Catalyst 3750-X and 3560-X Switch Command Reference, Release 12.2(53)SE2
Catalyst 3750-X and 3560-X Switch Cisco IOS Commands - aaa accounting through reserved-only
Downloads: This chapterpdf (PDF - 3.61MB) The complete bookPDF (PDF - 25.07MB) | Feedback

Catalyst 3750-X and 3560-X Switch Cisco IOS Commands

Table Of Contents

Catalyst 3750-X and 3560-X Switch
Cisco IOS Commands

aaa accounting dot1x

aaa authentication dot1x

aaa authorization network

action

archive copy-sw

archive download-sw

archive tar

archive upload-sw

arp access-list

authentication command bounce-port ignore

authentication command disable-port ignore

authentication control-direction

authentication event

authentication event linksec fail action

authentication fallback

authentication host-mode

authentication linksec policy

authentication mac-move permit

authentication open

authentication order

authentication periodic

authentication port-control

authentication priority

authentication timer

authentication violation

auto qos voip

boot auto-copy-sw

boot auto-download-sw

boot config-file

boot enable-break

boot helper

boot helper-config-file

boot manual

boot private-config-file

boot system

cdp forward

channel-group

channel-protocol

cisp enable

class

class-map

clear dot1x

clear eap sessions

clear errdisable interface

clear ip arp inspection log

clear ip arp inspection statistics

clear ip dhcp snooping

clear ipc

clear ipv6 dhcp conflict

clear l2protocol-tunnel counters

clear lacp

clear logging onboard

clear mac address-table

clear mac address-table move update

clear macsec counters interface

clear mka

clear nmsp statistics

clear pagp

clear port-security

clear spanning-tree counters

clear spanning-tree detected-protocols

clear vmps statistics

clear vtp counters

cluster commander-address

cluster discovery hop-count

cluster enable

cluster holdtime

cluster member

cluster outside-interface

cluster run

cluster standby-group

cluster timer

copy logging onboard

confidentiality-offset

define interface-range

delete

deny (ARP access-list configuration)

deny (IPv6 access-list configuration)

deny (MAC access-list configuration)

diagnostic monitor

diagnostic schedule

diagnostic start

dot1x

dot1x auth-fail max-attempts

dot1x auth-fail vlan

dot1x control-direction

dot1x credentials (global configuration)

dot1x critical (global configuration)

dot1x critical (interface configuration)

dot1x default

dot1x fallback

dot1x guest-vlan

dot1x host-mode

dot1x initialize

dot1x mac-auth-bypass

dot1x max-reauth-req

dot1x max-req

dot1x pae

dot1x port-control

dot1x re-authenticate

dot1x reauthentication

dot1x supplicant force-multicast

dot1x test eapol-capable

dot1x test timeout

dot1x timeout

dot1x violation-mode

duplex

errdisable detect cause

errdisable detect cause small-frame

errdisable recovery

errdisable recovery cause small-frame

exception crashinfo

fallback profile

flowcontrol

hw-module

interface port-channel

interface range

interface vlan

ip access-group

ip address

ip admission

ip admission name proxy http

ip arp inspection filter vlan

ip arp inspection limit

ip arp inspection log-buffer

ip arp inspection trust

ip arp inspection validate

ip arp inspection vlan

ip arp inspection vlan logging

ip device tracking maximum

ip dhcp snooping

ip dhcp snooping binding

ip dhcp snooping database

ip dhcp snooping information option

ip dhcp snooping information option allow-untrusted

ip dhcp snooping information option format remote-id

ip dhcp snooping limit rate

ip dhcp snooping trust

ip dhcp snooping verify

ip dhcp snooping vlan

ip dhcp snooping vlan information option format-type circuit-id string

ip igmp filter

ip igmp max-groups

ip igmp profile

ip igmp snooping

ip igmp snooping last-member-query-interval

ip igmp snooping querier

ip igmp snooping report-suppression

ip igmp snooping tcn

ip igmp snooping tcn flood

ip igmp snooping vlan immediate-leave

ip igmp snooping vlan mrouter

ip igmp snooping vlan static

ip snap forwarding

ip source binding

ip ssh

ip sticky-arp (global configuration)

ip sticky-arp (interface configuration)

ip verify source

ipv6 access-list

ipv6 address dhcp

ipv6 dhcp client request vendor

ipv6 dhcp ping packets

ipv6 dhcp pool

ipv6 dhcp server

ipv6 mld snooping

ipv6 mld snooping last-listener-query-count

ipv6 mld snooping last-listener-query-interval

ipv6 mld snooping listener-message-suppression

ipv6 mld snooping robustness-variable

ipv6 mld snooping tcn

ipv6 mld snooping vlan

ipv6 traffic-filter

l2protocol-tunnel

l2protocol-tunnel cos

lacp port-priority

lacp system-priority

link state group

link state track

location (global configuration)

location (interface configuration)

logging event

logging event power-inline-status

logging file

mab request format attribute 32

mac access-group

mac access-list extended

mac address-table aging-time

mac address-table learning vlan

mac address-table move update

mac address-table notification

mac address-table static

mac address-table static drop

mac sec

macro apply

macro auto device

macro auto execute

macro auto file

macro auto global processing

macro auto mac-address-group

macro auto sticky

macro description

macro global

macro global description

match (access-map configuration)

match (class-map configuration)

mdix auto

media-type rj45

mka default-policy

mka policy (global configuration)

mka policy (interface configuration)

mls qos

mls qos aggregate-policer

mls qos cos

mls qos dscp-mutation

mls qos map

mls qos queue-set output buffers

mls qos queue-set output threshold

mls qos rewrite ip dscp

mls qos srr-queue input bandwidth

mls qos srr-queue input buffers

mls qos srr-queue input cos-map

mls qos srr-queue input dscp-map

mls qos srr-queue input priority-queue

mls qos srr-queue input threshold

mls qos srr-queue output cos-map

mls qos srr-queue output dscp-map

mls qos trust

mls qos vlan-based

mode

monitor session

mvr (global configuration)

mvr (interface configuration)

network-policy

network-policy profile (global configuration)

network-policy profile (network-policy configuration)

nmsp

nmsp attachment suppress

nsf

pagp learn-method

pagp port-priority

permit (ARP access-list configuration)

permit (IPv6 access-list configuration)

permit (MAC access-list configuration)

police

police aggregate

policy-map

port-channel load-balance

power inline

power inline consumption

power inline police

power-priority

power rps

power supply

priority-queue

private-vlan

private-vlan mapping

queue-set

radius-server dead-criteria

radius-server host

rcommand

reload

remote command

remote-span

renew ip dhcp snooping database

replay-protection

reserved-only


Catalyst 3750-X and 3560-X Switch
Cisco IOS Commands


aaa accounting dot1x

Use the aaa accounting dot1x global configuration command to enable authentication, authorization, and accounting (AAA) accounting and to create method lists defining specific accounting methods on a per-line or per-interface basis for IEEE 802.1x sessions. Use the no form of this command to disable IEEE 802.1x accounting.

aaa accounting dot1x {name | default} start-stop {broadcast group {name | radius | tacacs+} [group {name | radius | tacacs+} ... ] | group {name | radius | tacacs+} [group {name | radius | tacacs+} ... ]}

no aaa accounting dot1x {name | default}

Syntax Description

name

Name of a server group. This is optional when you enter it after the broadcast group and group keywords.

default

Use the accounting methods that follow as the default list for accounting services.

start-stop

Send a start accounting notice at the beginning of a process and a stop accounting notice at the end of a process. The start accounting record is sent in the background. The requested-user process begins regardless of whether or not the start accounting notice was received by the accounting server.

broadcast

Enable accounting records to be sent to multiple AAA servers and send accounting records to the first server in each group. If the first server is unavailable, the switch uses the list of backup servers to identify the first server.

group

Specify the server group to be used for accounting services. These are valid server group names:

name—Name of a server group.

radius—List of all RADIUS hosts.

tacacs+—List of all TACACS+ hosts.

The group keyword is optional when you enter it after the broadcast group and group keywords. You can enter more than optional group keyword.

radius

(Optional) Enable RADIUS authorization.

tacacs+

(Optional) Enable TACACS+ accounting.


Defaults

AAA accounting is disabled.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

This command requires access to a RADIUS server.

We recommend that you enter the dot1x reauthentication interface configuration command before configuring IEEE 802.1x RADIUS accounting on an interface.

Examples

This example shows how to configure IEEE 802.1x accounting:

Switch(config)# aaa new-model
Switch(config)# aaa accounting dot1x default start-stop group radius

Note The RADIUS authentication server must be properly configured to accept and log update or watchdog packets from the AAA client.


Related Commands

Command
Description

aaa authentication dot1x

Specifies one or more AAA methods for use on interfaces running IEEE 802.1x.

aaa new-model

Enables the AAA access control model. For syntax information, see the Cisco IOS Security Command Reference, Release 12.2 > Authentication, Authorization, and Accounting > Authentication Commands.

dot1x reauthentication

Enables or disables periodic reauthentication.

dot1x timeout reauth-period

Sets the number of seconds between re-authentication attempts.


aaa authentication dot1x

Use the aaa authentication dot1x global configuration command on the switch stack or on a standalone switch to specify the authentication, authorization, and accounting (AAA) method to use on ports complying with the IEEE 802.1x authentication. Use the no form of this command to disable authentication.

aaa authentication dot1x {default} method1

no aaa authentication dot1x {default}

Syntax Description

default

Use the listed authentication method that follows this argument as the default method when a user logs in.

method1

Enter the group radius keywords to use the list of all RADIUS servers for authentication.



Note Though other keywords are visible in the command-line help strings, only the default and group radius keywords are supported.


Defaults

No authentication is performed.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

The method argument identifies the method that the authentication algorithm tries in the given sequence to validate the password provided by the client. The only method that is truly IEEE 802.1x-compliant is the group radius method, in which the client data is validated against a RADIUS authentication server.

If you specify group radius, you must configure the RADIUS server by entering the radius-server host global configuration command.

Use the show running-config privileged EXEC command to display the configured lists of authentication methods.

Examples

This example shows how to enable AAA and how to create an IEEE 802.1x-compliant authentication list. This authentication first tries to contact a RADIUS server. If this action returns an error, the user is not allowed access to the network.

Switch(config)# aaa new-model
Switch(config)# aaa authentication dot1x default group radius

You can verify your settings by entering the show running-config privileged EXEC command.

Related Commands

Command
Description

aaa new-model

Enables the AAA access control model. For syntax information, see the Cisco IOS Security Command Reference, Release 12.2 > Authentication, Authorization, and Accounting > Authentication Commands.

show running-config

Displays the operating configuration. For syntax information, use this link to the Cisco IOS Release 12.2 Command Reference listing page: http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/prod_command_reference_list.html
Select the Cisco IOS Commands Master List, Release 12.2 to navigate to the command.


aaa authorization network

Use the aaa authorization network global configuration command on the switch stack or on a standalone switch to the configure the switch to use user-RADIUS authorization for all network-related service requests, such as IEEE 802.1x per-user access control lists (ACLs) or VLAN assignment. Use the no form of this command to disable RADIUS user authorization.

aaa authorization network default group radius

no aaa authorization network default

Syntax Description

default group radius

Use the list of all RADIUS hosts in the server group as the default authorization list.


Defaults

Authorization is disabled.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Use the aaa authorization network default group radius global configuration command to allow the switch to download IEEE 802.1x authorization parameters from the RADIUS servers in the default authorization list. The authorization parameters are used by features such as per-user ACLs or VLAN assignment to get parameters from the RADIUS servers.

Use the show running-config privileged EXEC command to display the configured lists of authorization methods.

Examples

This example shows how to configure the switch for user RADIUS authorization for all network-related service requests:

Switch(config)# aaa authorization network default group radius

You can verify your settings by entering the show running-config privileged EXEC command.

Related Commands

Command
Description

show running-config

Displays the operating configuration. For syntax information, use this link to the Cisco IOS Release 12.2 Command Reference listing page: http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/prod_command_reference_list.html
Select the Cisco IOS Commands Master List, Release 12.2 to navigate to the command.


action

Use the action access-map configuration command on the switch stack or on a standalone switch to set the action for the VLAN access map entry. Use the no form of this command to return to the default setting.

action {drop | forward}

no action


Note This command is not supported on switches running the LAN base feature set.


Syntax Description

drop

Drop the packet when the specified conditions are matched.

forward

Forward the packet when the specified conditions are matched.


Defaults

The default action is to forward packets.

Command Modes

Access-map configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You enter access-map configuration mode by using the vlan access-map global configuration command.

If the action is drop, you should define the access map, including configuring any access control list (ACL) names in match clauses, before applying the map to a VLAN, or all packets could be dropped.

In access-map configuration mode, use the match access-map configuration command to define the match conditions for a VLAN map. Use the action command to set the action that occurs when a packet matches the conditions.

The drop and forward parameters are not used in the no form of the command.

Examples

This example shows how to identify and apply a VLAN access map vmap4 to VLANs 5 and 6 that causes the VLAN to forward an IP packet if the packet matches the conditions defined in access list al2:

Switch(config)# vlan access-map vmap4
Switch(config-access-map)# match ip address al2
Switch(config-access-map)# action forward
Switch(config-access-map)# exit
Switch(config)# vlan filter vmap4 vlan-list 5-6

You can verify your settings by entering the show vlan access-map privileged EXEC command.

Related Commands

Command
Description

access-list {deny | permit}

Configures a standard numbered ACL. For syntax information, select Cisco IOS IP Command Reference, Volume 1 of 3:Addressing and Services, Release 12.2 > IP Services Commands.

ip access-list

Creates a named access list. For syntax information, select Cisco IOS IP Command Reference, Volume 1 of 3:Addressing and Services, Release 12.2 > IP Services Commands.

mac access-list extended

Creates a named MAC address access list.

match (class-map configuration)

Defines the match conditions for a VLAN map.

show vlan access-map

Displays the VLAN access maps created on the switch.

vlan access-map

Creates a VLAN access map.


archive copy-sw

Use the archive copy-sw privileged EXEC command on the stack master to copy the running image from the flash memory on one stack member to the flash memory on one or more other stack members.

archive copy-sw [/destination-system destination-stack-member-number] [/force-reload] [leave-old-sw] [/no-set-boot] [/overwrite] [/reload] [/safe] source-stack-member-number


Note This command is supported only on Catalyst 3750-X switches.


Syntax Description

/destination-system destination-stack-
member-number

(Optional) The number of the stack member to which to copy the running image. The range is 1 to 9.

/force-reload

(Optional) Unconditionally force a system reload after successfully downloading the software image.

/leave-old-sw

(Optional) Keep the old software version after a successful download.

/no-set-boot

(Optional) Do not alter the setting of the BOOT environment variable to point to the new software image after it is successfully downloaded.

/overwrite

(Optional) Overwrite the software image in flash memory with the downloaded one.

/reload

(Optional) Reload the system after downloading the image unless the configuration has been changed and not been saved.

/safe

(Optional) Keep the current software image; do not delete it to make room for the new software image before the new image is downloaded. The current image is deleted after the download.

source-stack-member-
number

The number of the stack member from which to copy the running image. The range is 1 to 9.


Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

The current software image is not overwritten with the copied image.

Both the software image and HTML files are copied.

The new image is copied to the flash: file system.

The BOOT environment variable is changed to point to the new software image on the flash: file system.

Image names are case sensitive; the image file is provided in tar format.


Note To successfully use the archive copy-sw privileged EXEC command, you must have downloaded from a TFTP server the images for both the stack member switch being added and the stack master. You use the archive download-sw privileged EXEC command to perform the download.


At least one stack member must be running the image that is to be copied to the switch that has incompatible software.

You can copy the image to more than one specific stack member by repeating the /destination-system destination-stack-member-number option in the command for each stack member to be upgraded. If you do not specify the destination-stack-member-number, the default is to copy the running image file to all stack members.

Using the /safe or /leave-old-sw option can cause the new copied image to fail if there is insufficient flash memory. If leaving the software in place would prevent the new image from fitting in flash memory due to space constraints, an error results.

If you used the /leave-old-sw option and did not overwrite the old image when you copied the new one, you can remove the old image by using the delete privileged EXEC command. For more information, see the "delete" section.

Use the /overwrite option to overwrite the image on the flash device with the copied one.

If you specify the command without the /overwrite option, the algorithm verifies that the new image is not the same as the one on the switch flash device or is not running on any stack members. If the images are the same, the copy does not occur. If the images are different, the old image is deleted, and the new one is copied.

After copying a new image, enter the reload privileged EXEC command to begin using the new image, or specify the /reload or /force-reload option in the archive copy-sw command.

You can enter one or more of these options with the source-stack-member-number option:

/destination-system destination-stack-member-number

/force-reload

/leave-old-sw

/no-set-boot

/overwrite

/reload

/safe

If you enter the source-stack-member-number option before one of the previous options, you can enter only the archive copy-sw source-stack-member-number command.

These are examples of how you can enter the archive copy-sw command:

To copy the running image from a stack member to another stack member and to overwrite the software image in the second stack member's flash memory (if it already exists) with the copied one, enter the archive copy-sw /destination destination-stack-member-number /overwrite source-stack-member-number command.

To copy the running image from a stack member to another stack member, keep the current software image, and reload the system after the image copies, enter the archive copy-sw /destination destination-stack-member-number /safe /reload source-stack-member-number command.

Examples

This example shows how to copy the running image from stack member 6 to stack member 8:

Switch# archive copy-sw /destination-system 8 6

This example shows how to copy the running image from stack member 6 to all the other stack members:

Switch# archive copy-sw 6

This example shows how to copy the running image from stack member 5 to stack member 7. If the image being copied already exists on the second stack member's flash memory, it can be overwritten with the copied one. The system reloads after the image is copied:

Switch# archive copy-sw /destination-system 7 /overwrite /force-reload 5

Related Commands

Command
Description

archive download-sw

Downloads a new image from a TFTP server to the switch.

archive tar

Creates a tar file, lists the files in a tar file, or extracts the files from a tar file.

archive upload-sw

Uploads an existing image on the switch to a server.

delete

Deletes a file or directory on the flash memory device.


archive download-sw

Use the archive download-sw privileged EXEC command on the switch stack or on a standalone switch to download a new image from a TFTP server to the switch or switch stack and to overwrite or keep the existing image.

archive download-sw [/allow-feature-upgrade | /destination-system stack-member-number | /directory | /force-reload | /imageonly | /leave-old-sw | /no-set-boot | /no-version-check | /only-system-type system-type | /overwrite | /reload | /safe] source-url1 [source-url2 source-url3 source-url4]

archive download-sw [/allow-feature-upgrade | /destination-system stack-member-number | /directory | /force-reload | /imageonly | /leave-old-sw | /no-set-boot | /no-version-check | /only-system-type system-type | /overwrite | /reload | /safe] /directory source-url1 [source-url2 source-url3 source-url4]

Syntax Description

/allow-feature-upgrade

Allow installation of software images with different feature sets (for example, upgrade from the IP base feature set to the IP services features set).

/destination-system stack-member-number

Specify the specific stack member to be upgraded. The range is 1 to 9.

This keyword is supported only on stacking-capable switches.

/directory

Specify a directory for all of the images.

/force-reload

Unconditionally force a system reload after successfully downloading the software image.

/imageonly

Download only the software image but not the HTML files associated with the embedded device manager. The HTML files for the existing version are deleted only if the existing version is being overwritten or removed.

/leave-old-sw

Keep the old software version after a successful download.

/no-set-boot

Do not alter the setting of the BOOT environment variable to point to the new software image after it is successfully downloaded.

/no-version-check

Download the software image without checking the compatibility of the stack protocol version on the image and on the switch stack.

This keyword is supported only on stacking-capable switches.

/only-system-type system-type

Specify the specific system type to be upgraded. The range is 0 to FFFFFFFF.

This keyword is supported only on stacking-capable switches.

/overwrite

Overwrite the software image in flash memory with the downloaded one.

/reload

Reload the system after successfully downloading the image unless the configuration has been changed and not been saved.

/safe

Keep the current software image; do not delete it to make room for the new software image before the new image is downloaded. The current image is deleted after the download.

source-url1 [sourceurl2 sourceurl3 sourceurl4]

The source URLs for the software images.

On a standalone switch, enter one source URL for the software image that the switch supports.

In a switch stack, you can enter source URLs for the software images that the stack members support as follows:

Up to two source URLs without the /directory keyword.

Up to four source URLS with the /directory keyword.

The image-name.tar is the software image to download and install on the switch.

These options are supported:

Local flash file system syntax on the standalone switch or the stack master:
flash:

Local flash file system syntax on a stack member:
flash member number:

The member number can be from 1 to 9.

FTP syntax: ftp:[[//username[:password]@location]/directory]/image-name.tar

HTTP server syntax:
http://[[username:password]@]{hostname | host-ip}[/directory]/image-name.tar

Secure HTTP server syntax:
https://[[username:password]@]{hostname | host-ip}[/directory]/image-name.tar

Remote Copy Protocol (RCP) syntax: rcp:[[//username@location]/directory]/image-name.tar

Secure Copy Protocol (SCP) syntax for the: scp:[[//username@location]/directory]/image-name.tar

The syntax for the TFTP:
tftp:[[//location]/directory]/image-name.tar


Defaults

The current software image is not overwritten with the downloaded image.

Both the software image and HTML files are downloaded.

The new image is downloaded to the flash: file system.

The BOOT environment variable is changed to point to the new software image on the flash: file system.

Image names are case sensitive; the image file is provided in tar format.

Compatibility of the stack protocol version on the image to be downloaded is checked with the version on the switch stack.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Use the /allow-feature-upgrade option to allow installation of an image with a different feature set, for example, upgrading from the IP base feature set to the IP services feature.

You can use the archive download-sw /directory command to specify a directory only once, followed by a tar file or list of tar files to be downloaded, instead of specifying complete paths with each tar file. For example, in a mixed hardware stack, you can enter archive download-sw /directory tftp://10.1.1.10/ c3750-ipservices-tar.122-35.SE.tar c3750e-universal-tar.122-35.SE2.tar

The /imageonly option removes the HTML files for the existing image if the existing image is being removed or replaced. Only the Cisco IOS image (without the HTML files) is downloaded.

Using the /safe or /leave-old-sw option can cause the new image download to fail if there is insufficient flash memory. If leaving the software in place prevents the new image from fitting in flash memory due to space constraints, an error results.

If you used the /leave-old-sw option and did not overwrite the old image when you downloaded the new one, you can remove the old image by using the delete privileged EXEC command. For more information, see the "delete" section.

Use the /no-version-check option if you want to download an image that has a different stack protocol version than the one existing on the switch stack. You must use this option with the /destination-system option to specify the specific stack member to be upgraded with the image.


Note Use the /no-version-check option with care. All stack members, including the stack master, must have the same stack protocol version to be in the same switch stack. This option allows an image to be downloaded without first confirming the compatibility of its stack protocol version with the version of the switch stack.


You can upgrade more than one specific stack member by repeating the /destination-system option in the command for each stack member to be upgraded.

Use the /overwrite option to overwrite the image on the flash device with the downloaded one.

If you specify the command without the /overwrite option, the download algorithm verifies that the new image is not the same as the one on the switch flash device or is not running on any stack members. If the images are the same, the download does not occur. If the images are different, the old image is deleted, and the new one is downloaded.

After downloading a new image, enter the reload privileged EXEC command to begin using the new image, or specify the /reload or /force-reload option in the archive download-sw command.

Use the /directory option to specify a directory for the images.

Examples

This example shows how to download a new image from a TFTP server at 172.20.129.10 and to overwrite the image on the switch:

Switch# archive download-sw /overwrite tftp://172.20.129.10/test-image.tar 

This example shows how to download only the software image from a TFTP server at 172.20.129.10 to the switch:

Switch# archive download-sw /imageonly tftp://172.20.129.10/test-image.tar 

This example shows how to keep the old software version after a successful download:

Switch# archive download-sw /leave-old-sw tftp://172.20.129.10/test-image.tar 

This example specifies the location of two tar images without having to specify the path each time:

Switch# archive download-sw tftp://10.1.1.10/ 
c3750x-universal-tar.122-53.SE2.tar c3750e-universal-tar.122-35.SE2.tar 

This example specifies the location of three tar images without having to specify the path each time:

Switch# archive download-sw /directory tftp://10.1.1.10/ 
c3750x-universal-tar.122-53.SE2.tar c3750e-universal-tar.122-35.SE2.tar 
c3750-ipbase-tar.122-35.SE.tar 

This example shows how to upgrade stack members 6 and 8:

Switch# archive download-sw /imageonly /destination-system 6 /destination-system 8 
tftp://172.20.129.10/test-image.tar

Related Commands

Command
Description

archive copy-sw

Copies the running image from the flash memory on one stack member to the flash memory on one or more other stack members.

archive tar

Creates a tar file, lists the files in a tar file, or extracts the files from a tar file.

archive upload-sw

Uploads an existing image on the switch to a server.

delete

Deletes a file or directory on the flash memory device.


archive tar

Use the archive tar privileged EXEC command on the switch stack or on a standalone switch to create a tar file, list files in a tar file, or extract the files from a tar file.

archive tar {/create destination-url flash:/file-url} | {/table source-url} | {/xtract source-url flash:/file-url [dir/file...]}

Syntax Description

/create destination-url flash:/file-url

Create a new tar file on the local or network file system.

For destination-url, specify the destination URL alias for the local or network file system and the name of the tar file to create. These options are supported:

The syntax for the local flash filesystem:
flash:

The syntax for the FTP: ftp:[[//username[:password]@location]/directory]/tar-filename.tar

The syntax for an HTTP server:
http://[[username:password]@]{hostname | host-ip}[/directory]/image-name.tar

The syntax for a secure HTTP server:
https://[[username:password]@]{hostname | host-ip}[/directory]/image-name.tar

The syntax for the Remote Copy Protocol (RCP): rcp:[[//username@location]/directory]/tar-filename.tar

The syntax for the TFTP: tftp:[[//location]/directory]/tar-filename.tar

The tar-filename.tar is the tar file to be created.

For flash:/file-url, specify the location on the local flash file system from which the new tar file is created.

An optional list of files or directories within the source directory can be specified to write to the new tar file. If none are specified, all files and directories at this level are written to the newly created tar file.

/table source-url

Display the contents of an existing tar file to the screen.

For source-url, specify the source URL alias for the local or network file system. These options are supported:

The syntax for the local flash file system:
flash:

The syntax for the FTP:
ftp:[[//username[:password]@location]/directory]/tar-filename.tar

The syntax for an HTTP server:
http://[[username:password]@]{hostname | host-ip}[/directory]/image-name.tar

The syntax for a secure HTTP server:
https://[[username:password]@]{hostname | host-ip}[/directory]/image-name.tar

The syntax for the RCP: rcp:[[//username@location]/directory]/tar-filename.tar

The syntax for the TFTP: tftp:[[//location]/directory]/tar-filename.tar

The tar-filename.tar is the tar file to display.

/xtract source-url flash:/file-url [dir/file...]

Extract files from a tar file to the local file system.

For source-url, specify the source URL alias for the local file system. These options are supported:

The syntax for the local flash file system:
flash:

The syntax for the FTP: ftp:[[//username[:password]@location]/directory]/tar-filename.tar

The syntax for an HTTP server:
http://[[username:password]@]{hostname | host-ip}[/directory]/image-name.tar

The syntax for a secure HTTP server:
https://[[username:password]@]{hostname | host-ip}[/directory]/image-name.tar

The syntax for the RCP: rcp:[[//username@location]/directory]/tar-filename.tar

The syntax for the TFTP: tftp:[[//location]/directory]/tar-filename.tar

The tar-filename.tar is the tar file from which to extract.

