Cisco Virtual Security Gateway, Rel. 4.2(1)VSG1(2) and Cisco Virtual Network Management Center, Rel. 1.2 Installation and Upgrade
Overview
Downloads: This chapterpdf (PDF - 499.0KB) The complete bookPDF (PDF - 4.95MB) | Feedback

Overview

Table Of Contents

Overview

Information About Installing the Cisco Virtual Network Management Center and the Cisco Virtual Security Gateway

Information About Cisco Virtual Security Gateway

VNMC and VSG Architecture

Trusted Multitenant Access

Dynamic (Virtualization-Aware) Operation

Setting Up the Cisco VSGs and VLANs

Information About the Cisco Virtual Network Management Center

Cisco VNMC Components

Cisco VNMC Key Benefits

Cisco VNMC Architecture

Cisco VNMC Security

Cisco VNMC API

Cisco VNMC and VSM

System Requirements

Information About High Availability


Overview


This chapter provides information about the Cisco Virtual Security Gateway (Cisco VSG) and the Cisco Virtual Network Management Center (Cisco VNMC). It also provides information about High Availability (HA).

This chapter includes the following sections:

Information About Installing the Cisco Virtual Network Management Center and the Cisco Virtual Security Gateway

Information About Cisco Virtual Security Gateway

Information About the Cisco Virtual Network Management Center

Information About High Availability

Information About Installing the Cisco Virtual Network Management Center and the Cisco Virtual Security Gateway

You must install the Cisco Virtual Network Management Center (Cisco VNMC) and the Cisco Virtual Security Gateway (Cisco VSG) in a particular sequence on the Cisco Nexus 1000V switch in order to have a functioning virtual system. Part 1, the Quick Start Guide for Cisco Virtual Security Gateway and Cisco Virtual Network Management Center, provides that critical sequence information that you need for a successful installation on the Cisco Nexus 1000v switch. Part 4, Installing VSG on a Cisco Nexus 1010, provides the information required for installing the Cisco VSG on the Cisco Nexus 1010 Virtual Services Appliance.

Information About Cisco Virtual Security Gateway

The Cisco Virtual Security Gateway (VSG) is a virtual firewall appliance that provides trusted access to virtual data center and cloud environments with dynamic policy-driven operation, mobility-transparent enforcement, and scale-out deployment for dense multitenancy. By associating one or more virtual machines (VMs) into distinct trust zones, the Cisco VSG ensures that access to trust zones is controlled and monitored through established security policies. Figure 1-1 shows the trusted zone-based access control that is used in per-tenant enforcement with the Cisco VSG.

Figure 1-1 Trusted Zone-Based Access Control Using Per-Tenant Enforcement with the Cisco VSG

VNMC and VSG Architecture

The Cisco VSG operates with the Cisco Nexus 1000VSeries switch in the VMware vSphere Hypervisor or the Cisco Nexus 1010 Virtual Services Appliance, and the Cisco VSG leverages the virtual network service data path (vPath) (see Figure 1-2). vPath steers traffic, whether external to VM or VM to VM, to the Cisco VSG of a tenant. Initial packet processing occurs in the Cisco VSG for policy evaluation and enforcement. After the policy decision is made, the Cisco VSG offloads policy enforcement of the remaining packets to vPath.

vPath supports the following features:

Tenant-aware flow classification and subsequent redirection to a designated Cisco VSG tenant

Per-tenant policy enforcement of flows offloaded by Cisco VSG to vPath

The Cisco VSG and the VEM provide the following benefits (see Figure 1-3):

Each Cisco VSG can provide protect ionacross multiple physical servers, which eliminates the need for you to deploy a virtual appliance per physical server.

By offloading the fast-path to one or more VEM vPath modules, the Cisco VSG enhances security performance through distributed vPath-based enforcement.

You can use the Cisco VSG without creating multiple switches or temporarily migrating VMs to different switches or servers. Zone scaling, which is based on security profiles, simplifies physical server upgrades without compromising security or incurring application outages.

For each tenant, you can deploy the Cisco VSG in an active-standby mode to ensure that vPath redirects packets to the standby Cisco VSG when the primary Cisco VSG is unavailable.

You can place the Cisco VSG on a dedicated server so that you can allocate the maximum compute capacity to application workloads. This feature enables capacity planning to occur independently, and allows for operational segregation across security, network, and server groups.

