Cisco Nexus 5000 Series Command Reference
System Management Commands
Downloads: This chapterpdf (PDF - 240.0KB) The complete bookPDF (PDF - 3.14MB) | Feedback

System Management Commands

Table Of Contents

System Management Commands

clear logging nvram

clear logging onboard

clear logging session

clear ntp session

clear ntp statistics

logging console

logging event

logging event port

logging level

logging logfile

logging module

logging monitor

logging server

logging timestamp

ntp

ntp abort

ntp commit

ntp distribute

ntp sync-retry

show logging console

show logging info

show logging last

show logging level

show logging logfile

show logging module

show logging monitor

show logging nvram

show logging onboard

show logging server

show logging session status

show logging status

show logging timestamp

show ntp peer-status

show ntp peers

show ntp statistics

show ntp timestamp-status

System Message Logging Facilities


System Management Commands


This chapter describes the system management commands available on Cisco Nexus 5000 Series switches.

clear logging nvram

Use the clear logging nvram command to clear the NVRAM logs.

clear logging nvram

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to clear the NVRAM logs:

switch# clear logging nvram  

Related Commands

Command
Description

show logging nvram

Displays the NVRAM logs.


clear logging onboard

To clear the OBFL entries in the persistent log, use the clear logging onboard command.

clear logging onboard [environmental-history] [exception-log] [obfl-log] [stack-trace]

Syntax Description

environmental-history

(Optional) Clears the OBFL environmental history.

exception-log

(Optional) Clears the OBFL exception log entries.

obfl-log

(Optional) Clears the OBFL (boot-uptime/device-version/obfl-history).

stack-trace

(Optional) Clears the OBFL stack trace entries.


Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

The following example shows how to clear the OBFL environmental history entries:

switch# clear logging onboard environmental-history  

The following example shows how to clear the OBFL exception-log entries:

switch# clear logging onboard exception-log  

The following example shows how to clear the OBFL (boot-uptime/device-version/obfl-history) entries:

switch# clear logging onboard obfl-log  

The following example shows how to clear the OBFL stack trace entries:

switch# clear logging onboard stack-trace  

Related Commands

Command
Description

show logging onboard

Displays onboard failure logs.


clear logging session

Use the clear logging session command to clear the current logging session.

clear logging session

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to clear the current logging session:

switch# clear logging session  

Related Commands

Command
Description

show logging session

Displays logging session status.


clear ntp session

To clear the Network Time Protocol (NTP) session, use the clear ntp session command.

clear ntp session

Syntax Description

This command has no other arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

The following example shows how to discard the NTP CFS distribution session in progress:

switch# clear ntp session  

Related Commands

Command
Description

show ntp

Displays NTP information.


clear ntp statistics

To clear the Network Time Protocol (NTP) session, use the clear ntp session command.

clear ntp statistics {all-peers | io | local | memory}

Syntax Description

all-peers

Clears all peer transaction statistics.

io

Clears I/O statistics.

local

Clears local statistics.

memory

Clears memory statistics.


Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

The following example shows how to discard the NTP I/O statistics:

switch# clear ntp statistics io  

Related Commands

Command
Description

show ntp

Displays NTP information.


logging console

Use the logging console command to enable logging messages to the console session.

To disable logging messages to the console session, use the no form of this command.

logging console [severity-level]

no logging console

Syntax Description

severity-level

(Optional) The number of the desired severity level at which messages should be logged. Messages at or numerically lower than the specified level are logged. Severity levels are as follows:

0—emergency: System unusable

1—alert: Immediate action needed

2—critical: Critical condition—default level

3—error: Error condition

4—warning: Warning condition

5—notification: Normal but significant condition

6—informational: Informational message only

7—debugging: Appears during debugging only


Command Default

None

Command Modes

Configuration mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to enable logging messages with a severity level of 4 (warning) or higher to the console session:

switch# configure terminal  
switch(config)# logging console 4  

Related Commands

Command
Description

show logging console

Displays the console logging configuration.


logging event

Use the logging event command to log interface events. To disable logging of interface events, use the no form of this command.

logging event port {link-status | trunk-status} {default | enable}

no logging event port {link-status | trunk-status} {default | enable}

Syntax Description

link-status

Log all UP/DOWN and CHANGE messages.

trunk-status

Log all TRUNK status messages.

default

The default logging configuration is used by interfaces not explicitly configured.

enable

To enable logging overriding port level configuration.


