Cisco Nexus 3000 Series NX-OS Multicast Configuration Guide, Release 5.0(3)U5(1)
Configuring IGMP Snooping
Downloads: This chapterpdf (PDF - 247.0KB) The complete bookPDF (PDF - 3.58MB) | Feedback

Configuring IGMP Snooping

Table Of Contents

Configuring IGMP Snooping

Information About IGMP Snooping

IGMPv1 and IGMPv2

IGMPv3

IGMP Snooping Querier

IGMP Filtering on Router Ports

IGMP Snooping with VRFs

Licensing Requirements for IGMP Snooping

Prerequisites for IGMP Snooping

Default Settings

Configuring IGMP Snooping

Configuring IGMP Snooping Global Parameters

Configuring IGMP Snooping Parameters per VLAN

Viewing IGMP Snooping Status per VLAN

Configuring IGMP Snooping Parameters

Verifying the IGMP Snooping Configuration

Displaying IGMP Snooping Statistics

Configuration Examples for IGMP Snooping

Where to Go Next

Field Descriptions for Configuring IGMP Snooping

Device: Device Details Tab

VLANs: Details Tab

VLANs: Status Tab

Additional References

Related Documents

Standards

Feature History for IGMP Snooping

Feature History for IGMP Snooping in GUI


Configuring IGMP Snooping



Note The Cisco NX-OS release that is running on a managed device may not support all the features or settings described in this chapter. For the latest feature information and caveats, see the documentation and release notes for your platform and software release.


This chapter describes how to configure Internet Group Management Protocol (IGMP) snooping on a Cisco NX-OS switch.

This chapter includes the following sections:

Information About IGMP Snooping

Licensing Requirements for IGMP Snooping

Default Settings

Configuring IGMP Snooping

Configuring IGMP Snooping Parameters

Verifying the IGMP Snooping Configuration

Displaying IGMP Snooping Statistics

Configuration Examples for IGMP Snooping

Where to Go Next

Field Descriptions for Configuring IGMP Snooping

Additional References

Feature History for IGMP Snooping

Information About IGMP Snooping


Note We recommend that you do not disable IGMP snooping on the switch. If you disable IGMP snooping, you may see reduced multicast performance because of excessive false flooding within the switch.


The Internet Group Management Protocol (IGMP) snooping software examines Layer 2 IP multicast traffic within a VLAN to discover the ports where interested receivers reside. Using the port information, IGMP snooping can reduce bandwidth consumption in a multi-access LAN environment to avoid flooding the entire VLAN. The IGMP snooping feature tracks which ports are attached to multicast-capable routers to help the routers forward IGMP membership reports. The IGMP snooping software responds to topology change notifications. By default, IGMP snooping is enabled on the switch.

Figure 5-1 shows an IGMP snooping switch that sits between the host and the IGMP router. The IGMP snooping switch snoops the IGMP membership reports and Leave messages and forwards them only when necessary to the connected IGMP routers.

Figure 5-1 IGMP Snooping Switch

The IGMP snooping software operates upon IGMPv1, IGMPv2, and IGMPv3 control plane packets where Layer 3 control plane packets are intercepted and influence the Layer 2 forwarding behavior.

For more information about IGMP, see Chapter 3 "Configuring IGMP."

The Cisco NX-OS IGMP snooping software has the following proprietary features:

Source filtering that allows forwarding of multicast packets based on destination and source IP.

Multicast forwarding based on IP address rather than MAC address.

Optimized multicast flooding (OMF) that forwards unknown traffic to routers only and performs no data driven state creation.

For more information about IGMP snooping, see RFC 4541.

This section includes the following topics:

IGMPv1 and IGMPv2

IGMPv3

IGMP Snooping Querier

IGMP Filtering on Router Ports

IGMPv1 and IGMPv2

Both IGMPv1 and IGMPv2 support membership report suppression, which means that if two hosts on the same subnet want to receive multicast data for the same group, then the host that receives a member report from the other host suppresses sending its report. Membership report suppression occurs for hosts that share a port.

If no more than one host is attached to each VLAN switch port, then you can configure the fast leave feature in IGMPv2. The fast leave feature does not send last member query messages to hosts. As soon as the software receives an IGMP leave message, the software stops forwarding multicast data to that port.

IGMPv1 does not provide an explicit IGMP leave message, so the software must rely on the membership message timeout to indicate that no hosts remain that want to receive multicast data for a particular group.


Note The software ignores the configuration of the last member query interval when you enable the fast leave feature because it does not check for remaining hosts.


IGMPv3

The IGMPv3 snooping implementation on Cisco NX-OS supports full IGMPv3 snooping, which provides constrained flooding based on the (S, G) information in the IGMPv3 reports. This source-based filtering enables the switch to constrain multicast traffic to a set of ports based on the source that sends traffic to the multicast group.

By default, the software tracks hosts on each VLAN port. The explicit tracking feature provides a fast leave mechanism. Because every IGMPv3 host sends membership reports, report suppression limits the amount of traffic that the switch sends to other multicast-capable routers. When report suppression is enabled, and no IGMPv1 or IGMPv2 hosts requested the same group, the software provides proxy reporting. The proxy feature builds the group state from membership reports from the downstream hosts and generates membership reports in response to queries from upstream queriers.

Even though the IGMPv3 membership reports provide a full accounting of group members on a LAN segment, when the last host leaves, the software sends a membership query. You can configure the parameter last member query interval. If no host responds before the timeout, the software removes the group state.

IGMP Snooping Querier

When PIM is not enabled on an interface because the multicast traffic does not need to be routed, you must configure an IGMP snooping querier to send membership queries. You define the querier in a VLAN that contains multicast sources and receivers but no other active querier.

When an IGMP snooping querier is enabled, it sends out periodic IGMP queries that trigger IGMP report messages from hosts that want to receive IP multicast traffic. IGMP snooping listens to these IGMP reports to establish appropriate forwarding.

IGMP Filtering on Router Ports

IGMP filtering allows users to configure a router port on the switch that leads the switch to a Layer 3 multicast switch. The switch stores all manually configured static router ports in its router port list.

When an IGMP packet is received, the switch forwards the traffic through the router port in the VLAN. The switch recognizes a port as a router port through the PIM hello message or the IGMP query received by the switch.

IGMP Snooping with VRFs

You can define multiple virtual routing and forwarding (VRF) instances. An IGMP process supports all VRFs.

You can use the show commands with a VRF argument to provide a context for the information displayed. The default VRF is used if no VRF argument is supplied.

For information about configuring VRFs, see the Cisco Nexus 3000 Series NX-OS Unicast Routing Configuration Guide.

Licensing Requirements for IGMP Snooping

The following table shows the licensing requirements for this feature:

Product
License Requirement

Cisco NX-OS

IGMP snooping requires no license. Any feature not included in a license package is bundled with the Cisco NX-OS system images and is provided at no extra charge to you. For a complete explanation of the Cisco NX-OS licensing scheme, see the Cisco NX-OS Licensing Guide.

Note Make sure the LAN Base Services license is installed on the switch to enable the Layer 3 interfaces.


Prerequisites for IGMP Snooping

IGMP snooping has the following prerequisites:

You are logged onto the switch.

For global commands, you are in the correct virtual routing and forwarding (VRF) mode. The default configuration mode shown in the examples in this chapter applies to the default VRF.

Default Settings

Table 5-1 lists the default settings for IGMP snooping parameters.

Table 5-1 Default IGMP Snooping Parameters 

Parameters
Default

IGMP snooping

Enabled

Explicit tracking

Enabled

Fast leave

Disabled

Last member query interval

1 second

Snooping querier

Disabled

Report suppression

Enabled

Link-local groups suppression

Enabled

IGMPv3 report suppression for the entire switch

Disabled

IGMPv3 report suppression per VLAN

Enabled


Configuring IGMP Snooping

You configure IGMP snooping globally or per VLAN on the Cisco Nexus 3000 Series devices using the IGMP Snooping pane. You can also view the IGMP snooping status per VLAN.


Note If IGMP Snooping is disabled for the device and enabled for specified VLANs, the functionality is disabled for the VLAN as well.
However, if IGMP Snooping is disabled for the VLAN and enabled for the device, the functionality remains disabled for the VLAN.
Report Suppression and IGMPv3 Report Suppression function the same way.


This section contains the following sections:

Configuring IGMP Snooping Global Parameters

Configuring IGMP Snooping Parameters per VLAN

Viewing IGMP Snooping Status per VLAN

Configuring IGMP Snooping Global Parameters

DETAILED STEPS

To set the IGMP snooping parameters for the entire device, follow these steps:


Step 1 From the Feature Selector pane, choose Switching > Multicast > IGMP Snooping to open the IGMP Snooping pane.

Step 2 In the Summary pane, click the device to set the IGMP snooping globally for the entire device.

Step 3 In the Details pane, click the Device Details tab.

Step 4 From the IGMP Snooping drop-down list, choose Enabled or Disabled.

IGMP Snooping is enabled by default.

Step 5 From the Report Suppression drop-down list, choose Enabled or Disabled.

Report Suppression is enabled by default.

Step 6 From the IGMPv3 Report Suppression drop-down list, choose Enabled or Disabled.

IGMPv3 Report Suppression is disabled by default globally for the entire device.

Step 7 From the Link-local Group Suppression drop-down list, choose Enabled or Disabled.

Link-Local Group Suppression is enabled by default.

Step 8 In the Event History Buffer Settings area, from the drop-down lists, choose disabled, small, medium, or large for each of the following:

vPC

IGMP Snoop Internal

MFDM-Sum

MFDM

VLAN

VLAN Events

The default buffer sizes for vPC, IGMP Snoop Internal, MFDM-Sum, and MFDM are small. The default buffer sizes for VLAN and VLAN Events are medium.

Step 9 (Optional) From the menu bar, choose File > Deploy to apply your changes to the device.


Configuring IGMP Snooping Parameters per VLAN

DETAILED STEPS

To set the IGMP snooping parameters per VLAN, follow these steps:


Step 1 From the Feature Selector pane, choose Switching > Multicast > IGMP Snooping to open the IGMP Snooping pane.

Step 2 In the Summary pane, click the device that has the VLANs for which you want to configure IGMP snooping.

Step 3 Click the VLAN for which you want to configure IGMP Snooping.

Step 4 In the Details pane, click the Details tab.

The VLAN ID box displays the VLAN number that you are working on.

Step 5 From the IGMP Snooping drop-down list, choose Enabled or Disabled.

IGMP Snooping is enabled per VLAN by default.

Step 6 From the Report Suppression drop-down list, choose Enabled or Disabled.

Report Suppression is enabled per VLAN by default.

Step 7 From the IGMPv3 Report Suppression drop-down list, choose Enabled or Disabled.

IGMPv3 Report Suppression is enabled per VLAN by default. Once you enable IGMPv3 Report Suppression for the entire device, you do not have to enable that feature for each VLAN.

Step 8 From the Link-local Group Suppression drop-down list, choose Enabled or Disabled.

Link-Local Group Suppression is enabled per VLAN by default.

Step 9 From the Fast Leave drop-down list, choose Enabled or Disabled.

Fast Leave is disabled per VLAN by default.

Step 10 From the Explicit Tracking drop-down list, choose Enabled or Disabled.

Explicit tracking is enabled per VLAN by default.

Step 11 Enter the number of seconds that you want in the Last Member Query Interval field.

The default value for Last Member Query Interval is 1 second for each VLAN, and the maximum value is 25 seconds.

Step 12 (Optional) Enter the IP address for IGMP snooping querier for the switch.

Step 13 (Optional) Right-click in the Static Multicast Group area and choose Add Row or Delete.

a. Click Delete to delete a static multicast group.

b. (Optional) To add a static multicast group, enter the IP address of the multicast source in the Source Address field, the IP address of the multicast group in the Group Address field, and the interface joining the group in the Interface field.


Note Ethernet and port channel are the supported interfaces for this field.


Step 14 (Optional) Right-click in the Static Multicast Router area and choose Add Row or Delete.

a. Click Delete to delete an interface to a static multicast router.

b. To add an interface to the static multicast router, choose the interface from the drop-down list in the Interface field and click OK.


Note Ethernet and port channel are the supported interfaces for this field.


Step 15 (Optional) From the menu bar, choose File > Deploy to apply your changes to the device.


Viewing IGMP Snooping Status per VLAN

To view the status of the IGMP multicast groups, the IGMP multicast routers, the IGMP snooping explicit tracking feature, and the IGMP snooping querier, follow these steps:


Step 1 From the Feature Selector pane, choose Switching > Multicast > IGMP Snooping to open the IGMP Snooping pane.

Step 2 In the Summary pane, click the device that has the VLANs for which you want to configure IGMP snooping.

Step 3 Click the VLAN for which you want to configure IGMP Snooping.

Step 4 In the Details pane, click the Status tab.

Step 5 Click the Multicast Groups section.

The section expands to allow you to Refresh the display and displays the following information for each multicast group discovered using IGMP snooping: Group Address, Source Address, IGMP Version, the Type of multicast group, and the Interfaces that have shown interest in this multicast group.

Step 6 Click the Multicast Routers section.

The section expands to allow you to Refresh the display and displays the following information for each multicast router: Interface connected to the multicast router, Type, Up Time for the entry, and Expiry Time for the entry.

Step 7 Click the Explicit Tracking section.

The section expands to allow you to Refresh the display and displays the following explicit tracking information for each VLAN: Source Address for the multicast traffic, multicast Group Address, Interface that has shown interest in the multicast traffic, Reporter Address of the host machine that has shown interest in the multicast traffic, Up Time for the entry, Last Join Time, and Expiry Time for the entry.

Step 8 Click the Querier section.

The section expands to allow you to Refresh the display and displays the following IGMP snooping information for each VLAN: IP Address of the querier, IGMP Version, Expiry Time for the entry, and Interface on which the querier is discovered.


Configuring IGMP Snooping Parameters

To affect the operation of the IGMP snooping process, you can configure the optional IGMP snooping parameters described in Table 5-2.

Table 5-2 IGMP Snooping Parameters 

Parameter
Description

IGMP snooping

Enables IGMP snooping on the switch or on a per-VLAN basis. The default is enabled.

Note If the global setting is disabled, then all VLANs are treated as disabled, whether they are enabled or not.

Explicit tracking

Tracks IGMPv3 membership reports from individual hosts for each port on a per-VLAN basis. The default is enabled.

Fast leave

Enables the software to remove the group state when it receives an IGMP Leave report without sending an IGMP query message. This parameter is used for IGMPv2 hosts when no more than one host is present on each VLAN port. The default is disabled.

Last member query interval

Sets the interval that the software waits after sending an IGMP query to verify that no hosts that want to receive a particular multicast group remain on a network segment. If no hosts respond before the last member query interval expires, the software removes the group from the associated VLAN port. Values range from 1 to 25 seconds. The default is 1 second.

Snooping querier

Configures a snooping querier on an interface when you do not enable PIM because multicast traffic does not need to be routed.

Report suppression

Limits the membership report traffic sent to multicast-capable routers on the switch or on a per-VLAN basis. When you disable report suppression, all IGMP reports are sent as is to multicast-capable routers. The default is enabled.

Multicast router

Configures a static connection to a multicast router. The interface to the router must be in the selected VLAN.

Static group

Configures a Layer 2 port of a VLAN as a static member of a multicast group.

Link-local groups suppression

Configures link-local groups suppression on the switch or on a per-VLAN basis. The default is enabled.

IGMPv3 report suppression

Configures IGMPv3 report suppression and proxy reporting on the switch or on a per-VLAN basis. The default is disabled for the entire switch and enabled per VLAN.


SUMMARY STEPS

1. configure terminal

2. ip igmp snooping

3. vlan vlan-id

4. ip igmp snooping
ip igmp snooping explicit-tracking
ip igmp snooping fast-leave
ip igmp snooping last-member-query-interval
seconds
ip igmp snooping querier ip-address
ip igmp snooping report-suppression
ip igmp snooping mrouter interface
interface
ip igmp snooping static-group group-ip-addr [source source-ip-addr] interface interface
ip igmp snooping link-local-groups-suppression
ip igmp snooping v3-report-suppression
(Optional) copy running-config startup-config

DETAILED STEPS

 
Command
Purpose

Step 1 

configure terminal

Example:

switch# configure terminal

switch(config)#

Enters configuration mode.

Step 2 

ip igmp snooping

Example:

switch(config)# ip igmp snooping

Enables IGMP snooping. The default is enabled.

Note If the global setting is disabled with the no form of this command, then IGMP snooping on all VLANs is disabled, whether IGMP snooping is enabled on a VLAN or not. If you disable IGMP snooping, Layer 2 multicast frames flood to all modules.

Step 3 

vlan vlan-id

Example:

switch(config)# vlan 2

switch(config-vlan)#

Enters VLAN configuration mode.

Step 4 

ip igmp snooping

Example:

switch(config-vlan)# ip igmp snooping

Enables IGMP snooping for the current VLAN. The default is enabled.

 

ip igmp snooping explicit-tracking

Example:

switch(config-vlan)# ip igmp snooping explicit-tracking

Tracks IGMPv3 membership reports from individual hosts for each port on a per-VLAN basis. The default is enabled on all VLANs.

 

ip igmp snooping fast-leave

Example:

switch(config-vlan)# ip igmp snooping fast-leave

Supports IGMPv2 hosts that cannot be explicitly tracked because of the host report suppression mechanism of the IGMPv2 protocol. When you enable fast leave, the IGMP software assumes that no more than one host is present on each VLAN port. The default is disabled for all VLANs.

 

ip igmp snooping last-member-query-interval seconds

Example:

switch(config-vlan)# ip igmp snooping last-member-query-interval 3

Removes the group from the associated VLAN port if no hosts respond to an IGMP query message before the last member query interval expires. Values range from 1 to 25 seconds. The default is 1 second.

 

ip igmp snooping querier ip-address

Example:

switch(config-vlan)# ip igmp snooping querier 172.20.52.106

Configures a snooping querier when you do not enable PIM because multicast traffic does not need to be routed. The IP address is used as the source in messages.

 

ip igmp snooping report-suppression

Example:

switch(config-vlan)# ip igmp snooping report-suppression

Limits the membership report traffic sent to multicast-capable routers. When you disable report suppression, all IGMP reports are sent as is to multicast-capable routers. The default is enabled.

Note This command can also be entered in global configuration mode to affect all interfaces.

 

ip igmp snooping mrouter interface interface

Example:

switch(config-vlan)# ip igmp snooping mrouter interface ethernet 2/1

Configures a static connection to a multicast router. The interface to the router must be in the selected VLAN. You can specify the interface by the type and the number, such as ethernet slot/port.

 

ip igmp snooping static-group group-ip-addr [source source-ip-addr] interface interface

Example:

switch(config-vlan)# ip igmp snooping static-group 230.0.0.1 interface ethernet 2/1

Configures a Layer 2 port of a VLAN as a static member of a multicast group. You can specify the interface by the type and the number, such as ethernet slot/port.

 

ip igmp snooping link-local-groups-suppression

Example:

switch(config-vlan)# ip igmp snooping link-local-groups-suppression

Configures link-local groups suppression. The default is enabled.

Note This command can also be entered in global configuration mode to affect all interfaces.

 

ip igmp snooping v3-report-suppression

Example:

switch(config-vlan)# ip igmp snooping v3-report-suppression

Configures IGMPv3 report suppression and proxy reporting. The default is disabled for the global command for the entire switch and enabled per VLAN.

Note This command can also be entered in global configuration mode to affect all interfaces.

Step 5 

copy running-config startup-config

Example:

switch(config)# copy running-config startup-config

(Optional) Saves configuration changes.

Verifying the IGMP Snooping Configuration

To display the IGMP snooping configuration information, perform one of the following tasks:

Command
Purpose

show ip igmp snooping [vlan vlan-id]

Displays IGMP snooping configuration by VLAN.

show ip igmp snooping groups [source [group] | group [source]] [vlan vlan-id] [detail]

Displays IGMP snooping information about groups by VLAN.

show ip igmp snooping querier [vlan vlan-id]

Displays IGMP snooping queriers by VLAN.

show ip igmp snooping mroute [vlan vlan-id]

Displays multicast router ports by VLAN.

show ip igmp snooping explicit-tracking [vlan vlan-id]

Displays IGMP snooping explicit tracking information by VLAN.


For detailed information about the fields in the output from these commands, see the Cisco Nexus 3000 Series Command Reference,.

Displaying IGMP Snooping Statistics

You can select and display various statistics for the entire device in the following categories:

IGMP snooping global statistics

IGMP snooping global vPC statistics

You can select and display various statistics per VLAN in the following categories:

IGMP snooping VLAN statistics

IGMP snooping VLAN vPC statistics

Use the show ip igmp snooping statistics vlan command to display IGMP snooping statistics.

Use the clear ip igmp snooping statistics vlan command to clear IGMP snooping statistics.

For detailed information about using these commands, see the Cisco Nexus 3000 Series Command Reference,.

Configuration Examples for IGMP Snooping

This example shows how to configure the IGMP snooping parameters:

configure terminal
  ip igmp snooping
  vlan 2
    ip igmp snooping
    ip igmp snooping explicit-tracking
    ip igmp snooping fast-leave
    ip igmp snooping last-member-query-interval 3
    ip igmp snooping querier 172.20.52.106
    ip igmp snooping report-suppression
    ip igmp snooping mrouter interface ethernet 2/1
    ip igmp snooping static-group 230.0.0.1 interface ethernet 2/1
    ip igmp snooping link-local-groups-suppression
    ip igmp snooping v3-report-suppression
   

Where to Go Next

You can enable the following features that work with PIM:

Chapter 3 "Configuring IGMP"

Chapter 6 "Configuring MSDP"

Field Descriptions for Configuring IGMP Snooping

This section describes the fields shown on the IGMP Snooping pane and includes the following:

Device: Device Details Tab

VLANs: Details Tab

VLANs: Status Tab

Device: Device Details Tab

Table 5-3 Device: Device Details Tab 

Element
Description

IGMP Snooping

Status of IGMP snooping. The range is enabled or disabled, and the default value is enabled.

