Cisco Nexus 5000 Series Command Reference
Quality of Service Commands
Downloads: This chapterpdf (PDF - 220.0KB) The complete bookPDF (PDF - 3.14MB) | Feedback

Quality of Service Commands

Table Of Contents

Quality of Service Commands

class-map

flowcontrol

match cos (class map type qos)

match access-group

match class-map

match cos (class map type qos)

match cos (class map type queuing)

match dscp

match ip rtp

match precedence

match protocol

policy-map type qos

priority-flow-control

service-policy

show class-map type qos

show class-map type queuing

show interface priority-flow-control

show policy-map

show policy-map interface

show policy-map interface brief

show policy-map interface

show queuing interface

system jumbomtu

system qos

untagged cos


Quality of Service Commands


This chapter describes the Cisco NX-OS quality of service commands available on Cisco Nexus 5000 Series switches.

class-map

To create or modify a class map and enter the class-map configuration mode, use the class-map command. To remove a class map, use the no form of this command.

class-map class-map-name

no class-map class-map-name

Syntax Description

class-map-name

Name assigned to the class map. The name class default is reserved.


Command Default

None

Command Modes

Global configuration.

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Usage Guidelines

You can define a class map for each class of traffic to be used in QoS policies.

Examples

This example shows how to create or modify a class map:

switch(config)# class-map my_class1 
switch(config-cmap)# 

This example shows how to remove a class map:

switch(config)# no class-map my_class1 

Related Commands

Command
Description

policy-map

Creates or modifies a policy map.

show class-map

Displays class maps.


flowcontrol

To enable IEEE 802.3x link-level flow control for the selected interface, use the flow-control command.

flowcontrol [receive {on | off}] [transmit {on | off}]

Syntax Description

receive {on | off}

(Optional) Sets flow control in the receive direction.

transmit {on | off}

(Optional) Sets flow control in the transmit direction.


Command Default

None

Command Modes

Interface configuration mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to enable flow control for traffic received on an interface:

switch# configure terminal 
switch(config)# interface ethernet 1/2 
switch(config-if)# flowcontrol receive on 

Related Commands

Command
Description

priority-flow-control

Sets the PFC mode for the selected interface.


match cos (class map type qos)

To define the class of traffic using the Class of Service (CoS) value in a type qos class map, use the match cos command. To remove the match on the CoS value, use the no form of this command.

match [not] cos cos-list

no match [not] cos cos-list

Syntax Description

not

(Optional) Negates the specified match result.

cos-list

Matches on the specified COS value or list of specified CoS values. Valid values are from 0 to 7.


Defaults

None

Command Modes

Class-map type qos configuration

Command History

Release
Modification

4.1(3)N1(1)

This command was introduced.


Usage Guidelines

To specify a list of values, use one of the following options:

Specify a range of values separated by a dash

Specify a noncontiguous list of values separated by commas


Note Only class maps of type qos support the optional not keyword form of this command. Class maps of type queuing do not support the not keyword.


This command does not require a license.

Examples

This example shows how to match on the CoS value for a type qos class map:

switch(config)# class-map class_acl
switch(config-cmap-qos)# match cos 5-7

Related Commands

Command
Description

show class-map

Displays class maps.


match access-group

To identify a specified access control list (ACL) group as a match criteria for a class map, use the match access-group command in the class map configuration mode. To remove ACL match criteria from a class map, use the no form of this command.

match access-group name acl-name

no match access-group name acl-name

Syntax Description

access-group name acl-name

Matches on the characteristics in the ACL name specified.


Defaults

None

Command Modes

Class-map type qos configuration

Command History

Release
Modification

4.1(3)N1(1)

This command was introduced.


Usage Guidelines


Note The permit and deny ACL keywords do not affect the matching of packets.


This command does not require a license.

