Guest

Support

System Messages and Recovery Procedures for Cisco NX-OS

  • Viewing Options

  • PDF (6.8 MB)
  • Feedback
System Messages and Recovery Procedures for Cisco NX-OS

Table Of Contents

System Messages and Recovery Procedures for Cisco NX-OS

AAA Messages

AAA-1

AAA-2

AAA-3

AAA-6

AAM Messages

AAM-2

AAM-3

ACL Messages

ACL-2

ACL-4

ACL-5

ACL-6

ACL_TCAM Messages

ACL_TCAM-2

ACL_TCAM-3

ACL_TCAM-4

ACL_TCAM-6

ACLLOG Messages

ACLLOG-4

ACLLOG-6

ACLMGR Messages

ACLMGR-2

ACLMGR-3

ACLMGR-4

ACLMGR-6

ACLQOS-SLOT# Messages

ACLQOS-SLOT#-2

ACLQOS-SLOT#-3

ACLQOS-SLOT#-4

ACLQOS-SLOT#-5

ACLTCAM Messages

ACLTCAM-2

ACLTCAM-3

ACLTCAM-4

ACLTCAM-6

AM Messages

AM-2

AM-3

AM-5

AM-6

AMM-SLOT# Messages

AMM-SLOT#-0

AMM-SLOT#-2

AMM-SLOT#-6

AMT Messages

AMT-2

AMT-3

AMT-6

ARP Messages

ARP-2

ARP-3

ARP-4

ARP-5

ASCII-CFG Messages

ASCII-CFG-2

ASCII-CFG-3

ASCII-CFG-6

ASCII_CFG Messages

ASCII_CFG-2

ASCII_CFG-6

ASSOC_MGR Messages

ASSOC_MGR-0

ASSOC_MGR-1

ASSOC_MGR-2

ASSOC_MGR-3

ASSOC_MGR-4

ASSOC_MGR-5

ASSOC_MGR-6

ASSOC_MGR-7

AVANTI_LS Messages

AVANTI_LS-0

AVANTI_LS-1

AVANTI_LS-2

AVANTI_LS-3

AVANTI_LS-4

AVANTI_LS-5

AVANTI_LS-6

AVANTI_LS-7

AVM Messages

AVM-2

AVM-3

AVM-4

AVM-5

AVM-6

BELLAGIO2 Messages

BELLAGIO2-2

BFD Messages

BFD-3

BFD-4

BFD-5

BFD-6

BFDC-SLOT# Messages

BFDC-SLOT#-2

BGP Messages

BGP-1

BGP-2

BGP-3

BGP-4

BGP-5

BIOS_DAEMON Messages

BIOS_DAEMON-2

BIOS_DAEMON-5

BIOS_DAEMON-SLOT# Messages

BIOS_DAEMON-SLOT#-2

BIOS_DAEMON-SLOT#-5

BOOTUP_TEST Messages

BOOTUP_TEST-2

BOOTVAR Messages

BOOTVAR-2

BOOTVAR-3

BOOTVAR-5

BOOTVAR-6

CALLHOME Messages

CALLHOME-2

CALLHOME-3

CALLHOME-6

CDP Messages

CDP-2

CDP-3

CDP-4

CDP-5

CDP-6

CDPD Messages

CDPD-2

CDPD-3

CDPD-4

CDPD-5

CDPD-6

CERT_EN Messages

CERT_EN-2

CERT_EN-3

CERT_EN-6

CERT_ENROLL Messages

CERT_ENROLL-2

CERT_ENROLL-3

CERT_ENROLL-6

CFS Messages

CFS-2

CFS-3

CFS-4

CFS-6

CIM Messages

CIM-2

CIM-3

CIM-6

CIMSRVPROV Messages

CIMSRVPROV-2

CIMSRVPROV-3

CIMSRVPROV-6

CLIS Messages

CLIS-5

CLK_MGR Messages

CLK_MGR-5

CLOUD Messages

CLOUD-2

CLOUD-3

CLOUD-6

CLP_XBAR Messages

CLP_XBAR-2

CLUSTER Messages

CLUSTER-2

CLUSTER-5

CLUSTER_TEST_APP Messages

CLUSTER_TEST_APP-5

CMOND Messages

CMOND-2

CMPPROXY Messages

CMPPROXY-2

CMPPROXY-5

CMPPROXY-6

CMTMDL Messages

CMTMDL-2

CMTMDL-3

COPP Messages

COPP-1

COPP-2

COPP-3

COPP-4

COPP-5

COPP-6

COPP-7

CORE-DMON Messages

CORE-DMON-2

CORE-DMON-3

CORE_DMON Messages

CORE_DMON-2

CPPA_MGR Messages

CPPA_MGR-3

CPPA_MGR-5

CRDCFG Messages

CRDCFG-2

CRDCFG-3

CRDCLIENT Messages

CRDCLIENT-2

CRDCLIENT-3

CREDITMON-SLOT# Messages

CREDITMON-SLOT#-2

CTS Messages

CTS-2

CTS-3

CTS-5

CTS-6

DC3_XBC Messages

DC3_XBC-2

DCEFIB-SLOT# Messages

DCEFIB-SLOT#-0

DCEFIB-SLOT#-2

DCEFIB-SLOT#-6

DDAS Messages

DDAS-2

DDAS-3

DDAS-6

DEBUGPROXY Messages

DEBUGPROXY-6

DEV_LOG Messages

DEV_LOG-3

DEV_LOG-SLOT# Messages

DEV_LOG-SLOT#-4

DEV_LOG_LC Messages

DEV_LOG_LC-3

DEVICE-ALIAS Messages

DEVICE-ALIAS-2

DEVICE-ALIAS-3

DEVICE-ALIAS-6

DEVICE_TEST Messages

DEVICE_TEST-2

DEVICE_TEST-3

DEVICE_TEST-4

DEVICE_TEST-5

DEVICE_TEST-6

DFTM Messages

DFTM-3

DFTM-SLOT# Messages

DFTM-SLOT#-2

DFTM-SLOT#-3

DHCP_SNOOP Messages

DHCP_SNOOP-2

DHCP_SNOOP-3

DHCP_SNOOP-4

DHCP_SNOOP-6

DIAG_PORT_LB Messages

DIAG_PORT_LB-2

DIAG_PORT_LB-3

DIAG_PORT_LB-4

DIAG_PORT_LB-5

DIAGCLIENT Messages

DIAGCLIENT-2

DIAGCLIENT-3

DIAGCLIENT-4

DIAGCLIENT-5

DIAGMGR Messages

DIAGMGR-2

DIAGMGR-3

DIAGMGR-4

DIAGMGR-5

DIAGMGR-6

DM Messages

DM-2

DM-3

DM-4

DM-5

DM-6

DM-7

DMM-SLOT# Messages

DMM-SLOT#-5

DOT1X Messages

DOT1X-2

DOT1X-3

DOT1X-4

DOT1X-5

DPP_DEBUG Messages

DPP_DEBUG-2

DPVM Messages

DPVM-2

DPVM-3

DPVM-4

DPVM-6

DRAP Messages

DRAP-2

DRAP-4

DRAP-6

DSTATS Messages

DSTATS-2

DSTATS-3

DT_HELPER Messages

DT_HELPER-2

EIGRP Messages

EIGRP-2

EIGRP-3

EIGRP-4

EIGRP-5

EIGRP-6

ELTM Messages

ELTM-2

ELTM-6

ELTMC-SLOT# Messages

ELTMC-SLOT#-2

EOU Messages

EOU-2

EOU-5

EOU-6

EOU-7

EPLD_UPGRADE Messages

EPLD_UPGRADE-2

EPP Messages

EPP-5

ETH-PORT-SEC Messages

ETH-PORT-SEC-2

ETH-PORT-SEC-3

ETH-PORT-SEC-5

ETH_PM Messages

ETH_PM-3

ETH_PM-4

ETH_PM-5

ETH_PORT_CHANNEL Messages

ETH_PORT_CHANNEL-1

ETH_PORT_CHANNEL-2

ETH_PORT_CHANNEL-3

ETH_PORT_CHANNEL-4

ETH_PORT_CHANNEL-5

ETH_PORT_CHANNEL-6

ETH_PORT_CHANNEL-7

ETH_PORT_SEC Messages

ETH_PORT_SEC-3

ETH_PORT_SEC-5

ETH_SPAN Messages

ETH_SPAN-6

ETHPORT Messages

ETHPORT-2

ETHPORT-3

ETHPORT-4

ETHPORT-5

EUREKA_USD Messages

EUREKA_USD-3

EVMC Messages

EVMC-3

EVMC-4

EVMC-5

EVMS Messages

EVMS-2

EVMS-4

EVMS-6

EX_SYSLOG Messages

EX_SYSLOG-0

EX_SYSLOG-1

EX_SYSLOG-2

EX_SYSLOG-3

EX_SYSLOG-4

EX_SYSLOG-5

EX_SYSLOG-6

EX_SYSLOG-7

EXAMPLE_TEST Messages

EXAMPLE_TEST-5

EXCEPTIONLOG-SLOT# Messages

EXCEPTIONLOG-SLOT#-2

FABRIC_START_CFG_MGR Messages

FABRIC_START_CFG_MGR-2

FBAC Messages

FBAC-5

FC-TUNNEL Messages

FC-TUNNEL-3

FC-TUNNEL-5

FC_REDIRECT Messages

FC_REDIRECT-2

FC_REDIRECT-3

FC_REDIRECT-5

FCC Messages

FCC-2

FCC-5

FCC-6

FCC_LC Messages

FCC_LC-2

FCC_LC-5

FCC_LC-6

FCD Messages

FCD-7

FCDD-SLOT# Messages

FCDD-SLOT#-3

FCDD-SLOT#-4

FCDD-SLOT#-5

FCDD-SLOT#-7

FCDDH-SLOT# Messages

FCDDH-SLOT#-3

FCDDH-SLOT#-4

FCDDH-SLOT#-5

FCDOMAIN Messages

FCDOMAIN-2

FCDOMAIN-3

FCDOMAIN-4

FCDOMAIN-5

FCDOMAIN-6

FCDOMAIN-7

FCFWD Messages

FCFWD-3

FCFWD-4

FCFWD-6

FCNPORTMUX Messages

FCNPORTMUX-2

FCNPORTMUX-3

FCNPORTMUX-4

FCNPORTMUX-5

FCNPORTMUX-6

FCNPORTMUX-7

FCNS Messages

FCNS-2

FCNS-3

FCNS-4

FCNS-6

FCOE Messages

FCOE-5

FCOE_MGR Messages

FCOE_MGR-2

FCOE_MGR-5

FCS Messages

FCS-2

FCS-3

FCS-4

FCS-5

FCS-6

FCSP-MGR Messages

FCSP-MGR-2

FCSP_MGR Messages

FCSP_MGR-2

FDMI Messages

FDMI-2

FDMI-3

FDMI-4

FDMI-6

FEATURE-MGR Messages

FEATURE-MGR-2

FEATURE_MGR Messages

FEATURE_MGR-2

FEX Messages

FEX-2

FEX-5

FICON Messages

FICON-2

FICON-3

FICON-5

FICON-6

FICONMGR Messages

FICONMGR-2

FICONMGR-3

FICONMGR-5

FICONMGR-6

FIPS Messages

FIPS-0

FIPS-6

FLASH Messages

FLASH-1

FLASH-2

FLASH-3

FLASH-5

FLASH-6

FLOGI Messages

FLOGI-1

FLOGI-2

FLOGI-4

FLOGI-5

FS Messages

FS-1

FS-2

FS-5

FS-DAEMON Messages

FS-DAEMON-2

FS-DAEMON-6

FS_DAEMON Messages

FS_DAEMON-2

FS_DAEMON-6

FSCM Messages

FSCM-2

FSPF Messages

FSPF-2

FSPF-3

FSPF-4

FSPF-5

FSPF-6

FSPF-7

FVPD Messages

FVPD-2

FVPD-3

FVPD-4

FVPD-6

FWM Messages

FWM-0

FWM-1

FWM-2

FWM-3

FWM-4

FWM-6

GAL Messages

GAL-2

GAL-6

GD Messages

GD-2

GD-3

GD-5

GD-6

GLBP Messages

GLBP-2

GLBP-3

GLBP-4

GLBP-5

HEAP Messages

HEAP-3

HSRP_ENGINE Messages

HSRP_ENGINE-3

HSRP_ENGINE-4

HSRP_ENGINE-6

ICMPV6 Messages

ICMPV6-2

ICMPV6-3

ICMPV6-6

IFMGR Messages

IFMGR-3

IFMGR-5

IGMP Messages

IGMP-2

IGMP-3

IGMP-6

IKE Messages

IKE-3

IKE-4

IKE-6

ILC-SPAN Messages

ILC-SPAN-3

ILC_HELPER Messages

ILC_HELPER-2

ILC_HELPER-3

ILC_HELPER-6

ILC_SPAN_MGR Messages

ILC_SPAN_MGR-3

IM Messages

IM-3

IM-5

IMAGE_DNLD-SLOT# Messages

IMAGE_DNLD-SLOT#-2

IMAGE_DNLD-SLOT#-4

IMAGE_DNLD-SLOT#-5

IMAGE_UPGRADE-SLOT# Messages

IMAGE_UPGRADE-SLOT#-2

IMAGE_UPGRADE-SLOT#-4

INSTALLER Messages

INSTALLER-1

INSTALLER-5

INTERFACE_VLAN Messages

INTERFACE_VLAN-4

INTERFACE_VLAN-5

IOA_LC Messages

IOA_LC-5

IOA_SUP Messages

IOA_SUP-5

IP Messages

IP-1

IP-2

IP-3

IP-4

IP-5

IP-6

IPACL Messages

IPACL-0

IPACL-1

IPACL-2

IPACL-3

IPACL-4

IPACL-5

IPACL-6

IPCONF Messages

IPCONF-2

IPCONF-3

IPCONF-6

IPFC Messages

IPFC-2

IPFC-3

IPFC-5

IPFC-6

IPPOOL Messages

IPPOOL-3

IPPOOL-5

IPQOS_MGR Messages

IPQOS_MGR-2

IPQOS_MGR-3

IPQOS_MGR-4

IPQOS_MGR-6

IPQOSMGR Messages

IPQOSMGR-2

IPQOSMGR-3

IPQOSMGR-4

IPQOSMGR-6

IPQOSMGR-SLOT# Messages

IPQOSMGR-SLOT#-3

IPS Messages

IPS-2

IPS-3

IPS-4

IPS-5

IPS-7

IPS_SB_MGR-SLOT# Messages

IPS_SB_MGR-SLOT#-2

IPS_SB_MGR-SLOT#-3

IPS_SB_MGR-SLOT#-4

IPS_SB_MGR-SLOT#-6

IPSEC Messages

IPSEC-2

IPSEC-3

IPSEC-5

IPV6 Messages

IPV6-2

IPV6-3

IPV6-4

IPV6-6

IPV6CONF Messages

IPV6CONF-2

IPV6CONF-3

IPV6CONF-6

ISAPI-SLOT# Messages

ISAPI-SLOT#-0

ISAPI-SLOT#-1

ISAPI-SLOT#-2

ISAPI-SLOT#-3

ISAPI-SLOT#-4

ISAPI-SLOT#-5

ISAPI-SLOT#-6

ISAPI-SLOT#-7

ISIS Messages

ISIS-2

ISIS-3

ISIS-4

ISIS-5

ISIS-6

ISNS Messages

ISNS-2

IVR Messages

IVR-2

IVR-3

IVR-4

IVR-5

IVR-6

IVR-7

KSINK Messages

KSINK-3

KSINK-6

L2F Messages

L2F-2

L2F-3

L2F-6

L2FM Messages

L2FM-0

L2FM-1

L2FM-2

L2FM-4

L2FM-6

L2FMC-SLOT# Messages

L2FMC-SLOT#-0

L2FMC-SLOT#-2

L2FMC-SLOT#-5

L2FMC-SLOT#-6

L2MCAST-SLOT# Messages

L2MCAST-SLOT#-0

L2MCAST-SLOT#-2

L2MCAST-SLOT#-6

L2NAC Messages

L2NAC-2

L2NAC-5

L2NAC-6

L2NAC-7

L3VM Messages

L3VM-2

L3VM-3

L3VM-4

L3VM-5

L3VM-6

LACP Messages

LACP-3

LACP-5

LC-FCFWD Messages

LC-FCFWD-3

LC-SPAN Messages

LC-SPAN-3

LC_CFG-SLOT# Messages

LC_CFG-SLOT#-2

LC_FCFWD Messages

LC_FCFWD-3

LC_PORT_CHANNEL-SLOT# Messages

LC_PORT_CHANNEL-SLOT#-0

LC_PORT_CHANNEL-SLOT#-3

LC_PORT_MGR-SLOT# Messages

LC_PORT_MGR-SLOT#-2

LC_QOS_MGR Messages

LC_QOS_MGR-3

LC_RDL Messages

LC_RDL-3

LC_RDL-6

LC_SPAN_MGR Messages

LC_SPAN_MGR-3

LCM Messages

LCM-2

LCM-3

LCM-5

LCM-6

LDAP Messages

LDAP-2

LDAP-3

LDAP-5

LDAP-6

LDP Messages

LDP-2

LDP-3

LDP-4

LIB_IFMGR Messages

LIB_IFMGR-5

LIBBASE_SVC Messages

LIBBASE_SVC-2

LIBBASE_SVC-4

LIBBASE_SVC-5

LIBGD Messages

LIBGD-2

LIBGD-3

LIBGD-5

LIBGD-6

LICMGR Messages

LICMGR-0

LICMGR-1

LICMGR-2

LICMGR-3

LICMGR-4

LICMGR-6

LISP Messages

LISP-2

LISP-3

LISP-6

LLDP Messages

LLDP-3

LLDP-5

LLDP-6

M6RIB Messages

M6RIB-2

M6RIB-3

M6RIB-5

M6RIB-6

MAC-SLOT# Messages

MAC-SLOT#-2

MCAST Messages

MCAST-2

MCAST-4

MCAST-5

MCASTFWD Messages

MCASTFWD-2

MCASTFWD-3

MCASTFWD-6

MCECM Messages

MCECM-2

MCECM-3

MCECM-4

MCECM-5

MCECM-6

MCECTEST Messages

MCECTEST-3

MCECTEST-5

MCECTEST-6

MCM Messages

MCM-2

MCM-5

MCM-6

MFDM Messages

MFDM-2

MODULE Messages

MODULE-2

MODULE-3

MODULE-4

MODULE-5

MODULE-6

MONITOR Messages

MONITOR-3

MONITOR-5

MONITOR-6

MPLS Messages

MPLS-2

MPLS-3

MPLS-6

MPLS-7

MPLS_TUNNEL Messages

MPLS_TUNNEL-3

MPLS_TUNNEL-5

MRIB Messages

MRIB-2

MRIB-3

MRIB-5

MRIB-6

MSDP Messages

MSDP-2

MSDP-3

MSDP-6

NFM Messages

NFM-2

NFM-3

NFM-4

NFM-5

NFM-6

NFM-7

NFP-SLOT# Messages

NFP-SLOT#-2

NFP-SLOT#-5

NOHMS Messages

NOHMS-2

NPC-SLOT# Messages

NPC-SLOT#-3

NPC-SLOT#-4

NPC-SLOT#-5

NPV Messages

NPV-2

NPV-3

NPV-4

NPV-5

NPV-6

NPV-7

NTP Messages

NTP-2

NTP-3

NTP-6

NVP Messages

NVP-6

NVP-SLOT# Messages

NVP-SLOT#-2

OBFL Messages

OBFL -3

OC_USD Messages

OC_USD-2

OCTOPUS Messages

OCTOPUS-2

OHMS Messages

OHMS-2

OHMS-4

OHMS-5

OHMS-6

OHMS_LC Messages

OHMS_LC-2

OHMS_LC-4

OHMS_LC-6

ORI_FWD Messages

ORI_FWD-2

ORI_FWD-6

ORI_MAC Messages

ORI_MAC-2

ORI_MAC-6

OSPF Messages

OSPF-1

OSPF-3

OSPF-4

OSPF-6

OTM Messages

OTM-2

OTM-3

OTM-5

OTM-6

PCL Messages

PCL-2

PCL-3

PCL-6

PFMA Messages

PFMA-0

PFMA-1

PFMA-2

PFMA-3

PFMA-4

PFMA-5

PFMA-7

PHY_USD-SLOT# Messages

PHY_USD-SLOT#-4

PIM Messages

PIM-2

PIM-3

PIM6 Messages

PIM6-2

PIM6-3

PIXM Messages

PIXM-2

PIXM-3

PIXM-4

PLATFORM Messages

PLATFORM-0

PLATFORM-1

PLATFORM-2

PLATFORM-3

PLATFORM-4

PLATFORM-5

PLATFORM-6

PLATFORM-7

PLOG Messages

PLOG-4

PLOG_LC Messages

PLOG_LC-4

PLOG_SUP Messages

PLOG_SUP-4

PLTFM_CONFIG Messages

PLTFM_CONFIG-4

PLUGIN Messages

PLUGIN-2

PLUGIN-3

PM Messages

PM-3

PM-4

PM-5

PMON Messages

PMON-2

PMON-3

PMON-6

POLICY_ENGINE Messages

POLICY_ENGINE-5

POLICY_ENGINE-6

PONG Messages

PONG-5

PORT Messages

PORT-2

PORT-3

PORT-4

PORT-5

PORT-CHANNEL Messages

PORT-CHANNEL-1

PORT-CHANNEL-2

PORT-CHANNEL-3

PORT-CHANNEL-4

PORT-CHANNEL-5

PORT-CHANNEL-6

PORT-CHANNEL-7

PORT-PROFILE Messages

PORT-PROFILE-2

PORT-PROFILE-3

PORT-PROFILE-6

PORT-RESOURCES Messages

PORT-RESOURCES-3

PORT-RESOURCES-5

PORT-SECURITY Messages

PORT-SECURITY-2

PORT-SECURITY-3

PORT-SECURITY-4

PORT-SECURITY-6

PORT_CHANNEL Messages

PORT_CHANNEL-1

PORT_CHANNEL-2

PORT_CHANNEL-3

PORT_CHANNEL-4

PORT_CHANNEL-5

PORT_CHANNEL-6

PORT_CHANNEL-7

PPM Messages

PPM-2

PPM-3

PPM-6

PREFPATH Messages

PREFPATH-1

PREFPATH-2

PREFPATH-3

PREFPATH-4

PREFPATH-6

PRIVATE_VLAN Messages

PRIVATE_VLAN-2

PRIVATE_VLAN-3

PRIVATE_VLAN-5

PRM Messages

PRM-3

PROC_MGR-SLOT# Messages

PROC_MGR-SLOT#-2

PROC_MGR-SLOT#-3

PROC_MGR-SLOT#-4

PROC_MGR-SLOT#-6

PSM Messages

PSM-2

PSM-3

PSM-4

PSM-6

PSS Messages

PSS-0

PSS-1

PSS-2

PSS-4

PSS-5

PTP Messages

PTP-5

PTP-6

PVLAN Messages

PVLAN-2

PVLAN-3

PVLAN-5

PWE Messages

PWE-2

PWE-3

PWE-6

QOS Messages

QOS-2

QOS-3

QOS-4

QOS-6

QOSM Messages

QOSM-2

QOSM-3

QOSM-4

QOSM-6

R2D2 Messages

R2D2-2

R2D2-6

RADIUS Messages

RADIUS-2

RADIUS-3

RADIUS-4

RADIUS-5

RADIUS-6

RDL Messages

RDL-2

RDL-3

RDL-6

RES_MGR Messages

RES_MGR-1

RES_MGR-2

RES_MGR-3

RES_MGR-4

RES_MGR-5

RES_MGR-6

RIB Messages

RIB-0

RIB-1

RIB-2

RIB-3

RIB-4

RIB-5

RIB-6

RIP Messages

RIP-2

RIP-3

RIP-4

RIP-5

RIP-6

RLIR Messages

RLIR-2

RLIR-6

RM Messages

RM-6

RM-SLOT# Messages

RM-SLOT#-2

RM-SLOT#-4

RPM Messages

RPM-2

RPM-3

RPM-6

RSCN Messages

RSCN-2

RSCN-4

RSCN-6

RSVP Messages

RSVP-2

RSVP-3

RSVP-4

RSVP-5

RSVP-6

SAC Messages

SAC-2

SAC-3

SAC-5

SAC-6

SAL Messages

SAL-5

SAN_EXT_TUNER Messages

SAN_EXT_TUNER-3

SATCTRL-SLOT# Messages

SATCTRL-SLOT#-2

SATCTRL-SLOT#-4

SATCTRL-SLOT#-5

SATMGR Messages

SATMGR-2

SATMGR-5

SCHEDULER Messages

SCHEDULER-2

SCHEDULER-3

SCHEDULER-4

SCHEDULER-6

SCSI-TARGET Messages

SCSI-TARGET-2

SCSI-TARGET-3

SCSI-TARGET-7

SCSI_FLOW_CLIENT Messages

SCSI_FLOW_CLIENT-3

SCSI_FLOW_MANAGER Messages

SCSI_FLOW_MANAGER-2

SCSI_FLOW_MANAGER-6

SCSITRGT Messages

SCSITRGT-2

SCSITRGT-3

SCSITRGT-7

SCZ Messages

SCZ-2

SCZ-3

SCZ-5

SCZ-6

SDM Messages

SDM-2

SDM-3

SDM-4

SDM-6

SDM-7

SDV Messages

SDV-2

SDV-3

SDV-4

SDV-6

SDV-7

SECURITY Messages

SECURITY-2

SECURITY-3

SECURITY-6

SECURITYD Messages

SECURITYD-2

SECURITYD-3

SECURITYD-5

SECURITYD-6

SENSOR_USD Messages

SENSOR_USD-2

SENSOR_USD-3

SENSOR_USD-5

SESSION-MGR Messages

SESSION-MGR-2

SESSION-MGR-3

SESSION-MGR-4

SFC Messages

SFC-3

SFM Messages

SFM-2

SFM-6

SKSD Messages

SKSD-3

SKSD-5

SKT_USD Messages

SKT_USD-3

SKT_USD-6

SMARTCARD Messages

SMARTCARD-3

SMARTCARD-5

SME_CPP Messages

SME_CPP-2

SME_CPP-3

SME_CPP-5

SME_CPP-SLOT# Messages

SME_CPP-SLOT#-2

SME_CPP-SLOT#-3

SME_CPP-SLOT#-4

SME_SUP Messages

SME_SUP-2

SME_SUP-3

SME_SUP-5

SMM Messages

SMM-0

SMM-2

SMM-3

SMM-5

SMM-6

SNMP Messages

SNMP-1

SNMP-2

SNMP-3

SNMP-4

SNMP-5

SNMP-6

SNMP-7

SNMPD Messages

SNMPD-1

SNMPD-2

SNMPD-3

SNMPD-4

SNMPD-5

SNMPD-6

SNMPD-7

SNSM Messages

SNSM-2

SNSM-3

SNSM-5

SPAN Messages

SPAN-2

SPAN-3

SPAN-5

SPAN-6

SPI-SLOT# Messages

SPI-SLOT#-2

SPLITTER Messages

SPLITTER-5

SSNMGR Messages

SSNMGR-2

SSNMGR-3

SSNMGR-4

STATSCLIENT Messages

STATSCLIENT-2

STATSCLIENT-3

STATSCLIENT-6

STATSINFRA Messages

STATSINFRA-3

STP Messages

STP-2

STP-3

STP-4

STP-6

SUP2_XBC Messages

SUP2_XBC-2

SUP2_XBC-3

SVC Messages

SVC-0

SVC-1

SVC-2

SVC-3

SVC-4

SVC-5

SVC-6

SVC-7

SVC_BATTERY-SLOT# Messages

SVC_BATTERY-SLOT#-2

SVC_BATTERY-SLOT#-4

SVC_BATTERY-SLOT#-6

SVI Messages

SVI-4

SVI-5

SYSMGR Messages

SYSMGR-2

SYSMGR-3

SYSMGR-4

SYSMGR-5

SYSMGR-6

SYSMGR-7

SYSTEMHEALTH Messages

SYSTEMHEALTH-2

SYSTEMHEALTH-4

SYSTEMHEALTH-5

SYSTEMHEALTH-6

TACACS Messages

TACACS-2

TACACS-3

TACACS-5

TACACS-6

TBIRD_CMN_USD Messages

TBIRD_CMN_USD-6

TBIRD_FWD_USD Messages

TBIRD_FWD_USD-6

TBIRD_MAC_USD Messages

TBIRD_MAC_USD-3

TBIRD_MAC_USD-6

TBIRD_QUE_USD Messages

TBIRD_QUE_USD-6

TBIRD_XBAR_USD Messages

TBIRD_XBAR_USD-6

TCAP Messages

TCAP-2

TE Messages

TE-2

TE-3

TE-4

TE-6

TLPM Messages

TLPM-2

TLPM-3

TLPM-4

TLPM-6

TLPORT Messages

TLPORT-2

TLPORT-3

TLPORT-4

TLPORT-6

TM Messages

TM-3

TM-4

TM-5

TM-7

TPC-SLOT# Messages

TPC-SLOT#-5

TTYD Messages

TTYD-2

TTYD-3

TTYD-6

TUNNEL Messages

TUNNEL-2

TUNNEL-3

TUNNEL-4

TUNNEL-5

TUNNEL-7

U2RIB Messages

U2RIB-2

U2RIB-3

U2RIB-5

U2RIB-6

U6RIB Messages

U6RIB-2

U6RIB-3

U6RIB-4

U6RIB-5

U6RIB-6

UDLD Messages

UDLD-3

UDLD-4

UDLD-5

UFDM Messages

UFDM-2

ULIB Messages

ULIB-2

ULIB-3

ULIB-6

ULIB-7

URIB Messages

URIB-3

URIB-4

URIB-5

URIB-6

VDC_MGR Messages

VDC_MGR-2

VDC_MGR-3

VDC_MGR-6

VEC-SLOT# Messages

VEC-SLOT#-3

VEC-SLOT#-4

VEC-SLOT#-5

VEDB_MGR Messages

VEDB_MGR-2

VEDB_MGR-6

VEDBM Messages

VEDBM-2

VEM_MGR Messages

VEM_MGR-2

VEM_MGR-3

VEM_MGR-5

VEM_MGR-6

VES-SLOT# Messages

VES-SLOT#-4

VES-SLOT#-5

VFC Messages

VFC-3

VFC-6

VIM Messages

VIM-5

VIM-SLOT# Messages

VIM-SLOT#-5

VLAN_MGR Messages

VLAN_MGR-2

VLAN_MGR-3

VLAN_MGR-4

VLAN_MGR-6

VMM Messages

VMM-2

VMS Messages

VMS-2

VMS-3

VMS-5

VNI Messages

VNI-2

VNI-3

VNI-6

VNS_AGENT Messages

VNS_AGENT-2

VNS_AGENT-3

VNS_AGENT-5

VNS_AGENT-6

VNS_AGENT-7

VNTAG_MGR Messages

VNTAG_MGR-5

VNTAGC Messages

VNTAGC-5

VPC Messages

VPC-2

VPC-3

VPC-4

VPC-5

VPC-6

VPM Messages

VPM-2

VPM-3

VPM-4

VPM-6

VPM-SLOT# Messages

VPM-SLOT#-2

VRRP-CFG Messages

VRRP-CFG-2

VRRP-CFG-3

VRRP-CFG-5

VRRP-ENG Messages

VRRP-ENG-2

VRRP-ENG-3

VRRP-ENG-4

VRRP-ENG-5

VRRP-ENG-6

VRRP_ENG Messages

VRRP_ENG-2

VRRP_ENG-3

VRRP_ENG-4

VRRP_ENG-5

VRRP_MGR Messages

VRRP_MGR-2

VRRP_MGR-3

VRRP_MGR-5

VSAN Messages

VSAN-2

VSAN-3

VSAN-6

VSD-SLOT# Messages

VSD-SLOT#-2

VSHA Messages

VSHA-3

VSHD Messages

VSHD-2

VSHD-3

VSHD-4

VSHD-5

VSHD-7

VTP Messages

VTP-0

VTP-1

VTP-2

VTP-3

VTP-4

VTP-5

VTP-6

VTP-7

WWN Messages

WWN-1

WWN-2

WWN-3

WWN-4

WWN-5

WWN-6

WWN-7

WWNM Messages

WWNM-2

WWNM-3

WWNM-4

WWNM-6

XBAR Messages

XBAR-2

XBAR-3

XBAR-5

XBAR_CLIENT Messages

XBAR_CLIENT-2

XBAR_CLIENT-3

XBAR_CLIENT-SLOT# Messages

XBAR_CLIENT-SLOT#-2

XBAR_CLIENT-SLOT#-3

XBC Messages

XBC-2

XBC-3

XBM Messages

XBM-2

XBM-3

XBM-5

XMLMA Messages

XMLMA-2

XMLMA-3

XMLMA-5

XMLMA-6

XMLSA Messages

XMLSA-2

XMLSA-5

XMLSA-6

ZBM Messages

ZBM-2

ZBM-4

ZBM-6

ZONE Messages

ZONE-2

ZONE-3

ZONE-4

ZONE-5

ZONE-6

ZS Messages

ZS-2

ZS-3

ZS-4

ZS-5

ZS-6

VEM (Nexus 1000V)


System Messages and Recovery Procedures for Cisco NX-OS


This chapter includes system messages for the Cisco NX-OS MDS 9000, Nexus 7000, Nexus 5000, Nexus 1000 families of switches, and for Cisco Virtual Security Gateway. The messages are listed in alphabetical order by the system facility that produces them. Within each system facility section, messages are listed alphabetically by severity and mnemonics. Each error message is followed by an explanation and a recommended action.

AAA Messages

This section contains the AAA messages.

AAA-1

Error Message     AAA-1-AAA_SESSION_LIMIT_REJECT: aaa request rejected as maximum aaa 
sessions are in progress 

Explanation    An AAA request has been rejected because the system has detected that the limit for the maximum concurrent AAA sessions has been exceeded.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AAA-1-SESSION_LIMIT_REJECT Format: aaa request rejected as maximum 
aaa sessions are in progress 

Explanation    aaa request rejected as the limit for maximum concurrent aaa sessions is reached.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

AAA-2

Error Message     AAA-2-AAA_NVRAM_UPGRADE_FAILURE: upgrading of accounting log failed. 
[chars] 

Explanation    The system has detected that the accounting log upgrade has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AAA-2-AAA_PROGRAM_EXIT: aaa daemon exiting: [chars] 

Explanation    The system has detected that the AAA daemon has exited.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AAA-2-NVRAM_UPGRADE_FAILURE Format: upgrading of accounting log 
failed. %s\n 

Explanation    upgrading of accounting log failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AAA-2-PROGRAM_EXIT Format: aaa daemon exiting: %s\n 

Explanation    aaa daemon is exiting.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

AAA-3

Error Message     AAA-3-AAA_NVRAMFAILURE: nvram failure 

Explanation    The system has detected that because the NVRAM cannot be read/written to, the accounting log cannot be stored in NVRAM.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AAA-3-NVRAMFAILURE Format: nvram failure 

Explanation    nvram cannot be read/written to. Hence accounting log can not be stored there.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

AAA-6

Error Message     AAA-6-AAA_ACCOUNTING_MESSAGE: [chars] 

Explanation    This message indicates that this is an accounting message.

Recommended Action    No action is required.

Error Message     AAA-6-ACCOUNTING_MESSAGE Format: %s 

Explanation    This message indicates that this is an accounting message.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

AAM Messages

This section contains the AAM messages.

AAM-2

Error Message     AAM-2-ELS_FC2_GL_SINDEX_LOOKUP_FAILED Format: Failed to lookup global 
port index for interface [%s] 

Explanation    Failed to lookup global port index for interface [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AAM-2-ELS_FC2_GL_SINDEX_LOOKUP_FAILED: Failed to lookup global port 
index for interface [[chars]] 

Explanation    Failed to lookup global port index for interface [chars].

Recommended Action    No action is required.

AAM-3

Error Message     AAM-3-ALLOC_FAILED Format: Failed in File:%s Line:%d for type %d size 
%d 

Explanation    AAM process could not allocate heap memory in File:[chars], at line:[dec], for memory-type:[dec] of Size:[dec].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AAM-3-ALLOC_FAILED: Failed in File:[chars] Line:[dec] for type [dec] 
size [dec] 

Explanation    AAM process could not allocate heap memory in File:[chars], at line:[dec], for memory-type:[dec] of Size:[dec].

Recommended Action    No action is required.

Error Message     AAM-3-ASSERTION_FAILED Format: Failed in File:%s Line:%d 

Explanation    AAM Process assertion failed in File:[chars], at line:[dec].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AAM-3-ASSERTION_FAILED: Failed in File:[chars] Line:[dec] 

Explanation    AAM Process assertion failed in File:[chars], at line:[dec].

Recommended Action    No action is required.

ACL Messages

This section contains the ACL messages.

ACL-2

Error Message     ACL-2-ACL_HA_FAILURE: Failed to do high availability operation: 
[chars]. 

Explanation    The system has failed to do a high availability operation. [chars] is the reason.

Recommended Action    No action is required.

Error Message     ACL-2-ACL_INIT_FAILED: Initialization failed for ACL: [chars], 
reason: [hex]. 

Explanation    Initialization failed for ACL due to [chars], reason: [hex].

Recommended Action    No action is required.

Error Message     ACL-2-ACL_LINECARD_STATUS: Status from linecard: [dec], for module: 
[chars](ID: [dec]), status : [dec], error_id: [hex], catastrophic: [chars], 
restart count: [dec].

Explanation    This message indicates that this message is a status from the line card [dec], for module: [chars](ID: [dec]), status : [dec], error_id: [hex], catastrophic: [chars], restart count: [dec].

Recommended Action    No action is required.

Error Message     ACL-2-ACL_MTS_FAILURE: Failed to do MTS operation: [chars]. 

Explanation    The system has failed to do an MTS operation. [chars] is the reason.

Recommended Action    No action is required.

Error Message     ACL-2-ACL_MTS_REGISTRATION_FAILED: MTS options setting to [hex] 
failed for opCode: [dec]. 

Explanation    The MTS options setting to [hex] failed for opCode: [dec].

Recommended Action    No action is required.

Error Message     ACL-2-ACL_PENDING_MSG_ARR_FULL: ACL Upgrade Pending Messages Array is 
Full with [dec] messages. Failing the MTS message with Opc: [dec], RR_TOKEN: [hex]

Explanation    This message indicates that the ACL upgrade pending messages array is full with [dec] messages. Failing the MTS message with Opc: [dec], RR_TOKEN: [hex].

Recommended Action    No action is required.

Error Message     ACL-2-ACL_PSS_FAILURE: Failed to do PSS operation: [chars], reason: 
[hex]. 

Explanation    The system has failed to do a PSS operation [chars]. [hex] is the reason.

Recommended Action    No action is required.

Error Message     ACL-2-ACL_PSS_VER_FAIL: PSS file [chars] has version 
[dec].[dec].[dec], expected version [dec].[dec].[dec]. 

Explanation    There was a mismatch in the PSS version. [chars] indicates the PSS service, [dec].[dec].[dec] its current version number and [dec].[dec].[dec] is the expected version.

Recommended Action    No action is required.

