:

Switch# debug psecure
Switch# 

Related Commands

switchport port-security

debug redundancy

To debug the supervisor engine redundancy, use the debug redundancy command. To disable the debugging output, use the no form of this command.

debug redundancy {errors | fsm | kpa | msg | progression | status | timer}

no debug redundancy

Syntax Description

errors

Enables the redundancy facility for error debugging.

fsm

Enables the redundancy facility for FSM event debugging.

kpa

Enables the redundancy facility for keepalive debugging.

msg

Enables the redundancy facility for messaging event debugging.

progression

Enables the redundancy facility for progression event debugging.

status

Enables the redundancy facility for status event debugging.

timer

Enables the redundancy facility for timer event debugging.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(12c)EW

Support for this command was introduced on the Catalyst 4500 series switch (Catalyst 4507R only).


Examples

This example shows how to debug the redundancy facility timer event debugging:

Switch# debug redundancy timer
Redundancy timer debugging is on
Switch# 

debug smf updates

To debug the software MAC filter (SMF) address insertions and deletions, use the debug smf updates command. To disable the debugging output, use the no form of this command.

debug smf updates

no debug smf updates

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to debug the SMF updates:

Switch# debug smf updates
Software MAC filter address insertions and deletions debugging is on
Switch# 

Related Commands

undebug smf (same as no debug smf)

debug spanning-tree

To debug the spanning-tree activities, use the debug spanning-tree command. To disable the debugging output, use the no form of this command.

debug spanning-tree {all | bpdu | bpdu-opt | etherchannel | config | events | exceptions |
general | mst | pvst+ | root | snmp}

no debug spanning-tree {all | bpdu | bpdu-opt | etherchannel | config | events | exceptions | general | mst | pvst+ | root | snmp}

Syntax Description

all

Displays all the spanning-tree debugging messages.

bpdu

Debugs the spanning-tree BPDU.

bpdu-opt

Debugs the optimized BPDU handling.

etherchannel

Debugs the spanning-tree EtherChannel support.

config

Debugs the spanning-tree configuration changes.

events

Debugs the TCAM events.

exceptions

Debugs the spanning-tree exceptions.

general

Debugs the general spanning-tree activity.

mst

Debugs the multiple spanning-tree events.

pvst+

Debugs the PVST+ events.

root

Debugs the spanning-tree root events.

snmp

Debugs the spanning-tree SNMP events.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to debug the spanning-tree PVST+:

Switch# debug spanning-tree pvst+
Spanning Tree PVST+ debugging is on
Switch# 

Related Commands

undebug spanning-tree (same as no debug spanning-tree)

debug spanning-tree backbonefast

To enable debugging of the spanning-tree BackboneFast events, use the debug spanning-tree backbonefast command. To disable the debugging output, use the no form of this command.

debug spanning-tree backbonefast [detail | exceptions]

no debug spanning-tree backbonefast

Syntax Description

detail

(Optional) Displays the detailed BackboneFast debugging messages.

exceptions

(Optional) Enables the debugging of spanning-tree BackboneFast exceptions.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

This command is supported only by the supervisor engine and can be entered only from the Catalyst 4500 series switch console.

Examples

This example shows how to enable the debugging and to display the detailed spanning-tree BackboneFast debugging information:

Switch# debug spanning-tree backbonefast detail
Spanning Tree backbonefast detail debugging is on
Switch# 

Related Commands

undebug spanning-tree backbonefast (same as no debug spanning-tree backbonefast)

debug spanning-tree switch

To enable the switch shim debugging, use the debug spanning-tree switch command. To disable the debugging output, use the no form of this command.

debug spanning-tree switch {all | errors | general | pm | rx {decode | errors | interrupt |
process} | state | tx [decode]}

no debug spanning-tree switch {all | errors | general | pm | rx {decode | errors | interrupt | process} | state | tx [decode]}

Syntax Description

all

Displays all the spanning-tree switch shim debugging messages.

errors

Enables the debugging of switch shim errors or exceptions.

general

Enables the debugging of general events.

pm

Enables the debugging of port manager events.

rx

Displays the received BPDU-handling debugging messages.

decode

Enables the debugging of the decode-received packets of the spanning-tree switch shim.

errors

Enables the debugging of the receive errors of the spanning-tree switch shim.

interrupt

Enables the shim ISR receive BPDU debugging on the spanning-tree switch.

process

Enables the process receive BPDU debugging on the spanning-tree switch.

state

Enables the debugging of the state changes on the spanning-tree port.

tx

Enables the transmit BPDU debugging on the spanning-tree switch shim.

decode

(Optional) Enables the decode-transmitted packets debugging on the spanning-tree switch shim.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

This command is supported only by the supervisor engine and can be entered only from the switch console.

Examples

This example shows how to enable the transmit BPDU debugging on the spanning-tree switch shim:

Switch# debug spanning-tree switch tx
Spanning Tree Switch Shim transmit bpdu debugging is on
*Sep 30 08:47:33: SP: STP SW: TX: bpdu of type ieee-st size 92 on FastEthernet5/9 303
*Sep 30 08:47:33: SP: STP SW: TX: bpdu of type ieee-st size 92 on FastEthernet5/9 304
*Sep 30 08:47:33: SP: STP SW: TX: bpdu of type ieee-st size 92 on FastEthernet5/9 305
*Sep 30 08:47:33: SP: STP SW: TX: bpdu of type ieee-st size 92 on FastEthernet5/9 349
*Sep 30 08:47:33: SP: STP SW: TX: bpdu of type ieee-st size 92 on FastEthernet5/9 350
*Sep 30 08:47:33: SP: STP SW: TX: bpdu of type ieee-st size 92 on FastEthernet5/9 351
*Sep 30 08:47:33: SP: STP SW: TX: bpdu of type ieee-st size 92 on FastEthernet5/9 801
<... output truncated...>
Switch# 

Related Commands

undebug spanning-tree switch (same as no debug spanning-tree switch)

debug spanning-tree uplinkfast

To enable the debugging of the spanning-tree UplinkFast events, use the debug spanning-tree uplinkfast command. To disable the debugging output, use the no form of this command.

debug spanning-tree uplinkfast [exceptions]

no debug spanning-tree uplinkfast

Syntax Description

exceptions

(Optional) Enables the debugging of the spanning-tree UplinkFast exceptions.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

This command is supported only by the supervisor engine and can be entered only from the switch console.

Examples

This example shows how to debug the spanning-tree UplinkFast exceptions:

Switch# debug spanning-tree uplinkfast exceptions
Spanning Tree uplinkfast exceptions debugging is on
Switch# 

Related Commands

undebug spanning-tree uplinkfast (same as no debug spanning-tree uplinkfast)

debug sw-vlan

To debug the VLAN manager activities, use the debug sw-vlan command. To disable the debugging output, use the no form of this command.

debug sw-vlan {badpmcookies | events | management | packets | registries}

no debug sw-vlan {badpmcookies | events | management | packets | registries}

Syntax Description

badpmcookies

Displays the VLAN manager incidents of bad port-manager cookies.

events

Debugs the VLAN manager events.

management

Debugs the VLAN manager management of internal VLANs.

packets

Debugs the packet handling and encapsulation processes.

registries

Debugs the VLAN manager registries.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to debug the software VLAN events:

Switch# debug sw-vlan events
vlan manager events debugging is on
Switch# 

Related Commands

undebug sw-vlan (same as no debug sw-vlan)

debug sw-vlan ifs

To enable the VLAN manager Cisco IOS file system (IFS) error tests, use the debug sw-vlan ifs command. To disable the debugging output, use the no form of this command.

debug sw-vlan ifs {open {read | write} | read {1 | 2 | 3 | 4} | write}

no debug sw-vlan ifs {open {read | write} | read {1 | 2 | 3 | 4} | write}

Syntax Description

open

Enables the VLAN manager IFS debugging of errors in an IFS file-open operation.

read

Debugs the errors that occurred when the IFS VLAN configuration file was open for reading.

write

Debugs the errors that occurred when the IFS VLAN configuration file was open for writing.