Examples

This example shows how to create a qos class map that matches characteristics of the ACL my_acl:

switch(config)# class-map class_acl
switch(config-cmap-qos)# match access-group name my_acl

Related Commands

Command
Description

show class-map

Displays class maps.


match class-map

To match on the match commands in a specified class map, use the match class-map command in the class map configuration mode. To remove the match on the specified class map, use the no form of this command.

match [not] class-map class-map-name

no match [not] class-map class-map-name

Syntax Description

not

(Optional) Negates the specified match result.

class-map-name

Matches on the match commands in the specified class-map name.


Defaults

None

Command Modes

Class-map type qos configuration

Command History

Release
Modification

4.1(3)N1(1)

This command was introduced.


Usage Guidelines

This command does not require a license.

Examples

This example shows how to match on the matches specified in class map named my_test:

switch(config)# class-map my_test
switch(config-cmap-qos)# match class-name my_test

Related Commands

Command
Description

show class-map

Displays class maps.


match cos (class map type qos)

To define the class of traffic using the Class of Service (CoS) value in a type qos class map, use the match cos command. To remove the match on the CoS value, use the no form of this command.

match [not] cos cos-list

no match [not] cos cos-list

Syntax Description

not

(Optional) Negates the specified match result.

cos-list

Matches on the specified COS value or list of specified CoS values. Valid values are from 0 to 7.


Defaults

None

Command Modes

Class-map type qos configuration

Command History

Release
Modification

4.1(3)N1(1)

This command was introduced.


Usage Guidelines

To specify a list of values, use one of the following options:

Specify a range of values separated by a dash

Specify a noncontiguous list of values separated by commas


Note Only class maps of type qos support the optional not keyword form of this command. Class maps of type queuing do not support the not keyword.


This command does not require a license.

Examples

This example shows how to match on the CoS value for a type qos class map:

switch(config)# class-map class_acl
switch(config-cmap-qos)# match cos 5-7

Related Commands

Command
Description

show class-map

Displays class maps.


match cos (class map type queuing)

To define the class of traffic in a type queuing class map, use the match cos command. To remove the match configuration, use the no form of these commands.

match cos cos-list

no match cos cos-list

Syntax Description

cos-list

Matches on the specified COS value or list of specified CoS values. Valid values are from 0 to 7.


Defaults

None

Command Modes

Class-map type queuing configuration

Command History

Release
Modification

4.1(3)N1(1)

This command was introduced.


Usage Guidelines

To specify a list of values, use one of the following options:

Specify a range of values separated by a dash

Specify a noncontiguous list of values separated by commas


Note Only class maps of type qos support the optional not keyword form of this command.


This command does not require a license.

Examples

This example shows how to modify a type queuing class map to match on CoS:

switch(config)# class-map type queuing match-any 8q2t-in-q4
switch(config-cmap-que)# match cos 3
switch(config-cmap-que)# 

Related Commands

Command
Description

show class-map

Displays class maps.


match dscp

To identify specific Differentiated Services code point (DSCP) values as a match criteria, use the match dscp command. To remove specified DSCP values as a match criteria, use the no form of this command.

match [not] dscp dscp-list

no match [not] dscp dscp-list

Syntax Description

not

(Optional) Negates the specified match result.

dscp-list

Matches on the specified DSCP value or list of DSCP values. See Table 1 for a list of valid DSCP values.


Defaults

None

Command Modes

Class-map type qos configuration

Command History

Release
Modification

4.1(3)N1(1)

This command was introduced.


Usage Guidelines

The standard DSCP values are shown in Table 1.