Report Suppression

Status of report suppression. The range is enabled or disabled, and the default is enabled.

IGMPv3 Report Suppression

Status of IGMPv3 report suppression. The range is enabled or disabled, and the default is disabled.

Link-local Group Suppression

Status of the link-local group suppression. The range is enabled or disabled, and the default is enabled.

Event History Buffer Settings

Type

Type of event history buffer. The types and the defaults are as follows:

vPC—small

IGMP Internal Snoop—small

MFDM-Sum—small

MFDM—small

VLAN—medium

VLAN Events—medium

Size

Size and status of the event history buffer. The valid values are as follows:

disabled

small

medium

large


VLANs: Details Tab

Table 5-4 VLANs: Details Tab 

Element
Description

VLAN ID

Display only. VLAN number.

IGMP Snooping

Status of IGMP snooping. The range is enabled and disabled. The default is enabled.

Report Suppression

Status of report suppression. The range is enabled and disabled. The default is enabled.

IGMPv3 Report Suppression

Status of IGMPv3 report suppression. The range is enabled and disabled.

Link-local Group Suppression

Status of link-local group suppression. The range is enabled and disabled,.

Fast Leave

Status of fast leave. The range is enabled or disabled, and the default is disabled.

Explicit Tracking

Status of explicit tracking. The range is enabled or disabled, and the default is enabled.

Last Member Query Interval

Last member query interval in seconds. The range is 1 to 25, and the default is 1 second.

Switch Querier

IP address for the IGMP snooping switch querier.

Static Multicast Group

Source Address

IP address of the multicast source.

Group Address

IP address of the multicast group.

Interface

Interface on which the multicast group or source is configured.

Static Multicast Router

Interface

Interface on which the multicast router is configured.


VLANs: Status Tab

Table 5-5 VLANs: Status Tab 

Element
Description
Multicast Group

Group Address

Display only. IP address of the multicast group discovered by IGMP snooping.

Source Address

Display only. IP address of the multicast source.

IGMP Version

Display only. IGMP version. Valid values are as follows:

v1

v2

v3

Type

Display only. Type of discovered multicast group address discovered. Valid values are as follows:

S—static

D—dynamic

R—router port

Interface

Display only. List of interfaces that have shown interest in the multicast group.

Multicast Routers

Interface

Display only. Interface connected to the multicast router.

Type

Display only. Type of multicast address. Valid values are as follows:

S—static

D—dynamic

V—vPC peer link

I—internal

Up Time

Display only. Time the entry has been up.

Expiry Time

Display only. Time at which this entry expires.

Explicit Tracking

Source Address

Display only. IP address of the source for the multicast traffic.

Group Address

Display only. IP address for the multicast group.

Interface

Display only. Interface that has shown interest in receiving the multicast traffic.

Reporter Address

Display only. Host machine that has shown interest in receiving the multicast traffic.

Up Time

Display only. Length of time that the entry has been up.

Last Join Time

Display only. Time at which this entry was added.

Expiry Time

Display only. Time at which this entry expires.

Querier

Querier Address

Display only. IP address of the IGMP snooping querier.

IGMP Version

Display only. IGMP version. Valid values are as follows:

v1

v2

v3.

Expiry Time

Display only. Time at which this entry expires.

Interface

Display only. Interface on which the querier is defined or discovered.

Note The value is Self when the local device is the IGMP snooping querier.


Additional References

For additional information related to implementing IGMP snooping, see the following sections:

Related Documents

Standards

Feature History for IGMP Snooping

Feature History for IGMP Snooping in GUI

Related Documents

Related Topic
Document Title

CLI commands

Cisco Nexus 3000 Series Command Reference,


Standards

Standards
Title

No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.


Feature History for IGMP Snooping

Table 5-6 lists the release history for this feature.

Table 5-6 Feature History for IGMP Snooping

Feature Name
Releases
Feature Information

IGMP Snooping

5.0(3)U1(1)

This feature was introduced.


Feature History for IGMP Snooping in GUI

Table 5-7 lists the release history for this feature.

Table 5-7 Feature History for IGMP Snooping

Feature Name
Releases
Feature Information

IGMP Snooping

5.0(1)

Introduced.