Error Message     ACL-2-ACL_RUNTIME_FAILURE: [chars] [dec], Error: [hex] 

Explanation    The system detects than an ACL runtime failure has occurred as [chars] [dec], reason: [hex].

Recommended Action    No action is required.

Error Message     ACL-2-ACL_TCAM_FAILURE: Failed to do TCAM operation: [chars]. 

Explanation    The system has failed to do a TCAM operation. [chars] is the reason.

Recommended Action    No action is required.

Error Message     ACL-2-HA_FAILURE Format: Failed to do high availability operation: %s. 

Explanation    The system has failed to do a high availability operation. [chars] is the reason.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL-2-INIT_FAILED Format: Initialization failed for ACL: %s 

Explanation    Initialization failed for ACL due to [chars], reason: [hex].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL-2-MTS_FAILURE Format: Failed to do MTS operation: %s. 

Explanation    The system has failed to do an MTS operation. [chars] is the reason.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL-2-MTS_REGISTRATION_FAILED Format: MTS options setting to %x 
failed for opCode: %d. 

Explanation    The MTS options setting to [hex] failed for opCode: [dec].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL-2-PENDING_MSG_ARR_FULL Format: ACL Upgrade Pending Messages Array 
is Full with %d messages. Failing the MTS message with Opc: %d 

Explanation    This message indicates that the ACL upgrade pending messages array is full with [dec] messages. Failing the MTS message with Opc: [dec], RR_TOKEN: [hex].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL-2-PSS_FAILURE Format: Failed to do PSS operation: %s 

Explanation    The system has failed to do a PSS operation [chars]. [hex] is the reason.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL-2-PSS_VER_FAIL Format: PSS file %s has version %d.%d.%d 

Explanation    There was a mismatch in the PSS version. [chars] indicates the PSS service, [dec].[dec].[dec] its current version number and [dec].[dec].[dec] is the expected version.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL-2-RUNTIME_FAILURE Format: %s %d 

Explanation    The system detects than an ACL runtime failure has occurred as [chars] [dec], reason: [hex].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL-2-TCAM_FAILURE Format: Failed to do TCAM operation: %s. 

Explanation    The system has failed to do a TCAM operation. [chars] is the reason.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ACL-4

Error Message     ACL-4-ACL_WARNING: [chars] [dec] 

Explanation    ACL warning messages are reported as [chars] [dec].

Recommended Action    No action is required.

Error Message     ACL-4-WARNING Format: %s %d 

Explanation    ACL warning messages are reported as [chars] [dec].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ACL-5

Error Message     ACL-5-ACL_ADJ_SHARING_STATUS: Successfully completed [chars] on 
Generation 2 linecards. 

Explanation    Successfully completed the command \[chars]\ on Generation 2 line cards.

Recommended Action    No action is required.

Error Message     ACL-5-ADJ_SHARING_STATUS Format: Successfully completed %s on 
Generation 2 linecards. 

Explanation    Successfully completed the command [chars] on Generation 2 line cards.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ACL-6

Error Message     ACL-6-ACL_DIAG_EVENT_STATUS: [chars] [hex]. 

Explanation    ACL system health management event status is reported as [chars] [hex].

Recommended Action    No action is required.

Error Message     ACL-6-ACL_E_PORT_EVENT_STATUS: [chars] [chars]. 

Explanation    ACL E port event status is reported as [chars] [chars].

Recommended Action    No action is required.

Error Message     ACL-6-ACL_FCC_EVENT_STATUS: [chars] [chars]. 

Explanation    ACL FCC event status is reported as [chars] [chars].

Recommended Action    No action is required.

Error Message     ACL-6-ACL_LINECARD_EVENT_STATUS: [chars] [hex]. 

Explanation    ACL line card event status is reported as [chars] [dec].

Recommended Action    No action is required.

Error Message     ACL-6-ACL_MCAST_EVENT_STATUS: [chars] [chars]. 

Explanation    ACL multicast event status is reported as [chars] [chars].

Recommended Action    No action is required.

Error Message     ACL-6-ACL_NX_PORT_EVENT_STATUS: [chars] [chars]. 

Explanation    ACL Nx Port event status is reported as [chars] [chars].

Recommended Action    No action is required.

Error Message     ACL-6-ACL_PORT_MODE_EVENT_STATUS: [chars] [chars]. 

Explanation    ACL portmode event status is reported as [chars] [chars].

Recommended Action    No action is required.

Error Message     ACL-6-ACL_RUNTIME_STATUS: [chars] [dec] 

Explanation    ACL runtime status is reported as [chars] [dec].

Recommended Action    No action is required.

Error Message     ACL-6-ACL_SPAN_DEST_CONFIG_STATUS: [chars] [chars]. 

Explanation    ACL SPAN destination config event status is reported as [chars] [chars].

Recommended Action    No action is required.

Error Message     ACL-6-ACL_SPAN_SRC_CONFIG_STATUS: [chars] [chars]. 

Explanation    ACL SPAN source configuration event status is reported as [chars] [chars].

Recommended Action    No action is required.

Error Message     ACL-6-ACL_STATUS: ACL Status: [chars]. 

Explanation    ACL status is reported as [chars].

Recommended Action    No action is required.

Error Message     ACL-6-ACL_UPDATE_SSRAM_QOS_EVENT_STATUS: [chars] [chars]. 

Explanation    ACL update SSRAM for QoS event status is reported as [chars] [chars].

Recommended Action    No action is required.

Error Message     ACL-6-DIAG_EVENT_STATUS Format: %s 0x%x. 

Explanation    ACL system health management event status is reported as [chars] [hex].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL-6-E_PORT_EVENT_STATUS Format: %s %s. 

Explanation    ACL E port event status is reported as [chars] [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL-6-FCC_EVENT_STATUS Format: %s %s. 

Explanation    ACL FCC event status is reported as [chars] [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL-6-LINECARD_EVENT_STATUS Format: %s %x. 

Explanation    ACL line card event status is reported as [chars] [dec].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL-6-MCAST_EVENT_STATUS Format: %s %s. 

Explanation    ACL multicast event status is reported as [chars] [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL-6-NX_PORT_EVENT_STATUS Format: %s %s. 

Explanation    ACL Nx Port event status is reported as [chars] [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL-6-PORT_MODE_EVENT_STATUS Format: %s %s. 

Explanation    ACL portmode event status is reported as [chars] [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL-6-RUNTIME_STATUS Format: %s %d 

Explanation    ACL runtime status is reported as [chars] [dec].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL-6-SPAN_DEST_CONFIG_STATUS Format: %s %s. 

Explanation    ACL SPAN destination config event status is reported as [chars] [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL-6-SPAN_SRC_CONFIG_STATUS Format: %s %s. 

Explanation    ACL SPAN source configuration event status is reported as [chars] [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL-6-STATUS Format: ACL Status: %s. 

Explanation    ACL status is reported as [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL-6-UPDATE_SSRAM_QOS_EVENT_STATUS Format: %s %s. 

Explanation    ACL update SSRAM for QoS event status is reported as [chars] [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ACL_TCAM Messages

This section contains the ACL_TCAM messages.

ACL_TCAM-2

Error Message     ACL_TCAM-2-CONFIG_READ_FROM_DRIVER_FAILED Format: %s %d 

Explanation    The system is unable to read the configuration from the forwarding engine ASIC driver. [chars] [dec], Error: 0x[hex].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL_TCAM-2-CONFIG_WRITE_TO_DRIVER_FAILED Format: %s %d 

Explanation    The system is unable to write the configuration to the forwarding engine ASIC driver. [chars] [dec], Error: 0x[hex].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL_TCAM-2-INCONSISTENT_DATABASE Format: Database found inconsistent. 

Explanation    Database found inconsistent.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL_TCAM-2-INCONSISTENT_TCAM_CONTENTS Format: TCAM contents found 
inconsistent. 

Explanation    TCAM contents are found inconsistent.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL_TCAM-2-INIT_FAILED Format: Initialization failed for forwarding 
engine ASIC: %d 

Explanation    Initialization failed for the forwarding engine ASIC [dec], in [chars] TCAM.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL_TCAM-2-INIT_REGIONS_FAILED Format: Initialization failed for 
forwarding engine ASIC: %d 

Explanation    Initialization of regions failed for the forwarding engine ASIC [dec], in [chars] TCAM, for [chars] Region.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL_TCAM-2-MTS_FAILURE Format: MTS operation failed: %s. 

Explanation    MTS operation failed. [chars] is the reason.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL_TCAM-2-MTS_REGISTRATION_FAILED Format: MTS registration failed 
for opCode: %d. 

Explanation    MTS registration failed for opCode: [dec].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL_TCAM-2-NO_TCAM_LEFT Format: ACLTCAM resource exhausted for 
interface : %s 

Explanation    ACLTCAM hardware resource is completely used.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL_TCAM-2-PSS_FAILURE Format: Failed to do PSS operation: %s 

Explanation    The system has failed to do a PSS operation [chars]. [hex] is the reason.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL_TCAM-2-PSS_OPEN_FAILED Format: PSS open failed - %x. 

Explanation    Persistent database handle could not be obtained for ACLTCAM. [hex] is the error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL_TCAM-2-RECONS_FAILED Format: Reconstruction of TCAM contents 
failed during upgrade - %x. 

Explanation    During nondisruptive upgrade, the ACLTCAM contents are not properly reconstructed. [hex] is the error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ACL_TCAM-3

Error Message     ACL_TCAM-3-REGISTER_FAILED Format: Could not register to MTS opcode 
%s - error %x. 

Explanation    ACLTCAM process could not register to the notifications mentioned by [chars]. [hex] is the error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ACL_TCAM-4

Error Message     ACL_TCAM-4-FLOW_COUNTER_INVALIDATED Format: Flow counter for flow: 
vsan: %d 

Explanation    ACLTCAM process invalidated the flow counter for flow VSAN [dec] SID [hex] DID [hex] with collected stats of [dec] frames and [dev] bytes was invalidated because of reason [%s].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACL_TCAM-4-FLOW_COUNTER_VALIDATED Format: Flow counter for flow: 
vsan: %d 

Explanation    ACLTCAM process validated the flow counter for flow VSAN [dec] SID [hex] DID [hex].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ACL_TCAM-6

Error Message     ACL_TCAM-6-STATUS Format: Status: %s. 

Explanation    ACLTCAM status is reported as: [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ACLLOG Messages

This section contains the ACLLOG messages.

ACLLOG-4

Error Message     ACLLOG-4-ACLLOG_MAXFLOW_REACHED: [chars] 

Explanation    The maximum flow has been reached in current interval: [chars].

Recommended Action    No action is required.

Error Message     ACLLOG-4-ACLLOG_THRESHOLD: [chars] 

Explanation    Threshold Reached for Flow: [chars].

Recommended Action    No action is required.

Error Message     ACLLOG-4-MAXFLOW_REACHED Format: %s 

Explanation    The maximum flow has been reached in current interval: [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLLOG-4-THRESHOLD Format: %s 

Explanation    Threshold Reached for Flow: [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ACLLOG-6

Error Message     ACLLOG-6-ACLLOG_FLOW_INTERVAL: [chars] 

Explanation    Flow informationin current alert interval: [chars].

Recommended Action    No action is required.

Error Message     ACLLOG-6-ACLLOG_NEW_FLOW: [chars] 

Explanation    New Acllog Flow: [chars].

Recommended Action    No action is required.

Error Message     ACLLOG-6-FLOW_INTERVAL Format: %s 

Explanation    Flow informationin current alert interval: [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLLOG-6-NEW_FLOW Format: %s 

Explanation    New Acllog Flow: [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ACLMGR Messages

This section contains the ACLMGR messages.

ACLMGR-2

Error Message     ACLMGR-2-ACLMGR_COMMIT_FAIL: Commit failed: client %llX, [chars] 

Explanation    The PPF commit failed.

Recommended Action    No action is required.

Error Message     ACLMGR-2-ACLMGR_DB_LOCK_MSG: ACL database message, reason: [chars], 
session 0x%llx, type: [chars] 

Explanation    ACL PPF database lock acquire/release related message.

Recommended Action    No action is required.

Error Message     ACLMGR-2-ACLMGR_NO_ERRDISABLED: [chars] event on interface [chars] 
([hex]) allowed to succeed in spite of access-list failure 

Explanation    Although an access-list operation failed during a port event, the port event still finished successfully because errordisable is disallowed.

Recommended Action    No action is required.

Error Message     ACLMGR-2-COMMIT_FAIL Format: Commit failed: client %llX 

Explanation    The PPF commit failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLMGR-2-EXITING: Exit reason: [chars] 

Explanation    The ACLMGR service process has exited due to [char]. The process has probably been restarted automatically.

Recommended Action    No action is required.

Error Message     ACLMGR-2-INITFAIL Format: ACLMGR Service Init failed: %s 

Explanation    ACLMGR Service initialization failed. [chars] explains the reason for the failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLMGR-2-INITFAIL: ACLMGR Service Init failed: [chars] 

Explanation    ACLMGR Service initialization failed. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message     ACLMGR-2-MALLOC_ERROR Format: Size %d bytes 

Explanation    The ACLMGR service could not allocate enough memory.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLMGR-2-MALLOC_ERROR: Size [dec] bytes 

Explanation    The ACLMGR service could not allocate enough memory.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLMGR-2-PSS_ERROR Format: %s: PSS ret. val=%d 

Explanation    The ACLMGR service encountered an error while operating on a persistent storage database.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLMGR-2-PSS_ERROR: [chars]: PSS ret. val=[dec] 

Explanation    The ACLMGR service encountered an error while operating on a persistent storage database.

Recommended Action    No action is required.

ACLMGR-3

Error Message     ACLMGR-3-ACLMGR_ACL_ON_FAB_INACTIVE: ACL on FEX fabric interface not 
activated 

Explanation    ACL applied to a FEX fabric port or port channel is not activated.

Recommended Action    No action is required.

Error Message     ACLMGR-3-ACLMGR_ACL_OVER_FAB_CHANNEL: ACL on FEX fabric port-channel 
bound interface not activated 

Explanation    ACL applied to a FEX interface is not activated if the interface is bound to a FEX-fabric port channel.

Recommended Action    No action is required.

Error Message     ACLMGR-3-ACLMGR_DB_LOCK_MSG: ACL database message, reason: [chars], 
session 0x%llx, type: [chars] 

Explanation    ACL PPF database lock acquire/release related message.

Recommended Action    No action is required.

Error Message     ACLMGR-3-ACLMGR_PPF_ERROR: PPF error: [chars] 

Explanation    The PPF generated an error.

Recommended Action    No action is required.

Error Message     ACLMGR-3-ACLMGR_PSS_CORRUPTED: [chars] PSS found corrupted 

Explanation    The ACLMGR service has detected a corrupted file in its persistent information databases The database would be recreated.

Recommended Action    No action is required.

Error Message     ACLMGR-3-ACLMGR_STAT_CONSOLIDATION_FAILURE: ACL statistic parsing or 
consolidation failed 

Explanation    A statistic update failed during the parsing or consolidation step; statistics may have been lost.

Recommended Action    No action is required.

Error Message     ACLMGR-3-ACLMGR_VACL_REDIRECTION_DISABLED_REMOVAL: VACL redirection 
to interface [chars] ([hex]) disabled: the port has been removed 

Explanation    A VACL redirection to the port has been deactivated because the port has been removed.

Recommended Action    No action is required.

Error Message     ACLMGR-3-ACLMGR_VERIFY_FAIL: Verify failed: client %llX, [chars] 

Explanation    The PPF Verify failed.

Recommended Action    No action is required.

Error Message     ACLMGR-3-DB_LOCK_MSG Format: ACL database message 

Explanation    ACL PPF database lock acquire/release related message.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLMGR-3-MTSERROR Format: %s 

Explanation    ACLMGR Service encountered an MTS error. [chars] specifies the context where the error occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLMGR-3-MTSERROR: [chars] 

Explanation    ACLMGR Service encountered an MTS error. [chars] specifies the context where the error occurred.

Recommended Action    No action is required.

Error Message     ACLMGR-3-PPF_ERROR Format: PPF error: %s 

Explanation    The PPF generated an error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLMGR-3-STAT_CONSOLIDATION_FAILURE Format: ACL statistic parsing or 
consolidation failed 

Explanation    A statistic update failed during the parsing or consolidation step; statistics may have been lost.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLMGR-3-VERIFY_FAIL Format: Verify failed: client %llX 

Explanation    The PPF Verify failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ACLMGR-4

Error Message     ACLMGR-4-ACLMGR_PPF_WARNING: PPF warning: [chars] 

Explanation    The PPF generated warning.

Recommended Action    No action is required.

Error Message     ACLMGR-4-ACLMGR_VACL_REDIRECTION_DISABLED_PCM: VACL redirection to 
interface [chars] ([hex]) disabled: the port became a portchannel member 

Explanation    A VACL redirection to the port has been temporarily deactivated because it is now a member in a port channel.

Recommended Action    No action is required.

Error Message     ACLMGR-4-PPF_WARNING Format: PPF warning: %s 

Explanation    The PPF generated warning.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLMGR-4-PSS_VERSION_MISMATCH Format: PSS %d Code %d 

Explanation    There was a version mismatch between the ACLMGR service and one of its persistent storage databases. The persistent information has been translated to the new format.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLMGR-4-PSS_VERSION_MISMATCH: PSS [dec] Code [dec] 

Explanation    There was a version mismatch between the ACLMGR service and one of its persistent storage databases. The persistent information has been translated to the new format.

Recommended Action    No action is required.

ACLMGR-6

Error Message     ACLMGR-6-ACLMGR_PPF_NOTIF: PPF notification: [chars] 

Explanation    The PPF generated a notification.

Recommended Action    No action is required.

Error Message     ACLMGR-6-BECAME_ACTIVE Format: Became ACTIVE from standby mode 

Explanation    The ACLMGR service on the standby supervisor became active and it is ready to serve client requests.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLMGR-6-BECAME_ACTIVE: Became ACTIVE from standby mode 

Explanation    The ACLMGR service on the standby supervisor became active and it is ready to serve client requests.

Recommended Action    No action is required.

Error Message     ACLMGR-6-BECAME_STDBY Format: Became STANDBY from active mode 

Explanation    The ACLMGR service became standby from active mode.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLMGR-6-BECAME_STDBY: Became STANDBY from active mode 

Explanation    The ACLMGR service became standby from active mode.

Recommended Action    No action is required.

Error Message     ACLMGR-6-FAILED_TO_SEND_HEARTBEAT Format: Failed to send heartbeat to 
system manager: Reason=%s 

Explanation    The ACLMGR service was unable to send heartbeats to the system manager.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLMGR-6-FAILED_TO_SEND_HEARTBEAT: Failed to send heartbeat to system 
manager: Reason=[chars] 

Explanation    The ACLMGR service was unable to send heartbeats to the system manager.

Recommended Action    No action is required.

Error Message     ACLMGR-6-PPF_NOTIF Format: PPF notification: %s 

Explanation    The PPF generated a notification.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLMGR-6-SERVICE_UP: Initialized [chars] 

Explanation    The ACLMGR service is up and ready The service was initialized in [char] mode.

Recommended Action    No action is required.

Error Message     ACLMGR-6-SRVEXIT Format: ACLMGR Service shutting down gracefully 

Explanation    ACLMGR Service is shutting down gracefully.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLMGR-6-SRVEXIT: ACLMGR Service shutting down gracefully 

Explanation    ACLMGR Service is shutting down gracefully.

Recommended Action    No action is required.

Error Message     ACLMGR-6-SWITCHOVER Format: Switching Over to other Sup. 

Explanation    The ACLMGR service has successfully switched over to the standby supervisor module.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLMGR-6-SWITCHOVER: Switching Over to other Sup. 

Explanation    The ACLMGR service has successfully switched over to the standby supervisor module.

Recommended Action    No action is required.

ACLQOS-SLOT# Messages

This section contains the ACLQOS-SLOT# messages.

ACLQOS-SLOT#-2

Error Message     ACLQOS-SLOT#-2-ACLQOS_FAILED: ACLQOS failure: [chars] 

Explanation    ACLQOS operation failed in the aclqos client.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLQOS-SLOT#-2-ACLQOS_INBAND_INTERFACE_FAILURE: Inband interface lif 
lookup failed ([chars]) 

Explanation    Inband interface lif lookup failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLQOS-SLOT#-2-ACLQOS_MALLOC_FAILED: Memory allocation failed. 
[chars] 

Explanation    Memory allocation failed. This is a critical failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLQOS-SLOT#-2-ACLQOS_OOTR: Tcam resource exhausted: [chars] 

Explanation    TCAM resources to program acls exhausted.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLQOS-SLOT#-2-PPF_FAILED: Database failure: [chars] 

Explanation    Database operation failed in the aclqos client.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ACLQOS-SLOT#-3

Error Message     ACLQOS-SLOT#-3-ACLQOS_CC_INVALID: Invalid Congestion Control 
parameters 

Explanation    Invalid Congestion Control parameters.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLQOS-SLOT#-3-ACLQOS_CC_INVALID: Invalid Congestion Control 
parameters: [chars] 

Explanation    Invalid Congestion Control parameters.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLQOS-SLOT#-3-ACLQOS_MCM_ERROR: MCM Message Inconsistent. Please 
collect MCM and ACLMgr Tech Support for all VDCs

Explanation    MCM Message Inconsistent.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLQOS-SLOT#-3-ACLQOS_PAUSE_INVALID: Invalid Pause parameters 

Explanation    Invalid Pause parameters.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLQOS-SLOT#-3-ACLQOS_PAUSE_INVALID: Invalid Pause parameters: 
[chars] 

Explanation    Invalid Pause parameters.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLQOS-SLOT#-3-ACLQOS_QUEUING_ERROR: ACL/QoS queuing error: [chars] 

Explanation    Internal error in ACL/QoS queing configuration.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ACLQOS-SLOT#-4

Error Message     ACLQOS-SLOT#-4-ACLQOS_ATOMIC_ERR: [chars] 

Explanation    TCAM will be overused, turn off atomic update.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLQOS-SLOT#-4-ACLQOS_MATCH_ALL_MERGE_UPDATE: Warning (match_all 
merging): [chars] 

Explanation    Warning (match_all merging).

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLQOS-SLOT#-4-ACLQOS_OVER_THRESHOLD: Tcam [dec] Bank [dec]'s usage 
has reached its threshold 

Explanation    TCAM is almost full.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLQOS-SLOT#-4-ACLQOS_QUEUING_COS2Q_INVALID: ACL/QoS invalid queuing 
policy because of cos map change: [chars] queue [chars], interface [chars] 

Explanation    Attemped to configure an invalid queuing policy.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLQOS-SLOT#-4-ACLQOS_QUEUING_INVALID: ACL/QoS invalid queuing 
policy: [chars] 

Explanation    Attemped to configure an invalid queuing policy.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLQOS-SLOT#-4-ACLQOS_UNDER_THRESHOLD: Tcam [dec] Bank [dec]'s usage 
is below the threshold now 

Explanation    TCAM's usage is below the threshold.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLQOS-SLOT#-4-ACLQOS_WARNING: ACLQOS Warning: [chars] 

Explanation    ACLQOS Warnings.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ACLQOS-SLOT#-5

Error Message     ACLQOS-SLOT#-5-ACLQOS_DISRUPTIVE_IPv6_UPDATE: Disruptive update of 
IPv6 compression entries 

Explanation    Disruptive IPv6 compression entries update.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ACLQOS-SLOT#-5-ACLQOS_NON_ATOMIC: Non atomic ACL/QoS policy update 
done for [chars] 

Explanation    Nonatomic ACL/QoS policy update was done.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ACLTCAM Messages

This section contains the ACLTCAM messages.

ACLTCAM-2

Error Message     ACLTCAM-2-ACL_TCAM_ADJ_EXHAUSTED: ACLTCAM failed to program route for 
VSAN: [dec], SID: [chars] DID: [chars], error: [chars].

Explanation    ACLTCAM process experienced a failure while programming route for VSAN [dec] SID [chars] DID [chars] due to resource exhaustion. [chars] is the error code.

Recommended Action    No action is required.

Error Message     ACLTCAM-2-ACL_TCAM_ALMOST_FULL: TCAM close to FULL. [chars] TCAM 
Usage ([dec]/[dec]) exceeded [dec]% fwd-eng: [dec], [chars]

Explanation    [chars] TCAM usage [dec]/[dec] exceeded [dec] percent on fwd-engine [dec], [chars].

Recommended Action    No action is required.

Error Message     ACLTCAM-2-ACL_TCAM_CONFIG_READ_FROM_DRIVER_FAILED: [chars] [dec], 
Error: [hex]. 

Explanation    The system is unable to read the configuration from the forwarding engine ASIC driver. [chars] [dec], Error: 0x[hex].

Recommended Action    No action is required.

Error Message     ACLTCAM-2-ACL_TCAM_CONFIG_WRITE_TO_DRIVER_FAILED: [chars] [dec], 
Error: [hex]. 

Explanation    The system is unable to write the configuration to the forwarding engine ASIC driver. [chars] [dec], Error: 0x[hex].

Recommended Action    No action is required.

Error Message     ACLTCAM-2-ACL_TCAM_FLOW_STATS_READ_FAILED: Hardware flow stats read 
failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec], Error: 
[chars]).

Explanation    Hardware flow stats read failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec] Error: [chars]).

Recommended Action    No action is required.

Error Message     ACLTCAM-2-ACL_TCAM_INCONSISTENT_DATABASE: Database found 
inconsistent. 

Explanation    Database found inconsistent.

Recommended Action    No action is required.

Error Message     ACLTCAM-2-ACL_TCAM_INCONSISTENT_TCAM_CONTENTS: TCAM contents found 
inconsistent. 

Explanation    TCAM contents are found inconsistent.

Recommended Action    No action is required.

Error Message     ACLTCAM-2-ACL_TCAM_INIT_FAILED: Initialization failed for forwarding 
engine ASIC: [dec], [chars] TCAM. 

Explanation    Initialization failed for the forwarding engine ASIC [dec], in [chars] TCAM.

Recommended Action    No action is required.

Error Message     ACLTCAM-2-ACL_TCAM_INIT_REGIONS_FAILED: Initialization failed for 
forwarding engine ASIC: [dec], [chars] TCAM, [chars] Region. 

Explanation    Initialization of regions failed for the forwarding engine ASIC [dec], in [chars] TCAM, for [chars] Region.

Recommended Action    No action is required.

Error Message     ACLTCAM-2-ACL_TCAM_MALLOC_FAILURE: Memory allocation failed for size 
[dec]. 

Explanation    Memory allocation is failed for size [dec] bytes.

Recommended Action    Restart the process.

Error Message     ACLTCAM-2-ACL_TCAM_MTS_FAILURE: MTS operation failed: [chars]. 

Explanation    MTS operation failed. [chars] is the reason.

Recommended Action    No action is required.

Error Message     ACLTCAM-2-ACL_TCAM_MTS_REGISTRATION_FAILED: MTS registration failed 
for opCode: [dec]. 

Explanation    MTS registration failed for opCode: [dec].

Recommended Action    No action is required.

Error Message     ACLTCAM-2-ACL_TCAM_NO_ROUTE: ACLTCAM failed to get route for VSAN: 
[dec], Rewrite: [chars] DID: [chars] DID MASK: [chars], error: [hex].

Explanation    ACLTCAM process experienced a failure while getting route for VSAN [dec] Rewrite [chars] DID [chars] DID Mask [chars]. [hex] is the error code.

Recommended Action    No action is required.

Error Message     ACLTCAM-2-ACL_TCAM_NO_TCAM_LEFT: ACLTCAM resource exhausted for 
interface : [chars] 

Explanation    ACLTCAM hardware resource is completely used.

Recommended Action    No action is required.

Error Message     ACLTCAM-2-ACL_TCAM_PHY_TCAM_READ_FAILED: [chars] read from hardware 
TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec], Error: 
[chars]).

Explanation    [chars] read from hardware TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec] Error: [chars]).

Recommended Action    No action is required.

Error Message     ACLTCAM-2-ACL_TCAM_PHY_TCAM_READ_INVALID: Invalid([chars], value: 
[dec]) TCAM entry read from hardware TCAM (FWD-Engine: [dec], [chars] TCAM, 
Address: [dec]), Ignoring this entry.

Explanation    Invalid([chars], value: [dec]) TCAM entry from hardware TCAM(FWD-Engine: [dec], [chars] TCAM, Address: [dec]) Ignoring this entry.

Recommended Action    No action is required.

Error Message     ACLTCAM-2-ACL_TCAM_PHY_TCAM_WRITE_FAILED: [chars] write to hardware 
TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec], Error: 
[chars]).

Explanation    [chars] write to hardware TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec] Error: [chars]).

Recommended Action    No action is required.

Error Message     ACLTCAM-2-ACL_TCAM_PSS_FAILURE: Failed to do PSS operation: [chars], 
reason: [hex]. 

Explanation    The system has failed to do a PSS operation [chars]. [hex] is the reason.

Recommended Action    No action is required.

Error Message     ACLTCAM-2-PSS_OPEN_FAILED: PSS open failed - [hex]. 

Explanation    Persistent database handle could not be obtained for ACLTCAM. [hex] is the error.

Recommended Action    No action is required.

Error Message     ACLTCAM-2-RECONS_FAILED: Reconstruction of TCAM contents failed 
during upgrade - [hex]. 

Explanation    During nondisruptive upgrade, the ACLTCAM contents are not properly reconstructed. [hex] is the error.

Recommended Action    No action is required.

ACLTCAM-3

Error Message     ACLTCAM-3-REGISTER_FAILED: Could not register to MTS opcode [chars] 
- error [hex]. 

Explanation    ACLTCAM process could not register to the notifications mentioned by [chars]. [hex] is the error.

Recommended Action    No action is required.

ACLTCAM-4

Error Message     ACLTCAM-4-ACL_TCAM_BELOW_THRESHOLD: [chars] TCAM usage ([dec]/[dec]) 
fell below [dec]% fwd-eng: [dec], [chars]

Explanation    [chars] TCAM usage [dec]/[dec] fell below [dec] percent on fwd-engine [dec], [chars].

Recommended Action    No action is required.

Error Message     ACLTCAM-4-ACL_TCAM_BEYOND_THRESHOLD: [chars] TCAM usage ([dec]/[dec]) 
exceeded [dec]% fwd-eng: [dec], [chars]

Explanation    [chars] TCAM usage [dec]/[dec] exceeded [dec] percent on fwd-engine [dec], [chars].

Recommended Action    No action is required.

Error Message     ACLTCAM-4-ACL_TCAM_FLOW_COUNTER_INVALIDATED: Flow counter for flow: 
vsan: [dec], sid: [hex], did: [hex] with statistics: frames = %llu & bytes = %llu 
was invalidated due to: [chars]

Explanation    ACLTCAM process invalidated the flow counter for flow VSAN [dec] SID [hex] DID [hex] with collected stats of [dec] frames and [dev] bytes was invalidated because of reason [[chars]].

Recommended Action    No action is required.

Error Message     ACLTCAM-4-ACL_TCAM_FLOW_COUNTER_VALIDATED: Flow counter for flow: 
vsan: [dec], sid: [hex], did: [hex] is now valid

Explanation    ACLTCAM process validated the flow counter for flow VSAN [dec] SID [hex] DID [hex].

Recommended Action    No action is required.

ACLTCAM-6

Error Message     ACLTCAM-6-ACL_TCAM_STATUS: Status: [chars]. 

Explanation    ACLTCAM status is reported as: [chars].

Recommended Action    No action is required.

AM Messages

This section contains the AM messages.

AM-2

Error Message     AM-2-API_INIT Format: Failed to initialize %s API 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-BAD_TIMER Format: %s 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-CLI_INIT Format: Failed to initialize CLI 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-INIT_FAIL Format: Initialization failure 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-MQ_OPEN Format: Failed to open message queue %s: %s 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-MTS_BIND Format: Failed to do mts_bind for %s: %s 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-MTS_OPC_SET Format: Failed to register with opcode %d: %s 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-MTS_RECV Format: MTS queue receive failed on %s queue: %s 

Explanation    An unexpected fatal error has occurred.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-MTS_SADDR_GET Format: Failed to get source of mts queue %s: %s 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-NO_WORKBIT Format: Failed to register %s too many notify clients 

Explanation    An unexpected fatal error has occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AM-2-REQD_COMP_DOWN Format: Required component \%s\ has gone down. 

Explanation    An unexpected fatal error has occurred.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-REQD_COMP_FAIL Format: Required component \%s\ has failed to 
initialize. 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-SDB_CREAT Format: Failed to create shared database 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-SDB_DESTROY Format: Failed to destroy shared database 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-SDB_OPEN Format: Failed to open shared database 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-SET_SCHED Format: Failed to set policy or priority 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-SHM_CREAT Format: Failed to create shared memory: %s 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-SHM_LOCK_CREAT Format: Failed to create shared memory lock: %s 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-SVR_REG Format: Failed to register as a client of %s for VRF %s 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-SYSMGR_NAME Format: Failed to get name from sysmgr during %s 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-SYSMGR_NOTIFY Format: Bad notification from sysmgr for %s 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-SYSMGR_QUERY Format: Failed to query sysmgr for %s 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-SYSMGR_UUID Format: Failed to get uuid from sysmgr during %s 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-THR_CREAT Format: Failed to create thread %s: error %d 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-THREAD_FAIL Format: Failed to start %s thread 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-2-URIB_PIB Format: Unable to get pib for %s VRF from URIB 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

AM-3

Error Message     AM-3-BAD_PARAMS Format: Called %s with address family %d, iod %d, 
l3address %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-3-DEL_PROT_ADJ Format: Unable to delete protocol adjacency for %s, 
uuid %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-3-IF_INDEX Format: Invalid interface index received from %d 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-3-IP_GLEAN_EXCESS_TRAFFIC Format: Excess traffic (%llu packets / 
%llu octets) were dropped in %s seconds for ungleaned prefix %s/32 on interface 
%s in vrf %s 

Explanation    This message indicates an informational log about a system event.

Recommended Action    No action is required.

Error Message     AM-3-MAC_REG_FAILED Format: Mac registration with L2FM failed for mac 
%s, iod %s, phy iod: %s 

Explanation    MAC registration with L2FM failed.

Recommended Action    No action is required.

Error Message     AM-3-MAX_RETRIES Format: Notification retry limit exceeded for %s 

Explanation    Client is not replying to our notifications.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AM-3-MQ_RECV Format: Message queue receive failed on %s queue: %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-3-MQ_SEND Format: Failed to send %s to %s queue: %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-3-MSG_TO_TLV Format: Notification message to TLV failed 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-3-MTS_DROP Format: MTS drop failed on %s queue: %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-3-MTS_SEND Format: Failed to send %s to %s queue: %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-3-NO_AF Format: %s: Unable to get address family block for index %d 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-3-NO_MEM Format: Malloc failed for %s %s 

Explanation    The system may be low on memory.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AM-3-NO_PIB Format: Unable to get pib for client pid %d while 
processing %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-3-NO_SMEM Format: Smalloc failed for %s %s 

Explanation    AM's shared memory quota may be used up, due to a large number of adjacencies or a memory leak.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AM-3-PT_ADD Format: Pt_add failed for %s %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-3-QUEUE Format: %s failed for %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-3-READ_LOCK_HOLD Format: %s:%s():%d: Assert, read-lock not 
acquired 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-3-RIB_RTE_CHG Format: Failed to send AM route changes to %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-3-THR_MUTEX_LOCK Format: Failed to thread mutex lock 

Explanation    Failed function pthread_mutex_lock.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-3-THR_MUTEX_UNLOCK Format: Failed to thread mutex lock 

Explanation    Failed function pthread_mutex_unlock.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     AM-3-TLV_TO_STRUCT Format: Notification TLV to struct failed 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-3-URIB_CNTXT Format: Failed to get %s VRF from URIB 

Explanation    An unrecoverable software error has occurred during the AM initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

AM-5

Error Message     AM-5-INVALID_NOTIFY Format: Received invalid notification message 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-5-MQ_MAJOR Format: Received unknown major message type (%d) from %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-5-MQ_MINOR Format: Received unknown minor message type (%d) from %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-5-MQ_UNEXP Format: Received unexpected message (%d/%d) on %s queue 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-5-MSG_UNK Format: Received unknown % type: %lu 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-5-MTS_OPC_UNK Format: Received unknown MTS opcode %lu 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     AM-5-REG_DELAY Format: AM register %s delay: %d seconds 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

AM-6

Error Message     AM-6-FAILED_STATS Format: Failed to retrieve stats from FTM 

Explanation    This message indicates an informational log about a system event.

Recommended Action    No action is required.

Error Message     AM-6-SYSMAN_CLEANUP Format: Terminated by SYSMAN cleanup signal ; 
Explanation: Informational log about a system event. 

Explanation    The system has detected an error.

Recommended Action    No action is required.

AMM-SLOT# Messages

This section contains the AMM-SLOT# messages.

AMM-SLOT#-0

Error Message     AMM-SLOT#-0-CLI_INIT_FAILED: CLI library initialization failed! 

Explanation    AMM failed to initialize CLI infrastructure\sbackendlibrary.Thisisafatalerror.'

Recommended Action    No action is required.

Error Message     AMM-SLOT#-0-TIMER_INIT_FAILED: Timer subsystem initialization failed! 

Explanation    AMM failed to initialize timer library. This is a fatal error.

Recommended Action    No action is required.

AMM-SLOT#-2

Error Message     AMM-SLOT#-2-AMM_MEM_ALLOC: Memory allocation failed. [chars] 

Explanation    Memory allocation failed. This is a critical failure.

Recommended Action    No action is required.

Error Message     AMM-SLOT#-2-AMM_RECOVERY_ERROR: Error in Recovery: [chars] 

Explanation    AMM failed to recover after a re-start. This is a fatal error.

Recommended Action    No action is required.

AMM-SLOT#-6

Error Message     AMM-SLOT#-6-INITIALIZED: Internal state created [chars] 

Explanation    AMM has created its internal state stateless/stateful [chars].

Recommended Action    No action is required.

AMT Messages

This section contains the AMT messages.

AMT-2

Error Message     AMT-2-SHM_LOCK_CREAT Format: Failed to create shared memory lock: %s 

Explanation    The system has failed to initialize.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

AMT-3

Error Message     AMT-3-AMT_INIT Format: AMT init failed: %s 

Explanation    AMT process initialization failed.

Recommended Action    Dump core, and then restart component.

Error Message     AMT-3-API_INIT Format: Couldn't initialize %s API 

Explanation    AMT failed to open API to interact with the component.

Recommended Action    No action is required.

Error Message     AMT-3-BIND Format: bind() on %s failed: %s 

Explanation    AMT failed to bind UDP socket.

Recommended Action    Dump core, and then restart component.

Error Message     AMT-3-COMP_DEREG Format: Unable to de-register with %s 

Explanation    AMT failed to de-register with a server component.

Recommended Action    No action is required.

Error Message     AMT-3-COMP_REG Format: Unable to register with %s 

Explanation    AMT failed to register with a server component.

Recommended Action    Dump core, and then restart component.

Error Message     AMT-3-DISC_NOT_ANYCAST Format: Relay Discovery packet from %s is 
addressed to %s, not an anycast address 

Explanation    An AMT Gateway sent Relay Discovery not using the Relay Anycast address.

Recommended Action    Configure the network or router to decrease the number of routes.