Command Default

None

Command Modes

Configuration mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to log interface events:

switch# configure terminal  
switch(config)# logging event link-status default  

Related Commands

Command
Description

show logging

Displays the logging status.


logging event port

Use the logging event port command to log events on an interface. To disable logging of interface events, use the no form of this command.

logging event port {link-status | trunk-status} [default]

no logging event port {link-status | trunk-status}

Syntax Description

link-status

Log all UP/DOWN and CHANGE messages.

trunk-status

Log all TRUNK status messages.

default

(Optional) The default logging configuration is used by interfaces not explicitly configured.


Command Default

None

Command Modes

Interface configuration mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to log interface events:

switch# configure terminal  
switch(config)# interface ethernet 1/1 
switch(config-if)# logging event port link-status default  

Related Commands

Command
Description

show interface

Displays the interface configuration information.

show logging

Displays the logging status.


logging level

Use the logging level command to enable logging messages from the defined facility that have the specified severity level or higher.

To disable logging messages from the defined facility, use the no form of this command.

logging level facility severity-level

no logging level facility severity-level

Syntax Description

facility

Defines the appropriate facility. The facilities are listed in the "System Message Logging Facilities" section.

To apply the same severity level to all facilities, use the all facility.

severity-level

The number of the desired severity level at which messages should be logged. Messages at or numerically lower than the specified level are logged. Severity levels are as follows:

0—emergency: System unusable

1—alert: Immediate action needed

2—critical: Critical condition—default level

3—error: Error condition

4—warning: Warning condition

5—notification: Normal but significant condition

6—informational: Informational message only

7—debugging: Appears during debugging only


Command Default

None

Command Modes

Configuration mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to enable logging messages from the AAA facility that have a severity level of 2 or higher:

switch(config)# logging level aaa 2  

Related Commands

Command
Description

show logging level

Displays the facility logging level configuration.


logging logfile

Use the logging logfile command to configure the name of the log file used to store system messages and the minimum severity level to log.

To disable logging to the log file, use the no form of this command.

logging logfile logfile-name severity-level [size bytes]

no logging logfile [logfile-name severity-level [size bytes]]]

Syntax Description

logfile-name

Configure the name of the log file to be used to store system messages.

severity-level

The number of the desired severity level at which messages should be logged. Messages at or numerically lower than the specified level are logged. Severity levels are as follows:

0—emergency: System unusable

1—alert: Immediate action needed

2—critical: Critical condition—default level

3—error: Error condition

4—warning: Warning condition

5—notification: Normal but significant condition

6—informational: Informational message only

7—debugging: Appears during debugging only

size bytes

(Optional) Specifies a maximum file size. The default file size is 4194304 bytes and can be configured from 4096 to 4194304 bytes.


Command Default

None

Command Modes

Configuration mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to configure a log file called logfile to store system messages and set its severity level to 4:

switch(config)# logging logfile logfile 4  

Related Commands

Command
Description

show logging logfile

Displays the log file.


logging module

Use the logging module command to enable module log messages. Set a specified severity level or use the default.

