Cisco NAC Appliance - Clean Access Manager Configuration Guide, Release 4.7(5)
Wireless LAN Controller Management: Configuring Wireless Out-of-Band Deployment
Downloads: This chapterpdf (PDF - 540.0KB) The complete bookPDF (PDF - 18.67MB) | Feedback

Wireless LAN Controller Management: Configuring Wireless Out-of-Band Deployment

Table Of Contents

Wireless LAN Controller Management: Configuring Wireless Out-of-Band Deployment

Overview

Wireless In-Band Versus Out-of-Band

Wireless Out-of-Band Requirements

SNMP Control

Summary Steps to Configure Wireless Out-of-Band

Wireless Out-of-Band Virtual Gateway Deployment

Login and Authentication Flow in Wireless OOB Virtual Gateway Mode

Configure Your Network for Wireless Out-of-Band

Configure Your Wireless LAN Controllers

Wireless LAN Controllers Configuration Notes

Example Wireless LAN Controller Configuration Steps

Create the Dynamic Interface on the Wireless LAN Controller

Create the WLAN on the Wireless LAN Controller and Enable Cisco NAC Appliance Integration

Configure SNMP on the Wireless LAN Controller

Specify the CAM as the SNMP Trap Receiver

Wireless OOB Network Setup/Configuration Worksheet

Configure Wireless LAN Controller Connection on the CAM

Add a Wireless Out-of-Band Clean Access Server and Configure Environment

Configure Group Profiles

Add Group Profile

Edit Group Profile

Configure Wireless LAN Controller Profiles

Add Wireless LAN Controller Profile

Configure SNMP Receiver

SNMP Trap

Add and Manage Wireless LAN Controllers

Add New Wireless LAN Controller

Search New Wireless LAN Controllers

Discovered Wireless Clients

Config Tab

View Wireless Out-of-Band Online Users

Wireless Out-of-Band Users

Wireless OOB User Sessions

Wireless and Wired OOB User List Summary


Wireless LAN Controller Management: Configuring Wireless Out-of-Band Deployment


This chapter describes how to configure Cisco NAC Appliance for Wireless Out-of-Band (Wireless OOB) deployment. Topics include:

Overview

Wireless Out-of-Band Virtual Gateway Deployment

Configure Your Network for Wireless Out-of-Band

Configure Your Wireless LAN Controllers

Configure Wireless LAN Controller Connection on the CAM

Wireless Out-of-Band Users

See Cisco NAC Appliance - Clean Access Server Configuration Guide, Release 4.7(5) for additional information on OOB deployments.

Overview

In a traditional in-band Cisco NAC Appliance wireless deployment, all network traffic to or from wireless client machines passes through the Clean Access Server (CAS). For high throughput or highly routed environments, a Cisco NAC Appliance Wireless Out-of-Band (Wireless OOB) deployment allows client traffic to pass through the network only in order to be authenticated and certified before being connected directly to the access network. This section discusses the following topics:

Wireless In-Band Versus Out-of-Band

Wireless Out-of-Band Requirements

SNMP Control

Summary Steps to Configure Wireless Out-of-Band

Wireless In-Band Versus Out-of-Band

Table 4-1 summarizes different characteristics of each type of deployment.

Table 4-1 Wireless In-Band vs. Out-of-Band Deployment  

Wireless In-Band Deployment Characteristics
Wireless Out-of-Band Deployment Characteristics

The Clean Access Server (CAS) is always inline with user traffic (both before and following authentication, posture assessment and remediation). Enforcement is achieved through being inline with traffic.

The Clean Access Server (CAS) is inline with user traffic only during the process of authentication, assessment and remediation. Following that, user traffic does not come to the CAS. Enforcement is achieved through the use of SNMP to coordinate with Wireless LAN Controllers (WLCs) and to assign/reassign VLAN assignments.

The CAS can be used to securely control authenticated and unauthenticated user traffic.

The CAS can control user traffic during the authentication, assessment and remediation phase, but cannot do so post-remediation since the traffic is Out-of-Band.

Bandwidth restricted to maximum allowable throughput for installed Clean Access Server(s).

Out-of-Band bandwidth not restricted by Clean Access Servers in network, as all client traffic bypasses CASs once clients are authenticated.


Wireless Out-of-Band Requirements

Wireless Out-of-band implementation of Cisco NAC Appliance requires the following to be in place:

Cisco Wireless LAN Controllers must be supported models that use at least the minimum supported version of IOS (supporting SNMP traps). See Table 4-2.