Error Message     AMT-3-IP_TUNNEL_LIMIT Format: Reach IP tunnel limit of %d 

Explanation    AMT process failed to create tunnel because the policy limit has been reached.

Recommended Action    Configure the network or router to decrease the number of routes.

Error Message     AMT-3-IPV6_TUNNEL_LIMIT Format: Reach IPv6 tunnel limit of %d 

Explanation    AMT process failed to create tunnel because the policy limit has been reached.

Recommended Action    Configure the network or router to decrease the number of routes.

Error Message     AMT-3-LIB_API_INIT Format: Couldn't initialize %s API 

Explanation    Failed to open AMT API to interact with the component.

Recommended Action    No action is required.

Error Message     AMT-3-LIB_SM_OPEN Format: Couldn't open shm segment %s 

Explanation    Process failed to access AMT's shared memory.

Recommended Action    Dump core, and then restart component.

Error Message     AMT-3-MALLOC Format: Private mem malloc (%lu) failed in %s 

Explanation    AMT process is out of free private memory.

Recommended Action    Configure the network or router to decrease the number of routes.

Error Message     AMT-3-MRIB_ADD_ROUTE Format: MRIB add route failed in %s 

Explanation    AMT failed to add route in MRIB.

Recommended Action    No action is required.

Error Message     AMT-3-MRIB_DEL_ROUTE Format: MRIB delete route failed in %s 

Explanation    AMT failed to delete route in MRIB.

Recommended Action    No action is required.

Error Message     AMT-3-MTS_DROP Format: Error returned from mts_drop(), errno: %s 

Explanation    AMT called an MTS API which returned an error.

Recommended Action    Dump core, and then restart component.

Error Message     AMT-3-MTS_RECV Format: Error returned from mts_recv(), errno: %s 

Explanation    AMT called an MTS API which returned an error.

Recommended Action    Dump core, and then restart component.

Error Message     AMT-3-NO_AMT_PAYLOAD Format: No AMT payload after stripping IP/IPv6 
and UDP headers from %s, length: %d 

Explanation    AMT process received packet which is too short. The other side of the AMT tunnel has a protocol error.

Recommended Action    Configure the network or router to decrease the number of routes.

Error Message     AMT-3-NO_M_COPYBACK Format: m_copyack() failed in 
amt_receive_multicast_data() 

Explanation    AMT process failed to copy AMT multicast data into an mbuf for IP to replicate the packet.

Recommended Action    No action is required.

Error Message     AMT-3-NO_M_GET Format: amt_receive_multicast_data() could allocate 
mbuf data structure 

Explanation    AMT process failed to allocate an mbuf data structure to forward AMT encapsulated data in an AMT Gateway.

Recommended Action    No action is required.

Error Message     AMT-3-NO_SET_PRIORITY Format: Failed to set policy or priority 

Explanation    AMT process could not set itself process priority, exiting.

Recommended Action    No action is required.

Error Message     AMT-3-PKT_BAD_NONCE Format: Nonce from Relay Advertisement packet 
from %s does not match Relay Discovery packet nonce, received 0x%08x, expected 
0x%08x 

Explanation    There is a possible AMT spoof attack since the Advertise and Disocvery nonces do not match.

Recommended Action    Configure the network or router to decrease the number of routes.

Error Message     AMT-3-PKT_TOO_SHORT Format: Packet too short from %s 

Explanation    AMT process received packet which is too short. The other side of the AMT tunnel has a protocol error.

Recommended Action    Configure the network or router to decrease the number of routes.

Error Message     AMT-3-PT_ADD Format: Couldn't add %s to Patricia Trie 

Explanation    AMT failed to update the tunnel Patricia Trie.

Recommended Action    No action is required.

Error Message     AMT-3-PT_DEL Format: Couldn't delete %s from local PT 

Explanation    AMT failed to delete the local route-table entry.

Recommended Action    No action is required.

Error Message     AMT-3-PTHREAD_CREATE Format: Couldn't create thread %s 

Explanation    AMT process failed to create a task thread.

Recommended Action    Dump core, and then restart component.

Error Message     AMT-3-RESTART_REASON Format: AMT process has restarted, restart 
reason: %s\n 

Explanation    AMT is restoring the routes it had added in previous instance.

Recommended Action    No action is required.

Error Message     AMT-3-RLIMIT Format: Couldn't set AMT data segment size to %lu 

Explanation    AMT process could not set a memory resource limit, exiting.

Recommended Action    No action is required.

Error Message     AMT-3-SETSOCKOPT Format: setsockopt() on %s failed: %s 

Explanation    AMT failed in UDP socket operation.

Recommended Action    Dump core, and then restart component.

Error Message     AMT-3-SLAB_CREATE Format: Slab alloc of type %s failed 

Explanation    AMT process failed to allocate Slab memory.

Recommended Action    Configure the network or router to decrease the number of routes.

Error Message     AMT-3-SM_CREATE Format: Couldn't create shm segment %s 

Explanation    AMT process failed to initialize shared memory resource.

Recommended Action    Dump core, and then restart component.

Error Message     AMT-3-SMALLOC Format: Shared mem malloc (%lu) failed in %s 

Explanation    AMT process is out of free shared memory.

Recommended Action    Configure the network or router to decrease the number of routes.

Error Message     AMT-3-SOCKET Format: socket() for %s failed: %s 

Explanation    AMT failed to obtain UDP socket.

Recommended Action    Dump core, and then restart component.

Error Message     AMT-3-TIMER_SET_INIT Format: Couldn't init %s active timer set 

Explanation    AMT failed to initialize timer resource.

Recommended Action    Dump core, and then restart component.

Error Message     AMT-3-TUNNEL_FAILED Format: Could not allocate shared-memory for 
amt_tunneltype data structure 

Explanation    AMT process failed to create data structure to establish tunnel.

Recommended Action    Configure the network or router to decrease the number of routes.

Error Message     AMT-3-UDP_SENDTO Format: udp_sendto() failed to %s in %s, error: %s 

Explanation    AMT failed to send over UDP socket.

Recommended Action    No action is required.

Error Message     AMT-3-UNKNOWN_MTYPE Format: Unknown mtype: %d/%d in %s 

Explanation    AMT process received unknown Interprocess message, dropped.

Recommended Action    No action is required.

AMT-6

Error Message     AMT-6-RESTART_SHUTDOWN Format: AMT shutting self down via restart 
command 

Explanation    AMT process is shutting itself down due to the restart command.

Recommended Action    No action is required.

Error Message     AMT-6-SHUTDOWN Format: Shutting down AMT process 

Explanation    PIM received a shutdown request.

Recommended Action    No action is required.

Error Message     AMT-6-SHUTDOWN_SELF Format: AMT shutting self down 

Explanation    AMT process is shutting itself down.

Recommended Action    No action is required.

Error Message     AMT-6-UNKNOWN_OPC Format: Received unknown mts opcode %d 

Explanation    AMT process received unknown Interprocess message, dropped.

Recommended Action    No action is required.

ARP Messages

This section contains the ARP messages.

ARP-2

Error Message     ARP-2-AM_PIB Format: Failed to acquire AM handle %s 

Explanation    An unrecoverable software error has occurred during ARP initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-AM_REG Format: Failed to register as a client of AM %s 

Explanation    An unrecoverable software error has occurred during ARP initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-API_INIT Format: Failed to initialize %s API 

Explanation    An unrecoverable software error has occurred during ARP initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-API_INITIALIZE Format: Failed to initialize %s API with rc=0x%x, 
%s 

Explanation    An unrecoverable software error has occurred during ARP initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-CLI_INIT Format: Failed to initialize CLI 

Explanation    An unrecoverable software error has occurred during ARP initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-DUP_SRC_IP Format: Source address of packet received from %s on 
%s(%s) is duplicate of local, %s 

Explanation    There may be another router on this network that is configured with the same IP address.

Recommended Action    Check all routers on the interface for a misconfiguration.

Error Message     ARP-2-DUP_SRCIP Format: Source address of packet received from %s on 
%s is duplicate of local, %s 

Explanation    There may be another router on this network that is configured with the same IP address.

Recommended Action    Check all routers on the interface for a misconfiguration.

Error Message     ARP-2-INIT_FAIL Format: Initialization failure 

Explanation    An unrecoverable software error has occurred during ARP initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-MQ_OPEN Format: Failed to open message queue %s: %s 

Explanation    An unrecoverable software error has occurred during ARP initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-MQ_RECV Format: Message queue receive failed on %s queue: %s 

Explanation    An unexpected fatal error has occurred.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-MTS_BIND Format: Failed to do mts_bind for %s: %s 

Explanation    An unrecoverable software error has occurred during ARP initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-MTS_OPC_SET Format: Failed to register with opcode %d: %s 

Explanation    An unrecoverable software error has occurred during ARP initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-MTS_RECV Format: MTS queue receive failed on %s queue: %s 

Explanation    An unexpected fatal error has occurred.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-SET_SCHED Format: Failed to set policy or priority 

Explanation    An unrecoverable software error has occurred during ARP initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-SHM_ATTACH Format: Failed to attach %s shared memory 

Explanation    An unrecoverable software error has occurred during ARP initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-SVR_REG Format: Failed to register as a client of %s 

Explanation    An unrecoverable software error has occurred during ARP initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-SYSMGR_NOTIFY Format: Bad notification from sysmgr for %s 

Explanation    An unrecoverable software error has occurred during ARP initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-SYSMGR_QUERY Format: Failed to query sysmgr for %s 

Explanation    An unrecoverable software error has occurred during ARP initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-SYSMGR_UUID Format: Failed to get uuid from sysmgr during %s 

Explanation    An unrecoverable software error has occurred during ARP initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-THR_CREAT Format: Failed to create thread %s: error %d 

Explanation    An unrecoverable software error has occurred during ARP initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-THREAD_FAIL Format: Failed to start %s thread 

Explanation    An unrecoverable software error has occurred during ARP initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-TIMER_SET Format: Failed to initialize new timer set 

Explanation    An unrecoverable software error has occurred during ARP initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

Error Message     ARP-2-TIMERS_INIT Format: Failed to initialize timers 

Explanation    An unrecoverable software error has occurred during ARP initialization.

Recommended Action    Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.

ARP-3

Error Message     ARP-3-ADJ_ADD Format: Failed to add adjacency for received packet from 
%s on %s 

Explanation    Due to this failure, packet forwarding to this address will be affected until the next successful retry.

Recommended Action    No action is required.

Error Message     ARP-3-ADJ_UPD Format: Failed to update adjacency for received packet 
from %s on %s 

Explanation    Due to this failure, packet forwarding will continue to use the existing ARP adjacency entry values.

Recommended Action    No action is required.

Error Message     ARP-3-API_MQ_INVAL Format: ARP API Error: Invalid ARP message queue 
in %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-API_MQ_SEND Format: ARP API Error: Failed to send %s to %s 
queue: %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-API_MTS_INVAL Format: ARP API Error: Invalid ARP MTS queue in %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-API_MTS_SEND Format: ARP API Error: Failed to send %s to %s 
queue: %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-DAI_FETCH_ERR Format: DAI lookup failed, callback function 
returned 0x%x (%s) for %s %s 

Explanation    DAI lookup failed.

Recommended Action    No action is required.

Error Message     ARP-3-DUP_VADDR_SRC_IP Format: Source address of packet received from 
%s on %s(%s) is duplicate of local virtual ip, %s 

Explanation    There may be another router on this network that is configured with the same IP address.

Recommended Action    Check all routers on the interface for a misconfiguration.

Error Message     ARP-3-DUP_VADDR_SRCIP Format: Source address of packet received from 
%s on %s is duplicate of local virtual ip, %s 

Explanation    There may be another router on this network that is configured with the same IP address.

Recommended Action    Check all routers on the interface for a misconfiguration.

Error Message     ARP-3-DUP_VIRT_SRC_IP Format: Source address of packet received from 
%s on %s(%s) is duplicate of local virtual ip, %s 

Explanation    There may be another router on this network that is configured with the same IP address.

Recommended Action    Check all routers on the interface for a misconfiguration.

Error Message     ARP-3-DUP_VIRT_SRCIP Format: Source address of packet received from 
%s on %s is duplicate of local virtual ip, %s 

Explanation    There may be another router on this network that is configured with the same IP address.

Recommended Action    Check all routers on the interface for a misconfiguration.

Error Message     ARP-3-GRAT_ETH Format: Sending gratuitous arp for %s on invalid 
interface %s, not ethernet 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-GRAT_IOD Format: Sending gratuitous ARP for %s on an invalid 
interface %u 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-GRAT_IP Format: Sending gratuitous ARP request for %s IP address 
%s on %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-GRAT_NON_AM Format: Sending gratuitous arp for %s on invalid 
interface %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-GRAT_P2P Format: Sending gratuitous arp for %s on invalid 
interface %s, point-to-point 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-HDR_ERR Format: Failed to get ARP header, expected %d, got %d 
bytes 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-HDR_L2LEN_ERR Format: Received packet with incorrect layer 2 
address length (%d bytes) 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-HDR_L3LEN_ERR Format: Received packet with incorrect layer 3 
address length (%d bytes) 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-IF_INDEX Format: Invalid interface index received from %d 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-INVAL_HDR Format: Found incorrect hardware/protocol type in ARP 
header: %hu/%hu 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-INVAL_STATE Format: Unrecognized ARP entry state in timer 
callback: %lu 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-MAC_ERR Format: Failed to get MAC address on %s for %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-MBUF_ERR Format: Failed to get the remainder of packet, expected 
%d, got %d bytes 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-MTS_DROP Format: MTS drop failed on %s queue: %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-NO_MBUF Format: Failed to allocate buffer for %s 

Explanation    The system may have run out of packet memory buffers.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ARP-3-NO_MEM Format: Malloc failed for %s %s 

Explanation    The system may be low on memory.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ARP-3-PKT_ENCAP Format: Failed to encapsulate packet 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-PKT_OUT Format: Failed to send packet to PM 

Explanation    PM's message queue may be temporarily full.

Recommended Action    No action is required.

Error Message     ARP-3-REQ_ADD Format: Failed to add adjacency while sending request 
for %s on %s, request from pid: %d 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-REQ_ETH Format: Sending ARP request for %s on invalid interface 
%s, not ethernet, request from pid: %d 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-REQ_IOD Format: Sending ARP request for %s on an invalid 
interface %u, request from pid: %d 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-REQ_IP Format: Sending ARP request for %s IP address %s on %s, 
request from pid: %d 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-REQ_NON_AM Format: Sending ARP request for %s on invalid 
interface %s request from pid: %d 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-REQ_P2P Format: Sending ARP request for %s on invalid interface 
%s, point-to-point, request from pid: %d 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-TIMER_RSTART Format: Failed to restart timer 0x%p for %s on %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-VRRP_ETH Format: Adding vrrp arp for %s: invalid interface %s, 
not ethernet 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-VRRP_IOD Format: Adding vrrp arp for %s: invalid interface %u 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-VRRP_NON_AM Format: Sending vrrp arp for %s on invalid interface 
%s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-VRRP_P2P Format: Sending vrrp arp for %s on invalid interface 
%s, point-to-point 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-VRRPQ_ADD Format: Failed to add VRRP queue entry for %s, %s on %s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-3-VRRPQ_IP Format: Trying to add invalid IP address %s on %s to 
vrrp queue 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

ARP-4

Error Message     ARP-4-DIR_BCAST Format: %s address of packet received from %s on %s 
matches directed broadcast address, %s 

Explanation    There may be a configured subnet mask-length mismatch among router interfaces connected on this LAN.

Recommended Action    Check all routers on the interface for a misconfiguration.

Error Message     ARP-4-DUP_IP Format: ARP entry found with duplicate IP address %s on 
%s 

Explanation    There may be another router on this network that is configured with the same IP address.

Recommended Action    Check all routers on the interface for a misconfiguration.

Error Message     ARP-4-INVAL_IP Format: Received packet with invalid %s IP address (%s) 
from %s on %s 

Explanation    There may be a connected router sending packets with a bogus IP address.

Recommended Action    Check all routers on the interface for a misconfiguration.

Error Message     ARP-4-INVAL_MAC Format: Received packet with invalid %s MAC address 
(%s) from %s on %s 

Explanation    There may be a connected router sending packets with a bogus MAC address.

Recommended Action    Check all routers on the interface for a misconfiguration.

Error Message     ARP-4-OWN_SRCMAC Format: Received packet with a local source MAC 
address (%s) from %s on %s 

Explanation    There may be a connected router sending packets with local MAC address.

Recommended Action    Check all routers on the interface for a misconfiguration.

Error Message     ARP-4-SRCIP_ERR Format: Source address of received packet (%s) does 
not match subnet on interface %s 

Explanation    There may be a configured subnet mismatch among router interfaces connected on the LAN.

Recommended Action    Check all routers on the interface for a misconfiguration.

ARP-5

Error Message     ARP-5-MQ_MINOR Format: Received unknown minor message type (%d) from 
%s 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-5-MQ_UNEXP Format: Received unexpected message (%d/%d) on %s queue 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-5-MSG_UNK Format: Received unknown % type: %lu 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-5-MTS_OPC_UNK Format: Received unknown MTS opcode %lu 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-5-UNK_IP_NOTIF Format: Unrecognized IP address change 
notification type %lu 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-5-UNK_MSG_MINOR Format: Unrecognized %s message minor type %d 

Explanation    An unexpected but recoverable error has occurred.

Recommended Action    No action is required.

Error Message     ARP-5-UNK_SIG Format: Received unknown signal %d ; Explanation: An 
unexpected but recoverable error has occurred. 

Explanation    The system has detected an error.

Recommended Action    No action is required.

ASCII-CFG Messages

This section contains the ASCII-CFG messages.

ASCII-CFG-2

Error Message     ASCII-CFG-2-ACFG_CONFIGURATION_APPLY_ERROR: Error encountered while 
Ascii configuration was being applied. Please use show startup-config log to view 
details

Explanation    At least one command failed while the ASCII configuration was being applied.

Recommended Action    No action is required.

Error Message     ASCII-CFG-2-ACFG_LIB_INVOKE_ERR: Ascii config library invocation 
error: [chars] 

Explanation    The system has encountered an error while the library function was being invoked to display the ASCII configuration.

Recommended Action    No action is required.

Error Message     ASCII-CFG-2-ACFG_OPER_FAIL: Operation failed because of [chars] 

Explanation    Operation failed.

Recommended Action    No action is required.

Error Message     ASCII-CFG-2-ACFG_ROLLBACK_FAILED: Rollback to checkpoint [chars] 
Failed, Going to undo the changes (atomic option) 

Explanation    Rollback operation failed for atomic option.

Recommended Action    No action is required.

Error Message     ASCII-CFG-2-ACFG_ROLLBACK_UNDO_FAILED: Undo failed for atomic 
Rollback, Please correct the error manually and retry rollback 

Explanation    The system has encountered an error while undoing the rollback changes (for atomic behavior.

Recommended Action    No action is required.

Error Message     ASCII-CFG-2-ACFG_SYSLOG_INIT_FAILED: Ascii config Syslog Init Error 

Explanation    The system has encountered an error while initializing the syslog for the ASCII configuration.

Recommended Action    No action is required.

Error Message     ASCII-CFG-2-PSS_VER_FAIL: PSS file [chars] has version 
[dec].[dec].[dec], expected version [dec].[dec].[dec] 

Explanation    There was a mismatch in the PSS version. [chars] indicates the PSS service, [dec].[dec].[dec] its current version number and [dec].[dec].[dec] is the expected version.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ASCII-CFG-3

Error Message     ASCII-CFG-3-ACFG_MTSERROR: [chars] 

Explanation    Ascii-cfg-server (rollback process) encountered an MTS error. [chars] specifies the context where the error occurred.

Recommended Action    No action is required.

ASCII-CFG-6

Error Message     ASCII-CFG-6-ACFG_CHECKPOINT_CLEAR_DATABASE: cleared all the 
configuration checkpoints 

Explanation    The system has cleared all the configuration checkpoints.

Recommended Action    No action is required.

Error Message     ASCII-CFG-6-ACFG_CHECKPOINT_CREATED: Created configuration 
checkpoint [chars] 

Explanation    The system has created a configuration checkpoint.

Recommended Action    No action is required.

Error Message     ASCII-CFG-6-ACFG_CHECKPOINT_DELETED: Deleted configuration 
checkpoint [chars] 

Explanation    The system has deleted the configuration checkpoint.

Recommended Action    No action is required.

Error Message     ASCII-CFG-6-ACFG_MAX_CHECKPOINTS: Maximum no of checpoints reached, 
Removing the oldest checkpoint 

Explanation    The system detects that the maximum number of checkpoints has been reached and has removed the oldest checkpoint.

Recommended Action    No action is required.

Error Message     ASCII-CFG-6-ACFG_ROLLBACK_ATOMIC: Performing configuration rollback 
to checkpoint [chars] (with atomic option) 

Explanation    The system will perform a configuration rollback with the atomic option.

Recommended Action    No action is required.

Error Message     ASCII-CFG-6-ACFG_ROLLBACK_BEST: Performing configuration rollback to 
checkpoint [chars] (with best-effort option) 

Explanation    The system will perform a configuration rollback with the best-effort option.

Recommended Action    No action is required.

Error Message     ASCII-CFG-6-ACFG_ROLLBACK_FIRST_ERR: Performing configuration 
rollback to checkpoint [chars] (with stop-at-first failure option) 

Explanation    The system will perform a configuration rollback with the stop-at-first-failure option.

Recommended Action    No action is required.

Error Message     ASCII-CFG-6-INFORMATION: [chars] 

Explanation    An event happened that affects Acfg-Rollback. [chars] indicates the event.

Recommended Action    No action is required.

Error Message     ASCII-CFG-6-PSS_ERR: [chars] 

Explanation    An error occurred during an Acfg PSS operation. [chars] indicates the PSS operation that caused the error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ASCII_CFG Messages

This section contains the ASCII_CFG messages.

ASCII_CFG-2

Error Message     ASCII_CFG-2-ACFG_CONFIGURATION_APPLY_ERROR Format: Error encountered 
while Ascii configuration was being applied. Please use show startup-config log 
to view details 

Explanation    At least one command failed while the ASCII configuration was being applied.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASCII_CFG-2-ACFG_LIB_INVOKE_ERR Format: Ascii config library 
invocation error: %s 

Explanation    The system has encountered an error while the library function was being invoked to display the ASCII configuration.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASCII_CFG-2-ACFG_OPER_FAIL Format: Operation failed because of %s 

Explanation    operation failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASCII_CFG-2-ACFG_SYSLOG_INIT_FAILED Format: Ascii config Syslog Init 
Error 

Explanation    The system has encountered an error while initializing the syslog for the ASCII configuration.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASCII_CFG-2-PSS_VER_FAIL Format: PSS file %s has version %d.%d.%d 

Explanation    There was a mismatch in the PSS version. [chars] indicates the PSS service, [dec].[dec].[dec] its current version number and [dec].[dec].[dec] is the expected version.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ASCII_CFG-6

Error Message     ASCII_CFG-6-ACFG_CHECKPOINT_CLEAR_DATABASE Format: cleared all the 
configuration checkpoints 

Explanation    cleared all the configuration checkpoints.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASCII_CFG-6-ACFG_CHECKPOINT_CREATED Format: Created configuration 
checkpoint %s 

Explanation    created configuration checkpoint.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASCII_CFG-6-ACFG_CHECKPOINT_DELETED Format: Deleted configuration 
checkpoint %s 

Explanation    deleted configuration checkpoint.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASCII_CFG-6-ACFG_MAX_CHECKPOINTS Format: Maximum no of checpoints 
reached 

Explanation    The system detects that the maximum number of checkpoints has been reached and has removed the oldest checkpoint.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASCII_CFG-6-INFORMATION Format: %s 

Explanation    an event happened that affects Acfg-Rollback. [chars] indicates the event.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASCII_CFG-6-PSS_ERR Format: %s 

Explanation    an error occurred during an Acfg PSS operation. [chars] indicates the PSS operation that caused the error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ASSOC_MGR Messages

This section contains the ASSOC_MGR messages.

ASSOC_MGR-0

Error Message     ASSOC_MGR-0-EMERGENCY_MSG Format: %s 

Explanation    Association Manager Emergency Message.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASSOC_MGR-0-EMERGENCY_MSG: [chars] 

Explanation    Association Manager Emergency Message.

Recommended Action    Please file the bug for Association Manager Component thro' CDETS.

ASSOC_MGR-1

Error Message     ASSOC_MGR-1-ALERT_MSG Format: %s 

Explanation    Association Manager Alert Message.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASSOC_MGR-1-ALERT_MSG: [chars] 

Explanation    Association Manager Alert Message.

Recommended Action    Association Manager Internal Operation Alert.

ASSOC_MGR-2

Error Message     ASSOC_MGR-2-CRITICAL_MSG Format: %s 

Explanation    Association Manager Critical Message.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASSOC_MGR-2-CRITICAL_MSG: [chars] 

Explanation    Association Manager Critical Message.

Recommended Action    No action is required.

ASSOC_MGR-3

Error Message     ASSOC_MGR-3-ERROR_MSG Format: %s 

Explanation    Association Manager Error Message.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASSOC_MGR-3-ERROR_MSG: [chars] 

Explanation    Association Manager Error Message.

Recommended Action    No action is required.

ASSOC_MGR-4

Error Message     ASSOC_MGR-4-WARN_MSG Format: %s 

Explanation    Association Manager Warning Message.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASSOC_MGR-4-WARN_MSG: [chars] 

Explanation    Association Manager Warning Message.

Recommended Action    No action is required.

ASSOC_MGR-5

Error Message     ASSOC_MGR-5-NOTIF_MSG Format: %s 

Explanation    Association Manager Notification Message.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASSOC_MGR-5-NOTIF_MSG: [chars] 

Explanation    Association Manager Notification Message.

Recommended Action    No action is required.

ASSOC_MGR-6

Error Message     ASSOC_MGR-6-ASSOC_ACTIVATED Format: Association Activated for vlan 
id:%d <--> vsan id:%d 

Explanation    Association Activated.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASSOC_MGR-6-ASSOC_ACTIVATED: Association Activated for vlan id:[dec] 
<--> vsan id:[dec] 

Explanation    Association Activated.

Recommended Action    No action is required.

Error Message     ASSOC_MGR-6-ASSOC_CREATED Format: Association Created for vlan id:%d 
<--> vsan id:%d 

Explanation    Association Created.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASSOC_MGR-6-ASSOC_CREATED: Association Created for vlan id:[dec] <--> 
vsan id:[dec] 

Explanation    Association Created.

Recommended Action    No action is required.

Error Message     ASSOC_MGR-6-ASSOC_DEACTIVATED Format: Association Deactivated for 
vlan id: %d <--> vsan id: %d 

Explanation    Association Deactivated.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASSOC_MGR-6-ASSOC_DEACTIVATED: Association Deactivated for vlan id: 
[dec] <--> vsan id: [dec] 

Explanation    Association Deactivated.

Recommended Action    No action is required.

Error Message     ASSOC_MGR-6-ASSOC_DELETED Format: Association Deleted for vlan id: %d 
<--> vsan id: %d 

Explanation    Association Deleted.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASSOC_MGR-6-ASSOC_DELETED: Association Deleted for vlan id: [dec] 
<--> vsan id: [dec] 

Explanation    Association Deleted.

Recommended Action    No action is required.

Error Message     ASSOC_MGR-6-ASSOC_MGR_STATEFULL_RESTART: Association Manager 
Statefull Restart 

Explanation    Association Manager Stateful Restart.

Recommended Action    No action is required.

Error Message     ASSOC_MGR-6-ASSOC_MGR_STATELESS_RESTART: Association Manager 
Stateless Restart 

Explanation    Association Manager Stateless Restart.

Recommended Action    No action is required.

Error Message     ASSOC_MGR-6-ASSOC_OPER_STATUS_CHG Format: Association status for vlan 
id: %d <--> vsan id: %d changed from %s to %s 

Explanation    Association Operational State Change.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASSOC_MGR-6-ASSOC_OPER_STATUS_CHG: Association status for vlan id: 
[dec] <--> vsan id: [dec] changed from [chars] to [chars] 

Explanation    Association Operational State Change.

Recommended Action    No action is required.

Error Message     ASSOC_MGR-6-INFO_MSG Format: %s 

Explanation    ASSOC Manager Informational Message.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASSOC_MGR-6-INFO_MSG: [chars] 

Explanation    ASSOC Manager Informational Message.

Recommended Action    No action is required.

Error Message     ASSOC_MGR-6-STATEFULL_RESTART Format: Association Manager Statefull 
Restart 

Explanation    Association Manager Stateful Restart.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASSOC_MGR-6-STATELESS_RESTART Format: Association Manager Stateless 
Restart 

Explanation    Association Manager Stateless Restart.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

ASSOC_MGR-7

Error Message     ASSOC_MGR-7-DEBUG_MSG Format: %s 

Explanation    Association Manager Debug Message.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     ASSOC_MGR-7-DEBUG_MSG: [chars] 

Explanation    Association Manager Debug Message.

Recommended Action    No action is required.

AVANTI_LS Messages

This section contains the AVANTI_LS messages.

AVANTI_LS-0

Error Message     AVANTI_LS-0-NODE_EMERG_MSG Format: %s 

Explanation    Syslog message from a AVANTI_HELP_INTERFACEnode.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

AVANTI_LS-1

Error Message     AVANTI_LS-1-NODE_ALERT_MSG Format: %s 

Explanation    Syslog message from a AVANTI_HELP_INTERFACEnode.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

AVANTI_LS-2

Error Message     AVANTI_LS-2-NODE_CRIT_MSG Format: %s 

Explanation    Syslog message from a AVANTI_HELP_INTERFACEnode.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

AVANTI_LS-3

Error Message     AVANTI_LS-3-NODE_ERR_MSG Format: %s 

Explanation    Syslog message from a AVANTI_HELP_INTERFACEnode.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

AVANTI_LS-4

Error Message     AVANTI_LS-4-NODE_WARNING_MSG Format: %s 

Explanation    Syslog message from a AVANTI_HELP_INTERFACEnode.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

AVANTI_LS-5

Error Message     AVANTI_LS-5-NODE_NOTICE_MSG Format: %s 

Explanation    Syslog message from a AVANTI_HELP_INTERFACEnode.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

AVANTI_LS-6

Error Message     AVANTI_LS-6-NODE_INFO_MSG Format: %s 

Explanation    Syslog message from a AVANTI_HELP_INTERFACEnode.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

AVANTI_LS-7

Error Message     AVANTI_LS-7-NODE_DEBUG_MSG Format: %s 

Explanation    Syslog message from a AVANTI_HELP_INTERFACEnode.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

AVM Messages

This section contains the AVM messages.

AVM-2

Error Message     AVM-2-SVC_SYSLOG_INIT_FAILED Format: Initialization failed for SVC: 
%s 

Explanation    Initialization failed for SVC.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AVM-2-SVC_SYSLOG_NO_PORT_CHAN Format: Too many PortChannels allocated 
by user for interface %s 

Explanation    AVANTI_HELP_INTERFACEneeds port channels to operate. Too many PortChannels have been allocated by the user for the interface to operate correctly.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AVM-2-SVC_SYSLOG_PATH_FAILURE Format: System health detected SVC 
packet path failure for %s. 

Explanation    The CSM has been brought down by the system health monitor. System Health has detected a failure in the packet path between the SVC interface on the CSM and the backplane. This System Health test is run periodically.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AVM-2-SVC_SYSLOG_URIFS_FAILURE Format: %s is unreachable for reason: 
%s 

Explanation    AVANTI_HELP_INTERFACEmodflash is not accessible. Modflash is the name of the file system local to the SVC interface, and is typically used for coredumps and temporary file transfers.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

AVM-3

Error Message     AVM-3-SVC_SYSLOG_IF_INTERNAL_ERROR Format: Interface %s internal 
error: %s 

Explanation    AVANTI_HELP_INTERFACEinternal error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AVM-3-SVC_SYSLOG_LC_INTERNAL_ERROR Format: Unable to send MTS to 
linecard in slot %d: %s 

Explanation    Linecard MTS failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AVM-3-SVC_SYSLOG_NPORT_INTERNAL_ERROR Format: %s N-port for Interface 
%s 

Explanation    N-port internal error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

AVM-4

Error Message     AVM-4-SVC_SYSLOG_IF_INTERNAL_WARN Format: Interface %s internal 
warning: %s 

Explanation    AVANTI_HELP_INTERFACEinternal warning.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AVM-4-SVC_SYSLOG_NPORT_INTERNAL_WARN Format: %s N-port for Interface 
%s 

Explanation    AVANTI_HELP_INTERFACEinternal warning.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

AVM-5

Error Message     AVM-5-SVC_SYSLOG_IF_CONFIG_DELETED Format: Interface %s configuration 
was deleted%s 

Explanation    AVANTI_HELP_INTERFACEconfiguration was deleted.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AVM-5-SVC_SYSLOG_IF_DOWN Format: Interface %s is down 

Explanation    AVANTI_HELP_INTERFACEis down.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AVM-5-SVC_SYSLOG_IF_UP Format: Interface %s is up 

Explanation    AVANTI_HELP_INTERFACEis up.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

AVM-6

Error Message     AVM-6-SVC_SYSLOG_CL_CONFIG Format: Node %s has become config node of 
cluster %s 

Explanation    AVANTI_HELP_INTERFACEhas because cluster config node.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AVM-6-SVC_SYSLOG_CL_JOIN Format: Node %s has joined cluster %s 

Explanation    AVANTI_HELP_INTERFACEhas joined cluster.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AVM-6-SVC_SYSLOG_CL_UNJOIN Format: Node %s has left cluster %s 

Explanation    AVANTI_HELP_INTERFACEhas left cluster.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AVM-6-SVC_SYSLOG_LC_WWN_PURGE Format: All WWNs for module %d have been 
purged%s 

Explanation    AVANTI_HELP_LINECARDhas purged all WWNs.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     AVM-6-SVC_SYSLOG_VSAN_INACTIVE Format: Vsan %d suspended 

Explanation    VSAN was suspended; can cause warnings.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

BELLAGIO2 Messages

This section contains the BELLAGIO2 messages.

BELLAGIO2-2

Error Message     BELLAGIO2-2-CATASTROPHIC_FAILURE Format: Arbiter Catastrophic 
interrupt:%s 

Explanation    Arbiter trigerrored Catastrophic error interrupt.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BELLAGIO2-2-MBIST_FAIL Format: Arbiter MBIST failed:%s 

Explanation    Arbiter failed built in self test.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

BFD Messages

This section contains the BFD messages.

BFD-3

Error Message     BFD-3-SESSION_ACL_INSTALL_FAILED: BFD session [chars] failed due to 
missing ACL resources for interface [chars] 

Explanation    BFD session [chars] failed due to missing ACL resources for interface [chars].

Recommended Action    No action is required.

Error Message     BFD-3-SESSION_ACL_INSTALL_GAVE_UP Format: BFD session %s installation 
failed due to ACL installation failure interface %s 

Explanation    BFD session [chars] installation failed due to ACL installation failure interface [chars.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BFD-3-SESSION_ACL_INSTALL_GAVE_UP: BFD session [chars] installation 
failed due to ACL installation failure interface [chars]

Explanation    BFD session [chars] installation failed due to ACL installation failure interface [chars.

Recommended Action    Maximum acl install retries exceeded. Please to free up acl resources.

Error Message     BFD-3-SESSION_ACL_REMOVE_GAVE_UP Format: BFD session %s removal 
failed due to ACL removal failure interface %s 

Explanation    BFD session [chars] removal failed due to ACL removal failure interface [chars.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BFD-3-SESSION_ACL_REMOVE_GAVE_UP: BFD session [chars] removal failed 
due to ACL removal failure interface [chars]

Explanation    BFD session [chars] removal failed due to ACL removal failure interface [chars.

Recommended Action    Maximum acl removal retries exceeded. Please manually remove bfd sessions.

Error Message     BFD-3-SESSION_CREATE_FAIL Format: Failed to create BFD session to 
neighbor %s over intertface %s. Reason %s 

Explanation    Failed to create BFD session to neighbor [chars] over intertface [chars] Reason [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BFD-3-SESSION_CREATE_FAIL: Failed to create BFD session to neighbor 
[chars] over intertface [chars]. Reason [chars]

Explanation    Failed to create BFD session to neighbor [chars] over intertface [chars] Reason [chars].

Recommended Action    SYSLOGDPC_NO_ACTION.

BFD-4

Error Message     BFD-4-INVALID_NBR Format: Attempt to BFD session failed for 
application %s. 

Explanation    Attempt to BFD session failed for application [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BFD-4-INVALID_NBR: Attempt to BFD session failed for application 
[chars]. 

Explanation    Attempt to BFD session failed for application [chars].

Recommended Action    No action is required.

Error Message     BFD-4-INVALID_NBR: Attempt to register BFD session on invalid 
neighbor: [chars], by application=[chars]

Explanation    Attempt to register BFD session on invalid neighbor: [chars] type that is not supported by BFD for application [chars].

Recommended Action    No action is required.

Error Message     BFD-4-SESSION_DELETE_FAIL: Attempt to delete BFD session [chars] 
failed: Reason [chars] ([hex]).

Explanation    Attempt to delete [dec] BFD session[chars] failed: Reason [chars] ([hex]).

Recommended Action    No action is required.

Error Message     BFD-4-SESSION_DELETE_FAIL: Attempt to delete BFD session for neighbor 
[chars] failed: Reason [chars] ([hex]).

Explanation    Attempt to delete BFD session for neighbor [chars] failed: Reason [chars] ([hex]).

Recommended Action    No action is required.

BFD-5

Error Message     BFD-5-BFD_DISABLED: BFD Disabled 

Explanation    BFD Service Disabled.

Recommended Action    No action is required.

Error Message     BFD-5-BFD_ENABLED: BFD Enabled 

Explanation    BFD Service nabled.

Recommended Action    No action is required.

Error Message     BFD-5-BFD_SESSION_ADD: BFD session [hex] added 

Explanation    BFD Service Disabled.

Recommended Action    No action is required.

Error Message     BFD-5-BFD_SESSION_DOWN: BFD session [hex] down 

Explanation    BFD Service Disabled.

Recommended Action    No action is required.

Error Message     BFD-5-BFD_SESSION_REM: BFD session [hex] removed 

Explanation    BFD Service Disabled.

Recommended Action    No action is required.

Error Message     BFD-5-BFD_SESSION_UP: BFD session [hex] up 

Explanation    BFD Service Disabled.

Recommended Action    No action is required.

Error Message     BFD-5-DISABLED Format: BFD Disabled 

Explanation    BFD Service Disabled.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BFD-5-ENABLED Format: BFD Enabled 

Explanation    BFD Service enabled.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BFD-5-SESSION_ACTIVE_PARAMS_CHANGE Format: Local parameter of BFD 
session 0x%x has changed %s 

Explanation    Local parameter of BFD session [hex] has changed [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BFD-5-SESSION_ACTIVE_PARAMS_CHANGE: Local parameter of BFD session 
[hex] has changed [chars] 

Explanation    Local parameter of BFD session [hex] has changed [chars].

Recommended Action    No action is required.