{1 | 2 | 3 | 4}

Determines the file-read operation. See the "Usage Guidelines" section for information about operation levels.

write

Debugs the errors that occurred during an IFS file-write operation.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

The following are four types of file read operations:

Operation 1—Reads the file header, which contains the header verification word and the file version number.

Operation 2—Reads the main body of the file, which contains most of the domain and VLAN information.

Operation 3—Reads TLV descriptor structures.

Operation 4—Reads TLV data.

Examples

This example shows how to debug the TLV data errors during a file-read operation:

Switch# debug sw-vlan ifs read 4
vlan manager ifs read # 4 errors debugging is on
Switch# 

Related Commands

undebug sw-vlan ifs (same as no debug sw-vlan ifs)

debug sw-vlan notification

To enable the debugging of the messages that trace the activation and deactivation of the ISL VLAN IDs, use the debug sw-vlan notification command. To disable the debugging output, use the no form of this command.

debug sw-vlan notification {accfwdchange | allowedvlancfgchange | fwdchange | linkchange | modechange | pruningcfgchange | statechange}

no debug sw-vlan notification {accfwdchange | allowedvlancfgchange | fwdchange | linkchange | modechange | pruningcfgchange | statechange}

Syntax Description

accfwdchange

Enables the VLAN manager notification of aggregated access interface STP forward changes.

allowedvlancfgchange

Enables the VLAN manager notification of changes to allowed VLAN configuration.

fwdchange

Enables the VLAN manager notification of STP forwarding changes.

linkchange

Enables the VLAN manager notification of interface link state changes.

modechange

Enables the VLAN manager notification of interface mode changes.

pruningcfgchange

Enables the VLAN manager notification of changes to pruning configuration.

statechange

Enables the VLAN manager notification of interface state changes.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to debug the software VLAN interface mode change notifications:

Switch# debug sw-vlan notification modechange
vlan manager port mode change notification debugging is on
Switch# 

Related Commands

undebug sw-vlan notification (same as no debug sw-vlan notification)

debug sw-vlan vtp

To enable the debugging of messages to be generated by the VTP protocol code, use the debug sw-vlan vtp command. To disable the debugging output, use the no form of this command.

debug sw-vlan vtp {events | packets | pruning [packets | xmit] | xmit}

no debug sw-vlan vtp {events | packets | pruning [packets | xmit] | xmit}

Syntax Description

events

Displays the general-purpose logic flow and detailed VTP debugging messages generated by the VTP_LOG_RUNTIME macro in the VTP code.

packets

Displays the contents of all incoming VTP packets that have been passed into the VTP code from the Cisco IOS VTP platform-dependent layer, except for pruning packets.

pruning

Enables the debugging message to be generated by the pruning segment of the VTP protocol code.

packets

(Optional) Displays the contents of all incoming VTP pruning packets that have been passed into the VTP code from the Cisco IOS VTP platform-dependent layer.

xmit

(Optional) Displays the contents of all outgoing VTP packets that the VTP code will request that the Cisco IOS VTP platform-dependent layer to send.

xmit

Displays the contents of all outgoing VTP packets that the VTP code will request that the Cisco IOS VTP platform-dependent layer to send; does not include pruning packets.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

If you do not enter any more parameters after entering pruning, the VTP pruning debugging messages are displayed.

Examples

This example shows how to debug the software VLAN outgoing VTP packets:

Switch# debug sw-vlan vtp xmit
vtp xmit debugging is on
Switch# 

Related Commands

undebug sw-vlan vtp (same as no debug sw-vlan vtp)

debug udld

To enable the debugging of UDLD activity, use the debug udld command. To disable the debugging output, use the no form of this command.

debug udld {events | packets | registries}

no debug udld {events | packets | registries}

Syntax Description

events

Enables the debugging of UDLD process events as they occur.

packets

Enables the debugging of the UDLD process as it receives packets from the packet queue and attempts to transmit packets at the request of the UDLD protocol code.

registries

Enables the debugging of the UDLD process as it processes registry upcalls from the UDLD process-dependent module and other feature modules.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

This command is supported only by the supervisor engine and can be entered only from the Catalyst 4500 series switch console.

Examples

This example shows how to debug the UDLD events:

Switch# debug udld events
UDLD events debugging is on
Switch# 

This example shows how to debug the UDLD packets:

Switch# debug udld packets
UDLD packets debugging is on
Switch# 

This example shows how to debug the UDLD registry events:

Switch# debug udld registries
UDLD registries debugging is on
Switch# 

Related Commands

undebug udld (same as no debug udld)

debug vqpc

To debug the VLAN Query Protocol (VQP), use the debug vqpc command. To disable the debugging output, use the no form of this command.

debug vqpc [all | cli | events | learn | packet]

no debug vqpc [all | cli | events | learn | packet]

Syntax Description

all

(Optional) Debugs all the VQP events.

cli

(Optional) Debugs the VQP command-line interface.

events

(Optional) Debugs the VQP events.

learn

(Optional) Debugs the VQP address learning.

packet

(Optional) Debugs the VQP packets.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(13)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to enable all VQP debugging:

Switch# debug vqpc all
Switch# 

Related Commands

vmps reconfirm (privileged EXEC)

define interface-range

To create a macro of interfaces, use the define interface-range command.

define interface-range macro-name interface-range

Syntax Description

macro-name

Name of the interface range macro; up to 32 characters.

interface-range

List of valid ranges when specifying interfaces; see the "Usage Guidelines" section.


Defaults

This command has no default settings.

Command Modes

Global configuration

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

The macro name is a character string of up to 32 characters.

A macro can contain up to five ranges. An interface range cannot span modules.