Cisco Wireless LAN Controllers must be Layer 2 adjacent to the Clean Access Server(s) with which they interoperate to support wireless client login.

Clean Access Servers supporting wireless client login and authentication must be installed and configured in Virtual Gateway mode.


Note Administrators can update the object IDs (OIDs) of supported WLCs through CAM updates (under Device Management > Clean Access > Updates > Summary | Settings). For example, if a new WLC of a supported model (Cisco 4400 Series) is released, administrators only need to perform Cisco Updates on the CAM to obtain support for the WLC OIDs, instead of performing a software upgrade of the CAM/CAS.

The update WLC OID feature only applies to existing models. If a new WLC series is introduced, administrators will still need to upgrade to ensure Wireless OOB support for the new WLCs. See Configure and Download Updates.

Note The supported mode of HREAP in Cisco NAC Wireless Out-Of-Band is central authentication, central switching. In this state, the controller handles client authentication, and all client data is tunneled back to the controller. This state is valid only in connected mode.
Local Switching is not supported with Cisco NAC Wireless OOB.

Note For the most current details on WLC model/IOS version support, refer to Switch Support for Cisco NAC Appliance.

Table 4-2 Supported Wireless LAN Controller Models

Supported Wireless LAN Controllers
Wireless LAN Controller Release
Cisco NAC Appliance Release

Cisco 4400 Series Wireless LAN Controllers

5.1 and later

4.7

Cisco 2000 Series Wireless LAN Controllers

Cisco Catalyst 3750G Integrated Wireless LAN Controller

Cisco Catalyst 6500/7600 Series Wireless Services Module (WiSM)

Cisco Wireless LAN Controller Module


SNMP Control

In a Wireless OOB deployment, you can add WLCs to the Clean Access Manager's domain and communicate with the WLC using the Simple Network Management Protocol (SNMP). SNMP is an application layer protocol used by network management tools to exchange management information between network devices. Cisco NAC Appliance and Cisco WLCs support the following SNMP versions in a Wireless OOB environment:

CAM-to-OOB WLC SNMP Read
CAM-to-OOB WLC SNMP Write
OOB WLC-to-CAM SNMP Traps

SNMP V1

SNMP V2c (V2 with community string)

SNMP V1

SNMP V2c

SNMP V3

SNMP V2c


You first need to configure the WLC to send and receive SNMP traffic to/from the Clean Access Manager, then configure matching settings on the Clean Access Manager to send and receive traffic to/from the WLC. This will enable the Clean Access Manager to get VLAN information from the WLC and coordinate with the WLC when wireless users log out (or are "kicked out") of the network and removed from the Online Users List.

Summary Steps to Configure Wireless Out-of-Band

To enable Wireless OOB in you access network, you need to perform the following tasks:

1. Configure your Wireless LAN Controller:

a. Enable SNMP read and write settings on the WLC.

b. Enable SNMP trap transmission on the WLC using SNMP v2c (the SNMP v2c protocol is the only version of SNMP traps the CAM and WLCs have in common).

c. Configure SSIDs/dynamic interfaces on the WLC with both an Authentication (Quarantine) VLAN and a standard Access VLAN.

2. Ensure SNMP settings on the CAM match those assigned on the WLC using the guidelines in Configure SNMP Receiver.

3. Create a new device profile on the CAM for the WLC using the guidelines in Add New Wireless LAN Controller.


Note Unlike switch device profiles on the CAM, administrators do not configure or assign any Port Profiles for WLCs. VLAN assignments for Authentication (Quarantine) and Access VLANs originate form the WLC based on SNMP trap messages sent from the CAM following client posture assessment and remediation.

4. Add the new WLC device profile to the Device List using the guidelines in Add and Manage Wireless LAN Controllers.

5. Configure the CAS in your Cisco NAC Appliance network to support Wireless OOB network functions using the appropriate sections of the "Configuring the CAS Managed Network" chapter in the Cisco NAC Appliance - Clean Access Server Configuration Guide, Release 4.7(5):

Install the CAS as a Virtual Gateway according to the guidelines in the "Add New Server" section.

Ensure that the Cisco NAC Appliance system appropriately handles client traffic from the WLC's Authentication (Quarantine) VLAN by using the "Configuring Managed Subnets or Static Routes" section.

Since the CAS acts as a bridge in Virtual Gateway mode, be sure the CAS is configured to map the WLC's Access VLAN to the Cisco NAC Appliance Access VLAN (both on the Trusted VLAN) using the "Configure VLAN Mapping" section.

