Catalyst 2950 and Catalyst 2955 Switch Software Configuration Guide, 12.1(22)EA11 and Later
Supported MIBs
Downloads: This chapterpdf (PDF - 88.0KB) The complete bookPDF (PDF - 18.87MB) | Feedback

Supported MIBs

Table Of Contents

Supported MIBs

MIB List

Using FTP to Access the MIB Files


Supported MIBs


This appendix lists the supported MIBs for this release. It contains these sections:

MIB List

Using FTP to Access the MIB Files

MIB List


Note The Catalyst 2955 switch supports the ENTITY-MIB, CISCO-ENVMON-MIB and CISCO-ENTITY-ALARM-MIB.


BRIDGE-MIB (RFC1493)

CISCO-2900-MIB

CISCO-BULK-FILE-MIB

CISCO-CDP-MIB

CISCO-CLUSTER-MIB

CISCO_CONFIG_COPY_MIB

CISCO-CONFIG-MAN-MIB

CISCO-ENTITY-MIB

CISCO-ENTITY-ALARM-MIB (Catalyst 2955 only)

CISCO-ENTITY-VENDORTYPE-OID-MIB

CISCO_ENVMON_MIB

CISCO-FLASH-MIB

CISCO-FTP-CLIENT-MIB

CISCO-IETF-VDSL-LINE-MIB (Catalyst 2950 Long-Reach Ethernet [LRE] only)

CISCO-IGMP-FILTER-MIB

CISCO-IMAGE-MIB

CISCO-LRE-CPR-MIB (Catalyst 2950 LRE only)

CISCO-MAC-NOTIFICATION-MIB

CISCO-MEMORY-POOL-MIB

CISCO-PAE-MIB

CISCO-PAGP-MIB

CISCO-PING-MIB

CISCO-PORT-SECURITY-MIB

CISCO-PROCESS-MIB

CISCO-PRODUCTS-MIB

CISCO-RTTMON-MIB (subsystems supported: sub_rtt_rmon and sub_rtt_rmonlib)

CISCO-SMI

CISCO_STACKMAKER_MIB

CISCO-STP-EXTENSIONS-MIB

CISCO-SYSLOG-MIB

CISCO-TC

CISCO-TCP-MIB

CISCO-VLAN-MEMBERSHIP-MIB

CISCO-VTP-MIB

ENTITY-MIB

IEEE8021-PAE-MIB

IANAifType-MIB

IF-MIB (RFC 1573)

OLD-CISCO-CHASSIS-MIB

OLD-CISCO-CPU-MIB

OLD-CISCO-INTERFACES-MIB

OLD-CISCO-IP-MIB

OLD-CISCO-MEMORY-MIB

OLD-CISCO-SYSTEM-MIB

OLD-CISCO-TCP-MIB

OLD-CISCO-TS-MIB

RFC1213-MIB

RMON-MIB (RFC 1757)

RFC1398-MIB

RS-232-MIB

SNMPv2-MIB

SNMPv2-SMI

SNMPv2-TC

TCP-MIB

UDP-MIB


Note The IF-MIB and the CISCO-IETF-VDSL-LINE-MIB are supported as read-only MIBs for the Fast Ethernet interfaces on the CPE devices.


Using FTP to Access the MIB Files

You can get each MIB file by using this procedure:


Step 1 Make sure that your FTP client is in passive mode.


Note Some FTP clients do not support passive mode.


Step 2 Use FTP to access the server ftp.cisco.com.

Step 3 Log in with the username anonymous.

Step 4 Enter your e-mail username when prompted for the password.

Step 5 At the ftp> prompt, change directories to /pub/mibs/v1 and the /pub/mibs/v2.

Step 6 Use the get MIB_filename command to obtain a copy of the MIB file.


You can also access information about MIBs on the Cisco website:

http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml