Cisco Nexus 1010 Software Configuration Guide, Release 4.2(1)SP1(3)
VSB Backup and Recovery
Downloads: This chapterpdf (PDF - 238.0KB) The complete bookPDF (PDF - 3.39MB) | Feedback

VSB Backup and Recovery

Table Of Contents

VSB Backup and Recovery

Information About VSB Backup and Recovery

Guidelines and Limitations

Configuring VSB Backup and Restoration

Flowchart: Backing Up and Restoring a VSB Configuration

Exporting a Backup VSB Configuration

Creating a VSB Backup File

Copying the VSB Backup File to External Storage

Importing a VSB Backup File

Recovering a VSM with a Backup Configuration File

Verifying the Backup and Recovery

Additional References

Related Documents

Standards

MIBs

RFCs

Feature History for Export and Import


VSB Backup and Recovery


This chapter describes how to backup and recover a VSB, and includes the following sections:

Information About VSB Backup and Recovery

Guidelines and Limitations

Configuring VSB Backup and Restoration

Verifying the Backup and Recovery

Additional References

Feature History for Export and Import

Information About VSB Backup and Recovery

You can create a backup copy of a VSB and store it remotely to use as a recovery mechanism or when you need to move a VSB between Cisco Nexus 1010s.

Figure 7-1 shows the process for backig up and recovering a VSB.

Guidelines and Limitations

The following are guidelines and limitations to use when backing up and recovering a VSB:

Multiple export files may be created with this process. Do not change the file suffix for numbering purposes. If you change the prefix for one file, then you must change it for all.

You must shut down the VSB before creating the file to export.

The bootflash: export-import directory must be empty prior to either creating an export file or copying the file back from external storage.

Configuring VSB Backup and Restoration

This section includes the following topics and procedures:

Flowchart: Backing Up and Restoring a VSB Configuration

Exporting a Backup VSB Configuration

Importing a VSB Backup File

Recovering a VSM with a Backup Configuration File

Flowchart: Backing Up and Restoring a VSB Configuration

You can use the following process for backing up and restoring a VSB configuration.

Figure 7-1 Flow Chart: Backing Up and Restoring a VSB Configuration

Exporting a Backup VSB Configuration

You can use the following procedures to create a backup copy of a VSB, store it remotely, and then re-import it to either recover a VSM or move a VSB between Cisco Nexus 1010s.

Creating a VSB Backup File

Copying the VSB Backup File to External Storage

Creating a VSB Backup File

You can use this procedure to create a file for exporting a VSB.

BEFORE YOU BEGIN

Before beginning this procedure, you must know or do the following:

You are logged in to the CLI of the Cisco Nexus 1010 in EXEC mode.

You know the name of the VSB for which you are creating a file to export.

You have verified that the bootflash: export-import directory is empty. If files are present in this directory, you must delete them before starting this procedure.

You must shut down the VSB that you want to backup before creating the file to export. This procedure includes a step for shutting down the VSB and then a step to restart the VSB after creating the file.


Note Multiple files may be created. Do not change the file suffix for numbering purposes. If you change the prefix for one file, then you must change it for all.


SUMMARY STEPS

1. dir export-import

2. (Optional) delete filename

3. config t

4. virtual-service-blade name

5. shutdown [primary | secondary]

6. show virtual-service-blade summary

7. export [primary | secondary]

8. dir bootflash:export-import

9. no shutdown [primary | secondary]

10. show virtual-service-blade summary

DETAILED STEPS

 
Command
Purpose

Step 1 

dir export-import

Example:

n1010# dir export-import

DOCS-CPPA# dir export-import

Usage for bootflash://sup-local

496164864 bytes used

3495215104 bytes free

3991379968 bytes total

n1010#

Displays the contents of the export-import directory for verification that the directory is empty.

If there is anything in this directory, you must use the next step to delete it before proceeding.

