Catalyst 2950 and Catalyst 2955 Switch Software Configuration Guide, 12.1(19)EA1
Configuring DHCP Features
Downloads: This chapterpdf (PDF - 211.0KB) The complete bookPDF (PDF - 8.32MB) | Feedback

Configuring DHCP Features

Table Of Contents

Configuring DHCP Features

Understanding DHCP Features

DHCP Snooping

Option-82 Data Insertion

Configuring DHCP Features

Default DHCP Configuration

DHCP Snooping Configuration Guidelines

Enabling DHCP Snooping and Option 82

Displaying DHCP Information

Displaying a Binding Table

Displaying the DHCP Snooping Configuration


Configuring DHCP Features


This chapter describes how to configure Dynamic Host Configuration Protocol (DHCP) snooping and the option-82 data insertion features on the Catalyst 2950 or Catalyst 2955 switch. To use the features described in this chapter, you must have the enhanced software image (EI) installed on your switch.


Note For complete syntax and usage information for the commands used in this chapter, see the command reference for this release, and refer to the "IP Addressing and Services" section in the Cisco IOS IP and IP Routing Command Reference for Release 12.1.


This chapter consists of these sections:

Understanding DHCP Features

Configuring DHCP Features

Displaying DHCP Information

Understanding DHCP Features

DHCP is widely used in LAN environments to dynamically assign host IP addresses from a centralized server, which significantly reduces the overhead of administration of IP addresses. DHCP also helps conserve the limited IP address space because IP addresses no longer need to be permanently assigned to hosts; only those hosts that are connected to the network consume IP addresses.

DHCP Snooping

DHCP snooping is a DHCP security feature that provides network security by filtering untrusted DHCP messages and by building and maintaining a DHCP snooping binding table. An untrusted message is a message that is received from outside the network or firewall that can cause traffic attacks within your network.

The DHCP snooping binding table contains the MAC address, IP address, lease time, binding type, VLAN number, and interface information that corresponds to the local untrusted interfaces of a switch; it does not contain information regarding hosts interconnected with a trusted interface. An untrusted interface is an interface that is configured to receive messages from outside the network or firewall. A trusted interface is an interface that is configured to receive only messages from within the network.

DHCP snooping acts like a firewall between untrusted hosts and DHCP servers. It also gives you a way to differentiate between untrusted interfaces connected to the end user and trusted interfaces connected to the DHCP server or another switch.

Option-82 Data Insertion

In residential, metropolitan Ethernet-access environments, DHCP can centrally manage the IP address assignments for a large number of subscribers. When the DHCP option-82 feature is enabled on the switch, a subscriber is identified by the switch port through which it connects to the network (in addition to its MAC address). Multiple hosts on the subscriber LAN can be connected to the same port on the access switch and are uniquely identified.

Figure 20-1 is an example of a metropolitan Ethernet network in which a centralized DHCP server assigns IP addresses to subscribers connected to the switch at the access layer. Because the DHCP clients and their associated DHCP server do not reside on the same IP network or subnet, a DHCP relay agent (the Catalyst switch) is configured with a helper address to enable broadcast forwarding and to transfer DHCP messages between the clients and the server.

Figure 20-1 DHCP Relay Agent in a Metropolitan Ethernet Network

When you enable the DHCP snooping information option 82 on the switch, this sequence of events occurs:

The host (DHCP client) generates a DHCP request and broadcasts it on the network.

When the switch receives the DHCP request, it adds the option-82 information in the packet. The option-82 information contains the switch MAC address (the remote ID suboption) and the port identifier, vlan-mod-port, from which the packet is received (the circuit ID suboption).

The switch forwards the DHCP request that includes the option-82 field to the DHCP server.

The DHCP server receives the packet. If the server is option-82 capable, it can use the remote ID, the circuit ID, or both to assign IP addresses and implement policies, such as restricting the number of IP addresses that can be assigned to a single remote ID or a circuit ID. Then the DHCP server echoes the option-82 field in the DHCP reply.

The DHCP server unicasts the reply to the switch if the request was relayed to the server by the switch. When the client and server are on the same subnet, the server broadcasts the reply. The switch verifies that it originally inserted the option-82 data by inspecting the remote ID and possibly the circuit ID fields. The switch removes the option-82 field and forwards the packet to the switch port that connects to the DHCP client that sent the DHCP request.

Configuring DHCP Features

These sections describe how to configure DHCP snooping and option 82 on your switch:

Default DHCP Configuration

DHCP Snooping Configuration Guidelines

Enabling DHCP Snooping and Option 82

Default DHCP Configuration

Table 20-1 shows the default DHCP configuration.

Table 20-1 Default DHCP Configuration

Feature
Default Setting

DHCP snooping enabled globally

Disabled

DHCP snooping information option

Enabled

DHCP snooping limit rate

None configured

DHCP snooping trust

Untrusted

DHCP snooping VLAN

Disabled


DHCP Snooping Configuration Guidelines

These are the configuration guidelines for DHCP snooping.

You must globally enable DHCP snooping on the switch.

DHCP snooping is not active until DHCP snooping is enabled on a VLAN.

Before configuring the DHCP information option on your switch, make sure to configure the device that is acting as the DHCP server. For example, you must specify the IP addresses that the DHCP server can assign or exclude or configure DHCP options for devices.

If your switch is the DHCP server, see the "Configuring the DHCP Server" section for more information.

If your DHCP server is a Cisco device, refer to the "IP Addressing and Services" section in the "Configuring DHCP" chapter of the Cisco IOS IP and IP Routing Configuration Guide for Release 12.1. Otherwise, refer to the documentation that shipped with the server.

Enabling DHCP Snooping and Option 82

Beginning in privileged EXEC mode, follow these steps to enable DHCP snooping on the switch.

 
Command
Purpose

Step 1 

configure terminal

Enter global configuration mode.

Step 2 

ip dhcp snooping

Enable DHCP snooping globally.

Step 3 

ip dhcp snooping vlan vlan-id [vlan-id]

Enable DHCP snooping on a VLAN or range of VLANs. You can specify a single VLAN identified by VLAN ID number or start and end VLAN IDs to specify a range of VLANs. The range is 1 to 4094.

Step 4 

ip dhcp snooping information option

Enable the switch to insert and remove DHCP relay information (option-82 field) in forwarded DHCP request messages to the DHCP server.

The default is enabled.

Step 5 

interface interface-id

Enter interface configuration mode, and specify the interface to be configured.

Step 6 

ip dhcp snooping trust

(Optional) Configure the interface as trusted or untrusted. You can use the no keyword to configure an interface to receive messages from an untrusted client. The default is untrusted.

Step 7 

ip dhcp snooping limit rate rate

(Optional) Configure the number of DHCP packets per second than an interface can receive. The range is 1 to 4294967294. The default is no rate limit configured.

Note We recommend an untrusted rate limit of not more than 100 packets per second. Normally, the rate limit applies to untrusted interfaces. If you configure rate limiting for trusted interfaces, you will need to adjust the rate limit to a higher value because trusted interfaces might aggregate DHCP traffic in the switch.

Step 8 

end

Return to privileged EXEC mode.

Step 9 

show running-config

Verify your entries.

Step 10 

copy running-config startup-config

(Optional) Save your entries in the configuration file.

To disable DHCP snooping, use the no ip dhcp snooping global configuration command. To disable DHCP snooping on a VLAN or range of VLANs, use the no ip dhcp snooping vlan vlan-id global configuration command. To disable the insertion and removal of the option-82 field, use the no ip dhcp snooping information option global configuration command.

This example shows how to enable DHCP snooping globally and on VLAN 10 and to configure a rate limit of 100 packets per second on Fast Ethernet port 0/1:

Switch(config)# ip dhcp snooping
Switch(config)# ip dhcp snooping vlan 10
Switch(config)# ip dhcp snooping information option
Switch(config)# interface fastethernet0/1
Switch(config-if)# ip dhcp snooping limit rate 100

Displaying DHCP Information

You can display a DHCP snooping binding table and configuration information for all interfaces on a switch.

Displaying a Binding Table

The DHCP snooping binding table for each switch has binding entries that correspond to untrusted ports. The table does not have information about hosts interconnected with a trusted port because each interconnected switch has its own DHCP snooping binding table.

This example shows how to display the DHCP snooping binding entries for a switch.

Switch# show ip dhcp snooping binding
MacAddress          IpAddress        Lease(sec)  Type     VLAN  Interface
------------------  ---------------  ----------  -------  ----  --------------------
00:30:94:C2:EF:35   41.0.0.51        286         dynamic  41    FastEthernet0/3
00:D0:B7:1B:35:DE   41.0.0.52        237         dynamic  41    FastEthernet0/3
00:00:00:00:00:01   40.0.0.46        286         dynamic  40    FastEthernet0/9
00:00:00:00:00:03   42.0.0.33        286         dynamic  42    FastEthernet0/9
00:00:00:00:00:02   41.0.0.53        286         dynamic  41    FastEthernet0/9

Table 20-2 describes the fields in the show ip dhcp snooping binding command output.

Table 20-2 show ip dhcp snooping binding Command Output 

Field
Description

MAC Address

Client hardware MAC address

IP Address

Client IP address assigned from the DHCP server

Lease (seconds)

IP address lease time

Type

Binding type; dynamic binding learned by DHCP-snooping or statically configured binding

VLAN

VLAN number of the client interface

Interface

Interface that connects to the DHCP client host


Displaying the DHCP Snooping Configuration

This example shows how to display the DHCP snooping configuration for a switch.

Switch# show ip dhcp snooping
Switch DHCP snooping is enabled
DHCP snooping is configured on following VLANs:
40-42
Insertion of option 82 is enabled
Interface                    Trusted     Rate limit (pps)
------------------------     -------     ----------------
FastEthernet0/5              yes         unlimited
FastEthernet0/7              yes         unlimited
FastEthernet0/3              no          5000     
FastEthernet0/5              yes         unlimited
FastEthernet0/7              yes         unlimited
FastEthernet0/5              yes         unlimited
FastEthernet0/7              yes         unlimited