When entering the interface-range, use these formats:

interface-type {mod}/{first-interface} - {last-interface}

interface-type {mod}/{first-interface} - {last-interface}

The valid values for interface-type are as follows:

FastEthernet

GigabitEthernet

Vlan vlan_id

Examples

This example shows how to create a multiple-interface macro:

Switch(config)# define interface-range macro1 gigabitethernet 4/1-6, fastethernet 2/1-5
Switch(config)# 

Related Commands

interface range

deny

To deny an ARP packet based on matches against the DHCP bindings, use the deny command. To remove the specified ACEs from the access list, use the no form of this command.

deny {[request] ip {any | host sender-ip | sender-ip sender-ip-mask} mac {any | host sender-mac | sender-mac sender-mac-mask} | response ip {any | host sender-ip | sender-ip sender-ip-mask} [{any | host target-ip | target-ip target-ip-mask}] mac {any | host sender-mac | sender-mac sender-mac-mask} [{any | host target-mac | target-mac target-mac-mask}]} [log]

no deny {[request] ip {any | host sender-ip | sender-ip sender-ip-mask} mac {any | host sender-mac | sender-mac sender-mac-mask} | response ip {any | host sender-ip | sender-ip sender-ip-mask} [{any | host target-ip | target-ip target-ip-mask}] mac {any | host sender-mac | sender-mac sender-mac-mask} [{any | host target-mac | target-mac target-mac-mask}]} [log]

Syntax Description

request

(Optional) Requests a match for the ARP request. When request is not specified, matching is performed against all ARP packets.

ip

Specifies the sender IP address.

any

Specifies that any IP or MAC address will be accepted.

host sender-ip

Specifies that only a specific sender IP address will be accepted.

sender-ip sender-ip-mask

Specifies that a specific range of sender IP addresses will be accepted.

mac

Specifies the sender MAC address.

host sender-mac

Specifies that only a specific sender MAC address will be accepted.

sender-mac sender-mac-mask

Specifies that a specific range of sender MAC addresses will be accepted.

response

Specifies a match for the ARP responses.

ip

Specifies the IP address values for the ARP responses.

host target-ip

(Optional) Specifies that only a specific target IP address will be accepted.

target-ip target-ip-mask

(Optional) Specifies that a specific range of target IP addresses will be accepted.

mac

Specifies the MAC address values for the ARP responses.

host target-mac

(Optional) Specifies that only a specific target MAC address will be accepted.

target-mac target-mac-mask

(Optional) Specifies that a specific range of target MAC addresses will be accepted.

log

(Optional) Logs a packet when it matches the access control entry (ACE).


Defaults

At the end of the ARP access list, there is an implicit deny ip any mac any command.

Command Modes

arp-nacl configuration

Command History

Release
Modification

12.1(19)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

Deny clauses can be added to forward or drop ARP packets based on some matching criteria.

Examples

This example shows a host with a MAC address of 0000.0000.abcd and an IP address of 1.1.1.1. This example shows howto deny both requests and responses from this host:

Switch(config)# arp access-list static-hosts
Switch(config-arp-nacl)# deny ip host 1.1.1.1 mac host 0000.0000.abcd
Switch(config-arp-nacl)# end
Switch# show arp access-list

ARP access list static-hosts
    deny ip host 1.1.1.1 mac host 0000.0000.abcd 
Switch#

Related Commands

arp access-list
ip arp inspection filter vlan
permit

diagnostic monitor action

To direct the action of the switch when it detects a packet memory failure, use the diagnostic monitor action command.

diagnostic monitor action [conservative | normal | aggressive]

Syntax Description

conservative

(Optional) Specifies that the bootup SRAM diagnostics log all failures and remove all affected buffers from the hardware operation. The ongoing SRAM diagnostics will log events, but will take no other action.

normal

(Optional) Specifies that the SRAM diagnostics operate as in conservative mode, except that an ongoing failure resets the supervisor engine; allows for the bootup tests to map out the affected memory.

aggressive

(Optional) Specifies that the SRAM diagnostics operate as in normal mode, except that a bootup failure only logs failures and does not allow the supervisor engine to come online; allows for either a redundant supervisor engine or network-level redundancy to take over.


Defaults

normal mode

Command Modes

Global configuration mode

Command History

Release
Modification

12.2(18)EW

This command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

Use the conservative keyword when you do not want the switch to reboot so that the problem can be fixed.

Use the aggressive keyword when you have redundant supervisor engines, or when network-level redundancy has been provided.

Examples

This example shows how to configure the switch to initiate an RPR switchover when an ongoing failure occurs:

Switch# configure terminal
Switch (config)# diagnostic monitor action normal

Related Commands

show diagnostic result module test 2
show diagnostic result module test 3

diagnostic start

To run the specified diagnostic test, use the diagnostic start command.

diagnostic start {module num} {test test-id} [port num]

Syntax Description

module num

Module number.

test

Specifies a test to run.

test-id

Specifies an identification number for the test to be run; can be the cable diagnostic test-id, or the cable-tdr keyword.

port num

(Optional) Specifies the interface port number.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(25)SG

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to run the specified diagnostic test at the specified slot:

This exec command starts the TDR test on specified interface
Switch# diagnostic start module 1 test cable-tdr port 3
diagnostic start module 1 test cable-tdr port 3
module 1: Running test(s) 5 Run interface level cable diags
module 1: Running test(s) 5 may disrupt normal system operation
Do you want to continue? [no]: yes
yes
Switch#
2d16h: %DIAG-6-TEST_RUNNING: module 1: Running online-diag-tdr{ID=5} ...
2d16h: %DIAG-6-TEST_OK: module 1: online-diag-tdr{ID=5} has completed successfully
 
Switch#

Note The show cable-diagnostic tdr command is used to display the results of a TDR test. The test results will not be available until approximately 1 minute after the test starts. If you type the
show cable-diagnostic tdr command within 1 minute of the test starting, you may see a "TDR test is in progress on interface..." message.


Related Commands

show diagnostic content

dot1x auth-fail max-attempts

To configure the max number of attempts before a port is moved to the auth-fail VLAN, use the
dot1x auth-fail max-attempts command. To return to the default setting, use the no form of this command.

dot1x auth-fail max-attempts max-attempts

no dot1x auth-fail max-attempts max-attempts

Syntax Description

max-attempts

Specifies a maximum number of attempts before a port is moved to the auth-fail VLAN in the range of 1 to 10.


Defaults

Default is 3.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(25)SG

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to configure the maximum number of attempts before the port is moved to the auth-fail VLAN on Fast Ethernet interface 4/3:

Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface fastethernet4/3
Switch(config-if)# dot1x auth-fail max-attempts 5
Switch(config-if)# end
Switch#

Related Commands

dot1x max-reauth-req
show dot1x

dot1x auth-fail vlan

To enable the auth-fail VLAN on a port, use the dot1x auth-fail vlan command. To return to the default setting, use the no form of this command.

dot1x auth-fail vlan vlan-id

no dot1x auth-fail vlan vlan-id

Syntax Description

vlan-id

Specifies a VLAN in the range of 1 to 4094.


Defaults

None

Command Modes

Interface configuration

Command History

Release
Modification

12.2(25)SG

Support for this command was introduced on the Catalyst 4500 series switch.


Examples

This example shows how to configure the auth-fail VLAN on Fast Ethernet interface 4/3:

Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface fastethernet4/3
Switch(config-if)# dot1x auth-fail vlan 40
Switch(config-if)# end
Switch#

Related Commands

dot1x max-reauth-req
show dot1x

dot1x guest-vlan

To enable a guest VLAN on a per-port basis, use the dot1x guest-vlan command. To return to the default setting, use the no form of this command.

dot1x guest-vlan vlan-id

no dot1x guest-vlan vlan-id

Syntax Description

vlan-id

Specifies a VLAN in the range of 1 to 4094.


Defaults

None; the guest VLAN feature is disabled.

Command Modes

Interface configuration

Command History

Release
Modification

12.1(19)EW

Support for this command was introduced on the Catalyst 4500 series switch.

12.2(25)EWA

Support for secondary VLAN as the configured guest VLAN ID was added.