Wireless Out-of-Band Virtual Gateway Deployment

Figure 4-1 illustrates a typical Wireless OOB Virtual Gateway deployment. The WLC assigns two VLANs, AUthentication (Quarantine) VLAN 110 and Access VLAN 10, to one or more SSIDs/dynamic interfaces to support wireless client access. The WLC and the Layer 2 access switch have a VLAN trunk assignment for both VLANs so that client traffic automatically reaches the Layer 2 switch regardless of whether the wireless client machine has authenticated with Cisco NAC Appliance or not. The Layer 2 switch ensures that all unauthenticated traffic gets directed to the Clean Access Server via VLAN 110 and that authenticated clients remain Out-of-Band, thus bypasses the CAS and proceeding directly to the internal network via Access VLAN 10.

Figure 4-1 Wireless Out-of-Band Layer 2 VGW Mode

Login and Authentication Flow in Wireless OOB Virtual Gateway Mode

1. The unauthenticated wireless user connects to a Wireless LAN Controller through an associated wireless access point.

2. The WLC sends an association trap informing the CAM that a wireless user is logging in with Cisco NAC Appliance network access credentials

3. When the wireless client first logs into the Wireless OOB network, the user profile is assigned to Authentication (Quarantine) VLAN 110.

4. The CAS assigns the client machine an IP address from the access VLAN 10 and the WLC authenticates the client.


Note If Single-Sign On (SSO) is configured for the Wireless OOB network, the WLC also sends the appropriate RADIUS accounting packets to the CAS.

Cisco WLCs do not support IPSec communication with the Cisco NAC Appliance network, so you cannot provide RADIUS SSO capability to users in your FIPS 140-2 compliant environment.

5. Cisco NAC Appliance performs posture assessment and remediation on the client machine and, if the client machine meets security requirements, authenticates the client and sends an SNMP SET command to the WLC granting access to the internal network.

6. The WLC switches the client IP address from the Authentication (Quarantine) VLAN 110 to the Access VLAN 10 and (now that the client machine has authenticated with Cisco NAC Appliance) traffic between the wireless client machine and the internal network moves Out-of-Band, bypassing the CAS.

When the user logs out of the wireless OOB network, the WLC sends another SNMP update to the CAM to ensure the CAM removes the user profile from the wireless Online Users List. Likewise, if the Cisco NAC Appliance administrator is forced to "kick" a user out of the network, the CAM sends an SNMP trap to the WLC and the WLC, in return, automatically moves the user back to the Authentication (Quarantine) VLAN, thus directing the now unauthenticated client traffic to the CAS.

Configure Your Network for Wireless Out-of-Band

The CAM communicates with associated WLCs using SNMP and manages Wireless OOB Virtual Gateway CASs through the admin network. The trusted interface of the CAS connects to the admin/management network, and the untrusted interface of the CAS connects to the managed client network.

When a wireless client connects to a WLC, the WLC automatically assigns the client to an Authentication (Quarantine) VLAN and the traffic to/from the client goes through the CAS. After the client is authenticated and certified through the Clean Access Server, the WLC receives an SNMP message from the CAM allowing the client access to the network via the Access VLAN. Once on the access VLAN, traffic to and from certified clients moves Out-of-Band, bypassing the Clean Access Server.

The next sections describe the configuration steps needed to set up your Wireless OOB deployment:

Configure Your Wireless LAN Controllers

Configure Wireless LAN Controller Connection on the CAM


Note You can only deploy CASs supporting wireless client machine authentication in Virtual Gateway mode.

Configure Your Wireless LAN Controllers

This section describes the steps needed to set up Wireless LAN Controllers (WLCs) to be used with Cisco NAC Appliance for Wireless Out-of-Band.

Wireless LAN Controllers Configuration Notes

Example Wireless LAN Controller Configuration Steps

Wireless OOB Network Setup/Configuration Worksheet

Wireless LAN Controllers Configuration Notes

The following considerations should be taken into account when configuring Wireless LAN Controllers for OOB:

Cisco NAC Appliance only supports Wireless OOB deployments with Cisco Wireless LAN Controllers.

WLCs must be configured to interact with the CAM using SNMP read, write, and trap functions.

Each service set identifier (SSID)/dynamic interface on the WLC must have both an Authentication (Quarantine) VLAN and Access VLAN configured.