For flash:/file-url [dir/file...], specify the location on the local flash file system into which the tar file is extracted. Use the dir/file... option to specify an optional list of files or directories within the tar file to be extracted. If none are specified, all files and directories are extracted.


Defaults

There is no default setting.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Filenames and directory names are case sensitive.

Image names are case sensitive.

Examples

This example shows how to create a tar file. The command writes the contents of the new-configs directory on the local flash device to a file named saved.tar on the TFTP server at 172.20.10.30:

Switch# archive tar /create tftp:172.20.10.30/saved.tar flash:/new-configs

This example shows how to display the contents of an image file that is in flash memory. An example of an image file name is c3750x-universal-tar.12-53.SE2. The contents of the tar file appear on the screen:

Switch# archive tar /table flash:image_name.tar
info (219 bytes)

image_name/ (directory)
image_name(610856 bytes)
image_name/info (219 bytes)
info.ver (219 bytes)

This example shows how to display only the html directory and its contents:

Switch# archive tar /table flash:image_name/html
image_name/html/ (directory)
image_name/html/const.htm (556 bytes)
image_name/html/xhome.htm (9373 bytes)
image_name/html/menu.css (1654 bytes)
<output truncated>

This example shows how to extract the contents of a tar file on the TFTP server at 172.20.10.30. This command extracts just the new-configs directory into the root directory on the local flash file system. The remaining files in the saved.tar file are ignored.

Switch# archive tar /xtract tftp://172.20.10.30/saved.tar flash:/ new-configs

Related Commands

Command
Description

archive copy-sw

Copies the running image from the flash memory on one stack member to the flash memory on one or more other stack members.

archive download-sw

Downloads a new image from a TFTP server to the switch.

archive upload-sw

Uploads an existing image on the switch to a server.


archive upload-sw

Use the archive upload-sw privileged EXEC command on the switch stack or on a standalone switch to upload an existing switch image to a server.

archive upload-sw [/source-system-num stack member number | /version version_string] destination-url

Syntax Description

/source-system-num stack member number

Specify the specific stack member containing the image that is to be uploaded.

This keyword is supported only on stacking-capable switches.

/version version_string

(Optional) Specify the specific version string of the image to be uploaded.

destination-url

The destination URL alias for a local or network file system. The image-name.tar is the name of software image to be stored on the server.

These options are supported:

Local flash file system syntax on the standalone switch or the stack master:
flash:

Local flash file system syntax on a stack member:
flash member number:

FTP syntax: ftp:[[//username[:password]@location]/directory]/image-name.tar

HTTP server syntax:
http://[[username:password]@]{hostname | host-ip}[/directory]/image-name.tar

Secure HTTP server syntax:
https://[[username:password]@]{hostname | host-ip}[/directory]/image-name.tar

Remote Copy Protocol (RCP) syntax: rcp:[[//username@location]/directory]/image-name.tar

TFTP syntax:
tftp:[[//location]/directory]/image-name.tar


Defaults

Uploads the currently running image from the flash: file system.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You must specify that the /source-system-num option uses the /version option. The options together upload the specified image, not the running image, of a specific stack member.

Use the upload feature only if the HTML files associated with the embedded device manager have been installed with the existing image.

The files are uploaded in this sequence: the Cisco IOS image, the HTML files, and info. After these files are uploaded, the software creates the tar file.

Image names are case sensitive.

Examples

This example shows how to upload the currently running image on stack member 6 to a TFTP server at 172.20.140.2:

Switch# archive upload-sw /source-system-num 6 tftp://172.20.140.2/test-image.tar 

Related Commands

Command
Description

archive copy-sw

Copies the running image from the flash memory on one stack member to the flash memory on one or more other stack members.

archive download-sw

Downloads a new image to the switch.

archive tar

Creates a tar file, lists the files in a tar file, or extracts the files from a tar file.


arp access-list

Use the arp access-list global configuration command on the switch stack or on a standalone switch to define an Address Resolution Protocol (ARP) access control list (ACL) or to add clauses to the end of a previously defined list. Use the no form of this command to delete the specified ARP access list.

arp access-list acl-name

no arp access-list acl-name

Syntax Description

acl-name

Name of the ACL.


Defaults

No ARP access lists are defined.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

After entering the arp access-list command, you enter ARP access-list configuration mode, and these configuration commands are available:

default: returns a command to its default setting.

deny: specifies packets to reject. For more information, see the "deny (ARP access-list configuration)" section.

exit: exits ARP access-list configuration mode.

no: negates a command or returns to default settings.

permit: specifies packets to forward. For more information, see the "permit (ARP access-list configuration)" section.

Use the permit and deny access-list configuration commands to forward and to drop ARP packets based on the specified matching criteria.

When the ARP ACL is defined, you can apply it to a VLAN by using the ip arp inspection filter vlan global configuration command. ARP packets containing only IP-to-MAC address bindings are compared to the ACL. All other types of packets are bridged in the ingress VLAN without validation. If the ACL permits a packet, the switch forwards it. If the ACL denies a packet because of an explicit deny statement, the switch drops the packet. If the ACL denies a packet because of an implicit deny statement, the switch compares the packet to the list of DHCP bindings (unless the ACL is static, which means that packets are not compared to the bindings).

Examples

This example shows how to define an ARP access list and to permit both ARP requests and ARP responses from a host with an IP address of 1.1.1.1 and a MAC address of 0000.0000.abcd:

Switch(config)# arp access-list static-hosts
Switch(config-arp-nacl)# permit ip host 1.1.1.1 mac host 00001.0000.abcd
Switch(config-arp-nacl)# end

You can verify your settings by entering the show arp access-list privileged EXEC command.

Related Commands

Command
Description

deny (ARP access-list configuration)

Denies an ARP packet based on matches compared against the DHCP bindings.

ip arp inspection filter vlan

Permits ARP requests and responses from a host configured with a static IP address.

permit (ARP access-list configuration)

Permits an ARP packet based on matches compared against the DHCP bindings.

show arp access-list

Displays detailed information about ARP access lists.


authentication command bounce-port ignore

Use the authentication command bounce-port ignore global configuration command on the switch stack or on a standalone switch to allow the switch to ignore a command to temporarily disable a port. Use the no form of this command to return to the default status.

authentication command bounce-port ignore

no authentication command bounce-port ignore

Syntax Description

This command has no arguments or keywords.

Defaults

The switch accepts a RADIUS Change of Authorization (CoA) bounce port command.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

The CoA bounce port command causes a link flap, which triggers a DHCP renegotiation from the host. This is useful when a VLAN change occurs and the endpoint is a device such as a printer, that has no supplicant to detect the change. Use this command to configure the switch to ignore the bounce port command.

Examples

This example shows how to instruct the switch to ignore a CoA bounce port command:

Switch(config)# authentication command bounce-port ignore

Related Commands

Command
Description

authentication command disable-port ignore

Configures the switch to ignore a CoA disable port command.


authentication command disable-port ignore

Use the authentication command disable-port ignore global configuration command on the switch stack or on a standalone switch to allow the switch to ignore a command to disable a port. Use the no form of this command to return to the default status.

authentication command disable-port ignore

no authentication command disable-port ignore

Syntax Description

This command has no arguments or keywords.

Defaults

The switch accepts a RADIUS Change of Authorization (CoA) disable port command.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

The CoA disable port command administratively shuts down a port hosting a session, resulting in session termination. Use this command to configure the switch to ignore this command.

Examples

This example shows how to instruct the switch to ignore a CoA disable port command:

Switch(config)# authentication command disable-port ignore

Related Commands

Command
Description

authentication command bounce-port ignore

Configures the switch to ignore a CoA bounce port command.


authentication control-direction

Use the authentication control-direction interface configuration command to configure the port mode as unidirectional or bidirectional. Use the no form of this command to return to the default setting.

authentication control-direction {both | in}

no authentication control-direction

Syntax Description

both

Enable bidirectional control on port. The port cannot receive packets from or send packets to the host.

in

Enable unidirectional control on port. The port can send packets to the host but cannot receive packets from the host.


Defaults

The port is in bidirectional mode.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Use the both keyword or the no form of this command to return to the default setting (bidirectional mode).

Examples

This example shows how to enable bidirectional mode:

Switch(config-if)# authentication control-direction both

This example shows how to enable unidirectional mode:

Switch(config-if)# authentication control-direction in

You can verify your settings by entering the show authentication privileged EXEC command.

Related Commands

Command
Description

authentication event

Sets the action for specific authentication events.

authentication fallback

Configures a port to use web authentication as a fallback method for clients that do not support IEEE 802.1x authentication.

authentication host-mode

Sets the authorization manager mode on a port.

authentication open

Enables or disables open access on a port.

authentication order

Sets the order of authentication methods used on a port.

authentication periodic

Enable or disables reauthentication on a port.

authentication port-control

Enables manual control of the port authorization state.

authentication priority

Adds an authentication method to the port-priority list.

authentication timer

Configures the timeout and reauthentication parameters for an 802.1x-enabled port.

authentication violation

Configures the violation modes that occur when a new device connects to a port or when a new device connects to a port with the maximum number of devices already connected to that port.

show authentication

Displays information about authentication manager events on the switch.


authentication event

Use the authentication event interface configuration command to set the actions for specific authentication events on the port.

authentication event {[linksec] fail [action [authorize vlan vlan-id | next-method] {| retry {retry count}]} { no-response action authorize vlan vlan-id} {server {alive action reinitialize} | {dead action [authorize | reinitialize vlan vlan-id]}}

Syntax Descriptionno authentication event {fail [action[authorize vlan vlan-id | next-method] {| retry {retry count}]} {no-response action authorize vlan vlan-id} {server {alive action reinitialize} | {dead action [authorize | reinitialize vlan vlan-id]}}

action

Configure the required action for an authentication event.

alive

Configure the authentication, authorization, and accounting (AAA) server alive actions.

authorize

Authorize the port.

dead

Configure the AAA server dead actions.

fail

Configure the failed-authentication parameters.

linksec fail action

See the authentication event linksec fail action command.

next-method

Move to next authentication method.

no-response

Configure the non-responsive host actions.

reinitialize

Reinitialize all authorized clients

retry

Enable retry attempts after a failed authentication.

retry count

Number of retry attempts from 0 to 5.

server

Configure the actions for AAA server events.

vlan

Specify the authentication-fail VLAN from 1 to 4094.

vlan-id

VLAN ID number from 1 to 4094.


Defaults

No event responses are configured on the port.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Use this command with the fail, no-response, or event keywords to configure the switch response for a specific action.

For server-dead events:

When the switch moves to the critical-authentication state, new hosts trying to authenticate are moved to the critical-authentication VLAN (or critical VLAN). This applies whether the port is in single-host, multiple-host, multiauth, or MDA mode. Authenticated hosts remain in the authenticated VLAN, and the reauthentication timers are disabled.

If a client is running Windows XP and the critical port to which the client is connected is in the critical-authentication state, Windows XP might report that the interface is not authenticated.

If the Windows XP client is configured for DHCP and has an IP address from the DHCP server and a critical port receives an EAP-Success message, the DHCP configuration process might not re-initiate.

For no-response events:

If you enable a guest VLAN on an IEEE 802.1x port, the switch assigns clients to a guest VLAN when it does not receive a response to its Extensible Authentication Protocol over LAN (EAPOL) request/identity frame or when EAPOL packets are not sent by the client.

The switch maintains the EAPOL packet history. If another EAPOL packet is detected on the port during the lifetime of the link, the guest VLAN feature is disabled. If the port is already in the guest VLAN state, the port returns to the unauthorized state, and authentication restarts. The EAPOL history is cleared.

If the switch port is moved to the guest VLAN (multi-host mode), multiple non-IEEE 802.1x-capable clients are allowed access . If an IEEE 802.1x-capable client joins the same port on which the guest VLAN is configured, the port is put in the unauthorized state in the RADIUS-configured or user-configured access VLAN, and authentication restarts.

You can configure any active VLAN except a Remote Switched Port Analyzer (RSPAN) VLAN, a primary private VLAN, or a voice VLAN as an IEEE 802.1x guest VLAN. The guest VLAN feature is supported only on access ports. It is not supported on internal VLANs (routed ports) or trunk ports.

When MAC authentication bypass is enabled on an IEEE 802.1x port, the switch can authorize clients based on the client MAC address if IEEE 802.1x authentication times out while waiting for an EAPOL message exchange. After detecting a client on an IEEE 802.1x port, the switch waits for an Ethernet packet from the client. The switch sends the authentication server a RADIUS-access/request frame with a username and password based on the MAC address.

If authorization succeeds, the switch grants the client access to the network.

If authorization fails, the switch assigns the port to the guest VLAN if one is specified.

For more information, see the "Using IEEE 802.1x Authentication with MAC Authentication Bypass" section in the "Configuring IEEE 802.1x Port-Based Authentication" chapter of the software configuration guide.

For authentication-fail events:

If the supplicant fails authentication, the port is moved to a restricted VLAN, and an EAP success message is sent to the supplicant because it i s not notified of the actual authentication failure.

If the EAP success message is not sent, the supplicant tries to authenticate every 60 seconds (the default) by sending an EAP-start message.

Some hosts (for example, devices running Windows XP) cannot implement DHCP until they receive an EAP success message.

The restricted VLAN is supported only in single host mode (the default port mode). When a port is placed in a restricted VLAN, the supplicant's MAC address is added to the MAC address table. Any other MAC address on the port is treated as a security violation.

You cannot configure an internal VLANs for Layer 3 ports as a restricted VLAN. You cannot specify the same VLAN as a restricted VLAN and as a voice VLAN.

Enable re-authentication with restricted VLANs. If re-authentication is disabled, the ports in the restricted VLANs do not receive re-authentication requests if it is disabled.

To start the re-authentication process, the restricted VLAN must receive a link-down event or an Extensible Authentication Protocol (EAP) logoff event from the port. If a host is connected through a hub:

The port might not receive a link-down event when the host is disconnected.

The port might not detect new hosts until the next re-authentication attempt occurs.

When you reconfigure a restricted VLAN as a different type of VLAN, ports in the restricted VLAN are also moved and stay in their currently authorized state.

Examples

This example shows how to configure the authentication event fail command:

Switch(config-if)# authentication event fail action authorize vlan 20

This example shows how to configure a no-response action:

Switch(config-if)# authentication event no-response action authorize vlan 10

This example shows how to configure a server-response action:

Switch(config-if)# authentication event server alive action reinitialize

This example shows how to configure a port to send both new and existing hosts to the critical VLAN when the RADIUS server is unavailable. Use this command for ports in multiple authentication (multiauth) mode or if the voice domain of the port is in MDA mode:

Switch(config-if)# authentication event server dead action authorize vlan 10

This example shows how to configure a port to send both new and existing hosts to the critical VLAN 
when the RADIUS server is unavailable. Use this command for ports in multiple-host or multiauth 
mode:

Switch(config-if)# authentication event server dead action reinitialize vlan 10

You can verify your settings by entering the show authentication privileged EXEC command.

Related Commands

Command
Description

authentication control-direction

Configures the port mode as unidirectional or bidirectional.

authentication fallback

Configures a port to use web authentication as a fallback method for clients that do not support IEEE 802.1x authentication

authentication host-mode

Sets the authorization manager mode on a port.

authentication open

Enables or disable open access on a port.

authentication order

Sets the order of authentication methods used on a port.

authentication periodic

Enables or disables reauthentication on a port

authentication port-control

Enables manual control of the port authorization state.

authentication priority

Adds an authentication method to the port-priority list.

authentication timer

Configures the timeout and reauthentication parameters for an 802.1x-enabled port.

authentication violation

Configures the violation modes that occur when a new device connects to a port or when a new device connects to a port after the maximum number of devices are connected to that port.

show authentication

Displays information about authentication manager events on the switch.


authentication event linksec fail action

To configure the required action for a link-security authentications failure, use the authentication event linksec fail action interface configuration command. To disable the configured fail action, use the no form of this command.

authentication event linksec fail action {authorize vlan vlan-id | next-method}

no authentication event linksec fail action

Syntax Description

authorize vlan vlan-id

Authorizes the port and configures a linksec-fail VLAN ID to use if the link-security authentication fails.

next-method

Moves to the next authentication method. The order of authentication methods is specified by the authentication order command.


Defaults

The default is to take no action when link-security authentication fails.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

When link-security authentication fails because of unrecognized user credentials, this command specifies that the switch authorizes a restricted VLAN on the port.

Examples

This example configures the interface so that the port is assigned to a restricted VLAN 40 after a failed authentication attempt:

Switch(config)# interface gigabitethernet1/0/3 
Switch(config-if)# authentication event linksec fail action authorize vlan 40 
Switch(config-if)# end 

You can verify your setting by entering the show authentication sessions privileged EXEC command.

Related Commands

Command
Description

show authentication sessions

Displays information about authentication events on the switch.


authentication fallback

Use the authentication fallback interface configuration command to configure a port to use web authentication as a fallback method for clients that do not support IEEE 802.1x authentication. To return to the default setting, use the no form of this command.

authentication fallback name

no authentication fallback name

Syntax Description

name

Specify a web authentication fallback profile.


Defaults

No fallback is enabled.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You must enter the authentication port-control auto interface configuration command before configuring a fallback method.

You can only configure web authentication as a fallback method to 802.1x or MAB, so one or both of these authentication methods should be configured for the fallback to enable.

Examples

This example shows how to specify a fallback profile on a port:

Switch(config-if)# authentication fallback profile1

You can verify your settings by entering the show authentication privileged EXEC command.

Related Commands

Command
Description

authentication control-direction

Configures the port mode as unidirectional or bidirectional.

authentication event

Sets the action for specific authentication events.

authentication host-mode

Sets the authorization manager mode on a port.

authentication open

Enables or disable open access on a port.

authentication order

Sets the order of authentication methods used on a port.

authentication periodic

Enables or disables reauthentication on a port.

authentication port-control

Enables manual control of the port authorization state.

authentication priority

Adds an authentication method to the port-priority list.

authentication timer

Configures the timeout and reauthentication parameters for an 802.1x-enabled port.

authentication violation

Configures the violation modes that occur when a new device connects to a port or when a new device connects to a port after the maximum number of devices are connected to that port.

show authentication

Displays information about authentication manager events on the switch.


authentication host-mode

Use the authentication host-mode interface configuration command to set the authorization manager mode on a port.

authentication host-mode [multi-auth | multi-domain | multi-host | single-host]

no authentication host-mode [multi-auth | multi-domain | multi-host | single-host]]

Syntax Description

multi-auth

Enable multiple-authorization mode (multiauth mode) on the port.

multi-domain

Enable multiple-domain mode on the port.

multi-host

Enable multiple-host mode on the port.

single-host

Enable single-host mode on the port.


Defaults

Single host mode is enabled.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Single-host mode should be configured if only one data host is connected. Do not connect a voice device to authenticate on a single-host port. Voice device authorization fails if no voice VLAN is configured on the port.

Multi-domain mode should be configured if data host is connected through an IP Phone to the port. Multi-domain mode should be configured if the voice device needs to be authenticated.

Multi-auth mode should be configured to allow up to eight devices behind a hub to obtain secured port access through individual authentication. Only one voice device can be authenticated in this mode if a voice VLAN is configured.

Multi-host mode also offers port access for multiple hosts behind a hub, but multi-host mode gives unrestricted port access to the devices after the first user gets authenticated.

Examples

This example shows how to enable multiauth mode on a port:

Switch(config-if)# authentication host-mode multi-auth

This example shows how to enable multi-domain mode on a port:

Switch(config-if)# authentication host-mode multi-domain

This example shows how to enable multi-host mode on a port:

Switch(config-if)# authentication host-mode multi-host

This example shows how to enable single-host mode on a port:

Switch(config-if)# authentication host-mode single-host

You can verify your settings by entering the show authentication privileged EXEC command.

Related Commands

Command
Description

authentication control-direction

Configures the port mode as unidirectional or bidirectional.

authentication event

Sets the action for specific authentication events.

authentication fallback

Configures a port to use web authentication as a fallback method for clients that do not support IEEE 802.1x authentication

authentication open

Enables or disable open access on a port.

authentication order

Sets the order of authentication methods used on a port.

authentication periodic

Enables or disable reauthentication on a port.

authentication port-control

Enables manual control of the port authorization state.

authentication priority

Adds an authentication method to the port-priority list.

authentication timer

Configures the timeout and reauthentication parameters for an 802.1x-enabled port.

authentication violation

Configures the violation modes that occur when a new device connects to a port or when a new device connects to a port after the maximum number of devices are connected to that port.

show authentication

Displays information about authentication manager events on the switch.


authentication linksec policy

To set the static selection of a link-security policy, use the authentication linksec policy interface configuration command. To return to the default state, use the no form of this command.

authentication linksec policy {must-not-secure | must-secure | should-secure}

no authentication linksec policy

Syntax Description

must-not-secure

Establishes the host session without Media Access Control Security (MACsec). Never secures the sessions.

must-secure

Secures the session with MACsec. Always secures the sessions.

should-secure

Optionally secures the session with MACsec.


Defaults

The default is to support a link security policy of should secure.

Command Modes

MKA policy configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

The linksec policy might change after a successful reauthentication started by a local timer or a change of authorization (CoA) reauthenticate command. If the policy changes from must-not-secure to must-secure after a reauthentication, the system attempts to secure the session. If the MACsec key does not renegotiate a MACsec connection after a reauthentication, the session is terminated, and all local states are removed.

A per-user policy received after authentication overrides the interface configuration policy.

Examples

This example configures the interface to always secure MACsec sessions:

Switch(config)# interface gigabitethernet1/0/3 
Switch(config-if)# authentication linksec policy must-secure
Switch(config-if)# end 

You can verify your setting by entering the show authentication sessions privileged EXEC command.

Related Commands

Command
Description

show authentication sessions

Displays information about authentication events on the switch.


authentication mac-move permit

Use the authentication mac-move permit global configuration command to enable MAC move on a switch. Use the no form of this command to return to the default setting.

authentication mac-move permit

no authentication mac-move permit

Syntax Description

This command has no arguments or keywords.

Defaults

MAC move is enabled.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

The command enables authenticated hosts to move between 802.1x-enabled ports on a switch. For example, if there is a device between an authenticated host and port, and that host moves to another port, the authentication session is deleted from the first port, and the host is reauthenticated on the new port.

If MAC move is disabled, and an authenticated host moves to another port, it is not reauthenticated, and a violation error occurs.

MAC move is not supported on port-security enabled 802.1x ports. If MAC move is globally configured on the switch and a port security-enabled host moves to an 802.1x-enabled port, a violation error occurs.

Examples

This example shows how to enable MAC move on a switch:

Switch(config)# authentication mac-move permit

Related Commands

Command
Description

authentication event

Sets the action for specific authentication events.

authentication fallback

Configures a port to use web authentication as a fallback method for clients that do not support IEEE 802.1x authentication.

authentication host-mode

Sets the authorization manager mode on a port.

authentication open

Enables or disables open access on a port.

authentication order

Sets the order of authentication methods used on a port.

authentication periodic

Enable or disables reauthentication on a port.

authentication port-control

Enables manual control of the port authorization state.

authentication priority

Adds an authentication method to the port-priority list.

authentication timer

Configures the timeout and reauthentication parameters for an 802.1x-enabled port.

authentication violation

Configures the violation modes that occur when a new device connects to a port or when a new device connects to a port with the maximum number of devices already connected to that port.

show authentication

Displays information about authentication manager events on the switch.


authentication open

Use the authentication open interface configuration command to enable or disable open access on a port. Use the no form of this command to disable open access.

authentication open

no authentication open

Defaults

Open access is disabled.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Open authentication must be enabled if a device requires network access before it is authenticated.

A port ACL should be used to restrict host access when open authentication is enabled.

Examples

This example shows how to enable open access on a port:

Switch(config-if)# authentication open

This example shows how to set the port to disable open access on a port:

Switch(config-if)# no authentication open

Related Commands

Command
Description

authentication control-direction

Configures the port mode as unidirectional or bidirectional.

authentication event

Sets the action for specific authentication events.

authentication fallback

Configures a port to use web authentication as a fallback method for clients that do not support IEEE 802.1x authentication.

authentication host-mode

Sets the authorization manager mode on a port.

authentication order

Sets the order of authentication methods used on a port.

authentication periodic

Enables or disables reauthentication on a port.

authentication port-control

Enables manual control of the port authorization state.

authentication priority

Adds an authentication method to the port-priority list.

authentication timer

Configures the timeout and reauthentication parameters for an 802.1x-enabled port.

authentication violation

Configures the violation modes that occur when a new device connects to a port or when a new device connects to a port after the maximum number of devices are connected to that port.

show authentication

Displays information about authentication manager events on the switch.


authentication order

Use the authentication order interface configuration command to set the order of authentication methods used on a port.

authentication order [dot1x | mab] {webauth}

no authentication order

Syntax Description

dot1x

Add 802.1x to the order of authentication methods.

mab

Add MAC authentication bypass (MAB) to the order of authentication methods.

webauth

Add web authentication to the order of authentication methods.


Command Default

The default authentication order is dot1x followed by mab and webauth.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Ordering sets the order of methods that the switch attempts when trying to authenticate a new device connected to a port. If one method in the list is unsuccessful, the next method is attempted.

Each method can only be entered once. Flexible ordering is only possible between 802.1x and MAB.

Web authentication can be configured as either a standalone method or as the last method in the order after either 802.1x or MAB. Web authentication should be configured only as fallback to dot1x or mab.

Examples

This example shows how to add 802.1x as the first authentication method, MAB as the second method, and web authentication as the third method:

Switch(config-if)# authentication order dotx mab webauth

This example shows how to add MAC authentication Bypass (MAB) as the first authentication method and web authentication as the second authentication method:

Switch(config-if)# authentication order mab webauth

You can verify your settings by entering the show authentication privileged EXEC command.

Related Commands

Command
Description

authentication control-direction

Configures the port mode as unidirectional or bidirectional.

authentication event

Sets the action for specific authentication events.

authentication fallback

Configures a port to use web authentication as a fallback method for clients that do not support IEEE 802.1x authentication.

authentication host-mode

Sets the authorization manager mode on a port.

authentication open

Enables or disables open access on a port.

authentication periodic

Enables or disables reauthentication on a port.

authentication port-control

Enables manual control of the port authorization state.

authentication priority

Adds an authentication method to the port-priority list.

authentication timer

Configures the timeout and reauthentication parameters for an 802.1x-enabled port.

authentication violation

Configures the violation modes that occur when a new device connects to a port or when a new device connects to a port after the maximum number of devices are connected to that port.

mab

Enables MAC authentication bypass on a port.

mab eap

Configures a port to use Extensible Authentication Protocol (EAP).

show authentication

Displays information about authentication manager events on the switch.


authentication periodic

Use the authentication periodic interface configuration command to enable or disable reauthentication on a port. Enter the no form of this command to disable reauthentication.

authentication periodic

no authentication periodic

Command Default

Reauthentication is disabled.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You configure the amount of time between periodic re-authentication attempts by using the authentication timer reauthentication interface configuration command.

Examples

This example shows how to enable periodic reauthentication on a port:

Switch(config-if)# authentication periodic

This example shows how to disable periodic reauthentication on a port:

Switch(config-if)# no authentication periodic

You can verify your settings by entering the show authentication privileged EXEC command.

Related Commands

Command
Description

authentication control-direction

Configures the port mode as unidirectional or bidirectional.

authentication event

Sets the action for specific authentication events.

authentication fallback

Configures a port to use web authentication as a fallback method for clients that do not support IEEE 802.1x authentication.

authentication host-mode

Sets the authorization manager mode on a port.

authentication open

Enables or disable open access on a port.

authentication order

Sets the order of authentication methods used on a port.

authentication port-control

Enables manual control of the port authorization state.

authentication priority

Adds an authentication method to the port-priority list.

authentication timer

Configures the timeout and reauthentication parameters for an 802.1x-enabled port.

authentication violation

Configures the violation modes that occur when a new device connects to a port or when a new device connects to a port after the maximum number of devices are connected to that port.

show authentication

Displays information about authentication manager events on the switch.


authentication port-control

Use the authentication port-control interface configuration command to enable manual control of the port authorization state. Use the no form of this command to return to the default setting.

authentication port-control {auto | force-authorized | force-un authorized}

no authentication port-control {auto | force-authorized | force-un authorized}

Syntax Description

auto

Enable authentication on the port. The port changes to the authorized or unauthorized state based, on the authentication exchange between the switch and the client.

force-authorized

Disable authentication on the port. The port changes to the authorized state without an authentication exchange. The port sends and receives normal traffic without authentication of the client.

force-un authorized

Deny all access the port. The port changes to the unauthorized state, ignoring all attempts by the client to authenticate. The switch cannot provide authentication services to the client through the port.


Defaults

The default setting is force-authorized.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Use the auto keyword only on one of these port types:

Trunk port—If you try to enable authentication on a trunk port, an error message appears, and is not enabled. If you try to change the mode of an port to trunk, an error message appears, and the port mode is not changed.

Dynamic ports—A dynamic port can negotiate with its neighbor to become a trunk port. If you try to enable authentication on a dynamic port, an error message appears, and authentication is not enabled. If you try to change the mode of an port to dynamic, an error message appears, and the port mode does not change.

Dynamic-access ports—If you try to enable authentication on a dynamic-access (VLAN Query Protocol [VQP]) port, an error message appears, and authentication is not enabled. If you try to change an port to dynamic VLAN, an error message appears, and the VLAN configuration does not change.

EtherChannel port—Do not configure a port that is an active or a not-yet-active member of an EtherChannel as an port. If you try to enable authentication on an EtherChannel port, an error message appears, and authentication is not enabled.

Switched Port Analyzer (SPAN) and Remote SPAN (RSPAN) destination ports—You can enable authentication on a port that is a SPAN or RSPAN destination port. However, authentication is disabled until the port is removed as a SPAN or RSPAN destination. You can enable authentication on a SPAN or RSPAN source port.

To globally disable authentication on the switch, use the no dot1x system-auth-control global configuration command. To disable authentication on a specific port or to return to the default setting, use the no authentication port-control interface configuration command.

Examples

This example shows how to set the port state to automatic:

Switch(config-if)# authentication port-control auto

This example shows how to set the port state to the force- authorized state:

Switch(config-if)# authentication port-control force-authorized

This example shows how to set the port state to the force-unauthorized state:

Switch(config-if)# authentication port-control force-unauthorized

You can verify your settings by entering the show authentication privileged EXEC command.

Related Commands

Command
Description

authentication control-direction

Configures the port mode as unidirectional or bidirectional.

authentication event

Sets the action for specific authentication events.

authentication fallback

Configures a port to use web authentication as a fallback method for clients that do not support IEEE 802.1x authentication.

authentication host-mode

Sets the authorization manager mode on a port.

authentication open

Enables or disables open access on a port.

authentication order

Sets the order of the authentication methods used on a port.

authentication periodic

Enables or disable reauthentication on a port.

authentication priority

Adds an authentication method to the port-priority list.

authentication timer

Configures the timeout and reauthentication parameters for an 802.1x-enabled port.

authentication violation

Configures the violation modes that occur when a new device connects to a port or when a new device connects to a port after the maximum number of devices are connected to that port.

show authentication

Displays information about authentication manager events on the switch.


authentication priority

Use the authentication priority interface configuration command to add an authentication method to the port-priority list.

auth priority [dot1x | mab] {webauth}

no auth priority [dot1x | mab] {webauth}

Syntax Description

dot1x

Add 802.1x to the order of authentication methods.

mab

Add MAC authentication bypass (MAB) to the order of authentication methods.

webauth

Add web authentication to the order of authentication methods.


Command Default

The default priority is 802.1x authentication, followed by MAC authentication bypass and web authentication.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Ordering sets the order of methods that the switch attempts when trying to authenticate a new device is connected to a port.

When configuring multiple fallback methods on a port, set web authentication (webauth) last.

Assigning priorities to different authentication methods allows a higher-priority method to interrupt an in-progress authentation method with a lower priority.


Note If a client is already authenticated, it might be reauthenticated if an interruption from a higher-priority method occurs.


The default priority of an authentication method is equivalent to its position in execution-list order: 802.1x authentication, MAC authentication bypass, and web authentication. Use the dot1x, mab, and webauth keywords to change this default order.

Examples

This example shows how to set 802.1x as the first authentication method and web authentication as the second authentication method:

Switch(config-if)# authentication priority dotx webauth

This example shows how to set MAC authentication Bypass (MAB) as the first authentication method and web authentication as the second authentication method:

Switch(config-if)# authentication priority mab webauth

You can verify your settings by entering the show authentication privileged EXEC command.

Related Commands

Command
Description

authentication control-direction

Configures the port mode as unidirectional or bidirectional.

authentication event

Sets the action for specific authentication events.

authentication fallback

Configures a port to use web authentication as a fallback method for clients that do not support IEEE 802.1x authentication.

authentication host-mode

Sets the authorization manager mode on a port.

authentication open

Enables or disables open access on a port.

authentication order

Sets the order of authentication methods used on a port.

authentication periodic

Enables or disables reauthentication on a port.

authentication port-control

Enables manual control of the port authorization state.

authentication timer

Configures the timeout and reauthentication parameters for an 802.1x-enabled port.

authentication violation

Configures the violation modes that occur when a new device connects to a port or when a new device connects to a port after the maximum number of devices are connected to that port.

mab

Enables MAC authentication bypass on a port.

mab eap

Configures a port to use Extensible Authentication Protocol (EAP).

show authentication

Displays information about authentication manager events on the switch.


authentication timer

Use the authentication timer interface configuration command to configure the timeout and reauthentication parameters for an 802.1x-enabled port.

authentication timer {{[inactivity | reauthenticate] [server | am]} {restart value}}

no authentication timer {{[inactivity | reauthenticate] [server | am]} {restart value}}

Syntax Description

inactivity

Interval in seconds after which the client is unauthorized if there is no activity.

reauthenticate

Time in seconds after which an automatic re-authentication attempt starts.

server

Interval in seconds after which an attempt is made to authenticate an unauthorized port.

restart

Interval in seconds after which an attempt is made to authenticate an unauthorized port.

value

Enter a value between 1 and 65535 (in seconds).


Defaults

The inactivity, server, and restart keywords are set to off. The reauthenticate keyword is set to one hour.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

If a timeout value is not configured, an 802.1x session stays authorized indefinitely. No other host can use the port, and the connected host cannot move to another port on the same switch.

Examples

This example shows how to set the authentication inactivity timer to 60 seconds:

Switch(config-if)# authentication timer inactivity 60

This example shows how to set the reauthentication timer to 120 seconds:

Switch(config-if)# authentication timer restart 120

You can verify your settings by entering the show authentication privileged EXEC command.

Related Commands

Command
Description

authentication control-direction

Configures the port mode as unidirectional or bidirectional.

authentication event

Sets the action for specific authentication events.

authentication fallback

Configures a port to use web authentication as a fallback method for clients that do not support IEEE 802.1x authentication.

authentication host-mode

Sets the authorization manager mode on a port.

authentication open

Enables or disables open access on a port.

authentication order

Sets the order of authentication methods used on a port.

authentication periodic

Enables or disables reauthentication on a port.

authentication port-control

Enables manual control of the port authorization state.

authentication priority

Adds an authentication method to the port-priority list.

authentication violation

Configures the violation modes that occur when a new device connects to a port or when a new device connects to a port after the maximum number of devices are connected to that port.

show authentication

Displays information about authentication manager events on the switch.


authentication violation

Use the authentication violation interface configuration command to configure the violation modes that occur when a new device connects to a port or when a new device connects to a port after the maximum number of devices are connected to that port.

authentication violation {protect | restrict | shutdown}

no authentication violation {protect | restrict | shutdown}

Syntax Description

protect

Unexpected incoming MAC addresses are dropped. No syslog errors are generated.

restrict

Generates a syslog error when a violation error occurs.

shutdown

Error disables the port or the virtual port on which an unexpected MAC address occurs.


Defaults

By default authentication violation shutdown mode is enabled.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Examples

This example shows how to configure an IEEE 802.1x-enabled port as error disabled and to shut down when a new device connects it:

Switch(config-if)# authentication violation shutdown

This example shows how to configure an IEEE 802.1x-enabled port to generate a system error message and to change the port to restricted mode when a new device connects to it:

Switch(config-if)# authentication violation restrict

This example shows how to configure an IEEE 802.1x-enabled port to ignore a new device when it connects to the port:

Switch(config-if)# authentication violation protect

You can verify your settings by entering the show authentication privileged EXEC command.

Related Commands

Command
Description

authentication control-direction

Configures the port mode as unidirectional or bidirectional.

authentication event

Sets the action for specific authentication events.

authentication fallback

Configures a port to use web authentication as a fallback method for clients that do not support IEEE 802.1x authentication.

authentication host-mode

Sets the authorization manager mode on a port.

authentication open

Enables or disables open access on a port.

authentication order

Sets the order of authentication methods used on a port.

authentication periodic

Enables or disables reauthentication on a port.

authentication port-control

Enables manual control of the port authorization state.

authentication priority

Adds an authentication method to the port-priority list.

authentication timer

Configures the timeout and reauthentication parameters for an 802.1x-enabled port.

show authentication

Displays information about authentication manager events on the switch.


auto qos voip

Use the auto qos voip interface configuration command on the switch stack or on a standalone switch to automatically configure quality of service (QoS) for voice over IP (VoIP) within a QoS domain. Use the no form of this command to return to the default setting.

auto qos voip {cisco-phone | cisco-softphone | trust}

no auto qos voip [cisco-phone | cisco-softphone | trust]

Syntax Description

cisco-phone

Identify this port as connected to a Cisco IP Phone, and automatically configure QoS for VoIP. The QoS labels of incoming packets are trusted only when the telephone is detected.

cisco-softphone

Identify this port as connected to a device running the Cisco SoftPhone, and automatically configure QoS for VoIP.

trust

Identify this port as connected to a trusted switch or router, and automatically configure QoS for VoIP. The QoS labels of incoming packets are trusted. For nonrouted ports, the CoS value of the incoming packet is trusted. For routed ports, the DSCP value of the incoming packet is trusted.


Defaults

Auto-QoS is disabled on the port.

When auto-QoS is enabled, it uses the ingress packet label to categorize traffic, to assign packet labels, and to configure the ingress and egress queues as shown in Table 2-1.

Table 2-1 Traffic Types, Packet Labels, and Queues

 
VoIP Data Traffic
VoIP Control
Traffic
Routing Protocol Traffic
STP 1 BPDU 2 Traffic
Real-Time Video Traffic
All Other Traffic

DSCP3

46

24, 26

48

56

34

-

CoS4

5

3

6

7

3

-

CoS-to-ingress queue map

2, 3, 4, 5, 6, 7 (queue 2)

0, 1 (queue 1)

CoS-to-egress queue map

5 (queue 1)

3, 6, 7 (queue 2)

4 (queue 3)

2
(queue 3)

0, 1 (queue 4)

1 STP = Spanning Tree Protocol

2 BPDU = bridge protocol data unit

3 DSCP = Differentiated Services Code Point

4 CoS = class of service


Table 2-2 shows the generated auto-QoS configuration for the ingress queues.

Table 2-2 Auto-QoS Configuration for the Ingress Queues

Ingress Queue
Queue Number
CoS-to-Queue Map
Queue Weight (Bandwidth)
Queue (Buffer) Size

SRR1 shared

1

0, 1

81 percent

67 percent

Priority

2

2, 3, 4, 5, 6, 7

19 percent

33 percent

1 SRR = shaped round robin. Ingress queues support shared mode only.


Table 2-3 shows the generated auto-QoS configuration for the egress queues.

Table 2-3 Auto-QoS Configuration for the Egress Queues

Egress Queue
Queue Number
CoS-to-Queue Map
Queue Weight (Bandwidth)
Queue (Buffer) Size for Gigabit-Capable Ports
Queue (Buffer) Size for 10/100 Ethernet Ports

Priority (shaped)

1

5

up to 100 percent

16 percent

10 percent

SRR shared

2

3, 6, 7

10 percent

6 percent

10 percent

SRR shared

3

2, 4

60 percent

17 percent

26 percent

SRR shared

4

0, 1

20 percent

61 percent

54 percent


Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Use this command to configure the QoS appropriate for VoIP traffic within the QoS domain. The QoS domain includes the switch, the interior of the network, and edge devices that can classify incoming traffic for QoS.

Auto-QoS configures the switch for VoIP with Cisco IP Phones on switch and routed ports and for VoIP with devices running the Cisco SoftPhone application. These releases support only Cisco IP SoftPhone Version 1.3(3) or later. Connected devices must use Cisco Call Manager Version 4 or later.

To take advantage of the auto-QoS defaults, you should enable auto-QoS before you configure other QoS commands. You can fine-tune the auto-QoS configuration after you enable auto-QoS.


Note The switch applies the auto-QoS-generated commands as if the commands were entered from the command-line interface (CLI). An existing user configuration can cause the application of the generated commands to fail or to be overridden by the generated commands. These actions occur without warning. If all the generated commands are successfully applied, any user-entered configuration that was not overridden remains in the running configuration. Any user-entered configuration that was overridden can be retrieved by reloading the switch without saving the current configuration to memory. If the generated commands fail to be applied, the previous running configuration is restored.


If this is the first port on which you have enabled auto-QoS, the auto-QoS-generated global configuration commands are executed followed by the interface configuration commands. If you enable auto-QoS on another port, only the auto-QoS-generated interface configuration commands for that port are executed.

When you enable the auto-QoS feature on the first port, these automatic actions occur:

QoS is globally enabled (mls qos global configuration command), and other global configuration commands are added.

When you enter the auto qos voip cisco-phone interface configuration command on a port at the edge of the network that is connected to a Cisco IP Phone, the switch enables the trusted boundary feature. The switch uses the Cisco Discovery Protocol (CDP) to detect the presence or absence of a Cisco IP Phone. When a Cisco IP Phone is detected, the ingress classification on the port is set to trust the QoS label received in the packet. The switch also uses policing to determine whether a packet is in or out of profile and to specify the action on the packet. If the packet does not have a DSCP value of 24, 26, or 46 or is out of profile, the switch changes the DSCP value to 0. When a Cisco IP Phone is absent, the ingress classification is set to not trust the QoS label in the packet. The switch configures ingress and egress queues on the port according to the settings in Table 2-2 and Table 2-3. The policing is applied to those traffic matching the policy-map classification before the switch enables the trust boundary feature.

When you enter the auto qos voip cisco-softphone interface configuration command on a port at the edge of the network that is connected to a device running the Cisco SoftPhone, the switch uses policing to decide whether a packet is in or out of profile and to specify the action on the packet. If the packet does not have a DSCP value of 24, 26, or 46 or is out of profile, the switch changes the DSCP value to 0. The switch configures ingress and egress queues on the port according to the settings in Table 2-2 and Table 2-3.

When you enter the auto qos voip trust interface configuration command on a port connected to the interior of the network, the switch trusts the CoS value for nonrouted ports or the DSCP value for routed ports in ingress packets (the assumption is that traffic has already been classified by other edge devices). The switch configures the ingress and egress queues on the port according to the settings in Table 2-2 and Table 2-3.

You can enable auto-QoS on static, dynamic-access, and voice VLAN access, and trunk ports. When enabling auto-QoS with a Cisco IP Phone on a routed port, you must assign a static IP address to the IP phone.


Note When a device running Cisco SoftPhone is connected to a switch or routed port, the switch supports only one Cisco SoftPhone application per port.


After auto-QoS is enabled, do not modify a policy map or aggregate policer that includes AutoQoS in its name. If you need to modify the policy map or aggregate policer, make a copy of it, and change the copied policy map or policer. To use the new policy map instead of the generated one, remove the generated policy map from the interface, and apply the new policy map.

To display the QoS configuration that is automatically generated when auto-QoS is enabled, enable debugging before you enable auto-QoS. Use the debug auto qos privileged EXEC command to enable auto-QoS debugging. For more information, see the debug auto qos command.

To disable auto-QoS on a port, use the no auto qos voip interface configuration command. Only the auto-QoS-generated interface configuration commands for this port are removed. If this is the last port on which auto-QoS is enabled and you enter the no auto qos voip command, auto-QoS is considered disabled even though the auto-QoS-generated global configuration commands remain (to avoid disrupting traffic on other ports affected by the global configuration). You can use the no mls qos global configuration command to disable the auto-QoS-generated global configuration commands. With QoS disabled, there is no concept of trusted or untrusted ports because the packets are not modified (the CoS, DSCP, and IP precedence values in the packet are not changed). Traffic is switched in pass-through mode (packets are switched without any rewrites and classified as best effort without any policing).

Examples

This example shows how to enable auto-QoS and to trust the QoS labels received in incoming packets when the switch or router connected to the port is a trusted device:

Switch(config)# interface gigabitethernet2/0/1
Switch(config-if)# auto qos voip trust

You can verify your settings by entering the show auto qos interface interface-id privileged EXEC command.

Related Commands

Command
Description

debug auto qos

Enables debugging of the auto-QoS feature.

mls qos cos

Defines the default CoS value of a port or assigns the default CoS to all incoming packets on the port.

mls qos map {cos-dscp dscp1 ... dscp8 | dscp-cos dscp-list to cos}

Defines the CoS-to-DSCP map or the DSCP-to-CoS map.

mls qos queue-set output buffers

Allocates buffers to a queue-set.

mls qos srr-queue input bandwidth

Assigns shaped round robin (SRR) weights to an ingress queue.

mls qos srr-queue input buffers

Allocates the buffers between the ingress queues.

mls qos srr-queue input cos-map

Maps CoS values to an ingress queue or maps CoS values to a queue and to a threshold ID.

mls qos srr-queue input dscp-map

Maps DSCP values to an ingress queue or maps DSCP values to a queue and to a threshold ID.

mls qos srr-queue input priority-queue

Configures the ingress priority queue and guarantees bandwidth.

mls qos srr-queue output cos-map

Maps CoS values to an egress queue or maps CoS values to a queue and to a threshold ID.

mls qos srr-queue output dscp-map

Maps DSCP values to an egress queue or maps DSCP values to a queue and to a threshold ID.

mls qos trust

Configures the port trust state.

queue-set

Maps a port to a queue-set.

show auto qos

Displays auto-QoS information.

show mls qos interface

Displays QoS information at the port level.

srr-queue bandwidth shape

Assigns the shaped weights and enables bandwidth shaping on the four egress queues mapped to a port.

srr-queue bandwidth share

Assigns the shared weights and enables bandwidth sharing on the four egress queues mapped to a port.


boot auto-copy-sw

Use the boot auto-copy-sw global configuration command from the stack master to enable the automatic upgrade (auto-upgrade) process. It automatically upgrades a switch in version-mismatch (VM) mode by copying the running software image on any stack member or by copying a tar file image in switch stack flash memory. Use the no form of this command to disable the auto-upgrade process.

boot auto-copy-sw

no boot auto-copy-sw


Note This command is supported only on Catalyst 3750-X switches.


Syntax Description

This command has no arguments or keywords.

Defaults

Enabled.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

A switch in VM mode is a switch that has a different minor version number than the version on the switch stack. A switch in VM mode cannot join the switch stack as a fully functioning member. If the switch stack has an image that can be copied to a switch in VM mode, the auto-upgrade process automatically copies the image from a stack member to the switch in VM mode. The switch then exits VM mode, reboots, and joins the switch stack as a fully functioning member.

The auto-upgrade process affects only switches in VM mode. It does not affect existing stack members.

Related Commands

Command
Description

show boot

Displays the settings of the boot environment variables.

show version

Displays version information for the hardware and firmware.


boot auto-download-sw

Use the boot auto-download-sw global configuration command on the switch stack to specify a URL pathname to use for the automatic software upgrades. Use the no form of this command to remove the software image.

boot auto-download-sw source-url

no boot auto-download-sw


Note This command is supported only on Catalyst 3750-X switches.


Syntax Description

source-url

The source URLs for the software images. The image-name.tar is the software image to download and install on the switch.

These options are supported:

Local flash file system syntax on the standalone switch or the stack master:
flash:

Local flash file system syntax on a stack member:
flash member number:

The member number can be from 1 to 9.

FTP syntax: ftp:[[//username[:password]@location]/directory]/image-name.tar

HTTP server syntax for an HTTP server:
http://[[username:password]@]{hostname | host-ip}[/directory]/image-name.tar

Secure HTTP server syntax:
https://[[username:password]@]{hostname | host-ip}[/directory]/image-name.tar

Remote Copy Protocol (RCP) syntax: rcp:[[//username@location]/directory]/image-name.tar

Secure Copy Protocol (SCP) syntax: scp:[[//username@location]/directory]/image-name.tar

TFTP syntax:
tftp:[[//location]/directory]/image-name.tar


Defaults

Disabled.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

This command specifies a URL path to use for automatic software upgrades.

You can use this command to configure the URL for the master switch to access in case of version-mismatch.

Related Commands

Command
Description

show boot

Displays the settings of the boot environment variables.

show version

Displays version information for the hardware and firmware.


boot config-file

Use the boot config-file global configuration command on a standalone switch to specify the filename that Cisco IOS uses to read and write a nonvolatile copy of the system configuration. Use the no form of this command to return to the default setting.

boot config-file flash:/file-url

no boot config-file

Syntax Description

flash:/file-url

The path (directory) and name of the configuration file.


Defaults

The default configuration file is flash:config.text.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

This command works properly only from a standalone switch in a stack.

Filenames and directory names are case sensitive.

This command changes the setting of the CONFIG_FILE environment variable. For more information, see Appendix A "Catalyst 3750-X and 3560-X Switch Boot Loader Commands."

Related Commands

Command
Description

show boot

Displays the settings of the boot environment variables.


boot enable-break

Use the boot enable-break global configuration command on a standalone switch to enable interrupting the automatic boot process. Use the no form of this command to return to the default setting.

boot enable-break

no boot enable-break

Syntax Description

This command has no arguments or keywords.

Defaults

Disabled. The automatic boot process cannot be interrupted by pressing the Break key on the console.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

This command works properly only from a standalone switch in a stack.

When you enter this command, you can interrupt the automatic boot process by pressing the Break key on the console after the flash file system is initialized.


Note Despite the setting of this command, you can interrupt the automatic boot process at any time by pressing the MODE button on the switch front panel.


This command changes the setting of the ENABLE_BREAK environment variable. For more information, see Appendix A "Catalyst 3750-X and 3560-X Switch Boot Loader Commands."

Related Commands

Command
Description

show boot

Displays the settings of the boot environment variables.


boot helper

Use the boot helper global configuration command on the switch stack or on a standalone switch to dynamically load files during boot loader initialization to extend or patch the functionality of the boot loader. Use the no form of this command to return to the default.

boot helper filesystem:/file-url ...

no boot helper

Syntax Description

filesystem:

Alias for a flash file system. Use flash: for the system board flash device.

/file-url

The path (directory) and a list of loadable files to dynamically load during loader initialization. Separate each image name with a semicolon.


Defaults

No helper files are loaded.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

This variable is used only for internal development and testing.

Filenames and directory names are case sensitive.

This command changes the setting of the HELPER environment variable. For more information, see Appendix A "Catalyst 3750-X and 3560-X Switch Boot Loader Commands."

Related Commands

Command
Description

show boot

Displays the settings of the boot environment variables.


boot helper-config-file

Use the boot helper-config-file global configuration command on the switch stack or on a standalone switch to specify the name of the configuration file to be used by the Cisco IOS helper image. If this is not set, the file specified by the CONFIG_FILE environment variable is used by all versions of Cisco IOS that are loaded. Use the no form of this command to return to the default setting.

boot helper-config-file filesystem:/file-url

no boot helper-config file

Syntax Description

filesystem:

Alias for a flash file system. Use flash: for the system board flash device.

/file-url

The path (directory) and helper configuration file to load.


Defaults

No helper configuration file is specified.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

This variable is used only for internal development and testing.

Filenames and directory names are case sensitive.

This command changes the setting of the HELPER_CONFIG_FILE environment variable. For more information, see Appendix A "Catalyst 3750-X and 3560-X Switch Boot Loader Commands."

Related Commands

Command
Description

show boot

Displays the settings of the boot environment variables.


boot manual

Use the boot manual global configuration command on a standalone switch to enable manually booting the switch during the next boot cycle. Use the no form of this command to return to the default setting.

boot manual

no boot manual

Syntax Description

This command has no arguments or keywords.

Defaults

Manual booting is disabled.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

This command works properly only from a standalone switch in a stack.

The next time you reboot the system, the switch is in boot loader mode, which is shown by the switch: prompt. To boot up the system, use the boot boot loader command, and specify the name of the bootable image.

This command changes the setting of the MANUAL_BOOT environment variable. For more information, see Appendix A "Catalyst 3750-X and 3560-X Switch Boot Loader Commands."

Related Commands

Command
Description

show boot

Displays the settings of the boot environment variables.


boot private-config-file

Use the boot private-config-file global configuration command on a standalone switch to specify the filename that Cisco IOS uses to read and write a nonvolatile copy of the private configuration. Use the no form of this command to return to the default setting.

boot private-config-file filename

no boot private-config-file

Syntax Description

filename

The name of the private configuration file.


Defaults

The default configuration file is private-config.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

This command works properly only from a standalone switch in a stack.

Filenames are case sensitive.

Examples

This example shows how to specify the name of the private configuration file to be pconfig:

Switch(config)# boot private-config-file pconfig

Related Commands

Command
Description

show boot

Displays the settings of the boot environment variables.


boot system

Use the boot system global configuration command on the switch stack or on a standalone switch to specify the Cisco IOS image to load during the next boot cycle. Use the no form of this command to return to the default setting.

boot system {filesystem:/file-url ...| switch {number | all}}

no boot system

no boot system switch {number | all}

Syntax Description

filesystem:

Alias for a flash file system. Use flash: for the system board flash device.

/file-url

The path (directory) and name of a bootable image. Separate image names with a semicolon.

switch

Specify the switches on which the Cisco IOS image is loaded.

This keyword is supported only on on stacking-capable switches.

number

Specify a stack member.

This keyword is supported only on on stacking-capable switches.

all

Specify all stack members.

This keyword is supported only on on stacking-capable switches.


Defaults

The switch attempts to automatically boot up the system by using information in the BOOT environment variable. If this variable is not set, the switch attempts to load and execute the first executable image it can by performing a recursive, depth-first search throughout the flash file system. In a depth-first search of a directory, each encountered subdirectory is completely searched before continuing the search in the original directory.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Filenames and directory names are case sensitive.

If you enter the boot system filesystem:/file-url command on the stack master, the specified software image is loaded only on the stack master during the next boot cycle.

On the stack master, use the boot system switch number command to specify that the software image is loaded on the specified stack member during the next boot cycle. Use the boot system switch all command to specify that the software image is loaded on all the stack members during the next boot cycle.

When you enter the boot system switch number or the boot system switch all command on the stack master, the stack master checks if a software image is already on the stack member (except on the stack master). If the software image does not exist on the stack member (for example, stack member 1), an error message like this appears:

%Command to set boot system switch all xxx on switch=1 failed

If you are using the archive download-sw privileged EXEC command to maintain system images, you never need to use the boot system command. The boot system command is automatically manipulated to load the downloaded image.

This command changes the setting of the BOOT environment variable. For more information, see Appendix A "Catalyst 3750-X and 3560-X Switch Boot Loader Commands."