To disable module log messages, use the no form of this command.

logging module [severity-level]

no logging module

Syntax Description

severity-level

(Optional) The number of the desired severity level at which messages should be logged. Messages at or numerically lower than the specified level are logged. Severity levels are as follows:

0—emergency: System unusable

1—alert: Immediate action needed

2—critical: Critical condition

3—error: Error condition

4—warning: Warning condition

5—notification: Normal but significant condition—default level

6—informational: Informational message only

7—debugging: Appears during debugging only


Command Default

None

Command Modes

Configuration mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to enable module log messages:

switch(config)# logging module  

Related Commands

Command
Description

show logging module

Displays the module logging status.


logging monitor

Use the logging monitor command to enable the device to log messages to the monitor (terminal line). This configuration applies to Telnet and SSH sessions.

To disable monitor log messages, use the no form of this command.

logging monitor [severity-level]

no logging monitor

Syntax Description

severity-level

(Optional) The number of the desired severity level at which messages should be logged. Messages at or numerically lower than the specified level are logged. Severity levels are as follows:

0—emergency: System unusable

1—alert: Immediate action needed

2—critical: Critical condition—default level

3—error: Error condition

4—warning: Warning condition

5—notification: Normal but significant condition

6—informational: Informational message only

7—debugging: Appears during debugging only


Command Default

None

Command Modes

Configuration mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to enable monitor log messages:

switch(config)# logging monitor  

Related Commands

Command
Description

show logging monitor

Displays the status of monitor logging.


logging server

Use the logging server command to configure a remote syslog server at the specified host name or IPv4/IPv6 address.

To disable the remote syslog server, use the no form of this command.

logging server host [severity-level] [facility {auth | authpriv | cron | daemon | ftp | kernel | local0 | local1 | local2 | local3 | local4 | local5 | local6 | local7 | lpr | mail | news | syslog | user | uucp} ]

no logging server host

Syntax Description

host

Configure the host name or IPv4/IPv6 address of the Remote Syslog Server.

severity-level

(Optional) The number of the desired severity level at which messages should be logged. Messages at or numerically lower than the specified level are logged. Severity levels are as follows:

0—emergency: System unusable

1—alert: Immediate action needed

2—critical: Critical condition—default level

3—error: Error condition

4—warning: Warning condition

5—notification: Normal but significant condition

6—informational: Informational message only

7—debugging: Appears during debugging only

facility facility

(Optional) Define the appropriate outgoing facility. The facilities are listed in the System Message Logging Facilities section.

The default outgoing facility is local7.


Command Default

The default outgoing facility is local7.

Command Modes

Configuration mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to configure a remote syslog server at a specified IPv4 address, using the default outgoing facility:

switch(config)# logging server 172.28.254.253  

This example shows how to configure a remote syslog server at a specified host name, with severity level 5 or higher:

switch(config)# logging server syslogA 5  

Related Commands

Command
Description

show logging server

Displays the configured syslog servers.


logging timestamp

Use the logging timestamp command to set the logging timestamp units. By default, the units are seconds.

To reset the logging timestamp units to the default, use the no form of this command.

logging timestamp {microseconds | milliseconds | seconds}

no logging timestamp {microseconds | milliseconds | seconds}

Syntax Description

microseconds | milliseconds | seconds

Selects the units to use for logging timestamps. The default units are seconds.


Command Default

None

Command Modes

Configuration mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to set the logging timestamp units to microseconds:

switch(config)# logging timestamp microseconds  

Related Commands

Command
Description

show logging timestamp

Displays the logging timestamp configuration.


ntp

To configure the NTP peers and servers for the switch, use the ntp command. Use the no form of this command to remove configured peers and servers.

ntp {peer hostname | server hostname} [prefer] [use-vrf vrf-name]

no ntp {peer hostname | server hostname}

Syntax Description

peer hostname

The hostname or IP address of an NTP peer.

server hostname

The hostname or IP address of the NTP server.

prefer

(Optional) Specifies this peer/server as the preferred peer/server.

use-vrf vrf-name

(Optional) Specifies the virtual routing and forwarding (VRF) used to reach this peer/server.


Command Default

None

Command Modes

Configuration mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.

4.0(1a)N1(1)

The keyword use-vrf replaces the keyword vrf. The keyword vrf is retained for backwards compatibility.


