Cisco ASA 5580 Hardware Installation Guide
About This Guide
Downloads: This chapterpdf (PDF - 102.0KB) The complete bookPDF (PDF - 4.25MB) | Feedback

About This Guide

Table Of Contents

About This Guide

Document Objectives

Audience

Installation Warnings

Where to Find Safety and Warning Information

Obtaining Documentation and Submitting a Service Request


About This Guide


This preface includes the following sections:

Document Objectives

Audience

Installation Warnings

Obtaining Documentation and Submitting a Service Request

Document Objectives

This guide describes how to perform maintenance procedures on the Cisco ASA 5580.

Audience

This guide is for network administrators who install firewalls.

Installation Warnings

Be sure to read the Regulatory Compliance and Safety Information for the Cisco ASA 5580 document that accompanied this device before installing the chassis. This document contains important safety information. This section includes the following warnings:

AC Power Disconnection Warning

Jewelry Removal Warning

Wrist Strap Warning

Work During Lightning Activity Warning

Installation Instructions Warning

Chassis Warning for Rack-Mounting and Servicing

Short-Circuit Protection Warning

SELV Circuit Warning

Ground Conductor Warning

Blank Faceplates and Cover Panels Warning

Product Disposal Warning

Short-Circuit Protection Warning

Compliance with Local and National Electrical Codes Warning

TN Power Warning

Multiple Power Cord

Circuit Breaker (15A) Warning

Grounded Equipment Warning

Safety Cover Requirement

Faceplates and Cover Panel Requirement

AC Power Disconnection Warning


Warning Before working on a chassis or working near power supplies, unplug the power cord on AC units. Statement 246

Jewelry Removal Warning


Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals. Statement 43

Wrist Strap Warning


Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94

Work During Lightning Activity Warning


Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001

Installation Instructions Warning


Warning Read the installation instructions before connecting the system to the power source. Statement 1004

Chassis Warning for Rack-Mounting and Servicing


Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: This unit should be mounted at the bottom of the rack if it is the only unit in the rack.When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack.If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. Statement 1006

Short-Circuit Protection Warning


Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations. Statement 1045

SELV Circuit Warning


Warning To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables. Statement 1021

Ground Conductor Warning


Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Blank Faceplates and Cover Panels Warning


Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029

Product Disposal Warning


Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040

Short-Circuit Protection Warning


Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations. Statement 1045

Compliance with Local and National Electrical Codes Warning


Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074

TN Power Warning


Warning The device is designed to work with TN power systems. Statement 19

Multiple Power Cord


Warning This unit has more than one power cord. To reduce the risk of electric shock when servicing a unit, disconnect the power cord of the power strip that the unit is plugged into. Statement 137

Circuit Breaker (15A) Warning


Warning This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 10A international) is used on the phase conductors (all current-carrying conductors). Statement 13

Grounded Equipment Warning


Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use. Statement 39

Safety Cover Requirement


Warning The safety cover is an integral part of the product. Do not operate the unit without the safety cover installed. Operating the unit without the cover in place will invalidate the safety approvals and pose a risk of fire and electrical hazards. Statement 117

Faceplates and Cover Panel Requirement


Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 142

Where to Find Safety and Warning Information

For safety and warning information, see the Regulatory Compliance and Safety Information for the Cisco ASA 5580 document that accompanied the product. This document describes the international agency compliance and safety information for the adaptive security appliance. It also includes translations of the safety warnings.

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What's New in Cisco Product Documentation as an RSS feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service. Cisco currently supports RSS Version 2.0.