Related Commands

Command
Description

show boot

Displays the settings of the boot environment variables.


cdp forward

To specify the ingress and egress switch ports for CDP traffic, use the cdp forward global configuration command. To return to the default setting, use the no form of this command.

cdp forward ingress port-id egress port-id

no cdp forward ingress port-id


Note This command is not supported on switches running the LAN base feature set.


Syntax Description

ingress port-id

Specifies the switch port that receives the CDP packet from an IP phone.

egress port-id

Specifies the switch port that forwards the CDP packet to the Cisco TelePresence System.


Defaults

The default path for CDP packets through the switch is from any ingress port to the egress port connected to the Cisco Telepresence System.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You must use only CDP-enabled phones with TelePresence E911 IP phone support.

You can connect the IP phone and codec in the Cisco TelePresence System through any two ports in a switch stack.

Examples

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# cdp forward ingress gigabitethernet2/0/1 egress gigabitethernet2/0/12
Switch(config)# cdp forward ingress gigabitethernet2/0/2 egress gigabitethernet2/0/13
Switch(config)# end
Switch# show running-config | include cdp
cdp forward ingress GigabitEthernet2/0/1 egress GigabitEthernet2/0/12
cdp forward ingress GigabitEthernet2/0/2 egress GigabitEthernet2/0/13
Switch# show cdp forward
Ingress         Egress         # packets         # packets
Port            Port           forwarded         dropped
-------------------------------------------------------------
 Gi2/0/1        Gi2/0/12            0                0
 Gi2/0/2        Gi2/0/13            0                0

Related Commands

Command
Description

show cdp forward

Displays the CDP forwarding table.


channel-group

Use the channel-group interface configuration command on the switch stack or on a standalone switch to assign an Ethernet port to an EtherChannel group, to enable an EtherChannel mode, or both. Use the no form of this command to remove an Ethernet port from an EtherChannel group.

channel-group channel-group-number mode {active | {auto [non-silent]} | {desirable [non-silent]} | on | passive}

no channel-group

PAgP modes:
channel-group channel-group-number mode {{auto [non-silent]} | {desirable [non-silent}}

LACP modes:
channel-group channel-group-number mode {active | passive}

On mode:
channel-group channel-group-number mode on

Syntax Description

channel-group-number

Specify the channel group number. The range is 1 to 48.

mode

Specify the EtherChannel mode.

active

Unconditionally enable Link Aggregation Control Protocol (LACP).

Active mode places a port into a negotiating state in which the port initiates negotiations with other ports by sending LACP packets. A channel is formed with another port group in either the active or passive mode.

auto

Enable the Port Aggregation Protocol (PAgP) only if a PAgP device is detected.

Auto mode places a port into a passive negotiating state in which the port responds to PAgP packets it receives but does not start PAgP packet negotiation. A channel is formed only with another port group in desirable mode. When auto is enabled, silent operation is the default.

desirable

Unconditionally enable PAgP.

Desirable mode places a port into an active negotiating state in which the port starts negotiations with other ports by sending PAgP packets. An EtherChannel is formed with another port group that is in the desirable or auto mode. When desirable is enabled, silent operation is the default.

non-silent

(Optional) Use in PAgP mode with the auto or desirable keyword when traffic is expected from the other device.

on

Enable on mode.

In on mode, a usable EtherChannel exists only when both connected port groups are in the on mode.

passive

Enable LACP only if a LACP device is detected.

Passive mode places a port into a negotiating state in which the port responds to received LACP packets but does not initiate LACP packet negotiation. A channel is formed only with another port group in active mode.


Defaults

No channel groups are assigned.

No mode is configured.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

For Layer 2 EtherChannels, you do not have to create a port-channel interface first by using the interface port-channel global configuration command before assigning a physical port to a channel group. Instead, you can use the channel-group interface configuration command. It automatically creates the port-channel interface when the channel group gets its first physical port if the logical interface is not already created. If you create the port-channel interface first, the channel-group-number can be the same as the port-channel-number, or you can use a new number. If you use a new number, the channel-group command dynamically creates a new port channel.

You do not have to disable the IP address that is assigned to a physical port that is part of a channel group, but we strongly recommend that you do so.

You create Layer 3 port channels by using the interface port-channel command followed by the no switchport interface configuration command. You should manually configure the port-channel logical interface before putting the interface into the channel group.

After you configure an EtherChannel, configuration changes that you make on the port-channel interface apply to all the physical ports assigned to the port-channel interface. Configuration changes applied to the physical port affect only the port where you apply the configuration. To change the parameters of all ports in an EtherChannel, apply configuration commands to the port-channel interface, for example, spanning-tree commands or commands to configure a Layer 2 EtherChannel as a trunk.

If you do not specify non-silent with the auto or desirable mode, silent is assumed. The silent mode is used when the switch is connected to a device that is not PAgP-capable and seldom, if ever, sends packets. A example of a silent partner is a file server or a packet analyzer that is not generating traffic. In this case, running PAgP on a physical port prevents that port from ever becoming operational. However, it allows PAgP to operate, to attach the port to a channel group, and to use the port for transmission. Both ends of the link cannot be set to silent.

In the on mode, an EtherChannel exists only when a port group in the on mode is connected to another port group in the on mode.


Caution You should use care when using the on mode. This is a manual configuration, and ports on both ends of the EtherChannel must have the same configuration. If the group is misconfigured, packet loss or spanning-tree loops can occur.

Do not configure an EtherChannel in both the PAgP and LACP modes. EtherChannel groups running PAgP and LACP can coexist on the same switch or on different switches in the stack (but not in a cross-stack configuration). Individual EtherChannel groups can run either PAgP or LACP, but they cannot interoperate.

If you set the protocol by using the channel-protocol interface configuration command, the setting is not overridden by the channel-group interface configuration command.

Do not configure a port that is an active or a not-yet-active member of an EtherChannel as an IEEE 802.1x port. If you try to enable IEEE 802.1x authentication on an EtherChannel port, an error message appears, and IEEE 802.1x authentication is not enabled.

Do not configure a secure port as part of an EtherChannel or an EtherChannel port as a secure port.

For a complete list of configuration guidelines, see the "Configuring EtherChannels" chapter in the software configuration guide for this release.


Caution Do not enable Layer 3 addresses on the physical EtherChannel ports. Do not assign bridge groups on the physical EtherChannel ports because it creates loops.

Examples

This example shows how to configure an EtherChannel on a single switch in the stack. It assigns two static-access ports in VLAN 10 to channel 5 with the PAgP mode desirable:

Switch# configure terminal 
Switch(config)# interface range gigabitethernet2/0/1 -2 
Switch(config-if-range)# switchport mode access
Switch(config-if-range)# switchport access vlan 10
Switch(config-if-range)# channel-group 5 mode desirable 
Switch(config-if-range)# end 

This example shows how to configure an EtherChannel on a single switch in the stack. It assigns two static-access ports in VLAN 10 to channel 5 with the LACP mode active:

Switch# configure terminal 
Switch(config)# interface range gigabitethernet2/0/1 -2 
Switch(config-if-range)# switchport mode access
Switch(config-if-range)# switchport access vlan 10
Switch(config-if-range)# channel-group 5 mode active 
Switch(config-if-range)# end 

This example shows how to configure a cross-stack EtherChannel in a switch stack. It uses LACP passive mode and assigns two ports on stack member 2 and one port on stack member 3 as static-access ports in VLAN 10 to channel 5:

Switch# configure terminal 
Switch(config)# interface range gigabitethernet2/0/4 -5 
Switch(config-if-range)# switchport mode access
Switch(config-if-range)# switchport access vlan 10
Switch(config-if-range)# channel-group 5 mode passive 
Switch(config-if-range)# exit
Switch(config)# interface gigabitethernet3/0/3 
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 10
Switch(config-if)# channel-group 5 mode passive 
Switch(config-if)# exit

You can verify your settings by entering the show running-config privileged EXEC command.

Related Commands

Command
Description

channel-protocol

Restricts the protocol used on a port to manage channeling.

interface port-channel

Accesses or creates the port channel.

show etherchannel

Displays EtherChannel information for a channel.

show lacp

Displays LACP channel-group information.

show pagp

Displays PAgP channel-group information.

show running-config

Displays the operating configuration. For syntax information, use this link to the Cisco IOS Release 12.2 Command Reference listing page: http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/prod_command_reference_list.html
Select the Cisco IOS Commands Master List, Release 12.2 to navigate to the command.


channel-protocol

Use the channel-protocol interface configuration command on the switch stack or on a standalone switch to restrict the protocol used on a port to manage channeling. Use the no form of this command to return to the default setting.

channel-protocol {lacp | pagp}

no channel-protocol

Syntax Description

lacp

Configure an EtherChannel with the Link Aggregation Control Protocol (LACP).

pagp

Configure an EtherChannel with the Port Aggregation Protocol (PAgP).


Defaults

No protocol is assigned to the EtherChannel.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Use the channel-protocol command only to restrict a channel to LACP or PAgP. If you set the protocol by using the channel-protocol command, the setting is not overridden by the channel-group interface configuration command.

You must use the channel-group interface configuration command to configure the EtherChannel parameters. The channel-group command also can set the mode for the EtherChannel.

You cannot enable both the PAgP and LACP modes on an EtherChannel group.

PAgP and LACP are not compatible; both ends of a channel must use the same protocol.

Examples

This example shows how to specify LACP as the protocol that manages the EtherChannel:

Switch(config-if)# channel-protocol lacp

You can verify your settings by entering the show etherchannel [channel-group-number] protocol privileged EXEC command.

Related Commands

Command
Description

channel-group

Assigns an Ethernet port to an EtherChannel group.

show etherchannel protocol

Displays protocol information the EtherChannel.


cisp enable

Use the cisp enable global configuration command to enable Client Information Signalling Protocol (CISP) on a switch so that it acts as an authenticator to a supplicant switch.

cisp enable

no cisp enable

Syntax Description

cisp enable

Enable CISP.


Defaults

There is no default setting.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

The link between the authenticator and supplicant switch is a trunk. When you enable VTP on both switches, the VTP domain name must be the same, and the VTP mode must be server.

When you configure VTP mode, to avoid the MD5 checksum mismatch error, verify that:

VLANs are not configured on two different.switches, which can be caused by two VTP servers in the same domain.

Both switches have the different configuration revision numbers.

Examples

This example shows how to enable CISP:

switch(config)# cisp enable 

Related Commands

Command
Description

dot1x credentials (global configuration) profile

Configures a profile on a supplicant switch.

show cisp

Displays CISP information for a specified interface.


class

Use the class policy-map configuration command on the switch stack or on a standalone switch to define a traffic classification match criteria (through the police, set, and trust policy-map class configuration commands) for the specified class-map name. Use the no form of this command to delete an existing class map.

class class-map-name

no class class-map-name

Syntax Description

class-map-name

Name of the class map.


Defaults

No policy map class-maps are defined.

Command Modes

Policy-map configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Before using the class command, you must use the policy-map global configuration command to identify the policy map and to enter policy-map configuration mode. After specifying a policy map, you can configure a policy for new classes or modify a policy for any existing classes in that policy map. You attach the policy map to a port by using the service-policy interface configuration command.

After entering the class command, you enter policy-map class configuration mode, and these configuration commands are available:

exit: exits policy-map class configuration mode and returns to policy-map configuration mode.

no: returns a command to its default setting.

police: defines a policer or aggregate policer for the classified traffic. The policer specifies the bandwidth limitations and the action to take when the limits are exceeded. For more information, see the police and police aggregate policy-map class commands.

set: specifies a value to be assigned to the classified traffic. For more information, see the set command.

trust: defines a trust state for traffic classified with the class or the class-map command. For more information, see the trust command.

To return to policy-map configuration mode, use the exit command. To return to privileged EXEC mode, use the end command.

The class command performs the same function as the class-map global configuration command. Use the class command when a new classification, which is not shared with any other ports, is needed. Use the class-map command when the map is shared among many ports.

Examples

This example shows how to create a policy map called policy1. When attached to the ingress direction, it matches all the incoming traffic defined in class1, sets the IP Differentiated Services Code Point (DSCP) to 10, and polices the traffic at an average rate of 1 Mb/s and bursts at 20 KB. Traffic exceeding the profile is marked down to a DSCP value gotten from the policed-DSCP map and then sent.

Switch(config)# policy-map policy1
Switch(config-pmap)# class class1
Switch(config-pmap-c)# set dscp 10
Switch(config-pmap-c)# police 1000000 20000 exceed-action policed-dscp-transmit
Switch(config-pmap-c)# exit

You can verify your settings by entering the show policy-map privileged EXEC command.

Related Commands

Command
Description

class-map

Creates a class map to be used for matching packets to the class whose name you specify.

police

Defines a policer for classified traffic.

policy-map

Creates or modifies a policy map that can be attached to multiple ports to specify a service policy.

set

Classifies IP traffic by setting a DSCP or IP-precedence value in the packet.

show policy-map

Displays quality of service (QoS) policy maps.

trust

Defines a trust state for the traffic classified through the class policy-map configuration command or the class-map global configuration command.


class-map

Use the class-map global configuration command on the switch stack or on a standalone switch to create a class map to be used for matching packets to the class whose name you specify and to enter class-map configuration mode. Use the no form of this command to delete an existing class map and to return to global configuration mode.

class-map [match-all | match-any] class-map-name

no class-map [match-all | match-any] class-map-name

Syntax Description

match-all

(Optional) Perform a logical-AND of all matching statements under this class map. All criteria in the class map must be matched.

match-any

(Optional) Perform a logical-OR of the matching statements under this class map. One or more criteria must be matched.

class-map-name

Name of the class map.


Defaults

No class maps are defined.

If neither the match-all or match-any keyword is specified, the default is match-all.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Use this command to specify the name of the class for which you want to create or modify class-map match criteria and to enter class-map configuration mode.

The class-map command and its subcommands are used to define packet classification, marking, and aggregate policing as part of a globally named service policy applied on a per-port basis.

After you are in quality of service (QoS) class-map configuration mode, these configuration commands are available:

description: describes the class map (up to 200 characters). The show class-map privileged EXEC command displays the description and the name of the class-map.

exit: exits from QoS class-map configuration mode.

match: configures classification criteria. For more information, see the match (class-map configuration) command.

no: removes a match statement from a class map.

rename: renames the current class map. If you rename a class map with a name that is already used, the message A class-map with this name already exists appears.

If you enter the match-all or match-any keyword, you can only use it to specify an extended named access control list (ACL) with the match access-group acl-index-or-name class-map configuration command.

To define packet classification on a physical-port basis, only one match command per class map is supported. In this situation, the match-all and match-any keywords are equivalent.

Only one ACL can be configured in a class map. The ACL can have multiple access control entries (ACEs).

Examples

This example shows how to configure the class map called class1 with one match criterion, which is an access list called 103:

Switch(config)# access-list 103 permit ip any any dscp 10
Switch(config)# class-map class1
Switch(config-cmap)# match access-group 103
Switch(config-cmap)# exit

This example shows how to delete the class map class1:

Switch(config)# no class-map class1

You can verify your settings by entering the show class-map privileged EXEC command.

Related Commands

Command
Description

class

Defines a traffic classification match criteria (through the police, set, and trust policy-map class configuration commands) for the specified class-map name.

match (class-map configuration)

Defines the match criteria to classify traffic.

policy-map

Creates or modifies a policy map that can be attached to multiple ports to specify a service policy.

show class-map

Displays QoS class maps.


clear dot1x

Use the clear dot1x privileged EXEC command on the switch stack or on a standalone switch to clear IEEE 802.1x information for the switch or for the specified port.

clear dot1x {all | interface interface-id}

Syntax Description

all

Clear all IEEE 802.1x information for the switch.

interface interface-id

Clear IEEE 802.1x information for the specified interface.


Defaults

No default is defined.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You can clear all the information by using the clear dot1x all command, or you can clear only the information for the specified interface by using the clear dot1x interface interface-id command.

Examples

This example shows how to clear all IEEE 8021.x information:

Switch# clear dot1x all

This example shows how to clear IEEE 8021.x information for the specified interface:

Switch# clear dot1x interface gigabithethernet1/0/1

You can verify that the information was deleted by entering the show dot1x privileged EXEC command.

Related Commands

Command
Description

show dot1x

Displays IEEE 802.1x statistics, administrative status, and operational status for the switch or for the specified port.


clear eap sessions

Use the clear eap sessions privileged EXEC command on the switch stack or on a standalone switch to clear Extensible Authentication Protocol (EAP) session information for the switch or for the specified port.

clear eap sessions [credentials name [interface interface-id] | interface interface-id | method name | transport name] [credentials name | interface interface-id | transport name] ...

Syntax Description

credentials name

Clear EAP credential information for the specified profile.

interface interface-id

Clear EAP information for the specified interface.

method name

Clear EAP information for the specified method.

transport name

Clear EAP transport information for the specified lower level.


Defaults

No default is defined.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You can clear all counters by using the clear eap sessions command, or you can clear only the specific information by using the keywords.

Examples

This example shows how to clear all EAP information:

Switch# clear eap sessions

This example shows how to clear EAP-session credential information for the specified profile:

Switch# clear eap sessions credential type1


You can verify that the information was deleted by entering the show dot1x privileged EXEC command.

Related Commands

Command
Description

show eap

Displays EAP registration and session information for the switch or for the specified port


clear errdisable interface

Use the clear errdisable interface privileged EXEC command on the switch stack or on a standalone switch to re-enable a VLAN that was error disabled.

clear errdisable interface interface-id vlan [vlan-list]

Syntax Description

vlan list

(Optional) Specify a list of VLANs to be re-enabled. If a vlan-list is not specified, then all VLANs are re-enabled.


Command Default

No default is defined

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You can re-enable a port by using the shutdown and no shutdown interface configuration commands, or you can clear error disable for VLANs by using the clear errdisable interface command.

Examples

This example shows how to re-enable all VLANs that were error-disabled on Gigabit Ethernet port 4/0/2.

Switch# clear errdisable interface gigabitethernet4/0/2 vlan

Related Commands

Command
Description

errdisable detect cause

Enables error-disabled detection for a specific cause or all causes.

errdisable recovery

Configures the recovery mechanism variables.

show errdisable detect

Displays error-disabled detection status.

show errdisable recovery

Display error-disabled recovery timer information.

show interfaces status err-disabled

Displays interface status of a list of interfaces in error-disabled state.


clear ip arp inspection log

Use the clear ip arp inspection log privileged EXEC command on the switch stack or on a standalone switch to clear the dynamic Address Resolution Protocol (ARP) inspection log buffer.

clear ip arp inspection log

Syntax Description

This command has no arguments or keywords.

Defaults

No default is defined.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Examples

This example shows how to clear the contents of the log buffer:

Switch# clear ip arp inspection log

You can verify that the log was cleared by entering the show ip arp inspection log privileged command.

Related Commands

Command
Description

arp access-list

Defines an ARP access control list (ACL).

ip arp inspection log-buffer

Configures the dynamic ARP inspection logging buffer.

ip arp inspection vlan logging

Controls the type of packets that are logged per VLAN.

show inventory log

Displays the configuration and contents of the dynamic ARP inspection log buffer.


clear ip arp inspection statistics

Use the clear ip arp inspection statistics privileged EXEC command on the switch stack or on a standalone switch to clear the dynamic Address Resolution Protocol (ARP) inspection statistics.

clear ip arp inspection statistics [vlan vlan-range]

Syntax Description

vlan vlan-range

(Optional) Clear statistics for the specified VLAN or VLANs.

You can specify a single VLAN identified by VLAN ID number, a range of VLANs separated by a hyphen, or a series of VLANs separated by a comma. The range is 1 to 4094.


Defaults

No default is defined.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Examples

This example shows how to clear the statistics for VLAN 1:

Switch# clear ip arp inspection statistics vlan 1

You can verify that the statistics were deleted by entering the show ip arp inspection statistics vlan 1 privileged EXEC command.

Related Commands

Command
Description

show inventory statistics

Displays statistics for forwarded, dropped, MAC validation failure, and IP validation failure packets for all VLANs or the specified VLAN.


clear ip dhcp snooping

Use the clear ip dhcp snooping privileged EXEC command on the switch stack or on a standalone switch to clear the DHCP binding database agent statistics or the DHCP snooping statistics counters.

clear ip dhcp snooping {binding {* | ip-address | interface interface-id | vlan vlan-id} | database statistics | statistics}

Syntax Description

binding

Clear the DHCP snooping binding database.

*

Clear all automatic bindings.

ip-address

Clear the binding entry IP address.

interface interface-id

Clear the binding input interface.

vlan vlan-id

Clear the binding entry VLAN.

database statistics

Clear the DHCP snooping binding database agent statistics.

statistics

Clear the DHCP snooping statistics counter.


Defaults

No default is defined.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

When you enter the clear ip dhcp snooping database statistics command, the switch does not update the entries in the binding database and in the binding file before clearing the statistics.

Examples

This example shows how to clear the DHCP snooping binding database agent statistics:

Switch# clear ip dhcp snooping database statistics 

You can verify that the statistics were cleared by entering the show ip dhcp snooping database privileged EXEC command.

This example shows how to clear the DHCP snooping statistics counters:

Switch# clear ip dhcp snooping statistics 

You can verify that the statistics were cleared by entering the show ip dhcp snooping statistics user EXEC command.

Related Commands

Command
Description

ip dhcp snooping

Enables DHCP snooping on a VLAN.

ip dhcp snooping database

Configures the DHCP snooping binding database agent or the binding file.

show ip dhcp snooping binding

Displays the status of DHCP snooping database agent.

show ip dhcp snooping database

Displays the DHCP snooping binding database agent statistics.

show ip dhcp snooping statistics

Displays the DHCP snooping statistics.


clear ipc

Use the clear ipc privileged EXEC command on the switch stack or on a standalone switch to clear Interprocess Communications Protocol (IPC) statistics.

clear ipc {queue-statistics | statistics}


Note This command is not supported on switches running the LAN base feature set.


Syntax Description

queue-statistics

Clear the IPC queue statistics.

statistics

Clear the IPC statistics.


Defaults

No default is defined.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You can clear all statistics by using the clear ipc statistics command, or you can clear only the queue statistics by using the clear ipc queue-statistics command.

Examples

This example shows how to clear all statistics:

Switch# clear ipc statistics

This example shows how to clear only the queue statistics:

Switch# clear ipc queue-statistics

You can verify that the statistics were deleted by entering the show ipc rpc or the show ipc session privileged EXEC command.

Related Commands

Command
Description

show ipc {rpc | session}

Displays the IPC multicast routing statistics.


clear ipv6 dhcp conflict

Use the clear ipv6 dhcp conflict privileged EXEC command on the switch stack or on a standalone switch to clear an address conflict from the Dynamic Host Configuration Protocol for IPv6 (DHCPv6) server database.

clear ipv6 dhcp conflict {* | IPv6-address}


Note This command is available only if you have configured a dual IPv4 and IPv6 Switch Database Management (SDM) template on the switch. This command is not supported if the switch is running the LAN base feature set.


Syntax Description

*

Clear all address conflicts.

IPv6-address

Clear the host IPv6 address that contains the conflicting address.


Defaults

No default is defined.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

To configure the dual IPv4 and IPv6 template, enter the sdm prefer dual-ipv4-and-ipv6 {default | vlan} global configuration command, and reload the switch.

When you configure the DHCPv6 server to detect conflicts, it uses ping. The client uses neighbor discovery to detect clients and reports to the server through a DECLINE message. If an address conflict is detected, the address is removed from the pool, and the address is not assigned until the administrator removes the address from the conflict list.

If you use the asterisk (*) character as the address parameter, DHCP clears all conflicts.

Examples

This example shows how to clear all address conflicts from the DHCPv6 server database:

Switch# clear ipv6 dhcp conflict *

Related Commands

Command
Description

show ipv6 dhcp conflict

Displays address conflicts found by a DHCPv6 server, or reported through a DECLINE message from a client.


clear l2protocol-tunnel counters

Use the clear l2protocol-tunnel counters privileged EXEC command on the switch stack or on a standalone switch to clear the protocol counters in protocol tunnel ports.

clear l2protocol-tunnel counters [interface-id]


Note This command is not supported on switches running the LAN base feature set.


Syntax Description

interface-id

(Optional) Specify the interface (physical interface or port channel) for which protocol counters are to be cleared.


Defaults

No default is defined.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Use this command to clear protocol tunnel counters on the switch or on the specified interface.

Examples

This example shows how to clear Layer 2 protocol tunnel counters on an interface:

Switch# clear l2protocol-tunnel counters gigabitethernet1/0/3

Related Commands

Command
Description

show l2protocol-tunnel

Displays information about ports configured for Layer 2 protocol tunneling.


clear lacp

Use the clear lacp privileged EXEC command on the switch stack or on a standalone switch to clear Link Aggregation Control Protocol (LACP) channel-group counters.

clear lacp {channel-group-number counters | counters}

Syntax Description

channel-group-number

(Optional) Channel group number. The range is 1 to 48.

counters

Clear traffic counters.


Defaults

No default is defined.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You can clear all counters by using the clear lacp counters command, or you can clear only the counters for the specified channel group by using the clear lacp channel-group-number counters command.

Examples

This example shows how to clear all channel-group information:

Switch# clear lacp counters

This example shows how to clear LACP traffic counters for group 4:

Switch# clear lacp 4 counters

You can verify that the information was deleted by entering the show lacp counters or the show lacp 4 counters privileged EXEC command.

Related Commands

Command
Description

show lacp

Displays LACP channel-group information.


clear logging onboard

Use the clear logging onboard privileged EXEC command on the switch stack or on a standalone switch to clear all of the on-board failure logging (OBFL) data except for the uptime and CLI-command information stored in the flash memory.

clear logging onboard

Syntax Description

This command has no arguments or keywords.

Defaults

No default is defined.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

We recommend that you keep OBFL enabled and do not erase the data stored in the flash memory.

Examples

This example shows how to clear all the OBFL information except for the uptime and CLI-command information:

Switch# clear logging onboard
Clear logging onboard buffer [confirm]

You can verify that the information was deleted by entering the show logging onboard onboard privileged EXEC command.

Related Commands

Command
Description

hw-module module [switch-number] logging onboard

Enables OBFL.

show logging onboard onboard

Displays OBFL information.


clear mac address-table

Use the clear mac address-table privileged EXEC command on the switch stack or on a standalone switch to delete from the MAC address table a specific dynamic address, all dynamic addresses on a particular interface, all dynamic addresses on stack members, or all dynamic addresses on a particular VLAN. This command also clears the MAC address notification global counters.

clear mac address-table {dynamic [address mac-addr | interface interface-id | vlan vlan-id] | notification}

Syntax Description

dynamic

Delete all dynamic MAC addresses.

dynamic address mac-addr

(Optional) Delete the specified dynamic MAC address.

dynamic interface interface-id

(Optional) Delete all dynamic MAC addresses on the specified physical port or port channel.

dynamic vlan vlan-id

(Optional) Delete all dynamic MAC addresses for the specified VLAN. The range is 1 to 4094.

notification

Clear the notifications in the history table and reset the counters.


Defaults

No default is defined.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Examples

This example shows how to remove a specific MAC address from the dynamic address table:

Switch# clear mac address-table dynamic address 0008.0070.0007

You can verify that the information was deleted by entering the show mac address-table privileged EXEC command.

Related Commands

Command
Description

mac address-table notification

Enables the MAC address notification feature.

\show mac address-table

Displays the MAC address table static and dynamic entries.

show mac address-table notification

Displays the MAC address notification settings for all interfaces or the specified interface.

snmp trap mac-notification change

Enables the Simple Network Management Protocol (SNMP) MAC address notification trap on a specific interface.


clear mac address-table move update

Use the clear mac address-table move update privileged EXEC command on the switch stack or on a standalone switch to clear the MAC address table move-update counters.

clear mac address-table move update

Syntax Description

This command has no arguments or keywords.