Examples

This example forms a server association with a server:

switch(config)# ntp server ntp.cisco.com  

You can specify multiple associations. This example forms a peer association with a peer:

switch(config)# ntp peer 10.20.10.0  

This example deletes an association with a peer:

switch(config)# no ntp peer 10.20.10.0  

Related Commands

Command
Description

ntp distribute

Enables CFS distribution for NTP.

show ntp

Displays NTP information.


ntp abort

To discard the Network Time Protocol (NTP) Cisco Fabric Services (CFS) distribution session in progress, use the ntp abort command.

ntp abort

Syntax Description

This command has no other arguments or keywords.

Command Default

None

Command Modes

Configuration mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

The following example shows how to discard the NTP CFS distribution session in progress:

switch(config)# ntp abort  

Related Commands

Command
Description

ntp distribute

Enables CFS distribution for NTP.

show ntp

Displays NTP information.


ntp commit

To apply the pending configuration pertaining to the Network Time Protocol (NTP) Cisco Fabric Services (CFS) distribution session in progress in the fabric, use the ntp commit command.

ntp commit

Syntax Description

This command has no other arguments or keywords.

Command Default

None

Command Modes

Configuration mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

The following example shows how to commit changes to the active NTP configuration:

switch(config)# ntp commit  

Related Commands

Command
Description

ntp distribute

Enables CFS distribution for NTP.

show ntp

Displays NTP information.


ntp distribute

To enable Cisco Fabric Services (CFS) distribution for Network Time Protocol (NTP), use the ntp distribute command. To disable this feature, use the no form of the command.

ntp distribute

no ntp distribute

Syntax Description

This command has no other arguments or keywords.

Command Default

Disabled.

Command Modes

Configuration mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Usage Guidelines

Before distributing the Fibre Channel timer changes to the fabric, the temporary changes to the configuration must be committed to the active configuration using the ntp commit command.

Examples

The following example shows how to distribute the active NTP configuration to the fabric:

switch(config)# ntp distribute  

Related Commands

Command
Description

ntp commit

Commits the NTP configuration changes to the active configuration.

show ntp

Displays NTP information.


ntp sync-retry

To retry synchronization with the configured NTP servers, use the ntp sync-retry command.

ntp sync-retry

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

The following example shows how to retry synchronization with the configured NTP servers:

switch# ntp sync-retry  

Related Commands

Command
Description

ntp distribute

Enables CFS distribution for NTP.

show ntp

Displays NTP information.


show logging console

Use the show logging console command to display the console logging configuration.

show logging console

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to display the console logging configuration:

switch# show logging console  

Related Commands

Command
Description

logging console

Configures logging to the console.


show logging info

Use the show logging info command to display the logging configuration.

show logging info

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to display the logging configuration:

switch# show logging info  

show logging last

Use the show logging last command to display the last number of lines of the logfile.

show logging last number

Syntax Description

number

Enters the number of lines to display from 1 to 9999.


Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to display the last 42 lines of the log file:

switch# show logging last 42  

show logging level

Use the show logging level command to display the facility logging severity level configuration.

show logging level [facility]

Syntax Description

facility

(Optional) Defines the appropriate logging facility. The facilities are listed in the System Message Logging Facilities section.


Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to display the EtherChannel logging severity level configuration:

switch# show logging level port-channel  

Related Commands

Command
Description

logging level

Configures the facility logging level.


show logging logfile

Use the show logging logfile command to display the messages in the log file that were timestamped within the span entered. If you do not enter an end time, the current time is used.

show logging logfile [start-time yyyy mmm dd hh:mm:ss] [end-time yyyy mmm dd hh:mm:ss]

Syntax Description

start-time

(Optional) Enter a start time in the format yyyy mmm dd hh:mm:ss. Use three characters for the month (mmm) field, digits for the year (yyyy) and day (dd) fields, and digits separated by colons for the time (hh:mm:ss) field.

end-time

(Optional) Enter an end time in the format yyyy mmm dd hh:mm:ss. Use three characters for the month (mmm) field, digits for the year (yyyy) and day (dd) fields, and digits separated by colons for the time (hh:mm:ss) field.


Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to display the messages in the log file that were timestamped within the span shown:

switch# show logging logfile start-time 2008 mar 11 12:10:00  

Related Commands

Command
Description

logging logfile

Configures logging to a log file.


show logging module

Use the show logging module command to display the module logging configuration.

show logging module

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to display the module logging configuration:

switch# show logging module  

Related Commands

Command
Description

logging module

Configures module logging.


show logging monitor

Use the show logging monitor command to display the monitor logging configuration.

show logging monitor

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to display the monitor logging configuration:

switch# show logging monitor  

Related Commands

Command
Description

logging monitor

Configures logging on the monitor.


show logging nvram

Use the show logging nvram command to display the messages in the NVRAM log.

show logging nvram [last number-lines]

Syntax Description

last number-lines

(Optional) Enters the number of lines to display. The specified number of lines is displayed. Specify from 1 to 100 lines.


Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to display the last 20 messages in the NVRAM log:

switch# show logging nvram last 20  

show logging onboard

To display the onboard logging information based on the error type, use the show logging onboard command.

show logging onboard {boot-uptime | device-version | endtime | environmental-history | exception-log | kernel-trace | obfl-history | obfl-logs | stack-trace | starttime | status} [> file | | type]

Syntax Description

boot-uptime

Displays the OBFL boot and uptime information.

device-version

Displays the OBFL device version information.

endtime

Displays the OBFL logs until the specified end time.in the following format: mm/dd/yy-HH:MM:SS

environmental-history

Displays the OBFL environmental history.

exception-log

Displays the OBFL exception log.

kernel-trace

Displays the OBFL kernel trace information.

obfl-history

Displays the OBFL history information.

obfl-logs

Displays the OBFL technical support log information.

stack-trace

Displays the OBFL kernel stack trace information.

starttime

Displays the OBFL logs from the specified start time in the following format: mm/dd/yy-HH:MM:SS

status

Displays the OBFL status enable or disable.

> file

(Optional) Redirects the output to a file. See the "Usage Guidelines" section for additional information.

| type

(Optional) Filters the output. See the "Usage Guidelines" section for additional information.


Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Usage Guidelines

The date and time arguments for the starttime and endtime keywords are entered as the date month/day/year (mm/dd/yy), followed by a hyphen, and the time in 24-hour format in hours:minutes:seconds (HH:MM:SS). For example:

starttime 03/17/08-15:01:57

endtime 03/18/08-15:04:57

The valid values for file are as follows:

bootflash:

ftp:

scp:

sftp:

tftp:

volatile:

The valid values for type are as follows:

begin [-i] [-x] [word]—Begin with the line that matches the text.

-i—Ignores the case difference when comparing the strings.

-x—Prints only the lines where the match is a whole line.

word—Specifies for the expression.

count [> file | | type]—Counts number of lines.

egrep | grep print-match—Egrep or Grep. Egrep searches for lines of text that match more sophisticated regular expression syntax than grep. Grep searches for lines of text that match one or many regular expressions, and outputs only the matching lines.

-A num—Prints the specifies number of lines of context after every matching line. Range: 1 to 999.

-B num—Prints the specifies number of lines of context before every matching line. Range: 1 to 999.

-c—Prints a total count of matching lines only.

-i—Ignores the case difference when comparing the strings.

-n—Prints each match preceded by its line number.

-v—Prints only the lines that contain no matches for the word argument.

-w—Prints only lines where the match is a complete word

-x—Prints only the lines where the match is a whole line.

word—Specifies for the expression.

exclude [-i] [-x] [word]—Excludes the lines that match.

-i—Ignores the case difference when comparing the strings.