When SSID is setup to perform Wireless SSO and there is a overlapping of IP subnets over multiple SSIDs, even after roaming from one SSID to another, the user is still listed under Online Users in the CAM. To avoid this, create separate IP ranges for each SSID.

Ensure that any access/aggregation switches in the network between the WLCs and the Clean Access Server have the same Authentication (Quarantine) and Access VLANs trunked.

Authentication and Access VLANs are defined on the WLC and changes between the two are transmitted to the CAM using SNMP traps—administrators do not assign VLANs from the CAM via user role assignments or otherwise.

When a wireless user logs off, the WLC also sends SNMP information to the CAM to ensure the user ID is removed from the Online Users List. Likewise, if the administrator must kick any users out of the Online Users List, the CAM informs the WLC via SNMP and the WLC automatically assigns the wireless client to the Authentication (Quarantine) VLAN.

If Single Sign-On (SSO) is required for wireless users, the WLC must also be configured to transmit RADIUS accounting packets to the CAS. Cisco WLCs do not support IPSec communication with the Cisco NAC Appliance network, so you cannot provide RADIUS SSO capability to users in your FIPS 140-2 compliant environment.


Note The VPN Auto Logout feature does not work in a Wireless OOB deployment. If VPN Auto Logout signs a user out of the system, the CAM will not learn of the disconnection from the WLC.

If your wireless access network provides services for Wireless IP Phones, ensure you configure a separate SSID for such devices so that they do not encounter the Cisco NAC Appliance authentication process.

Example Wireless LAN Controller Configuration Steps

This section provides a configuration example for a Cisco 4400 series Wireless LAN Controller.

Create the Dynamic Interface on the Wireless LAN Controller

Create the WLAN on the Wireless LAN Controller and Enable Cisco NAC Appliance Integration

Configure SNMP on the Wireless LAN Controller

Specify the CAM as the SNMP Trap Receiver

Create the Dynamic Interface on the Wireless LAN Controller

To create and specify settings for a new Dynamic Interface on the Wireless LAN Controller:


Step 1 In the WLC graphical user interface, click Controller > Interfaces to open the Interfaces page.

Step 2 Click New and enter an Interface Name and VLAN ID in the Interfaces > New page that appears.

Step 3 Click Apply to commit your changes. The Interfaces > Edit page appears (Figure 4-2).

Figure 4-2 WLC 4400 Interfaces > Edit Page

Step 4 Configure the following parameters:

Guest LAN

Enable the Quarantine option and specify a quarantine Quarantine VLAN ID.


Note Check the Quarantine check box if you want to configure this VLAN as unhealthy or you want to configure network access control (NAC) out-of-band integration. Doing so causes the data traffic of any client that is assigned to this VLAN to pass through the controller.

Physical port assignment

VLAN identifier

Fixed IP address, IP netmask, and default gateway

Primary and secondary DHCP servers

Access control list (ACL) name, if required


Note To ensure proper operation, you must set the Port Number and Primary DHCP Server parameters.

Step 5 Click Save Configuration to save your changes.

Step 6 Repeat this procedure for each dynamic interface that you want to create or edit.

For more information, refer to the Cisco Wireless LAN Controller Configuration Guide, Release 5.1.


Create the WLAN on the Wireless LAN Controller and Enable Cisco NAC Appliance Integration

To create a new WLAN on the Wireless LAN Controller and enable integration with Cisco NAC Appliance:


Step 1 In the WLC graphical user interface, click WLANs > New. The WLANs > New page appears.

Step 2 Choose WLAN from the Type dropdown menu.

Step 3 Enter up to 32 alphanumeric characters for the profile name to be assigned to this WLAN in the Profile Name field. The profile name must be unique.

Step 4 Enter up to 32 alphanumeric characters for the SSID to be assigned to this WLAN in the WLAN SSID field.

Step 5 Click Apply to commit your changes. The WLANs > Edit page appears (Figure 4-3).

Figure 4-3 WLC 4400 WLANs > Edit Page

Step 6 On the General tab, check the Status checkbox to enable this WLAN.


Caution Leave this option unchecked (disabled) until you have finished making configuration changes to the WLAN.

Step 7 On the Advanced tab, check the State checkbox under the "NAC" heading to enable WLC integration with Cisco NAC Appliance.

Step 8 Specify a Quarantine VLAN ID for wireless user sessions when authenticating with Cisco NAC Appliance.

Step 9 Click Apply to commit your changes.

Step 10 Click Save Configuration to save your changes.

For more information, refer to the Cisco Wireless LAN Controller Configuration Guide, Release 5.1.