Step 2 

delete filename

Example:

n1010-1(config-vsb-config)# delete bootflash:/export-import/1/*.*

n1010-1(config-vsb-config)# delete bootflash:/export-import/1

n1010-1(config-vsb-config)#

Deletes the contents of the folder and the parent folder.

Note Do not delete the export-import folder.

Step 3 

config t

Example:

n1010-1# config t

n1010-1(config)#

Enters CLI  Global Configuration mode.

Step 4 

virtual-service-blade name

Example:

n1010-1(config)# virtual-service-blade vsm-1

n1010-1(config-vsb-config)#

Enters configuration mode for the named virtual service blade.

Step 5 

shutdown [primary | secondary]

Example:

n1010-1(config-vsb-config)# shutdown secondary

n1010-1(config-vsb-config)#

Shuts down the VSB you are exporting from.

If a redundant pair of Cisco Nexus 1010s, you must specify whether to shut down the primary or secondary.

Step 6 

show virtual-service-blade summary

Displays the virtual service blade configuration for verification.

 

Example:

n1010-1(config-vsb-config)# show virtual-service-blade summary

-------------------------------------------------------------------------------

Name Role State Nexus1010-Module

-------------------------------------------------------------------------------

VSM1 PRIMARY VSB POWERED ON Nexus1010-PRIMARY

VSM1 SECONDARY VSB POWERED OFF Nexus1010-SECONDARY

Step 7 

export [primary | secondary]

Example:

n1010-1(config-vsb-config)# export secondary

Note: export started..

Note: please be patient..

Note: please be patient..

Note: please be patient..

Note: export completed...n1010-1(config-vsb-config)#

Example:

n1010-1(config-vsb-config)# export primary

ERROR: Please clean export-import directory first, then proceed.

n1010-1(config-vsb-config)#

Example:

n1010-1(config-vsb-config)# export secondary

ERROR: Cannot export active virtual-service-blade, please shut and retry.

Creates a directory named for the slot id of the exported VSB containing a compressed tar image of the VSB.

If exporting from a redundant pair of Cisco Nexus 1010s, you must specify whether exporting from the primary or secondary.

Note The export command does not move the configuration file off of the Cisco Nexus 1010. The export command creates a backup copy that you must then copy to remote storage. There is a separate procedure for this.

Step 8 

dir bootflash:export-import

Example:

n1010-1(config-vsb-config)# dir bootflash:export-import

     4096      Sep 08 19:12:52 2011 1/

Usage for bootflash://sup-local

310870016 bytes used

3680509952 bytes free

3991379968 bytes total

Displays the contents of the bootflash: export-import directory, including the directory name of the folder containing the compressed tar image of the VSB, for verification.

Note You need this folder name in Step 11.

Step 9 

no shutdown [primary | secondary]

Example:

n1010-1(config-vsb-config)# no shutdown secondary

n1010-1(config-vsb-config)#

Powers on the VSB that was powered off when creating the file for export.

If a redundant pair of Cisco Nexus 1010s, you must specify primary or secondary.

Step 10 

show virtual-service-blade summary

Displays the virtual service blade configuration for verification.

 

Example:

n1010-1(config-vsb-config)# show virtual-service-blade summary

-------------------------------------------------------------------------------

Name Role State Nexus1010-Module

-------------------------------------------------------------------------------

VSM1 PRIMARY VSB POWERED ON Nexus1010-PRIMARY

VSM1 SECONDARY VSB POWERED ON          Nexus1010-SECONDARY

Step 11 

dir bootflash:export-import
/
directory-name

Example:

n1010-1(config-vsb-config)# dir bootflash:export-import/1

279955021 Sep 08 19:13:21 2011 Vdisk1.img.tar.00

Usage for bootflash://sup-local

310870016 bytes used

3680509952 bytes free

3991379968 bytes total

Displays the contents of the Cisco Nexus 1010 export folder, including the filename of the VSB compressed tar image.

Note You identified this folder name in Step 8.