-x—Prints only the lines where the match is a whole line.

word—Specifies for the expression.

head [-n num]—Stream Editor. The optional -n num keyword and argument allows you to specify the number of lines to print. Range: 0 to 2147483647.

include [-i] [-x] [word]—Include the lines that match

-i—Ignores the case difference when comparing the strings.

-x—Prints only the lines where the match is a whole line.

word—Specifies for the expression.

last [num]—Displays the last lines to print. The optional num specifies the number of lines to print. Range: 0 to 9999.

less [-E | -d]—Quits at the end of the file.

-E—(Optional) Quits at the end of the file.

-d—(Optional) Specifies a dumb terminal.

no-more—Turns-off pagination for command output.

sed command—Stream Editor

wc—Counts words, lines, and characters.

-c—(Optional) Specifies the output character count.

-l—(Optional) Specifies the output line count.

-w—(Optional) Specifies the output word count.

>—Redirects it to a file.

|—Pipes command output to filter.

Use this command to view OBFL data from system hardware. The OBFL feature is enabled by default and records operating temperatures, hardware uptime, interrupts, and other important events and messages that can assist with diagnosing problems with hardware cards or modules installed in a Cisco router or switch. Data is logged to files stored in nonvolatile memory. When the onboard hardware is started up, a first record is made for each area monitored and becomes a base value for subsequent records.

The OBFL feature provides a circular updating scheme for collecting continuous records and archiving older (historical) records, ensuring accurate data about the system. Data is recorded in one of two formats: continuous information that displays a snapshot of measurements and samples in a continuous file, and summary information that provides details about the data being collected. The message "No historical data to display" is seen when historical data is not available.

Examples

This example shows how to display the OBFL boot and uptime information:

switch# show logging onboard boot-uptime  
Sun Nov  9 06:11:59 2008:  Boot Record 
------------------------------------------------------------------------------- 
Boot Time..........:  Sun Nov  9 06:11:58 2008 
Slot Number........:  1 
Serial Number......:  FLC12280050 
Bios Version.......:    v1.2.0(06/19/08) 
Firmware Version...:  4.0(1a)N1(1) [build 4.0(1a)N1(1)] 
 

Table 7-1 describes the significant fields shown in the display.

Table 7-1 show logging onboard boot-uptime Command Output

Field
Description

Boot Time

Time boot occurred.

Slot Number

Slot number

Serial Number

Serial number of the module.

Bios Version

Primary binary input and output system (BIOS) version.

Firmware Version

Firmware version.


This example shows how to display the OBFL logging device information:

switch# show logging onboard device-version  
---------------------------- 
OBFL Data for 
    Module:  1 
---------------------------- 
 
Device Version Record 
---------------------------------------------------------------------- 
Timestamp                  Device Name      Instance Hardware Software 
                                                 Num  Version  Version 
---------------------------------------------------------------------- 
Sun Nov  3 07:07:00 2008   GATOS                   2        2        0 
Sun Nov  3 07:07:00 2008   GATOS                   3        2        0 
Sun Nov  3 07:07:00 2008   GATOS                   4        2        0 
Sun Nov  3 07:07:00 2008   GATOS                   5        2        0 
Sun Nov  3 07:07:00 2008   GATOS                   6        2        0 
Sun Nov  3 07:07:00 2008   GATOS                   7        2        0 
Sun Nov  3 07:07:00 2008   GATOS                   8        2        0 
Sun Nov  3 07:07:00 2008   GATOS                   9        2        0 
Sun Nov  3 07:07:00 2008   GATOS                  10        2        0 
Sun Nov  3 07:07:00 2008   GATOS                  11        2        0 
Sun Nov  3 07:07:00 2008   GATOS                  12        2        0 
Sun Nov  3 07:07:00 2008   GATOS                  13        2        0 
Mon Nov  4 00:15:08 2008   ALTOS                   0        2        0 
Mon Nov  4 00:15:08 2008   GATOS                   0        2        0 
Mon Nov  4 00:15:08 2008   GATOS                   1        2        0 
Mon Nov  4 00:15:08 2008   GATOS                   2        2        0 
 

Table 7-2 describes the significant fields shown in the display.