Configure SNMP on the Wireless LAN Controller

To ensure the Wireless LAN Controller is able to receive and process SNMP transmissions from the CAM regarding OOB client machine status in the Cisco NAC Appliance system, you must enable and configure SNMP behavior on the WLC.

To create a new SNMP community and enable SNMP on the WLC:


Step 1 Click Management and then Communities under SNMP. The SNMP v1 / v2c Community page appears.

Step 2 Click New to create a new community. The SNMP v1 / v2c Community > New page appears (Figure 4-4).

Figure 4-4 SNMP v1 / v2c Community > New Page

Step 3 In the Community Name field, enter a unique name containing up to 16 alphanumeric characters. (Do not enter "public" or "private.")

Step 4 Enter the IP Address of the CAM from which this device accepts SNMP packets with the associated community and the respective IP Mask.

Step 5 Choose Read/Write from the Access Mode dropdown menu to specify the access level for this community.

Step 6 Choose Enable from the Status dropdown menu to activate this community.

Step 7 Click Apply to commit your changes.

Step 8 Click Save Configuration to save your settings.

Step 9 Repeat this procedure if a "public" or "private" community still appears on the SNMP v1 / v2c Community page.

For more information, refer to the Cisco Wireless LAN Controller Configuration Guide, Release 5.1.


Specify the CAM as the SNMP Trap Receiver

Once you enable and configure SNMP on the Wireless LAN Controller, you must also ensure the WLC knows which CAM is receiving SNMP trap messages.

To specify the host name and IP address of the SNMP trap receiver CAM:


Step 1 Click Management and then Trap Receivers under SNMP. The SNMP Trap Receivers > New page appears (Figure 4-5).

Figure 4-5 SNMP Trap Receivers > New Page

Step 2 Specify the host name of the CAM to receive SNMP traps from the WLC in the Trap Receiver Name field.

Step 3 Enter the CAM's IP address in the IP Address field.

Step 4 Choose Enable from the Status dropdown menu.

Step 5 Click Apply to commit your changes.

Step 6 Click Save Configuration to save your settings.


Wireless OOB Network Setup/Configuration Worksheet

Table 4-3 summarizes information needed to configure WLCs and the Clean Access Manager.

Table 4-3 Configuration Worksheet  

Configuration Settings
Value
Wireless LAN Controller Configuration

WLC IP Address/Netmask:

 

New dynamic interface

 

SSID Access VLAN:

 

SSID Authentication (Quarantine) VLAN:

 

SNMP version used

 

SNMP (V1/V2c) read community name:

 

SNMP (V1/V2c) write community name:

 

SNMP (V3) auth method/username/password:

 

SNMP Trap V2c community string (to send traps to CAM):

 
CAM/CAS Configuration

CAM host name

 

CAM IP address:

 

CAS Trusted IP address:

 

CAS Untrusted IP address:

 

CAM SNMP Trap Receiver

 

Community name for SNMP Trap V1 devices:

 

Community name for SNMP Trap V2c devices:

 

Auth method/username/password for SNMP Trap V3 WLCs:

 

Configure Wireless LAN Controller Connection on the CAM

This section describes the web admin console configuration steps to implement Wireless OOB. In general, you first configure Group and Wireless LAN Controller profiles, and the CAM's SNMP Receiver settings under OOB Management > Profiles. After the WLC profile is configured, add the new WLC you want to communicate with to the Clean Access Manager's domain under OOB Management > Devices, and ensure the new profile appears in the Devices list.

The configuration sequence is as follows:

1. Plan your settings and configure the switches to be managed, as described in previous section, Configure Your Wireless LAN Controllers

2. Add a Wireless Out-of-Band Clean Access Server and Configure Environment

3. Configure Group Profiles

4. Configure Wireless LAN Controller Profiles

5. Configure SNMP Receiver

6. Add and Manage Wireless LAN Controllers

Add a Wireless Out-of-Band Clean Access Server and Configure Environment

Almost all the CAM/CAS configuration for Wireless Out-of-Band deployment is done directly in the OOB Management module of the CAM web console. If your Wireless LAN Controller installation features great enough throughput/bandwidth, you can (and may need to) configure more than one Clean Access Server to handle all of the authentication traffic between wireless client machines and the Cisco NAC Appliance system.

To add a Wireless OOB Clean Access Server to the CAM:


Step 1 Choose the Out-of-Band Virtual Gateway option from the Server Type dropdown menu (Figure 4-6).

Figure 4-6 Add New OOB Server

The Clean Access Server itself must be either in-band or out-of-band. The Clean Access Manager can control both in-band and out-of-band CASs in its domain.


Note You can only deploy CASs supporting wireless client machine authentication in Virtual Gateway mode.

Step 2 Enter the IP address of the Clean Access Server's eth0 (trusted) interface in the Server IP Address field.

Step 3 (Optional) Enter the Clean Access Server location/description/purpose in the Server Location field.

Step 4 Click Add Clean Access Server.


Configure Group Profiles

When you first add a WLC to the Clean Access Manager's domain (under OOB Management > Devices), a Group profile must be applied to add the new WLC. There is a predefined Group profile called default, shown in Figure 4-7. All WLCs are automatically put in the default group when you add them. You can leave this default Group profile setting, or you can create additional Group profiles as needed. If you are adding and managing a large number of WLCs, creating multiple Group profiles allows you to filter which sets of devices to display from the list of WLCs (under OOB Management > Devices > Devices > List).

Figure 4-7 Group Profiles List

Add Group Profile


Step 1 Go to OOB Management > Profiles > Group > New (Figure 4-8).

Figure 4-8 New Group

Step 2 Enter a single word for the Group Name. You can use digits and underscores, but no spaces.

Step 3 Enter an optional Description.

Step 4 Click Add. The new Group profile appears under OOB Management > Profiles > Group > List.


Edit Group Profile


Step 1 To edit the profile later, after actual WLCs are added, go to OOB Management > Profiles > Group > List and click the Edit button for the new Group profile.

Step 2 The Edit page appears (Figure 4-9).

Figure 4-9 Edit Group

Step 3 You can toggle the WLCs that belong in the Group profile by selecting the IP address of the WLC from the Member Devices or Available Devices columns and clicking the Join or Remove buttons as applicable.

Step 4 Click the Update button when done to save your changes.


Note To delete a group profile, you must first remove the joined switches and/or WLCs from the profile.

Configure Wireless LAN Controller Profiles

A WLC profile must first be created under OOB Management > Profiles > Device > New, then applied when a new WLC is added. A WLC profile classifies WLCs of the same model and SNMP settings, as shown in Figure 4-10. The WLC profile configures how the CAM learns client Authentication/Access VLAN assignments from the WLC and when to remove Wireless OOB clients from the Online Users List for a WLC of that type.

Figure 4-10 Device Profiles List

The Device profiles list under OOB Management > Profiles > Device > List provides three buttons:

Devices—Clicking this button brings up the list of added devices under OOB Management > Devices > Devices > List (see Figure 4-14).

Edit—Clicking this button brings up the Edit Device profile form (see Figure 4-12).

Delete—Clicking this icon deletes the Device profile (a confirmation dialog appears first).

Add Wireless LAN Controller Profile

Use the following steps to add a Wireless LAN Controller profile.


Step 1 Go to OOB Management > Profiles > Device > New (Figure 4-11).

Figure 4-11 New Wireless LAN Controller Profile

Step 2 Enter a single word for the Profile Name. You can use digits and underscores but no spaces.


Note It is a good idea to enter a WLC name that identifies the model and SNMP read and write versions, for example "WLC4400v2v3."

Step 3 Choose the Device Model for the profile from the dropdown menu.

Step 4 Enter the SNMP Port configured on the WLC to send/receive traps. The default port is 161.

Step 5 Enter an optional Description.

Step 6 Configure SNMP Read Settings to match those on the WLC.

Choose the SNMP Version: SNMP V1 or SNMP V2C.

Type the Community String configured for the WLC.

Step 7 Configure SNMP Write Settings to match those on the WLC.

Choose the SNMP Version: SNMP V1, SNMP V2C, or SNMP V3.

Type the Community String for SNMP V1 or SNMP V2C configured for the WLC.

Step 8 If SNMP v3 is used for SNMP write settings on the WLC, configure the following settings to match those on the WLC:

Choose a Security Method from the dropdown menu: NoAuthNoPriv, AuthNoPriv(MD5), AuthNoPriv(SHA), AuthPriv(MD5+DES-CBC), or AuthPriv(SHA+DES-CBC).

Type the User Name.

Type the User Auth.

Type the User Priv.

Step 9 Click Add to add the Wireless LAN Controller profile to OOB Management > Profiles > Device > List (Figure 4-14).

Figure 4-12 illustrates a WLC profile defining a Cisco 440 Wireless LAN Controller with the same SNMP settings: SNMP V2c with read community string "wlc4400_read" and write community string "wlc4400_write."