Note Multiple files may be created. Do not change the file suffix for numbering purposes. If you change the prefix for one file, then you must change it for all.

Copying the VSB Backup File to External Storage

Use this procedure to copy a VSB configuration file to remote storage and then delete the folder created for this purpose from the Cisco Nexus 1010.

BEFORE YOU BEGIN

Before beginning this procedure, you must know or do the following:

You have created a file to export using the "Creating a VSB Backup File" procedure and you know the name of this file and the name of the folder it resides in.


Note Multiple files may be created. If so, use the first filename in this procedure. Do not change the file suffix for numbering purposes. If you change the prefix for one file, then you must change it for all.


You are logged in to the CLI of the Cisco Nexus 1010 in EXEC mode.

You know name of the path to a remote storage location.

After copying the export backup file, delete the contents, including files and folders, of the export-import directory. Do not delete the export-import folder.

SUMMARY STEPS

1. copy bootflash:export-import/folder-name/filename ftp:

2. cd /export-import/folder-name

3. delete filename

4. dir

DETAILED STEPS

 
Command
Purpose

Step 1 

copy bootflash:export-import
/folder-name/filename ftp:

Example:

n1010# copy bootflash:export-import/1/Vdisk1.img.tar .00 ftp:

Enter vrf (If no input, current vrf 'default' is considered):

Enter hostname for the ftp server: 10.78.109.51

Enter username: administrator

Password:

***** Transfer of file Completed Successfully *****

n1010#

Copies the VSB image from the Cisco Nexus 1010 export-import folder to remote storage.

Step 2 

cd /export-import

Example:

n1010## cd /export-import

n1010##

Changes to the export-import directory.

Step 3 

delete filename

Example:

n1010# delete bootflash:/export-import/1/Vdisk1.img.ta r.00

n1010# delete bootflash:/export-import/1

n1010#

Deletes the VSB compressed tar file created for export.

Step 4 

dir

Example:

n1010# dir

n1010#

Displays the contents of the export-import directory for verification.

Importing a VSB Backup File

You can use the following procedure to import a previously-saved backup copy of a VSB from remote storage to the Cisco Nexus 1010.

BEFORE YOU BEGIN

You are logged in to the CLI of the active Cisco Nexus 1010 in EXEC mode.

You have previously created and saved a copy of the Cisco Nexus 1010 configuration in a remote storage location using the "Exporting a Backup VSB Configuration" procedure.


Note Multiple files may be created. If so, use only the first filename with the import command. Do not change the file suffix for numbering purposes. If you change the prefix for one file, then you must change it for all.


You know the name of the VSB and the path to the remote storage location.

You have verified that the bootflash: export-import directory is empty. If files are present in this directory, you must delete them before importing a VSB configuration file.

If an imported VSB role does not match the role of the Nexus1010 on which it is imported, then the VSB role should be changed internally to match the Nexus1010 role.

SUMMARY STEPS

1. dir export-import

2. (Optional) delete filename

3. copy ftp:filename bootflash:export-import

4. config t

5. virtual-service-blade name

6. import [primary | secondary] filename

7. show virtual-service-blade summary

8. show virtual-service-blade name name

9. copy running-config startup-config

DETAILED STEPS

 
Command
Purpose

Step 1 

dir export-import

Example:

n1010# dir export-import

DOCS-CPPA# dir export-import

Usage for bootflash://sup-local

496164864 bytes used

3495215104 bytes free

3991379968 bytes total

n1010#

Displays the contents of the export-import directory for verification that the directory is empty.

If there is anything in this directory, you must use the next step to delete it before proceeding.

Step 2 

(Optional) delete filename

Example:

n1010-1(config-vsb-config)# delete Vdisk1.img.tar.00

n1010-1(config-vsb-config)#

Deletes the contents of the folder.