Usage Guidelines

Guest VLANs can be configured only on ports that are statically configured as access ports or private VLAN host ports. Statically configured access ports can be configured with regular VLANs as guest VLANs; statically configured private VLAN host ports can be configured with secondary private VLANs as guest VLANs.

Examples

This example shows how to enable a guest VLAN on Fast Ethernet interface 4/3:

Switch# configure terminal 
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface fastethernet4/3
Switch(config-if)# dot1x port-control auto
Switch(config-if)# dot1x guest-vlan 26
Switch(config-if)# end
Switch(config)# end
Switch#

Related Commands

dot1x max-reauth-req
show dot1x

dot1x guest-vlan supplicant

To place an 802.1X-capable supplicant (host) into a guest VLAN, use the dot1x guest-vlan supplicant global configuration command. To return to the default setting, use the no form of this command.

dot1x quest-vlan supplicant

no dot1x quest-vlan supplicant

Syntax Description

This command has no arguments or keywords.

Defaults

802.1X-capable hosts are not put into a guest VLAN.

Command Modes

Global configuration

Command History

Release
Modification

12.2(25)EWA

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

With Cisco Release 12.2(25) EWA, you can use the dot1x guest-vlan supplicant command to place an 802.1X-capable host into a guest VLAN. Prior to Cisco Release 12.2(25)EWA, you could only place non-802.1X capable hosts into a guest VLAN.

When guest VLAN supplicant behavior is enabled, the Catalyst 4500 series switch does not maintain EAPOL packet history. The switch allows clients that fail 802.1X authentication to access a guest VLAN, whether or not EAPOL packets have been detected on the interface.

Examples

This example shows how to place an 802.1X-capable supplicant (host) into a guest VLAN:

Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# dot1x guest-vlan supplicant
Switch(config)# end
Switch# 

Related Commands

dot1x system-auth-control
show dot1x

dot1x host-mode

Use the dot1x host-mode interface configuration command on the switch stack or on a standalone switch to allow a single host (client) or multiple hosts on an IEEE 802.1x-authorized port. Use the multi-domain keyword to enable multidomain authentication (MDA) on an IEEE 802.1x-authorized port. Use the no form of this command to return to the default setting.

dot1x host-mode {multi-host | single-host}

no dot1x host-mode [multi-host | single-host}

Syntax Description

multi-host

Enable multiple-hosts mode on the switch.

single-host

Enable single-host mode on the switch.


Defaults

The default is single-host mode.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(20)EWA

Support for this command was introduced on the Catalyst 4500 series switch..


Usage Guidelines

Use this command to limit an IEEE 802.1x-enabled port to a single client or to attach multiple clients to an IEEE 802.1x-enabled port. In multiple-hosts mode, only one of the attached hosts needs to be successfully authorized for all hosts to be granted network access. If the port becomes unauthorized (re-authentication fails or an Extensible Authentication Protocol over LAN [EAPOL]-logoff message is received), all attached clients are denied access to the network.

Before entering this command, make sure that the dot1x port-control interface configuration command is set to auto for the specified port.

Examples

This example shows how to enable MDA and to allow both a host and a voice device on the port:

Switch# configure t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface FastEthernet6/1
Switch(config-if)# switchport access vlan 12
Switch(config-if)# switchport mode access
Switch(config-if)# switchport voice vlan 10
Switch(config-if)# dot1x pae authenticator
Switch(config-if)# dot1x port-control auto
Switch(config-if)# dot1x host-mode multi-domain
Switch(config-if)# no shutdown
Switch(config-if)# end
Switch#

You can verify your settings by entering the show dot1x [interface interface-id] privileged EXEC command.

Related Commands

show dot1x

dot1x initialize

To unauthorize an interface before reinitializing 802.1X, use the dot1x initialize command.

dot1x initialize interface

Syntax Description

interface

Number of the interface.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(12c)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

Use this command to initialize state machines and to set up the environment for fresh authentication.

Examples

This example shows how to initialize the 802.1X state machines on an interface:

Switch# dot1x initialize
Switch# 

Related Commands

dot1x initialize
show dot1x

dot1x max-reauth-req

To set the maximum number of times that the switch will retransmit an EAP-Request/Identity frame to the client before restarting the authentication process, use the dot1x max-reauth-req command. To return to the default setting, use the no form of this command.

dot1x max-reauth-req count

no dot1x max-reauth-req

Syntax Description

count

Number of times that the switch retransmits EAP-Request/Identity frames before restarting the authentication process; valid values are from 1 to 10.


Defaults

The switch sends a maximum of two retransmissions.

Command Modes

Interface configuration.

Command History

Release
Modification

12.1(19)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

You should change the default value of this command only to adjust for unusual circumstances such as unreliable links or specific behavioral problems with certain clients and authentication servers. This setting impacts the wait before a non-dot1x-capable client is admitted to the guest VLAN, if one is configured.

You can verify your settings by entering the show dot1x privileged EXEC command.

Examples

This example shows how to set 5 as the number of times that the switch retransmits an EAP-Request/Identity frame before restarting the authentication process:

Switch(config-if)# dot1x max-reauth-req 5
Switch(config-if)#

Related Commands

show dot1x

dot1x max-req

To set the maximum number of times that the switch retransmits an Extensible Authentication Protocol (EAP)-Request frame of types other than EAP-Request/Identity to the client before restarting the authentication process, use the dot1x max-req command. To return to the default setting, use the no form of this command.

dot1x max-req count

no dot1x max-req

Syntax Description

count

Number of times that the switch retransmits EAP-Request frames of types other than EAP-Request/Identity before restarting the authentication process; valid values are from 1 to 10.


Defaults

The switch sends a maximum of two retransmissions.

Command Modes

Interface configuration

Command History

Release
Modification

12.1(12c)EW

Support for this command was introduced on the Catalyst 4500 series switch.

12.1(19)EW

This command was modified to control on EAP-Request/Identity retransmission limits.


Usage Guidelines

You should change the default value of this command only to adjust for unusual circumstances such as unreliable links or specific behavioral problems with certain clients and authentication servers.

You can verify your settings by entering the show dot1x privileged EXEC command.

Examples

This example shows how to set 5 as the number of times that the switch retransmits an EAP-Request frame before restarting the authentication process:

Switch(config-if)# dot1x max-req 5
Switch(config-if)# 

Related Commands

dot1x initialize
dot1x max-reauth-req
show dot1x

dot1x port-control

To enable manual control of the authorization state on a port, use the dot1x port-control command. To return to the default setting, use the no form of this command.

dot1x port-control {auto | force-authorized | force-unauthorized}

no dot1x port-control {auto | force-authorized | force-unauthorized}

Syntax Description

auto

Enables 802.1X authentication on the interface and causes the port to transition to the authorized or unauthorized state based on the 802.1X authentication exchange between the switch and the client.

force-authorized

Disables 802.1X authentication on the interface and causes the port to transition to the authorized state without any authentication exchange required. The port transmits and receives normal traffic without 802.1X-based authentication of the client.

force-unauthorized

Denies all access through the specified interface by forcing the port to transition to the unauthorized state, ignoring all attempts by the client to authenticate. The switch cannot provide authentication services to the client through the interface.


Defaults

The port 802.1X authorization is disabled.

Command Modes

Interface configuration

Command History

Release
Modification

12.1(12c)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

The 802.1X protocol is supported on both the Layer 2 static-access ports and the Layer 3-routed ports.

