Catalyst 3550 Multilayer Switch Software Configuration Guide, 12.1(13)EA1
Unsupported CLI Commands for Release 12.1(13)EA1
Downloads: This chapterpdf (PDF - 199.0KB) The complete bookPDF (PDF - 11.03MB) | Feedback

Unsupported CLI Commands in Release 12.1(13)EA1

Table Of Contents

Unsupported CLI Commands in Release 12.1(13)EA1

Access Control Lists

Unsupported Privileged EXEC Commands

ARP Commands

Unsupported Global Configuration Commands

Unsupported Interface Configuration Commands

FallBack Bridging

Unsupported Privileged EXEC Commands

Unsupported Global Configuration Commands

Unsupported Interface Configuration Commands

HSRP

Unsupported Global Configuration Commands

Unsupported Interface Configuration Commands

Interface Configuration Commands

IP Multicast Routing

Unsupported Privileged EXEC Commands

Unsupported Global Configuration Commands

Unsupported Interface Configuration Commands

IP Unicast Routing

Unsupported Privileged EXEC or User EXEC Commands

Unsupported Global Configuration Commands

Unsupported Interface Configuration Commands

Unsupported BGP Router Configuration Commands

Unsupported VPN Configuration Commands

Unsupported Route Map Commands

MSDP

Unsupported Privileged EXEC Commands

Unsupported Global Configuration Commands

RADIUS

Unsupported Global Configuration Commands

SNMP

Unsupported Global Configuration Commands

Spanning Tree

Unsupported Global Configuration Commands

VLAN

Unsupported User EXEC Commands


Unsupported CLI Commands in Release 12.1(13)EA1


This appendix lists some of the command-line interface (CLI) commands that are displayed when you enter the question mark (?) at the Catalyst 3550 switch prompt but are not supported in this release, either because they are not tested, or because of Catalyst 3550 hardware limitations. This is not a complete list. The unsupported commands are listed by software feature and command mode.

Access Control Lists

Unsupported Privileged EXEC Commands

access-enable [host] [timeout minutes]

access-template [access-list-number | name] [dynamic-name] [source] [destination] [timeout minutes]

clear access-template [access-list-number | name] [dynamic-name] [source] [destination].

ARP Commands

Unsupported Global Configuration Commands

arp ip-address hardware-address smds

arp ip-address hardware-address srp-a

arp ip-address hardware-address srp-b

Unsupported Interface Configuration Commands

arp probe

ip probe proxy

FallBack Bridging

Unsupported Privileged EXEC Commands

clear bridge [bridge-group] multicast [router-ports | groups | counts] [group-address] [interface-unit] [counts]

clear vlan statistics

show bridge [bridge-group] circuit-group [circuit-group] [src-mac-address] [dst-mac-address]

show bridge [bridge-group] multicast [router-ports | groups] [group-address]

show bridge vlan

show interfaces crb

show interfaces {ethernet | fastethernet} [interface | slot/port] irb

show subscriber-policy range

Unsupported Global Configuration Commands

bridge bridge-group bitswap_l3_addresses

bridge bridge-group bridge ip

bridge bridge-group circuit-group circuit-group pause milliseconds

bridge bridge-group circuit-group circuit-group source-based

bridge cmf

bridge crb

bridge bridge-group domain domain-name

bridge irb

bridge bridge-group mac-address-table limit number

bridge bridge-group multicast-source

bridge bridge-group route protocol

bridge bridge-group subscriber policy policy

subscriber-policy policy [[no | default] packet [permit | deny]]

Unsupported Interface Configuration Commands

bridge-group bridge-group cbus-bridging

bridge-group bridge-group circuit-group circuit-number

bridge-group bridge-group input-address-list access-list-number

bridge-group bridge-group input-lat-service-deny group-list

bridge-group bridge-group input-lat-service-permit group-list

bridge-group bridge-group input-lsap-list access-list-number

bridge-group bridge-group input-pattern-list access-list-number

bridge-group bridge-group input-type-list access-list-number

bridge-group bridge-group lat-compression

bridge-group bridge-group output-address-list access-list-number

bridge-group bridge-group output-lat-service-deny group-list

bridge-group bridge-group output-lat-service-permit group-list

bridge-group bridge-group output-lsap-list access-list-number

bridge-group bridge-group output-pattern-list access-list-number

bridge-group bridge-group output-type-list access-list-number

bridge-group bridge-group sse

bridge-group bridge-group subscriber-loop-control

bridge-group bridge-group subscriber-trunk

bridge bridge-group lat-service-filtering

frame-relay map bridge dlci broadcast

interface bvi bridge-group

x25 map bridge x.121-address broadcast [options-keywords]

HSRP

Unsupported Global Configuration Commands

interface Async

interface BVI

interface Dialer

interface Group-Async

interface Lex

interface Multilink

interface Virtual-Template

interface Virtual-Tokenring

Unsupported Interface Configuration Commands

mtu

standby mac-refresh seconds

standby use-bia

Interface Configuration Commands

switchport broadcast level

switchport multicast level

switchport unicast level


Note These commands were replaced in IOS release 12.1(8)EA1 by the storm-control {broadcast | multicast | unicast} level level [.level] interface configuration command.