 

Step 3 

copy ftp:filename bootflash:export-import

Example:

n1010# copy ftp:Vdisk1.img.tar.00 bootflash:export-import

Enter vrf (If no input, current vrf 'default' is considered):

Enter hostname for the ftp server: 10.78.109.51

Enter username: administrator

Password:

***** Transfer of file Completed Successfully *****

Copies the exported image file from remote storage into the Cisco Nexus 1010 export-import folder in the bootflash: repository.

fiename: The name of the export file. Multiple files may have been created. If so, use only the first filename with the import command. Do not change the file suffix for numbering purposes. If you change the prefix for one file, then you must change it for all.

Step 4 

config t

Example:

n1010-1# config t

n1010-1(config)#

Enters CLI  Global Configuration mode.

Step 5 

virtual-service-blade name

Example:

n1010-1(config)# virtual-service-blade vsm-5

n1010-1(config-vsb-config)#

Enters configuration mode for the named virtual service blade.

Step 6 

import primary filename

Example:

n1010-1(config-vsb-config)# import primary Vdisk1.img.tar.00

Note: import started..

Note: please be patient..

Note: Import cli returns check VSB status for completion

n1010-1(config-vsb-config)#

Powers off the primary VSB, imports the specified VSB configuration file, and then removes the configuration file from the export-import folder.

fiename: The name of the export file that you copied from the remote server to the bootflash: repository.

Step 7 

show virtual-service-blade summary

Displays a summary of all virtual service blade configurations by type name, such as VSM or NAM.

Verify that the primary VSB is powered off.

 

Example:

n1010-1(config-vsb-config)# show virtual-service-blade summary

-------------------------------------------------------------------------------

Name Role State Nexus1010-Module

-------------------------------------------------------------------------------

VSM1                PRIMARY VSB POWERED OFF Nexus1010-PRIMARY

VSM1                SECONDARY   VSB POWERED ON           Nexus1010-SECONDARY

Step 8 

show virtual-service-blade name name

Displays the virtual service blade information for verification.

From the command output, make a note of the control and management VSB Ethernet interfaces.

 

Example:

n1010-1(config-vsb-config)# show virtual-service-blade name VSM1

virtual-service-blade VSM1

Description:

Slot id: 1

Host Name:

Management IP:

VSB Type Name : VSM-1.1

vCPU: 1

Ramsize: 2048

Disksize: 3

Heartbeat: 0

HA Admin role: Primary

HA Oper role: NONE

Status: VSB POWERED OFF

Location: PRIMARY

SW version:

VsbEthernet1/1/1: control vlan: 1306 state: up

VsbEthernet1/1/2: management vlan: 1304 state: up

VsbEthernet1/1/3: packet vlan: 1307 state: up

Interface: internal vlan: NA state: up

HA Admin role: Secondary

HA Oper role: NONE

Status: VSB POWERED ON

Location: SECONDARY

SW version:

VSB Info:

n1010-1(config-vsb-config)#

Step 9 

copy running-config startup-config

Example:

n1010-1(config-vsb-config)# copy running-config startup-config

Saves the running configuration persistently through reboots and restarts by copying it to the startup configuration.

Recovering a VSM with a Backup Configuration File

You can use this procedure to recover a VSM using a backup configuration file.

BEFORE YOU BEGIN

Before beginning this procedure, you must know or do the following:

You have imported your backup copy of the configuration file using the "Importing a VSB Backup File" procedure.

You have a copy of the VSM running configuration in remote storage.

You are logged in to the CLI of the Cisco Nexus 1010 in EXEC mode.

This procedure includes a step for updating Cisco Nexus 1000V licenses. For more information, see the Cisco Nexus 1000V License Configuration Guide, Release 4.2(1)SV1(4a).

This procedure requires you to shutdown the VSM management and control ports to prevent communication with VEMs and vCenter during the recovery. You need to know the IDs of the VSM control and management ports and the VSB serial port.