You can use the auto keyword only if the port is not configured as follows:

Trunk port—If you try to enable 802.1X on a trunk port, an error message appears, and 802.1X is not enabled. If you try to change the mode of an 802.1X-enabled port to trunk, the port mode is not changed.

Dynamic ports—A port in dynamic mode can negotiate with its neighbor to become a trunk port. If you try to enable 802.1X on a dynamic port, an error message appears, and 802.1X is not enabled. If you try to change the mode of an 802.1X-enabled port to dynamic, the port mode is not changed.

EtherChannel port—Before enabling 802.1X on the port, you must first remove it from the EtherChannel. If you try to enable 802.1X on an EtherChannel or on an active port in an EtherChannel, an error message appears, and 802.1X is not enabled. If you enable 802.1X on an inactive port of an EtherChannel, the port does not join the EtherChannel.

Switch Port Analyzer (SPAN) destination port—You can enable 802.1X on a port that is a SPAN destination port; however, 802.1X is disabled until the port is removed as a SPAN destination. You can enable 802.1X on a SPAN source port.

To globally disable 802.1X on the switch, you must disable it on each port. There is no global configuration command for this task.

Examples

This example shows how to enable 802.1X on Gigabit Ethernet 1/1:

Switch(config)# interface gigabitethernet1/1
Switch(config-if)# dot1x port-control auto
Switch# 

You can verify your settings by usingthe show dot1x all or show dot1x interface int commands to show the port-control status. An enabled status indicates that the port-control value is set either to auto or to force-unauthorized.

Related Commands

show dot1x

dot1x re-authenticate

To manually initiate a reauthentication of all 802.1X-enabled ports or the specified 802.1X-enabled port, use the dot1x re-authenticate command.

dot1x re-authenticate [interface interface-id]

Syntax Description

interface interface-id

(Optional) Slot and port number of the interface.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.1(12c)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

You can use this command to reauthenticate a client without waiting for the configured number of seconds between reauthentication attempts (re-authperiod) and automatic reauthentication.

Examples

This example shows how to manually reauthenticate the device connected to Gigabit Ethernet interface 1/1:

Switch# dot1x re-authenticate interface gigabitethernet1/1
Starting reauthentication on gigabitethernet1/1
Switch# 

dot1x re-authentication

To enable the periodic reauthentication of the client, use the dot1x re-authentication command. To return to the default setting, use the no form of this command.

dot1x re-authentication

no dot1x re-authentication

Syntax Description

This command has no arguments or keywords.

Defaults

The periodic reauthentication is disabled.

Command Modes

Interface configuration

Command History

Release
Modification

12.1(12c)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

You configure the amount of time between the periodic reauthentication attempts by using the dot1x timeout re-authperiod global configuration command.

Examples

This example shows how to disable the periodic reauthentication of the client:

Switch(config-if)# no dot1x re-authentication
Switch(config-if)# 

This example shows how to enable the periodic reauthentication and set the number of seconds between the reauthentication attempts to 4000 seconds:

Switch(config-if)# dot1x re-authentication
Switch(config-if)# dot1x timeout re-authperiod 4000
Switch# 

You can verify your settings by entering the show dot1x privileged EXEC command.

Related Commands

dot1x timeout
show dot1x

dot1x system-auth-control

To enable 802.1X authentication on the switch, use the dot1x system-auth-control command. To disable 802.1X authentication on the system, use the no form of this command.

dot1x system-auth-control

no dot1x system-auth-control

Syntax Description

This command has no arguments or keywords.

Defaults

The 802.1X authentication is disabled.

Command Modes

Global configuration

Command History

Release
Modification

12.1(12c)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

You must enable dot1x system-auth-control if you want to use the 802.1X access controls on any port on the switch. You can then use the dot1x port-control auto command on each specific port on which you want the 802.1X access controls to be used.

Examples

This example shows how to enable 802.1X authentication:

Switch(config)# dot1x system-auth-control
Switch(config)# 

Related Commands

dot1x initialize
show dot1x

dot1x timeout

To set the reauthentication timer, use the dot1x timeout command. To return to the default setting, use the no form of this command.

dot1x timeout {reauth-period {seconds | server} | quiet-period seconds | tx-period seconds |
supp-timeout seconds | server-timeout seconds}

no dot1x timeout {reauth-period | quiet-period | tx-period | supp-timeout | server-timeout}

Syntax Description

reauth-period seconds

Number of seconds between reauthentication attempts; valid values are from 1 to 65535. See the "Usage Guidelines" section for more information.

reauth-period server

Number of seconds between reauthentication attempts; valid values are from 1 to 65535 as derived from the Session-Timeout RADIUS attribute. See the "Usage Guidelines" section for more information.

quiet-period seconds

Number of seconds that the switch remains in the quiet state following a failed authentication exchange with the client; valid values are from 0 to 65535 seconds.

tx-period seconds

Number of seconds that the switch waits for a response to an EAP-request/identity frame from the client before retransmitting the request; valid values are from 15 to 65535 seconds.

supp-timeout seconds

Number of seconds that the switch waits for the retransmission of EAP-Request packets; valid values are from 30 to 65535 seconds.

server-timeout seconds

Number of seconds that the switch waits for the retransmission of packets by the back-end authenticator to the authentication server; valid values are from 30 to 65535 seconds.


Defaults

The default settings are as follows:

Reauthentication period is 3600 seconds.

Quiet period is 60 seconds.

Transmission period is 30 seconds.

Supplicant timeout is 30 seconds.

Server timeout is 30 seconds.

Command Modes

Interface configuration

Command History

Release
Modification

12.1(12)EW

Support for this command was introduced on the Catalyst 4500 series switches.

12.2(25)EWA

Support for selecting the reauthentication timer from the "server" was added.


Usage Guidelines

The periodic reauthentication must be enabled before entering the dot1x timeout re-authperiod command. Enter the dot1x re-authentication command to enable periodic reauthentication.

Examples

This example shows how to set 60 as the number of seconds that the switch waits for a response to an EAP-request/identity frame from the client before retransmitting the request:

Switch# configure terminal 
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface fastethernet4/3
Switch(config-if)# dot1x timeout tx-period 60
Switch(config-if)# end
Switch#

You can verify your settings by entering the show dot1x privileged EXEC command.

This example shows how to set up the switch to use a reauthentication timeout derived from a Session-Timeout attribute taken from the RADIUS Access-Accept message received when a host successfully authenticates via 802.1X:

Switch# configure terminal 
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface fastethernet4/3
Switch(config-if)# dot1x timeout reauth-period server
Switch(config-if)# end
Switch#

Related Commands

dot1x initialize
show dot1x

duplex

To configure the duplex operation on an interface, use the duplex command. To return to the default setting, use the no form of this command.

duplex {auto | full | half}

no duplex

Syntax Description

auto

Specifies the autonegotiation operation.

full

Specifies the full-duplex operation.

half

Specifies the half-duplex operation.


Defaults

Half-duplex operation

Command Modes

Interface configuration

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

Table 2-2 lists the supported command options by interface.

Table 2-2 Supported duplex Command Options

Interface Type
Supported Syntax
Default Setting
Guidelines

10/100-Mbps module

duplex [half | full]

half

If the speed is set to auto, you will not be able to set the duplex mode.