Table 7-2 show logging onboard device-version Command Output

Field
Description

Timestamp

Day, date, and time.

Device Name

Device name.

Instance Num

Number of instances.

Hardware Version

Hardware device version.

Software Version

Software device version.


This example shows how to display the OBFL history information:

switch# show logging onboard obfl-history  

The show logging onboard obfl-history command displays the following information:

Timestamp when OBFL is manually disabled.

Timestamp when OBFL is manually enabled.

Timestamp when OBFL data is manually cleared.

This example shows how to display the OBFL kernel stack trace information:

switch# show logging onboard stack-trace  

The show logging onboard stack-trace command displays the following information:

Time in seconds

Time in microseconds

Error description string

Current process name and identification

Kernel jiffies

Stack trace

Related Commands

clear logging onboard

Clears the OBFL entries in the persistent log.

hw-module logging onboard

Enables or disabled OBFL entries based on the error type.


show logging server

Use the show logging server command to display the syslog server configuration.

show logging server

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to display the syslog server configuration:

switch# show logging server  

Related Commands

Command
Description

logging server

Configures a remote syslog server.


show logging session status

Use the show logging session status command to display the logging session status.

show logging session status

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to display the logging session status:

switch# show logging session status  

show logging status

Use the show logging status command to display the logging status.

show logging status

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to display the logging status:

switch# show logging status  

show logging timestamp

Use the show logging timestamp command to display the logging timestamp configuration.

show logging timestamp

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to display the logging timestamp configuration:

switch# show logging timestamp  

Related Commands

Command
Description

logging timestamp

Configures the logging timestamp granularity.


show ntp peer-status

To do display the status of the Network Time Protocol peers, use the show ntp peer-status command.

show ntp peer-status

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the peer status for NTP:

switch(config)# show ntp peer-status  

Related Commands

Command
Description

show ntp peers

Displays information about NTP peers.


show ntp peers

To display information about Network Time Protocol (NTP) peers, use the show ntp peers command.

show ntp peers

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example displays information about NTP peers:

switch(config)# show ntp peers  

Related Commands

Command
Description

show ntp peer-status

Displays status information about NTP peers.


show ntp statistics

To display Network Time Protocol (NTP) statistics, use the show ntp statistics command.

show ntp statistics {io | local | memory | peer {ipaddr address | name name1 [..nameN]}

Syntax Description

io

Show the input-output statistics.

local

Show the counters maintained by the local NTP.

memory

Show the statistics counters related to memory code.

peer

Show the per-peer statistics counter of a peer.

ipaddr address

Displays statistics for the peer with the configured IPv4 or IPv6 address. The IPv4 address format is dotted decimal, x.x.x.x. The IPv6 address format is hexadecimal A:B::C:D.

name name1 [..nameN]

Displays statistics for one or more named peers.


Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example displays statistics for NTP:

switch(config)# show ntp statistics local  

Related Commands

Command
Description

clear ntp statistics

Clears NTP statistics


show ntp timestamp-status

To display the Network Time Protocol timestamp information, use the show ntp timestamp-status command.

show ntp timestamp-status

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example displays the NTP timestamp status:

switch(config)# show ntp timestamp-status  

System Message Logging Facilities

Table 7-3 lists the facilities that you can use in system message logging configuration.