Figure 1-2 Cisco Virtual Security Gateway Deployment Topology

Trusted Multitenant Access

You can transparently insert a Cisco VSG into the VMware vSphere environment where the Cisco Nexus 1000V is deployed. One or more instances of the Cisco VSG is deployed on a per-tenant basis, which allows a highly scale-out deployment across many tenants. Tenants are isolated from each other, so no traffic can cross tenant boundaries. You can deploy a Cisco VSG at the tenant level, at the virtual data center (vDC) level or at the vApp level.

As you instantiate VMs for a given tenant, their association to security profiles (or zone membership) occurs immediately through binding with the Cisco Nexus 1000V port profile. Each VM is placed upon instantiation into a logical trust zone (see Figure 1-2). Security profiles contain context-aware rule sets that specify access policies for traffic that enters and exits each zone. In addition to VM and network contexts, security administrators can also leverage custom attributes that define zones directly through security profiles. You can apply controls to zone-to-zone traffic and to external-to-zone (and zone-to-external) traffic. Zone-based enforcement occurs within a VLAN because a VLAN often identifies a tenant boundary. The Cisco VSG evaluates access control rules and then offloads enforcement to the Cisco Nexus 1000V VEM vPath module. Upon enforcement, the Cisco VSG can permit or deny access and can generate optional access logs. Cisco VSG also provides policy-based traffic monitoring capability with access logs.

Dynamic (Virtualization-Aware) Operation

A virtualization environment is dynamic, where frequent additions, deletions, and changes occur across tenants and across VMs. Live migration of VMs can occur due to manual or programmatic vMotion events. Figure 1-3 shows how a structured environment of Figure 1-2 can change over time due to this dynamic VM environment.

Figure 1-3 Cisco VSG Security in a Dynamic VM Environment, Including VM Live Migration

The Cisco VSG operating with the Cisco Nexus 1000V (and vPath) supports a dynamic VM environment. When you create a tenant with the Cisco VSG (standalone or active-standby pair) on the Cisco Virtual Network Management Center (Cisco VNMC), associated security profiles are defined that include trust zone definitions and access control rules. Each security profile is bound to a Cisco Nexus 1000V port profile (authored on the Cisco Nexus 1000V Virtual Supervisor Module (VSM) and published to the VMware Virtual Center [vCenter]).

When a new VM is instantiated, the server administrator assigns appropriate port profiles to the virtual Ethernet port of the VM. Because the port profile uniquely refers to a security profile and VM zone membership, the Cisco VSG immediately applies the security controls. You can repurpose a VM by assigning it to a different port profile or security profile.

As vMotion events are triggered, VMs move across physical servers. Because the Cisco Nexus 1000V ensures that port profile policies follow the VMs, associated security profiles also follow these moving VMs, and security enforcement and monitoring remain transparent to vMotion events.

Setting Up the Cisco VSGs and VLANs

You can set up a Cisco VSG in an overlay fashion so that VMs can reach a Cisco VSG irrespective of its location. The vPath component in the Cisco Nexus 1000V VEM intercepts the packets from the VM and sends them to the Cisco VSG for further processing.

Figure 1-4 shows Cisco VSGs in a typical arrangement. In the figure, the Cisco VSG connects to three different VLANs (service VLAN, management VLAN, and HA VLAN). A Cisco VSG is configured with three vNICS—data vNIC (1), management vNIC (2), and HA vNIC (3)—with each of the vNICs connected to one of the VLANs through a port profile. The VLAN functions are as follows:

The service VLAN provides communications between the Cisco Nexus 1000V VEM and Cisco VSGs. All the Cisco VSG data interfaces are part of the service VLAN and the VEM uses this VLAN for its interaction with Cisco VSGs.

The management VLAN connects the management platforms such as the VMware vCenter, the Cisco Virtual Network Management Center, and the Cisco Nexus 1000V VSM and the managed Cisco VSGs. The Cisco VSG management vNIC is part of the management VLAN.

The HA VLAN provides the heart-beat mechanism and identifies the active and standby relationship between the VSGs. The Cisco VSG vNICs are part of the HA VLAN.

You can allocate one or more VM data VLANs for VM-to-VM communications. In a typical multitenant environment, the management VLAN is shared among all the tenants, and the service VLAN, HA VLAN, and the VM data VLAN are allocated on a per-tenant basis. However, when VLAN resources become scarce, you might decide to use a single VLAN for service and HA functions.

Figure 1-4 Cisco Virtual Security Gateway VLAN Usages

Information About the Cisco Virtual Network Management Center

The Cisco VNMC virtual appliance is based on Red Hat Enterprise Linux (RHEL), that provides centralized device and security policy management of the Cisco Virtual Security Gateway (VSG) for the Cisco Nexus 1000V Series switch. Designed for multitenant operation, Cisco VNMC provides seamless, scalable, and automation-centric management for virtual data center and cloud environments. With a web-based GUI, CLI, and XML APIs, the Cisco VNMC enables you to manage Cisco VSGs that are deployed throughout the data center from a centralized location.