If the speed is set to 10 or 100, and you do not configure the duplex setting, the duplex mode is set to half duplex.

100-Mbps fiber modules

duplex [half | full]

half

 

Gigabit Ethernet Interface

Not supported.

Not supported.

Gigabit Ethernet interfaces are set to full duplex.

10/100/1000

duplex [half | full]

 

If the speed is set to auto or 1000, you will not be able to set duplex.

If the speed is set to 10 or 100, and you do not configure the duplex setting, the duplex mode is set to half duplex.


If the transmission speed on a 16-port RJ-45 Gigabit Ethernet port is set to 1000, the duplex mode is set to full. If the transmission speed is changed to 10 or 100, the duplex mode stays at full. You must configure the correct duplex mode on the switch when the transmission speed changes to 10 or 100 from 1000 Mbps.


Note Catalyst 4006 switches cannot automatically negotiate interface speed and duplex mode if either connecting interface is configured to a value other than auto.



Caution Changing the interface speed and duplex mode configuration might shut down and reenable the interface during the reconfiguration.

Table 2-3 describes the system performance for different combinations of the duplex and speed modes. The specified duplex command that is configured with the specified speed command produces the resulting action shown in the table.

Table 2-3 Relationship Between duplex and speed Commands 

duplex Command
speed Command
Resulting System Action

duplex half or duplex full

speed auto

Autonegotiates both speed and duplex modes

duplex half

speed 10

Forces 10 Mbps and half duplex

duplex full

speed 10

Forces 10 Mbps and full duplex

duplex half

speed 100

Forces 100 Mbps and half duplex

duplex full

speed 100

Forces 100 Mbps and full duplex

duplex full

speed 1000

Forces 1000 Mbps and full duplex


Examples

This example shows how to configure the interface for full-duplex operation:

Switch(config-if)# duplex full
Switch(config-if)# 

Related Commands

speed
interface
(refer to Cisco IOS documentation)
show controllers (refer to Cisco IOS documentation)
show interfaces (refer to Cisco IOS documentation)

erase

To erase a file system, use the erase command.

erase {/all [non-default | nvram:] | cat4000_flash | nvram: | startup-config}

Syntax Description

/all nvram:

Erases everything in nvram:.

/all non-default

Erases files and configuration in non-volatile storage including nvram:, bootflash:, cat4000_flash:, and crashinfo: of the local supervisor engine. Resets the Catalyst 4500 series switch to the factory default settings.

Note This command option is intended to work only on a stand-alone supervisor engine.

cat4000_flash:

Erases the VLAN database configuration file.

nvram:

Erases the startup-config and private-config file in nvram.

startup-config:

Erases the startup-config and private-config file in nvram.


Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(25)SG

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines


Caution When you use the erase command to erase a file system, you cannot recover the files in the file system.

In addition to the command options shown above, options with the prefix slave that are used to identify nvram: and flash (like slavenvram: and slavecat4000_flash:) appear in the command help messages on the dual supervisor redundancy switch.

The erase nvram: command replaces the write erase and the erase startup-confg commands. Like these two commands, it erases both the startup-config and the private-config file.

The erase /all nvram: command erases all files in nvram: in addition to startup-config file and private-config file.

The erase cat4000_flash: command erases the VLAN database configuration file.

The erase /all non-default command facilitates the work of a manufacturing facility and repair center. It erases the configuration and states stored in the non-volatile storage and resets the Catalyst 4500 series switch to the factory default settings. The default settings include those mentioned in the IOS library (below) as well as those set by the erase /all non-default command (vtp mode=transparent, and the ROMMON variables: ConfigReg=0x2101, PS1= "rommon ! >" and EnableAutoConfig=1).

Cisco IOS Configuration Fundamentals Configuration Guide, Release 12.2, at this URL:

http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fun_c/index.htm

Cisco IOS Configuration Fundamentals Configuration Command Reference, Release 12.2, at this URL:

http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fun_r/index.htm


Caution The erase /all non-default command can erase IOS images in bootflash:. Ensure that 1) an IOS image can be copied back to the bootflash: (such as, from a accessible TFTP server or a flash card inserted in slot0: (available on most chassis models), or 2) the switch can boot from a image stored in an accessible network server.

Examples

This example shows how to erase the files and configuration in a non-volatile storage and reset the switch to factory default settings:

Switch# erase /all non-default
Switch# 
Erase and format operation will destroy all data in non-volatile storage.  Continue? 
[confirm]
Formatting bootflash: ...
                       
Format of bootflash complete
Erasing nvram:
Erasing cat4000_flash:
Clearing crashinfo:data
Clearing the last power failure timestamp
Clearing all ROMMON variables
Setting default ROMMON variables:
     ConfigReg=0x2101
     PS1=rommon ! >
     EnableAutoConfig=1
Setting vtp mode to transparent
%WARNING! Please reboot the system for the changes to take effect
Switch#
00:01:48: %SYS-7-NV_BLOCK_INIT: Initialized the geometry of nvram
Switch#

This example shows how to erase the contents in nvram.

Switch# erase /all nvram:
Erasing the nvram filesystem will remove all files! Continue? [confirm]
[OK]
Erase of nvram: complete
Switch#
00:38:10: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram
Switch#

This example shows how to erase filesystem cat4000_flash.

Switch# erase cat4000_flash:
Erasing the cat4000_flash filesystem will remove all files! Continue? [confirm]
[OK]
Erase of cat4000_flash:complete
Switch#

Related Commands

boot config (refer to Cisco IOS documentation)
delete (refer to Cisco IOS documentation)
more nvram:startup-config: (refer to Cisco IOS documentation)
show bootvar
undelete
(refer to Cisco IOS documentation)

errdisable detect

To enable error-disable detection, use the errdisable detect command. To disable the error-disable detection feature, use the no form of this command.

errdisable detect cause {all | arp-inspection | dhcp-rate-limit | dtp-flap | gbic-invalid | l2ptguard | link-flap | pagp-flap}

no errdisable detect cause {all | arp-inspection | dhcp-rate-limit | dtp-flap | gbic-invalid | l2ptguard | link-flap | pagp-flap}

Syntax Description

cause

Specifies error-disable detection to detect from a specific cause.

all

Specifies error-disable detection for all error-disable causes.

arp-inspection

Specifies the detection for the ARP inspection error-disable cause.

dhcp-rate-limit

Specifies the detection for the DHCP rate-limit error-disable cause.

dtp-flap

Specifies the detection for the DTP flap error-disable cause.

gbic-invalid

Specifies the detection for the GBIC invalid error-disable cause.

l2ptguard

Specifies the detection for the Layer 2 protocol-tunnel error-disable cause.

link-flap

Specifies the detection for the link flap error-disable cause.

pagp-flap

Specifies the detection for the PAgP flap error-disable cause.


Defaults

All error-disable causes are detected.

Command Modes

Global configuration

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

A cause (dtp-flap, link-flap, pagp-flap) is defined as the reason why the error-disabled state occurred. When a cause is detected on an interface, the interface is placed in error-disabled state (an operational state that is similar to link-down state).

You must enter the shutdown command and then the no shutdown command to recover an interface manually from the error-disable state.

