Before you can use
Firepower Chassis Manager
or the FXOS CLI
to configure and manage your system, you must perform some initial
configuration tasks using the
FXOS CLI
accessed through the console port. The first time that you access the
Firepower 9300 chassis
using the
FXOS CLI,
you will encounter a setup wizard that you can use to configure the system.
You can choose to
either restore the system configuration from an existing backup file, or
manually set up the system by going through the Setup wizard. If you choose to
restore the system, the backup file must be reachable from the management
network.
You must specify
only one IPv4 address, gateway, and subnet mask, or only one IPv6 address,
gateway, and network prefix for the single management port on the
Firepower 9300 chassis.
You can configure either an IPv4 or an IPv6 address for the management port IP
address.
The following
example sets up a configuration using IPv4 management addresses:
Enter the setup mode; setup newly or restore from backup. (setup/restore) ? setup
You have chosen to setup a new Fabric interconnect. Continue? (y/n): y
Enforce strong password? (y/n) [y]: n
Enter the password for "admin": adminpassword%958
Confirm the password for "admin": adminpassword%958
Enter the system name: foo
Physical Switch Mgmt0 IP address : 192.168.10.10
Physical Switch Mgmt0 IPv4 netmask: 255.255.255.0
IPv4 address of the default gateway: 192.168.10.1
Do you want to configure IP block for ssh access? (yes/no) [y]: y
SSH IPv4 block netmask: 0.0.0.0
Do you want to configure IP block for https access? (yes/no) [y]: y
HTTPS IP block address: 0.0.0.0
HTTPS IPv4 block netmask: 0.0.0.0
Configure the DNS Server IP address (yes/no) [n]:y
DNS IP address: 20.10.20.10
Configure the default domain name? (yes/no) [n]: y
Default domain name: domainname.com
Following configurations will be applied:
Switch Fabric=A
System Name=foo
Enforce Strong Password=no
Physical Switch Mgmt0 IP Address=192.168.10.10
Physical Switch Mgmt0 IP Netmask=255.255.255.0
Default Gateway=192.168.10.1
IPv6 value=0
SSH Access Configured=yes
SSH IP Address=0.0.0.0
SSH IP Netmask=0.0.0.0
HTTPS Access Configured=yes
HTTPS IP Address=0.0.0.0
HTTPS IP Netmask=0.0.0.0
DNS Server=20.10.20.10
Domain Name=domainname.com
Apply and save the configuration (select 'no' if you want to re-enter)? (yes/no): yes
The following
example sets up a configuration using IPv6 management addresses:
Enter the setup mode; setup newly or restore from backup. (setup/restore) ? setup
You have chosen to setup a new Fabric interconnect. Continue? (y/n): y
Enforce strong password? (y/n) [y]: n
Enter the password for "admin": adminpassword%652
Confirm the password for "admin": adminpassword%652
Enter the system name: foo
Physical Switch Mgmt0 IP address : 2001::107
Physical Switch Mgmt0 IPv6 prefix: 64
IPv6 address of the default gateway: 2001::1
Do you want to configure IP block for ssh access? (yes/no) [y]: y
SSH IPv6 block netmask: 0.0.0.0
Do you want to configure IP block for https access? (yes/no) [y]: y
HTTPS IP block address: 0.0.0.0
HTTPS IPv6 block netmask: 0.0.0.0
Configure the DNS Server IPv6 address? (yes/no) [n]: y
DNS IP address: 2001::101
Configure the DNS Server IP address (yes/no) [n]:
Configure the default domain name? (yes/no) [n]: y
Default domain name: domainname.com
Following configurations will be applied:
Switch Fabric=A
System Name=foo
Enforced Strong Password=no
Physical Switch Mgmt0 IPv6 Address=2001::107
Physical Switch Mgmt0 IPv6 Prefix=64
Default Gateway=2001::1
Ipv6 value=1
SSH Access Configured=yes
SSH IP Address=0.0.0.0
SSH IP Netmask=0.0.0.0
HTTPS Access Configured=yes
HTTPS IP Address=0.0.0.0
HTTPS IP Netmask=0.0.0.0
DNS Server=2001::101
Domain Name=domainname.com
Apply and save the configuration (select 'no' if you want to re-enter)? (yes/no): yes