IP Multicast Routing

Unsupported Privileged EXEC Commands

clear ip rtp header-compression [type number]

The debug ip packet command displays packets received by the switch CPU. It does not display packets that are hardware-switched.

The debug ip mcache command affects packets received by the switch CPU. It does not display packets that are hardware-switched.

The debug ip mpacket [detail] [access-list-number [group-name-or-address] command affects only packets received by the switch CPU. Because most multicast packets are hardware-switched, use this command only when you know that the route will forward the packet to the CPU.

debug ip pim atm

show frame-relay ip rtp header-compression [interface type number]

The show ip mcache command displays entries in the cache for those packets that are sent to the switch CPU. Because most multicast packets are switched in hardware without CPU involvement, you can use this command, but multicast packet information is not displayed.

The show ip mpacket commands are supported but are only useful for packets received at the switch CPU. If the route is hardward-switched, the command has no effect because the CPU does not receive the packet and cannot display it.

show ip pim vc [group-address | name] [type number]

show ip rtp header-compression [type number] [detail]

Unsupported Global Configuration Commands

ip pim accept-rp {address | auto-rp} [group-access-list-number]

ip pim message-interval seconds

Unsupported Interface Configuration Commands

frame-relay ip rtp header-compression [active | passive]

frame-relay map ip ip-address dlci [broadcast] compress

frame-relay map ip ip-address dlci rtp header-compression [active | passive]

ip igmp helper-address ip-address

ip multicast helper-map {group-address | broadcast} {broadcast-address | multicast-address} extended-access-list-number

ip multicast rate-limit {in | out} [video | whiteboard] [group-list access-list] [source-list access-list] kbps

ip multicast use-functional

ip pim minimum-vc-rate pps

ip pim multipoint-signalling

ip pim nbma-mode

ip pim vc-count number

ip rtp compression-connections number

ip rtp header-compression [passive]

IP Unicast Routing

Unsupported Privileged EXEC or User EXEC Commands

clear ip accounting [checkpoint]

clear ip bgp address flap-statistics

clear ip bgp prefix-list

show cef [drop | not-cef-switched]

show ip accounting [checkpoint] [output-packets | access-violations]

show ip bgp dampened-paths

show ip bgp flap-statistics

show ip bgp inconsistent-as

show ip bgp regexp regular expression

Unsupported Global Configuration Commands

ip accounting-list ip-address wildcard

ip accounting-transits count

ip cef accounting [per-prefix] [non-recursive]

ip cef traffic-statistics [load-interval seconds] [update-rate seconds]]

ip flow-aggregation

ip flow-cache

ip flow-export

ip gratituitous-arps

ip local

ip reflexive-list

router egp

router-isis

router iso-igrp

router mobile

router odr

router static

Unsupported Interface Configuration Commands

ip accounting

ip load-sharing [per-packet]

ip mtu bytes

ip route-cache

ip verify

ip unnumbered type number

All ip security commands

Unsupported BGP Router Configuration Commands


Note These BGP commands have not been tested for the Catalyst 3550 and are not supported for the switch in Cisco IOS release 12.1(12c)EA1. This is not a complete list.


address-family vpnv4

default-information originate

neighbor advertise-map

neighbor allowas-in

neighbor default-originate

neighbor description

network backdoor

table-map

Unsupported VPN Configuration Commands

All


Note The switch does support multi-VPN routing/forwarding (multi-VRF) commands shown in the command reference for this release.


Unsupported Route Map Commands

match length

route-map map-tag deny

set automatic-tag

set dampening half-life reuse suppress max-suppress-time

set default interface

set interface

set ip default next-hop

set ip destination ip-address mask

set ip df

set ip precedence value

set ip qos-group

set tag tag-value

set ip tos

MSDP

Unsupported Privileged EXEC Commands

show access-expression

show exception

show location

show pm LINE

show smf [interface-id]

show subscriber-policy [policy-number]

show template [template-name]

Unsupported Global Configuration Commands

ip msdp default-peer ip-address | name [prefix-list list] (Because BGP/MBGP is not supported, use the ip msdp peer command instead of this command.)

RADIUS

Unsupported Global Configuration Commands

aaa nas port extended

radius-server attribute nas-port

radius-server configure

radius-server extended-portnames

SNMP

Unsupported Global Configuration Commands

snmp-server enable informs

Spanning Tree

Unsupported Global Configuration Commands

spanning-tree etherchannel guard misconfig

VLAN

Unsupported User EXEC Commands

ifindex

private-vlan