This procedure requires you to setup the VSM software. You need to have the following information available for the VSM VSB:

Admin password

Domain ID

HA Role (must be set to the same role as that of the VSM on which it is imported)

Management 0 IP address

Management 0 netmask

Default gateway IP address

For detailed information about setting up the VSM software, see the Cisco Nexus 1000V Getting Started Guide, Release 4.2(1)SV1(4a)

For detailed information about the vCenter server connection, see the


Step 1 From the Cisco Nexus 1010, shut down the control and management interfaces of the VSM VSB.

config t
interface vethernet slot/port 
shut
 
   
Example:

n1010-1# config t

n1010-1(config)# interface vethernet1/1

n1010-1(config-if)# shut
 
   

The VSM management and control interfaces are no longer communicating with VEMs and vCenter.

Step 2 Verify that the control and management interfaces are down.

show virtual-service-blade name name

Example:

n1010-1(config)# show virtual-service-blade name VSM1

virtual-service-blade VSM1

Description:

Slot id: 1

Host Name:

Management IP:

VSB Type Name : VSM-1.1

vCPU: 1

Ramsize: 2048

Disksize: 3

Heartbeat: 0

HA Admin role: Primary

HA Oper role: NONE

Status: VSB POWERED OFF

Location: PRIMARY

SW version:

VsbEthernet1/1/1: control vlan: 1306 state: down

VsbEthernet1/1/2: management vlan: 1304 state: down

VsbEthernet1/1/3: packet vlan: 1307 state: up

Interface: internal vlan: NA state: up

HA Admin role: Secondary

HA Oper role: NONE

Status: VSB POWERED ON

Location: SECONDARY

SW version:

VSB Info:

n1010-1(config)#

Step 3 Power on the VSB VSM.

virtual-service-blade name
no shutdown [primary | secondary]

Example:

n1010-1(config)# virtual-service-blade VSM1

n1010-1(config)# no shutdown primary

n1010-1(config)#

Step 4 Log in to Cisco Nexus 1010 serial port of the primary VSM.

Step 5 Erase the startup configuration.

config t
write erase

Example:

n1000v# config t

n1000v(config)# write erase
Warning: This command will erase the startup-configuration.
Do you wish to proceed anyway? (y/n)  [n] y
 
   

The previous configuration is erased. You will replace it with the previously-saved backup of your running configuration in Step 11.

Step 6 Reboot the system.

reload

n1000v# reload
This command will reboot the system. (y/n)? [n] y
2009 Oct 30 21:51:34 s1 %$ VDC-1 %$ %PLATFORM-2-PFM_SYSTEM_RESET: Manual system restart 
from Command Line Interface
n1000v#
 
   

The Cisco Nexus 1010 boots up and the setup wizard starts.

Step 7 Use the setup wizard to configure the VSM. Accept defaults for all except the following:

Admin password

Domain ID

HA Role (must be set to the same role as that of the VSM on which it is imported)

Management 0 IP address

Management 0 netmask

Default gateway IP address

Example:
---- System Admin Account Setup ----
Enter the password for "admin": 
Confirm the password for "admin": 
Enter the domain id<1-4095>: 152 
Enter HA role[standalone/primary/secondary]: primary 
 
   
[#########################################] 100% 
 
   
         ---- Basic System Configuration Dialog ----
This setup utility will guide you through the basic configuration of
the system. Setup configures only enough connectivity for management
of the system.
*Note: setup is mainly used for configuring the system initially,
when no configuration is present. So setup always assumes system
defaults and not the current system configuration values.
Press Enter at anytime to skip a dialog. Use ctrl-c at anytime
to skip the remaining dialogs.
Would you like to enter the basic configuration dialog (yes/no): yes
Create another login account (yes/no) [n]: no
Configure read-only SNMP community string (yes/no) [n]: no
Configure read-write SNMP community string (yes/no) [n]: no
Enter the switch name: n1000v
Continue with Out-of-band (mgmt0) management configuration? [yes/no] [y]: yes 
Mgmt0 IPv4 address: 172.28.15.152 
Mgmt0 IPv4 netmask: 255.255.255.0
Configure the default-gateway: (yes/no) [y]: yes  
 
   
            IPv4 address of the default gateway : 172.23.233.1
Enable the telnet service? (yes/no) [y]: no
Enable the ssh service? (yes/no) [y]: no 
Enable the http-server? (yes/no) [y]: no
Configure NTP server? (yes/no) [n]: no
Configure svs domain parameters? (yes/no) [y]: no
Vem feature level will be set to 4.2(1)SV1(4),  
Do you want to reconfigure? (yes/no) [n] no
 
   

The system summarizes the new setup configuration.

Step 8 Copy the running configuration to the startup configuration.

copy running-config startup-config

Example:

n1000v# copy running-config startup-config

[########################################] 100%

n1000v#

Step 9 Reopen the management interface of the VSM VSB.

config t
interface vethernet slot/port 
no shut
 
   
Example:

n1010-1# config t

n1010-1(config)# interface vethernet1/2

n1010-1(config-if)# no shut
 
   
 
   

The VSM management interface is again communicating with VEMs and vCenter.

Step 10 Verify that the management interface is up.

show virtual-service-blade name name

Example:

n1010-1(config)# show virtual-service-blade name VSM1

virtual-service-blade VSM1

. . .

VsbEthernet1/1/1: control vlan: 1306 state: down

VsbEthernet1/1/2: management vlan: 1304 state: up

VsbEthernet1/1/3: packet vlan: 1307 state: up

Interface: internal vlan: NA state: up

. . .

n1010-1(config)#

Step 11 Copy your saved running configuration backup to the VSM bootflash.

copy bootflash:filename

Example: 
n1010-1(config)# copy bootflash:VSM1-periodic-startup-config.txt running-config
n1010-1(config)# 
 
   

Step 12 Copy the running configuration to the startup configuration.

copy running-config startup-config

Example:

n1000v# copy running-config startup-config

[########################################] 100%

n1000v#

 
   

Step 13 Reopen the control interface of the VSM VSB.

config t
interface vethernet slot/port 
no shut
 
   
Example:

n1010-1# config t

n1010-1(config)# interface vethernet1/1

n1010-1(config-if)# no shut
 
   
 
   

The VSM control interface is again communicating with VEMs and vCenter.

Step 14 Verify that the control interface is up.

show virtual-service-blade name name

Example:

n1010-1(config)# show virtual-service-blade name VSM1

virtual-service-blade VSM1

. . .

VsbEthernet1/1/1: control vlan: 1306 state: up

VsbEthernet1/1/2: management vlan: 1304 state: up

VsbEthernet1/1/3: packet vlan: 1307 state: up

Interface: internal vlan: NA state: up

. . .

n1010-1(config)#

Step 15 Check the modules by entering the show module command at the VSM CLI.

Example:

n1000v(config)# show module

Mod Ports Module-Type                      Model              Status

--- ----- -------------------------------- ------------------ ------------

1   0     Virtual Supervisor Module        Nexus1000V         active *

2   0     Virtual Supervisor Module        Nexus1000V         ha-standby

3   248   Virtual Ethernet Module          NA                 ok

4   248   Virtual Ethernet Module          NA                 ok

Mod Sw               Hw

--- ---------------- ------------------------------------------------

1   4.2(1)SV1(4a)    0.0

2   4.2(1)SV1(4a)    0.0

3   4.2(1)SV1(4a)    VMware ESXi 4.0.0 Releasebuild-208167 (1.9)

4   4.2(1)SV1(4a)    VMware ESX 4.1.0 Releasebuild-260247 (2.0)