Error Message     BFD-5-SESSION_CREATED Format: BFD session to neighbor %s on interface 
%s has been created 

Explanation    BFD session to neighbor [chars] on interface [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BFD-5-SESSION_CREATED: BFD session to neighbor [chars] on interface 
[chars] has been created 

Explanation    BFD session to neighbor [chars] on interface [chars].

Recommended Action    No action is required.

Error Message     BFD-5-SESSION_LOCAL_PARAMS_CHANGE Format: Local parameter of BFD 
session 0x%x has changed %s 

Explanation    Local parameter of BFD session [hex] has changed [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BFD-5-SESSION_LOCAL_PARAMS_CHANGE: Local parameter of BFD session 
[hex] has changed [chars] 

Explanation    Local parameter of BFD session [hex] has changed [chars].

Recommended Action    No action is required.

Error Message     BFD-5-SESSION_MOVED Format: BFD session 0x%x: %s 

Explanation    BFD session [hex]: [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BFD-5-SESSION_MOVED: BFD session [hex]: [chars] 

Explanation    BFD session [hex]: [chars].

Recommended Action    No action is required.

Error Message     BFD-5-SESSION_NO_RESOURCES Format: No resource for session to 
neighbor %s on interface %s 

Explanation    The BFD session cannot be created or modified due to lack of resources. No resources for session to neighbor [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BFD-5-SESSION_NO_RESOURCES: No resource for session to neighbor 
[chars] on interface [chars] 

Explanation    The BFD session cannot be created or modified due to lack of resources. No resources for session to neighbor [chars].

Recommended Action    Remove other BFD sessions to free resources for this session.

Error Message     BFD-5-SESSION_REMOVED Format: BFD session to neighbor %s on interface 
%s has been removed 

Explanation    BFD session to neighbor [chars] on interface [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BFD-5-SESSION_REMOVED: BFD session to neighbor [chars] on interface 
[chars] has been removed 

Explanation    BFD session to neighbor [chars] on interface [chars].

Recommended Action    No action is required.

Error Message     BFD-5-SESSION_STATE_DOWN Format: BFD session %s to neighbor %s on 
interface %s has gone down. Reason: 0x%x. 

Explanation    BFD session [chars] to neighbor [chars] on interface [chars] has gone down. Reason: [hex]. This may be as a result of the forwarding path being down.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BFD-5-SESSION_STATE_DOWN: BFD session [chars] to neighbor [chars] on 
interface [chars] has gone down. Reason: [hex].

Explanation    BFD session [chars] to neighbor [chars] on interface [chars] has gone down. Reason: [hex]. This may be as a result of the forwarding path being down.

Recommended Action    No action is required.

Error Message     BFD-5-SESSION_STATE_UP Format: BFD session %s to neighbor %s on 
interface %s is up. 

Explanation    BFD session [chars] to neighbor [chars] on interface [chars] is up.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BFD-5-SESSION_STATE_UP: BFD session [chars] to neighbor [chars] on 
interface [chars] is up. 

Explanation    BFD session [chars] to neighbor [chars] on interface [chars] is up.

Recommended Action    No action is required.

BFD-6

Error Message     BFD-6-SESSION_ACL_INSTALL_FAILED Format: BFD session %s failed due to 
missing ACL resources for interface %s 

Explanation    BFD session [chars] failed due to missing ACL resources for interface [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BFD-6-SESSION_ACL_INSTALL_FAILED: BFD session [chars] failed due to 
missing ACL resources for interface [chars] 

Explanation    BFD session [chars] failed due to missing ACL resources for interface [chars].

Recommended Action    No action is required.

Error Message     BFD-6-SESSION_ACL_REMOVE_FAILED Format: BFD session %s removal failed 
due to missing ACL resources for interface %s 

Explanation    BFD session [chars] removal failed due to missing ACL resources for interface [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BFD-6-SESSION_ACL_REMOVE_FAILED: BFD session [chars] removal failed 
due to missing ACL resources for interface [chars] 

Explanation    BFD session [chars] removal failed due to missing ACL resources for interface [chars].

Recommended Action    No action is required.

Error Message     BFD-6-SESSION_CREATED: BFD session to neighbor [chars] on interface 
[chars] has been created 

Explanation    BFD session to neighbor [chars] on interface [chars].

Recommended Action    No action is required.

Error Message     BFD-6-SESSION_LOCAL_PARAMS_CHANGE: Local parameter of BFD session 
[chars] has changed: [chars] 

Explanation    Local parameter of BFD session [chars] has changed: [chars].

Recommended Action    No action is required.

Error Message     BFD-6-SESSION_MOVED: BFD session [chars] has moved from [chars] to 
[chars] 

Explanation    BFD session [chars] has moved from [chars] to [chars].

Recommended Action    No action is required.

Error Message     BFD-6-SESSION_NO_RESOURCES: No resource for session to neighbor 
[chars] on interface [chars] 

Explanation    The BFD session cannot be created or modified due to lack of resources. No resources for session to neighbor [chars].

Recommended Action    Remove other BFD sessions to free resources for this session.

Error Message     BFD-6-SESSION_NO_RESOURCES_CLR: Lack of resources condition has 
cleared for session to neighbor [chars] on interface [chars] 

Explanation    Lack of resources condition has cleared for session to neighbor [chard] on interface [char].

Recommended Action    No action is required.

Error Message     BFD-6-SESSION_REMOVED: BFD session to neighbor [chars] on interface 
[chars] has been removed 

Explanation    BFD session to neighbor [chars] on interface [chars].

Recommended Action    No action is required.

Error Message     BFD-6-SESSION_STATE_DOWN: BFD session [chars] to neighbor [chars] on 
interface [chars] has gone down. Reason: [hex].

Explanation    BFD session [chars] to neighbor [chars] on interface [chars] has gone down. Reason: [hex]. This may be as a result of the forwarding path being down.

Recommended Action    No action is required.

Error Message     BFD-6-SESSION_STATE_UP: BFD session [chars] to neighbor [chars] on 
interface [chars] is up. 

Explanation    BFD session [chars] to neighbor [chars] on interface [chars] is up.

Recommended Action    No action is required.

BFDC-SLOT# Messages

This section contains the BFDC-SLOT# messages.

BFDC-SLOT#-2

Error Message     BFDC-SLOT#-2-BFDC_GENERAL_FAILURE: General failure. [chars] 

Explanation    General failure. This is a critical failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BFDC-SLOT#-2-BFDC_MALLOC_FAILED: Memory allocation failed. [chars] 

Explanation    Memory allocation failed. This is a critical failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BFDC-SLOT#-2-BFDC_MTS_FAILURE: MTS failure. [chars] 

Explanation    MTS related failure. This is a critical failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

BGP Messages

This section contains the BGP messages.

BGP-1

Error Message     BGP-1-FATAL Format: Fatal error: %s: %s 

Explanation    An unexpected fatal error has occurred.
Parameters: Error Type, Error ...

Recommended Action    Use the 'restart' command to restart the feature and clear this problem.

Error Message     BGP-1-UNKNOWNFATAL Format: Unknown fatal error %d: %s 

Explanation    An unexpected fatal error has occurred.
Parameters: Error Type, Error ...

Recommended Action    Use the 'restart' command to restart the feature and clear this problem.

BGP-2

Error Message     BGP-2-AFINIT Format: Error initializing address family, (%d) 

Explanation    An unrecoverable error has occurred during BGP initialization.

Recommended Action    Use the 'restart' command to restart the feature and clear this problem.

Error Message     BGP-2-AFINITFUNCS Format: Error initializing address family function 
vectors, (%d) 

Explanation    An unrecoverable error has occurred during BGP initialization.

Recommended Action    Use the 'restart' command to restart the feature and clear this problem.

Error Message     BGP-2-ATTACH Format: Unable to attach to %s 

Explanation    An unrecoverable error has occurred during BGP initialization.
Parameters: Server Name ...

Recommended Action    Use the 'restart' command to restart the feature and clear this problem.

Error Message     BGP-2-IPV6REG Format: Unable to register with IPv6 

Explanation    An unrecoverable error has occurred during BGP initialization.

Recommended Action    Use the 'restart' command to restart the feature and clear this problem.

Error Message     BGP-2-MQLOOP_INIT Format: Message queue loop %s, %s, Error - %s 

Explanation    An unrecoverable error has occurred during BGP initialization.
Parameters: MQLoop Type, Failure Type, Error ...

Recommended Action    Use the 'restart' command to restart the feature and clear this problem.

Error Message     BGP-2-PEERSHALTED Format: BGP %s shutdown due to no memory condition 
(%s) 

Explanation    The system may be low on memory.
Parameters: Peer(s), Error ...

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-2-PTHREAD Format: procket_pthread_create failed for %s: error %d 

Explanation    An unexpected fatal error has occurred.
Parameters: Thread Name, Error ...

Recommended Action    Use the 'restart' command to restart the feature and clear this problem.

Error Message     BGP-2-SRVREG Format: Unable to register with %s 

Explanation    An unrecoverable error has occurred during BGP initialization.
Parameters: Server Name ...

Recommended Action    Use the 'restart' command to restart the feature and clear this problem.

Error Message     BGP-2-SYSMGR_CONDVERIF Format: Sysmgr conditional verify failed 

Explanation    An internal software error occurred.

Recommended Action    Use the 'restart' command to restart the feature and clear this problem.

Error Message     BGP-2-SYSMGR_QUERY Format: Failed to query sysmgr for %s 

Explanation    An internal software error occurred.

Recommended Action    Use the 'restart' command to restart the feature and clear this problem.

Error Message     BGP-2-TSP_INIT Format: Unable to initialize with TSP 

Explanation    An unrecoverable error has occurred during BGP initialization.

Recommended Action    Use the 'restart' command to restart the feature and clear this problem.

Error Message     BGP-2-U6RIBREG Format: Unable to register with U6RIB for 
[afi/safi:%d/%d] 

Explanation    An unrecoverable error has occurred during BGP initialization.

Recommended Action    Use the 'restart' command to restart the feature and clear this problem.

Error Message     BGP-2-URIBREG Format: Unable to register with URIB for 
[afi/safi:%d/%d] 

Explanation    An unrecoverable error has occurred during BGP initialization.

Recommended Action    Use the 'restart' command to restart the feature and clear this problem.

BGP-3

Error Message     BGP-3-ALLOCFAIL Format: %s malloc (%ld) failed for: %s 

Explanation    The system may be low on memory.
Parameters: Alloc Type, Size, Error ...

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-APPLY_BESTPATH_CFG Format: Failed to apply bestpath 
configuration: %s 

Explanation    An unexpected but handleable event has occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-ASLEN Format: AS-PATH prepend length exceeds internal limit 

Explanation    The system has exceeded an internal limit when prepending an AS path.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-ASSERT Format: %s:%d: Assertion `%s' failed. 

Explanation    An internal software error occurred.
Parameters: File Name, Line Number, Assert Type ...

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-BADPEERAS Format: VRF %s, Peer %s - bad remote-as, expecting %s 
received %s. 

Explanation    The system has detected an error when prepending to an AS path.
Parameters: Segment Type, Segment Length ...

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-BFD_SEND_AUTO_EXPIRY Format: Unable to start BFD staling, error 
%s(0x%08x) 

Explanation    An unexpected but handleable event has occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-BFD_SEND_EXPIRE_NOW Format: Unable to expire staled BFD 
sessions, error %s(0x%08x) 

Explanation    An unexpected but handleable event has occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-BFD_SES_ADD Format: Unable to add BFD session for peer %s, error 
%s 

Explanation    An unexpected but handleable event has occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-BFD_SES_CREATE Format: Unable to create BFD session Id for peer 
%s, error %s 

Explanation    An unexpected but handleable event has occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-BFD_SES_REMOVE Format: Unable to remove BFD session for peer 
%s, error %s 

Explanation    An unexpected but handleable event has occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-BFD_SES_REMOVE_ALL Format: Unable to cleanup the BFD sessions 
during deconfiguration, error %s(0x%08x) 

Explanation    An unexpected but handleable event has occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-COMADD Format: Error occurred in community addition, no action 
taken 

Explanation    An internal error was encountered in adding a community.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-COMLEN Format: Community sets exceeded maximum allowed limit 

Explanation    An internal limit was hit in adding a community.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-CONDSRV_CLEANUP Format: Conditional Service cleanup request 
failed, %s 

Explanation    Sysmgr rejected BGP's request to shut down.

Recommended Action    No action is required.

Error Message     BGP-3-EBGPTTL Format: Unable to set EBGP TTL for peer %s, fd %d 

Explanation    An unexpected but handleable event has occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-EVENT_WAIT Format: Error while waiting for %s event, error - 
%s\n 

Explanation    An unexpected but handleable event has occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-EXTCOMADD Format: Error occurred in extended community 
addition, no action taken 

Explanation    An internal error was encountered in adding an extended community.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-EXTCOMLEN Format: Extended community sets exceeded maximum 
allowed limit 

Explanation    An internal limit was hit in adding an extended community.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-ILLARGS Format: %s called with illegal arguments 

Explanation    An internal software error occurred.
Parameters: Function ...

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-INTERNAL Format: Internal error %d: %s 

Explanation    An internal software error occurred.
Parameters: Error Type, Error ...

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-INVHDR Format: Peer %s sent unexpected header pattern 

Explanation    The marker pattern in the message header was invalid.

Recommended Action    Check that the peer router is configured correctly. Clear the peer if necessary after any change.

Error Message     BGP-3-IPTOS Format: Unable to set IP TOS bits for %s, fd %d 

Explanation    An unexpected but handleable event has occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-LISTEN_SOCK Format: Failed to listen on %s BGP TCP port 

Explanation    BGP_EXPL_SOCK_ERROR
Parameters: Address-family ...

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-LOWMEM Format: Low on heap memory 

Explanation    The system may be low on memory.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-MD5PASS Format: Cannot set MD5 password %s for peer %s 

Explanation    An internal software error occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-MQLOOP_SHUTDOWN Format: Couldn't shut down %s message queue loop 

Explanation    An unexpected but handleable event has occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-NBRERR Format: %s Peer error: %s 

Explanation    An internal software error occurred.
Parameters: Peer address, Error ...

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-NEGWRITE Format: Negative nr of %d bytes left to write to peer %s 

Explanation    An internal software error occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-NOBUF Format: [%s] Unable to get buffer for %s msg to peer %s 

Explanation    An internal software error occurred.
Parameters: Address-family, Msg Type, Peer address ...

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-NOMEMORY Format: Could not allocate %s 

Explanation    The system may be low on memory.
Parameters: Data Type ...

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-PATH_DEL Format: Failed to destroy path (%s), error %d 

Explanation    The BGP process may have run out of memory.
Parameters: Path Type, Error ...

Recommended Action    If BGP ran out of memory, add memory to the router or change the network configuration to decrease memory requirements. Clear any BGP peers that may have been shut down automatically. If BGP has available memory, restart BGP.

Error Message     BGP-3-PATH_STALE Format: [%s] %s path being %s, for %s/%d from peer 
%s, should not be stale 

Explanation    An internal software error occurred.
Parameters: Address-family, Path State, Operation, Prefix/masklength, Peer address ...

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-PFX_NOMEM Format: Could not allocate %s for %s/%d 

Explanation    The system may be low on memory.
Parameters: Data Type, Prefix/masklength ...

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-RESTARTINIT Format: Unable to determine restart status and 
initialize 

Explanation    An unrecoverable error has occurred during BGP initialization.

Recommended Action    Use the 'restart' command to restart the feature and clear this problem.

Error Message     BGP-3-RESTARTTYPE Format: Error in learning restart type 

Explanation    An internal software error occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-RNHCB Format: RNH %s error: %s 

Explanation    An internal software error occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-SENDBUF Format: Error manipulating sendbuf: %s 

Explanation    An internal software error occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-SNMP_API_DATA Format: Message data is NULL 

Explanation    An SNMP message does not have enough memory to store data.

Recommended Action    No action is required.

Error Message     BGP-3-SOCK_ACCEPT Format: Socket (%d/%d) accept: %s\n 

Explanation    BGP_EXPL_SOCK_ERROR
Parameters: Socket fds, Error ...

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-SOCK_ERR Format: Socket (%d/%d): %s\n 

Explanation    BGP_EXPL_SOCK_ERROR
Parameters: Socket fds, Error ...

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-SOCK_FDPOP Format: Unexpected error during socket fd population 
%s(%d) 

Explanation    An unexpected but handleable event has occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-SOCK_RECV Format: Unexpected error during socket data recv 
%s(%d) 

Explanation    An unexpected but handleable event has occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-SOCKBIND Format: Cannot bind local socket for peer %s: %s 

Explanation    An error occurred during a socket operation.
Parameters: Peer address, Error ...

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-SOCKCREATE Format: Cannot create socket for peer %s: %s, stats: 
%lu/%lu/%lu/%lu/%lu 

Explanation    An error occurred during a socket operation.
Parameters: Peer address, Error, Socket stats ...

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-SOCKNONBLOCK Format: Couldn't make fd %d non-blocking: %s 

Explanation    An error occurred during a socket operation.
Parameters: Socket fd, Error ...

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-SOCKOPEN Format: TCP connection for peer %s already open, fd 
%d, state %s 

Explanation    An internal software error occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-SOFTINCAP Format: Peer %s not capable of soft refresh in, 
operator intervention needed: %s 

Explanation    The router is unable to do a soft refresh for the indicated peer.

Recommended Action    If necessary, reset the connection with the peer.

Error Message     BGP-3-SRAND Format: Failed to set random seed 

Explanation    An unrecoverable error has occurred during BGP initialization.

Recommended Action    Use the 'restart' command to restart the feature and clear this problem.

Error Message     BGP-3-THREAD_SHUTDOWN Format: Problem shutting down thread %s: 
Operation - %s, Error - %s\n 

Explanation    An unexpected but handleable event has occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-TIMER_START Format: Couldn't start %s timer %s 

Explanation    An internal software error occurred.
Parameters: Timer Type, Data ...

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-U6RIBRNH Format: U6RIB RNH error: %s 

Explanation    An internal software error occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-ULIBREG Format: Unable to register with ULIB for 
[afi/safi:%d/%d] 

Explanation    An unrecoverable error has occurred during BGP initialization.

Recommended Action    Use the 'restart' command to restart the feature and clear this problem.

Error Message     BGP-3-ULIBRNH Format: ULIB RNH error: %s 

Explanation    An internal software error occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-UNEXPECT Format: %s L%d: %s 

Explanation    An internal software error occurred.
Parameters: File Name, Line Number, Unexpected condition ...

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-URIBRNH Format: URIB RNH error: %s 

Explanation    An internal software error occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-3-URIBRT Format: URIB RT error: %s 

Explanation    An internal software error occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

BGP-4

Error Message     BGP-4-ISSU_CHECK Format: Not ready for ISSU: Graceful Restart or hold 
time check failed 

Explanation    No user action is required.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-4-ISSU_HOLDTIME Format: ISSU will be affected if hold time is less 
than or equal to system switchover time (%d seconds)\n 

Explanation    No user action is required.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BGP-4-NODAMPMEM Format: [%s] Unable to dampen prefix %s/%d from peer 
%s due to no memory 

Explanation    BGP_EXPL_NO_MEMORY
Parameters: Address-family, Prefix/masklength, Peer address ...

Recommended Action    No action is required.

Error Message     BGP-4-NORID Format: Peer %s sent us 0.0.0.0 as its router-id 

Explanation    A BGP peer sent us an invalid router ID.

Recommended Action    Check that the peer router is configured correctly. Clear the peer if necessary after any change.

Error Message     BGP-4-SAMERID Format: Peer %s uses same routerid as us 

Explanation    A BGP peer is using the same router ID as this router.

Recommended Action    Configure either the local or remote router with a different router ID.

Error Message     BGP-4-SNMP_REGFAIL Format: Failed to register MIB with the SNMP agent, 
the BGP MIB will be unavailable. (%s)\n 

Explanation    No user action is required.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

BGP-5

Error Message     BGP-5-BADSIG Format: Should not have received signal %d 

Explanation    An unexpected but handleable event has occurred.

Recommended Action    No action is required.

BIOS_DAEMON Messages

This section contains the BIOS_DAEMON messages.

BIOS_DAEMON-2

Error Message     BIOS_DAEMON-2-BIOS_DAEMON_FLASH_WARNING: Flash chip not supported by 
running image. Skipping bios upgrade. 

Explanation    BIOS CHIP NOT SUPPORTED.

Recommended Action    No action is required.

Error Message     BIOS_DAEMON-2-BIOS_DAEMON_PRI_BOOT_FAIL: Primary BIOS is corrupted or 
un-bootable 

Explanation    The system detects that the primary BIOS has been corrupted.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BIOS_DAEMON-2-BIOS_DAEMON_PRI_BOOT_FAIL: System booted from Alternate 
BIOS Flash 

Explanation    Boot from Alternate.

Recommended Action    SYSLOGDOC_NOACTION.

Error Message     BIOS_DAEMON-2-BIOS_DAEMON_SUP_ERROR: BIOS Sector ([dec]) is write 
protected 

Explanation    The system detects that the BIOS write has been protected.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BIOS_DAEMON-2-FLASH_WARNING Format: Flash chip not supported by 
running image. Skipping bios upgrade. 

Explanation    BIOS CHIP NOT SUPPORTED.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BIOS_DAEMON-2-PRI_BOOT_FAIL Format: System booted from Alternate BIOS 
Flash 

Explanation    Boot from Alternate.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

BIOS_DAEMON-5

Error Message     BIOS_DAEMON-5-BIOS_DAEMON_PRI_BOOT: System booted from Primary BIOS 
Flash 

Explanation    Boot from Primary.

Recommended Action    SYSLOGDOC_NOACTION.

Error Message     BIOS_DAEMON-5-PRI_BOOT Format: System booted from Primary BIOS Flash 

Explanation    Boot from Primary.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

BIOS_DAEMON-SLOT# Messages

This section contains the BIOS_DAEMON-SLOT# messages.

BIOS_DAEMON-SLOT#-2

Error Message     BIOS_DAEMON-SLOT#-2-BIOS_DAEMON_LC_ERROR: BIOS Sector ([dec]) is 
write protected 

Explanation    The system detects that the BIOS write has been protected.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BIOS_DAEMON-SLOT#-2-BIOS_DAEMON_LC_PRI_BOOT_FAIL: Primary BIOS is 
corrupted or un-bootable 

Explanation    The system detects that the primary BIOS has been corrupted.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BIOS_DAEMON-SLOT#-2-BIOS_DAEMON_LC_PRI_BOOT_FAIL: System booted from 
Alternate BIOS Flash 

Explanation    Boot from Alternate.

Recommended Action    SYSLOGDOC_NOACTION.

BIOS_DAEMON-SLOT#-5

Error Message     BIOS_DAEMON-SLOT#-5-BIOS_DAEMON_LC_PRI_BOOT: System booted from 
Primary BIOS Flash 

Explanation    Boot from Primary.

Recommended Action    SYSLOGDOC_NOACTION.

BOOTUP_TEST Messages

This section contains the BOOTUP_TEST messages.

BOOTUP_TEST-2

Error Message     BOOTUP_TEST-2-EOBC_FAIL Format: Module %d has failed test %s on EOBC 
due to error %s 

Explanation    The online diagnostic EOBC test has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTUP_TEST-2-EOBC_FAIL: Module [dec] has failed test [chars] on EOBC 
due to error [chars] 

Explanation    The online diagnostic EOBC test has failed.

Recommended Action    No action is required.

Error Message     BOOTUP_TEST-2-EOBC_SKIP Format: Module %d has failed test %s on EOBC 
due to error %s 

Explanation    The online diagnostic ManagementPort test has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTUP_TEST-2-EOBC_SKIP: Module [dec] has failed test [chars] on EOBC 
due to error [chars] 

Explanation    The online diagnostic ManagementPort test has failed.

Recommended Action    No action is required.

Error Message     BOOTUP_TEST-2-MGMT_PORT_FAIL Format: Module %d has failed test %s on 
Management Port due to error %s 

Explanation    The online diagnostic ManagementPort test has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTUP_TEST-2-MGMT_PORT_FAIL: Module [dec] has failed test [chars] on 
Management Port due to error [chars] 

Explanation    The online diagnostic ManagementPort test has failed.

Recommended Action    No action is required.

Error Message     BOOTUP_TEST-2-MGMT_PORT_SKIP Format: Module %d has skipped test %s on 
Management Port due to error %s 

Explanation    The online diagnostic ManagementPort test is skipped.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTUP_TEST-2-MGMT_PORT_SKIP: Module [dec] has skipped test [chars] 
on Management Port due to error [chars] 

Explanation    The online diagnostic ManagementPort test is skipped.

Recommended Action    No action is required.

BOOTVAR Messages

This section contains the BOOTVAR messages.

BOOTVAR-2

Error Message     BOOTVAR-2-ALLOC_MEMORY Format: Memory allocation failed 

Explanation    The service failed to allocate memory.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTVAR-2-ALLOC_MEMORY: Memory allocation failed 

Explanation    The service failed to allocate memory.

Recommended Action    Check if the system is low on memory, if so, reset the switch.

Error Message     BOOTVAR-2-AUTOCOPY_FAILED: Autocopy of file [chars] to standby 
failed. [chars] (Error-id: [hex]) 

Explanation    The image to be copied to standby vi the auto-copy feature failed.

Recommended Action    Check error id for specified reason.

Error Message     BOOTVAR-2-AUTOSYNC_FAILED: Image autosync failed. Reason: [chars] 
([hex]) 

Explanation    Image synchronization failed.

Recommended Action    Check that there is enough space on the flash, and check the system high availability status.

Error Message     BOOTVAR-2-CONFIG_ERROR Format: Failed to update boot configuration 

Explanation    An error has occurred during the update of the boot configuration files.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTVAR-2-CONFIG_ERROR: Failed to update boot configuration 

Explanation    An error has occurred during the update of the boot configuration files.

Recommended Action    Check that there is enough space on the flash, enter the show boot command to check the configured image names, enter the show loader internal command to compare the configurations, if the configurations do not match, enter the write erase command and retry saving the configuration.

Error Message     BOOTVAR-2-IMAGE_NOT_COMPATIBLE Format: Warning: image %s is not 
compatible with the current platform in SUP %d 

Explanation    The input image name is not compatible with the current platform.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTVAR-2-IMAGE_NOT_COMPATIBLE: Warning: image [chars] is not 
compatible with the current platform in SUP [dec] 

Explanation    The input image name is not compatible with the current platform.

Recommended Action    Make sure that the system has the correct image before you reboot.

BOOTVAR-3

Error Message     BOOTVAR-3-AUTOCOPY_FAILED_STANDBY_FULL Format: Autocopy of file %s to 
standby failed due to not enough disk space on standby 

Explanation    There is not enough disk space on the standby for the file to be copied.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTVAR-3-AUTOCOPY_FAILED_STANDBY_FULL: Autocopy of file [chars] to 
standby failed due to not enough disk space on standby

Explanation    There is not enough disk space on the standby for the file to be copied.

Recommended Action    Clear space on the standby disk.

Error Message     BOOTVAR-3-INIT_FAILED Format: Initialization failed: Component %s 

Explanation    The system detects that the service has failed to start. The failure occurs during initialization of the component [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTVAR-3-INIT_FAILED: Initialization failed: Component [chars] 

Explanation    The system detects that the service has failed to start. The failure occurs during initialization of the component [chars].

Recommended Action    Enter the show processes command to check the status of the other processes, pay attention to the specified component.

Error Message     BOOTVAR-3-LOAD_VERIFY_LIB_FAILED Format: Fetching library %s failed 

Explanation    The system has failed to load bootvar that is specified in the verification library.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTVAR-3-LOAD_VERIFY_LIB_FAILED: Fetching library [chars] failed, 
reason=[chars] 

Explanation    The system has failed to load bootvar that is specified in the verification library.

Recommended Action    No action is required.

Error Message     BOOTVAR-3-MODULE_LOCK_FAIL Format: Unable to get module lock 

Explanation    unable to acquire modlock to prevent the user to reload duringautosynchronization.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTVAR-3-MODULE_LOCK_FAIL: Unable to get module lock, please don't 
reload <error-id:[hex]> 

Explanation    The system is unable to acquire modlock to prevent the user to reload duringautosynchronization.

Recommended Action    No action is required.

Error Message     BOOTVAR-3-NEIGHBOR_REJECT_AUTOCOPY Format: auto-copy failed - not 
supported by neighbor supervisor. 

Explanation    The autocopy has failed because it is not supported by the standby supervisor module.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTVAR-3-NEIGHBOR_REJECT_AUTOCOPY: auto-copy failed - not supported 
by neighbor supervisor. 

Explanation    The autocopy has failed because it is not supported by the standby supervisor module.

Recommended Action    No action is required.

Error Message     BOOTVAR-3-VERIFY_FAILED Format: Image %s for bootvar %s verification 
failed 

Explanation    The image set for this bootvar has failed the verification process.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTVAR-3-VERIFY_FAILED: Image [chars] for bootvar [chars] 
verification failed, reason=[chars] 

Explanation    The image set for this bootvar has failed the verification process.

Recommended Action    Check reason to determine actions.

BOOTVAR-5

Error Message     BOOTVAR-5-AUTOCOPY_SUCCEED Format: auto-copy of file %s to standby 
supervisor succeed 

Explanation    auto copy of the file succeed, image integrity verified by standby.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTVAR-5-AUTOCOPY_SUCCEED: auto-copy of file [chars] to standby 
supervisor succeed 

Explanation    The autocopy of the file has succeeded. The image integrity has been verified by the standby supervisor module.

Recommended Action    No action is required.

Error Message     BOOTVAR-5-AUTOCOPY_VERIFY_SEND_FAILED Format: Unable to ask standby 
to verify file %s 

Explanation    When the image was copied to the standby supervisor module, the system failed to ask the standby supervisor module to verify the integrity of the image.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTVAR-5-AUTOCOPY_VERIFY_SEND_FAILED: Unable to ask standby to 
verify file [chars], error = [hex] 

Explanation    When the image was copied to the standby supervisor module, the system failed to ask the standby supervisor module to verify the integrity of the image.

Recommended Action    Turn auto-copy off and back on.

Error Message     BOOTVAR-5-AUTOSYNC_DONE Format: Image autosync done 

Explanation    The image synchronization was successful.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTVAR-5-AUTOSYNC_DONE: Image autosync done 

Explanation    The image synchronization was successful.

Recommended Action    No action is required.

Error Message     BOOTVAR-5-AUTOSYNC_REBOOT Format: Rebooting standby after successful 
autosync 

Explanation    The image autosynchronization has been successful. The system is resetting the standby supervisor to load the new image.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTVAR-5-AUTOSYNC_REBOOT: Rebooting standby after successful 
autosync 

Explanation    The image autosynchronization has been successful. The system is resetting the standby supervisor to load the new image.

Recommended Action    Check that the standby supervisor module reloads correctly.

Error Message     BOOTVAR-5-AUTOSYNC_START Format: Starting image autosync. Please wait 
until completion... 

Explanation    The standby supervisor module has requested the synchronizationof the current image.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTVAR-5-AUTOSYNC_START: Starting image autosync. Please wait until 
completion... 

Explanation    The standby supervisor module has requested the synchronizationof the current image.

Recommended Action    No action is required.

Error Message     BOOTVAR-5-IMAGE_NOTEXISTS Format: Warning: image %s doesn't exist on 
sup%d 

Explanation    The input image name does not exist on the specified supervisor.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTVAR-5-IMAGE_NOTEXISTS: Warning: image [chars] doesn't exist on 
sup[dec] 

Explanation    The input image name does not exist on the specified supervisor.

Recommended Action    Check whether the input image name you entered exists and make sure that you have the image on the flash before you reboot.

Error Message     BOOTVAR-5-NEIGHBOR_UPDATE_AUTOCOPY Format: auto-copy supported by 
neighbor supervisor 

Explanation    The information log reports that the standby supervisor module supports autocopy. Autocopy is being started.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTVAR-5-NEIGHBOR_UPDATE_AUTOCOPY: auto-copy supported by neighbor 
supervisor, starting... 

Explanation    The information log reports that the standby supervisor module supports autocopy. Autocopy is being started.

Recommended Action    No action is required.

BOOTVAR-6

Error Message     BOOTVAR-6-ALREADY_IN_SYNC Format: Image already in sync 

Explanation    This message indicates that you do not need to update the image on the standby supervisor module.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTVAR-6-ALREADY_IN_SYNC: Image already in sync 

Explanation    This message indicates that you do not need to update the image on the standby supervisor module.

Recommended Action    No action is required.

Error Message     BOOTVAR-6-AUTOCOPY_DID_NOT_START: Autocopy of file [chars] to standby 
did not start. [chars] (Error-id: [hex])

Explanation    Autocopy of the file did not start as the remote copy location does not exist.

Recommended Action    No action is required.

Error Message     BOOTVAR-6-CONFIG_UPDATED Format: Boot configuration updated 

Explanation    The boot-loader configuration files have been successfully updated.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTVAR-6-CONFIG_UPDATED: Boot configuration updated 

Explanation    The boot-loader configuration files have been successfully updated.

Recommended Action    No action is required.

Error Message     BOOTVAR-6-STARTING Format: Boot configuration initialized 

Explanation    The service has successfully started.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     BOOTVAR-6-STARTING: Boot configuration initialized 

Explanation    The service has successfully started.

Recommended Action    No action is required.

CALLHOME Messages

This section contains the CALLHOME messages.

CALLHOME-2

Error Message     CALLHOME-2-EVENT Format: %s 

Explanation    A Call Home event [chars] occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CALLHOME-2-EVENT: [chars] 

Explanation    A Call Home event [chars] occurred.

Recommended Action    If you have configured your e-mail address to receive Call Home notifications, check your email for more details about this callhome event. If callhome was not enabled, execute commands relevant to the callhome event to get more information about the error.

Error Message     CALLHOME-2-PROGRAM_EXIT Format: callhome process ending: %s\n 

Explanation    A Call Home process is exiting with the reason [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CALLHOME-2-PROGRAM_EXIT: callhome process ending: [chars] 

Explanation    A Call Home process is exiting with the reason [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CALLHOME-3

Error Message     CALLHOME-3-CALLHOME_CFS_MERGE_OPERATION_FAILED: [chars] 

Explanation    [chars1].

Recommended Action    Check the reason for the failure of the CFS operation and fix the problem.

Error Message     CALLHOME-3-CALLHOME_CFS_OPERATION_FAILED: [chars] : [chars] 

Explanation    [chars1] [chars2].

Recommended Action    Check the reason for the failure of the CFS operation and fix the problem.

Error Message     CALLHOME-3-CALLHOME_MAX_ALERT_MSG: [chars] 

Explanation    [chars].

Recommended Action    Check the reason for the generation of the Call Home messages and fix the problem.

Error Message     CALLHOME-3-CFS_MERGE_OPERATION_FAILED Format: %s 

Explanation    [chars1].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CALLHOME-3-CFS_OPERATION_FAILED Format: %s : %s 

Explanation    [chars1] [chars2].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CALLHOME-3-EVENT_PROCESS_ERROR Format: error in processing callhome 
event %s reason:%s 

Explanation    An error has occurred when processing the Call Home event [chars] reason:[chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CALLHOME-3-EVENT_PROCESS_ERROR: error in processing callhome event 
[chars] reason:[chars] 

Explanation    An error has occurred when processing the Call Home event [chars] reason:[chars].

Recommended Action    Check that Call Home is properly configured on your system. Check the SMTP server address, e-mail addresses for destination profiles and enable Call Home. Use show Call Home commands for displaying the configuration.

Error Message     CALLHOME-3-MAX_ALERT_MSG Format: %s 

Explanation    [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CALLHOME-3-MESSAGE_SIZE_EXCEED Format: message size for callhome 
alert:%s exceeds maximum limit for destination profile:%s 

Explanation    The message size for Call Home alert:[chars] exceeds the maximum limit for destination profile:[chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CALLHOME-3-MESSAGE_SIZE_EXCEED: message size for callhome 
alert:[chars] exceeds maximum limit for destination profile:[chars]

Explanation    The message size for Call Home alert:[chars] exceeds the maximum limit for destination profile:[chars].

Recommended Action    Check the maximum message size for the destination profile . Increase it if possible to match the maximum limit allowed by your e-mail destinations.

CALLHOME-6

Error Message     CALLHOME-6-NONCRIT_EVENT Format: %s 

Explanation    A noncritical Call Home event [chars] occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CALLHOME-6-NONCRIT_EVENT: [chars] 

Explanation    A noncritical Call Home event [chars] occurred.

Recommended Action    If you have configured your e-mail address to receive Call Home notifications, check your email for more details about this callhome event. If callhome was not enabled, execute commands relevant to the callhome event to get more information about the error.

CDP Messages

This section contains the CDP messages.

CDP-2

Error Message     CDP-2-INITFAIL: CDP Daemon Initialization failed: [chars] 

Explanation    CDP daemon initialization failed. [chars] explains the reason for the failure.

Recommended Action    No action is required.

CDP-3

Error Message     CDP-3-ALLOCFAIL: Heap Memory allocation failed: [chars] 

Explanation    The CDP daemon is out of dynamic memory. [chars] specifies the context where the failure occurred.

Recommended Action    No action is required.

Error Message     CDP-3-GENERROR: [chars] 

Explanation    The CDP daemon encountered a generalerror thatdoes not fall in any of the above categories. [chars] describes the error and its context.

Recommended Action    No action is required.

Error Message     CDP-3-MCASTBINDFAIL: Failed to bind for CDP multicast address on 
interface [hex] - [chars]

Explanation    An attempt to register for packets destined to the CDP multicast address failed. [dec] identifies the interface and [char] identifies the reason.

Recommended Action    No action is required.

Error Message     CDP-3-MTSERROR: [chars] 

Explanation    The CDP daemon encountered an MTS error. [chars] specifies the context where the error occurred.

Recommended Action    No action is required.

Error Message     CDP-3-PKTRECVFAIL: Failed to receive packet - [chars] 

Explanation    The system has failed to receive the packet. [char] identifies the reason.

Recommended Action    No action is required.

Error Message     CDP-3-PKTSENDFAIL: Failed to send packet, interface [hex] - [chars] 

Explanation    The system has failed to send the packet. [dec] identifies the interface and [char] identifies the reason.

Recommended Action    No action is required.

Error Message     CDP-3-PSSERROR: [chars] 

Explanation    The CDP daemon encountered a PSS error. [chars] specifies the context where the failure occurred.

Recommended Action    No action is required.

Error Message     CDP-3-SOCKBINDFAIL: Failed to bind to raw socket, interface [hex] - 
[chars] 

Explanation    The system has failed to bind to a raw socket. [dec] identifies the interface and [char] identifies the reason.

Recommended Action    No action is required.

Error Message     CDP-3-SOCKOPENFAIL: Failed to open socket for receiving raw 802_2 
packets - [chars] 

Explanation    An attempt to open a socket for receiving raw 802_2 packets failed. [char] identifies the reason.

Recommended Action    No action is required.

CDP-4

Error Message     CDP-4-DUPLEX_MISMATCH: Duplex mismatch discovered on [chars], with 
[chars] 

Explanation    A duplex mismatch has been discovered from the received CDP packet.

Recommended Action    No action is required.

Error Message     CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on 
[chars]([dec]), with [chars]([dec]) 

Explanation    A native VLAN mismatch has been discovered.

Recommended Action    No action is required.

CDP-5

Error Message     CDP-5-DISABLED: CDP is disabled 

Explanation    CDP is disabled on the device.

Recommended Action    No action is required.

Error Message     CDP-5-ENABLED: CDP is enabled 

Explanation    CDP is enabled on the device.

Recommended Action    No action is required.

CDP-6

Error Message     CDP-6-CDPDUP: CDP Daemon Up. 

Explanation    The CDP daemon was created successfully and is up and running.

Recommended Action    No action is required.

Error Message     CDP-6-CDPEXIT: CDP Daemon shutting down gracefully. 

Explanation    The CDP daemon is shutting down gracefully.

Recommended Action    No action is required.

Error Message     CDP-6-NEIGHBOR_ADDED: Device [chars] discovered of type [chars] with 
port [chars] on incoming port [chars] with ip addr [chars] and mgmt ip [chars]

Explanation    The system discovered a neighbor device.

Recommended Action    No action is required.

Error Message     CDP-6-NEIGHBOR_REMOVED: CDP Neighbor [chars] on port [chars] has been 
removed 

Explanation    The system deleted a neighbor device.

Recommended Action    No action is required.

Error Message     CDP-6-PORTDISABLE: CDP disabled on port [chars] 

Explanation    CDP was disabled on a given port. [chars] is the interface-ID string that identifies the port.

Recommended Action    No action is required.

Error Message     CDP-6-PORTDOWN: A CDP enabled port [chars] went down. 

Explanation    A CDP enabled port became unoperational. [chars] is the interface-ID string that identifies the port.

Recommended Action    No action is required.

Error Message     CDP-6-PORTENABLE: CDP enabled on port [chars] 

Explanation    CDP was enabled on a given port. [chars] is the interface-ID string that identifies the port.

Recommended Action    No action is required.

Error Message     CDP-6-PORTUP: A CDP enabled port [chars] came up. 

Explanation    A CDP enabled port became operational. [chars] is the interface-ID string that identifies the port.

Recommended Action    No action is required.

CDPD Messages

This section contains the CDPD messages.

CDPD-2

Error Message     CDPD-2-INITFAIL Format: CDP Daemon Initialization failed: %s 

Explanation    CDP daemon initialization failed. [chars] explains the reason for the failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CDPD-3

Error Message     CDPD-3-ALLOCFAIL Format: Heap Memory allocation failed: %s 

Explanation    The CDP daemon is out of dynamic memory. [chars] specifies the context where the failure occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CDPD-3-GENERROR Format: %s 

Explanation    The CDP daemon encountered a generalerror thatdoes not fall in any of the above categories. [chars] describes the error and its context.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CDPD-3-MCASTBINDFAIL Format: Failed to bind for CDP multicast address 
on interface 0x%x - %s 

Explanation    An attempt to register for packets destined to the CDP multicast address failed. [dec] identifies the interface and [char] identifies the reason.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CDPD-3-MTSERROR Format: %s 

Explanation    The CDP daemon encountered an MTS error. [chars] specifies the context where the error occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CDPD-3-PKTRECVFAIL Format: Failed to receive packet - %s 

Explanation    The system has failed to receive the packet. [char] identifies the reason.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CDPD-3-PKTSENDFAIL Format: Failed to send packet 

Explanation    The system has failed to send the packet. [dec] identifies the interface and [char] identifies the reason.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CDPD-3-PSSERROR Format: %s 

Explanation    The CDP daemon encountered a PSS error. [chars] specifies the context where the failure occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CDPD-3-SOCKBINDFAIL Format: Failed to bind to raw socket 

Explanation    The system has failed to bind to a raw socket. [dec] identifies the interface and [char] identifies the reason.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CDPD-3-SOCKOPENFAIL Format: Failed to open socket for receiving raw 
802_2 packets - %s 

Explanation    An attempt to open a socket for receiving raw 802_2 packets failed. [char] identifies the reason.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CDPD-4

Error Message     CDPD-4-DUPLEX_MISMATCH Format: Duplex mismatch discovered on %s 

Explanation    duplex mismatch discovered from the received CDP packet.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CDPD-5

Error Message     CDPD-5-DISABLED Format: CDP is disabled 

Explanation    CDP is disabled on the device.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CDPD-5-ENABLED Format: CDP is enabled 

Explanation    CDP is enabled on the device.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CDPD-6

Error Message     CDPD-6-CDPDUP Format: CDP Daemon Up. 

Explanation    The CDP daemon was created successfully and is up and running.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CDPD-6-CDPEXIT Format: CDP Daemon shutting down gracefully. 

Explanation    The CDP daemon is shutting down gracefully.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CDPD-6-NEIGHBOR_ADDED Format: Device %s discovered of type %s with 
port %s on incoming port %s with ip addr %s and mgmt ip %s 

Explanation    The system discovered a neighbor device.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CDPD-6-NEIGHBOR_REMOVED Format: CDP Neighbor %s on port %s has been 
removed 

Explanation    The system deleted a neighbor device.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CDPD-6-PORTDISABLE Format: CDP disabled on port %s 

Explanation    CDP was disabled on a given port. [chars] is the interface-ID string that identifies the port.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CDPD-6-PORTDOWN Format: A CDP enabled port %s went down. 

Explanation    A CDP enabled port became unoperational. [chars] is the interface-ID string that identifies the port.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CDPD-6-PORTENABLE Format: CDP enabled on port %s 

Explanation    CDP was enabled on a given port. [chars] is the interface-ID string that identifies the port.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CDPD-6-PORTUP Format: A CDP enabled port %s came up. 

Explanation    A CDP enabled port became operational. [chars] is the interface-ID string that identifies the port.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CERT_EN Messages

This section contains the CERT_EN messages.

CERT_EN-2

Error Message     CERT_EN-2-PROGRAM_EXIT Format: cert_enroll daemon exiting: %s\n 

Explanation    cert_enroll daemon is exiting.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CERT_EN-3

Error Message     CERT_EN-3-ERROR_MESSAGE Format: %s 

Explanation    This message indicates that a CERT_ENROLL error has occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CERT_EN-3-FIPS_MODE_INIT_ERROR Format: Could not initialize FIPS mode 
: %s 

Explanation    This message indicates that a FIPS mode error has occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CERT_EN-6

Error Message     CERT_EN-6-MESSAGE Format: %s 

Explanation    This message indicates that a CERT_ENROLL error has occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CERT_ENROLL Messages

This section contains the CERT_ENROLL messages.

CERT_ENROLL-2

Error Message     CERT_ENROLL-2-CERT_EN_PROGRAM_EXIT: cert_enroll daemon exiting: 
[chars] 

Explanation    The CERT_ENROLL daemon is exiting.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CERT_ENROLL-3

Error Message     CERT_ENROLL-3-CERT_EN_ERROR_MESSAGE: [chars] 

Explanation    This message indicates that a CERT_ENROLL error has occurred.

Recommended Action    No action is required.

Error Message     CERT_ENROLL-3-CERT_EN_FIPS_MODE_INIT_ERROR: Could not initialize FIPS 
mode : [chars] 

Explanation    This message indicates that a FIPS mode error has occurred.

Recommended Action    No action is required.

CERT_ENROLL-6

Error Message     CERT_ENROLL-6-CERT_EN_MESSAGE: [chars] 

Explanation    This message indicates that a CERT_ENROLL error has occurred.

Recommended Action    No action is required.

CFS Messages

This section contains the CFS messages.

CFS-2

Error Message     CFS-2-CFS_REJECT: CFS reject: [chars]: Switch WWN [chars], ip [chars], 
reason [chars] 

Explanation    This message indicates that the CFS process was rejected: [chars] Switch WWN [chars], ip [chars], reason [chars].

Recommended Action    No action is required.

Error Message     CFS-2-EXITING: Exit reason: [chars] 

Explanation    The CFS service process has exited due to [char]. The process has probably been restarted automatically.

Recommended Action    No action is required.

Error Message     CFS-2-GENERAL_ERROR: [chars] 

Explanation    The CFS service has encountered a critical error. The description of the error is [str.].

Recommended Action    No action is required.

Error Message     CFS-2-INITFAIL Format: CFS Service Init failed: %s 

Explanation    CFS Service initialization failed. [chars] explains the reason for the failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-2-INITFAIL: CFS Service Init failed: [chars] 

Explanation    CFS Service initialization failed. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message     CFS-2-LOCK_FAILED Format: lock failed for sap %d due to internal 
error. 

Explanation    Lock failed due to Unrestricted uncoordinated count is out of synchronizationfor sap [dec].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-2-LOCK_FAILED: lock failed for sap [dec] due to internal error. 

Explanation    Lock failed due to Unrestricted uncoordinated count is out of synchronizationfor sap [dec].

Recommended Action    To recover from this state run command 'cfs internal decrement-unrestricted <app-sap>'.

Error Message     CFS-2-MALLOC_ERROR Format: Size %d bytes 

Explanation    The CFS service could not allocate enough memory.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-2-MALLOC_ERROR: Size [dec] bytes 

Explanation    The CFS service could not allocate enough memory.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-2-MTS_REJECT Format: Verification failed reject MTS message SAP 
%d:RR-token 0x%x 

Explanation    This MTS message could have been posted by the previous active running pre 3.x; MTS structure has changed since then therefore ignore the MTS message, Source SAP [dec]; RR-token [hex].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-2-MTS_REJECT: Verification failed reject MTS message SAP 
[dec]:RR-token [hex] 

Explanation    This MTS message could have been posted by the previous active running pre 3.x; MTS structure has changed since then therefore ignore the MTS message, Source SAP [dec]; RR-token [hex].

Recommended Action    No action is required.

Error Message     CFS-2-PSS_ERROR Format: %s: PSS ret. val=%d 

Explanation    The CFS service encountered an error while operating on a persistent storage database.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-2-PSS_ERROR: [chars]: PSS ret. val=[dec] 

Explanation    The CFS service encountered an error while operating on a persistent storage database.

Recommended Action    No action is required.

Error Message     CFS-2-REJECT Format: CFS reject: %s: Switch WWN %s 

Explanation    This message indicates that the CFS process was rejected: [chars] Switch WWN [chars], ip [chars], reason [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-2-VDC_MGR_FAIL Format: Failed to get a valid switch mac from VDC 
Manager: %s 

Explanation    VDC manager did not respond with a proper MAC address. It could have been because of a timeout in MTS received.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-2-VDC_MGR_FAIL: Failed to get a valid switch mac from VDC Manager: 
[chars] 

Explanation    VDC manager did not respond with a proper MAC address. It could have been because of a timeout in MTS received.

Recommended Action    No action is required.

CFS-3

Error Message     CFS-3-ALLOCFAIL Format: Heap Memory allocation failed: %s 

Explanation    CFS Service is out of dynamic memory. [chars] specifies the context where the failure occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-3-ALLOCFAIL: Heap Memory allocation failed: [chars] 

Explanation    CFS Service is out of dynamic memory. [chars] specifies the context where the failure occurred.

Recommended Action    No action is required.

Error Message     CFS-3-APP_MERGE_FAILED: Merge failed for app [chars], local switch 
wwn [chars], remote switch wwn [chars].Please check 'show cfs merge status name 
[chars]' for more information

Explanation    The CFS service has detected a merge failure.

Recommended Action    No action is required.

Error Message     CFS-3-CFS_PSS_CORRUPTED: [chars] PSS found corrupted 

Explanation    The CFS service has detected a corrupted file in its persistent information databases The database would be recreated.

Recommended Action    No action is required.

Error Message     CFS-3-DBERROR Format: %s 

Explanation    CFS Service encountered a database error. [chars] specifies the context where the failure occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-3-DBERROR: [chars] 

Explanation    CFS Service encountered a database error. [chars] specifies the context where the failure occurred.

Recommended Action    No action is required.

Error Message     CFS-3-FAILURE_RESPONSE Format: %s 0x%x 

Explanation    CFS Service failed to get response [chars][hex] specify the context where the failure occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-3-FAILURE_RESPONSE: [chars] [hex] 

Explanation    CFS Service failed to get response [chars][hex] specify the context where the failure occurred.

Recommended Action    No action is required.

Error Message     CFS-3-FIPS_TEST_FAILED Format: FIPS compliance test failed 

Explanation    FIPS compliance test failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-3-FIPS_TEST_FAILED: FIPS compliance test failed 

Explanation    FIPS compliance test failed.

Recommended Action    No action is required.

Error Message     CFS-3-GENERROR Format: %s 

Explanation    CFS Service encountered a generalerror thatdoes not fall in any of the above categories. [chars] describes the error and its context.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-3-GENERROR: [chars] 

Explanation    CFS Service encountered a generalerror thatdoes not fall in any of the above categories. [chars] describes the error and its context.

Recommended Action    No action is required.

Error Message     CFS-3-LICERR Format: %s 

Explanation    CFS Service failed to get license.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-3-LICERR: [chars] 

Explanation    CFS Service failed to get license.

Recommended Action    No action is required.

Error Message     CFS-3-MERGE_FAILED: Merge failed for app [chars], local switch wwn 
[chars],ip [chars], remote switch wwn [chars], ip [chars]

Explanation    The CFS service has detected a merge failure.

Recommended Action    No action is required.

Error Message     CFS-3-MTSERROR Format: %s 

Explanation    CFS Service encountered an MTS error. [chars] specifies the context where the error occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-3-MTSERROR: [chars] 

Explanation    CFS Service encountered an MTS error. [chars] specifies the context where the error occurred.

Recommended Action    No action is required.

Error Message     CFS-3-PSSERROR Format: %s 

Explanation    CFS Service encountered a PSS error. [chars] specifies the context where the failure occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-3-PSSERROR: [chars] 

Explanation    CFS Service encountered a PSS error. [chars] specifies the context where the failure occurred.

Recommended Action    No action is required.

Error Message     CFS-3-TIMEOUT_ERROR Format: %s 0x%x 

Explanation    CFS Service encountered a timeout [chars][hex] specify the context where the failure occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-3-TIMEOUT_ERROR: [chars] [hex] 

Explanation    CFS Service encountered a timeout [chars][hex] specify the context where the failure occurred.

Recommended Action    No action is required.

Error Message     CFS-3-UNKNOWN_MSG Format: Recvd. from Node=%d SAP=%d 

Explanation    The CFS service has received an unknown message from [dec]].[dec]. This information is for debugging only.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-3-UNKNOWN_MSG: Recvd. from Node=[dec] SAP=[dec] 

Explanation    The CFS service has received an unknown message from [dec]].[dec]. This information is for debugging only.

Recommended Action    No action is required.

CFS-4

Error Message     CFS-4-LICEXP Format: %s 

Explanation    CFS Service license is going to expire. [chars] gives the expected time of expiry.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-4-LICEXP: [chars] 

Explanation    CFS Service license is going to expire. [chars] gives the expected time of expiry.

Recommended Action    No action is required.

Error Message     CFS-4-PSS_VERSION_MISMATCH Format: PSS %d Code %d 

Explanation    There was a version mismatch between the CFS service and one of its persistent storage databases. The persistent information has been translated to the new format.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-4-PSS_VERSION_MISMATCH: PSS [dec] Code [dec] 

Explanation    There was a version mismatch between the CFS service and one of its persistent storage databases. The persistent information has been translated to the new format.

Recommended Action    No action is required.

CFS-6

Error Message     CFS-6-BECAME_ACTIVE Format: Became ACTIVE from standby mode 

Explanation    The CFS service on the standby supervisor became active and it is ready to serve client requests.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-6-BECAME_ACTIVE: Became ACTIVE from standby mode 

Explanation    The CFS service on the standby supervisor became active and it is ready to serve client requests.

Recommended Action    No action is required.

Error Message     CFS-6-BECAME_STDBY Format: Became STANDBY from active mode 

Explanation    The CFS service became standby from active mode.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-6-BECAME_STDBY: Became STANDBY from active mode 

Explanation    The CFS service became standby from active mode.

Recommended Action    No action is required.

Error Message     CFS-6-EXCESSIVE_DELAY: [chars] 

Explanation    Excessive time taken for a processing event. The description of the event is [str.].

Recommended Action    No action is required.

Error Message     CFS-6-FAILED_TO_SEND_HEARTBEAT Format: Failed to send heartbeat to 
system manager: Reason=%s 

Explanation    The CFS service was unable to send heartbeats to the system manager.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-6-FAILED_TO_SEND_HEARTBEAT: Failed to send heartbeat to system 
manager: Reason=[chars] 

Explanation    The CFS service was unable to send heartbeats to the system manager.

Recommended Action    No action is required.

Error Message     CFS-6-GENERAL_EVENT: [chars] 

Explanation    The CFS service has generated an important event. The description of the event is [str.].

Recommended Action    No action is required.

Error Message     CFS-6-INVALID_CHECKSUM: Received packet from peer on if-index([hex]) 
with corrupted checksum 

Explanation    This could be because of the errors in the link.

Recommended Action    No action is required.

Error Message     CFS-6-INVALID_IF_INDEX: Received packet on if-index([hex]) which is 
not recognized by CFS 

Explanation    The if-index does not match with the if-index used in discovery orthe systemmight have already received an adjacency cleanup message for this if-index. Check if the if-index is that of the port channel or a physical if-index.

Recommended Action    No action is required.

Error Message     CFS-6-LOGICAL_DISTRIBUTION_INFO Format: vsan %d 

Explanation    VSAN [dec], source wwn [chars], ip [chars], app-id [dec], user [chars], event [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-6-LOGICAL_DISTRIBUTION_INFO: vsan [dec], source wwn [chars], ip 
[chars] app-id [dec], session-id [dec], user [chars], [chars] 

Explanation    VSAN [dec], source wwn [chars], ip [chars], app-id [dec], user [chars], event [chars].

Recommended Action    No action is required.

Error Message     CFS-6-PHY_DISTRIBUTION_INFO Format: source wwn %s 

Explanation    source wwn [chars], ip [chars], app-id [dec], session-id [dec], user [chars], event [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-6-PHY_DISTRIBUTION_INFO: source wwn [chars], ip [chars], app-id 
[dec], session-id [dec], user [chars], [chars] 

Explanation    Source wwn [chars], ip [chars], app-id [dec], session-id [dec], user [chars], event [chars].

Recommended Action    No action is required.

Error Message     CFS-6-PSS_CREATED: [chars] PSS Created 

Explanation    One of the persistent information database of CFS service has been recreated.

Recommended Action    No action is required.

Error Message     CFS-6-PSS_DESTROYED: [chars] PSS Destroyed 

Explanation    One of the persistent information databases of CFS Service has been intentionally destroyed and would be recreated.

Recommended Action    No action is required.

Error Message     CFS-6-REGION_CTX_REMOVED Format: Region info is deleted for %s 

Explanation    [chars] is in logical scope. Regions support only physical scope applications.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-6-REGION_CTX_REMOVED: Region info is deleted for [chars] 

Explanation    [chars] is in logical scope. Regions support only physical scope applications.

Recommended Action    No action is required.

Error Message     CFS-6-SERVICE_UP: Initialized [chars] 

Explanation    The CFS service is up and ready to accept client requests The service was initialized in [char] mode.

Recommended Action    No action is required.

Error Message     CFS-6-SRVCREATED Format: CFS Service created 

Explanation    CFS Service was created successfully and is up and running.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-6-SRVCREATED: CFS Service created 

Explanation    CFS Service was created successfully and is up and running.

Recommended Action    No action is required.

Error Message     CFS-6-SRVEXIT Format: CFS Service shutting down gracefully 

Explanation    CFS Service is shutting down gracefully.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-6-SRVEXIT: CFS Service shutting down gracefully 

Explanation    CFS Service is shutting down gracefully.

Recommended Action    No action is required.

Error Message     CFS-6-SWITCHOVER Format: Switching Over to other Sup. 

Explanation    The CFS service has successfully switched over to the standby supervisor module.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CFS-6-SWITCHOVER: Switching Over to other Sup. 

Explanation    The CFS service has successfully switched over to the standby supervisor module.

Recommended Action    No action is required.

CIM Messages

This section contains the CIM messages.

CIM-2

Error Message     CIM-2-SYSLOG_EXIT Format: Message:%s errcode:%d 

Explanation    exit due to critical error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CIM-2-SYSLOG_PSS_SNAPSHOT_ERR Format: Source URI:%s Destination 
URI:%s errcode:%d 

Explanation    PSS snapshot error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CIM-2-SYSLOG_SDWRAP_ERR Format: Description:%s errcode:%d 

Explanation    Debug infrastructure error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CIM-3

Error Message     CIM-3-SYSLOG_COPY_CONFIG_ERR Format: Message:%s URI:%s errcode:%d 

Explanation    copy running startup error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CIM-3-SYSLOG_FILE_ERR Format: Purpose:%s Filename:%s errcode:%d 

Explanation    File handling error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CIM-3-SYSLOG_MTS_ERR Format: message %s 

Explanation    MTS message handling error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CIM-3-SYSLOG_PSS_ERR Format: Purpose:%s URI:%s errcode:%d 

Explanation    PSS handling error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CIM-6

Error Message     CIM-6-LOG_CIM_CERTIFICATE_CLEARED Format: Cleared certificate %s 

Explanation    Cleared a certificate named [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CIM-6-LOG_CIM_CERTIFICATE_INSTALLED Format: Installed certificate %s 

Explanation    Installed a certificate named [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CIMSRVPROV Messages

This section contains the CIMSRVPROV messages.

CIMSRVPROV-2

Error Message     CIMSRVPROV-2-CIM_SYSLOG_EXIT: Message:[chars] errcode:[dec] 

Explanation    Exit due to critical error.

Recommended Action    No action is required.

Error Message     CIMSRVPROV-2-CIM_SYSLOG_PSS_SNAPSHOT_ERR: Source URI:[chars] 
Destination URI:[chars] errcode:[dec] 

Explanation    PSS snapshot error.

Recommended Action    No action is required.

Error Message     CIMSRVPROV-2-CIM_SYSLOG_SDWRAP_ERR: Description:[chars] 
errcode:[dec] 

Explanation    Debug infrastructure error.

Recommended Action    No action is required.

CIMSRVPROV-3

Error Message     CIMSRVPROV-3-CIM_SYSLOG_COPY_CONFIG_ERR: Message:[chars] URI:[chars] 
errcode:[dec] 

Explanation    Copy running startup error.

Recommended Action    No action is required.

Error Message     CIMSRVPROV-3-CIM_SYSLOG_FILE_ERR: Purpose:[chars] Filename:[chars] 
errcode:[dec] 

Explanation    File handling error.

Recommended Action    No action is required.

Error Message     CIMSRVPROV-3-CIM_SYSLOG_MTS_ERR: message [chars] 

Explanation    MTS message handling error.

Recommended Action    No action is required.

Error Message     CIMSRVPROV-3-CIM_SYSLOG_PSS_ERR: Purpose:[chars] URI:[chars] 
errcode:[dec] 

Explanation    PSS handling error.

Recommended Action    No action is required.

CIMSRVPROV-6

Error Message     CIMSRVPROV-6-LOG_CIM_CERTIFICATE_CLEARED: Cleared certificate 
[chars] 

Explanation    Cleared a certificate named [chars].

Recommended Action    No action is required.

Error Message     CIMSRVPROV-6-LOG_CIM_CERTIFICATE_INSTALLED: Installed certificate 
[chars] 

Explanation    Installed a certificate named [chars].

Recommended Action    No action is required.

CLIS Messages

This section contains the CLIS messages.

CLIS-5

Error Message     CLIS-5-CLIS_SYSLOG_CMD_REMOVED: Command deleted from the NVDB: 
[chars] 

Explanation    Command removal due to configuration change.

Recommended Action    No action is required.

Error Message     CLIS-5-SYSLOG_CMD_REMOVED Format: Command deleted from the NVDB: %s 

Explanation    Command removal due to configuration change.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CLK_MGR Messages

This section contains the CLK_MGR messages.

CLK_MGR-5

Error Message     CLK_MGR-5-CLI_CONFIG Format: CLK_MGR clock is synchronized by %s from 
VDC %d 

Explanation    CLK_MGR clock is synchronized by [chars] from VDC.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CLOUD Messages

This section contains the CLOUD messages.

CLOUD-2

Error Message     CLOUD-2-PROGRAM_EXIT Format: cloud-discovery process ending: %s\n 

Explanation    cloud-discovery process is exiting with the reason [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLOUD-2-PROGRAM_EXIT: cloud-discovery process ending: [chars] 

Explanation    Cloud-discovery process is exiting with the reason [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CLOUD-3

Error Message     CLOUD-3-CFS_MERGE_OPERATION_FAILED Format: %s 

Explanation    [chars1].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLOUD-3-CFS_OPERATION_FAILED Format: %s : %s 

Explanation    [chars1] [chars2].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLOUD-3-CLOUD_CFS_MERGE_OPERATION_FAILED: [chars] 

Explanation    [chars1].

Recommended Action    Check the reason for the failure of the CFS operation and fix the problem.

Error Message     CLOUD-3-CLOUD_CFS_OPERATION_FAILED: [chars] : [chars] 

Explanation    [chars1] [chars2].

Recommended Action    Check the reason for the failure of the CFS operation and fix the problem.

Error Message     CLOUD-3-CLOUD_FEATURE_MANAGER_ERROR: [chars] : [chars] 

Explanation    [chars1] [chars2].

Recommended Action    Check the reason for error using feature manager and fix the problem.

Error Message     CLOUD-3-CLOUD_PSS_OPERATION_FAILED: [chars] : [chars] 

Explanation    [chars1] [chars2].

Recommended Action    Check the reason for the failure of the pss operation and fix the problem.

Error Message     CLOUD-3-FEATURE_MANAGER_ERROR Format: %s : %s 

Explanation    [chars1] [chars2].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLOUD-3-PSS_OPERATION_FAILED Format: %s : %s 

Explanation    [chars1] [chars2].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CLOUD-6

Error Message     CLOUD-6-CLOUD_DISCOVERY_DONE: discovery over 

Explanation    Cloud-discovery started.

Recommended Action    Check cloud membership.

Error Message     CLOUD-6-CLOUD_DISCOVERY_STARTED: [chars] discovery started 

Explanation    Cloud-discovery started.

Recommended Action    Check cloud-discovery status after sometime.

Error Message     CLOUD-6-DISCOVERY_DONE Format: discovery over\n 

Explanation    cloud-discovery started.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLOUD-6-DISCOVERY_STARTED Format: %s discovery started\n 

Explanation    cloud-discovery started.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CLP_XBAR Messages

This section contains the CLP_XBAR messages.

CLP_XBAR-2

Error Message     CLP_XBAR-2-FR_CRC Format: %s 

Explanation    Clipper received packets with CRC error from fabric.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CLUSTER Messages

This section contains the CLUSTER messages.

CLUSTER-2

Error Message     CLUSTER-2-ADD_FAIL Format: Cluster 0x%llx creation failed\n 

Explanation    Cluster Creation Failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-2-CAP_ADD_FAIL Format: Failed to add cluster capability %d 

Explanation    Cluster capability addition failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-2-CAP_DEL_FAIL Format: Failed to delete cluster capability %d 

Explanation    Cluster capability deletion failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-2-CLUSTER_CAP_ADD_FAIL: Failed to add cluster capability 
[dec] 

Explanation    Cluster capability addition failed.

Recommended Action    No action is required.

Error Message     CLUSTER-2-CLUSTER_CAP_DEL_FAIL: Failed to delete cluster capability 
[dec] 

Explanation    Cluster capability deletion failed.

Recommended Action    No action is required.

Error Message     CLUSTER-2-DB_SYNC_FAIL Format: Cluster 0x%llx application %d dataset 
%d database synchronization failed 

Explanation    Cluster database synchronization failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-2-DB_SYNC_FAIL_CLIENT Format: Client on node 0x%llx for 
cluster 0x%llx application %d dataset %d received database synchronization failed 

Explanation    Cluster database synchronization failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-2-DB_SYNC_FAIL_MANAGER Format: Manager on node 0x%llx for 
cluster 0x%llx application %d dataset %d received database synchronization failed 

Explanation    Cluster database synchronization failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-2-DB_SYNC_FAIL_SERVER Format: Server on node 0x%llx for 
cluster 0x%llx application %d dataset %d received database synchronization failed 

Explanation    Cluster database synchronization failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-2-LEADER_ANNOUNCE Format: Node 0x%llx is the new Master of 
cluster 0x%llx of %d nodes\n 

Explanation    Leader announcement of cluster.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-2-LEAVE_REQ_FAIL Format: Node failed to send LEAVE request to 
Cluster 0x%llx\n 

Explanation    Failed to send Leave Request.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-2-LEAVE_RESP_FAIL Format: Bad response to LEAVE request for 
Cluster 0x%llx\n 

Explanation    Received Bad Leave response.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-2-LOCAL_NODE_EXIT Format: Local Node 0x%llx has left the 
Cluster 0x%llx\n 

Explanation    Node is not part of cluster.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-2-QUORUM_GAIN Format: Cluster 0x%llx now has quorum with %d 
nodes\n 

Explanation    Cluster has quorum.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-2-QUORUM_LOSS Format: Cluster 0x%llx has lost quorum; number 
of nodes=%d\n 

Explanation    Cluster has lost quorum.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-2-RGC_TRANSACTION_FAIL Format: Cluster 0x%llx RGC transaction 
application=%d dataset=%d failed reason=%s 

Explanation    Cluster RGC transaction failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-2-TRANSPORT_FAIL Format: Cluster 0x%llx transport failed to 
send message from node 0x%llx to 0x%llx error=%d\n 

Explanation    Cluster transport failed to send message.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CLUSTER-5

Error Message     CLUSTER-5-ADD Format: Cluster 0x%llx added\n 

Explanation    Cluster Added.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-5-DISABLED Format: CLUSTER Disabled 

Explanation    CLUSTER Service Disabled.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-5-ENABLED Format: CLUSTER Enabled 

Explanation    CLUSTER Service Enabled.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-5-NODE_ADD Format: Node 0x%llx added to cluster 0x%llx\n 

Explanation    Node added to cluster.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-5-NODE_JOIN Format: Node 0x%llx joined cluster 0x%llx\n 

Explanation    Node joined cluster.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-5-NODE_LEAVE Format: Node 0x%llx not in cluster 0x%llx\n 

Explanation    Node not in cluster.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-5-NODE_LEAVE_EXPLICIT Format: Remote Node 0x%llx has left the 
Cluster 0x%llx voluntarily\n 

Explanation    Remote Node Left voLUNtarily.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-5-NODE_REMOVE Format: Node 0x%llx removed from cluster 
0x%llx\n 

Explanation    Node removed from cluster.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-5-REMOVE Format: Cluster 0x%llx removed\n 

Explanation    Cluster removed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-5-RX_JOIN_REQ Format: Node 0x%llx received JOIN request from 
node=0x%llx 

Explanation    Cluster received JOIN request.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-5-RX_JOIN_RESP Format: Node 0x%llx received JOIN response 
from node=0x%llx result=%s 

Explanation    Cluster received JOIN response.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-5-RX_PROBE Format: Node 0x%llx received PROBE from 
node=0x%llx 

Explanation    Cluster received PROBE message.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-5-STARTED Format: CLUSTER 0x%llx Started 

Explanation    CLUSTER Started.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-5-STOPPED Format: CLUSTER 0x%llx Stopped 

Explanation    CLUSTER Stopped.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-5-TRANSPORT_DOWN Format: Cluster 0x%llx transport down for 
node=0x%llx 

Explanation    Cluster Transport Connection DOWN.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-5-TRANSPORT_UP Format: Cluster 0x%llx transport up for 
node=0x%llx 

Explanation    Cluster Transport Connection UP.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-5-TX_JOIN_REQ Format: Node 0x%llx sending JOIN request to 
node=0x%llx 

Explanation    Cluster sending JOIN request.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER-5-TX_JOIN_RESP Format: Node 0x%llx sending JOIN response to 
node=0x%llx result=%s 

Explanation    Cluster sending JOIN request.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CLUSTER_TEST_APP Messages

This section contains the CLUSTER_TEST_APP messages.

CLUSTER_TEST_APP-5

Error Message     CLUSTER_TEST_APP-5-DISABLED Format: CLUSTER_TEST_APP Disabled 

Explanation    CLUSTER_TEST_APP Service Disabled.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER_TEST_APP-5-ENABLED Format: CLUSTER_TEST_APP Enabled 

Explanation    CLUSTER_TEST_APP Service nabled.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER_TEST_APP-5-TEST_STARTED Format: Traffic test started 

Explanation    CLUSTER_TEST_APP Test started.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CLUSTER_TEST_APP-5-TEST_STOPPED Format: Traffic test stopped 

Explanation    CLUSTER_TEST_APP Test stopped.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CMOND Messages

This section contains the CMOND messages.

CMOND-2

Error Message     CMOND-2-CMOND_ALERT_MSG: [chars] 

Explanation    Alert message.

Recommended Action    No action is required.

Error Message     CMOND-2-CMOND_ERROR_MSG: [chars] 

Explanation    Error message.

Recommended Action    No action is required.

CMPPROXY Messages

This section contains the CMPPROXY messages.

CMPPROXY-2

Error Message     CMPPROXY-2-LOG_CMP_IS_NOT_UP: Connectivity Management processor (on 
module [dec]) did not come up 

Explanation    Connectivity Management processor is not sending heartbeats on this module.

Recommended Action    No action is required.

Error Message     CMPPROXY-2-LOG_CMP_UP: Connectivity Management processor(on module 
[dec]) is now UP 

Explanation    Connectivity Management processor has come up and is exchanging heartbeats with CP on this supervisor slot.

Recommended Action    No action is required.

Error Message     CMPPROXY-2-LOG_CMP_WENT_DOWN: Connectivity Management processor (on 
module [dec]) went DOWN 

Explanation    Connectivity Management processor has either gone down or is not sending heartbeats for a long time.

Recommended Action    No action is required.

CMPPROXY-5

Error Message     CMPPROXY-5-LOG_CMP_AAA_FAILURE: Authentication failed for a login 
from CMP (on module [dec]) 

Explanation    A login attempt has been denied access from Connectivity management processor (CMP) as authentication did not succeed.

Recommended Action    No action is required.

Error Message     CMPPROXY-5-MALLOC_FAILURE Format: Memory allocation failure 

Explanation    Memory allocation in a call to malloc/calloc has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CMPPROXY-5-MALLOC_FAILURE: Memory allocation failure 

Explanation    Memory allocation in a call to malloc/calloc has failed.

Recommended Action    No action is required.

CMPPROXY-6

Error Message     CMPPROXY-6-LOG_CMP_AAA_SUCCESS: Authentication succeeded for a login 
from CMP (on module [dec]) 

Explanation    A login attempt has succeeded from Connectivity management processor (CMP) in getting access as AAA succeeded.

Recommended Action    No action is required.

CMTMDL Messages

This section contains the CMTMDL messages.

CMTMDL-2

Error Message     CMTMDL-2-DB_UNLOCK_FAILED Format: Failed to unlock the database for 
session:%s 

Explanation    Session-Manager failed to unlock the database for session: [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CMTMDL-3

Error Message     CMTMDL-3-ALLOC_FAILED Format: Failed in File:%s Line:%d for type %d 
size %d 

Explanation    SDM process could not allocate heap memory in File:[chars], at line:[dec], for memory-type:[dec] of Size:[dec].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

COPP Messages

This section contains the COPP messages.

COPP-1

Error Message     COPP-1-COPP_DROPS1: CoPP drops exceed threshold in class: [chars], 
check show policy-map interface control-plane for more info. 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    No action is required.

Error Message     COPP-1-DROPS1 Format: CoPP drops exceed threshold in class: %s 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

COPP-2

Error Message     COPP-2-COPP_DROPS2: CoPP drops exceed threshold in class: [chars], 
check show policy-map interface control-plane for more info. 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    No action is required.

Error Message     COPP-2-COPP_INIT_FAIL: CoPP Initialization failed: [chars] 

Explanation    CoPP Initialization failed. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message     COPP-2-COPP_MTS_FAIL: Failed to do MTS operation: [chars] 

Explanation    The system has failed to do an MTS operation. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message     COPP-2-COPP_NO_PINST: Control-plane is unprotected. 

Explanation    There isn't any policy configured to protect control-plane.

Recommended Action    No action is required.

Error Message     COPP-2-DROPS2 Format: CoPP drops exceed threshold in class: %s 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     COPP-2-INIT_FAIL Format: CoPP Initialization failed: %s 

Explanation    CoPP Initialization failed. [chars] explains the reason for the failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     COPP-2-MTS_FAIL Format: Failed to do MTS operation: %s 

Explanation    The system has failed to do an MTS operation. [chars] explains the reason for the failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     COPP-2-NO_PINST Format: Control-plane is unprotected. 

Explanation    There isn't any policy configured to protect control-plane.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

COPP-3

Error Message     COPP-3-ALLOC_FAIL Format: Memory allocation failure: %s 

Explanation    Failed to allocate required memory. [chars] explains the reason for the failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     COPP-3-COPP_ALLOC_FAIL: Memory allocation failure: [chars] 

Explanation    Failed to allocate required memory. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message     COPP-3-COPP_DROPS3: CoPP drops exceed threshold in class: [chars], 
check show policy-map interface control-plane for more info. 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    No action is required.

Error Message     COPP-3-COPP_PPF_FAIL: Error during PPF operation: [chars] 

Explanation    The system has failed to do a PPF operation. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message     COPP-3-COPP_PSS_FAIL: Error during PSS operation: [chars] 

Explanation    The system has failed to do a PSS operation. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message     COPP-3-DROPS3 Format: CoPP drops exceed threshold in class: %s 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     COPP-3-PPF_FAIL Format: Error during PPF operation: %s 

Explanation    The system has failed to do a PPF operation. [chars] explains the reason for the failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     COPP-3-PSS_FAIL Format: Error during PSS operation: %s 

Explanation    The system has failed to do a PSS operation. [chars] explains the reason for the failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

COPP-4

Error Message     COPP-4-COPP_DROPS4: CoPP drops exceed threshold in class: [chars], 
check show policy-map interface control-plane for more info. 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    No action is required.

Error Message     COPP-4-DROPS4 Format: CoPP drops exceed threshold in class: %s 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

COPP-5

Error Message     COPP-5-COPP_DISABLED: COPP Disabled 

Explanation    COPP Service Disabled.

Recommended Action    No action is required.

Error Message     COPP-5-COPP_DROPS5: CoPP drops exceed threshold in class: [chars], 
check show policy-map interface control-plane for more info. 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    No action is required.

Error Message     COPP-5-COPP_ENABLED: COPP Enabled 

Explanation    COPP Service nabled.

Recommended Action    No action is required.

Error Message     COPP-5-COPP_INIT: COPP initialized 

Explanation    COPP Service Initialized.

Recommended Action    No action is required.

Error Message     COPP-5-DISABLED Format: COPP Disabled 

Explanation    COPP Service Disabled.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     COPP-5-DROPS5 Format: CoPP drops exceed threshold in class: %s 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     COPP-5-ENABLED Format: COPP Enabled 

Explanation    COPP Service nabled.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     COPP-5-INIT Format: COPP initialized 

Explanation    COPP Service Initialized.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

COPP-6

Error Message     COPP-6-COPP_DROPS6: CoPP drops exceed threshold in class: [chars], 
check show policy-map interface control-plane for more info. 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    No action is required.

Error Message     COPP-6-COPP_POLICY_ATTACHED: CoPP policy has been attached to control 
plane interface. 

Explanation    CoPP policy has been attached to control plane interface.

Recommended Action    No action is required.

Error Message     COPP-6-COPP_POLICY_DETACHED: CoPP policy has been detached from 
control plane interface. 

Explanation    CoPP policy has been detached from control plane interface.

Recommended Action    No action is required.

Error Message     COPP-6-DROPS6 Format: CoPP drops exceed threshold in class: %s 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     COPP-6-POLICY_ATTACHED Format: CoPP policy has been attached to 
control plane interface. 

Explanation    CoPP policy has been attached to control plane interface.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     COPP-6-POLICY_DETACHED Format: CoPP policy has been detached from 
control plane interface. 

Explanation    CoPP policy has been detached from control plane interface.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

COPP-7

Error Message     COPP-7-COPP_DROPS7: CoPP drops exceed threshold in class: [chars], 
check show policy-map interface control-plane for more info. 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    No action is required.

Error Message     COPP-7-DROPS7 Format: CoPP drops exceed threshold in class: %s 

Explanation    There are CoPP drops, [chars] tell which class has dropped packets.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CORE-DMON Messages

This section contains the CORE-DMON messages.

CORE-DMON-2

Error Message     CORE-DMON-2-MODULE_COREDUMP_DONE: kernel coredump completed on 
module:[dec] 

Explanation    Kernel coredump finishing on a module.

Recommended Action    No action is required.

Error Message     CORE-DMON-2-MODULE_COREDUMP_STARTED: kernel coredump started on 
module:[dec] 

Explanation    Kernel coredump starting on a module.

Recommended Action    No action is required.

CORE-DMON-3

Error Message     CORE-DMON-3-NO_SPACE: Failed to save core file [chars]. Try removing 
existing core files. 

Explanation    Not enough space to save new core files.

Recommended Action    No action is required.

CORE_DMON Messages

This section contains the CORE_DMON messages.

CORE_DMON-2

Error Message     CORE_DMON-2-MODULE_COREDUMP_DONE Format: kernel coredump completed on 
module:%d\n 

Explanation    kernel coredump finishing on a module.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CORE_DMON-2-MODULE_COREDUMP_STARTED Format: kernel coredump started 
on module:%d\n 

Explanation    kernel coredump starting on a module.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CPPA_MGR Messages

This section contains the CPPA_MGR messages.

CPPA_MGR-3

Error Message     CPPA_MGR-3-ENABLE_VB_FAILURE: Virtual service blade [dec] could not 
be [chars]. Error: [chars] 

Explanation    The requested virtual blade operation could not be completed.

Recommended Action    No action is required.

Error Message     CPPA_MGR-3-NO_HB_REBOOT: No heartbeat from agent service. Nexus1010 
is rebooted 

Explanation    No heartbeat from agent service. Nexus1010 is rebooted.

Recommended Action    No action is required.

Error Message     CPPA_MGR-3-REMOTE_ILO_REBOOT: Remote mgmt feature rebooted other 
Nexus1010 using ILO 

Explanation    Remote mgmt feature rebooted other Nexus1010 using ILO.

Recommended Action    No action is required.

Error Message     CPPA_MGR-3-RESTORE_FAILURE: Agent version could not be restored to 
make versions match 

Explanation    The previous agent version could not be restored. The system needs to be reinstalled to recover.

Recommended Action    No action is required.

Error Message     CPPA_MGR-3-SOME_PNIC_FAILURE: Not all the Nexus1010 physical NICs are 
detected. Check for failure 

Explanation    Not all the physical NICs are detected. Check for failure.

Recommended Action    No action is required.

Error Message     CPPA_MGR-3-UNDO_WRITE_ERASE: Undo Write Erase: [chars] 

Explanation    The software undo write erase result:.

Recommended Action    No action is required.

Error Message     CPPA_MGR-3-UPGRADE_FAILED: Upgrade failed: [chars] 

Explanation    The software upgrade could not complete because of the errors.

Recommended Action    No action is required.

Error Message     CPPA_MGR-3-VERSION_MISMATCH: Agent version mismatch detected. System 
will be reloaded 

Explanation    The cppa_mgr and the underlying agent are not running the same software version.

Recommended Action    No action is required.

Error Message     CPPA_MGR-3-WRITE_ERASE: Write Erase: [chars] 

Explanation    The software write erase result:.

Recommended Action    No action is required.

CPPA_MGR-5

Error Message     CPPA_MGR-5-REMOTE_VB_HA_FAILURE: Operation failed in standby for 
virtual service blade [dec]: [chars] 

Explanation    An error occurred while processing a command from active at standby.

Recommended Action    No action is required.

Error Message     CPPA_MGR-5-REMOTE_VB_IMG_FAILURE: Could not verify image in standby 
for virtual service blade [dec] creation: [chars] 

Explanation    An error occurred while processing image required for vb creation at standby.

Recommended Action    No action is required.

Error Message     CPPA_MGR-5-UPGRADE_COMPLETE: Upgrade completed successfully 

Explanation    The software upgrade completed with no errors.

Recommended Action    No action is required.

Error Message     CPPA_MGR-5-UPGRADE_START: Upgrade started. Image: [chars] 

Explanation    A software upgrade has been initiated by the user.

Recommended Action    No action is required.

Error Message     CPPA_MGR-5-VB_DEPLOYED: Virtual service blade [chars] deployed 

Explanation    Virtual service blade deployed on nexus1010 successfully.

Recommended Action    No action is required.

Error Message     CPPA_MGR-5-VB_REMOVED: Virtual service blade [chars] removed 

Explanation    Virtual service blade removed by user.

Recommended Action    No action is required.

Error Message     CPPA_MGR-5-VB_RESTARTED: Virtual service blade [chars] restarted 

Explanation    Virtual service blade restarted by user.

Recommended Action    No action is required.

Error Message     CPPA_MGR-5-VB_SHUT: Virtual service blade [chars] moved into shut 
state 

Explanation    Virtual service blade shut by user.

Recommended Action    No action is required.

CRDCFG Messages

This section contains the CRDCFG messages.

CRDCFG-2

Error Message     CRDCFG-2-SRV_CRIT Format: %s 

Explanation    CardConfig CRITICAL ERROR.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CRDCFG-3

Error Message     CRDCFG-3-ERR Format: %s 

Explanation    CardConfig error mesage.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CRDCFG-3-MSG Format: %s 

Explanation    CardConfig log mesage.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CRDCFG-3-SRV_ERR Format: %s 

Explanation    CardConfigServer error mesage.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CRDCFG-3-SRV_MSG Format: %s 

Explanation    CardConfigServer log mesage.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CRDCLIENT Messages

This section contains the CRDCLIENT messages.

CRDCLIENT-2

Error Message     CRDCLIENT-2-CARDCL_CRIT Format: %s 

Explanation    CardClient Critical Message.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CRDCLIENT-2-ONL Format: %s 

Explanation    Online Message.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CRDCLIENT-2-REG Format: %s 

Explanation    CardClient Console Message.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CRDCLIENT-2-SSE Format: %s 

Explanation    CardClient Console Message.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CRDCLIENT-3

Error Message     CRDCLIENT-3-CARDCL_ERR Format: %s 

Explanation    CardClient Error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CRDCLIENT-3-CARDCL_INFO Format: %s 

Explanation    CardClient Flow Message.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CREDITMON-SLOT# Messages

This section contains the CREDITMON-SLOT# messages.

CREDITMON-SLOT#-2

Error Message     CREDITMON-SLOT#-2-SYSERR_CREDITMON_APP_EXITED: [chars] 

Explanation    Credit Monitor application exited.

Recommended Action    No action is required.

Error Message     CREDITMON-SLOT#-2-SYSERR_CREDITMON_MTS_INIT_ERR: [chars] 

Explanation    Credit Monitor error binding to MTS.

Recommended Action    No action is required.

CTS Messages

This section contains the CTS messages.

CTS-2

Error Message     CTS-2-CTS_AUTHENT_FAILURE: CTS Authentication failure on Port [chars] 
(CTS Failure Reason: [chars] [chars]) 

Explanation    Fibre-Channel Authentication failure on Port [chars].(Reason Code [chars] Detail [chars]). Check password configurations and ensure appropriate security modes on this port as well as peer port.

Recommended Action    No action is required.

Error Message     CTS-2-CTS_FIPS_BYPASS_TEST_FAILED: FIPS bypass test failed for 
interface: [chars] 

Explanation    The system has detected an error.

Recommended Action    No action is required.

Error Message     CTS-2-CTS_SAP_FAILED: SAP exchange failed on interface [chars]. 
(Reason: [chars]) 

Explanation    The system has detected an error.

Recommended Action    No action is required.

Error Message     CTS-2-CTS_SAP_REKEY_FAILED: SAP exchange failed on interface [chars]. 
(Reason: [chars]) 

Explanation    The system has detected an error.

Recommended Action    No action is required.

Error Message     CTS-2-DBG_INIT_FAILED: Debug Infrastructure Initialization failed ( 
[chars] ) 

Explanation    The system has detected an error.

Recommended Action    No action is required.

Error Message     CTS-2-FC2_E_INIT_FAILED: Fibre-Channel Initialization of an E_Port 
failed ( [chars] ) 

Explanation    CTS Manager has been unable to initialize with the FC-2 E-Port infrastructure.

Recommended Action    No action is required.

Error Message     CTS-2-FC2_F_INIT_FAILED: Fibre-Channel Initialization of an F_Port 
failed ( [chars] ) 

Explanation    CTS Manager has been unable to initialize with the FC-2 F-Port infrastructure.

Recommended Action    No action is required.

Error Message     CTS-2-FC2_UNKNOWN_FRM_RECD_CRIT Format: Received an 
unexpected/unknown FC-2 frame on %s 

Explanation    The system has detected an error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CTS-2-FC2_UNKNOWN_FRM_RECD_CRIT: Received an unexpected/unknown FC-2 
frame on [chars] 

Explanation    The system has detected an error.

Recommended Action    No action is required.

Error Message     CTS-2-FIPS_BYPASS_TEST_FAILED Format: FIPS bypass test failed for 
interface: %s 

Explanation    The system has detected an error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CTS-2-FSMU_INIT_FAILED: State Machine Infrastructure Initialization 
failed ( [chars] ) 

Explanation    The system has detected an error.

Recommended Action    No action is required.

Error Message     CTS-2-IPC_INIT_FAILED: IPC (Inter Process Communication) 
Initialization failed ( [chars] ) 

Explanation    CTS Manager has been unable to initialize with the IPC infrastructure.

Recommended Action    No action is required.

Error Message     CTS-2-LICENSE_UNAVAILABLE Format: License:%s unavailable 

Explanation    License of [chars] is unavailable. Service will exit now.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CTS-2-LICENSE_UNAVAILABLE: License:[chars] unavailable, service 
exiting 

Explanation    License of [chars] is unavailable. Service will exit now.

Recommended Action    Install the license file to continue using the feature.

Error Message     CTS-2-MEM_FAILED Format: Memory operations failed File: %s Line %d 
for size 0x%x bytes 

Explanation    The system has detected an error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CTS-2-MEM_FAILED: Memory operations failed File: [chars] Line [dec] 
for size [hex] bytes 

Explanation    The system has detected an error.

Recommended Action    No action is required.

Error Message     CTS-2-POST_INIT_FAILED: Post-Initialization failed ( [chars] ) 

Explanation    The system has detected an error.

Recommended Action    No action is required.

Error Message     CTS-2-PSS_INIT_FAILED: PSS Infrastructure Initialization failed ( 
[chars] ) 

Explanation    The system has detected an error.

Recommended Action    No action is required.

Error Message     CTS-2-RBACL_ENFORCEMENT_FAILED Format: Failed to %s RBACL enforcement 
on %s %lu 

Explanation    The system has detected an error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CTS-2-RBACL_ENFORCEMENT_FAILED: Failed to [chars] RBACL enforcement 
on [chars] %lu 

Explanation    The system has detected an error.

Recommended Action    No action is required.

Error Message     CTS-2-RBACL_ENFORCEMENT_FAILED: RBACL enforcement failed on [chars] 
[dec] 

Explanation    The system has detected an error.

Recommended Action    No action is required.

Error Message     CTS-2-RBACL_LC_INSERT_FAILED Format: RBACL programming failed for 
inserted module %d 

Explanation    The system has detected an error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CTS-2-RBACL_LC_INSERT_FAILED: RBACL programming failed for inserted 
module [dec] 

Explanation    The system has detected an error.

Recommended Action    No action is required.

Error Message     CTS-2-RBACL_TCAM_SPACE_NOT_ENOUGH Format: Not enough free space left 
on TCAM 

Explanation    The system has detected an error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CTS-2-RBACL_TCAM_SPACE_NOT_ENOUGH: Not enough free space left on TCAM 

Explanation    The system has detected an error.

Recommended Action    No action is required.

Error Message     CTS-2-RBACL_UNABLE_PARSE_ACE Format: Unable to parse RBACL ACE 
substring: %s 

Explanation    The system has detected an error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CTS-2-RBACL_UNABLE_PARSE_ACE: Unable to parse RBACL ACE substring: 
[chars] 

Explanation    The system has detected an error.

Recommended Action    No action is required.

Error Message     CTS-2-RBACL_UPDATE_FAILED Format: Failed to %s RBACL %s 

Explanation    The system has detected an error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CTS-2-RBACL_UPDATE_FAILED: Failed to [chars] RBACL [chars] 

Explanation    The system has detected an error.

Recommended Action    No action is required.

CTS-3

Error Message     CTS-3-DOT1X_AUTHC_FAILED Format: DOT1X authentication failed on port: 
%s 

Explanation    DOT1X authentication failed on the port.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CTS-3-DOT1X_AUTHC_FAILED: DOT1X authentication failed on port: 
[chars] 

Explanation    DOT1X authentication failed on the port.

Recommended Action    No action is required.

CTS-5

Error Message     CTS-5-CTS_IP_SGT_MAP_DELETE: IP-SGT mapping deleted for [chars] on 
[chars] %lu 

Explanation    The system has detected an error.

Recommended Action    No action is required.

Error Message     CTS-5-CTS_IP_SGT_MAP_UPDATE: [chars] assigned SGT [chars] 

Explanation    The system has detected an error.

Recommended Action    No action is required.

Error Message     CTS-5-CTS_IP_SGT_MAP_UPDATE: [chars] assigned SGT [dec] 

Explanation    The system has detected an error.

Recommended Action    No action is required.

Error Message     CTS-5-IP_SGT_MAP_DELETE Format: IP-SGT mapping deleted for %s on %s 
%lu 

Explanation    The system has detected an error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CTS-5-IP_SGT_MAP_UPDATE Format: %s assigned SGT %s 

Explanation    The system has detected an error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

CTS-6

Error Message     CTS-6-CTS_FIPS_BYPASS_TEST_PASSED: FIPS bypass test passed for 
interface: [chars] 

Explanation    The system has detected an error.

Recommended Action    No action is required.

Error Message     CTS-6-FIPS_BYPASS_TEST_PASSED Format: FIPS bypass test passed for 
interface: %s 

Explanation    The system has detected an error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CTS-6-SXP_STATE_CHANGE Format: CTS SXP %s 

Explanation    The system has detected an error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     CTS-6-SXP_STATE_CHANGE: CTS SXP [chars] 

Explanation    The system has detected an error.

Recommended Action    No action is required.

DC3_XBC Messages

This section contains the DC3_XBC messages.

DC3_XBC-2

Error Message     DC3_XBC-2-PROC_INITFAIL Format: Process initialization failed due to 
%s. 

Explanation    XBAR_CLIENT process has failed initialization.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DCEFIB-SLOT# Messages

This section contains the DCEFIB-SLOT# messages.

DCEFIB-SLOT#-0

Error Message     DCEFIB-SLOT#-0-CLI_INIT_FAILED: CLI library initialization failed! 

Explanation    DCEFIB failed to initialize CLI infrastructure\sbackendlibrary.Thisisafatalerror.'

Recommended Action    No action is required.

Error Message     DCEFIB-SLOT#-0-TIMER_INIT_FAILED: Timer subsystem initialization 
failed! 

Explanation    DCEFIB failed to initialize timer library. This is a fatal error.

Recommended Action    No action is required.

DCEFIB-SLOT#-2

Error Message     DCEFIB-SLOT#-2-DCEFIB_MEM_ALLOC: Memory allocation failed. [chars] 

Explanation    Memory allocation failed. This is a critical failure.

Recommended Action    No action is required.

Error Message     DCEFIB-SLOT#-2-DCEFIB_RECOVERY_ERROR: Error in Recovery: [chars] 

Explanation    DCEFIB failed to recover after a re-start. This is a fatal error.

Recommended Action    No action is required.

Error Message     DCEFIB-SLOT#-2-U2FIB_ERR: [chars] 

Explanation    L2mp unicast fib encountered an error:.

Recommended Action    No action is required.

DCEFIB-SLOT#-6

Error Message     DCEFIB-SLOT#-6-INITIALIZED: Internal state created [chars] 

Explanation    DCEFIB has created its internal state stateless/stateful [chars].

Recommended Action    No action is required.

Error Message     DCEFIB-SLOT#-6-U2FIB_INFO: [chars] 

Explanation    L2mp unicast fib notice:.

Recommended Action    No action is required.

Error Message     DCEFIB-SLOT#-6-VDC_CREATED: VDC [dec] created 

Explanation    Request to create VDC [dec] in DCEFIB was successful.

Recommended Action    No action is required.

Error Message     DCEFIB-SLOT#-6-VDC_REMOVED: VDC [dec] Removed 

Explanation    DCEFIB has successfully removed VDC [dec] from its databases.

Recommended Action    No action is required.

DDAS Messages

This section contains the DDAS messages.

DDAS-2

Error Message     DDAS-2-ALLOC_FAILED Format: Memory allocation failed for size:%d 
type:%d 

Explanation    Memory allocation failed for size [dec] type [dec].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-2-INIT_FAILED Format: %s 

Explanation    An error occurred during initialization. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DDAS-3

Error Message     DDAS-3-CFS_OPER_FAILED Format: %s 

Explanation    An error occurred while performing a CFS operation. [chars] indicates the CFS operation and the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-3-CLEAR_FAILED Format: %s 

Explanation    An error occurred while clearing the session. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-3-COMMIT_FAILED Format: %s 

Explanation    An error occurred while committing the database. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-3-COMMIT_REJECTED Format: %s 

Explanation    Commit request received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-3-LOCK_FAILED Format: %s 

Explanation    An error occurred while acquiring the lock. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-3-LOCK_REJECTED Format: %s 

Explanation    Lock request received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-3-MERGE_ACTIVATION_FAILED Format: %s 

Explanation    An error occurred while activating the merged database. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-3-MERGE_ACTIVATION_REJECTED Format: %s 

Explanation    Merge activation request received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-3-MERGE_FAILED Format: %s 

Explanation    An error occurred during merge operation. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-3-MERGE_MREQ_REJECTED Format: %s 

Explanation    MREQ received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-3-MERGE_MRESP_REJECTED Format: %s 

Explanation    MRESP received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-3-MERGE_VALIDATION_FAILED Format: %s 

Explanation    An error occurred while validating the merged database. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-3-MERGE_VALIDATION_REJECTED Format: %s 

Explanation    Merge validation request received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-3-MTS_OPER_FAILED Format: %s 

Explanation    An error occurred during MTS operation. [chars] indicates the MTS operation and the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-3-PSS_OPER_FAILED Format: %s 

Explanation    An error occurred during PSS operation. [chars] indicates the PSS operation and the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-3-UNLOCK_FAILED Format: %s 

Explanation    An error occurred while releasing the lock. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-3-UNLOCK_REJECTED Format: %s 

Explanation    Unlock request received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-3-VALIDATION_FAILED Format: %s 

Explanation    An error occurred while validating the database. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-3-VALIDATION_REJECTED Format: %s 

Explanation    Validation request received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DDAS-6

Error Message     DDAS-6-CLEAR_FAILED_INFO Format: %s 

Explanation    An error occurred while clearing the session. [chars] indicates the additional information regarding failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-6-COMMIT_FAILED_INFO Format: %s 

Explanation    An error occurred while committing the database. [chars] indicates the additional information regarding failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-6-IMPORT_DEFINITION_CONFLICT Format: Fcalias %s could not be 
imported due to definition conflict 

Explanation    Fcalias [chars] could not be imported due to definition conflict. Either there is already a device-alias configuration present with the same definition OR another VSAN specified in the import VSAN range has an fcalias with the same definition.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-6-IMPORT_MEMBER_TYPE_CONFLICT Format: Fcalias %s could not be 
imported due to having unsupported member type 

Explanation    Fcalias [chars] could not be imported due to having unsupported member types. Fcalias can be imported only if it has Port WWN based members.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-6-IMPORT_NAME_CONFLICT Format: Fcalias %s could not be imported 
due to name conflict 

Explanation    Fcalias [chars] could not be imported due to name conflict. Either there is already a device-alias configuration present with the same name OR another VSAN specified in the import VSAN range has an fcalias with the same name.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-6-IMPORT_NUM_MEMBERS_CONFLICT Format: Fcalias %s could not be 
imported due to having unsupported number of members 

Explanation    Fcalias [chars] could not be imported due to having unsupported number of members. Fcalias can be imported only if it has exactly one member.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-6-LOCK_FAILED_INFO Format: %s 

Explanation    An error occurred while acquiring the lock. [chars] indicates the additional information regarding failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-6-MERGE_ACTIVATION_FAILED_INFO Format: %s 

Explanation    An error occurred while activating the merged database. [chars] indicates the additional information regarding failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-6-MERGE_VALIDATION_FAILED_BUSY Format: %s 

Explanation    Merged database could not be validated as some of the applications are busy. [chars] indicates information about the application returned busy. There is no user intervention necessary. The validation would be automatically retried after some time.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-6-MERGE_VALIDATION_REJECTED_BUSY Format: %s 

Explanation    Merged database received from the remote switch could not be validated as some of the applications are busy. [chars] indicates information about the application returned busy. There is no user intervention necessary. The validation would be automatically retried after some time.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-6-UNLOCK_FAILED_INFO Format: %s 

Explanation    An error occurred while releasing the lock. [chars] indicates the additional information regarding failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DDAS-6-VALIDATION_ABORTED Format: %s 

Explanation    Local validation is aborted. [chars] indicates the reason why validation is aborted.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DEBUGPROXY Messages

This section contains the DEBUGPROXY messages.

DEBUGPROXY-6

Error Message     DEBUGPROXY-6-SSM_DEBUG_PROXY_COMMON: SSM debug proxy [chars] [dec] 

Explanation    General SSM debug proxy information.

Recommended Action    No action is required.

DEV_LOG Messages

This section contains the DEV_LOG messages.

DEV_LOG-3

Error Message     DEV_LOG-3-ERROR: [chars] 

Explanation    Dev_log_lc encountered an error.

Recommended Action    No action is required.

DEV_LOG-SLOT# Messages

This section contains the DEV_LOG-SLOT# messages.

DEV_LOG-SLOT#-4

Error Message     DEV_LOG-SLOT#-4-DEV_LOG_LC_ERROR: [chars] 

Explanation    Dev_log_lc encountered an error.

Recommended Action    No action is required.

DEV_LOG_LC Messages

This section contains the DEV_LOG_LC messages.

DEV_LOG_LC-3

Error Message     DEV_LOG_LC-3-ERROR Format: %s 

Explanation    dev_log_lc encountered an error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DEVICE-ALIAS Messages

This section contains the DEVICE-ALIAS messages.

DEVICE-ALIAS-2

Error Message     DEVICE-ALIAS-2-ALLOC_FAILED: Memory allocation failed for size:[dec] 
type:[dec] 

Explanation    Memory allocation failed for size [dec] type [dec].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-2-INIT_FAILED: [chars] 

Explanation    An error occurred during initialization. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DEVICE-ALIAS-3

Error Message     DEVICE-ALIAS-3-CFS_OPER_FAILED: [chars] 

Explanation    An error occurred while performing a CFS operation. [chars] indicates the CFS operation and the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-3-CLEAR_FAILED: [chars] 

Explanation    An error occurred while clearing the session. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-3-COMMIT_FAILED: [chars] 

Explanation    An error occurred while committing the database. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-3-COMMIT_REJECTED: [chars] 

Explanation    Commit request received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-3-LOCK_FAILED: [chars] 

Explanation    An error occurred while acquiring the lock. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-3-LOCK_REJECTED: [chars] 

Explanation    Lock request received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-3-MERGE_ACTIVATION_FAILED: [chars] 

Explanation    An error occurred while activating the merged database. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-3-MERGE_ACTIVATION_REJECTED: [chars] 

Explanation    Merge activation request received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-3-MERGE_FAILED: [chars] 

Explanation    An error occurred during merge operation. [chars] indicates the reason for failure.

Recommended Action    Compare device-alias configuration with the other switches in the fabric, resolve the conflicts if any and commit the changes.

Error Message     DEVICE-ALIAS-3-MERGE_MREQ_REJECTED: [chars] 

Explanation    MREQ received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-3-MERGE_MRESP_REJECTED: [chars] 

Explanation    MRESP received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-3-MERGE_VALIDATION_FAILED: [chars] 

Explanation    An error occurred while validating the merged database. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-3-MERGE_VALIDATION_REJECTED: [chars] 

Explanation    Merge validation request received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-3-MTS_OPER_FAILED: [chars] 

Explanation    An error occurred during MTS operation. [chars] indicates the MTS operation and the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-3-PSS_OPER_FAILED: [chars] 

Explanation    An error occurred during PSS operation. [chars] indicates the PSS operation and the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-3-UNLOCK_FAILED: [chars] 

Explanation    An error occurred while releasing the lock. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-3-UNLOCK_REJECTED: [chars] 

Explanation    Unlock request received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-3-VALIDATION_FAILED: [chars] 

Explanation    An error occurred while validating the database. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-3-VALIDATION_REJECTED: [chars] 

Explanation    Validation request received from remote switch is rejected. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DEVICE-ALIAS-6

Error Message     DEVICE-ALIAS-6-CLEAR_FAILED_INFO: [chars] 

Explanation    An error occurred while clearing the session. [chars] indicates the additional information regarding failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-6-COMMIT_FAILED_INFO: [chars] 

Explanation    An error occurred while committing the database. [chars] indicates the additional information regarding failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-6-IMPORT_DEFINITION_CONFLICT: Fcalias [chars] could not 
be imported due to definition conflict

Explanation    Fcalias [chars] could not be imported due to definition conflict. Either there is already a device-alias configuration present with the same definition OR another VSAN specified in the import VSAN range has an fcalias with the same definition.

Recommended Action    Resolve the conflict and issue the import command again.

Error Message     DEVICE-ALIAS-6-IMPORT_MEMBER_TYPE_CONFLICT: Fcalias [chars] could not 
be imported due to having unsupported member type

Explanation    Fcalias [chars] could not be imported due to having unsupported member types. Fcalias can be imported only if it has Port WWN based members.

Recommended Action    Make sure that the fcalias has Port WWN based members and issue the import command again.

Error Message     DEVICE-ALIAS-6-IMPORT_NAME_CONFLICT: Fcalias [chars] could not be 
imported due to name conflict 

Explanation    Fcalias [chars] could not be imported due to name conflict. Either there is already a device-alias configuration present with the same name OR another VSAN specified in the import VSAN range has an fcalias with the same name.

Recommended Action    Resolve the conflict and issue the import command again.

Error Message     DEVICE-ALIAS-6-IMPORT_NUM_MEMBERS_CONFLICT: Fcalias [chars] could not 
be imported due to having unsupported number of members

Explanation    Fcalias [chars] could not be imported due to having unsupported number of members. Fcalias can be imported only if it has exactly one member.

Recommended Action    Make sure that the fcalias has exactly one member and issue the import command again.

Error Message     DEVICE-ALIAS-6-LOCK_FAILED_INFO: [chars] 

Explanation    An error occurred while acquiring the lock. [chars] indicates the additional information regarding failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-6-MERGE_ACTIVATION_FAILED_INFO: [chars] 

Explanation    An error occurred while activating the merged database. [chars] indicates the additional information regarding failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-6-MERGE_VALIDATION_FAILED_BUSY: [chars] 

Explanation    Merged database could not be validated as some of the applications are busy. [chars] indicates information about the application returned busy. There is no user intervention necessary. The validation would be automatically retried after some time.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-6-MERGE_VALIDATION_REJECTED_BUSY: [chars] 

Explanation    Merged database received from the remote switch could not be validated as some of the applications are busy. [chars] indicates information about the application returned busy. There is no user intervention necessary. The validation would be automatically retried after some time.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-6-UNLOCK_FAILED_INFO: [chars] 

Explanation    An error occurred while releasing the lock. [chars] indicates the additional information regarding failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE-ALIAS-6-VALIDATION_ABORTED: [chars] 

Explanation    Local validation is aborted. [chars] indicates the reason why validation is aborted.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DEVICE_TEST Messages

This section contains the DEVICE_TEST messages.

DEVICE_TEST-2

Error Message     DEVICE_TEST-2-ASIC_REG_CHECK_FAIL Format: Module %d has failed test 
%s %d times on device %s %s %d %s due to error %s 

Explanation    The online diagnostic ASICRegisterCheck test has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-2-ASIC_REG_CHECK_FAIL: Module [dec] has failed test 
[chars] [dec] times on device [chars] [chars] [dec] [chars] due to error [chars] 

Explanation    The online diagnostic ASICRegisterCheck test has failed.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-2-ASIC_REG_CHECK_FAIL: Module [dec] has failed test 
[chars] [dec] times on device [chars] [chars] [dec] frontpanel ports affected 
[chars] due to error [chars] 

Explanation    The online diagnostic ASICRegisterCheck test has failed.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-2-COMPACT_FLASH_FAIL Format: Module %d has failed test %s 
%d times on device Compact Flash due to error %s 

Explanation    The online diagnostic CompactFlash test has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-2-COMPACT_FLASH_FAIL: Module [dec] has failed test 
[chars] [dec] times on device Compact Flash due to error [chars] 

Explanation    The online diagnostic CompactFlash test has failed.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-2-CRYPTO_DEVICE_FAIL Format: Module %d has failed test %s 
%d times on Crypto device due to error %s 

Explanation    The online diagnostic CryptoDevice test has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-2-CRYPTO_DEVICE_FAIL: Module [dec] has failed test 
[chars] [dec] times on Crypto device due to error [chars] 

Explanation    The online diagnostic CryptoDevice test has failed.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-2-EOBC_FAIL Format: Module %d has failed test %s on EOBC 
due to error %s 

Explanation    The online diagnostic EOBC test has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-2-EOBC_FAIL: Module [dec] has failed test [chars] on EOBC 
due to error [chars] 

Explanation    The online diagnostic EOBC test has failed.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-2-FAN_MOD_FAIL Format: Module %d has failed test %s %d 
times on System Mgmt Bus for chassis %s instance %d due to error %s error number 
0x%08X 

Explanation    The online diagnostic The systemMgmtBus test has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-2-FAN_MOD_FAIL: Module [dec] has failed test [chars] 
[dec] times on System Mgmt Bus for chassis [chars] instance [dec] due to error 
[chars] error number [hex] 

Explanation    The online diagnostic The systemMgmtBus test has failed.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-2-MALLOC_FAILURE Format: Memory allocation failed 

Explanation    Device Test process could not allocate enough memory.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-2-MALLOC_FAILURE: Memory allocation failed 

Explanation    Device Test process could not allocate enough memory.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-2-MGMT_PORT_SKIP Format: Module %d has skipped test %s on 
Management Port due to error %s 

Explanation    The online diagnostic ManagementPort test is skipped.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-2-MGMT_PORT_SKIP: Module [dec] has skipped test [chars] 
on Management Port due to error [chars] 

Explanation    The online diagnostic ManagementPort test is skipped.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-2-NVRAM_FAIL Format: Module %d has failed test %s %d times 
on device NVRAM due to error %s 

Explanation    The online diagnostic NVRAM test has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-2-NVRAM_FAIL: Module [dec] has failed test [chars] [dec] 
times on device NVRAM due to error [chars] 

Explanation    The online diagnostic NVRAM test has failed.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-2-OBFL_FAIL Format: Module %d has failed test %s %d times 
on device OBFL due to error %s 

Explanation    The online diagnostic OBFL test has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-2-OBFL_FAIL: Module [dec] has failed test [chars] [dec] 
times on device OBFL due to error [chars]

Explanation    The online diagnostic OBFL test has failed.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-2-POWER_SUPPLY_FAIL Format: Module %d has failed test %s 
%d times on System Mgmt Bus for chassis %s instance %d due to error %s error number 
0x%08X 

Explanation    The online diagnostic The systemMgmtBus test has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-2-POWER_SUPPLY_FAIL: Module [dec] has failed test [chars] 
[dec] times on System Mgmt Bus for chassis [chars] instance [dec] due to error 
[chars] error number [hex] 

Explanation    The online diagnostic The systemMgmtBus test has failed.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-2-PRIMARY_BOOTROM_FAIL Format: Module %d has failed test 
%s %d times on device Primary BootROM due to error %s 

Explanation    The online diagnostic PrimaryBootROM test has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-2-PRIMARY_BOOTROM_FAIL: Module [dec] has failed test 
[chars] [dec] times on device Primary BootROM due to error [chars] 

Explanation    The online diagnostic PrimaryBootROM test has failed.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-2-PWR_MGMT_BUS_FAIL Format: Module %d has failed test %s 
%d times on device Power Mgmt Bus on slot %d due to error %s error number 0x%08X 

Explanation    The online diagnostic PwrMgmtBus test has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-2-PWR_MGMT_BUS_FAIL: Module [dec] has failed test [chars] 
[dec] times on device Power Mgmt Bus on slot [dec] due to error [chars] error 
number [hex] 

Explanation    The online diagnostic PwrMgmtBus test has failed.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-2-RTC_FAIL Format: Module %d has failed test %s %d times 
on device RealTimeClock due to error %s 

Explanation    The online diagnostic RealTimeClock test has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-2-RTC_FAIL: Module [dec] has failed test [chars] [dec] 
times on device RealTimeClock due to error [chars] 

Explanation    The online diagnostic RealTimeClock test has failed.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-2-SECONDARY_BOOTROM_FAIL Format: Module %d has failed 
test %s %d times on device Secondary BootROM due to error %s 

Explanation    The online diagnostic SecondaryBootROM test has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-2-SECONDARY_BOOTROM_FAIL: Module [dec] has failed test 
[chars] [dec] times on device Secondary BootROM due to error [chars] 

Explanation    The online diagnostic SecondaryBootROM test has failed.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-2-SPINE_CONTROL_BUS_FAIL Format: Module %d has failed 
test %s %d times on device Spine Control Bus on slot %d due to error %s error 
number 0x%08X 

Explanation    The online diagnostic SpineControlBus test has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-2-SPINE_CONTROL_BUS_FAIL: Module [dec] has failed test 
[chars] [dec] times on device Spine Control Bus on slot [dec] due to error [chars] 
error number [hex] 

Explanation    The online diagnostic SpineControlBus test has failed.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-2-STANDBY_LOOPBACK_TEST_FAIL Format: Module %d has failed 
test %s %d times on %s %d due to error %s 

Explanation    The online diagnostic StandbyFabricLoopback test has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-2-STANDBY_LOOPBACK_TEST_FAIL: Module [dec] has failed 
test [chars] [dec] times on [chars] [dec] due to error [chars] 

Explanation    The online diagnostic StandbyFabricLoopback test has failed.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-2-TWOWIRE_STW_FAIL Format: Module %d has failed test %s 
%d times on Status Bus on slot %d due to error %s 

Explanation    The online diagnostic Status bus test has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-2-TWOWIRE_STW_FAIL: Module [dec] has failed test [chars] 
[dec] times on Status Bus on slot [dec] due to error [chars] 

Explanation    The online diagnostic Status bus test has failed.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-2-USB_FAIL Format: Module %d has failed test %s %d times 
on device USB due to error %s 

Explanation    The online diagnostic USB test has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-2-USB_FAIL: Module [dec] has failed test [chars] [dec] 
times on device USB due to error [chars] 

Explanation    The online diagnostic USB test has failed.

Recommended Action    No action is required.

DEVICE_TEST-3

Error Message     DEVICE_TEST-3-STANDBY_TEST_GET_DIAG_VQI_FAIL: Standby test get diag 
vqi failed due to error [hex] 

Explanation    Device Test StandbyLoopback Test failed get vqi.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-3-STANDBY_TEST_GET_SPINE_FAIL: Standby test get spines 
failed due to error [hex] 

Explanation    Device Test StandbyFabricLoopback Test get spine failed.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-3-STANDBY_TEST_INIT_FAIL: Init for standby test failed 
due to error [hex] 

Explanation    Device Test StandbyFabricLoopback Test failed init process.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-3-STANDBY_TEST_MTS_FAIL: Mts Init for standby test failed 
due to error [hex] 

Explanation    Device Test StandbyFabricLoopback Test failed mts init.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-3-STANDBY_TEST_SOCKET_FAIL: Standby test socket error 
[chars]: [hex] 

Explanation    Device Test StandbyFabricLoopback Test Socket error.

Recommended Action    No action is required.

DEVICE_TEST-4

Error Message     DEVICE_TEST-4-THREAD_CREATE_FAIL Format: Thread creation failed 

Explanation    Device Test process could not create threads.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-4-THREAD_CREATE_FAIL: Thread creation failed 

Explanation    Device Test process could not create threads.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-4-TIMER_CREATE_FAIL Format: Timer creation failed 

Explanation    Device Test process could not create timer.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-4-TIMER_CREATE_FAIL: Timer creation failed 

Explanation    Device Test process could not create timer.

Recommended Action    No action is required.

Error Message     DEVICE_TEST-4-TIMER_START_FAIL Format: Timer start failed 

Explanation    Device Test process could not start timer.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-4-TIMER_START_FAIL: Timer start failed 

Explanation    Device Test process could not start timer.

Recommended Action    No action is required.

DEVICE_TEST-5

Error Message     DEVICE_TEST-5-NOTICE_TEST Format: Memory allocation failed notice 

Explanation    Device Test process could not allocate enough memory.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-5-NOTICE_TEST: Memory allocation failed notice 

Explanation    Device Test process could not allocate enough memory.

Recommended Action    No action is required.

DEVICE_TEST-6

Error Message     DEVICE_TEST-6-INFO_TEST Format: Memory allocation failed info 

Explanation    Device Test process could not allocate enough memory.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DEVICE_TEST-6-INFO_TEST: Memory allocation failed info 

Explanation    Device Test process could not allocate enough memory.

Recommended Action    No action is required.

DFTM Messages

This section contains the DFTM messages.

DFTM-3

Error Message     DFTM-3-DFTM_BDDB_PROG_FAILED: DFTM failed to program BDDB Entry: 
[chars] 

Explanation    DFTM failed to program BDDB Entry.

Recommended Action    No action is required.

Error Message     DFTM-3-DFTM_BDT_PROG_FAILED: DFTM failed to program BD Table Entry: 
[chars] 

Explanation    DFTM failed to program BD Table Entry.

Recommended Action    No action is required.

Error Message     DFTM-3-DFTM_L2L3CT_PROG_FAILED: DFTM failed to program L2L3 
Consistency Table Entry: [chars] 

Explanation    DFTM failed to program L2L3 Consistency Table Entry.

Recommended Action    No action is required.

Error Message     DFTM-3-DFTM_MFT_PROG_FAILED: DFTM failed to program Multicast FTag 
Table Entry: [chars] 

Explanation    DFTM failed to program Multicast Ftag Table Entry.

Recommended Action    No action is required.

Error Message     DFTM-3-DFTM_SDT_PROG_FAILED: DFTM failed to program SGT DGT Table 
Entry: [chars] 

Explanation    DFTM failed to program SGT DGT Table Entry.

Recommended Action    No action is required.

Error Message     DFTM-3-DFTM_VTT_PROG_FAILED: DFTM failed to program VLAN Translation 
Table Entry: [chars] 

Explanation    DFTM failed to program VLAN Translation Table.

Recommended Action    No action is required.

DFTM-SLOT# Messages

This section contains the DFTM-SLOT# messages.

DFTM-SLOT#-2

Error Message     DFTM-SLOT#-2-DFTM_INTF_NOT_FOUND: Interface [chars] not found in DFTM 
database [chars] 

Explanation    DFTM database does not have the interface.

Recommended Action    No action is required.

Error Message     DFTM-SLOT#-2-DFTM_INVALID_FTAG_NUM: DFTM received invalid number of 
FTags [dec] from M2RIB 

Explanation    DFTM recvd invalid number of FTags from M2RIB.

Recommended Action    No action is required.

Error Message     DFTM-SLOT#-2-DFTM_PC_NUM_MEMB_INVALID: DFTM received invalid number 
of PC members [dec] from ELTM 

Explanation    DFTM recvd invalid number of PC members from ELTM.

Recommended Action    No action is required.

Error Message     DFTM-SLOT#-2-DFTM_PC_NUM_MEMB_INVALID: DFTM recieved invalid number 
of PC members [dec] from ELTM 

Explanation    DFTM recvd invalid number of PC members from ELTM.

Recommended Action    No action is required.

Error Message     DFTM-SLOT#-2-DFTM_VLAN_NOT_FOUND: VLAN [dec] not found in DFTM 
database [chars] 

Explanation    DFTM database does not have the VLAN.

Recommended Action    No action is required.

DFTM-SLOT#-3

Error Message     DFTM-SLOT#-3-DFTM_BDDB_PROG_FAILED: DFTM failed to program BDDB Entry 

Explanation    DFTM failed to program BDDB Entry.

Recommended Action    No action is required.

Error Message     DFTM-SLOT#-3-DFTM_BDT_PROG_FAILED: DFTM failed to program BD Table 
Entry 

Explanation    DFTM failed to program BD Table Entry.

Recommended Action    No action is required.

Error Message     DFTM-SLOT#-3-DFTM_IFIDX_INVALID_PORT_LAYER: Invalid Port Layer 
Received for interface: [chars] 

Explanation    Invalid Port Layer Received for interface.

Recommended Action    No action is required.

Error Message     DFTM-SLOT#-3-DFTM_IFIDX_INVALID_PORT_MODE: Invalid Port Mode Received 
for interface: [chars] 

Explanation    Invalid Port Mode Received for interface.

Recommended Action    No action is required.

Error Message     DFTM-SLOT#-3-DFTM_IFIDX_INVALID_PORT_TYPE: Invalid Port Type Received 
for interface: [chars] 

Explanation    Invalid Port Type Received for interface.

Recommended Action    No action is required.

Error Message     DFTM-SLOT#-3-DFTM_IFIDX_TYPE_ERROR: Failed to get type for interface: 
[chars] 

Explanation    Failed to get type for the interface.

Recommended Action    No action is required.

Error Message     DFTM-SLOT#-3-DFTM_L2L3CT_PROG_FAILED: DFTM failed to program L2L3 
Consistency Table Entry 

Explanation    DFTM failed to program L2L3 Consistency Table Entry.

Recommended Action    No action is required.

Error Message     DFTM-SLOT#-3-DFTM_MFT_PROG_FAILED: DFTM failed to program Multicast 
FTag Table Entry 

Explanation    DFTM failed to program Multicast Ftag Table Entry.

Recommended Action    No action is required.

Error Message     DFTM-SLOT#-3-DFTM_SDT_PROG_FAILED: DFTM failed to program SGT DGT 
Table Entry 

Explanation    DFTM failed to program SGT DGT Table Entry.

Recommended Action    No action is required.

Error Message     DFTM-SLOT#-3-DFTM_VTT_PROG_FAILED: DFTM failed to program VLAN 
Translation Table Entry 

Explanation    DFTM failed to program VLAN Translation Table.

Recommended Action    No action is required.

DHCP_SNOOP Messages

This section contains the DHCP_SNOOP messages.

DHCP_SNOOP-2

Error Message     DHCP_SNOOP-2-DHCP_SNOOP_PROGRAM_EXIT: [chars] 

Explanation    DHCP snoop process did an abnormal exit.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-2-INITFAIL Format: DHCP Daemon Initialization failed: %s 

Explanation    DHCP daemon initialization failed. [chars] explains the reason for the failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-2-INITFAIL: DHCP Daemon Initialization failed: [chars] 

Explanation    DHCP daemon initialization failed. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-2-PROGRAM_EXIT Format: %s 

Explanation    DHCP snoop process did an abnormal exit.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-2-PSSERROR Format: %s 

Explanation    DHCP Daemon encountered a PSS error. [chars] specifies the context where the failure occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-2-PSSERROR: [chars] 

Explanation    DHCP Daemon encountered a PSS error. [chars] specifies the context where the failure occurred.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-2-REGPARTREE Format: Unable to register par tree: %s 

Explanation    Could not register par tree. [chars] explains the reason for the failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-2-REGPARTREE: Unable to register par tree: [chars] 

Explanation    Could not register par tree. [chars] explains the reason for the failure.

Recommended Action    No action is required.

DHCP_SNOOP-3

Error Message     DHCP_SNOOP-3-ALLOCFAIL Format: Heap Memory allocation failed: %s 

Explanation    DHCP Daemon is out of dynamic memory. [chars] specifies the context where the failure occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-3-ALLOCFAIL: Heap Memory allocation failed: [chars] 

Explanation    DHCP Daemon is out of dynamic memory. [chars] specifies the context where the failure occurred.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-3-ASSERTION_FAILED Format: %s:%d 

Explanation    DHCP Snoop process has hit an assert condition at file [chars] line number [dec].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-3-ASSERTION_FAILED: [chars]:[dec] 

Explanation    DHCP Snoop process has hit an assert condition at file [chars] line number [dec].

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-3-DHCPDENIEDARP Format: ARP frame denied due to DHCP 
snooping binding on interface %s vlan %d sender mac %s sender ip %s target mac %s 
target ip %s. 

Explanation    [chars] identifies interface and [dec] identifies the vlan on which ARP packets have been denied. [chars] identifies sender mac and [chars] identifies the sender ip. [chars] identifies the target mac and [chars] identifies the target ip.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-3-DHCPDENIEDARP: ARP frame denied due to DHCP snooping 
binding on interface [chars] vlan [dec] sender mac [chars] sender ip [chars] target 
mac [chars] target ip [chars].

Explanation    [chars] identifies interface and [dec] identifies the vlan on which ARP packets have been denied. [chars] identifies sender mac and [chars] identifies the sender ip. [chars] identifies the target mac and [chars] identifies the target ip.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-3-DHCPRATELIMIT Format: Interface %s has been error 
disabled due to excessive ingress rate %d of DHCP packets. 

Explanation    [chars] identifies the interface which has been error disabled due to excessive ingress rate [dec].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-3-DHCPRATELIMIT: Interface [chars] has been error disabled 
due to excessive ingress rate [dec] of DHCP packets.

Explanation    [chars] identifies the interface which has been error disabled due to excessive ingress rate [dec].

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-3-HWPGMFAILURE Format: Hardware programming has failed: %s 

Explanation    Hardware programming has failed. [chars] explains the reason for the failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-3-HWPGMFAILURE: Hardware programming has failed: [chars] 

Explanation    Hardware programming has failed. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-3-INVDHCPPKTS Format: Validation errors while processing 
DHCP packet received on interface %s vlan %d Reason:%s. Dropping the packet 

Explanation    Validation errors DHCP packet receieved on the interface [chars] vlan [%d]. Reason:[chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-3-INVDHCPPKTS: Validation errors while processing DHCP 
packet received on interface [chars] vlan [dec] Reason:[chars]. Dropping the 
packet

Explanation    Validation errors DHCP packet receieved on the interface [chars] vlan [[dec]]. Reason:[chars].

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-3-MTSERROR Format: %s 

Explanation    DHCP Daemon encountered an MTS error. [chars] specifies the context where the error occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-3-MTSERROR: [chars] 

Explanation    DHCP Daemon encountered an MTS error. [chars] specifies the context where the error occurred.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-3-PKTDROP Format: Packet dropped. Reason - %s 

Explanation    Dropping the packet. [char] identifies the reason.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-3-PKTDROP: Packet dropped. Reason - [chars] 

Explanation    Dropping the packet. [char] identifies the reason.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-3-PKTRECVFAIL Format: Failed to receive packet - %s 

Explanation    The system has failed to receive the packet. [char] identifies the reason.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-3-PKTRECVFAIL: Failed to receive packet - [chars] 

Explanation    The system has failed to receive the packet. [char] identifies the reason.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-3-PKTSENDFAIL Format: Failed to send packet 

Explanation    The system has failed to send the packet. [char] identifies the reason.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-3-PKTSENDFAIL: Failed to send packet, - [chars] 

Explanation    The system has failed to send the packet. [char] identifies the reason.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-3-SOCKBINDFAIL Format: Failed to bind to raw socket - %s 

Explanation    Failed to bind to socket. [char] identifies the reason.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-3-SOCKBINDFAIL: Failed to bind to raw socket - [chars] 

Explanation    Failed to bind to socket. [char] identifies the reason.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-3-SOCKOPENFAIL Format: Failed to open socket for receiving 
DHCP packets - %s 

Explanation    An attempt to open a socket for receiving DHCP packets failed. [char] identifies the reason.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-3-SOCKOPENFAIL: Failed to open socket for receiving DHCP 
packets - [chars] 

Explanation    An attempt to open a socket for receiving DHCP packets failed. [char] identifies the reason.

Recommended Action    No action is required.

DHCP_SNOOP-4

Error Message     DHCP_SNOOP-4-ACL_DENY: [dec] Invalid ARP messages ([chars]) on 
[chars], vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]])

Explanation    Packet-count [dec] Invalid ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]]).

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-4-ACL_PERMIT: [dec] ARP messages ([chars]) on [chars], 
vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]]) 

Explanation    Packet-count [dec] ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]]).

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-4-DHCP_SNOOPING_DENY: [dec] Invalid ARP messages ([chars]) 
on [chars], vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]])

Explanation    Packet-count [dec] Invalid ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]]).

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-4-DHCP_SNOOPING_PERMIT: [dec] ARP messages ([chars]) on 
[chars], vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]]) 

Explanation    Packet-count [dec] ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]]).

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-4-ERROR_DISABLED Format: Interface %s has moved to error 
disabled state due to excessive rate %d of ingress ARP packets 

Explanation    Interface [chars] has moved to error disabled state due to excessive rate [dec] of ingress ARP packets.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-4-ERROR_DISABLED: Interface [chars] has moved to error 
disabled state due to excessive rate [dec] of ingress ARP packets

Explanation    Interface [chars] has moved to error disabled state due to excessive rate [dec] of ingress ARP packets.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-4-INVALID_ARP: [dec] Invalid ARP messages ([chars]) on 
[chars], vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]])

Explanation    Packet-count [dec] Invalid ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]]).

Recommended Action    No action is required.

DHCP_SNOOP-6

Error Message     DHCP_SNOOP-6-DAIVLANDISABLE Format: DAI disabled on vlan %d 

Explanation    Dynamic ARP Inspection was disabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-6-DAIVLANDISABLE: DAI disabled on vlan [dec] 

Explanation    Dynamic ARP Inspection was disabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-6-DAIVLANENABLE Format: DAI enabled on vlan %d 

Explanation    Dynamic ARP Inspection was enabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-6-DAIVLANENABLE: DAI enabled on vlan [dec] 

Explanation    Dynamic ARP Inspection was enabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-6-DHCPBINDSYNC Format: Binding entry with MAC %s interface 
%s VLAN %d IP address %s and lease time %d secs is synced. 

Explanation    Binding entry identified by [chars] has been synced. [chars] identifies the interface. [dec] identifies the VLAN. [chars] identifies IP address. [dec] identifies the lease time in secs.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-6-DHCPBINDSYNC: Binding entry with MAC [chars] interface 
[chars] VLAN [dec] IP address [chars] and lease time [dec] secs is synced.

Explanation    Binding entry identified by [chars] has been synced. [chars] identifies the interface. [dec] identifies the VLAN. [chars] identifies IP address. [dec] identifies the lease time in secs.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-6-DHCPEXIT Format: DHCP Daemon shutting down gracefully. 

Explanation    DHCP Daemon is shutting down gracefully.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-6-DHCPEXIT: DHCP Daemon shutting down gracefully. 

Explanation    DHCP Daemon is shutting down gracefully.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-6-DHCPHOSTADD Format: A new Host is %s connected to 
interface %s in VLAN %d and is allocated IP address %s for %d secs. 

Explanation    A Host identified by [chars] has been added. [chars] identifies the interface. [dec] identifies the VLAN. [chars] identifies IP address. [dec] identifies the lease time in secs.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-6-DHCPHOSTADD: A new Host is [chars] connected to interface 
[chars] in VLAN [dec] and is allocated IP address [chars] for [dec] secs.

Explanation    A Host identified by [chars] has been added. [chars] identifies the interface. [dec] identifies the VLAN. [chars] identifies IP address. [dec] identifies the lease time in secs.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-6-DHCPLEASEEXPIRE Format: Lease expired for host %s having 
IP address %s connected to interface %s in VLAN %d for lease %d secs. 

Explanation    The lease for host identified by [chars] with IP address [chars] connected to interface [chars] in VLAN [dec] with lease [dec] has expired.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-6-DHCPLEASEEXPIRE: Lease expired for host [chars] having 
IP address [chars] connected to interface [chars] in VLAN [dec] for lease [dec] 
secs.

Explanation    The lease for host identified by [chars] with IP address [chars] connected to interface [chars] in VLAN [dec] with lease [dec] has expired.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-6-DHCPPERMITTEDARP Format: ARP frame permitted due to DHCP 
snooping binding on interface %s vlan %d sender mac %s sender ip %s target mac %s 
target ip %s. 

Explanation    [chars] identifies interface and [dec] identifies the vlan on which ARP packets have been permitted. [chars] identifies sender mac and [chars] identifies the sender ip. [chars] identifies the target mac and [chars] identifies the target ip.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-6-DHCPPERMITTEDARP: ARP frame permitted due to DHCP 
snooping binding on interface [chars] vlan [dec] sender mac [chars] sender ip 
[chars] target mac [chars] target ip [chars].

Explanation    [chars] identifies interface and [dec] identifies the vlan on which ARP packets have been permitted. [chars] identifies sender mac and [chars] identifies the sender ip. [chars] identifies the target mac and [chars] identifies the target ip.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-6-DHCPPKTFWD Format: Gracefully forwarding DHCP packet. 
Reason: %s 

Explanation    Gracefully forwarding DHCP packet. reason [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-6-DHCPPKTFWD: Gracefully forwarding DHCP packet. Reason: 
[chars] 

Explanation    Gracefully forwarding DHCP packet. reason [chars].

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-6-DHCPPKTFWD: Gracefully forwarding DHCP packet. 
reason:[chars] 

Explanation    Gracefully forwarding DHCP packet. reason [chars].

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-6-DHCPUP Format: DHCP Daemon Up. 

Explanation    DHCP Daemon was created successfully and is up and running.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-6-DHCPUP: DHCP Daemon Up. 

Explanation    DHCP Daemon was created successfully and is up and running.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-6-INFO Format: %s 

Explanation    An event during switchover. [chars] explains the reason for the failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-6-INFO: [chars] 

Explanation    An event during switchover. [chars] explains the reason for the failure.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-6-INTFDISABLE Format: IP Src Guard disabled on intf %s 

Explanation    IP Src Guard was disabled on a given intf. [chars] is the intf-ID string that identifies the intf.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-6-INTFDISABLE: IP Src Guard disabled on intf [chars] 

Explanation    IP Src Guard was disabled on a given intf. [chars] is the intf-ID string that identifies the intf.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-6-INTFENABLE Format: IP Src Guard enabled on intf %s 

Explanation    IP Src Guard was enabled on a given intf. [chars] is the intf-ID string that identifies the intf.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-6-INTFENABLE: IP Src Guard enabled on intf [chars] 

Explanation    IP Src Guard was enabled on a given intf. [chars] is the intf-ID string that identifies the intf.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-6-NONDHCPPKTFWD Format: Non DHCP packet with src port:%d 
dst port:%d on intf:%s vlan:%d. Forwarding on %s 

Explanation    Non DHCP packet arrived with UDP src/dst ports [dec], [dec] on interface [chars], vlan [dec]. Forwarding the packet on [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-6-NONDHCPPKTFWD: Non DHCP packet with src port:[dec] dst 
port:[dec] on intf:[chars] vlan:[dec]. Forwarding on [chars]

Explanation    Non DHCP packet arrived with UDP src/dst ports [dec], [dec] on interface [chars], vlan [dec]. Forwarding the packet on [chars].

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-6-OPT82INSTFAIL Format: %s %s 

Explanation    Insertion of Option82 suboptions failed. [chars] tells the failure. [chars] explains the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-6-OPT82INSTFAIL: [chars] [chars] 

Explanation    Insertion of Option82 suboptions failed. [chars] tells the failure. [chars] explains the reason for failure.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-6-VLANDISABLE Format: DHCP Snooping disabled on vlan %d 

Explanation    DHCP Snooping was disabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-6-VLANDISABLE: DHCP Snooping disabled on vlan [dec] 

Explanation    DHCP Snooping was disabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.

Recommended Action    No action is required.

Error Message     DHCP_SNOOP-6-VLANENABLE Format: DHCP Snooping enabled on vlan %d 

Explanation    DHCP Snooping was enabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DHCP_SNOOP-6-VLANENABLE: DHCP Snooping enabled on vlan [dec] 

Explanation    DHCP Snooping was enabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.

Recommended Action    No action is required.

DIAG_PORT_LB Messages

This section contains the DIAG_PORT_LB messages.

DIAG_PORT_LB-2

Error Message     DIAG_PORT_LB-2-FIPS_RANDOM_ERROR Format: Random Number Generation 
Failure 

Explanation    Random Number genration failed in FIPS module.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAG_PORT_LB-2-FIPS_RANDOM_ERROR: Random Number Generation Failure 

Explanation    Random Number genration failed in FIPS module.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-2-LCM_RESP_SEND_FAILURE Format: LC Inserted request 
response send to Module Manager failed . Error:%s 

Explanation    Failed to send the response for LC insertion to Module Manager.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAG_PORT_LB-2-LCM_RESP_SEND_FAILURE: LC Inserted request response 
send to Module Manager failed . Error:[chars]

Explanation    Failed to send the response for LC insertion to Module Manager.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-2-LIF_GET_ERROR: [chars]([dec]) [chars] Error:[chars] 

Explanation    Port Loopback test process failed to get Diagnostic LIF id.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-2-MALLOC_FAILURE: [chars]([dec]) Memory allocation 
failed. 

Explanation    Port Loopback test process could not allocate enough memory.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-2-PORTLOOPBACK_TEST_FAIL Format: Module:%d 
Test:PortLoopback failed %d consecutive times. Faulty module:%s %s Error:%s 

Explanation    PortLoopback test failed on the module consecutively.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAG_PORT_LB-2-PORTLOOPBACK_TEST_FAIL: Module:[dec] 
Test:PortLoopback failed [dec] consecutive times. Faulty module:[chars] [chars] 
Error:[chars]

Explanation    PortLoopback test failed on the module consecutively.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-2-PORTLOOPBACK_TEST_FAIL: Module:[dec] 
Test:PortLoopback failed [dec] consecutive times. Faulty module:[chars] affected 
ports:[chars] Error:[chars]

Explanation    PortLoopback test failed on the module consecutively.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-2-PROC_INIT_FAILURE: [chars]([dec]) [chars] 
Error:[chars] 

Explanation    Port Loopback test process failed in process initialization.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-2-REWRITE_ENGINE_LOOPBACK_TEST_FAIL Format: Module:%d 
Test:RewriteEngine Loopback failed %d consecutive times. Faulty module:%s %s 
Error:%s 

Explanation    Rewrite Engine Loopback test failed on the module consecutively.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAG_PORT_LB-2-REWRITE_ENGINE_LOOPBACK_TEST_FAIL: Module:[dec] 
Test:RewriteEngine Loopback failed [dec] consecutive times. Faulty module:[chars] 
[chars] Error:[chars]

Explanation    Rewrite Engine Loopback test failed on the module consecutively.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-2-REWRITE_ENGINE_LOOPBACK_TEST_FAIL: Module:[dec] 
Test:RewriteEngine Loopback failed [dec] consecutive times. Faulty module:[chars] 
affected ports:[chars] Error:[chars]

Explanation    Rewrite Engine Loopback test failed on the module consecutively.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-2-SNAKE_TEST_LOOPBACK_TEST_FAIL Format: Module:%d 
Test:SnakeLoopback failed %d consecutive times. Faulty module:%s affected ports:%s 
Error:%s 

Explanation    Snake test failed on the module consecutively.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAG_PORT_LB-2-SNAKE_TEST_LOOPBACK_TEST_FAIL: Module:[dec] 
Test:SnakeLoopback failed [dec] consecutive times. Faulty module:[chars] affected 
ports:[chars] Error:[chars]

Explanation    Snake test failed on the module consecutively.

Recommended Action    No action is required.

DIAG_PORT_LB-3

Error Message     DIAG_PORT_LB-3-DIAG_FWD_PATH_SETUP_FAILURE Format: %s. Module:%d 
Error:%s. 

Explanation    Forwarding path setup for port loopback tests failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAG_PORT_LB-3-DIAG_FWD_PATH_SETUP_FAILURE: [chars]. Module:[dec] 
Error:[chars]. 

Explanation    Forwarding path setup for port loopback tests failed.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-DIAG_PKT_SEND_FAILURE: [chars]([dec]) [chars]. 
Error:[chars] 

Explanation    Port Loopback test process failed to send loopback packets.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-FSM_LIB_ERROR: [chars]([dec]) [chars]. Error:[chars] 

Explanation    Port Loopback test process failed in MTS API.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-GET_DIAG_BD_FAIL: [chars]([dec]) Failed to get the BD 
for Diag VLAN:[dec]. Error:[chars]. 

Explanation    Failed to get the BD corresponding to the Diag VLAN.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-IFINDEX_LIB_FAILURE: [chars]([dec]) [chars] 
[chars]:[hex] [chars] [chars] 

Explanation    Port Loopback test process failed in if_index library API.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-INVALID_TEST_REQUEST: [chars]([dec]) [chars]:[dec] 

Explanation    Port Loopback test process failed to get test request info.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-INVALID_TEST_RUN: [chars]([dec]) [chars]:[dec] 

Explanation    Port Loopback test process failed to get the current test run information.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-MTS_LIB_ERROR: [chars]([dec]) [chars]. Error:[chars] 

Explanation    Port Loopback test process failed in MTS API.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-PDB_LIB_API_ERROR Format: Failed to %s. Error:%d. 

Explanation    The port loopback test was not able to get chassis information.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAG_PORT_LB-3-PDB_LIB_API_ERROR: Failed to [chars]. Error:[dec]. 

Explanation    The port loopback test was not able to get chassis information.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-PIXM_LIB_ERROR: [chars]([dec]) Failed to convert 
[chars]:[hex] to [chars]. Error:[chars] 

Explanation    Port Loopback test process failed to convert port ifindex <-> port index.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-PORT_CFG_REQ_SEND: [chars]([dec]) Failed to send 
request to configure port ifindex:[dec] for port loopback test

Explanation    Failed to configure/restore the port to do/cleanup port loopback testing.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-PORT_CLIENT_LIB_ERROR: [chars]([dec]) [chars]. 
Error:[chars] 

Explanation    Port Loopback test process failed in Port Client API.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-RESULT_ADD_FAILURE: [chars]([dec]) [chars]:[dec] 

Explanation    Port Loopback test process failed to add the port test result.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-RESULT_SEND_FAILURE: [chars]([dec]) [chars] 

Explanation    Port Loopback test process failed to send the test results.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-RW_ENGINE_LOOPBACK_TEST_SPINE_PATH_FAIL Format: 
Module:%d Test:RewriteEngine Loopback Spine path:%d failed %d consecutive times. 
Error:%s 

Explanation    Rewrite Engine Loopback test failed on the spine path consecutively.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAG_PORT_LB-3-RW_ENGINE_LOOPBACK_TEST_SPINE_PATH_FAIL: Module:[dec] 
Test:RewriteEngine Loopback Spine path:[dec] failed [dec] consecutive times. 
Error:[chars]

Explanation    Rewrite Engine Loopback test failed on the spine path consecutively.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-SOCKET_ERROR: [chars]([dec]) [chars] Error:[chars] 

Explanation    Port Loopback test process failed in socket operations.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-STATS_LIB_ERROR: [chars]([dec]) [chars]:[dec] 

Explanation    Port Loopback test process failed in stats infra lib API.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-TEST_RES_SEND_FAIL Format: Failed to send %s test 
results back to Diagnostics Infrastucture. Error:%s. 

Explanation    The port loopback test was not able to send the test results.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAG_PORT_LB-3-TEST_RES_SEND_FAIL: Failed to send [chars] test 
results back to Diagnostics Infrastucture. Error:[chars].

Explanation    The port loopback test was not able to send the test results.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-TIMER_LIB_ERROR: [chars]([dec]) [chars] 

Explanation    Port Loopback test process timer handling failure.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-VLAN_ERROR: [chars]([dec]) [chars] Error:[chars] 

Explanation    Port Loopback test process failed to get Diagnostic VLAN information.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-VQI_GET_FAIL Format: Failed to get the Diag VQi from 
XBM. Error:%s 

Explanation    Rewrite Engine Loopback test failed to get the Diag VQi from XBAR Mgr.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAG_PORT_LB-3-VQI_GET_FAIL: Failed to get the Diag VQi from XBM. 
Error:[chars] 

Explanation    Rewrite Engine Loopback test failed to get the Diag VQi from XBAR Mgr.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-3-XBM_CFG_REQ_FAIL Format: Failed to conigure the XBAR 
mask while running the RewriteEngineLoopback test. Error:%s. Module:%d could have 
gone offline 

Explanation    Rewrite Engine Loopback test failed to set the XBAR mask while running the test. The target module could have gone offline.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAG_PORT_LB-3-XBM_CFG_REQ_FAIL: Failed to conigure the XBAR mask 
while running the RewriteEngineLoopback test. Error:[chars]. Module:[dec] could 
have gone offline

Explanation    Rewrite Engine Loopback test failed to set the XBAR mask while running the test. The target module could have gone offline.

Recommended Action    No action is required.

DIAG_PORT_LB-4

Error Message     DIAG_PORT_LB-4-MTS_LIB_ERROR: [chars]([dec]) [chars]. 
Warning:[chars] 

Explanation    Port Loopback test process failed in MTS API.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-4-PORT_CFG_REQ_SEND: [chars]([dec]) Failed to send 
request to configure port ifindex:[dec] for port loopback test

Explanation    Failed to configure/restore the port to do/cleanup port loopback testing.

Recommended Action    No action is required.

DIAG_PORT_LB-5

Error Message     DIAG_PORT_LB-5-DIAG_PORT_LB_DISABLED: DIAG_PORT_LB Disabled 

Explanation    DIAG_PORT_LB Service Disabled.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-5-DIAG_PORT_LB_ENABLED: DIAG_PORT_LB Enabled 

Explanation    DIAG_PORT_LB Service nabled.

Recommended Action    No action is required.

Error Message     DIAG_PORT_LB-5-DISABLED Format: DIAG_PORT_LB Disabled 

Explanation    DIAG_PORT_LB Service Disabled.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAG_PORT_LB-5-ENABLED Format: DIAG_PORT_LB Enabled 

Explanation    DIAG_PORT_LB Service nabled.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DIAGCLIENT Messages

This section contains the DIAGCLIENT messages.

DIAGCLIENT-2

Error Message     DIAGCLIENT-2-DIAG_BOOTUP_COMPLETE Format: /* MODULE_ID 

Explanation    Bootup Test completed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGCLIENT-2-DIAG_BOOTUP_COMPLETE: Module <[dec]> Bootup Test 
<[chars]> has reported <[chars]>

Explanation    Bootup Test completed.

Recommended Action    Nothing to be done if the test reports SUCCESS otherwise copy the error message exactly as it appears on the console, gather the output of show tech-support, and contact your Cisco technical support representative with the gathered information.

Error Message     DIAGCLIENT-2-EEM_ACTION_HM_SHUTDOWN Format: Test <%s> has been 
disabled as a part of default EEM action 

Explanation    Informational Syslog.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGCLIENT-2-EEM_ACTION_HM_SHUTDOWN: Test <[chars]> has been disabled 
as a part of default EEM action 

Explanation    Informational Syslog.

Recommended Action    No action is required.

Error Message     DIAGCLIENT-2-PSS_READ_FAILURE Format: /* MODULE_ID */ Read from PSS 
failed on Module <%d> 

Explanation    Read operation from PSS store failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGCLIENT-2-PSS_READ_FAILURE: Read from PSS failed on Module <[dec]>

Explanation    Read operation from PSS store failed.

Recommended Action    No action is required.

Error Message     DIAGCLIENT-2-PSS_WRITE_FAILURE Format: /* MODULE_ID */ Write to PSS 
failed on Module <%d> 

Explanation    Write operation on PSS store failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGCLIENT-2-PSS_WRITE_FAILURE: Write to PSS failed on Module <[dec]>

Explanation    Write operation on PSS store failed.

Recommended Action    No action is required.

DIAGCLIENT-3

Error Message     DIAGCLIENT-3-DIAG_HM_FAIL Format: Module <%d> Health Monitoring Test 
<%s> has failed. Please use 'show diagnostic result <target>' to see test results 

Explanation    A Health Monitoring Test has reported failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGCLIENT-3-DIAG_HM_FAIL: Module <[dec]> Health Monitoring Test 
<[chars]> has failed. Please use 'show diagnostic result <target>' to see test 
results

Explanation    A Health Monitoring Test has reported failure.

Recommended Action    Ensure the line card is firmly in the slot, reseat if necessary, and attempt to run the test again if the line card is not seated properly in the slot. If the line card was properly seated in the slot, copy the error message exactly as it appears on the console, gather the output of show tech-support, and contact your Cisco technical support representative with the gathered information.

Error Message     DIAGCLIENT-3-ONDEMAND_FAIL_EXCESS Format: Module <%d> Test <%s> has 
failed more than <%d> number of times 

Explanation    Ondemand test has failed more than configured number of times.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGCLIENT-3-ONDEMAND_FAIL_EXCESS: Module <[dec]> Test <[chars]> has 
failed more than <[dec]> number of times 

Explanation    Ondemand test has failed more than configured number of times.

Recommended Action    Copy the error message exactly as it appears on the console, gather the output of show tech-support, and contact your Cisco technical support representative with the gathered information.

Error Message     DIAGCLIENT-3-PER_PORT_TEST_FAIL: Module <[dec]> Test <[chars]> has 
failed on Ports <[chars]> Please use 'show diagnostic result <target>' to see test 
results

Explanation    Per Port Test has failed on the above all ports.

Recommended Action    No action is required.

DIAGCLIENT-4

Error Message     DIAGCLIENT-4-LC_OFFLINE_FOR_CURR_SLOT Format: Received LC offline 
event for the current slot:%d. Ignoring it 

Explanation    Informational Syslog.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGCLIENT-4-LC_OFFLINE_FOR_CURR_SLOT: Received LC offline event for 
the current slot:[dec]. Ignoring it 

Explanation    Informational Syslog.

Recommended Action    No action is required.

Error Message     DIAGCLIENT-4-MTS_SEND_FAILURE Format: MTS send failed 

Explanation    MTS send reports failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGCLIENT-4-MTS_SEND_FAILURE: MTS send failed, mts_opc: [chars], 
dest slot: [dec], dest SAP: [dec], error-id: [hex] 

Explanation    MTS send reports failure.

Recommended Action    No action is required.

DIAGCLIENT-5

Error Message     DIAGCLIENT-5-CALLOC_FAILURE Format: Memory allocation failed 

Explanation    DiagClient process could not allocate enough memory.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGCLIENT-5-CALLOC_FAILURE: Memory allocation failed 

Explanation    DiagClient process could not allocate enough memory.

Recommended Action    No action is required.

Error Message     DIAGCLIENT-5-DIAG_ONDEMAND_TEST_FINISH Format: Module %d: Ondemand 
test %s finished 

Explanation    Informational Syslog.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGCLIENT-5-DIAG_ONDEMAND_TEST_FINISH: Module [dec]: Ondemand test 
[chars] finished 

Explanation    Informational Syslog.

Recommended Action    No action is required.

Error Message     DIAGCLIENT-5-DIAG_ONDEMAND_TEST_START Format: Module %d: Ondemand 
test %s started 

Explanation    Informational Syslog.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGCLIENT-5-DIAG_ONDEMAND_TEST_START: Module [dec]: Ondemand test 
[chars] started 

Explanation    Informational Syslog.

Recommended Action    No action is required.

Error Message     DIAGCLIENT-5-DIAG_ONDEMAND_TEST_STOP Format: Module %d: Ondemand test 
%s stopped 

Explanation    Informational Syslog.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGCLIENT-5-DIAG_ONDEMAND_TEST_STOP: Module [dec]: Ondemand test 
[chars] stopped 

Explanation    Informational Syslog.

Recommended Action    No action is required.

Error Message     DIAGCLIENT-5-DIAG_SCHED_COMPLETE Format: Module <%d> Test <%s> has 
completed Scheduled Testing 

Explanation    A scheduled Test was completed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGCLIENT-5-DIAG_SCHED_COMPLETE: Module <[dec]> Test <[chars]> has 
completed Scheduled Testing 

Explanation    A scheduled Test was completed.

Recommended Action    No action is required.

Error Message     DIAGCLIENT-5-ONDEMAND_FAIL Format: Module <%d> Test <%s> has failed 
in Test_Iteration <%d> 

Explanation    The specified test has reported FAILURE in this Iteration.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGCLIENT-5-ONDEMAND_FAIL: Module <[dec]> Test <[chars]> has failed 
in Test_Iteration <[dec]> 

Explanation    The specified test has reported FAILURE in this Iteration.

Recommended Action    No action is required.

Error Message     DIAGCLIENT-5-ONDEMAND_SUCCESS Format: Module <%d> Test <%s> has 
completed successfully in Test_Iteration <%d> 

Explanation    The specified test has reported SUCCESS in this Iteration.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGCLIENT-5-ONDEMAND_SUCCESS: Module <[dec]> Test <[chars]> has 
completed successfully in Test_Iteration <[dec]> 

Explanation    The specified test has reported SUCCESS in this Iteration.

Recommended Action    No action is required.

Error Message     DIAGCLIENT-5-PER_PORT_TEST_FAIL Format: /* MODULE_ID 

Explanation    Per Port Test has failed on the above all ports.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGCLIENT-5-PER_PORT_TEST_FAIL: Module <[dec]> Test <[chars]> has 
failed on Ports <[chars]> Please use 'show diagnostic result <target>' to see test 
results

Explanation    Per Port Test has failed on the above all ports.

Recommended Action    No action is required.

DIAGMGR Messages

This section contains the DIAGMGR messages.

DIAGMGR-2

Error Message     DIAGMGR-2-MTS_SEND_FAILURE Format: MTS send failed 

Explanation    MTS send reports failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGMGR-2-MTS_SEND_FAILURE: MTS send failed, mts_opc: [chars], dest 
slot: [dec], dest SAP: [dec], error-id: [hex] 

Explanation    MTS send reports failure.

Recommended Action    No action is required.

Error Message     DIAGMGR-2-PSS_DELETE_FAILURE Format: Read from PSS failed on Module 
<%d> 

Explanation    Read operation from PSS store failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGMGR-2-PSS_DELETE_FAILURE: Read from PSS failed on Module <[dec]> 

Explanation    Read operation from PSS store failed.

Recommended Action    No action is required.

Error Message     DIAGMGR-2-PSS_WRITE_FAILURE Format: Write to PSS failed on Module <%d> 

Explanation    Write operation on PSS store failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGMGR-2-PSS_WRITE_FAILURE: Write to PSS failed on Module <[dec]> 

Explanation    Write operation on PSS store failed.

Recommended Action    No action is required.

DIAGMGR-3

Error Message     DIAGMGR-3-DIAG_MAJOR_DEFECT Format: Module <%d> Test <%s> detected a 
Major Error Please use 'show diagnostic result <target>' to see test results 

Explanation    A major error was detected during diagnostic testing.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGMGR-3-DIAG_MAJOR_DEFECT: Module <[dec]> Test <[chars]> detected 
a Major Error Please use 'show diagnostic result <target>' to see test results

Explanation    A major error was detected during diagnostic testing.

Recommended Action    Re-seat the card and retry the test. If the same result occurs after reseating the card and retrying the test, copy the error message exactly as it appears on the screen and gather the output of show tech-support and any other relevant information. Contact your technical support representative with the gathered information.

Error Message     DIAGMGR-3-DIAG_MINOR_DEFECT Format: Module <%d> Test <%s> detected a 
Minor Error Please use 'show diagnostic result <target>' to see test results 

Explanation    A mior error was detected during diagnostic testing.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGMGR-3-DIAG_MINOR_DEFECT: Module <[dec]> Test <[chars]> detected 
a Minor Error Please use 'show diagnostic result <target>' to see test results

Explanation    A mior error was detected during diagnostic testing.

Recommended Action    Re-seat the card and retry the test. If the same result occurs after reseating the card and retrying the test, copy the error message exactly as it appears on the screen and gather the output of show tech-support and any other relevant information. Contact your technical support representative with the gathered information.

Error Message     DIAGMGR-3-GET_CURR_SLOT_FAIL Format: Failed to get the current slot 
for the process. Error:%s 

Explanation    The process initialization failed to get the current slot.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGMGR-3-GET_CURR_SLOT_FAIL: Failed to get the current slot for the 
process. Error:[chars] 

Explanation    The process initialization failed to get the current slot.

Recommended Action    This is an informational message stating that a process initialization failure.

DIAGMGR-4

Error Message     DIAGMGR-4-CURR_SLOT_OFFLINE Format: Recevied an LC offline event for 
the current slot:%d. Ignoring it 

Explanation    The process received an offline event for the slot it is running. Ignoring it.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGMGR-4-CURR_SLOT_OFFLINE: Recevied an LC offline event for the 
current slot:[dec]. Ignoring it 

Explanation    The process received an offline event for the slot it is running. Ignoring it.

Recommended Action    This is an informational message stating that an unexpected event has been encountered.