Table 1 Standard DSCP Values 

 
List of DSCP Values

af11

AF11 dscp (001010)—decimal value 10

af12

AF12 dscp (001100)—decimal value 12

af13

AF13 dscp (001110)—decimal value 14

af21

AF21 dscp (010010)—decimal value 18

af22

AF22 dscp (010100)—decimal value 20

af23

AF23 dscp (010110)—decimal value 22

af31

AF31 dscp (011010)—decimal value 26

af32

AF40 dscp (011100)—decimal value 28

af33

AF33 dscp (011110)—decimal value 30

af41

AF41 dscp (100010)—decimal value 34

af42

AF42 dscp (100100)—decimal value 36

af43

AF43 dscp (100110)—decimal value 38

cs1

CS1 (precedence 1) dscp (001000)—decimal value 8

cs2

CS2 (precedence 2) dscp (010000)—decimal value 16

cs3

CS3 (precedence 3) dscp (011000)—decimal value 24

cs4

CS4 (precedence 4) dscp (100000)—decimal value 32

cs5

CS5 (precedence 5) dscp (101000)—decimal value 40

cs6

CS6 (precedence 6) dscp (110000)—decimal value 48

cs7

CS7 (precedence 7) dscp (111000)—decimal value 56

default

Default dscp (000000)—decimal value 0

ef

EF dscp (101110)—decimal value 46


To specify a list of values, use one of the following options:

Specify a range of values separated by a dash

Specify a noncontiguous list of values separated by commas

This command does not require a license.

Examples

This example shows how to match on DSCP value af21:

switch(config)# class-map my_test
switch(config-cmap-qos)# match dscp af21

Related Commands

Command
Description

show class-map

Displays class maps.


match ip rtp

To configure a class map to use the Real-Time Protocol (RTP) port as a match criteria, use the match ip rtp command. To remove the RTP port as a match criteria, use the no form of this command.

match [not] ip rtp port-list

no match [not] ip rtp port-list

Syntax Description

not

(Optional) Negates the specified match result.

port-list

Matches on the specified UDP or list of UDP ports that are using RTP. Valid values range from 2000 to 65535.


Defaults

None

Command Modes

Class-map type qos configuration

Command History

Release
Modification

4.1(3)N1(1)

This command was introduced.


Usage Guidelines

To specify a list of values, use one of the following options:

Specify a range of values separated by a dash

Specify a noncontiguous list of values separated by commas

This command does not require a license.

Examples

This example shows how to match on a port using RTP:

switch(config)# class-map my_test
switch(config-cmap-qos)# match ip rtp 2300

Related Commands

Command
Description

show class-map

Displays class maps.


match precedence

To configure a class map to use the precedence value in the Type of Service (TOS) byte field of the IP header as a match criteria, use the match precedence command. To remove the precedence values as a match criteria, use the no form of this command.

match [not] precedence precedence-list

no match [not] precedence precedence-list

Syntax Description

not

(Optional) Negates the specified match result.

precedence-list

Matches on the specified IP precedence value or list of IP precedence values specified in bytes. Valid values are shown in Table 2.


Defaults

None

Command Modes

Class-map type qos configuration

Command History

Release
Modification

4.1(3)N1(1)

This command was introduced.


Usage Guidelines

See Table 2 for a list of precedence values.

Table 2 Precedence Values 

 
List of Precedence Values

<0-7>

IP precedence value

critical

Critical precedence (5)

flash

Flash precedence (3)

flash-override

Flash override precedence (4)

immediate

Immediate precedence (2)

internet

Internetwork control precedence (6)

network

Network control precedence (7)

priority

Priority precedence (1)

routine

Routine precedence (0)


To specify a list of values, use one of the following options:

Specify a range of values separated by a dash

Specify a noncontiguous list of values separated by commas

This command does not require a license.

Examples

This example shows how to match on an IP precedence value:

switch(config)# class-map my_test
switch(config-cmap-qos)# match precedence 7

Related Commands

Command
Description

show class-map

Displays class maps.


match protocol

To configure a class map to use a specific protocol as a match criterion, use the match protocol command. To remove the specified protocol as a match criteria, use the no form of this command.

match [not] protocol protocol-name

no match [not] protocol protocol-name

Syntax Description

not

(Optional) Negates the specified match result.

protocol-name

Matches on the specified protocol name. Valid values are shown in Table 3.


Defaults

None

Command Modes

Class-map type qos configuration

Command History

Release
Modification

4.1(3)N1(1)

This command was introduced.


Usage Guidelines

The list of valid protocol names is shown in Table 3.