Figure 4-12 Example Wireless LAN Controller Profile


Configure SNMP Receiver

The SNMP Receiver form configures how the SNMP Receiver running on the Clean Access Manager receives and responds to SNMP trap notifications from WLCs when user events occur (such as when a user first logs on to or logs off of the network). The SNMP Receiver configuration on the CAM must match the WLC configuration in order for the WLC to send SNMP traps to the CAM.

SNMP Trap

This page configures settings for the SNMP traps the CAM receives from switches and WLCs. The Clean Access Manager SNMP Receiver can simultaneously support different versions of SNMP (V1, V2c, V3) when controlling groups of switches and/or WLCs in which individual devices may be using different versions of SNMP.


Step 1 Go to OOB Management > Profiles > SNMP Receiver > SNMP Trap (Figure 4-13).

Figure 4-13 CAM SNMP Receiver

Step 2 Use the default Trap Port on Clean Access Manager (162) or enter a new port number here.

Step 3 For SNMP V1 Settings, type the Community String used on switches using SNMP V1.

Step 4 For SNMP V2c Settings, type the Community String used on switches using SNMP V2c.

Step 5 For SNMP V3 Settings, configure the following fields used on switches using SNMP V3:

Choose the Security Method from the dropdown menu: NoAuthNoPriv, AuthNoPriv(MD5), AuthNoPriv(SHA), AuthPriv(MD5+DES-CBC), or AuthPriv(SHA+DES-CBC)

Type the User Name.

Type the User Auth.

Type the User Priv

Step 6 Click Update to save settings.


Add and Manage Wireless LAN Controllers

The pages under the OOB Management > Devices > Devices tab are used to discover and add new switches and WLCs within an IP range, add new switches or WLCs by exact IP address, and manage the list of associated devices. There are two methods to add new managed WLCs:

Add New Wireless LAN Controller

Search New Wireless LAN Controllers

Figure 4-14 List of Devices

The list of devices under OOB Management > Devices > Devices > List displays all switches added from the New or Search forms. Wireless LAN Controller entries in the list include the WLC's IP address, MAC address, Description, and WLC Profile. You can sort the entries on the list by Device Group or Device Profile dropdowns, or you can simply type a Device IP and hit Enter to search for a switch by its address. Additionally the List provides one control and two buttons:

Config—Clicking the Config button brings up the Config Tab for the WLC.

Delete—Clicking the Delete button deletes the WLC from the list (a confirmation dialog appears before the WLC entry is removed).


Note The Port Profile dropdown is only used for adding switches to the Devices list and does not pertain to WLCs.

Profile links do not apply to WLCs and are "grayed out" in the Devices list for WLC entries.

Add New Wireless LAN Controller

The New page allows you to add WLCs when exact IP addresses are already known.


Step 1 Go to OOB Management > Devices > Devices > New (Figure 4-15).

Figure 4-15 Add New Wireless LAN Controller

Step 2 Choose the Device Profile from the dropdown menu to apply to the WLC to be added.

Step 3 Choose the Device Group for the WLC from the dropdown menu.

Step 4 Type the IP Addresses of the WLC(s) you want to add. Separate each IP address by line.

Step 5 Enter an optional Description of the new switch.

Step 6 Click the Add button to add the WLC(s).

Step 7 Click the Reset button to reset the form.


Search New Wireless LAN Controllers

The Search page allows you to discover and add unmanaged switches within an IP range.


Step 1 Go to OOB Management > Devices > Devices > Search (Figure 4-16).

Figure 4-16 Search Devices

Step 2 Select a Device Profile from the dropdown list. The read community string of the selected WLC profile is used to find WLCs with matching read settings.

Step 3 Type an IP Range in the text box. (The maximum range for a search is 256 addresses.)

Step 4 By default, the Don't list devices already in the database checkbox is already checked. If you uncheck this box, the resulting search will include devices you have already added.

Step 5 Choose a Device Group from the dropdown to apply to the WLCs found in the search.

Step 6 Click the checkbox to the left of each WLC you want to connect with the CAM. Alternatively, click the checkbox at the top of the column to add all WLCs found from the search.


Note While all WLCs matching the read community string of the WLC profile used for the search are listed, only those WLCs matching the read SNMP version and community string can be added using the Commit button. The CAM cannot communicate with a WLC unless its write SNMP settings match those configured for its WLC profile.