Error Message     DIAGMGR-4-DISRPT_TST_START Format: Starting Test <%s> on Module <%d> 
is Disruptive 

Explanation    Starting a Disruptive Test can disturb the system's normal functionality.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGMGR-4-DISRPT_TST_START: Starting Test <[chars]> on Module <[dec]> 
is Disruptive 

Explanation    Starting a Disruptive Test can disturb the system's normal functionality.

Recommended Action    Reset target module.

Error Message     DIAGMGR-4-FIXED_INTRVL_CHANGED Format: /*TestName*/ The users are not 
allowed to change monitoring interval of Test <%s> 

Explanation    The specified health monitoring test interval is not user-configurable and therefore cannot be changed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGMGR-4-FIXED_INTRVL_CHANGED: The users are not allowed to change 
monitoring interval of Test <[chars]>

Explanation    The specified health monitoring test interval is not user-configurable and therefore cannot be changed.

Recommended Action    No action is required.The specific health monitoring interval is not user- configurable by design so nothing can be done to change the interval.

DIAGMGR-5

Error Message     DIAGMGR-5-BOOTUP_CONF Format: /*COMPLETE/BYPASS*/ Diagnostic Bootup 
Level: <%s> 

Explanation    Current Diagnostic BootUp Level being configure or changed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGMGR-5-BOOTUP_CONF: Diagnostic Bootup Level: <[chars]>

Explanation    Current Diagnostic BootUp Level being configure or changed.

Recommended Action    No action is required.

Error Message     DIAGMGR-5-CALLOC_FAILURE Format: Memory allocation failure 

Explanation    Memory allocation in a call to malloc/calloc has failed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGMGR-5-CALLOC_FAILURE: Memory allocation failure 

Explanation    Memory allocation in a call to malloc/calloc has failed.

Recommended Action    No action is required.

Error Message     DIAGMGR-5-CHANGE_ALWAYS_HM Format: Health Monitoring test <%s> in 
Module <%d> is a must run and cannot be modified 

Explanation    The specified health monitoring test must be run and cannot be disabled.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGMGR-5-CHANGE_ALWAYS_HM: Health Monitoring test <[chars]> in 
Module <[dec]> is a must run and cannot be modified

Explanation    The specified health monitoring test must be run and cannot be disabled.

Recommended Action    No action is required.The specific health monitoring test cannot be disabled by design. The system is working properly.

Error Message     DIAGMGR-5-HM_START Format: Health monitoring test <%s> for Module <%d> 

Explanation    Health Monitoring Test started.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGMGR-5-HM_START: Health monitoring test <[chars]> for Module 
<[dec]> 

Explanation    Health Monitoring Test started.

Recommended Action    No action is required.

Error Message     DIAGMGR-5-HM_STOP Format: Disabling health monitoring test <%s> for 
Module <%d> 

Explanation    Health Monitoring Test has been stopped It can be enabled through the diagnostic monitor..... command.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGMGR-5-HM_STOP: Disabling health monitoring test <[chars]> for 
Module <[dec]> 

Explanation    Health Monitoring Test has been stopped It can be enabled through the diagnostic monitor..... command.

Recommended Action    No action is required.

Error Message     DIAGMGR-5-INTRVL_INCORRECT Format: Monitoring Interval is less than 
minimum of %d seconds required for Module <%d> test <%s> 

Explanation    Health Monitoring cannot be enabled for the specified test because the interval for the test has been incorrectly set.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGMGR-5-INTRVL_INCORRECT: Monitoring Interval is less than minimum 
of [dec] seconds required for Module <[dec]> test <[chars]>

Explanation    Health Monitoring cannot be enabled for the specified test because the interval for the test has been incorrectly set.

Recommended Action    The system is working properly and no action is required. If you want to specify a smaller testing interval, the error message text provides the lowest possible configurable interval for the specified monitoring interval.

Error Message     DIAGMGR-5-MODULE_MISSING Format: Diagnostic command issued on 
non-existing Module <%d> 

Explanation    A line card could not be located in a slot where a diagnostic action was requested.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGMGR-5-MODULE_MISSING: Diagnostic command issued on non-existing 
Module <[dec]> 

Explanation    A line card could not be located in a slot where a diagnostic action was requested.

Recommended Action    Ensure the targeted line card is properly seated in the specified slot. If the line card is properly seated, ensure the correct slot was indicated in the command-line interface. If the line card is well-seated and the correct slot was specified, copy the error message exactly as it appears on the screen as well as the output of show tech-support and paste the output into a separate file. Contact your technical support representative with the gathered information.

Error Message     DIAGMGR-5-NONHM_AS_HM Format: The Test <%s> cannot be used as health 
monitoring test 

Explanation    Non-HM test cannot be scheduled to run as a Health Monitoring test.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGMGR-5-NONHM_AS_HM: The Test <[chars]> cannot be used as health 
monitoring test 

Explanation    Non-HM test cannot be scheduled to run as a Health Monitoring test.

Recommended Action    No action is required.

DIAGMGR-6

Error Message     DIAGMGR-6-BOOTUP_DIAG_OK Format: /* MODULE_ID */ Module <%d>: Passed 
Online Diagnostics 

Explanation    The diagnostic tests did not detect any error on the card.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGMGR-6-BOOTUP_DIAG_OK: Module <[dec]>: Passed Online Diagnostics

Explanation    The diagnostic tests did not detect any error on the card.

Recommended Action    This is an informational message stating that the line card passed the diagnostic tests.

Error Message     DIAGMGR-6-BOOTUP_TEST_STARTED Format: /* MODULE_ID 

Explanation    Starting bootup testing for above module.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DIAGMGR-6-BOOTUP_TEST_STARTED: Module <[dec]>: Running [chars] 
Diagnostics

Explanation    Starting bootup testing for above module.

Recommended Action    No action is required.

DM Messages

This section contains the DM messages.

DM-2

Error Message     DM-2-FC2_INITIALIZATION_FAILED Format: FC initialization sequence 
failed 

Explanation    The fcdomain has not been able to complete the initialization sequence with the Fibre Channel subsystem. fcdomain depends on resources not available at the moment: the switch might be short in memory or some other component might be unable to provide the necessary information to fcdomain.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-2-FC2_SET_SOCKOPT_DM_SOCK_FAILED Format: set sockopt to FC2 
Service failed 

Explanation    fcdomain has not been able to setsockopt to the FC2 module.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-2-FC2BIND_FAILED Format: Bind to FC2 Service failed 

Explanation    fcdomain has not been able to contact the FC2 module.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-2-FCID_PERSISTENT_TBL_COMPLETELY_FULL Format: FCID persistent 
table is completely full 

Explanation    The FCID persistent table is full. Perform [show fcdomain fcid persistent VSAN <vsan-id>] to view the entries currently in the table. No more entries can be saved as persistent FCIDs across reboots.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-2-INITIALIZATION_FAILED Format: Initialization sequence failed 

Explanation    The fcdomain has not been able to complete the initialization sequence. fcdomain depends on resources not available at the moment: the switch might be short in memory or some other component might be unable to provide the necessary information to fcdomain.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-2-MY_NON_VIRTUAL_DOM_CONFLICTS Format: During VSAN merge detected 
that the local switch has the same domain ID %d and WWN %s of another switch 

Explanation    The system has detected that the local switch has the same domain ID [dec] and WWN [chars] of another switch.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-2-NON_VIRTUAL_DOMS_CONFLICTS Format: During VSAN merge detected 
conflict between two switches having the same non-virtual domain ID %d and the 
same WWN %s 

Explanation    The system has detected that two switches have the same non-virtual domain ID [dec] and the same WWN [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-2-SYSBIND_FAILED Format: Bind to System Manager service failed 

Explanation    fcdomain has not been able to contact the The system Manager.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-2-SYSMGR_INITIALIZATION_FAILED Format: System Manager 
initialization sequence failed 

Explanation    The fcdomain has not been able to complete the initialization sequence with the The system Manager. fcdomain depends on resources not available at the moment: the switch might be short in memory or some other component might be unable to provide the necessary information to fcdomain.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DM-3

Error Message     DM-3-COMMITERRORLOCALINVALIDALLOWEDDOMS Format: A remote switch 
attempted to locally apply an illicit allowed domains configuration 

Explanation    A remote switch attempted to locally apply an allowed domain's configuration that does not include all currently assigned domains or the locally configured domain.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-3-SDWRAPBIND_FAILED Format: Bind to debug server failed 

Explanation    fcdomain feature has not been able to contact the debug service. Any problems occurring in the fcdomain feature will not be logged.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-3-SDWRAPHISTINIT_FAILED Format: Initialization of history message 
list failed. 

Explanation    fcdomain feature has not been able to contact the debug history service. Any problems occurring in the fcdomain feature will not be logged to this debug history.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DM-4

Error Message     DM-4-ALLOWED_DM_LIST_MOD_ON_SUBORDINATE Format: Allowed domain list 
for vsan %d modified on subordinate switch with fcdomain distribution enabled 

Explanation    When distRIBution is enabled, it is recommended to modify the allow domain list on the principal switch only.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-4-FC2_CORRUPTED Format: Received malformed FC2 %s frame 

Explanation    fcdomain received a malformed FC2-SWILS frame.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-4-FCID_PERSISTENT_TBL_ALMOST_FULL Format: FCID persistent table is 
almost full 

Explanation    fcdomain has 80% or more of the FCID persistent table full with entries. Perform [show fcdomain fcid persistent VSAN <vsan-id>] to view the entries currently in the table.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DM-5

Error Message     DM-5-DOMAIN_TYPE_IS_PREFERRED Format: The domain ID type is currently 
configured as preferred in all the existing VSANs 

Explanation    All the currently existing VSANs have the domain ID type configured as preferrored. This means that with a low probability the domain ID of the local VSAN might change afer a reconfiguration. A reconfiguration can happen when two or more VSANs are merged or a principal link flaps. A principal link is either an upstream or a downstream link.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-5-FCID_PERSISTENT_TBL_HALF_FULL Format: FCID persistent table is 
half full 

Explanation    fcdomain has 50% of the FCID persistent table full with entries. Perform [show fcdomain fcid persistent VSAN <vsan-id>] to view the entries currently in the table.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-5-FCIDP_DISABLED Format: FCID persistency feature is currently not 
enabled in any of the existing VSANs 

Explanation    All the currently existing VSANs have the FCID persistency feature disabled.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-5-UNKNOWNDOMAININCFSDATAREQUEST Format: Received CFS Data request 
from unknown domain %d. 

Explanation    A CFS Data request from the unknown domain [dec] has been received.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-5-UNKNOWNDOMAININCFSLOCKREQUEST Format: Received CFS Lock request 
from unknown domain %d. 

Explanation    A CFS Lock request from the unknown domain [dec] has been received.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-5-UNKNOWNDOMAININCFSRELEASEREQUEST Format: Received CFS Release 
request from unknown domain %d. 

Explanation    A CFS Release request from the unknown domain [dec] has been received.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-5-UNKNOWNDOMAININUNKNOWNCFSREQUEST Format: Received CFS request 
from unknown domain %d. 

Explanation    A CFS request from the unknown domain [dec] has been received.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DM-6

Error Message     DM-6-BF_STARTED Format: BF started by %s 

Explanation    Build Fabric has been started in this VSAN.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-CANNOTFREESINGLEFCID Format: Impossible to free single FCIDs 

Explanation    Impossible to free single FCIDs.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-CLEARLOCKNOTIFICATIONRECEIVED Format: Implict lock release. 

Explanation    Lock has been implicitly released due to a clear session operation.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-DOMAINID_INVALID Format: Local domain ID invalid 

Explanation    The local domain ID is invalid.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-DOMAINID_VALID Format: Local domain ID %d available 

Explanation    The domain ID [dec] is available.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-DOWNSTREAM_SWITCHED Format: Downstream interface has been 
fast-switched from %s to %s 

Explanation    Because of a link failure the downstream interface has been fast-switched from [dec] to [dec].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-EPORT_ALREADY_CREATED Format: Interface %s already created 

Explanation    Interface [chars] already created.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-EPORT_ALREADY_DOWN Format: Interface %s is already down 

Explanation    Interface [chars] already down.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-EPORT_CLEANUP Format: Interface %s received cleanup request 

Explanation    fcdomain on interface [chars] has received a cleanup request.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-EPORT_CREATED Format: Creation of interface %s 

Explanation    fcdomain is going to create interface [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-EPORT_DOWN Format: Interface %s is down 

Explanation    fcdomain is going to remove interface [chars] from its database.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-FABRICNAME_INVALID Format: Fabric name not available 

Explanation    Fabric name not available.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-FABRICNAME_VALID Format: Fabric name %s available 

Explanation    Fabric name [chars] available.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-FCID_ASSIGNED Format: Assigned single FCID %02x:%02x:%02x 

Explanation    Assigned single FCID [hex]:[hex]:[hex].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-FCID_FREED Format: Freed single FCID %02x:%02x:%02x 

Explanation    Freed single FCID [hex]:[hex]:[hex].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-FCIDALREADYFREE Format: FCIDs already free 

Explanation    FCIDs already free.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-FCIDNOTSTORED Format: FCIDs not stored 

Explanation    FCIDs not stored.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-FCIDP_ENABLED_DOM_TYPE_PREFERRED Format: FCID persistency is 
enabled 

Explanation    The FCID persistency feature is enabled, but the domain ID type is configured as preferrored. This means that with a low probability the domain ID of the local VSAN might change afer a reconfiguration. A reconfiguration can happen when two or more VSANs are merged or a principal link flaps. A principal link is either an upstream or a downstream link. Should the domain ID change, all the FCIDs associated with it would be invalidated.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-FCIDS_ASSIGNED Format: Assigned a sequence of 256 contiguous 
FCIDs starting from FCID %02x:%02x:%02x 

Explanation    Assigned a sequence of 256 contiguous FCIDs starting from FCID [hex]:[hex]:[hex].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-FCIDS_FREED Format: Freed a sequence of 256 contiguous FCIDs 
starting from FCID %02x:%02x:%02x 

Explanation    Freed a sequence of 256 contiguous FCIDs starting from FCID [hex]:[hex]:[hex].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-INCORRECTDOMAIN Format: Requested FCIDs with domain field 
different from local domain 

Explanation    Requested FCIDs with domain field different from local domain.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-INCORRECTDOMAINRANGE Format: Requested FCIDs with domain field 
not in expected range 

Explanation    Requested FCIDs with domain field not in expected range.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-INVALIDARG Format: Requested FCID of type 00.00.YY 

Explanation    Requested FCID of type 00.00.YY, but specifying an entire area.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-NODOMAIN Format: Local domain not available 

Explanation    The local domain is not available yet.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-NOFREEFCID Format: No free FCIDs 

Explanation    No free FCIDs.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-OTHER_SIDE_VIRTUAL_IVR_DOMS_OVERLAPPING Format: During VSAN 
merge detected overlap with virtual IVR domain ID %d from across the link 

Explanation    The system has detected an overlap with the virtual IVR domain ID [dec] from across the link during an attempt to merge the local VSAN.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-PSWSSTARTED Format: Principal Switch Selection started 

Explanation    fcdomain started a principal switch selection phase to elect a principal switch in this VSAN.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-RCF_STARTED Format: RCF started by %s 

Explanation    Reconfigure Fabric has been started in this VSAN.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-REQSINGLEFCIDWITHINRESERVEDRANGE Format: Requested single FCIDs 
in area %d within the reserved range 

Explanation    Requested single FCIDs in area [dec] within the reserved range.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-REQUESTEDFCIDNOTFREE Format: Requested FCIDs not free 

Explanation    Requested FCIDs not free.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-REQUESTEDFCIDRESERVED Format: Requested reserved FCIDs 

Explanation    Requested reserved FCIDs.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-REQUESTEDRESERVEDFCIDMISMATCH Format: Requested persistent FCIDs 

Explanation    Requested persistent FCIDs, but there is a mismatch.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-SAME_WWNS_DIFFERENT_DOMS_CONFLICTS Format: During VSAN merge 
detected two switches with same WWN %s and different non-virtual domain IDs %d and 
%d 

Explanation    The system has detected that two switches have the same WWN [chars], but different non-virtual domain IDs: [dec] and [dec].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-TIMER_UNKNOWN Format: fcdomain has received a notification for 
an unknown timer expiration 

Explanation    A timer unknown to fcdomain has expired.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-UPSTREAM_SWITCHED Format: Upstream interface has been 
fast-switched from %s to %s 

Explanation    Because of a link failure the upstream interface has been fast-switched from [dec] to [dec].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-UUIDNOSPACEFOUND Format: No available space to store the identity 
of the requestor the FCIDs 

Explanation    No available space to store the identity of the requestor the FCIDs.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-6-VIRTUAL_IVR_DOMS_OVERLAPPING Format: During VSAN merge detected 
overlap with local virtual IVR domain ID %d 

Explanation    The system has detected an overlap with the local virtual IVR domain ID [dec] during an attempt to merge the local VSAN.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DM-7

Error Message     DM-7-EPORT_ALREADY_ISOLATED Format: Interface %s is already isolated 
or down 

Explanation    fcdomain was going to isolate interface [chars], but the interface is already isolated.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-7-FCID_IN_USE_PURGING_FOR_FICON_MGR Format: FICON needs to purge 
the persistent FCID table 

Explanation    There may be a problem in the sequence that shuts down all interfaces before fcdomain receives a request from FICON Manager to purge the persistent FCID table.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-7-FSM_FORBIDDEN_TRANSITION Format: fcdomain state machine has hit 
a forbidden transition 

Explanation    fcdomain state machine has tried to execute a forbidden transition.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-7-INTERFACERDY Format: Interface %s ready 

Explanation    Interface [chars] is ready.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DM-7-PREACTIONTYPE_UNKNOWN Format: fcdomain state machine has hit an 
unknown pre-action type 

Explanation    An undefined pre-action type has been used.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DMM-SLOT# Messages

This section contains the DMM-SLOT# messages.

DMM-SLOT#-5

Error Message     DMM-SLOT#-5-LOG_ERR_DMM_NEW_NPORT_SRVR_ZONE: Job Id:%Ld VSAN :[dec] 
New N-Port FCID :[hex] Server FCID:[hex] are in the same zone. ALERT!!

Explanation    A New N-Port has come up which is zoned in the same zone as the Server.

Recommended Action    No action is required.

Error Message     DMM-SLOT#-5-LOG_ERR_DMM_NEW_NPORT_STG_ZONE: Job Id:%Ld VSAN :[dec] 
New N-Port FCID :[hex] Storage FCID:[hex] are in the same zone. ALERT!!

Explanation    A New N-Port has come up which is zoned in the same zone as the Storage.

Recommended Action    No action is required.

Error Message     DMM-SLOT#-5-LOG_ERR_DMM_SRVR_RSCN: Job Id:%Ld Server N-Port 
pWWN:0x%Lx [chars] 

Explanation    An RSCN event was received for the Server associated with a Job.

Recommended Action    No action is required.

Error Message     DMM-SLOT#-5-LOG_ERR_DMM_STG_RSCN: Job Id:%Ld N-Port pWWN:0x%Lx 
Storage:[chars] [chars]

Explanation    An RSCN event was received for the Storage associated with a Job.

Recommended Action    No action is required.

Error Message     DMM-SLOT#-5-LOG_EV_DMM_JOB_COMPLETE: Job Id:%Ld NumSession:[dec] 

Explanation    Event indicating the completion of a Data Migration Job.

Recommended Action    No action is required.

Error Message     DMM-SLOT#-5-LOG_EV_DMM_JOB_ERROR: Job Id:%Ld NumSession:[dec] 

Explanation    Event indicating the Suspension of Data Migration Job.

Recommended Action    No action is required.

Error Message     DMM-SLOT#-5-LOG_EV_DMM_JOB_ERROR_LOST_SSM_PEER_CONNECTION: Job 
Id:%Ld NumSession:[dec] 

Explanation    Event indicating the Suspension of Data Migration Job due to loss in ip connectivity to peer ssm.

Recommended Action    No action is required.

Error Message     DMM-SLOT#-5-LOG_EV_DMM_JOB_FINISH: Job Id:%Ld NumSession:[dec] 

Explanation    Event indicating Finish-request for a Method-2 Data Migration Job.

Recommended Action    No action is required.

Error Message     DMM-SLOT#-5-LOG_EV_DMM_JOB_START: Job Id:%Ld NumSession:[dec] 

Explanation    Event indicating the start of a Data Migration Job.

Recommended Action    No action is required.

Error Message     DMM-SLOT#-5-LOG_EV_DMM_JOB_STOP: Job Id:%Ld NumSession:[dec] 

Explanation    Event indicating that the Data Migration Job was stopped by Administrator.

Recommended Action    No action is required.

Error Message     DMM-SLOT#-5-LOG_EV_DMM_JOB_TCP_CONNECTION_DOWN: Job Id:%Ld lost 
connection to peer [chars]. Job may be RESET 

Explanation    Event indicating IP Connectivity loss to peer SSM. Affected Job may be RESET.

Recommended Action    No action is required.

Error Message     DMM-SLOT#-5-LOG_EV_DMM_JOB_VERIFY_COMPLETE: Job Id:%Ld 
NumSession:[dec] 

Explanation    Event indicating the completion of a Data Migration Job Verification.

Recommended Action    No action is required.

Error Message     DMM-SLOT#-5-LOG_EV_DMM_JOB_VERIFY_ERROR: Job Id:%Ld NumSession:[dec] 

Explanation    Event indicating the Suspension of Data Migration Job Verification due to an error.

Recommended Action    No action is required.

Error Message     DMM-SLOT#-5-LOG_EV_DMM_JOB_VERIFY_START: Job Id:%Ld NumSession:[dec] 

Explanation    Event indicating the start of a Data Migration Job Verification.

Recommended Action    No action is required.

Error Message     DMM-SLOT#-5-LOG_EV_DMM_JOB_VERIFY_STOP: Job Id:%Ld NumSession:[dec] 

Explanation    Event indicating the Suspension of Data Migration Job Verification by the user.

Recommended Action    No action is required.

DOT1X Messages

This section contains the DOT1X messages.

DOT1X-2

Error Message     DOT1X-2-DOT1X_INIT: Dot1x unable to start 

Explanation    The system failed to create the Dot1x process.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-2-INIT Format: Dot1x unable to start 

Explanation    The system failed to create the Dot1x process.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DOT1X-3

Error Message     DOT1X-3-ERR_SPANDST Format: Dot1x can not be enabled on %s. It is 
configured as a SPAN Dest port. 

Explanation    Dot1x and SPAN Dest ports are mutually exclusive features.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-3-ERR_SPANDST: It is configured as a SPAN Dest port. 

Explanation    Dot1x and SPAN Dest ports are mutually exclusive features.

Recommended Action    Disable SPAN destination port configuration first before reconfiguring Dot1x on the port.

Error Message     DOT1X-3-INVALID_INPUT Format: Dot1x Interface parameter is Invalid on 
interface %s. 

Explanation    The Dot1x interface parameter is out of the specified range or is invalid.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-3-INVALID_INPUT: Invalid on interface [chars]. 

Explanation    The Dot1x interface parameter is out of the specified range or is invalid.

Recommended Action    Refer to the CLI help documentation to determine the valid 802.1x parameters.

Error Message     DOT1X-3-MEM_UNAVAIL Format: Memory was not available to perform the 
802.1X action. 

Explanation    Insufficient system memory is available to perform the Dot1x Authentication.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-3-MEM_UNAVAIL: perform the 802.1X action. 

Explanation    Insufficient system memory is available to perform the Dot1x Authentication.

Recommended Action    Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.

Error Message     DOT1X-3-NOT_DOT1X_CAPABLE Format: Dot1x disabled on interface %s 
because it is not a physical Ethernet interface. 

Explanation    Dot1x Authentication can only be enabled on physical Ethernet interfaces.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-3-NOT_DOT1X_CAPABLE: interface [chars] because it is not a 
physical Ethernet interface. 

Explanation    Dot1x Authentication can only be enabled on physical Ethernet interfaces.

Recommended Action    Enable Dot1x Authentication on physical Ethernet interfaces only.

Error Message     DOT1X-3-SECURITY_VIOLATION Format: Security violation New MAC address 
%s is seen on interface %s in %s mode 

Explanation    The port on the interface specified in the error message is configured in single host mode. Any new host that is detected on the interface is treated as a security violation. The port has been Error disabled.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-3-SECURITY_VIOLATION: New MAC address [chars] is seen on 
interface [chars] in [chars] mode 

Explanation    The port on the interface specified in the error message is configured in single host mode. Any new host that is detected on the interface is treated as a security violation. The port has been Error disabled.

Recommended Action    Ensure that the port is configured to use only one host. Enter the <Cmd>shutdown<Cmd> followed by <CmdBold>no shutdown<CmdBold> command to restart the port.

Error Message     DOT1X-3-SM_INIT Format: Internal error while initializing state 
machine %s 

Explanation    An attempt was made to initialize an invalid state machine.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-3-SM_INIT: Internal error while initializing state machine 
[chars], state [chars]: [chars] 

Explanation    An attempt was made to initialize an invalid state machine.

Recommended Action    Initialize dot1x state machine.

DOT1X-4

Error Message     DOT1X-4-BADEVENT Format: Event %s is invalid for the current state 
%s: %s %s 

Explanation    An attempt was made to post an event to a state machine that is invalid for the current state.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-4-BADEVENT: Event [chars] is invalid for the current state 
[chars]: [chars] [chars] 

Explanation    An attempt was made to post an event to a state machine that is invalid for the current state.

Recommended Action    Initialize dot1x state machine.

Error Message     DOT1X-4-MAB_DISABLED Format: Interface %s is in Trunk mode 

Explanation    MAB is not supported on Trunk port.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-4-MAB_DISABLED: Interface [chars] is in Trunk mode, MAB is not 
supported on this port 

Explanation    MAB is not supported on Trunk port.

Recommended Action    To enable MAB make sure that port is not in trunk mode.

Error Message     DOT1X-4-MAB_DISABLED_ON_PCM Format: Interface %s is a member of 
portchannel 

Explanation    MAB is not supported on port channel member port.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-4-MAB_DISABLED_ON_PCM: Interface [chars] is a member of 
portchannel, MAB is not supported on this port 

Explanation    MAB is not supported on port channel member port.

Recommended Action    To enable MAB make sure that port is not member of port channel.

Error Message     DOT1X-4-MULTIHOST_ON_PCM Format: Interface %s is a member of 
portchannel 

Explanation    Current Port is a member of port channel, so dot1x host mode has to be in multi-host mode.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-4-MULTIHOST_ON_PCM: Interface [chars] is a member of 
portchannel, dot1x host mode will be multi-host and changing it to single-host 
mode won't be supported

Explanation    Current Port is a member of port channel, so dot1x host mode has to be in multi-host mode.

Recommended Action    To change host mode, ensure that port is not a member of port channel.

Error Message     DOT1X-4-PSEC_ON_PCM Format: Interface %s is a member port or 
portchannel interface with port security configration 

Explanation    Dot1x is not supported on member ports or port channel with port security configuration.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-4-PSEC_ON_PCM: Interface [chars] is a member port or portchannel 
interface with port security configration 

Explanation    Dot1x is not supported on member ports or port channel with port security configuration.

Recommended Action    Remove port security configuration on the member port or port channel interface.

Error Message     DOT1X-4-STOPPED Format: Event %s ignored because the state machine is 
stopped: %s %s 

Explanation    An attempt was made to post an event to a state machine that has already been stopped.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-4-STOPPED: Event [chars] ignored because the state machine is 
stopped: [chars] [chars] 

Explanation    An attempt was made to post an event to a state machine that has already been stopped.

Recommended Action    An internal error has occurred with the state machine. The traceback should indicate the guilty party.

Error Message     DOT1X-4-TO_MULTIHOST Format: Interface %s is in trunk mode 

Explanation    Current Port is in trunk mode, so dot1x host mode has to be in multi-host mode.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-4-TO_MULTIHOST: Interface [chars] is in trunk mode, dot1x host 
mode will be multi-host and changing it to single-host mode won't be supported

Explanation    Current Port is in trunk mode, so dot1x host mode has to be in multi-host mode.

Recommended Action    To change host mode, ensure that port is not in trunk mode.

DOT1X-5

Error Message     DOT1X-5-DISABLED Format: dot1x Disabled 

Explanation    dot1x Service Disabled.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-5-DISABLED_LIC_EXPIRED Format: Dot1x Disabled due to License 
Expiry 

Explanation    Dot1x Disabled due to License Expiry.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-5-DOT1X_DISABLED: dot1x Disabled 

Explanation    Dot1x Service Disabled.

Recommended Action    No action is required.

Error Message     DOT1X-5-DOT1X_ENABLED: dot1x Enabled 

Explanation    Dot1x Service Enabled.

Recommended Action    No action is required.

Error Message     DOT1X-5-DOT1X_NOTIF: [chars] 

Explanation    Dot1x Notification.

Recommended Action    No action is required.

Error Message     DOT1X-5-ENABLED Format: dot1x Enabled 

Explanation    dot1x Service Enabled.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-5-INVALID_EAPOL: packet body length [dec] interface [chars] MTU 
[dec] 

Explanation    802.1X received invalid EAPOL packet.

Recommended Action    Verify source of EAPOL packets.

Error Message     DOT1X-5-INVALID_MAC: broadcast or multicast mac address) [chars] is 
trying to authenticate. 

Explanation    Authentication using 802.1x is not allowed for zero, broadcast, and multicast source MAC addresses.

Recommended Action    Connect a Dot1x supported Host to the Dot1x enabled port.

Error Message     DOT1X-5-NOTIF Format: %s 

Explanation    Dot1x Notification.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-5-PAC_STATUS Format: PAC provisioning for the server %s through 
the vrf %s %s 

Explanation    PAC provisioning status.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-5-PAC_STATUS: PAC provisioning for the server [chars] through 
the vrf [chars] [chars] 

Explanation    PAC provisioning status.

Recommended Action    No action is required.

Error Message     DOT1X-5-SECURITY_VIOLATION: New MAC address [chars] is seen on 
interface [chars] in [chars] mode 

Explanation    The port on the interface specified in the error message is configured in single host mode. Any new host that is detected on the interface is treated as a security violation. The port has been Error disabled.

Recommended Action    Ensure that the port is configured to use only one host. Enter the <Cmd>shutdown<Cmd> followed by <CmdBold>no shutdown<CmdBold> command to restart the port.

Error Message     DOT1X-5-SESSION_CREATION Format: Dot1x authentication session 
initiated in interface %s using authentication method %s 

Explanation    Dot1x authentication session has been created after successful authentication of supplicannot.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-5-SESSION_CREATION: Dot1x authentication session initiated in 
interface [chars] using authentication method [chars]

Explanation    Dot1x authentication session has been created after successful authentication of supplicannot.

Recommended Action    No action is required.

Error Message     DOT1X-5-SESSION_TERMINATION Format: Dot1x authentication session in 
interface %s using authentication method %s is terminated because of %s and port 
moved to %s state 

Explanation    Dot1x authentication session has been terminated.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-5-SESSION_TERMINATION: Dot1x authentication session in 
interface [chars] using authentication method [chars] is terminated because of 
[chars] and port moved to [chars] state

Explanation    Dot1x authentication session has been terminated.

Recommended Action    No action is required.

Error Message     DOT1X-5-STATUS Format: Dot1x interface %s status changed from %s to %s 

Explanation    Dot1x authenticator has changed its internal state.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DOT1X-5-STATUS: Dot1x interface [chars] status changed from [chars] 
to [chars] 

Explanation    Dot1x authenticator has changed its internal state.

Recommended Action    No action is required.

DPP_DEBUG Messages

This section contains the DPP_DEBUG messages.

DPP_DEBUG-2

Error Message     DPP_DEBUG-2-DPP_CRIT Format: [DPP%d] %s 

Explanation    a DPP generated a critical message.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DPP_DEBUG-2-DPP_CRIT: [DPP[dec]] [chars] 

Explanation    A DPP generated a critical message.

Recommended Action    No action is required.

DPVM Messages

This section contains the DPVM messages.

DPVM-2

Error Message     DPVM-2-ALLOC_FAILED Format: Memory allocation failed for size:%d for 
%s 

Explanation    memory allocation failed for size [dec] for [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DPVM-2-ALLOC_FAILED: Memory allocation failed for size:[dec] for 
[chars] 

Explanation    Memory allocation failed for size [dec] for [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DPVM-2-DPVM_DUPL_REJECT: [chars] 

Explanation    Rejected duplicate pwwn query.

Recommended Action    Dpvm overwrite-duplicate-pwwn.

Error Message     DPVM-2-DUPL_REJECT Format: %s 

Explanation    Rejected duplicate pwwn query.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DPVM-3

Error Message     DPVM-3-DB_ERR Format: %s 

Explanation    an error occurred during an DPVM database operation. [chars] indicates the reason for the error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DPVM-3-DB_ERR: [chars] 

Explanation    An error occurred during an DPVM database operation. [chars] indicates the reason for the error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DPVM-3-DDAS_MODE_INVALID Format: %s 

Explanation    DDAS mode Invalid. [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DPVM-3-DDAS_MODE_INVALID: [chars] 

Explanation    DDAS mode Invalid. [chars].

Recommended Action    Flip DDAS mode.

Error Message     DPVM-3-INIT_FAIL Format: %s 

Explanation    an error occurred during DPVM Initialization. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DPVM-3-INIT_FAIL: [chars] 

Explanation    An error occurred during DPVM Initialization. [chars] indicates the reason for failure.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DPVM-3-MTS_ERR Format: %s 

Explanation    an error occurred in processing of an MTS message. [chars] indicates the error that occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DPVM-3-MTS_ERR: [chars] 

Explanation    An error occurred in processing of an MTS message. [chars] indicates the error that occurred.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DPVM-3-PSS_ERR Format: %s 

Explanation    an error occurred during an DPVM PSS operation. [chars] indicates the PSS operation that caused the error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DPVM-3-PSS_ERR: [chars] 

Explanation    An error occurred during an DPVM PSS operation. [chars] indicates the PSS operation that caused the error.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DPVM-4

Error Message     DPVM-4-ACTIVATION_FAIL Format: %s 

Explanation    Activation of DPVM device mappings failed due to [chars].

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DPVM-4-ACTIVATION_FAIL: [chars] 

Explanation    Activation of DPVM device mappings failed due to [chars].

Recommended Action    Correct the error and reactivate database again.

Error Message     DPVM-4-FEATURE_DISABLED Format: %s 

Explanation    DPVM is unavailable and disabled now.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DPVM-4-FEATURE_DISABLED: [chars] 

Explanation    DPVM is unavailable and disabled now.

Recommended Action    No action is required.

DPVM-6

Error Message     DPVM-6-FEATURE_ENABLED Format: %s 

Explanation    DPVM is available and enabled now.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DPVM-6-FEATURE_ENABLED: [chars] 

Explanation    DPVM is available and enabled now.

Recommended Action    No action is required.

Error Message     DPVM-6-INFO Format: %s 

Explanation    an event happened that affects DPVM. [chars] indicates the event.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DPVM-6-INFO: [chars] 

Explanation    An event happened that affects DPVM. [chars] indicates the event.

Recommended Action    No action is required.

DRAP Messages

This section contains the DRAP messages.

DRAP-2

Error Message     DRAP-2-DRAP_LINK_BRINGUP_STALLED_STATIC: Link bringup stalled due to 
conflicts 

Explanation    Interface is disabled due to conflicts.

Recommended Action    No action is required.

Error Message     DRAP-2-LINK_BRINGUP_STALLED_STATIC Format: Link bringup stalled due 
to conflicts 

Explanation    Interface is disabled due to conflicts.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DRAP-4

Error Message     DRAP-4-DRAP_INVALID_FTAG: Invalid ftag [dec] received 

Explanation    Invalid ftag is received from remote.

Recommended Action    No action is required.

Error Message     DRAP-4-DRAP_INVALID_SWITCH_ID: Invalid switch-id [dec] received 

Explanation    Invalid switch-id is received from remote.

Recommended Action    No action is required.

Error Message     DRAP-4-DRAP_LINK_BRINGUP_STALLED: Link bringup stalled due to 
conflicts 

Explanation    Interface is disabled due to conflicts.

Recommended Action    No action is required.

Error Message     DRAP-4-INVALID_FTAG Format: Invalid ftag %d received 

Explanation    Invalid ftag is received from remote.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DRAP-4-INVALID_SWITCH_ID Format: Invalid switch-id %d received 

Explanation    Invalid switch-id is received from remote.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

DRAP-6

Error Message     DRAP-6-DRAP_LINK_BRINGUP_RESOLVE_COLLISION: Resolving Collision for 
switch-id [dec] 

Explanation    Resolving Collision for switch-id.

Recommended Action    No action is required.

Error Message     DRAP-6-DRAP_LINK_BRINGUP_STALLED: LINK bringup suspended for [dec] 
due to conflicts 

Explanation    Link bring up temporarily suspended due to conflicts.

Recommended Action    No action is required.

Error Message     DRAP-6-DRAP_LINK_BRINGUP_STALLED_CLEARED: LINK bringup cleared for 
[dec] after collision resolution 

Explanation    Link bring up temporarily suspended due to conflicts.

Recommended Action    No action is required.

Error Message     DRAP-6-DRAP_NEW_ES_SWITCH_ID: New Emulated switch-id [chars] received 

Explanation    New Emulated switch-id received.

Recommended Action    No action is required.

Error Message     DRAP-6-DRAP_NEW_SWITCH_ID: New switch-id [chars] received 

Explanation    New switch-id received.

Recommended Action    No action is required.

Error Message     DRAP-6-DRAP_SWID_CHANGED: Switch-id [dec] is assigned with [chars] 
state 

Explanation    Local switch-id is changed.

Recommended Action    No action is required.

Error Message     DRAP-6-DRAP_SWID_CONFLICTS: Switch-id [dec] is in conflict with 
device [chars] 

Explanation    Local switch-id collision with other device.

Recommended Action    No action is required.

Error Message     DRAP-6-DRAP_SWID_PRI_SEC_CHANGED: Switch-id [dec] is changed to 
[chars] 

Explanation    Local switch-id status changed.

Recommended Action    No action is required.

Error Message     DRAP-6-DRAP_SWID_STATE_CHANGED: Switch-id [dec] status changed to 
[chars] 

Explanation    Local switch-id status changed.

Recommended Action    No action is required.

Error Message     DRAP-6-LINK_BRINGUP_RESOLVE_COLLISION Format: Resolving Collision for 
switch-id %d 

Explanation    Resolving Collision for switch-id.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DRAP-6-LINK_BRINGUP_STALLED Format: LINK bringup suspended for %d due 
to conflicts 

Explanation    Link bring up temporarily suspended due to conflicts.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DRAP-6-LINK_BRINGUP_STALLED_CLEARED Format: LINK bringup cleared for 
%d after collision resolution 

Explanation    Link bring up temporarily suspended due to conflicts.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DRAP-6-NEW_ES_SWITCH_ID Format: New Emulated switch-id %s received 

Explanation    New Emulated switch-id received.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DRAP-6-NEW_SWITCH_ID Format: New switch-id %s received 

Explanation    New switch-id received.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DRAP-6-SWID_CHANGED Format: Switch-id %d is assigned with %s state 

Explanation    Local switch-id is changed.

Recommended Action    Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.

Error Message     DRAP-6-SWID_CONFLICTS Format: Switch-id %d is in conflict with device 
%s 

Explanation    Local switch-id collision with other device.