Table 3 Protocol Names

Argument
Description

arp

Address Resolution Protocol (ARP)

bridging

Bridging

cdp

Cisco Discovery Protocol (CDP)

clns

Connectionless Network Service (CLNS)

clns_es

CLNS End Systems

clns_is

CLNS Intermediate System

dhcp

Dynamic Host Configuration (DHCP)

isis

Intermediate system to intermediate system (IS-IS)

ldp

Label Distribution Protocol (LDP)

netbios

NetBIOS Extended User Interface (NetBEUI)



Note A maximum of eight different of the above protocols can be matched at one time.


To specify more than one protocol, enter the command more than once with the desired protocol value each time.

This command does not require a license.

Examples

This example shows how to match on a specified protocol:

switch(config)# class-map my_test
switch(config-cmap-qos)# match protocol ldp

Related Commands

Command
Description

show class-map

Displays class maps.


policy-map type qos

To create or modify a policy map and enter the policy map type qos configuration mode, use the policy-map type qos command. To remove a policy map, use the no form of this command.

policy-map [type qos] [match-first] qos-policy-map-name

no policy-map [type qos] [match-first] qos-policy-map-name

Syntax Description

match-first

(Optional) Specifies that policies associated with the first class that matches the packet characteristics are executed. This is the default action if this option is not specified.

Note Because this is the default action, you do not need to enter this variable; it is here to ensure compatibility with other systems.

qos-policy-map-name

Name assigned to a type qos policy map.


Defaults

The software enters the policy map type qos configuration mode if you enter the policy-map command without specifying a type.

Command Modes

Global configuration

Command History

Release
Modification

4.1(3)N1(1)

This command was introduced.


Usage Guidelines

Use the service-policy command to assign policy maps to interfaces.

This command does not require a license.

Examples

This example shows how to create or modify a type qos policy map:

switch(config)# policy-map my_policy1
switch(config-pmap-qos)#

This example shows how to remove a type qos policy map:

switch(config)# no policy-map my_policy1

Related Commands

Command
Description

service-policy

Attaches a policy map to an interface.

show policy-map

Displays policy maps.


priority-flow-control

To set the (priority-flow-control) PFC mode for the selected interface, use the priority-flow-control command.

priority-flow-control mode {auto | on}

Syntax Description

auto

Negotiates PFC capability.

on

Force-enables PFC.


Command Default

None

Command Modes

Interface configuration mode

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to force-enable PFC on an interface:

switch# configure terminal 
switch(config)# interface ethernet 1/2 
switch(config-if)# priority-flow-control mode on 

Related Commands

Command
Description

flowcontrol

Sets link-level flow control for the selected interface.


service-policy

To attach a policy map to an interface, VLAN, or tunnel, use the service-policy command. To remove a service-policy from an interface, VLAN or tunnel, use the no form of this command.

service-policy [type {qos | queuing|network-qos}] {input | output} policy-map-name

no service-policy [type {qos | queuingg|network-qos}] {input | output} policy-map-name

Syntax Description

type

(Optional) Specifies whether the policy map is of type qos or queuing.

qos

Specifies a policy map of type qos.

queuing

Specifies a policy map of type queuing.

input

Applies this policy map to packets coming into this interface.

output

Applies this policy map to packets going out of this interface.

policy-map-name

Name of the policy map to attach to this interface. Only one policy map can be attached to the input and one to the output of a given interface for each of the policy type qos and queuing.


Defaults

type default is qos.

No policies of type qos are active on an interface until the service-policy command is issued. The system-defined type queuing class maps are attached to each interface unless you specifically attach a different class map.

Command Modes

Interface configuration
VLAN configuration

Command History

Release
Modification

4.1(3)N1(1)

This command was introduced.


Usage Guidelines

No policies of type qos are active on an interface until you enter the service-policy command. The system-defined type queuing class maps are attached to each interface unless you specifically attach a different class map.

You can attach one ingress and one egress type qos policy map to port, port channel, tunnel, and VLANs. You can attach one ingress and one egress type queuing policy map to an interface of type port, port channel, tunnel, and VLAN.