Defaults

No default is defined.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Examples

This example shows how to clear the MAC address table move-update counters.

Switch# clear mac address-table move update

You can verify that the information was cleared by entering the show mac address-table move update privileged EXEC command.

Related Commands

Command
Description

mac address-table move update {receive | transmit}

Configures MAC address-table move update on the switch.

show mac address-table move update

Displays the MAC address-table move update information on the switch.


clear macsec counters interface

To clear Media Access Control Security (MACsec) counters for all interfaces or a specified interface, use the clear macsec counters interface privileged EXEC command.

clear macsec counters interface [interface-id]

Syntax Description

interface-id

(Optional) Clears MACsec counters only for the specified interface.


Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Examples

This example clears all MACsec counters on all interfaces:

Switch# clear macsec counters interface

This example clears the MACsec counters on the specified interface:

Switch# clear macsec counters interface gigabitethernet 1/0/2

Related Commands

Command
Description

clear mka

Clears MACsec Key Agreement (MKA) protocol policies or information.

macsec

Enables MACsec on an interface.

show macsec

Displays MACsec information.


clear mka

To clear MACsec Key Agreement (MKA) protocol sessions or information, use the clear mka privileged EXEC command.

clear mka {all | sessions [interface interface-id [port-id port-id]] | [local-sci sci] | statistics [interface interface-id port-id port-id] | [local-sci sci]}

Syntax Description

all

Clears all MKA sessions and global statistics.

sessions

Clears all MKA sessions.

interface interface-id

(Optional) Clears all active MKA sessions on the interface.

port-id port-id

(Optional) Clears the MKA session on the specified interface with the specified port ID. The port-ID range is 1 to 65535.

local-sci sci

(Optional) Clears all active MKA sessions with the specified Local TX-SCI, a 64-bit hexadecimal string.

statistics

Clears all MKA statistics and error counters. Enter additional keywords to clear counters only for an interface or Local TX-SCI.

interface interface-id port-id port-idClears MKA session statistics for the specified interface and port ID.

local-sci sciClears MKA session statistics for the specified Local TX-SCI.


Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

When you enter the clear mka all command, the switch prompts for a confirmation and then deletes all active MKA sessions.

Examples

This example clears all active MKA sessions:

Switch# clear mka all
Are you sure you want to do this? [yes/no]: yes

This example clears the statistics counter of a specific MKA session running with Local TX-SCI 0023330853030002:

Switch# clear mka statistics local-sci 0023330853030002 

Related Commands

Command
Description

show mka policy

Displays MKA policy configuration information.

show mka sessions

Displays a summary of MKA sessions.

show mka statistics

Displays global MKA statistics.

show mka summary

Displays MKA sessions summary and global statistics.


clear nmsp statistics

Use the clear nmsp statistics privileged EXEC command to clear the Network Mobility Services Protocol (NMSP) statistics.

clear nmsp statistics

Syntax Description

This command has no arguments or keywords.

Defaults

No default is defined.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Examples

This example shows how to clear NMSP statistics:

Switch# clear nmsp statistics

You can verify that information was deleted by entering the show nmsp statistics privileged EXEC command.

Related Commands

Command
Description

show nmsp

Displays the NMSP information.


clear pagp

Use the clear pagp privileged EXEC command on the switch stack or on a standalone switch to clear Port Aggregation Protocol (PAgP) channel-group information.

clear pagp {channel-group-number counters | counters}

Syntax Description

channel-group-number

(Optional) Channel group number. The range is 1 to 48.

counters

Clear traffic counters.


Defaults

No default is defined.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You can clear all counters by using the clear pagp counters command, or you can clear only the counters for the specified channel group by using the clear pagp channel-group-number counters command.

Examples

This example shows how to clear all channel-group information:

Switch# clear pagp counters

This example shows how to clear PAgP traffic counters for group 10:

Switch# clear pagp 10 counters

You can verify that information was deleted by entering the show pagp privileged EXEC command.

Related Commands

Command
Description

show pagp

Displays PAgP channel-group information.


clear port-security

Use the clear port-security privileged EXEC command on the switch stack or on a standalone switch to delete from the MAC address table all secure addresses or all secure addresses of a specific type (configured, dynamic, or sticky) on the switch or on an interface.

clear port-security {all | configured | dynamic | sticky} [[address mac-addr | interface interface-id] [vlan {vlan-id | {access | voice}}]]

Syntax Description

all

Delete all secure MAC addresses.

configured

Delete configured secure MAC addresses.

dynamic

Delete secure MAC addresses auto-learned by hardware.

sticky

Delete secure MAC addresses, either auto-learned or configured.

address mac-addr

(Optional) Delete the specified dynamic secure MAC address.

interface interface-id

(Optional) Delete all the dynamic secure MAC addresses on the specified physical port or VLAN.

vlan

(Optional) Delete the specified secure MAC address from the specified VLAN. Enter one of these options after you enter the vlan keyword:

vlan-id—On a trunk port, specify the VLAN ID of the VLAN on which this address should be cleared.

access—On an access port, clear the specified secure MAC address on the access VLAN.

voice—On an access port, clear the specified secure MAC address on the voice VLAN.

Note The voice keyword is available only if voice VLAN is configured on a port and if that port is not the access VLAN.


Defaults

No default is defined.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Examples

This example shows how to clear all secure addresses from the MAC address table:

Switch# clear port-security all

This example shows how to remove a specific configured secure address from the MAC address table:

Switch# clear port-security configured address 0008.0070.0007

This example shows how to remove all the dynamic secure addresses learned on a specific interface:

Switch# clear port-security dynamic interface gigabitethernet1/0/1

This example shows how to remove all the dynamic secure addresses from the address table:

Switch# clear port-security dynamic

You can verify that the information was deleted by entering the show port-security privileged EXEC command.

Related Commands

Command
Description

switchport port-security

Enables port security on an interface.

switchport port-security mac-address mac-address

Configures secure MAC addresses.

switchport port-security maximum value

Configures a maximum number of secure MAC addresses on a secure interface.

show port-security

Displays the port security settings defined for an interface or for the switch.


clear spanning-tree counters

Use the clear spanning-tree counters privileged EXEC command on the switch stack or on a standalone switch to clear the spanning-tree counters.

clear spanning-tree counters [interface interface-id]

Syntax Description

interface interface-id

(Optional) Clear all spanning-tree counters on the specified interface. Valid interfaces include physical ports, VLANs, and port channels. The VLAN range is 1 to 4094. The port-channel range is 1 to 48.


Defaults

No default is defined.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

If the interface-id is not specified, spanning-tree counters are cleared for all interfaces.

Examples

This example shows how to clear spanning-tree counters for all interfaces:

Switch# clear spanning-tree counters

Related Commands

Command
Description

show spanning-tree

Displays spanning-tree state information.


clear spanning-tree detected-protocols

Use the clear spanning-tree detected-protocols privileged EXEC command on the switch stack or on a standalone switch to restart the protocol migration process (force the renegotiation with neighboring switches) on all interfaces or on the specified interface.

clear spanning-tree detected-protocols [interface interface-id]

Syntax Description

interface interface-id

(Optional) Restart the protocol migration process on the specified interface. Valid interfaces include physical ports, VLANs, and port channels. The VLAN range is 1 to 4094. The port-channel range is 1 to 48.


Defaults

No default is defined.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

A switch running the rapid per-VLAN spanning-tree plus (rapid-PVST+) protocol or the Multiple Spanning Tree Protocol (MSTP) supports a built-in protocol migration mechanism that enables it to interoperate with legacy IEEE 802.1D switches. If a rapid-PVST+ switch or an MSTP switch receives a legacy IEEE 802.1D configuration bridge protocol data unit (BPDU) with the protocol version set to 0, it sends only IEEE 802.1D BPDUs on that port. A multiple spanning-tree (MST) switch can also detect that a port is at the boundary of a region when it receives a legacy BPDU, an MST BPDU (Version 3) associated with a different region, or a rapid spanning-tree (RST) BPDU (Version 2).

However, the switch does not automatically revert to the rapid-PVST+ or the MSTP mode if it no longer receives IEEE 802.1D BPDUs because it cannot learn whether the legacy switch has been removed from the link unless the legacy switch is the designated switch. Use the clear spanning-tree detected-protocols command in this situation.

Examples

This example shows how to restart the protocol migration process on a port:

Switch# clear spanning-tree detected-protocols interface gigabitethernet2/0/1

Related Commands

Command
Description

show spanning-tree

Displays spanning-tree state information.

spanning-tree link-type

Overrides the default link-type setting and enables rapid spanning-tree changes to the forwarding state.


clear vmps statistics

Use the clear vmps statistics privileged EXEC command on the switch stack or on a standalone switch to clear the statistics maintained by the VLAN Query Protocol (VQP) client.

clear vmps statistics

Syntax Description

This command has no arguments or keywords.

Defaults

No default is defined.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Examples

This example shows how to clear VLAN Membership Policy Server (VMPS) statistics:

Switch# clear vmps statistics

You can verify that information was deleted by entering the show vmps statistics privileged EXEC command.

Related Commands

Command
Description

show vmps

Displays the VQP version, reconfirmation interval, retry count, VMPS IP addresses, and the current and primary servers.


clear vtp counters

Use the clear vtp counters privileged EXEC command on the switch stack or on a standalone switch to clear the VLAN Trunking Protocol (VTP) and pruning counters.

clear vtp counters

Syntax Description

This command has no arguments or keywords.

Defaults

No default is defined.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Examples

This example shows how to clear the VTP counters:

Switch# clear vtp counters

You can verify that information was deleted by entering the show vtp counters privileged EXEC command.

Related Commands

Command
Description

show vtp

Displays general information about the VTP management domain, status, and counters.


cluster commander-address

You do not need to enter this command from the switch stack or from a standalone cluster member switch. The cluster command switch automatically provides its MAC address to cluster member switches when these switches join the cluster. The cluster member switch adds this information and other cluster information to its running configuration file. Use the no form of this global configuration command from the cluster member switch console port or Ethernet management port to remove the switch from a cluster only during debugging or recovery procedures.

cluster commander-address mac-address [member number name name]

no cluster commander-address

Syntax Description

mac-address

MAC address of the cluster command switch.

member number

(Optional) Number of a configured cluster member switch. The range is 0 to 15.

name name

(Optional) Name of the configured cluster up to 31 characters.


Defaults

The switch is not a member of any cluster.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

This command is available only on the cluster command switch stack or the cluster command switch.

A cluster member can have only one cluster command switch.

The cluster member switch retains the identity of the cluster command switch during a system reload by using the mac-address parameter.

You can enter the no form on a cluster member switch to remove it from the cluster during debugging or recovery procedures. You would normally use this command from the cluster member switch console port or Ethernet management port only when the member has lost communication with the cluster command switch. With normal switch configuration, we recommend that you remove cluster member switches only by entering the no cluster member n global configuration command on the cluster command switch.

When a standby cluster command switch becomes active (becomes the cluster command switch), it removes the cluster commander address line from its configuration.

Examples

This is partial sample output from the running configuration of a cluster member.

Switch(config)# show running-configuration

<output truncated>

cluster commander-address 00e0.9bc0.a500 member 4 name my_cluster

<output truncated>

This example shows how to remove a member from the cluster by using the cluster member console.

Switch # configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# no cluster commander-address

You can verify your settings by entering the show cluster privileged EXEC command.

Related Commands

Command
Description

show cluster

Displays the cluster status and a summary of the cluster to which the switch belongs.


cluster discovery hop-count

Use the cluster discovery hop-count global configuration command on the switch stack or on the cluster command switch to set the hop-count limit for extended discovery of candidate switches. Use the no form of this command to return to the default setting.

cluster discovery hop-count number

no cluster discovery hop-count

Syntax Description

number

Number of hops from the cluster edge that the cluster command switch limits the discovery of candidates. The range is 1 to 7.


Defaults

The hop count is set to 3.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

This command is available only on the cluster command switch stack or cluster command switch. This command does not operate on cluster member switches.

If the hop count is set to 1, it disables extended discovery. The cluster command switch discovers only candidates that are one hop from the edge of the cluster. The edge of the cluster is the point between the last discovered cluster member switch and the first discovered candidate switch.

Examples

This example shows how to set hop count limit to 4. This command is executed on the cluster command switch.

Switch(config)# cluster discovery hop-count 4

You can verify your setting by entering the show cluster privileged EXEC command.

Related Commands

Command
Description

show cluster

Displays the cluster status and a summary of the cluster to which the switch belongs.

show cluster candidates

Displays a list of candidate switches.


cluster enable

Use the cluster enable global configuration command on a command-capable switch or switch stack to enable it as the cluster command switch, assign a cluster name, and to optionally assign a member number to it. Use the no form of the command to remove all members and to make the cluster command switch a candidate switch.

cluster enable name [command-switch-member-number]

no cluster enable

Syntax Description

name

Name of the cluster up to 31 characters. Valid characters include only alphanumerics, dashes, and underscores.

command-switch-member-number

(Optional) Assign a member number to the cluster command switch of the cluster. The range is 0 to 15.


Defaults

The switch is not a cluster command switch.

No cluster name is defined.

The member number is 0 when the switch is the cluster command switch.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Enter this command on any command-capable switch that is not part of any cluster. This command fails if a device is already configured as a member of the cluster.

You must name the cluster when you enable the cluster command switch. If the switch is already configured as the cluster command switch, this command changes the cluster name if it is different from the previous cluster name.

Examples

This example shows how to enable the cluster command switch, name the cluster, and set the cluster command switch member number to 4.

Switch(config)# cluster enable Engineering-IDF4 4

You can verify your setting by entering the show cluster privileged EXEC command on the cluster command switch.

Related Commands

Command
Description

show cluster

Displays the cluster status and a summary of the cluster to which the switch belongs.


cluster holdtime

Use the cluster holdtime global configuration command on the switch stack or on the cluster command switch to set the duration in seconds before a switch (either the command or cluster member switch) declares the other switch down after not receiving heartbeat messages. Use the no form of this command to set the duration to the default value.

cluster holdtime holdtime-in-secs

no cluster holdtime

Syntax Description

holdtime-in-secs

Duration in seconds before a switch (either a command or cluster member switch) declares the other switch down. The range is 1 to 300 seconds.


Defaults

The default holdtime is 80 seconds.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Enter this command with the cluster timer global configuration command only on the cluster command switch. The cluster command switch propagates the values to all its cluster members so that the setting is consistent among all switches in the cluster.

The holdtime is typically set as a multiple of the interval timer (cluster timer). For example, it takes (holdtime-in-secs divided by the interval-in-secs) number of heartbeat messages to be missed in a row to declare a switch down.

Examples

This example shows how to change the interval timer and the duration on the cluster command switch.

Switch(config)# cluster timer 3
Switch(config)# cluster holdtime 30

You can verify your settings by entering the show cluster privileged EXEC command.

Related Commands

Command
Description

show cluster

Displays the cluster status and a summary of the cluster to which the switch belongs.


cluster member

Use the cluster member global configuration command on the cluster command switch to add candidates to a cluster. Use the no form of the command to remove members from the cluster.

cluster member [n] mac-address H.H.H [password enable-password] [vlan vlan-id]

no cluster member n

Syntax Description

n

The number that identifies a cluster member. The range is 0 to 15.

mac-address H.H.H

MAC address of the cluster member switch in hexadecimal format.

password enable-password

Enable password of the candidate switch. The password is not required if there is no password on the candidate switch.

vlan vlan-id

(Optional) VLAN ID through which the candidate is added to the cluster by the cluster command switch. The range is 1 to 4094.


Defaults

A newly enabled cluster command switch has no associated cluster members.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Enter this command only on the cluster command switch to add a candidate to or remove a member from the cluster. If you enter this command on a switch other than the cluster command switch, the switch rejects the command and displays an error message.

You must enter a member number to remove a switch from the cluster. However, you do not need to enter a member number to add a switch to the cluster. The cluster command switch selects the next available member number and assigns it to the switch that is joining the cluster.

You must enter the enable password of the candidate switch for authentication when it joins the cluster. The password is not saved in the running or startup configuration. After a candidate switch becomes a member of the cluster, its password becomes the same as the cluster command-switch password.

If a switch does not have a configured hostname, the cluster command switch appends a member number to the cluster command-switch hostname and assigns it to the cluster member switch.

If you do not specify a VLAN ID, the cluster command switch automatically chooses a VLAN and adds the candidate to the cluster.

Examples

This example shows how to add a switch as member 2 with MAC address 00E0.1E00.2222 and the password key to a cluster. The cluster command switch adds the candidate to the cluster through VLAN 3.

Switch(config)# cluster member 2 mac-address 00E0.1E00.2222 password key vlan 3

This example shows how to add a switch with MAC address 00E0.1E00.3333 to the cluster. This switch does not have a password. The cluster command switch selects the next available member number and assigns it to the switch that is joining the cluster.

Switch(config)# cluster member mac-address 00E0.1E00.3333

You can verify your settings by entering the show cluster members privileged EXEC command on the cluster command switch.

Related Commands

Command
Description

show cluster

Displays the cluster status and a summary of the cluster to which the switch belongs.

show cluster candidates

Displays a list of candidate switches.

show cluster members

Displays information about the cluster members.


cluster outside-interface

Use the cluster outside-interface global configuration command on the switch stack or on the a cluster command switch to configure the outside interface for cluster Network Address Translation (NAT) so that a member without an IP address can communicate with devices outside the cluster. Use the no form of this command to return to the default setting.

cluster outside-interface interface-id

no cluster outside-interface

Syntax Description

interface-id

Interface to serve as the outside interface. Valid interfaces include physical interfaces, port-channels, or VLANs. The port-channel range is 1 to 48. The VLAN range is 1 to 4094.


Defaults

The default outside interface is automatically selected by the cluster command switch.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Enter this command only on the cluster command switch. If you enter this command on a cluster member switch, an error message appears.

Examples

This example shows how to set the outside interface to VLAN 1:

Switch(config)# cluster outside-interface vlan 1

You can verify your setting by entering the show running-config privileged EXEC command.

Related Commands

Command
Description

show running-config

Displays the operating configuration. For syntax information, use this link to the Cisco IOS Release 12.2 Command Reference listing page: http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/prod_command_reference_list.html
Select the Cisco IOS Commands Master List, Release 12.2 to navigate to the command.


cluster run

Use the cluster run global configuration command to enable clustering on a switch. Use the no form of this command to disable clustering on a switch.

cluster run

no cluster run

Syntax Description

This command has no arguments or keywords.

Defaults

Clustering is enabled on all switches.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

When you enter the no cluster run command on a cluster command switch or cluster command switch stack, the cluster command switch is disabled. Clustering is disabled, and the switch cannot become a candidate switch.

When you enter the no cluster run command on a cluster member switch, it is removed from the cluster. Clustering is disabled, and the switch cannot become a candidate switch.

When you enter the no cluster run command on a switch that is not part of a cluster, clustering is disabled on this switch. This switch cannot then become a candidate switch.

Examples

This example shows how to disable clustering on the cluster command switch:

Switch(config)# no cluster run

You can verify your setting by entering the show cluster privileged EXEC command.

Related Commands

Command
Description

show cluster

Displays the cluster status and a summary of the cluster to which the switch belongs.


cluster standby-group

Use the cluster standby-group global configuration command to enable cluster command-switch redundancy by binding the cluster to an existing Hot Standby Router Protocol (HSRP). Entering the routing-redundancy keyword enables the same HSRP group to be used for cluster command-switch redundancy and routing redundancy. Use the no form of this command to return to the default setting.

cluster standby-group HSRP-group-name [routing-redundancy]

no cluster standby-group

Syntax Description

HSRP-group-name

Name of the HSRP group that is bound to the cluster. The group name is limited to 32 characters.

routing-redundancy

(Optional) Enable the same HSRP standby group to be used for cluster command-switch redundancy and routing redundancy.


Defaults

The cluster is not bound to any HSRP group.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Enter this command only on the cluster command switch. If you enter it on a cluster member switch, an error message appears.

The cluster command switch propagates the cluster-HSRP binding information to all cluster-HSRP capable members. Each cluster member switch stores the binding information in its NVRAM. The HSRP group name must be a valid standby group; otherwise, the command exits with an error.

The same group name should be used on all members of the HSRP standby group that is to be bound to the cluster. The same HSRP group name should also be used on all cluster-HSRP capable members for the HSRP group that is to be bound. (When not binding a cluster to an HSRP group, you can use different names on the cluster commander and the members.)

Examples

This example shows how to bind the HSRP group named my_hsrp to the cluster. This command is executed on the cluster command switch.

Switch(config)# cluster standby-group my_hsrp 

This example shows how to use the same HSRP group named my_hsrp for routing redundancy and cluster redundancy.

Switch(config)# cluster standby-group my_hsrp routing-redundancy

This example shows the error message when this command is executed on a cluster command switch and the specified HSRP standby group does not exist:

Switch(config)# cluster standby-group my_hsrp 
%ERROR: Standby (my_hsrp) group does not exist

This example shows the error message when this command is executed on a cluster member switch:

Switch(config)# cluster standby-group my_hsrp routing-redundancy
%ERROR: This command runs on a cluster command switch

You can verify your settings by entering the show cluster privileged EXEC command. The output shows whether redundancy is enabled in the cluster.

Related Commands

Command
Description

standby ip

Enables HSRP on the interface. For syntax information, select Cisco IOS IP Command Reference, Volume 1 of 3:Addressing and Services, Release 12.2 > IP Services Commands.

show cluster

Displays the cluster status and a summary of the cluster to which the switch belongs.

show standby

Displays standby group information. For syntax information, select Cisco IOS IP Command Reference, Volume 1 of 3:Addressing and Services, Release 12.2 > IP Services Commands.


cluster timer

Use the cluster timer global configuration command on the switch stack or on the a cluster command switch to set the interval in seconds between heartbeat messages. Use the no form of this command to set the interval to the default value.

cluster timer interval-in-secs

no cluster timer

Syntax Description

interval-in-secs

Interval in seconds between heartbeat messages. The range is 1 to 300 seconds.


Defaults

The interval is 8 seconds.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Enter this command with the cluster holdtime global configuration command only on the cluster command switch. The cluster command switch propagates the values to all its cluster members so that the setting is consistent among all switches in the cluster.

The holdtime is typically set as a multiple of the heartbeat interval timer (cluster timer). For example, it takes (holdtime-in-secs divided by the interval-in-secs) number of heartbeat messages to be missed in a row to declare a switch down.

Examples

This example shows how to change the heartbeat interval timer and the duration on the cluster command switch:

Switch(config)# cluster timer 3
Switch(config)# cluster holdtime 30

You can verify your settings by entering the show cluster privileged EXEC command.

Related Commands

Command
Description

show cluster

Displays the cluster status and a summary of the cluster to which the switch belongs.


copy logging onboard

Use the copy logging onboard privileged EXEC command on the switch stack or on a standalone switch to copy on-board failure logging (OBFL) data to the local network or a specific file system.

copy logging onboard module stack-member destination

Syntax Description

module stack-member

Specify the stack member number. If the switch is a standalone switch, the switch number is 1. If the switch is in a stack, the range is 1 to 9, depending on the switch member numbers in the stack.

This keyword is supported only on on stacking-capable switches.

destination

Specify the location on the local network or file system to which the system messages are copied.

For destination, specify the destination on the local or network file system and the filename. These options are supported:

The syntax for the local flash file system:
flash[number]:/filename

Use the number parameter to specify the stack member number of the stack master. The range for number is 1 to 9.

The syntax for the FTP:
ftp://username:password@host/filename

The syntax for an HTTP server:
http://[[username:password]@]{hostname | host-ip}[/directory]/filename

The syntax for the NVRAM:
nvram:/filename

The syntax for the null file system:
null:/filename

The syntax for the Remote Copy Protocol (RCP): rcp://username@host/filename

The syntax for the switch file system:
system:filename

The syntax for the temporary file system:
tmpsys:/filename

The syntax for the TFTP:
tftp:[[//location]/directory]/filename


Defaults

This command has no default setting.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

For information about OBFL, see the hw-module command.

Examples

This example shows how to copy the OBFL data messages to the obfl_file file on the flash file system for stack member 3:

Switch# copy logging onboard module 3 flash:obfl_file
OBFL copy successful
Switch#

Related Commands

Command
Description

hw-module module [switch-number] logging onboard

Enables OBFL.

show logging onboard onboard

Displays OBFL information.


confidentiality-offset

To configure the confidentiality offset value for the MACsec Key Agreement (MKA) Protocol policy, use the confidentiality-offset MKA policy configuration command. To return to the default setting, use the no or default form of this command

confidentiality-offset offset-value

[no | default] confidentiality-offset

Syntax Description

offset-value

Identifies a confidentiality (encryption) offset value for the MKA policy. Valid values are 0, 30, and 50 octets (bytes).


Defaults

The default offset is 0 with no confidentiality offset.

Command Modes

MKA policy configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

If no confidentiality offset is configured, no encryption offset is used.

To use this feature, both peers must support confidentiality offset.

Examples

This example configures an MKA policy with a confidentiality offset of 30 bytes.

Switch(config)# mka policy replay-policy
Switch(config-mka-policy)# replay-protection window-size 300
Switch(config-mka-policy)# confidentiality offset 30
Switch(config-mka-policy)# end

You can verify your setting by entering the show mka session detail privileged EXEC command.

Related Commands

Command
Description

show mka session detail

Displays detailed information about active MKA sessions.


define interface-range

Use the define interface-range global configuration command on the switch stack or on a standalone switch to create an interface-range macro. Use the no form of this command to delete the defined macro.

define interface-range macro-name interface-range

no define interface-range macro-name interface-range

Syntax Description

macro-name

Name of the interface-range macro; up to 32 characters.

interface-range

Interface range; for valid values for interface ranges, see "Usage Guidelines."


Defaults

This command has no default setting.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

The macro name is a 32-character maximum character string.

A macro can contain up to five ranges.

All interfaces in a range must be the same type; that is, all Fast Ethernet ports, all Gigabit Ethernet ports, all EtherChannel ports, or all VLANs, but you can combine multiple interface types in a macro.

When entering the interface-range, use this format:

type {first-interface} - {last-interface}

You must add a space between the first interface number and the hyphen when entering an interface-range. For example, gigabitethernet 1/0/1 - 2 is a valid range; gigabitethernet 1/0/1-2 is not a valid range

Valid values for type and interface:

vlan vlan-id - vlan-ID, where the VLAN ID is 1 to 4094

VLAN interfaces must have been configured with the interface vlan command (the show running-config privileged EXEC command displays the configured VLAN interfaces). VLAN interfaces not displayed by the show running-config command cannot be used in interface-ranges.

port-channel port-channel-number, where port-channel-number is from 1 to 48

gigabitethernet stack member/module/{first port} - {last port}

tengigabitethernet stack member/module/{first port} - {last port}

For physical interfaces:

stack member is the number used to identify the switch within the stack. The number ranges from 1 to 9 and is assigned to the switch the first time the stack member initializes.

module is always 0.

the range is type stack member/0/number - number (for example, gigabitethernet 1/0/1 - 2).

When you define a range, you must enter a space before the hyphen (-), for example:

gigabitethernet1/0/1 - 2

You can also enter multiple ranges. When you define multiple ranges, you must enter a space after the first entry before the comma (,). The space after the comma is optional, for example:

gigabitethernet1/0/3, gigabitethernet2/0/1 - 2

gigabitethernet1/0/3 -4, tengigabitethernet1/0/1 - 2

Examples

This example shows how to create a multiple-interface macro:

Switch(config)# define interface-range macro1 gigabitethernet1/0/1 - 2, 
gigabitethernet1/0/5 - 7, gigabitethernet3/0/2 - 4, tengigabitethernet1/0/1 - 2

Related Commands

Command
Description

interface range

Executes a command on multiple ports at the same time.

show running-config

Displays the operating configuration. For syntax information, use this link to the Cisco IOS Release 12.2 Command Reference listing page: http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/prod_command_reference_list.html
Select the Cisco IOS Commands Master List, Release 12.2 to navigate to the command.


delete

Use the delete privileged EXEC command on the switch stack or on a standalone switch to delete a file or directory on the flash memory device.

delete [/force] [/recursive] filesystem:/file-url

Syntax Description

/force

(Optional) Suppress the prompt that confirms the deletion.

