Catalyst 3550 Multilayer Switch Software Configuration Guide, 12.1(4)EA1
Unsupported CLI Commands
Downloads: This chapterpdf (PDF - 133.0KB) The complete bookPDF (PDF - 12.48MB) | Feedback

Unsupported CLI Commands in Release 12.1(4)EA1

Table Of Contents

Unsupported CLI Commands in Release 12.1(4)EA1

FallBack Bridging

Unsupported Privileged EXEC Commands

Unsupported Global Configuration Commands

Unsupported Interface Configuration Commands

HSRP

Unsupported Interface Configuration Commands

Interface Configuration Commands

Unsupported Global Configuration Commands

IP Multicast Routing

Unsupported Privileged EXEC Commands

Unsupported Global Configuration Commands

Unsupported Interface Configuration Commands

MSDP

Unsupported Global Configuration Commands

IP Unicast Routing

Unsupported Privileged EXEC or User EXEC Commands

Unsupported Global Configuration Commands

Unsupported Interface Configuration Commands

Unsupported VPN Configuration Commands

Unsupported VRF Configuration Commands

Unsupported Route Map Commands


Unsupported CLI Commands in Release 12.1(4)EA1


This appendix lists some of the command-line interface (CLI) commands that are displayed when you enter the question mark (?) at the Catalyst 3550 switch prompt but are not supported in this release. The unsupported commands are listed by software feature and command mode.

FallBack Bridging

Unsupported Privileged EXEC Commands

clear bridge [bridge-group] multicast [router-ports | groups | counts] [group-address] [interface-unit] [counts]

clear vlan statistics

show bridge [bridge-group] circuit-group [circuit-group] [src-mac-address] [dst-mac-address]

show bridge [bridge-group] multicast [router-ports | groups] [group-address]

show bridge vlan

show interfaces crb

show interfaces {ethernet | fastethernet} [interface | slot/port] irb

show subscriber-policy range

Unsupported Global Configuration Commands

bridge bridge-group bitswap_l3_addresses

bridge bridge-group bridge ip

bridge bridge-group circuit-group circuit-group pause milliseconds

bridge bridge-group circuit-group circuit-group source-based

bridge cmf

bridge crb

bridge bridge-group domain domain-name

bridge irb

bridge bridge-group mac-address-table limit number

bridge bridge-group multicast-source

bridge bridge-group route protocol

bridge bridge-group subscriber policy policy

subscriber-policy policy [[no | default] packet [permit | deny]]

Unsupported Interface Configuration Commands

bridge-group bridge-group cbus-bridging

bridge-group bridge-group circuit-group circuit-number

bridge-group bridge-group input-address-list access-list-number

bridge-group bridge-group input-lat-service-deny group-list

bridge-group bridge-group input-lat-service-permit group-list

bridge-group bridge-group input-lsap-list access-list-number

bridge-group bridge-group input-pattern-list access-list-number

bridge-group bridge-group input-type-list access-list-number

bridge-group bridge-group lat-compression

bridge-group bridge-group output-address-list access-list-number

bridge-group bridge-group output-lat-service-deny group-list

bridge-group bridge-group output-lat-service-permit group-list

bridge-group bridge-group output-lsap-list access-list-number

bridge-group bridge-group output-pattern-list access-list-number

bridge-group bridge-group output-type-list access-list-number

bridge-group bridge-group sse

bridge-group bridge-group subscriber-loop-control

bridge-group bridge-group subscriber-trunk

bridge bridge-group lat-service-filtering

frame-relay map bridge dlci broadcast

interface bvi bridge-group

x25 map bridge x.121-address broadcast [options-keywords]

HSRP

Unsupported Interface Configuration Commands

standby mac-refresh seconds

standby use-bia

Interface Configuration Commands

Unsupported Global Configuration Commands

interface tunnel

IP Multicast Routing

Unsupported Privileged EXEC Commands

clear ip rtp header-compression [type number]

The debug ip packet command displays packets received by the switch CPU. It does not display packets that are hardware-switched.

The debug ip mcache command affects packets received by the switch CPU. It does not display packets that are hardware-switched.

The debug ip mpacket [detail] [access-list-number [group-name-or-address] command affects only packets received by the switch CPU. Because most multicast packets are hardware-switched, use this command only when you know that the route will forward the packet to the CPU.

debug ip pim atm

show frame-relay ip rtp header-compression [interface type number]

The show ip mcache command displays entries in the cache for those packets that are sent to the switch CPU. Because most multicast packets are switched in hardware without CPU involvement, you can use this command, but multicast packet information is not displayed.

The show ip mpacket commands are supported but are only useful for packets received at the switch CPU. If the route is hardward-switched, the command has no effect because the CPU does not receive the packet and cannot display it.

show ip pim vc [group-address | name] [type number]

show ip rtp header-compression [type number] [detail]

Unsupported Global Configuration Commands

ip pim accept-rp {address | auto-rp} [group-access-list-number]

ip pim message-interval seconds

Unsupported Interface Configuration Commands

frame-relay ip rtp header-compression [active | passive]

frame-relay map ip ip-address dlci [broadcast] compress

frame-relay map ip ip-address dlci rtp header-compression [active | passive]

ip igmp helper-address ip-address

ip multicast helper-map {group-address | broadcast} {broadcast-address | multicast-address} extended-access-list-number

ip multicast rate-limit {in | out} [video | whiteboard] [group-list access-list] [source-list access-list] kbps

ip multicast use-functional

ip pim minimum-vc-rate pps

ip pim multipoint-signalling

ip pim nbma-mode

ip pim vc-count number

ip rtp compression-connections number

ip rtp header-compression [passive]

MSDP

Unsupported Global Configuration Commands

ip msdp default-peer ip-address | name [prefix-list list] (Because BGP/MBGP is not supported, use the ip msdp peer command instead of this command.)

IP Unicast Routing

Unsupported Privileged EXEC or User EXEC Commands

clear ip accounting [checkpoint]

show cef [drop | not-cef-switched]

show ip vrf [{brief | detail | interfaces}] [vrf-name] [output-modifiers]

show ip accounting [checkpoint] [output-packets | access-violations]

Unsupported Global Configuration Commands

ip accounting-list ip-address wildcard

ip accounting-transits count

ip cef accounting [per-prefix] [non-recursive]

ip cef traffic-statistics [load-interval seconds] [update-rate seconds]]

ip flow-aggregation

ip flow-cache

ip flow-export

ip gratituitous-arps

ip local

ip reflexive-list

ip vrf

router bgp

router egp

router-isis

router iso-igrp

router mobile

router odr

router static

Unsupported Interface Configuration Commands

ip accounting

ip load-sharing [per-packet]

ip mtu bytes

ip route-cache

ip verify

ip vrf

ip unnumbered type number

All ip security commands

Unsupported VPN Configuration Commands

All

Unsupported VRF Configuration Commands

All

Unsupported Route Map Commands

set automatic-tag

set ip destination ip-address mask

set ip next-hop ip-address [...ip-address]

set ip next-hop peer-address

set ip precedence value

set ip qos-group

set tag tag-value