Only one policy map can be attached to the input and one to the output of a given interface for each of the policy type qos and queuing.


Note For more information on using service policies, see the Cisco Nexus 5000 Series Configuration Guide, Cisco NX-OS Release 4.1.


This command does not require a license.

Examples

This example shows how to attach qos type policy maps to the ingress and egress packets of a VLAN:

switch(config)# vlan 1
switch(config-vlan)# service-policy input my_input_policy
switch(config-vlan)# service-policy output my_output_policy
switch(config-vlan)# 

This example shows how to attach a queuing policy map to the ingress packets of a port interface:

switch(config)# interface ethernet 2/1
switch(config-if)# service-policy type queuing input my_input_q_policy
switch(config-if)# 

This example shows how to remove a policy map from a VLAN:

switch(config)# vlan 1
switch(config-vlan)# no service-policy input my_input_policy
switch(config-vlan)# 

Related Commands

Command
Description

show policy-map interface brief

Displays all interfaces and VLANs with attached service policies in a brief format.


show class-map type qos

To display type qos class maps, use the show class-map type qos command.

show class-map type qos [class-map-name | color-class-map-name]

Syntax Description

class-map-name

Named class map. The name class-default is reserved.

color-class-map-name

System-defined color class map.


Defaults

Displays all type qos class maps if no class map name is specified.

Command Modes

Any command mode

Command History

Release
Modification

4.1(3)N1(1)

This command was introduced.


Usage Guidelines

This command does not require a license.

Examples

This example shows how to display all type qos class maps:

switch(config)# show class-map type qos

Related Commands

Command
Description

class-map

Creates or modifies a class map.



show class-map type queuing

To display type queuing class maps, use the show class-map type queuing command.

show class-map type queuing [class-map-name]

Syntax Description

class-map-name

Named class map.


Defaults

Displays all type queuing class maps if no class map name is specified.

Command Modes

Any command mode

Command History

Release
Modification

4.1(3)N1(1)

This command was introduced.


Usage Guidelines

This command does not require a license.

Examples

This example shows how to display all type queuing class maps:

switch(config)# show class-map type queuing

Related Commands

Command
Description

class-map

Creates or modifies a class map.


show interface priority-flow-control

To display the priority flow control details for a specified interface, use the show interface priority-flow-control command.

show interface [name] priority-flow-control

Syntax Description

name

(Optional) Name of the interface.


Command Default

None

Command Modes

Global configuration.

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to display the priority flow control details for a specified interface:

switch(config)# show interface ethernet 1/1 priority-flow-control  
--------------------------------------- 
Port       Mode Oper RxPPP      TxPPP 
--------------------------------------- 
Eth1/1     auto off  0          0 

The interface specified is Ethernet 1/1, the PFC mode is set to negotiate PFC capability, the operation is off and packets transmitted is zero.

Related Commands

Command
Description

priority-flow-control

Sets the PFC mode for the selected interface.


show policy-map

To display policy maps, use the show policy-map command.

show policy-map [type {qos | queuing|network-qos}] [policy-map-name]

Syntax Description

type

(Optional) Specifies the component type to display.

qos

Displays policy maps of type qos only.

queuing

Displays policy maps of type queuing only.

policy-map-name

(Optional) Displays a named policy map.


Defaults

None.

Command Modes

Any command mode

Command History

Release
Modification

4.1(3)N1(1)

This command was introduced.


Usage Guidelines

When you enter the command show policy-map with no arguments or keywords, the system also displays the Control Plane Policing (CoPP) information.

This command does not require a license.

Examples

This example shows how to display a named policy map:

switch(config)# show policy-map abc
switch(config)# show policy-map type queuing

Related Commands

Command
Description

class-map

Creates or modifies a class map.



show policy-map interface

To display the service policy maps configured on the the interfaces, use the show policy-map interface command.

show policy-map interface [ethernet {slot/port} | port-channel {channel-number}] [input | output] [type {qos | queuing}]

Syntax Description

ethernet

(Optional) Displays policy maps assigned to Ethernet interfaces.

slot/port

Displays policy maps assigned to specified interface.

port-channel

(Optional) Displays policy maps assigned to port channels.

channel-number

Displays policy maps assigned to specified port channel.

input

(Optional) Displays policy maps assigned to input traffic only.

output

(Optional) Displays policy maps assigned to output traffic only.

type

(Optional) Specifies the component type to display.

qos

Displays policy maps of type qos only.

queuing

Displays policy maps of type queuing only.