/recursive

(Optional) Delete the named directory and all subdirectories and the files contained in it.

filesystem:

Alias for a flash file system.

The syntax for the local flash file system on the stack member or the stack master:
flash:

From the stack master, the syntax for the local flash file system on a stack member:
flash member number:

/file-url

The path (directory) and filename to delete.


Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

If you use the /force keyword, you are prompted once at the beginning of the deletion process to confirm the deletion.

If you use the /recursive keyword without the /force keyword, you are prompted to confirm the deletion of every file.

The prompting behavior depends on the setting of the file prompt global configuration command. By default, the switch prompts for confirmation on destructive file operations. For more information about this command, see the Cisco IOS Configuration Fundamentals Command Reference, Release 12.2.

Examples

This example shows how to remove the directory that contains the old software image after a successful download of a new image:

Switch# delete /force /recursive flash:/old-image

You can verify that the directory was removed by entering the dir filesystem: privileged EXEC command.

Related Commands

Command
Description

archive download-sw

Downloads a new image to the switch and overwrites or keeps the existing image.


deny (ARP access-list configuration)

Use the deny Address Resolution Protocol (ARP) access-list configuration command on the switch stack or on a standalone switch to deny an ARP packet based on matches against the DHCP bindings. Use the no form of this command to remove the specified access control entry (ACE) from the access list.

deny {[request] ip {any | host sender-ip | sender-ip sender-ip-mask} mac {any | host sender-mac | sender-mac sender-mac-mask} | response ip {any | host sender-ip | sender-ip sender-ip-mask} [{any | host target-ip | target-ip target-ip-mask}] mac {any | host sender-mac | sender-mac sender-mac-mask} [{any | host target-mac | target-mac target-mac-mask}]} [log]

no deny {[request] ip {any | host sender-ip | sender-ip sender-ip-mask} mac {any | host sender-mac | sender-mac sender-mac-mask} | response ip {any | host sender-ip | sender-ip sender-ip-mask} [{any | host target-ip | target-ip target-ip-mask}] mac {any | host sender-mac | sender-mac sender-mac-mask} [{any | host target-mac | target-mac target-mac-mask}]} [log]

This command is available only if your switch is running the IP services feature set.

Syntax Description

request

(Optional) Define a match for the ARP request. When request is not specified, matching is performed against all ARP packets.

ip

Specify the sender IP address.

any

Deny any IP or MAC address.

host sender-ip

Deny the specified sender IP address.

sender-ip sender-ip-mask

Deny the specified range of sender IP addresses.

mac

Deny the sender MAC address.

host sender-mac

Deny a specific sender MAC address.

sender-mac sender-mac-mask

Deny the specified range of sender MAC addresses.

response ip

Define the IP address values for the ARP responses.

host target-ip

Deny the specified target IP address.

target-ip target-ip-mask

Deny the specified range of target IP addresses.

mac

Deny the MAC address values for the ARP responses.

host target-mac

Deny the specified target MAC address.

target-mac target-mac-mask

Deny the specified range of target MAC addresses.

log

(Optional) Log a packet when it matches the ACE.


Defaults

There are no default settings. However, at the end of the ARP access list, there is an implicit deny ip any mac any command.

Command Modes

ARP access-list configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You can add deny clauses to drop ARP packets based on matching criteria.

Examples

This example shows how to define an ARP access list and to deny both ARP requests and ARP responses from a host with an IP address of 1.1.1.1 and a MAC address of 0000.0000.abcd:

Switch(config)# arp access-list static-hosts
Switch(config-arp-nacl)# deny ip host 1.1.1.1 mac host 0000.0000.abcd
Switch(config-arp-nacl)# end

You can verify your settings by entering the show arp access-list privileged EXEC command.

Related Commands

Command
Description

arp access-list

Defines an ARP access control list (ACL).

ip arp inspection filter vlan

Permits ARP requests and responses from a host configured with a static IP address.

permit (ARP access-list configuration)

Permits an ARP packet based on matches against the DHCP bindings.

show arp access-list

Displays detailed information about ARP access lists.


deny (IPv6 access-list configuration)

Use the deny command in IPv6 access list configuration mode on the switch stack or on a standalone switch to set deny conditions for an IPv6 access list. Use the no form of this command to remove the deny conditions.

deny {protocol} {source-ipv6-prefix/prefix-length | any | host source-ipv6-address} [operator [port-number]] {destination-ipv6-prefix/prefix-length | any | host destination-ipv6-address} [operator [port-number]] [dscp value] [fragments] [log] [log-input] [routing] [sequence value] [time-range name]

no deny {protocol} {source-ipv6-prefix/prefix-length | any | host source-ipv6-address} [operator [port-number]] {destination-ipv6-prefix/prefix-length | any | host destination-ipv6-address} [operator [port-number]] [dscp value] [fragments] [log] [log-input] [routing] [sequence value] [time-range name]

Internet Control Message Protocol

deny icmp {source-ipv6-prefix/prefix-length | any | host source-ipv6-address} [operator [port-number]] {destination-ipv6-prefix/prefix-length | any | host destination-ipv6-address} [operator [port-number]] [icmp-type [icmp-code] | icmp-message] [dscp value] [log] [log-input] [routing] [sequence value] [time-range name]

Transmission Control Protocol

deny tcp {source-ipv6-prefix/prefix-length | any | host source-ipv6-address} [operator [port-number]] {destination-ipv6-prefix/prefix-length | any | host destination-ipv6-address} [operator [port-number]] [ack] [dscp value] [established] [fin] [log] [log-input] [neq {port | protocol}] [psh] [range {port | protocol}] [rst] [routing] [sequence value] [syn] [time-range name] [urg]

User Datagram Protocol

deny udp {source-ipv6-prefix/prefix-length | any | host source-ipv6-address} [operator [port-number]] {destination-ipv6-prefix/prefix-length | any | host destination-ipv6-address} [operator [port-number]] [dscp value] [log] [log-input] [neq {port | protocol}] [range {port | protocol}] [routing] [sequence value] [time-range name]


Note This command is available only if you have configured a dual IPv4 and IPv6 Switch Database Management (SDM) template on the switch. This command is not supported on switches running the LAN base feature set.


Syntax Description

protocol

Name or number of an Internet protocol. It can be one of the keywords ahp, esp, icmp, ipv6, pcp, sctp, tcp, or udp, or an integer in the range from 0 to 255 representing an IPv6 protocol number.

source-ipv6-prefix/prefix-length

The source IPv6 network or class of networks about which to set deny conditions.

This argument must be in the form documented in RFC 2373 where the address is specified in hexadecimal using 16-bit values between colons.

any

An abbreviation for the IPv6 prefix ::/0.

host source-ipv6-address

The source IPv6 host address for which to set deny conditions.

This source-ipv6-address argument must be in the form documented in RFC 2373 where the address is specified in hexadecimal using 16-bit values between colons.

operator [port-number]

(Optional) Specify an operator that compares the source or destination ports of the specified protocol. Operators are lt (less than), gt (greater than), eq (equal), neq (not equal), and range (inclusive range).

If the operator is positioned after the source-ipv6-prefix/prefix-length argument, it must match the source port.

If the operator is positioned after the destination-ipv6-prefix/prefix-length argument, it must match the destination port.

The range operator requires two port numbers. All other operators require one port number.

The optional port-number argument is a decimal number or the name of a TCP or a UDP port. A port number is a number from 0 to 65535. TCP port names can be used only when filtering TCP. UDP port names can be used only when filtering UDP.

destination-ipv6-prefix/
prefix-length

The destination IPv6 network or class of networks for which to set deny conditions.

This argument must be in the form documented in RFC 2373 where the address is specified in hexadecimal using 16-bit values between colons.

host destination-ipv6-address

The destination IPv6 host address for which to set deny conditions.

This destination-ipv6-address argument must be in the form documented in RFC 2373 where the address is specified in hexadecimal using 16-bit values between colons.

dscp value

(Optional) Match a differentiated services code point value against the traffic class value in the Traffic Class field of each IPv6 packet header. The acceptable range is from 0 to 63.

fragments

(Optional) Match non-initial fragmented packets where the fragment extension header contains a non-zero fragment offset. The fragments keyword is an option only if the protocol is ipv6 and the operator [port-number] arguments are not specified.

log

(Optional) Send an informational logging message to the console about the packet that matches the entry. (The level of messages sent to the console is controlled by the logging console command.)

The message includes the access list name and sequence number, whether the packet was denied; the protocol, whether it was TCP, UDP, ICMP, or a number; and, if appropriate, the source and destination addresses and source and destination port numbers. The message is generated for the first packet that matches, and then at 5-minute intervals, including the number of packets denied in the prior 5-minute interval.

Note Logging is not supported for port ACLs.

log-input

(Optional) Provide the same function as the log keyword, but the logging message also includes the receiving interface.

routing

(Optional) Match packets with the routing extension header.

sequence value

(Optional) Specify the sequence number for the access list statement. The acceptable range is from 1 to 4294967295.

time-range name

(Optional) Specify the time range that applies to the deny statement. The name of the time range and its restrictions are specified by the time-range and absolute or periodic commands, respectively.

icmp-type

(Optional) Specify an ICMP message type for filtering ICMP packets. ICMP packets can be filtered by an ICMP message type. The type is a number from 0 to 255.

icmp-code

(Optional) Specify an ICMP message code for filtering ICMP packets. ICMP packets that are filtered by ICMP message type can also be filtered by the ICMP message code. The code is a number from 0 to 255.

icmp-message

(Optional) Specify an ICMP message name for filtering ICMP packets. ICMP packets can be filtered by an ICMP message name or an ICMP message type and code. The possible names are listed in the "Usage Guidelines" section.

ack

(Optional) Only for the TCP protocol: Acknowledgment (ACK) bit set.

established

(Optional) Only for the TCP protocol: Means the connection has been established. A match occurs if the TCP datagram has the ACK or RST bits set. The nonmatching case is that of the initial TCP datagram to form a connection.

fin

(Optional) Only for the TCP protocol: Fin bit set; no more data from sender.

neq {port | protocol}

(Optional) Match only packets that are not on a given port number.

psh

(Optional) Only for the TCP protocol: Push function bit set.

range {port | protocol}

(Optional) Match only packets in the range of port numbers.

rst

(Optional) Only for the TCP protocol: Reset bit set.

syn

(Optional) Only for the TCP protocol: Synchronize bit set.

urg

(Optional) Only for the TCP protocol: Urgent pointer bit set.



Note Although visible in the command-line help strings, the flow-label, routing, and undetermined-transport keywords are not supported.


Defaults

No IPv6 access list is defined.

Command Modes

IPv6 access list configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

The deny (IPv6 access-list configuration mode) command is similar to the deny (IPv4 access-list configuration mode) command, but it is IPv6-specific.

Use the deny (IPv6) command after the ipv6 access-list command to enter IPv6 access list configuration mode and to define the conditions under which a packet passes the access list.

Specifying IPv6 for the protocol argument matches against the IPv6 header of the packet.

By default, the first statement in an access list is number 10, and the subsequent statements are numbered in increments of 10.

You can add permit, deny, or remark statements to an existing access list without re-entering the entire list. To add a new statement anywhere other than at the end of the list, create a new statement with an appropriate entry number between two existing entry numbers to show where it belongs.


Note Every IPv6 ACL has implicit permit icmp any any nd-na, permit icmp any any nd-ns, and deny ipv6 any any statements as its last match conditions. The two permit conditions allow ICMPv6 neighbor discovery. To disallow ICMPv6 neighbor discovery and to deny icmp any any nd-na or icmp any any nd-ns, there must be an explicit deny entry in the ACL. For the three implicit statements to take effect, an IPv6 ACL must contain at least one entry.

The IPv6 neighbor discovery process uses the IPv6 network layer service. Therefore, by default, IPv6 ACLs implicitly allow IPv6 neighbor discovery packets to be sent and received on an interface. In IPv4, the Address Resolution Protocol (ARP), which is equivalent to the IPv6 neighbor discovery process, uses a separate data-link layer protocol. Therefore, by default, IPv4 ACLs implicitly allow ARP packets to be sent and received on an interface.


Both the source-ipv6-prefix/prefix-length and destination-ipv6-prefix/prefix-length arguments are used for traffic filtering. (The source prefix filters traffic based upon the traffic source; the destination prefix filters traffic based upon the traffic destination.)

The switch supports IPv6 address matching for a full range of prefix-lengths.

The fragments keyword is an option only if the protocol is ipv6 and the operator [port-number] arguments are not specified.

This is a list of ICMP message names:

beyond-scope

destination-unreachable

echo-reply

echo-request

header

hop-limit

mld-query

mld-reduction

mld-report

nd-na

nd-ns

next-header

no-admin

no-route

packet-too-big

parameter-option

parameter-problem

port-unreachable

reassembly-timeout

renum-command

renum-result

renum-seq-number

router-advertisement

router-renumbering

router-solicitation

time-exceeded

unreachable

 

Examples

This example configures the IPv6 access list named CISCO and applies the access list to outbound traffic on a Layer 3 interface. The first deny entry in the list prevents all packets that have a destination TCP port number greater than 5000 from leaving the interface. The second deny entry in the list prevents all packets that have a source UDP port number less than 5000 from leaving the interface. The second deny also logs all matches to the console. The first permit entry in the list permits all ICMP packets to leave the interface. The second permit entry in the list permits all other traffic to leave the interface. The second permit entry is necessary because an implicit deny-all condition is at the end of each IPv6 access list.

Switch(config)# ipv6 access-list CISCO
Switch(config-ipv6-acl)# deny tcp any any gt 5000
Switch config-ipv6-acl)# deny ::/0 lt 5000 ::/0 log
Switch(config-ipv6-acl)# permit icmp any any
Switch(config-ipv6-acl)# permit any any
Switch(config-ipv6-acl)# exit
Switch(config)# interface gigabitethernet1/0/3
Switch(config-if)# no switchport
Switch(config-if)# ipv6 address 2001::/64 eui-64
Switch(config-if)# ipv6 traffic-filter CISCO out

Related Commands

Command
Description

ipv6 access-list

Defines an IPv6 access list and enters IPv6 access list configuration mode.

ipv6 traffic-filter

Filters incoming or outgoing IPv6 traffic on an interface.

permit (IPv6 access-list configuration)

Sets permit conditions for an IPv6 access list.

show ipv6 access-list

Displays the contents of all current IPv6 access lists.


deny (MAC access-list configuration)

Use the deny MAC access-list configuration command on the switch stack or on a standalone switch to prevent non-IP traffic from being forwarded if the conditions are matched. Use the no form of this command to remove a deny condition from the named MAC access list.

{deny | permit} {any | host src-MAC-addr | src-MAC-addr mask} {any | host dst-MAC-addr | dst-MAC-addr mask} [type mask | aarp | amber | cos cos | dec-spanning | decnet-iv | diagnostic | dsm | etype-6000 | etype-8042 | lat | lavc-sca | lsap lsap mask | mop-console | mop-dump | msdos | mumps | netbios | vines-echo | vines-ip | xns-idp]

no {deny | permit} {any | host src-MAC-addr | src-MAC-addr mask} {any | host dst-MAC-addr | dst-MAC-addr mask} [type mask | aarp | amber | cos cos | dec-spanning | decnet-iv | diagnostic | dsm | etype-6000 | etype-8042 | lat | lavc-sca | lsap lsap mask | mop-console | mop-dump | msdos | mumps | netbios | vines-echo | vines-ip | xns-idp]

Syntax Description

any

Keyword to specify to deny any source or destination MAC address.

host src MAC-addr |
src-MAC-addr mask

Define a host MAC address and optional subnet mask. If the source address for a packet matches the defined address, non-IP traffic from that address is denied.

host dst-MAC-addr |
dst-MAC-addr mask

Define a destination MAC address and optional subnet mask. If the destination address for a packet matches the defined address, non-IP traffic to that address is denied.

type mask

(Optional) Use the Ethertype number of a packet with Ethernet II or SNAP encapsulation to identify the protocol of the packet.

The type is 0 to 65535, specified in hexadecimal.

The mask is a mask of don't care bits applied to the Ethertype before testing for a match.

aarp

(Optional) Select Ethertype AppleTalk Address Resolution Protocol that maps a data-link address to a network address.

amber

(Optional) Select EtherType DEC-Amber.

cos cos

(Optional) Select a class of service (CoS) number from 0 to 7 to set priority. Filtering on CoS can be performed only in hardware. A warning message reminds the user if the cos option is configured.

dec-spanning

(Optional) Select EtherType Digital Equipment Corporation (DEC) spanning tree.

decnet-iv

(Optional) Select EtherType DECnet Phase IV protocol.

diagnostic

(Optional) Select EtherType DEC-Diagnostic.

dsm

(Optional) Select EtherType DEC-DSM.

etype-6000

(Optional) Select EtherType 0x6000.

etype-8042

(Optional) Select EtherType 0x8042.

lat

(Optional) Select EtherType DEC-LAT.

lavc-sca

(Optional) Select EtherType DEC-LAVC-SCA.

lsap lsap-number mask

(Optional) Use the LSAP number (0 to 65535) of a packet with 802.2 encapsulation to identify the protocol of the packet.

mask is a mask of don't care bits applied to the LSAP number before testing for a match.

mop-console

(Optional) Select EtherType DEC-MOP Remote Console.

mop-dump

(Optional) Select EtherType DEC-MOP Dump.

msdos

(Optional) Select EtherType DEC-MSDOS.

mumps

(Optional) Select EtherType DEC-MUMPS.

netbios

(Optional) Select EtherType DEC- Network Basic Input/Output System (NETBIOS).

vines-echo

(Optional) Select EtherType Virtual Integrated Network Service (VINES) Echo from Banyan Systems.

vines-ip

(Optional) Select EtherType VINES IP.

xns-idp

(Optional) Select EtherType Xerox Network Systems (XNS) protocol suite (0 to 65535), an arbitrary Ethertype in decimal, hexadecimal, or octal.



Note Though visible in the command-line help strings, appletalk is not supported as a matching condition.


To filter IPX traffic, you use the type mask or lsap lsap mask keywords, depending on the type of IPX encapsulation being used. Filter criteria for IPX encapsulation types as specified in Novell terminology and Cisco IOS terminology are listed in Table 2-4.

Table 2-4 IPX Filtering Criteria

IPX Encapsulation Type
Filter Criterion
Cisco IOS Name
Novel Name

arpa

Ethernet II

Ethertype 0x8137

snap

Ethernet-snap

Ethertype 0x8137

sap

Ethernet 802.2

LSAP 0xE0E0

novell-ether

Ethernet 802.3

LSAP 0xFFFF


Defaults

This command has no defaults. However; the default action for a MAC-named ACL is to deny.

Command Modes

MAC-access list configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You enter MAC-access list configuration mode by using the mac access-list extended global configuration command.

If you use the host keyword, you cannot enter an address mask; if you do not use the host keyword, you must enter an address mask.

When an access control entry (ACE) is added to an access control list, an implied deny-any-any condition exists at the end of the list. That is, if there are no matches, the packets are denied. However, before the first ACE is added, the list permits all packets.

For more information about named MAC extended access lists, see the software configuration guide for this release.

Examples

This example shows how to define the named MAC extended access list to deny NETBIOS traffic from any source to MAC address 00c0.00a0.03fa. Traffic matching this list is denied.

Switch(config-ext-macl)# deny any host 00c0.00a0.03fa netbios.

This example shows how to remove the deny condition from the named MAC extended access list:

Switch(config-ext-macl)# no deny any 00c0.00a0.03fa 0000.0000.0000 netbios.

This example denies all packets with Ethertype 0x4321:

Switch(config-ext-macl)# deny any any 0x4321 0

You can verify your settings by entering the show access-lists privileged EXEC command.

Related Commands

Command
Description

mac access-list extended

Creates an access list based on MAC addresses for non-IP traffic.

permit (MAC access-list configuration)

Permits non-IP traffic to be forwarded if conditions are matched.

show access-lists

Displays access control lists configured on a switch.


diagnostic monitor

Use the diagnostic monitor global configuration command to configure health-monitoring diagnostic testing. Use the no form of this command to disable testing and to return to the default settings.

diagnostic monitor interval switch number test {name | test-id | test-id-range | all} hh:mm:ss milliseconds day

diagnostic monitor switch number test {name | test-id | test-id-range | all}

diagnostic monitor syslog

diagnostic monitor threshold switch number test {name | test-id | test-id-range | all} failure count count

no diagnostic monitor interval switch number test {name | test-id | test-id-range | all}

no diagnostic monitor switch number test {name | test-id | test-id-range | all}

no diagnostic monitor syslog

no diagnostic monitor threshold switch number test {name | test-id | test-id-range | all} failure count count

Syntax Description

interval

Configure the interval between tests.

switch number

Specify the switch number, which is the stack member number. If the switch is a standalone switch, the switch number is 1. If the switch is in a stack, the range is 1 to 9, depending on the switch member numbers in the stack.

This keyword is supported only on on stacking-capable switches.

test

Specify the tests to be run.

name

Specify the name of the test. For more information, see the "Usage Guidelines" section.

test-id

Specify the ID number of the test. The range is from 1 to 7. For more information, see the "Usage Guidelines" section.

test-id-range

Specify more than one test with the range of test ID numbers. For more information, see the "Usage Guidelines" section.

all

Specify all of the diagnostic tests.

hh:mm:ss

Configure the monitoring interval in hours, minutes, and seconds. For formatting information, see the "Usage Guidelines" section.

milliseconds

Configure the monitoring interval in milliseconds (ms). The range is from 0 to 999 ms.

day

Configure the monitoring interval in the number of days. The range is from 0 to 20 days. For formatting information, see the "Usage Guidelines" section.

syslog

Enable the generation of a syslog message when a health-monitoring test fails.

threshold

Configure the failure threshold.

failure count count

Set the failure threshold count. The range for count is from 0 to 99.


Defaults

Monitoring is disabled, and a failure threshold value is not set.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Follow these guidelines when configuring health-monitoring diagnostic testing:

name—Enter the show diagnostic content privileged EXEC command to display the test names in the test ID list.

test-idEnter the show diagnostic content command to display the test numbers in the test ID list.

test-id-rangeEnter the show diagnostic content command to display the test numbers in the test ID list. Enter the range as integers separated by a comma and a hyphen (for example, 1,3-6 specifies test IDs 1, 3, 4, 5, and 6).

hh—Enter the hours from 0 to 24.

mm—Enter the minutes from 0 to 60.

ss—Enter the seconds from 0 to 60.

milliseconds—Enter the test time in milliseconds from 0 to 999.

day—Enter the number of days between test from 0 to 20.

Enter the diagnostic monitor test 1 command to enable diagnostic monitoring.

You must configure the failure threshold and the interval between tests before enabling diagnostic monitoring.

When entering the diagnostic monitor switch number test {name | test-id | test-id-range | all} command, you must isolate network traffic by disabling all connected ports, and do not send test packets during the test.

Examples

This example shows how to configure a health-monitoring test:

Switch(config)# diagnostic monitor threshold switch 2 test 1 failure count 20
Switch(config)# diagnostic monitor interval switch 2 test 1 12:30:00 750 5

Related Commands

Command
Description

show diagnostic

Displays online diagnostic test results.


diagnostic schedule

Use the diagnostic schedule global configuration command to configure the diagnostic test schedule. Use the no form of this command to remove the schedule.

diagnostic schedule switch number test {name | test-id | test-id-range | all | basic | non-disruptive} {daily hh:mm | on mm dd yyyy hh:mm | weekly day-of-week hh:mm}

no diagnostic schedule switch number test {name | test-id | test-id-range | all | basic | non-disruptive} {daily hh:mm | on mm dd yyyy hh:mm | weekly day-of-week hh:mm}

Syntax Description

switch number

Specify the switch number, which is the stack member number. If the switch is a standalone switch, the switch number is 1. If the switch is in a stack, the range is 1 to 9, depending on the switch member numbers in the stack.

This keyword is supported only on on stacking-capable switches.

test

Specify the tests to be scheduled.

name

Specify the name of the test. For more information, see the "Usage Guidelines" section.

test-id

Specify the ID number of the test. The range is from 1 to 7. For more information, see the "Usage Guidelines" section.

test-id-range

Specify more than one test with the range of test ID numbers. For more information, see the "Usage Guidelines" section.

all

Specify all of the diagnostic tests.

basic

Specify the basic on-demand diagnostic tests.

non-disruptive

Specify the nondisruptive health-monitoring tests.

daily hh:mm

Specify the daily scheduling of the diagnostic tests. For formatting information, see the "Usage Guidelines" section.

on mm dd yyyy hh:mm

Specify the scheduling of the diagnostic tests on a specific day and time. For formatting information, see the "Usage Guidelines" section.

weekly day-of-week hh:mm

Specify the weekly scheduling of the diagnostic tests. For formatting information, see the "Usage Guidelines" section.


Defaults

This command has no default settings.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Use these guidelines when scheduling testing:

name—Enter the show diagnostic content privileged EXEC command to display the test names in the test ID list.

test-idEnter the show diagnostic content command to display the test numbers in the test ID list.

test-id-rangeEnter the show diagnostic content command to display the test numbers in the test ID list. Enter the range as integers separated by a comma and a hyphen (for example, 1,3-6 specifies test IDs 1, 3, 4, 5, and 6).

hh:mm—Enter the time as a 2-digit number (for a 24-hour clock) for hours:minutes; the colon (:) is required, such as 12:30.

For mm dd yyyy:

mm—Spell out the month, such as January, February, and so on, with upper case or lower case characters.

dd—Enter the day as a 2-digit number, such as 03 or 16.

yyyy—Enter the year as a 4-digit number, such as 2006.

day-of-week—Spell out the day of the week, such as Monday, Tuesday, and so on, with upper case or lower case characters.


Note If you are running a diagnostic test that has the reload attribute on a switch in a stack, you could potentially partition the stack depending on your cabling configuration. To avoid partitioning your stack, enter the show switch detail privileged EXEC command to verify the stack configuration.


Examples

This example shows how to schedule diagnostic testing for a specific day and time on stack member 3 when this command is entered on a stack master:

Switch(config)# diagnostic schedule switch 3 test 1,2,4-6 on november 3 2006 23:10

This example shows how to schedule diagnostic testing to occur weekly at a specific time on a switch:

Switch(config)# diagnostic schedule test TestPortAsicMem weekly friday 09:23

Related Commands

Command
Description

show diagnostic

Displays online diagnostic test results.


diagnostic start

Use the diagnostic start privileged EXEC command to run an online diagnostic test.

diagnostic start switch number test {name | test-id | test-id-range | all | basic | non-disruptive}

Syntax Description

switch number

Specify the switch number, which is the stack member number. If the switch is a standalone switch, the switch number is 1. If the switch is in a stack, the range is 1 to 9, depending on the switch member numbers in the stack.

This keyword is supported only on on stacking-capable switches.

test

Specify the tests to run.

name

Specify the name of a test. For more information, see the "Usage Guidelines" section.

test-id

Specify the ID number of a test. The range is from 1 to 7. For more information, see the "Usage Guidelines" section.

test-id-range

Specify more than one test with the range of test ID numbers. For more information, see the "Usage Guidelines" section.

all

Specify all the diagnostic tests.

basic

Specify the basic on-demand diagnostic tests.

non-disruptive

Specify the nondisruptive health-monitoring tests.