Examples

This example shows how to enable error-disable detection for the link-flap error-disable cause:

Switch(config)# errdisable detect cause link-flap
Switch(config)# 

This example shows how to disable error-disable detection for DAI:

Switch(config)# no errdisable detect cause arp-inspection 
Switch(config)# end
Switch# show errdisable detect
ErrDisable Reason    Detection status
-----------------    ----------------
udld                 Enabled
bpduguard            Enabled
security-violatio    Enabled
channel-misconfig    Disabled
psecure-violation    Enabled
vmps                 Enabled
pagp-flap            Enabled
dtp-flap             Enabled
link-flap            Enabled
l2ptguard            Enabled
gbic-invalid         Enabled
dhcp-rate-limit      Enabled
unicast-flood        Enabled
storm-control        Enabled
ilpower              Enabled
arp-inspection       Disabled
Switch#

Related Commands

show errdisable detect
show interfaces status

errdisable recovery

To configure the recovery mechanism variables, use the errdisable recovery command. To return to the default setting, use the no form of this command.

errdisable recovery [cause {all | arp-inspection | bpduguard | channel-misconfig | dhcp-rate-limit | dtp-flap | gbic-invalid | l2ptguard | link-flap | pagp-flap | pesecure-violation | security-violation | storm-control | udld | unicastflood | vmps} [arp-inspection] [interval {interval}]]

no errdisable recovery [cause {all | arp-inspection | bpduguard | channel-misconfig | dhcp-rate-limit | dtp-flap | gbic-invalid | l2ptguard | link-flap | pagp-flap | pesecure-violation | security-violation | storm-control | udld | unicastflood | vmps} [arp-inspection] [interval {interval}]]

Syntax Description

cause

(Optional) Enables the error-disable recovery to recover from a specific cause.

all

(Optional) Enables the recovery timers for all error-disable causes.

arp-inspection

(Optional) Enables the recovery timer for the ARP inspection cause.

bpduguard

(Optional) Enables the recovery timer for the BPDU guard error-disable cause.

channel-misconfig

(Optional) Enables the recovery timer for the channel-misconfig error-disable cause.

dhcp-rate-limit

(Optional) Enables the recovery timer for the DHCP rate limit error-disable cause.

dtp-flap

(Optional) Enables the recovery timer for the DTP flap error-disable cause.

gbic-invalid

(Optional) Enables the recovery timer for the GBIC invalid error-disable cause.

l2ptguard

(Optional) Enables the recovery timer for the Layer 2 protocol-tunnel error-disable cause.

link-flap

(Optional) Enables the recovery timer for the link flap error-disable cause.

pagp-flap

(Optional) Enables the recovery timer for the PAgP flap error-disable cause.

pesecure-violation

(Optional) Enables the recovery timer for the pesecure violation error-disable cause.

security-violation

(Optional) Enables the automatic recovery of ports disabled due to 802.1X security violations.

storm-control

(Optional) Enables the timer to recover from storm-control error-disable state.

udld

(Optional) Enables the recovery timer for the UDLD error-disable cause.

unicastflood

(Optional) Enables the recovery timer for the unicast flood error-disable cause.

vmps

(Optional) Enables the recovery timer for the VMPS error-disable cause.

arp-inspection

(Optional) Enables the ARP inspection cause and recovery timeout.

interval interval

(Optional) Specifies the time to recover from a specified error-disable cause; valid values are from 30 to 86400 seconds.


Defaults

Error disable recovery is disabled.

The recovery interval is set to 300 seconds.

Command Modes

Configuration

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.

12.1(19)EW

Support for the storm-control feature.


Usage Guidelines

A cause (bpduguard, dtp-flap, link-flap, pagp-flap, udld) is defined as the reason why the error-disabled state occurred. When a cause is detected on an interface, the interface is placed in error-disabled state (an operational state that is similar to the link-down state). If you do not enable error-disable recovery for the cause, the interface stays in the error-disabled state until a shutdown and no shutdown occurs. If you enable recovery for a cause, the interface is brought out of the error-disabled state and allowed to retry operation again once all the causes have timed out.

You must enter the shutdown command and then the no shutdown command to recover an interface manually from error disable.

Examples

This example shows how to enable the recovery timer for the BPDU guard error disable cause:

Switch(config)# errdisable recovery cause bpduguard
Switch(config)# 

This example shows how to set the timer to 300 seconds:

Switch(config)# errdisable recovery interval 300
Switch(config)# 

This example shows how to enable the errdisable recovery for arp-inspection:

Switch(config)# errdisable recovery cause arp-inspection 
Switch(config)# end
Switch# show errdisable recovery 
ErrDisable Reason    Timer Status
-----------------    --------------
udld                 Disabled
bpduguard            Disabled
security-violatio    Disabled
channel-misconfig    Disabled
vmps                 Disabled
pagp-flap            Disabled
dtp-flap             Disabled
link-flap            Disabled
l2ptguard            Disabled
psecure-violation    Disabled
gbic-invalid         Disabled
dhcp-rate-limit      Disabled
unicast-flood        Disabled
storm-control        Disabled
arp-inspection       Enabled

Timer interval: 300 seconds

Interfaces that will be enabled at the next timeout:

Switch#

Related Commands

show errdisable recovery
show interfaces status

flowcontrol

To configure a Gigabit Ethernet interface to send or receive pause frames, use the flowcontrol command. To disable the flow control setting, use the no form of this command.

flowcontrol {receive | send} {off | on | desired}

no flowcontrol {receive | send} {off | on | desired}

Syntax Description

receive

Specifies that the interface processes pause frames.

send

Specifies that the interface sends pause frames.

off

Prevents a local port from receiving and processing pause frames from remote ports or from sending pause frames to remote ports.

on

Enables a local port to receive and process pause frames from remote ports or send pause frames to remote ports.

desired

Obtains predictable results whether a remote port is set to on, off, or desired.


Defaults

The default settings for Gigabit Ethernet interfaces are as follows:

Sending pause frames is desired—Gigabit Ethernet interfaces.

Receiving pause frames is off—Gigabit Ethernet interfaces.

Sending pause frames is on—Oversubscribed Gigabit Ethernet interfaces.

Receiving pause frames is desired—Oversubscribed Gigabit Ethernet interfaces

Table 2-4 shows the default settings for the modules.

Table 2-4 Default Module Settings

Module
Ports
Send

All modules except WS-X4418-GB, WS-X4412-2GB-TX, and WS-X4416-2GB-TX

All ports except for the oversubscribed ports (1-18)

No

WS-X4418-GB

Uplink ports (1-2)

No

WS-X4418-GB

Oversubscribed ports (3-18)

Yes

WS-X4412-2GB-TX

Uplink ports (13-14)

No

WS-X4412-2GB-TX

Oversubscribed ports (1-12)

Yes

WS-X4416-2GB-TX

Uplink ports (17-18)

No


Command Modes

Interface configuration

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

The pause frames are special packets that signal a source to stop sending frames for a specific period of time because the buffers are full.

Table 2-5 describes the guidelines for using the different configurations of the send and receive keywords with the flowcontrol command.