Defaults

None.

Command Modes

Any command mode

Command History

Release
Modification

4.1(3)N1(1)

This command was introduced.


Usage Guidelines

Statistics are on by default.

This command does not require a license.

Examples

This example shows how to display the service policies assigned to interfaces:

switch# show policy-map interface 

Global statistics status :   disabled

Ethernet1/1

  Service-policy (qos) input:   default-in-policy
    policy statistics status:   disabled

    Class-map (qos):   class-default (match-any)
      Match: any
      set qos-group 0

  Service-policy (queuing) input:   default-in-policy
    policy statistics status:   disabled

    Class-map (queuing):   class-default (match-any)
      Match: qos-group 0
      bandwidth percent 100

  Service-policy (queuing) output:   default-out-policy
    policy statistics status:   disabled

--More--
<--output truncated-->
switch#

This example shows how to display policy maps assigned to a specified interface:

switch(config)# show policy-map interface ethernet 2/10
switch(config)# show policy-map interface ethernet 2/2 type qos

Related Commands

Command
Description

class-map

Creates or modifies a class map.



show policy-map interface brief

To display policy maps applied to interfaces in a brief format, use the show policy-map interface brief command.

show policy-map interface brief

Syntax Description

This command has no arguments or keywords.

Defaults

None

Command Modes

Any command mode

Command History

Release
Modification

4.1(3)N1(1)

This command was introduced.


Usage Guidelines

This command does not require a license.

Examples

This example shows how to display assigned policy maps in a brief format:

switch(config)# show policy-map interface brief

 Interface/VLAN [Status]:INP QOS       OUT QOS       INP QUE       OUT QUE
================================================================================
port-channel5   [Active]:                            default-in-po default-out-p

port-channel20  [Active]:                            default-in-po default-out-p

port-channel30  [Active]:                            default-in-po default-out-p

port-channel37  [Active]:                            default-in-po default-out-p

port-channel50  [Active]:                            default-in-po default-out-p


Ethernet2/2     [Active]:                            default-in-po default-out-p

Ethernet2/3     [Active]:                            default-in-po default-out-p

==================================================================================

Related Commands

Command
Description

show policy-map

Displays policy maps.


show policy-map interface

To display the system policy configured on the system and per class statistics, use the show policy-map interface command.

show policy-map interface [name]

Syntax Description

name

(Optional) Name of the interface.


Command Default

None

Command Modes

Global configuration.

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Usage Guidelines

This command provides per class statistics.

Examples

This example shows the per class pause statistics displayed for a default system class:

switch(config)# show policy-map interface ethernet 3/1 

Related Commands

Command
Description

policy-map

Creates or modifies a policy map.

show policy-map

Displays policy maps.


show queuing interface

To display the queuing information of interfaces, use the show queuing interface command.

show queuing interface [ethernet slot-chassis-no/port-slot-no/port-no]

Syntax Description

ethernet

(Optional) Specifies that queuing information be displayed for an Ethernet interface or a Fabric Extender.

slot-chassis-no

Slot number of the Ethernet interface or chassis ID of the Fabric Extender. The range is from 1 to 255.

port-slot-no

Port number of the Ethernet interface or the remote slot ID of the Fabric Extender. The range is from 1 to 128.

port-no

Port number of the Fabric Extender. The range is from 1 to 48.


Command Default

Displays the queuing information for all interfaces.

Command Modes

EXEC mode

Command History

Release
Modification

4.1(3)N1(1)

This command was introduced.