Defaults

This command has no default setting.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

The switch supports these tests:

ID   Test Name [On-Demand Test Attributes]
---  -------------------------------------------
1    TestPortAsicStackPortLoopback    [B*N****]
2    TestPortAsicLoopback             [B*D*R**]
3    TestPortAsicCam                  [B*D*R**]
4    TestPortAsicRingLoopback         [B*D*R**]
5    TestMicRingLoopback              [B*D*R**]
6    TestPortAsicMem                  [B*D*R**]
7    TestInlinePwrCtlr                [B*D*R**]
---  -------------------------------------------

When specifying a test name, use the show diagnostic content privileged EXEC command to display the test ID list. To specify test 3 by using the test name, enter the diagnostic start switch number test TestPortAsicCam privileged EXEC command.

If specifying more than one test to run, use the test-id-range parameter, and enter integers separated by a comma and a hyphen. For example, to specify tests 2, 3, and 4, enter the diagnostic start switch number test 2-4 command. To specify tests 1, 3, 4, 5, and 6, enter the diagnostic start switch number test 1,3-6 command.

After starting the tests by using the diagnostic start command, you cannot stop the testing process.

Examples

This example shows how to start diagnostic test 1 on stack member 2 when this command is entered on a stack master:

Switch# diagnostic start switch 2 test 1
Switch#
06:27:50: %DIAG-6-TEST_RUNNING: Switch 2: Running TestPortAsicStackPortLoopback{ID=1} ...
(switch-1)
06:27:51: %DIAG-6-TEST_OK: Switch 2: TestPortAsicStackPortLoopback{ID=1} has completed
successfully (switch-2)

This example shows how to start diagnostic test 2 on a stack member in a switch stack. Running this test disrupts the normal system operation, causes the switch to lose stack connectivity, and then causes the switch to reload.

Switch# diagnostic start switch 1 test 2
Switch 1: Running test(s) 2 will cause the switch under test to reload after completion of
the test list.
Switch 1: Running test(s) 2 may disrupt normal system operation
Do you want to continue? [no]: y
Switch#
16:43:29: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 2 Switch 2 has changed to state DOWN
16:43:30: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 9 has changed to state DOWN
16:43:30: %STACKMGR-4-SWITCH_REMOVED: Switch 1 has been REMOVED from the stack
Switch#
16:44:35: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 2 has changed to state UP
16:44:37: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 2 Switch 2 has changed to state UP
16:44:45: %STACKMGR-4-SWITCH_ADDED: Switch 1 has been ADDED to the stack
16:45:00: %STACKMGR-5-SWITCH_READY: Switch 1 is READY
16:45:00: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 1 has changed to state UP
16:45:00: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 2 Switch 1 has changed to state UP
00:00:20: %STACKMGR-4-SWITCH_ADDED: Switch 1 has been ADDED to the stack (Switch-1)
00:00:20: %STACKMGR-4-SWITCH_ADDED: Switch 2 has been ADDED to the stack (Switch-1)
00:00:25: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan (Switch-1)
00:00:29: %SYS-5-CONFIG_I: Configured from memory by console (Switch-1)
00:00:29: %STACKMGR-5-SWITCH_READY: Switch 2 is READY (Switch-1)
00:00:29: %STACKMGR-5-MASTER_READY: Master Switch 2 is READY (Switch-1)
00:00:30: %STACKMGR-5-SWITCH_READY: Switch 1 is READY (Switch-1)
00:00:30: %DIAG-6-TEST_RUNNING: Switch 1: Running TestPortAsicLoopback{ID=2} ...
(Switch-1)
00:00:30: %DIAG-6-TEST_OK: Switch 1: TestPortAsicLoopback{ID=2} has completed successfully
(Switch-1)

This message appears if the configured test can cause the switch to lose stack connectivity:

Switch 3: Running test(s) 2 will cause the switch under test to reload after completion of
the test list.
Switch 3: Running test(s) 2 may disrupt normal system operation
Do you want to continue? [no]:

This message appears if the configured test can cause a stack partition:

Switch 6: Running test(s) 2 will cause the switch under test to reload after completion of
the test list.
Switch 6: Running test(s) 2 will partition stack
Switch 6: Running test(s) 2 may disrupt normal system operation
Do you want to continue? [no]:

Related Commands

Command
Description

show diagnostic

Displays online diagnostic test results.


dot1x

Use the dot1x global configuration command on the switch stack or on a standalone switch to globally enable IEEE 802.1x authentication. Use the no form of this command to return to the default setting.

dot1x {guest-vlan supplicant} | {system-auth-control}

no dot1x {guest-vlan supplicant} | {system-auth-control}


Note Though visible in the command-line help strings, the credentials name keywords are not supported.


Syntax Description

guest-vlan supplicant

Enable optional guest VLAN behavior globally on the switch.

system-auth-control

Enable IEEE 802.1x authentication globally on the switch.


Defaults

IEEE 802.1x authentication is disabled, and the optional guest VLAN behavior is disabled.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You must enable authentication, authorization, and accounting (AAA) and specify the authentication method list before globally enabling IEEE 802.1x authentication. A method list describes the sequence and authentication methods to be used to authenticate a user.

Before globally enabling IEEE 802.1x authentication on a switch, remove the EtherChannel configuration from the interfaces on which IEEE 802.1x authentication and EtherChannel are configured.

If you are using a device running the Cisco Access Control Server (ACS) application for IEEE 802.1x authentication with EAP-Transparent LAN Services (TLS) and with EAP-MD5, make sure that the device is running ACS Version 3.2.1 or later.

You can use the guest-vlan supplicant keywords to enable the optional IEEE 802.1x guest VLAN behavior globally on the switch. For more information, see the dot1x guest-vlan command.

Examples

This example shows how to globally enable IEEE 802.1x authentication on a switch:

Switch(config)# dot1x system-auth-control

This example shows how to globally enable the optional guest VLAN behavior on a switch:

Switch(config)# dot1x guest-vlan supplicant

You can verify your settings by entering the show dot1x [interface interface-id] privileged EXEC command.

Related Commands

Command
Description

dot1x critical (global configuration)

Configures the parameters for the inaccessible authentication bypass feature on the switch.

dot1x guest-vlan

Enables and specifies an active VLAN as an IEEE 802.1x guest VLAN.

dot1x port-control

Enables manual control of the authorization state of the port.

show dot1x [interface interface-id]

Displays IEEE 802.1x status for the specified port.


dot1x auth-fail max-attempts

Use the dot1x auth-fail max-attempts interface configuration command on the switch stack or on a standalone switch to configure the maximum allowable authentication attempts before a port is moved to the restricted VLAN. To return to the default setting, use the no form of this command.

dot1x auth-fail max-attempts max-attempts

no dot1x auth-fail max-attempts

Syntax Description

max-attempts

Specify a maximum number of authentication attempts allowed before a port is moved to the restricted VLAN. The range is 1 to 3, the default value is 3.


Defaults

The default value is 3 attempts.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

If you reconfigure the maximum number of authentication attempts allowed by the VLAN, the change takes effect after the re-authentication timer expires.

Examples

This example shows how to set 2 as the maximum number of authentication attempts allowed before the port is moved to the restricted VLAN on port 3:

Switch# configure terminal 
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface gigabitethernet1/0/3
Switch(config-if)# dot1x auth-fail max-attempts 2
Switch(config-if)# end
Switch(config)# end
Switch#

You can verify your settings by entering the show dot1x [interface interface-id] privileged EXEC command.

Related Commands

Command
Description

dot1x auth-fail vlan [vlan id]

Enables the optional restricted VLAN feature.

dot1x max-reauth-req [count]

Sets the maximum number of times that the switch restarts the authentication process before a port changes to the unauthorized state.

show dot1x [interface interface-id]

Displays IEEE 802.1x status for the specified port.


dot1x auth-fail vlan

Use the dot1x auth-fail vlan interface configuration command on the switch stack or on a standalone switch to enable the restricted VLAN on a port. To return to the default setting, use the no form of this command.

dot1x auth-fail vlan vlan-id

no dot1x auth-fail vlan

Syntax Description

vlan-id

Specify a VLAN in the range of 1 to 4094.


Defaults

No restricted VLAN is configured.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You can configure a restricted VLAN on ports configured as follows:

single-host (default) mode

auto mode for authorization

You should enable re-authentication. The ports in restricted VLANs do not receive re-authentication requests if it is disabled. To start the re-authentication process, the restricted VLAN must receive a link-down event or an Extensible Authentication Protocol (EAP) logoff event from the port. If a host is connected through a hub, the port might never receive a link-down event when that host is disconnected, and, as a result, might not detect any new hosts until the next re-authentication attempt occurs.

If the supplicant fails authentication, the port is moved to a restricted VLAN, and an EAP success message is sent to the supplicant. Because the supplicant is not notified of the actual authentication failure, there might be confusion about this restricted network access. An EAP success message is sent for these reasons:

If the EAP success message is not sent, the supplicant tries to authenticate every 60 seconds (the default) by sending an EAP-start message.

Some hosts (for example, devices running Windows XP) cannot implement DHCP until they receive an EAP success message.

A supplicant might cache an incorrect username and password combination after receiving an EAP success message from the authenticator and re-use that information in every re-authentication. Until the supplicant sends the correct username and password combination, the port remains in the restricted VLAN.

Internal VLANs used for Layer 3 ports cannot be configured as restricted VLANs.

You cannot configure a VLAN to be both a restricted VLAN and a voice VLAN. If you do this, a syslog message is generated.

When a restricted VLAN port is moved to an unauthorized state, the authentication process restarts. If the supplicant fails the authentication process again, the authenticator waits in the held state. After the supplicant has correctly re-authenticated, all IEEE 802.1x ports are reinitialized and treated as normal IEEE 802.1x ports.

When you reconfigure a restricted VLAN as a different VLAN, any ports in the restricted VLAN are also moved, and the ports stay in their currently authorized state.

When you shut down or remove a restricted VLAN from the VLAN database, any ports in the restricted VLAN are immediately moved to an unauthorized state, and the authentication process restarts. The authenticator does not wait in a held state because the restricted VLAN configuration still exists. While the restricted VLAN is inactive, all authentication attempts are counted so that when the restricted VLAN becomes active, the port is immediately placed in the restricted VLAN.

The restricted VLAN is supported only in single host mode (the default port mode). For this reason, when a port is placed in a restricted VLAN, the supplicant's MAC address is added to the MAC address table, and any other MAC address that appears on the port is treated as a security violation.

Examples

This example shows how to configure a restricted VLAN on port 1:

Switch# configure terminal 
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface gigabitethernet1/0/1
Switch(config-if)# dot1x auth-fail vlan 40
Switch(config-if)# end
Switch(config)# end
Switch#

You can verify your configuration by entering the show dot1x [interface interface-id] privileged EXEC command.

Related Commands

Command
Description

dot1x auth-fail max-attempts [max-attempts]

Configures the number of authentication attempts allowed before assigning a supplicant to the restricted VLAN.

show dot1x [interface interface-id]

Displays IEEE 802.1x status for the specified port.


dot1x control-direction

Use the dot1x control-direction interface configuration command to enable the IEEE 802.1x authentication with the wake-on-LAN (WoL) feature and to configure the port control as unidirectional or bidirectional. Use the no form of this command to return to the default setting.

dot1x control-direction {both | in}

no dot1x control-direction

Syntax Description

both

Enable bidirectional control on port. The port cannot receive packets from or send packets to the host.

in

Enable unidirectional control on port. The port can send packets to the host but cannot receive packets from the host.


Defaults

The port is in bidirectional mode.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Use the both keyword or the no form of this command to return to the default setting, bidirectional mode.

For more information about WoL, see the "Using IEEE 802.1x Authentication with Wake-on-LAN" section in the "Configuring IEEE 802.1x Port-Based Authentication" chapter in the software configuration guide.

Examples

This example shows how to enable unidirectional control:

Switch(config-if)# dot1x control-direction in

This example shows how to enable bidirectional control:

Switch(config-if)# dot1x control-direction both

You can verify your settings by entering the show dot1x all privileged EXEC command.

The show dot1x all privileged EXEC command output is the same for all switches except for the port names and the state of the port. If a host is attached to the port but is not yet authenticated, a display similar to this appears:

Supplicant MAC 0002.b39a.9275
AuthSM State = CONNECTING
BendSM State = IDLE
PortStatus = UNAUTHORIZED

If you enter the dot1x control-direction in interface configuration command to enable unidirectional control, this appears in the show dot1x all command output:

ControlDirection  = In

If you enter the dot1x control-direction in interface configuration command and the port cannot support this mode due to a configuration conflict, this appears in the show dot1x all command output:

ControlDirection  = In (Disabled due to port settings)

Related Commands

Command
Description

show dot1x [all | interface interface-id]

Displays control-direction port setting status for the specified interface.


dot1x credentials (global configuration)

Use the dot1x credentials global configuration command to configure a profile on a supplicant switch.

dot1x credentials profile

no dot1x credentials profile

Syntax Description

profile

Specify a profile for the supplicant switch.


Defaults

No profile is configured for the switch.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You must have another switch set up as the authenticator for this switch to be the supplicant.

Examples

This example shows how to configure a switch as a supplicant:

Switch(config)# dot1x credentials profile

You can verify your settings by entering the show running-config privileged EXEC command.

Related Commands

Command
Description

cisp enable

Enables Client Information Signalling Protocol (CISP).

show cisp

Displays CISP information for a specified interface.


dot1x critical (global configuration)

Use the dot1x critical global configuration command on the switch stack or on a standalone switch to configure the parameters for the inaccessible authentication bypass feature, also referred to as critical authentication or the authentication, authorization, and accounting (AAA) fail policy. To return to default settings, use the no form of this command.

dot1x critical {eapol | recovery delay milliseconds}

no dot1x critical {eapol | recovery delay}

Syntax Description

eapol

Specify that the switch sends an EAPOL-Success message when the switch puts the critical port in the critical-authentication state.

recovery delay milliseconds

Set the recovery delay period in milliseconds. The range is from 1 to 10000 milliseconds.


Defaults

The switch does not send an EAPOL-Success message to the host when the switch successfully authenticates the critical port by putting the critical port in the critical-authentication state.

The recovery delay period is 1000 milliseconds (1 second).

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Use the eapol keyword to specify that the switch sends an EAPOL-Success message when the switch puts the critical port in the critical-authentication state.

Use the recovery delay milliseconds keyword to set the recovery delay period during which the switch waits to re-initialize a critical port when a RADIUS server that was unavailable becomes available. The default recovery delay period is 1000 milliseconds. A port can be re-initialized every second.

To enable inaccessible authentication bypass on a port, use the dot1x critical interface configuration command. To configure the access VLAN to which the switch assigns a critical port, use the dot1x critical vlan vlan-id interface configuration command.

Examples

This example shows how to set 200 as the recovery delay period on the switch:

Switch# dot1x critical recovery delay 200

You can verify your configuration by entering the show dot1x privileged EXEC command.

Related Commands

Command
Description

dot1x critical (interface configuration)

Enables the inaccessible authentication bypass feature, and configures the access VLAN for the feature.

show dot1x

Displays IEEE 802.1x status for the specified port.


dot1x critical (interface configuration)

Use the dot1x critical interface configuration command on the switch stack or on a standalone switch to enable the inaccessible-authentication-bypass feature, also referred to as critical authentication or the authentication, authorization, and accounting (AAA) fail policy. You can also configure the access VLAN to which the switch assigns the critical port when the port is in the critical-authentication state. To disable the feature or return to default, use the no form of this command.

dot1x critical [recovery action reinitialize | vlan vlan-id]

no dot1x critical [recovery | vlan]

Syntax Description

recovery action reinitialize

Enable the inaccessible-authentication-bypass recovery feature, and specify that the recovery action is to authenticate the port when an authentication server is available.

vlan vlan-id

Specify the access VLAN to which the switch can assign a critical port. The range is from 1 to 4094.


Defaults

The inaccessible-authentication-bypass feature is disabled.

The recovery action is not configured.

The access VLAN is not configured.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

To specify the access VLAN to which the switch assigns a critical port when the port is in the critical-authentication state, use the vlan vlan-id keywords. The specified type of VLAN must match the type of port, as follows:

If the critical port is an access port, the VLAN must be an access VLAN.

If the critical port is a private VLAN host port, the VLAN must be a secondary private VLAN.

If the critical port is a routed port, you can specify a VLAN, but this is optional.

If the client is running Windows XP and the critical port to which the client is connected is in the critical-authentication state, Windows XP might report that the interface is not authenticated.

If the Windows XP client is configured for DHCP and has an IP address from the DHCP server, receiving an EAP-Success message on a critical port might not re-initiate the DHCP configuration process.

You can configure the inaccessible authentication bypass feature and the restricted VLAN on an IEEE 802.1x port. If the switch tries to re-authenticate a critical port in a restricted VLAN and all the RADIUS servers are unavailable, the switch changes the port state to the critical authentication state, and it remains in the restricted VLAN.

You can configure the inaccessible bypass feature and port security on the same switch port.

Examples

This example shows how to enable the inaccessible authentication bypass feature on port 1:

Switch# configure terminal 
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface gigabitethernet1/0/1
Switch(config-if)# dot1x critical
Switch(config-if)# end
Switch(config)# end
Switch#

You can verify your configuration by entering the show dot1x [interface interface-id] privileged EXEC command.

Related Commands

Command
Description

dot1x critical (global configuration)

Configures the parameters for the inaccessible authentication bypass feature on the switch.

show dot1x [interface interface-id]

Displays IEEE 802.1x status for the specified port.


dot1x default

Use the dot1x default interface configuration command on the switch stack or on a standalone switch to reset the IEEE 802.1x parameters to their default values.

dot1x default

Syntax Description

This command has no arguments or keywords.

Defaults

These are the default values:

The per-port IEEE 802.1x protocol enable state is disabled (force-authorized).

The number of seconds between re-authentication attempts is 3600 seconds.

The periodic re-authentication is disabled.

The quiet period is 60 seconds.

The retransmission time is 30 seconds.

The maximum retransmission number is 2 times.

The host mode is single host.

The client timeout period is 30 seconds.

The authentication server timeout period is 30 seconds.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Examples

This example shows how to reset the IEEE 802.1x parameters on a port:

Switch(config-if)# dot1x default

You can verify your settings by entering the show dot1x [interface interface-id] privileged EXEC command.

Related Commands

Command
Description

show dot1x [interface interface-id]

Displays IEEE 802.1x status for the specified port.


dot1x fallback

Use the dot1xfallback interface configuration command on the switch stack or on a standalone switch to configure a port to use web authentication as a fallback method for clients that do not support IEEE 802.1x authentication. To return to the default setting, use the no form of this command.

dot1x fallback fallback-profile

no dot1x fallback

Syntax Description

fallback-profile

Specify a fallback profile for clients that do not support IEEE 802.1x authentication.


Defaults

No fallback is enabled.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You must enter the dot1x port-control auto interface configuration command on a switch port before entering this command.

Examples

This example shows how to specify a fallback profile to a switch port that has been configured for IEEE 802.1x authentication:

Switch# configure terminal 
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface gigabitethernet1/0/3
Switch(config-if)# dot1x fallback profile1
Switch(config-fallback-profile)# exit
Switch(config)# end

You can verify your settings by entering the show dot1x [interface interface-id] privileged EXEC command.

Related Commands

Command
Description

show dot1x [interface interface-id]

Displays IEEE 802.1x status for the specified port.

fallback profile

Create a web authentication fallback profile.

ip admission

Enable web authentication on a port

ip admission name proxy http

Enable web authentication globally on a switch


dot1x guest-vlan

Use the dot1x guest-vlan interface configuration command on the switch stack or on a standalone switch to specify an active VLAN as an IEEE 802.1x guest VLAN. Use the no form of this command to return to the default setting.

dot1x guest-vlan vlan-id

no dot1x guest-vlan

Syntax Description

vlan-id

Specify an active VLAN as an IEEE 802.1x guest VLAN. The range is 1 to 4094.


Defaults

No guest VLAN is configured.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You can configure a guest VLAN on one of these switch ports:

A static-access port that belongs to a nonprivate VLAN.

A private-VLAN port that belongs to a secondary private VLAN. All the hosts connected to the switch port are assigned to private VLANs, whether or not the posture validation was successful. The switch determines the primary private VLAN by using the primary- and secondary-private-VLAN associations on the switch.

For each IEEE 802.1x port on the switch, you can configure a guest VLAN to provide limited services to clients (a device or workstation connected to the switch) not running IEEE 802.1x authentication. These users might be upgrading their systems for IEEE 802.1x authentication, and some hosts, such as Windows 98 systems, might not be IEEE 802.1x-capable.

When you enable a guest VLAN on an IEEE 802.1x port, the switch assigns clients to a guest VLAN when it does not receive a response to its Extensible Authentication Protocol over LAN (EAPOL) request/identity frame or when EAPOL packets are not sent by the client.

The switch maintains the EAPOL packet history. If another EAPOL packet is detected on the interface during the lifetime of the link, the guest VLAN feature is disabled. If the port is already in the guest VLAN state, the port returns to the unauthorized state, and authentication restarts. The EAPOL history is reset upon loss of link.

To allow clients that failed authentication access to the network, you can use a restricted VLAN by entering the dot1x auth-fail vlan vlan-id interface configuration command.

Any number of non-IEEE 802.1x-capable clients are allowed access when the switch port is moved to the guest VLAN. If an IEEE 802.1x-capable client joins the same port on which the guest VLAN is configured, the port is put into the unauthorized state in the RADIUS-configured or user-configured access VLAN, and authentication is restarted.

Guest VLANs are supported on IEEE 802.1x ports in single-host or multiple-hosts mode.

You can configure any active VLAN except an Remote Switched Port Analyzer (RSPAN) VLAN, a primary private VLAN, or a voice VLAN as an IEEE 802.1x guest VLAN. The guest VLAN feature is not supported on internal VLANs (routed ports) or trunk ports; it is supported only on access ports.

After you configure a guest VLAN for an IEEE 802.1x port to which a DHCP client is connected, you might need to get a host IP address from a DHCP server. You can change the settings for restarting the IEEE 802.1x authentication process on the switch before the DHCP process on the client times out and tries to get a host IP address from the DHCP server. Decrease the settings for the IEEE 802.1x authentication process (dot1x timeout quiet-period and dot1x timeout tx-period interface configuration commands). The amount to decrease the settings depends on the connected IEEE 802.1x client type.

The switch supports MAC authentication bypass. When it is enabled on an IEEE 802.1x port, the switch can authorize clients based on the client MAC address when IEEE 802.1x authentication times out while waiting for an EAPOL message exchange. After detecting a client on an IEEE 802.1x port, the switch waits for an Ethernet packet from the client. The switch sends the authentication server a RADIUS-access/request frame with a username and password based on the MAC address. If authorization succeeds, the switch grants the client access to the network. If authorization fails, the switch assigns the port to the guest VLAN if one is specified. For more information, see the "Using IEEE 802.1x Authentication with MAC Authentication Bypass" section in the "Configuring IEEE 802.1x Port-Based Authentication" chapter of the software configuration guide.

Examples

This example shows how to specify VLAN 5 as an IEEE 802.1x guest VLAN:

Switch(config-if)# dot1x guest-vlan 5

This example shows how to set 3 as the quiet time on the switch, to set 15 as the number of seconds that the switch waits for a response to an EAP-request/identity frame from the client before resending the request, and to enable VLAN 2 as an IEEE 802.1x guest VLAN when an IEEE 802.1x port is connected to a DHCP client:

Switch(config-if)# dot1x timeout quiet-period 3
Switch(config-if)# dot1x timeout tx-period 15
Switch(config-if)# dot1x guest-vlan 2

This example shows how to enable the optional guest VLAN behavior and to specify VLAN 5 as an IEEE 802.1x guest VLAN:

Switch(config)# dot1x guest-vlan supplicant
Switch(config)# interface gigabitethernet2/0/1
Switch(config-if)# dot1x guest-vlan 5

You can verify your settings by entering the show dot1x [interface interface-id] privileged EXEC command.

Related Commands

Command
Description

dot1x

Enables the optional guest VLAN supplicant feature.

show dot1x [interface interface-id]

Displays IEEE 802.1x status for the specified port.


dot1x host-mode

Use the dot1x host-mode interface configuration command on the switch stack or on a standalone switch to allow a single host (client) or multiple hosts on an IEEE 802.1x-authorized port that has the dot1x port-control interface configuration command set to auto. Use the no form of this command to return to the default setting.

dot1x host-mode {multi-host | single-host}

no dot1x host-mode [multi-host | single-host]

Syntax Description

multi-host

Enable multiple-hosts mode on the switch.

single-host

Enable single-host mode on the switch.


Defaults

The default is single-host mode.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Use this command to limit an IEEE 802.1x-enabled port to a single client or to attach multiple clients to an IEEE 802.1x-enabled port. In multiple-hosts mode, only one of the attached hosts needs to be successfully authorized for all hosts to be granted network access. If the port becomes unauthorized (re-authentication fails or an Extensible Authentication Protocol over LAN [EAPOL]-logoff message is received), all attached clients are denied access to the network.

Before entering this command, make sure that the dot1x port-control interface configuration command is set to auto for the specified port.

Examples

This example shows how to enable IEEE 802.1x authentication globally, to enable IEEE 802.1x authentication on a port, and to enable multiple-hosts mode:

Switch(config)# dot1x system-auth-control
Switch(config)# interface gigabitethernet2/0/1
Switch(config-if)# dot1x port-control auto
Switch(config-if)# dot1x host-mode multi-host

You can verify your settings by entering the show dot1x [interface interface-id] privileged EXEC command.

Related Commands

Command
Description

show dot1x [interface interface-id]

Displays IEEE 802.1x status for the specified port.


dot1x initialize

Use the dot1x initialize privileged EXEC command on the switch stack or on a standalone switch to manually return the specified IEEE 802.1x-enabled port to an unauthorized state before initiating a new authentication session on the port.

dot1x initialize [interface interface-id]

Syntax Description

interface interface-id

(Optional) Port to be initialized.


Defaults

There is no default setting.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Use this command to initialize the IEEE 802.1x state machines and to set up a fresh environment for authentication. After you enter this command, the port status becomes unauthorized.

There is not a no form of this command.

Examples

This example shows how to manually initialize a port:

Switch# dot1x initialize interface gigabitethernet2/0/2

You can verify the unauthorized port status by entering the show dot1x [interface interface-id] privileged EXEC command.

Related Commands

Command
Description

show dot1x [interface interface-id]

Displays IEEE 802.1x status for the specified port.


dot1x mac-auth-bypass

Use the dot1x mac-auth-bypass interface configuration command on the switch stack or on a standalone switch to enable the MAC authentication bypass feature. Use the no form of this command to disable MAC authentication bypass feature.

dot1x mac-auth-bypass [eap]

no dot1x mac-auth-bypass

Syntax Description

eap

(Optional) Configure the switch to use Extensible Authentication Protocol (EAP) for authentication.


Defaults

MAC authentication bypass is disabled.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Unless otherwise stated, the MAC authentication bypass usage guidelines are the same as the IEEE 802.1x authentication guidelines.

If you disable MAC authentication bypass from a port after the port has been authenticated with its MAC address, the port state is not affected.

If the port is in the unauthorized state and the client MAC address is not the authentication-server database, the port remains in the unauthorized state. However, if the client MAC address is added to the database, the switch can use MAC authentication bypass to re-authorize the port.

If the port is in the authorized state, the port remains in this state until re-authorization occurs.

If an EAPOL packet is detected on the interface during the lifetime of the link, the switch determines that the device connected to that interface is an IEEE 802.1x-capable supplicant and uses IEEE 802.1x authentication (not MAC authentication bypass) to authorize the interface.