Mod MAC-Address(es) Serial-Num

--- -------------------------------------- ----------

1 00-19-07-6c-5a-a8 to 00-19-07-6c-62-a8 NA

2 00-19-07-6c-5a-a8 to 00-19-07-6c-62-a8 NA

3 02-00-0c-00-03-00 to 02-00-0c-00-03-80 NA

4 02-00-0c-00-04-00 to 02-00-0c-00-04-80 NA

Mod Server-IP       Server-UUID                          Server-Name

--- --------------- ------------------------------------ --------------------

1   10.78.109.44    NA                                   NA

2   10.78.109.44    NA                                   NA

3   10.78.109.72    44454c4c-4300-1046-8043-b6c04f563153 10.78.109.72

4   10.78.109.71    44454c4c-3300-1056-8057-b3c04f583153 10.78.109.71

* this terminal session

n1000v(config)#

Step 16 Enable the HA peer.

enable [primary | secondary]

Example:

n1010-1(config)# enable secondary

The VSM is again operating in HA mode with a primary and secondary module.

Step 17 You have completed this procedure.


Verifying the Backup and Recovery

To verify the backup and recovery, use the following commands:

Command
Purpose

dir bootflash:export-import /folder-name

Displays the contents of the export-import directory folder.

show virtual-service-blade summary

Displays the redundancy state (active or standby) and the redundancy role (primary or secondary) for each VSB.

Note This command is only recognized by the active Cisco Nexus 1010.

See Example 7-2

show virtual-service-blade [name name]

Displays the configuration for a specific virtual service blade.

See Example 7-3


Example 7-1 export-import directory

n1010-1(config-vsb-config)# dir bootflash:export-import/1

279955021 Sep 08 19:13:21 2011 Vdisk1.img.tar.00

Usage for bootflash://sup-local

310870016 bytes used

3680509952 bytes free

3991379968 bytes total

Example 7-2 Virtual Service Blade Summary

n1010-1(config-vsb-config)# show virtual-service-blade summary

-------------------------------------------------------------------------------

Name Role State Nexus1010-Module

-------------------------------------------------------------------------------

VSM1                PRIMARY VSB POWERED OFF Nexus1010-PRIMARY

VSM1                SECONDARY   VSB POWERED ON           Nexus1010-SECONDARY

Example 7-3 Virtual Service Blade

n1010# show virtual-service-blade name VSM1

virtual-service-blade VSM1

Description:

Slot id: 1

Host Name:

Management IP:

VSB Type Name : VSM-1.1

vCPU: 1

Ramsize: 2048

Disksize: 3

Heartbeat: 0

HA Admin role: Primary

HA Oper role: NONE

Status: VSB POWERED OFF

Location: PRIMARY

SW version:

VsbEthernet1/1/1: control vlan: 1306 state: down

VsbEthernet1/1/2: management vlan: 1304 state: down

VsbEthernet1/1/3: packet vlan: 1307 state: up

Interface: internal vlan: NA state: up

HA Admin role: Secondary

HA Oper role: NONE

Status: VSB POWERED ON

Location: SECONDARY

SW version:

VSB Info:

n1010-1(config)#

Additional References

For additional information related to implementing system-level HA features, see the following sections:

Related Documents

Standards

MIBs

RFCs

Related Documents

Related Topic
Document Title

Software setup configuration

Setting Up the Management Software

Virtual service configuration

Configuring Virtual Service Blades

Cisco Nexus 1010 installation

Cisco Nexus 1010 Virtual Services Appliance Hardware Installation Guide

Complete command syntax, command modes, command history, defaults, usage guidelines, and examples for all Cisco Nexus 1010 commands.

Cisco Nexus 1010 Command Reference, Release 4.2(1)SP1(2)


Standards

Standards
Title

No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.


MIBs

MIBs
MIBs Link

No MIBs are supported by this feature

 

RFCs

RFCs
Title

No RFCs are supported by this feature


Feature History for Export and Import

This section provides the export and import feature release history.

Feature Name
Releases
Feature Information

VSB export and import

4.2(1)SP1(3)

This feature was introduced.