Examples

This example shows how to display the queuing information of a specified interface:

switch# show queuing interface ethernet 1/4 

Interface Ethernet1/4 TX Queuing
qos-group  sched-type  oper-bandwidth
    0       WRR             50
    1       WRR             50
    5       priority         0

Interface Ethernet1/4 RX Queuing
qos-group  0: 
    q-size: 102400, MTU: 1538
    drop-type: drop, xon: 0, xoff: 640
    Statistics:
        Pkts received over the port             : 1
        Ucast pkts sent to the cross-bar        : 0
        Mcast pkts sent to the cross-bar        : 1
        Ucast pkts received from the cross-bar  : 1577841
        Pkts sent to the port                   : 1577841
        Pkts discarded on ingress               : 0
        Per-priority-pause status               : Rx (Inactive), Tx (Inactive)

qos-group  1: 
    q-size: 76800, MTU: 2240
    drop-type: no-drop, xon: 128, xoff: 240
    Statistics:
        Pkts received over the port             : 0
        Ucast pkts sent to the cross-bar        : 0
        Mcast pkts sent to the cross-bar        : 0
        Ucast pkts received from the cross-bar  : 0
        Pkts sent to the port                   : 0
        Pkts discarded on ingress               : 0
        Per-priority-pause status               : Rx (Inactive), Tx (Inactive)

qos-group  5: 
    q-size: 122880, MTU: 1538
    drop-type: drop, xon: 0, xoff: 768
    Statistics:
        Pkts received over the port             : 0
        Ucast pkts sent to the cross-bar        : 0
        Mcast pkts sent to the cross-bar        : 0
        Ucast pkts received from the cross-bar  : 0
        Pkts sent to the port                   : 1
        Pkts discarded on ingress               : 0
        Per-priority-pause status               : Rx (Inactive), Tx (Inactive)
switch#

Table 5-4 describes the significant fields shown in the display.

Table 5-4 show queuing interface Field Descriptions 

Field
Description

Ethernet ...

Ethernet interface information.

qoS-group

Information about QoS groups configured on the switch.

sched-type

Type of schedule.

WRR

Weighted round robin(WRR). Queue eight for scheduling.

Priority

Priority of the queue.

q-size

Queue size.

drop-type

Queue drop type can be either drop or no-drop.

MTU

Maximum transmit unit (MTU) for the queue.

Xon

Transmission on at this threshold.

Xoff

Transmission off at this threshold.


Related Commands

Command
Description

show fex

Displays all configured Fabric Extender chassis connected to the switch.


system jumbomtu

To define the upper bound of any MTU in the system, use the system jumbomtu command.

system jumbomtu [value]

Syntax Description

value

The jumbomtu value. The range is 2240-9216.


Command Default

9216 bytes

Command Modes

Global configuration

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to define the upper bound of any MTU in the system:

switch(config)# system jumbomtu 9216  

Related Commands

Command
Description

show interface

Displays the jumbo MTU frames sent and received on the specified interface.


system qos

To configure system policy, use the system qos command.

system qos

Syntax Description

None

Command Default

None

Command Modes

Global configuration

Command History

Release
Modification

4.0(0)N1(1a)

This command was introduced.


Examples

This example shows how to configure a system qos:

switch# configure terminal 
switch(config)# system qos 

Related Commands

Command
Description

service- policy

Associates the system class policy-map to the service policy for the system


untagged cos

Ethernet frames received with no CoS value are given a CoS value of 0. To override this value for the selected interface, use the untagged cos command.

untagged cos cos-value

Syntax Description

cos-value

Specifies a Class of Service (CoS) value for untagged frames. Values can range from 1 to 7.


Command Default

None

Command Modes

Interface configuration mode

Command History

Release
Modification

4.0(1a)N1(1)

This command was introduced.


Usage Guidelines

No license required for the command.

Examples

This example shows how to set the CoS value to 4 for untagged frames received on an interface:

switch# configure terminal 
switch(config)# interface ethernet 1/2 
switch(config-if)# untagged cos 4 

Related Commands

Command
Description

match cos

Sets the CoS value to match for the selected class.