Clients that were authorized with MAC authentication bypass can be re-authenticated.

For more information about how MAC authentication bypass and IEEE 802.lx authentication interact, see the "Understanding IEEE 802.1x Authentication with MAC Authentication Bypass" section and the "IEEE 802.1x Authentication Configuration Guidelines" section in the "Configuring IEEE 802.1x Port-Based Authentication" chapter of the software configuration guide.

Examples

This example shows how to enable MAC authentication bypass and to configure the switch to use EAP for authentication:

Switch(config-if)# dot1x mac-auth-bypass eap

You can verify your settings by entering the show dot1x [interface interface-id] privileged EXEC command.

Related Commands

Command
Description

show dot1x [interface interface-id]

Displays IEEE 802.1x status for the specified port.


dot1x max-reauth-req

Use the dot1x max-reauth-req interface configuration command on the switch stack or on a standalone switch to set the maximum number of times that the switch restarts the authentication process before a port changes to the unauthorized state. Use the no form of this command to return to the default setting.

dot1x max-reauth-req count

no dot1x max-reauth-req

Syntax Description

count

Sets the number of times that switch retransmits EAPOL-Identity-Request frames to start the authentication process before the port changes to the unauthorized state. If a non-802.1x capable device is connected to a port, the switch retries two authentication attempts by default. If a guest VLAN is configured on the port, after two re-authentication attempts, the port is authorized on the guest vlan by default. The range is 1 to 10. The default is 2.


Defaults

The default is 2 times.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You should change the default value of this command only to adjust for unusual circumstances such as unreliable links or specific behavioral problems with certain clients and authentication servers.

Examples

This example shows how to set 4 as the number of times that the switch restarts the authentication process before the port changes to the unauthorized state:

Switch(config-if)# dot1x max-reauth-req 4

You can verify your settings by entering the show dot1x [interface interface-id] privileged EXEC command.

Related Commands

Command
Description

dot1x max-req

Sets the maximum number of times that the switch forwards an EAP frame (assuming that no response is received) to the authentication server before restarting the authentication process.

dot1x timeout tx-period

Sets the number of seconds that the switch waits for a response to an EAP-request/identity frame from the client before resending the request.

show dot1x [interface interface-id]

Displays IEEE 802.1x status for the specified port.


dot1x max-req

Use the dot1x max-req interface configuration command on the switch stack or on a standalone switch to set the maximum number of times that the switch sends an Extensible Authentication Protocol (EAP) frame from the authentication server (assuming that no response is received) to the client before restarting the authentication process. Use the no form of this command to return to the default setting.

dot1x max-req count

no dot1x max-req

Syntax Description

count

Number of times that the switch attempts to retransmit EAPOL DATA packets before restarting the authentication process. For example, if a problem occurs on a supplicant during the authentication process, the authenticator will re-transmit data requests two times before stopping the process. The range is 1 to 10; the default is 2.


Defaults

The default is 2 times.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You should change the default value of this command only to adjust for unusual circumstances such as unreliable links or specific behavioral problems with certain clients and authentication servers.

Examples

This example shows how to set 5 as the number of times that the switch sends an EAP frame from the authentication server to the client before restarting the authentication process:

Switch(config-if)# dot1x max-req 5

You can verify your settings by entering the show dot1x [interface interface-id] privileged EXEC command.

Related Commands

Command
Description

dot1x timeout tx-period

Sets the number of seconds that the switch waits for a response to an EAP-request/identity frame from the client before resending the request.

show dot1x [interface interface-id]

Displays IEEE 802.1x status for the specified port.


dot1x pae

Use the dot1x pae interface configuration command on the switch stack or on a standalone switch to configure the port as an IEEE 802.1x port access entity (PAE) authenticator. Use the no form of this command to disable IEEE 802.1x authentication on the port.

dot1x pae authenticator

no dot1x pae

Syntax Description

This command has no arguments or keywords.

Defaults

The port is not an IEEE 802.1x PAE authenticator, and IEEE 802.1x authentication is disabled on the port.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Use the no dot1x pae interface configuration command to disable IEEE 802.1x authentication on the port.

When you configure IEEE 802.1x authentication on a port, such as by entering the dot1x port-control interface configuration command, the switch automatically configures the port as an EEE 802.1x authenticator. After the no dot1x pae interface configuration command is entered, the Authenticator PAE operation is disabled.

Examples

This example shows how to disable IEEE 802.1x authentication on the port:

Switch(config-if)# no dot1x pae

You can verify your settings by entering the show dot1x or show eap privileged EXEC command.

Related Commands

Command
Description

show dot1x

Displays IEEE 802.1x statistics, administrative status, and operational status for the switch or for the specified port.

show eap

Displays EAP registration and session information for the switch or for the specified port.


dot1x port-control

Use the dot1x port-control interface configuration command on the switch stack or on a standalone switch to enable manual control of the authorization state of the port. Use the no form of this command to return to the default setting.

dot1x port-control {auto | force-authorized | force-unauthorized}

no dot1x port-control

Syntax Description

auto

Enable authentication on the port and cause the port to change to the authorized or unauthorized state based on the IEEE 802.1x authentication exchange between the switch and the client.

force-authorized

Disable authentication on the port and cause the port to transition to the authorized state without an authentication exchange. The port sends and receives normal traffic without authentication of the client.

force-unauthorized

Deny all access through this port by forcing the port to change to the unauthorized state, ignoring all attempts by the client to authenticate. The switch cannot provide authentication services to the client through the port.


Defaults

The default is force-authorized.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You must globally enable IEEE 802.1x authentication on the switch by using the dot1x system-auth-control global configuration command before enabling IEEE 802.1x authentication on a specific port.

The IEEE 802.1x standard is supported on Layer 2 static-access ports, voice VLAN ports, and Layer 3 routed ports.

You can use the auto keyword only if the port is not configured as one of these:

Trunk port—If you try to enable IEEE 802.1x authentication on a trunk port, an error message appears, and IEEE 802.1x is not enabled. If you try to change the mode of an IEEE 802.1x-enabled port to trunk, an error message appears, and the port mode is not changed.

Dynamic ports—A port in dynamic mode can negotiate with its neighbor to become a trunk port. If you try to enable IEEE 802.1x authentication on a dynamic port, an error message appears, and IEEE 802.1x authentication is not enabled. If you try to change the mode of an IEEE 802.1x-enabled port to dynamic, an error message appears, and the port mode is not changed.

Dynamic-access ports—If you try to enable IEEE 802.1x authentication on a dynamic-access (VLAN Query Protocol [VQP]) port, an error message appears, and IEEE 802.1x authentication is not enabled. If you try to change an IEEE 802.1x-enabled port to dynamic VLAN assignment, an error message appears, and the VLAN configuration is not changed.

EtherChannel port—Do not configure a port that is an active or a not-yet-active member of an EtherChannel as an IEEE 802.1x port. If you try to enable IEEE 802.1x authentication on an EtherChannel port, an error message appears, and IEEE 802.1x authentication is not enabled.

Switched Port Analyzer (SPAN) and Remote SPAN (RSPAN) destination ports—You can enable IEEE 802.1x authentication on a port that is a SPAN or RSPAN destination port. However, IEEE 802.1x authentication is disabled until the port is removed as a SPAN or RSPAN destination. You can enable IEEE 802.1x authentication on a SPAN or RSPAN source port.

To globally disable IEEE 802.1x authentication on the switch, use the no dot1x system-auth-control global configuration command. To disable IEEE 802.1x authentication on a specific port or to return to the default setting, use the no dot1x port-control interface configuration command.

Examples

This example shows how to enable IEEE 802.1x authentication on a port:

Switch(config)# interface gigabitethernet2/0/1
Switch(config-if)# dot1x port-control auto

You can verify your settings by entering the show dot1x [interface interface-id] privileged EXEC command.

Related Commands

Command
Description

show dot1x [interface interface-id]

Displays IEEE 802.1x status for the specified port.


dot1x re-authenticate

Use the dot1x re-authenticate privileged EXEC command on the switch stack or on a standalone switch to manually initiate a re-authentication of the specified IEEE 802.1x-enabled port.

dot1x re-authenticate [interface interface-id]

Syntax Description

interface interface-id

(Optional) Stack switch number, module, and port number of the interface to re-authenticate.


Defaults

There is no default setting.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You can use this command to re-authenticate a client without waiting for the configured number of seconds between re-authentication attempts (re-authperiod) and automatic re-authentication.

Examples

This example shows how to manually re-authenticate the device connected to a port:

Switch# dot1x re-authenticate interface gigabitethernet2/0/1

Related Commands

Command
Description

dot1x reauthentication

Enables periodic re-authentication of the client.

dot1x timeout reauth-period

Sets the number of seconds between re-authentication attempts.


dot1x reauthentication

Use the dot1x reauthentication interface configuration command on the switch stack or on a standalone switch to enable periodic re-authentication of the client. Use the no form of this command to return to the default setting.

dot1x reauthentication

no dot1x reauthentication

Syntax Description

This command has no arguments or keywords.

Defaults

Periodic re-authentication is disabled.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You configure the amount of time between periodic re-authentication attempts by using the dot1x timeout reauth-period interface configuration command.

Examples

This example shows how to disable periodic re-authentication of the client:

Switch(config-if)# no dot1x reauthentication

This example shows how to enable periodic re-authentication and to set the number of seconds between re-authentication attempts to 4000 seconds:

Switch(config-if)# dot1x reauthentication
Switch(config-if)# dot1x timeout reauth-period 4000

You can verify your settings by entering the show dot1x [interface interface-id] privileged EXEC command.

Related Commands

Command
Description

dot1x re-authenticate

Manually initiates a re-authentication of all IEEE 802.1x-enabled ports.

dot1x timeout reauth-period

Sets the number of seconds between re-authentication attempts.

show dot1x [interface interface-id]

Displays IEEE 802.1x status for the specified port.


dot1x supplicant force-multicast

Use the dot1x supplicant force-multicast global configuration command to force a supplicant switch to send only multicast Extensible Authentication Protocol over LAN (EAPOL) packets whenever it receives multicast or unicast EAPOL packets. Use the no form of this command to return to the default setting.

dot1x supplicant force-multicast

no dot1x supplicant force-multicast

Syntax Description

This command has no arguments or keywords.

Defaults

The supplicant switch sends unicast EAPoL packets when it receives unicast EAPOL packets. Similarly, it sends multicast EAPOL packets when it receives multicast EAPOL packets.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Enable this command on the supplicant switch for Network Edge Access Topology (NEAT) to work in all host modes.

Examples

This example shows how force a supplicant switch to send multicast EAPOL packets to authenticator switch:

Switch(config)# dot1x supplicant force-multicast

Related Commands

Command
Description

cisp enable

Enable Client Information Signalling Protocol (CISP) on a switch so that it acts as an authenticator to a supplicant switch.

dot1x credentials

Configure the 802.1x supplicant credentials on the port.

dot1x pae supplicant

Configure an interface to act only as a supplicant.


dot1x test eapol-capable

Use the dot1x test eapol-capable privileged EXEC command on the switch stack or on a standalone switch to monitor IEEE 802.1x activity on all the switch ports and to display information about the devices that are connected to the ports that support IEEE 802.1x.

dot1x test eapol-capable [interface interface-id]

Syntax Description

interface interface-id

(Optional) Port to be queried.


Defaults

There is no default setting.

Command Modes

Privileged EXEC

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Use this command to test the IEEE 802.1x capability of the devices connected to all ports or to specific ports on a switch.

There is not a no form of this command.

Examples

This example shows how to enable the IEEE 802.1x readiness check on a switch to query a port. It also shows the response received from the queried port verifying that the device connected to it is IEEE 802.1x-capable:

switch# dot1x test eapol-capable interface gigabitethernet1/0/13

DOT1X_PORT_EAPOL_CAPABLE:DOT1X: MAC 00-01-02-4b-f1-a3 on gigabitethernet1/0/13 is EAPOL 
capable

Related Commands

Command
Description

dot1x test timeout timeout

Configures the timeout used to wait for EAPOL response to an IEEE 802.1x readiness query.


dot1x test timeout

Use the dot1x test timeout global configuration command on the switch stack or on a standalone switch to configure the timeout used to wait for EAPOL response from a port being queried for IEEE 802.1x readiness.

dot1x test timeout timeout

Syntax Description

timeout

Time in seconds to wait for an EAPOL response. The range is from 1 to 65535 seconds.


Defaults

The default setting is 10 seconds.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

Use this command to configure the timeout used to wait for EAPOL response.

There is not a no form of this command.

Examples

This example shows how to configure the switch to wait 27 seconds for an EAPOL response:

Switch# dot1x test timeout 27

You can verify the timeout configuration status by entering the show run privileged EXEC command.

Related Commands

Command
Description

dot1x test eapol-capable [interface interface-id]

Checks for IEEE 802.1x readiness on devices connected to all or to specified IEEE 802.1x-capable ports.


dot1x timeout

Use the dot1x timeout interface configuration command on the switch stack or on a standalone switch to set IEEE 802.1x timers. Use the no form of this command to return to the default setting.

dot1x timeout {quiet-period seconds | ratelimit-period seconds | reauth-period {seconds | server} | server-timeout seconds | supp-timeout seconds | tx-period seconds}

no dot1x timeout {quiet-period | reauth-period | server-timeout | supp-timeout | tx-period}

Syntax Description

quiet-period seconds

Number of seconds that the switch remains in the quiet state following a failed authentication exchange with the client. The range is 1 to 65535.

ratelimit-period seconds

Number of seconds that the switch ignores Extensible Authentication Protocol over LAN (EAPOL) packets from clients that have been successfully authenticated during this duration. The range is 1 to 65535.

reauth-period {seconds | server}

Set the number of seconds between re-authentication attempts.

The keywords have these meanings:

seconds—Sets the number of seconds from 1 to 65535; the default is 3600 seconds.

server—Sets the number of seconds as the value of the Session-Timeout RADIUS attribute (Attribute[27]).

server-timeout seconds

Number of seconds that the switch waits for the retransmission of packets by the switch to the authentication server.

The range is 1 to 65535. However, we recommend a minimum setting of 30.

supp-timeout seconds

Number of seconds that the switch waits for the retransmission of packets by the switch to the IEEE 802.1x client. The range is 30 to 65535.

tx-period seconds

Number of seconds that the switch waits for a response to an EAP-request/identity frame from the client before retransmitting the request. The range is 1 to 65535.


Defaults

These are the default settings:

reauth-period is 3600 seconds.

quiet-period is 60 seconds.

tx-period is 5 seconds.

supp-timeout is 30 seconds.

server-timeout is 30 seconds.

rate-limit is 1 second.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

You should change the default value of this command only to adjust for unusual circumstances such as unreliable links or specific behavioral problems with certain clients and authentication servers.

The dot1x timeout reauth-period interface configuration command affects the behavior of the switch only if you have enabled periodic re-authentication by using the dot1x reauthentication interface configuration command.

During the quiet period, the switch does not accept or initiate any authentication requests. If you want to provide a faster response time to the user, enter a number smaller than the default.

When the ratelimit-period is set to 0 (the default), the switch does not ignore EAPOL packets from clients that have been successfully authenticated and forwards them to the RADIUS server.

Examples

This example shows how to enable periodic re-authentication and to set 4000 as the number of seconds between re-authentication attempts:

Switch(config-if)# dot1x reauthentication
Switch(config-if)# dot1x timeout reauth-period 4000

This example shows how to enable periodic re-authentication and to specify the value of the Session-Timeout RADIUS attribute as the number of seconds between re-authentication attempts:

Switch(config-if)# dot1x reauthentication
Switch(config-if)# dot1x timeout reauth-period server

This example shows how to set 30 seconds as the quiet time on the switch:

Switch(config-if)# dot1x timeout quiet-period 30

This example shows how to set 45 seconds as the switch-to-authentication server retransmission time:

Switch(config)# dot1x timeout server-timeout 45

This example shows how to set 45 seconds as the switch-to-client retransmission time for the EAP request frame:

Switch(config-if)# dot1x timeout supp-timeout 45

This example shows how to set 60 as the number of seconds to wait for a response to an EAP-request/identity frame from the client before re-transmitting the request:

Switch(config-if)# dot1x timeout tx-period 60

This example shows how to set 30 as the number of seconds that the switch ignores EAPOL packets from successfully authenticated clients:

Switch(config-if)# dot1x timeout ratelimit-period 30

You can verify your settings by entering the show dot1x privileged EXEC command.

Related Commands

Command
Description

dot1x max-req

Sets the maximum number of times that the switch sends an EAP-request/identity frame before restarting the authentication process.

dot1x reauthentication

Enables periodic re-authentication of the client.

show dot1x

Displays IEEE 802.1x status for all ports.


dot1x violation-mode

Use the dot1x violation-mode interface configuration command on the switch stack or on a standalone switch to configure the violation modes that occur when a new device connects to a port or when a new device connects to a port after the maximum number of devices are connected to that port.

dot1x violation-mode {shutdown | restrict | protect}

no dot1x violation-mode

Syntax Description

shutdown

Error disables the port or the virtual port on which a new unexpected MAC address occurs.

restrict

Generates a syslog error when a violation error occurs.

protect

Silently discards packets from any new MAC addresses. This is the default setting.


Defaults

By default dot1x violation-mode protect is enabled.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Examples

This example shows how to configure an IEEE 802.1x-enabled port as error disabled and to shut down when a new device connects to the port:

Switch(config-if)# dot1x violation-mode shutdown

This example shows how to configure an IEEE 802.1x-enabled port to generate a system error message and change the port to restricted mode when a new device connects to the port:

Switch(config-if)# dot1x violation-mode restrict

This example shows how to configure an IEEE 802.1x-enabled port to ignore a new connected device when it is connected to the port:

Switch(config-if)# dot1x violation-mode protect

You can verify your settings by entering the show dot1x [interface interface-id] privileged EXEC command.

Related Commands

Command
Description

show dot1x [interface interface-id]

Displays IEEE 802.1x status for the specified port.


duplex

Use the duplex interface configuration command on the switch stack or on a standalone switch to specify the duplex mode of operation for a port. Use the no form of this command to return the port to its default value.

duplex {auto | full | half}

no duplex

Syntax Description

auto

Enable automatic duplex configuration; port automatically detects whether it should run in full- or half-duplex mode, depending on the attached device mode.

full

Enable full-duplex mode.

half

Enable half-duplex mode (only for interfaces operating at 10 or 100 Mb/s). You cannot configure half-duplex mode for interfaces operating at 1000 or 10,000 Mb/s.


Defaults

The default is auto for Gigabit Ethernet ports.

You cannot configure the duplex mode on 10-Gigabit Ethernet ports; it is always full.

The default is full for the 100BASE- LX small form-factor pluggable (SFP) modules.

The default is half for the 100BASE-FX SFP modules.

Duplex options are not supported on the 1000BASE-x (where -x is -BX, -CWDM, -LX, -SX, or -ZX) SFP modules.

For information about which SFP modules are supported on your switch, see the product release notes.

Command Modes

Interface configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

For Fast Ethernet ports on stack members other than Catalyst 3750-X switches, setting the port to auto has the same effect as specifying half if the attached device does not autonegotiate the duplex parameter.

For Gigabit Ethernet ports, setting the port to auto has the same effect as specifying full if the attached device does not autonegotiate the duplex parameter.


Note Half-duplex mode is supported on Gigabit Ethernet interfaces if the duplex mode is auto and the connected device is operating at half duplex. However, you cannot configure these interfaces to operate in half-duplex mode.


Certain ports can be configured to be either full duplex or half duplex. Applicability of this command depends on the device to which the switch is attached.

If both ends of the line support autonegotiation, we highly recommend using the default autonegotiation settings. If one interface supports autonegotiation and the other end does not, configure duplex and speed on both interfaces; do use the auto setting on the supported side.

If the speed is set to auto, the switch negotiates with the device at the other end of the link for the speed setting and then forces the speed setting to the negotiated value. The duplex setting remains as configured on each end of the link, which could result in a duplex setting mismatch.

You can configure the duplex setting when the speed is set to auto.


Caution Changing the interface speed and duplex mode configuration might shut down and re-enable the interface during the reconfiguration.

For guidelines on setting the switch speed and duplex parameters, see the "Configuring Interface Characteristics" chapter in the software configuration guide for this release.

Examples

This example shows how to configure an interface for full-duplex operation:

Switch(config)# interface gigabitethernet1/0/1 
Switch(config-if)# duplex full

You can verify your setting by entering the show interfaces privileged EXEC command.

Related Commands

Command
Description

show interfaces

Displays the interface settings on the switch.

speed

Sets the speed on a 10/100 or 10/100/1000 Mb/s interface.


errdisable detect cause

Use the errdisable detect cause global configuration command on the switch stack or on a standalone switch to enable error-disabled detection for a specific cause or all causes. Use the no form of this command to disable the error-disabled detection feature.

errdisable detect cause {all | arp-inspection | bpduguard | dhcp-rate-limit | dtp-flap | gbic-invalid | inline-power | l2ptguard |link-flap | loopback | pagp-flap | security-violation shutdown vlan | sfp-config-mismatch}

no errdisable detect cause {all | arp-inspection | bpduguard | dhcp-rate-limit | dtp-flap | gbic-invalid | inline-power | l2ptguard |link-flap | loopback | pagp-flap | security-violation shutdown vlan | sfp-config-mismatch}

For the BPDU guard and port-security features, you can use this command to globally configure the switch to shut down just the offending VLAN on the port when a violation occurs, instead of shutting down the entire port.

When the per-VLAN error-disable feature is turned off and a BPDU guard violation occurs, the entire port is disabled. Use the no form of this command to disable the per-VLAN error-disable feature.

errdisable detect cause bpduguard shutdown vlan

no errdisable detect cause bpduguard shutdown vlan

Syntax Description

all

Enable error detection for all error-disabled causes.

arp-inspection

Enable error detection for dynamic Address Resolution Protocol (ARP) inspection.

bpduguard shutdown vlan

Enable per-VLAN error-disable for BPDU guard.

dhcp-rate-limit

Enable error detection for DHCP snooping.

dtp-flap

Enable error detection for the Dynamic Trunking Protocol (DTP) flapping.

gbic-invalid

Enable error detection for an invalid Gigabit Interface Converter (GBIC) module.

Note This error refers to an invalid small form-factor pluggable (SFP) module.

inline-power

Enable error detection for the Power over Ethernet (PoE) error-disabled cause.

This keyword is supported only on switches with PoE ports.

l2ptguard

Enable error detection for a Layer 2 protocol-tunnel error-disabled cause.

link-flap

Enable error detection for link-state flapping.

loopback

Enable error detection for detected loopbacks.

pagp-flap

Enable error detection for the Port Aggregation Protocol (PAgP) flap error-disabled cause.

security-violation shutdown vlan

Enable voice aware 802.1x security.

sfp-config-mismatch

Enable error detection on an SFP configuration mismatch.


Command Default

Detection is enabled for all causes. All causes, except for per-VLAN error disabling, are configured to shut down the entire port.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

A cause (link-flap, dhcp-rate-limit, and so forth) is the reason for the error-disabled state. When a cause is detected on an interface, the interface is placed in an error-disabled state, an operational state that is similar to a link-down state.

When a port is error-disabled, it is effectively shut down, and no traffic is sent or received on the port. For the BPDU guard, voice aware 802.1x security, and port-security features, you can configure the switch to shut down just the offending VLAN on the port when a violation occurs, instead of shutting down the entire port.

If you set a recovery mechanism for the cause by entering the errdisable recovery global configuration command for the cause, the interface is brought out of the error-disabled state and allowed to retry the operation when all causes have timed out. If you do not set a recovery mechanism, you must enter the shutdown and then the no shutdown commands to manually recover an interface from the error-disabled state.

Examples

This example shows how to enable error-disabled detection for the link-flap error-disabled cause:

Switch(config)# errdisable detect cause link-flap

This command shows how to globally configure BPDU guard for per-VLAN error disable:

Switch(config)# errdisable detect cause bpduguard shutdown vlan

This command shows how to globally configure voice aware 802.1x security for per-VLAN error disable:

Switch(config)# errdisable detect cause security-violation shutdown vlan 

You can verify your setting by entering the show errdisable detect privileged EXEC command.

Related Commands

Command
Description

show errdisable detect

Displays error-disabled detection information.

show interfaces status err-disabled

Displays interface status or a list of interfaces in the error-disabled state.

clear errdisable interface

Clears the error-disabled state from a port or VLAN that was error disabled by the per-VLAN error disable feature.


errdisable detect cause small-frame

Use the errdisable detect cause small-frame global configuration command on the switch stack or on a standalone switch to allow any switch port to be error disabled if incoming VLAN-tagged packets are small frames (67 bytes or less) and arrive at the minimum configured rate (the threshold). Use the no form of this command to return to the default setting.

errdisable detect cause small-frame

no errdisable detect cause small-frame

Syntax Description

This command has no arguments or keywords.

Defaults

This feature is disabled.

Command Modes

Global configuration

Command History

Release
Modification

12.2(53)SE2

This command was introduced.


Usage Guidelines

This command globally enables the small-frame arrival feature. Use the small violation-rate interface configuration command to set the threshold for each port.

You can configure the port to be automatically re-enabled by using the errdisable recovery cause small-frame global configuration command. You configure the recovery time by using the errdisable recovery interval interval global configuration command.

Examples

This example shows how to enable the switch ports to be put into the error-disabled mode if incoming small frames arrive at the configured threshold:

Switch(config)# errdisable detect cause small-frame

You can verify your setting by entering the show interfaces privileged EXEC command.

Related Commands

Command
Description

errdisable recovery cause small-frame

Enables the recovery timer.

errdisable recovery interval interval

Specifies the time to recover from the specified error-disabled state.

show interfaces

Displays the interface settings on the switch, including input and output flow control.

small-frame violation rate

Configures the rate (threshold) for incoming small frames to cause a port to be put into the error-disabled state.


errdisable recovery

Use the errdisable recovery global configuration command on the switch stack or on a standalone switch to configure the recover mechanism variables. Use the no form of this command to return to the default setting.

errdisable recovery {cause {all | arp-inspection | bpduguard | channel-misconfig | dhcp-rate-limit | dtp-flap | gbic-invalid | inline-power | l2ptguard | link-flap | loopback | pagp-flap | psecure-violation | security-violation | sfp-mismatch | udld | vmps}} | {interval interval}

no errdisable recovery {cause {all | arp-inspection | bpduguard | channel-misconfig | dhcp-rate-limit | dtp-flap | gbic-invalid | inline-power | l2ptguard | link-flap | loopback | pagp-flap | psecure-violation | security-violation | sfp-mismatch | udld | vmps}}| {interval interval}

Syntax Description

cause

Enable the error-disabled mechanism to recover from a specific cause.

all

Enable the timer to recover from all error-disabled causes.

bpduguard

Enable the timer to recover from the bridge protocol data unit (BPDU) guard error-disabled state.

arp-inspection

Enable the timer to recover from the Address Resolution Protocol (ARP) inspection error-disabled state.

channel-misconfig

Enable the timer to recover from the EtherChannel misconfiguration error-disabled state.

dhcp-rate-limit

Enable the timer to recover from the DHCP snooping error-disabled state.

dtp-flap

Enable the timer to recover from the Dynamic Trunking Protocol (DTP) flap error-disabled state.

gbic-invalid

Enable the timer to recover from an invalid Gigabit Interface Converter (GBIC) module error-disabled state.

Note This error refers to an invalid small form-factor pluggable (SFP) error-disabled state.

inline-power

Enable the timer to recover from the Power over Ethernet (PoE) error-disabled state.

This keyword is supported only on switches with PoE ports.

l2ptguard

Enable the timer to recover from a Layer 2 protocol tunnel error-disabled state.

link-flap