Note Multitenancy is when a single instance of the software runs on a Software-as-a-Service (SaaS) server, serving multiple client organizations or tenants. In contrast, multi-instance architecture has separate software instances set up for different client organizations. With a multitenant architecture, a software application can virtually partition data and configurations so that each tenant works with a customized virtual application instance.


The Cisco VNMC is built on an information model-driven architecture, where each managed device is represented by its subcomponents.

This section includes the following topics:

Cisco VNMC Components

System Requirements

Cisco VNMC Components

This section includes the following topics:

Cisco VNMC Key Benefits

Cisco VNMC Architecture

Cisco VNMC Security

Cisco VNMC API

Cisco VNMC and VSM

Figure 1-5 shows the Cisco VNMC components.

Figure 1-5 Cisco VNMC Components

Cisco VNMC Key Benefits

The Cisco VNMC provides the following key benefits:

Rapid and scalable deployment with dynamic, template-driven policy management based on security profiles.

Seamless operational management through XML APIs that enable integration with third-party management tools.

Greater collaboration across security and server administrators, while maintaining administrative separation and reducing administrative errors.

Cisco VNMC Architecture

The Cisco VNMC architecture includes the following components:

A centralized repository for managing security policies (security templates) and object configurations that allow managed devices to be stateless.

A centralized resource management function that manages pools of devices that are commissioned and pools of devices that are available for commissioning. This function simplifies large scale deployments as follows:

Devices can be preinstantiated and then configured on demand

Devices can be allocated and deallocated dynamically across commissioned and noncommissioned pools

A distributed management-plane function that uses an embedded management agent on each device that allows for a scalable management framework.

Cisco VNMC Security

The Cisco VNMC uses security profiles for tenant-centric template-based configuration of security policies. A security profile is a collection of security policies that are predefined and applied on an on-demand basis at the time of virtual machine (VM) instantiation. These profiles simplify authoring, deployment, and management of security policies in a dense multitenant environment, reduce administrative errors, and simplify audits.

Cisco VNMC API

The Cisco VNMC API allows you to coordinate with third-party provisioning tools for programmatic provisioning and management of Cisco VSGs. This feature allows you to simplify data center operational processes and reduce the cost of infrastructure management.

Cisco VNMC and VSM

The Cisco VNMC operates with the Cisco Nexus 1000V Virtual Supervisor Module (VSM) to achieve the following scenarios:

Security administrators who author and manage security profiles as well as manage Cisco VSG instances. Security profiles are referenced in Cisco Nexus 1000V port profiles through the Cisco VNMC interface.

Network administrators who author and manage port profiles as well as manage Cisco Nexus 1000V switches. Port profiles are referenced in vCenter through the Cisco Nexus 1000V VSM interface.

Server administrators who select the appropriate port profiles in the vCenter when instantiating a virtual machine.

System Requirements

System requirements for a Cisco VNMC are as follows:

x86 Intel or AMD server with a 64-bit processor listed in the VMware compatibility matrix

Intel VT that is enabled in the BIOS

VMware ESX 4.0, 4.0 U1, 4.0 U2, or 4.1

VMware vSphere Hypervisor

VMware vCenter 4.0, 4.0 U1, 4.0 U2, or 4.1

2-GB memory reserved for each Cisco VNMC installation

Datastore with at least 25-GB disk space available on shared Network File System/Storage Area Network (NFS/SAN) storage when the Cisco VNMC is deployed in an HA cluster

Internet Explorer 7.0 or Mozilla Firefox 3.6.x on Windows

Flash 10.0 or 10.1


Note If you are running Firefox or IE and do not have Flash, or you have a version of Flash that is older than 10.1, a message displays asking you to install Flash and provides a link to the Adobe website.



Note You can find VMware compatibility guides at http://www.vmware.com/resources/compatibility/search.php


Information About High Availability

VMware high availability (HA) provides a base level of protection for a Cisco VNMC VM by restarting it on another host in the HA cluster. With VMware HA, data is protected through a shared storage. Cisco VNMC services can be restored in a few minutes. Transient data such as user sessions is not preserved in the service transfer. Existing users or service requests must be reauthenticated.

Requirements for supporting VMware HA in Cisco VNMC are as follows:

At least two hosts per HA cluster

VM and configuration files located on the shared storage and hosts are configured to access that shared storage

For additional details, see the VMware guides for HA and Fault Tolerance.