Table 7-3 System Message Logging Facilities 

Facility
Description

aaa

Sets level for aaa syslog messages.

aclmgr

Sets level for aclmgr syslog messages.

adjmgr

Sets syslog filter level for Adjacency Manager.

afm

Sets level for afm syslog messages.

all

Sets level for all facilities.

altos

Altos syslog level.

arp

Sets syslog filter level for ARP.

auth

Sets level for Authorization System.

authpriv

Sets level for Authorization (Private) system.

bootvar

Sets level for bootvar.

callhome

Callhome syslog level.

capability

Sets syslog level for mig utils daemon.

cdp

Sets logging level for CDP.

cert-enroll

Cert-enroll syslog level.

cfs

Sets logging level for CFS.

clis

Sets syslog filter level for CLIS.

core

core daemon syslog level.

cron

Sets level for Cron/at facility.

daemon

Sets level for System daemons.

dcbx

Sets level for dcx syslog messages.

device-alias

Sets syslog level for Device Alias Distribution Service.

dstats

delta statistics syslog level.

epp

Sets level for EPP syslog messages.

ethpc

Sets level for ethpc syslog messages.

ethpm

Sets level for ethpm syslog messages.

evmc

Sets level for evmc syslog messages.

fabric_start_cfg_mgr

fabric start cfg mgr syslog level.

fc2d

Sets level for fc2d syslog messages.

fcdomain

set level for fcdomain syslog messages.

fcns

Sets syslog filter level for name server.

fcpc

Sets level for fcpc syslog messages.

fcs

Sets syslog filter level for FCS.

fdmi

Sets logging level for fdmi.

feature-mgr

Feature manager syslog level.

flogi

Configure level for flogi syslog messages.

fs-daemon

fs daemon syslog level.

fspf

FSPF syslog level.

ftp

Sets level for File Transfer System.

fwm

Sets level for fwm syslog messages.

gatos

Gatos syslog level.

im

Sets level for im syslog messages.

kernel

Sets level for kernel.

l3vm

Sets syslog filter level for L3VM.

license

Licensing syslog level.

local0

Sets level for Local use daemons.

local1

Sets level for Local use daemons.

local2

Sets level for Local use daemons.

local3

Sets level for Local use daemons.

local4

Sets level for Local use daemons.

local5

Sets level for Local use daemons.

local6

Sets level for Local use daemons.

local7

Sets level for Local use daemons.

lpr

Sets level for Line Printer System.

mail

Sets level for Mail system.

monitor

Sets level for ethernet span syslog messages.

news

Sets level for USENET news.

nohms

Sets level for nohms syslog messages.

nqosm

Sets level for nqosm syslog messages.

ntp

Sets syslog filter level for NTP.

pfm

Sets level for pfm syslog messages.

pktmgr

Sets syslog filter level for Packet Manager.

plugin

Sets level for plugin syslog messages.

port

Sets level for port syslog messages.

port-channel

Sets level for EtherChannel syslog messages.

qd

Sets level for qd syslog messages.

radius

RADIUS syslog level.

rdl

Sets logging level for RDL.

res_mgr

Set slevel for res_mgr syslog messages.

rib

Sets level for rib.

rlir

Sets level for RLIR.

rscn

sets level for RSCN.

san-port-channel

Sets level for san-port-channel syslog messages.

scsi-target

scsi target daemon syslog level.

security

Security syslog level.

session

Sets level for session-manager syslog messages.

sifmgr

Sets level for sifmgr syslog messages.

spanning-tree

Sets level for stp syslog messages.

stp

Sets level for stp syslog messages.

syslog

Sets level for Internal Syslog Messages.

sysmgr

System Manager syslog level.

tcpudp

Sets syslog filter level for TCPUDP.

track

Sets level for track syslog messages.

urib

Sets syslog filter level for URIB.

user

Sets level for User Process.

uucp

Sets level for Unix-to-Unix copy system.

vlan_mgr

Sets level for VLAN syslog messages.

vmm

Sets level for vmm syslog messages.

vsan

VSAN syslog level.

vshd

Sets logging level for vshd.

wwnm

Sets WWN Manager syslog level.

xml

XML agent syslog level.

zone

Sets syslog filter level for zone server.

zschk

Sets level for zschk syslog messages.