Guest

Support

Index

Hierarchical Navigation

  • Viewing Options

  • PDF (200.2 KB)
  • Feedback
Index

Table Of Contents

Numerics - A - B - C - D - E - F - G - H - I - J - L - M - N - O - P - R - S - T - W - X -

Index

Numerics

10/100/1000 ports

cable lengths 1-4, 2-27

connecting to 2-27

described 1-4

pinouts B-1

recommended cables 2-27

10/100 Ethernet management port 1-23

10-Gigabit Ethernet module slots

connecting devices 2-23

19- and 24-inch racks 2-18

A

AC power

power-supply module described 1-19

specifications A-3

adapter pinouts, terminal

RJ-45-to-DB-25 B-9

RJ-45-to-DB-9 B-8

airflow patterns 1-21

altitude, operating and storage A-1

autonegotiation

default setting 2-27

troubleshooting 4-4

B

bodily injury protection warning 2-15

brackets

See mounting brackets

C

cable guide, attaching 2-18

cable lengths B-5

cables

crossover

four twisted-pair pinout B-7

identifying B-8

two twisted-pair pinout B-7

patch cable B-2

recommended 2-27

StackWise

cable numbers 1-19

connecting to 2-20, 2-21, 2-22

straight-through

four twisted-pair pinout B-7

two twisted-pair pinout B-7

Cisco IOS command-line interface 1-24

Cisco IP Phones, connecting to2-27to 2-28

Cisco Network Assistant 1-24

Cisco Power Calculator 2-27

CiscoView 1-24

CLI 1-24

accessing by using Express Setup C-1

accessing through console port C-1

code compliance warning 2-3

command-line interface

See CLI

connection procedures2-22to 2-28

connectors and cablesB-1to B-9

console port

connectors and cables B-4

described 1-23

crossover cable

See cables

D

DC power

power-supply module described 1-19

specifications A-3

DC power warning 3-8

device manager

described 1-24

to configure switch 2-29

diagnosing problems 4-1

dimensions A-2

duplex

default setting 2-27

LED 1-11

troubleshooting 4-4

E

electrical noise, avoiding 2-4

electromagnetic safety 2-3

Ethernet and fiber cable troubleshooting 4-2

Ethernet management port

described 1-23

LED POST results 4-1

expandable power supply

See XPS

Express Setup

accessing CLI by using C-1

for initial switch configuration 2-19

using to clear switch IP address 4-5

F

fan module

airflow patterns 1-21

described 1-21

installing 3-15

front panel

10/100/1000 Ethernet ports 1-4

clearance 2-3

described1-3to 1-17

LEDs1-9to 1-16

network modules 1-6

PoE+ ports 1-5

G

ground connection 3-9

ground connection warning 3-9

H

HP OpenView 1-24

humidity, relative A-1

I

installation

assigning the IP address 2-1, C-6

network modules 2-23

rack-mounting2-15to 2-18

SFP and SFP+ modules2-24to 2-26

site requirements 2-3

starting the terminal emulation software C-3

table or shelf-mounting 2-19

See also procedures

J

jewelry removal warning 2-2

L

LEDs

color meanings 1-11

duplex 1-11

front panel1-9to 1-16

interpreting 1-11

master 1-14

PoE+ 1-11

port1-11to 1-14

port mode1-11to 1-13

POST results 4-1

speed 1-11

stack 1-14

StackPower 1-14

STATUS 1-11

system 1-10

troubleshooting with 4-1

XPS??to 1-11

lightning activity warning 2-2

Link

faults caution 1-16

link status troubleshooting 4-2

local and national electrical codes compliance 2-3

M

mode button 1-9

mounting, table or shelf 2-19

mounting brackets

rack-mount 2-18

table- or shelf-mounting 2-19

N

NEBS standard for electromagnetic safety 2-3

Network Assistant 2-29

Network Equipment Building Systems

See NEBS

network modules

described 1-6

installation 2-23

noise, electrical 2-4

O

outside connections warning 2-3

overheating warning 2-2

P

pinouts

10/100/1000 ports B-1

adaptersB-8to B-9

console port B-9

crossover cable B-8

crossover cables

four twisted-pair B-7

two twisted-pair B-7

RJ-45-to-DB-25 terminal adapter B-9

RJ-45-to-DB-9 terminal adapter B-8

SFP and SFP+ module ports B-2

straight-through cables

four twisted-pair B-7

two twisted-pair B-7

PoE+

faults caution 1-13

LED 1-11, 1-15

port connections 2-27

ports described 1-5

PoE+ (continued)

power planning tool 2-27

shock hazard warning 2-28

troubleshooting 4-3

port and interface troubleshooting 4-4

port LEDs1-11to 1-14

port modes

changing 1-9

LEDs 1-11

See also mode button

ports

10/100/1000

connecting to 2-27

described 1-4

pinouts B-1

recommended cables 2-27

POST

LEDs 4-1

running at power on 4-1

power connection warning 2-2

Power over Ethernet

See PoE+

power specifications A-3

power-supply modules

described 1-19

installation 3-7

procedures

connection2-22to 2-28

installation2-14to 2-19

product disposal warning 2-3

R

rack-mounting2-15to 2-18

rear panel

clearance 2-3

console port 1-23

described1-17to 1-18

Ethernet management port 1-23

fan module 1-21

power-supply module 1-19

StackWise ports 1-19

XPS connector 1-21

restricted access area warning 2-2

RJ-45 connector, console port B-5

RJ-45 console port 1-17, 1-18

LED 1-23

S

safety 2-1

serial number location 4-6

servicing equipment warning 2-2

SFP+ modules

supported 1-9

SFP and SFP+ modules

bale-clasp latch removal 2-26

connectors B-2

described 1-7

installation2-24to 2-26

patch cable B-2

SFP modules

supported 1-7

shelf-mounting 2-19

shielding Ethernet cables warning 2-2

Simple Network Management Protocol

See SNMP

SNMP network management platforms 1-24

software switch management 1-24

specifications A-1

speed

default setting 2-27

troubleshooting 4-4

stacking equipment warning 2-2

stacking powering considerations 2-8

StackWise ports 1-19

straight-through cable pinout

four twisted-pair B-7

two twisted-pair B-7

SunNet Manager 1-24

switch models 1-1

system LED 1-10

T

table-mounting 2-19

technical specifications A-1

telco racks 2-18

Telnet, and accessing the CLI 1-24

temperature, operating A-1

transceiver troubleshooting 4-3

troubleshooting

bad or damaged cable 4-2

connection problems 4-2

diagnosing problems 4-1

Ethernet and fiber cables 4-2

link status 4-2

ping end device 4-4

PoE+ connections 4-3

port and interface settings 4-4

POST 4-1

serial number location 4-6

spanning tree loops 4-4

speed, duplex, and autonegotiation 4-4

transceivers 4-3

with LEDs 4-1

troubleshooting spanning tree loops 4-4

W

warnings

code compliance 2-3

connecting outside of building 2-3

connecting the power 2-2

DC power 3-8

disposal of product 2-3

ground connection 3-9

installation 2-1

lightning activity 2-2

overheating 2-2

PoE+ shock hazard 2-28

preventing bodily injury 2-15

removing jewelry 2-2

restricted access area 2-2

servicing equipment 2-2

shielding Ethernet cables 2-2

stacking equipment 2-2

weight A-1

X

XPS

connector 1-21

described 1-21

LED1-11, ??to 1-11