Table 2-5 Keyword Configurations for send and receive 

Configuration
Description

send on

Enables a local port to send pause frames to remote ports. To obtain predictable results, use send on only when remote ports are set to receive on or receive desired.

send off

Prevents a local port from sending pause frames to remote ports. To obtain predictable results, use send off only when remote ports are set to receive off or receive desired.

send desired

Obtains predictable results whether a remote port is set to receive on, receive off, or receive desired.

receive on

Enables a local port to process pause frames that a remote port sends. To obtain predictable results, use receive on only when remote ports are set to send on or send desired.

receive off

Prevents remote ports from sending pause frames to a local port. To obtain predictable results, use send off only when remote ports are set to receive off or receive desired.

receive desired

Obtains predictable results whether a remote port is set to send on, send off, or send desired.


Table 2-6 identifies how the flow control will be forced or negotiated on the Gigabit Ethernet interfaces based on their speed settings.


Note Catalyst 4006 switches support flow control only on the gigabit interfaces.


Table 2-6 Send Capability by Switch Type, Module, and Port 

Interface Type
Configured Speed
Advertised Flow Control

10/100/1000BASE-TX

Speed 1000

Configured flow control always

1000BASE-T

Negotiation always enabled

Configured flow control always negotiated

1000BASE-X

No speed nonegotiation

Configured flow control negotiated

1000BASE-X

Speed nonegotiation

Configured flow control forced


Examples

This example shows how to enable send flow control:

Switch(config-if)# flowcontrol receive on
Switch(config-if)# 

This example shows how to disable send flow control:

Switch(config-if)# flowcontrol send off
Switch(config-if)# 

This example shows how to set receive flow control to desired:

Switch(config-if)# flowcontrol receive desired
Switch(config-if)# 

Related Commands

interface port-channel
interface range
interface vlan
show flowcontrol
show running-config
(refer to Cisco IOS documentation)
speed

hw-module power

To turn the power off on a slot or line module, use the no hw-module power command. To turn the power back on, use the hw-module power command.

hw-module [slot | module] number power

no hw-module [slot | module] number power

Syntax Description

slot

(Optional) Specifies a slot on a chassis.

module

(Optional) Specifies a line module.

number

(Optional) Slot or module number.


Defaults

After a boot up, the power is on.

Command Modes

Global configuration

Command History

Release
Modification

12.1(8a)EW

Support for this command was introduced on the Catalyst 4500 series switch.

12.2(18)EW

Add slot and module keywords.


Examples

This example shows how to shut off power to a module in slot 5:

Switch# no hw-module slot 5 power
Switch# 

Related Commands

clear hw-module slot password

hw-module uplink select

Use the hw-module uplink select command to select the 10-Gigabit Ethernet or Gigabit Ethernet uplinks on the Supervisor Engine V-10GE within the W-C4510R chassis.

hw-module uplink select {tengigabitethernet | gigabitethernet | all}

Syntax Description

tengigabitethernet

(Optional) Specifies the 10-Gigabit Ethernet uplinks.

gigabitethernet

(Optional) Specifies the Gigabit Ethernet uplinks.

all

(Optional) Specifies all uplinks (10-Gigabit Ethernet and Gigabit Ethernet).


Defaults

tengigabitethernet

Command Modes

Global configuration

Command History

Release
Modification

12.2(25)EW

Support for this command was introduced on the Catalyst 4500 series switch.

12.2(25)SG

Support for the all keyword was added.


Usage Guidelines

Supervisor Engine V-10GE and Supervisor Engine II+10GE support 10-Gigabit Ethernet and Gigabit Ethernet uplink ports. On the Supervisor Engine II+10GE, all uplink ports are always available. Similarly, when a Supervisor Engine V-10GE is plugged into a W-C4503, W-4506, or W-4507R chassis, all uplink ports are always available. When a Supervisor Engine V-10GE is plugged into a W-4510R chassis, you can choose to use the 10-Gigabit Ethernet uplink ports, the Gigabit Ethernet uplink ports, or all uplink ports. If you choose to use all uplink ports, then the tenth slot will support only the WS-X4302-GB switching linecard. Be aware that this command takes effect only after a reload (after you have executed the redundancy reload shelf command).

Because the uplink selection is programmed into hardware during initialization, changing the active uplinks requires saving the configuration and reloading the switch. When you are configuring a change to the uplinks, the system responds with a message informing you that the switch must be reloaded and suggesting the appropriate command (depending on redundancy mode) to reload the switch.

If you select the all keyword, ensure that the tenth slot is either empty or has a WS-X4302-GB switching module.

A no form of this command does not exist. To undo the configuration, you must configure the uplinks.

Examples

This example shows how to select the Gigabit Ethernet uplinks:

Switch(config)# hw-module uplink select gigabitethernet
A reload of the active supervisor is required to apply the new configuration. 
Switch(config)# exit
Switch#

Note The Gigabit Ethernet uplinks will be active after the next reload.


This example shows how to select the Gigabit Ethernet uplinks in a redundant system in SSO mode:

Switch(config)# hw-module uplink select gigabitethernet
A 'redundancy reload shelf' or power-cycle of chassis is required to apply the new 
configuration
Switch(config)# exit
Switch#

Note The Gigabit Ethernet uplinks will be active after the next reload of the chassis/shelf. Use the
redundancy reload shelf command to reload the chassis/shelf.


This example shows how to select the Gigabit Ethernet uplinks in a redundant system in RPR mode:

Switch(config)# hw-module uplink select gigabitethernet
A reload of the active supervisor is required to apply the new configuration.
Switch(config)# exit
Switch#

Note The Gigabit Ethernet uplinks will be active on a switchover or reload of the active supervisor engine.


This example shows how to select all the uplinks in a redundant system in SSO mode:

Switch(config)# hw-module uplink select all
Warning: This configuration mode may disable slot10.
A 'redundancy reload shelf' or power-cycle of chassis is required to apply the new 
configuration.
Switch(config)# exit
Switch#

Note If you select the all keyword, only the Drome board will be supported in the tenth slot of the supervisor engine.


Related Commands

show hw-module uplink

instance

To map a VLAN or a set of VLANs to an MST instance, use the instance command. To return the VLANs to the common instance default, use the no form of this command.

instance instance-id {vlans vlan-range}

no instance instance-id

Syntax Description

instance-id

MST instance to which the specified VLANs are mapped; valid values are from 0 to 15.

vlans vlan-range

Specifies the number of the VLANs to be mapped to the specified instance. The number is entered as a single value or a range; valid values are from 1 to 4094.


Defaults

Mapping is disabled.

Command Modes

MST configuration

Command History

Release
Modification

12.1(12c)EW

Support for this command was introduced on the Catalyst 4500 series switch.


Usage Guidelines

The mapping is incremental, not absolute. When you enter a range of VLANs, this range is added or removed to the existing ones.

Any unmapped VLAN is mapped to the CIST instance.

Examples

This example shows how to map a range of VLANs to instance 2:

Switch(config-mst)# instance 2 vlans 1-100
Switch(config-mst)# 

This example shows how to map a VLAN to instance 5:

Switch(config-mst)# instance 5 vlans 1100
Switch(config-mst)# 

This example shows how to move a range of VLANs from instance 2 to the CIST instance:

Switch(config-mst)# no instance 2 vlans 40-60
Switch(config-mst)# 

This example shows how to move all the VLANs mapped to instance 2 back to the CIST instance:

Switch(config-mst)# no instance 2
Switch(config-mst)# 

Related Commands

name
revision
show spanning-tree mst
spanning-tree mst configuration