Step 7 Click the Commit button to add the new devices. These devices are listed under OOB Management > Devices > Devices > List.


Discovered Wireless Clients

Figure 4-17 shows the OOB Management > Devices > Discovered Clients > Wireless Clients page. The Wireless Clients page lists all clients discovered by the Clean Access Manager via SNMP traps between the CAM and the WLC. The page records the activities of out-of-band clients (regardless of VLAN), based on the SNMP trap information that the Clean Access Manager receives.

When a client connects to a WLC and is assigned to the Authentication (Quarantine) VLAN, a trap is sent and the Clean Access Manager creates an entry on the Wireless Clients page. The Clean Access Manager adds a client's MAC address, IP address, associated WLC, Access Point MAC address, and Authentication (Quarantine) and Access VLAN assignments to the Wireless Clients list. Thereafter, the CAM updates the entry as it receives new SNMP trap information for the client.

Removing an entry from the Wireless Clients list clears this status information for the Wireless OOB client from the CAM.

Figure 4-17 Wireless Clients

Elements of the page are as follows:

Show clients connected to WLC with IP—Leave the default of ALL WLCs displayed, or choose a specific WLC from the dropdown menu. The dropdown menu displays all managed WLCs configured on the CAM.

Show client with MAC—Type a specific MAC address and press Enter to display a particular client.

Clients/Page—Leave the default of 25 entries displayed per page, or choose from the dropdown menu to displays 50, 100, 200, or ALL entries on the page.

Delete All Clients—This button removes all clients on the list.

Delete Selected—This button only removes the clients selected in the check column to the far right of the page.

Note that you can click any of the following column headings to sort results by that column:

MAC—MAC address of discovered wireless client

IP—IP address of the wireless client

WLC—IP address of the originating Wireless LAN Controller. Clicking the WLC IP address brings up the OOB Management > Devices > WLC [IP address] > Config > Basic page for the WLC. (For more information, see Config Tab.)

SSID—The service set identifier to which the wireless client has been associated for network access.

AP MAC—The MAC address of the WLC Access Point through which the client is accessing the network

Auth VLAN—Authentication (Quarantine) VLAN
A value of "N/A" in this column indicates that the VLAN ID for this MAC address is unavailable from the WLC.

Access VLAN—Access VLAN of the client
A value of "N/A" in this column indicates the Access VLAN ID is unavailable for the client. For example, if the user is switched to the Authentication VLAN but has never successfully logged into Cisco NAC Appliance (due to wrong user credentials), this machine will never have been assigned to the Access VLAN.

Last Update—The last time the CAM updated the information of the entry.

See Wireless Out-of-Band Users for additional details on monitoring out-of-band users.

Config Tab

The Config tab allows you to modify Basic and Group profile settings for a particular Wireless LAN Controller:

Basic

Group

Basic

The Basic tab (Figure 4-18) shows the following values configured for the WLC.

Figure 4-18 Config > Basic

The first values come from the initial configuration done on the WLC itself:

IP Address

MAC Address

Location

Contact

System Info (translated from the MIB for the WLC)

Device Profile—Shows the Device Profile you are using for this WLC configured under OOB Management > Profiles > Device. The WLC Device Profile sets the model type, the SNMP port on which to send SNMP traps, SNMP version for read and write and corresponding community strings, or authentication parameters (SNMP V3 Write).

Description—Optional description of the WLC. To change this field, type a new description and click Update.

Group

This page displays all the Group Profiles configured in the Clean Access Manager, and the Group Profiles to which the WLC currently belongs. You can add the WLC to other Groups, or you can remove the WLC from a Group Joined. To change the Group membership for all switches, go to OOB Management > Profiles > Group (see Configure Group Profiles).

Figure 4-19 Config > Group

View Wireless Out-of-Band Online Users

When out-of-band is enabled, the Monitoring > View Online Users page displays links for both In-Band and Out-of-Band users and display settings (Figure 4-20). See Out-of-Band Users for details.

Figure 4-20 View Out-of-Band Online Users

Wireless Out-of-Band Users

Wireless OOB User Sessions

The following events trigger Wireless OOB users' disconnection from the Cisco NAC Appliance system:

SNMP trap messages from the WLC

Certified Timer expiration

Session Timer expiration

Manual removal from CAM

Following log-off, users must undergo authentication again before they are allowed back into the internal network. For additional details, see also Interpreting Event Logs and Manage Certified Devices.

Wireless and Wired OOB User List Summary

Table 3-3 describes the lists used to track out-of-band users.