Cisco Security Appliance Command Reference, Version 7.2
show running-config ldap through show running-config webvpn auto-signon Commands
Downloads: This chapterpdf (PDF - 649.0KB) The complete bookPDF (PDF - 20.65MB) | Feedback

show running-config ldap through show running-config wccp Commands

Table Of Contents

show running-config ldap through show running-config wccp Commands

show running-config ldap

show running-config logging

show running-config mac-address

show running-config mac-address-table

show running-config mac-learn

show running-config mac-list

show running-config management-access

show running-config monitor-interface

show running-config mroute

show running-config mtu

show running-config multicast-routing

show running-config name

show running-config nameif

show running-config names

show running-config nat

show running-config nat-control

show running-config ntp

show running-config object-group

show running-config passwd

show running-config pim

show running-config policy-map

show running-config pop3s

show running-config port-forward

show running-config prefix-list

show running-config priority-queue

show running-config privilege

show running-config regex

show running-config route

show running-config route-map

show running-config router

show running-config same-security-traffic

show running-config service

show running-config service-policy

show running-config sla monitor

show running-config snmp-map

show running-config snmp-server

show running-config ssh

show running-config ssl

show running-config static

show running-config sunrpc-server

show running-config sysopt

show running-config tcp-map

show running-config telnet

show running-config terminal

show running-config tftp-server

show running-config timeout

show running-config track

show running-config tunnel-group

show running-config url-block

show running-config url-cache

show running-configuration url-list

show running-config url-server

show running-config username

show running-config virtual

show running-config vpn load-balancing

show running-config webvpn

show running-config webvpn auto-signon

show running-config zonelabs-integrity

show running-config smtps

show running-config vpdn

show running-configuration vpn-sessiondb

show running-config wccp


show running-config ldap through show running-config wccp Commands


show running-config ldap

To display the LDAP attribute name and value mappings in running LDAP attribute maps, use the show running-config ldap command in privileged EXEC mode.

show running-config [all] ldap attribute-map name

Syntax Description

Syntax DescriptionSyntax Description

all

Displays all LDAP attribute maps.

name

Specifies an individual LDAP attribute map for display.


Defaults

By default, all attribute maps, mapped names, and mapped values display.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.1(1)

This command was introduced.


Usage Guidelines

Use this command to display the LDAP attribute name and value mappings contained in attribute maps running on your security appliance. You can display all the attribute maps using the all option, or you can display a single attribute map by specifying the map name. If you enter neither the all option nor an LDAP attribute map name, all attribute maps, mapped names, and mapped values display.

Examples

The following example, entered in privileged EXEC mode, displays the attribute name and value mappings for a specific running attribute map, "myldapmap":

hostname# show running-config ldap attribute-map myldapmap
map-name Hours cVPN3000-Access-Hours
map-value Hours workDay Daytime

The following command displays all attribute name and value mappings within all running attribute maps:

hostname# show running-config all ldap attribute-map

Related Commands

Command
Description

ldap attribute-map (global config mode)

Creates and names an LDAP attribute map for mapping user-defined attribute names to Cisco LDAP attribute names.

ldap-attribute-map (aaa-server host mode)

Binds an LDAP attribute map to an LDAP server.

map-name

Maps a user-defined LDAP attribute name with a Cisco LDAP attribute name.

map-value

Maps a user-defined attribute value to a Cisco attribute.

clear configure ldap attribute-map

Removes all LDAP attribute maps.


show running-config logging

To display all currently running logging configuration, use the show runnig-config logging command in privileged EXEC mode.

show running-config [all] logging [level | disabled]

Syntax Description

all

(Optional) Displays the logging configuration, including commands that you have not changed from the default.

disabled

(Optional) Displays only the disabled system log message configuration.

level

(Optional) Displays only the configuration for system log messages with a non-default severity level.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1) (1)

This command was changed from the show logging command.


Examples

The following is an example of the show running-config logging disabled command:

hostname# show running-config logging disabled

no logging message 720067

Related Commands

Command
Description

logging message

Configures logging.

show logging

Shows the log buffer and other logging settings.


show running-config mac-address

To show the mac-address auto configuration in the running configuration, use the show running-config mac-address command in privileged EXEC mode.

show running-config mac-address

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.2(1)

This command was introduced.


Examples

The following is sample output from the show running-config mac-address command:

hostname# show running-config mac-address
no mac-address auto

Related Commands

Command
Description

failover mac address

Sets the active and standby MAC address of a physical interface for Active/Standby failover.

mac address

Sets the active and standby MAC address of a physical interface for Active/Active failover.

mac-address

Manually sets the MAC address (active and standby) for a physical interface or subinterface. In multiple context mode, you can set different MAC addresses in each context for the same interface.

mac-address auto

Auto-generates MAC addresses (active and standby) for shared interfaces in multiple context mode.

show interface

Shows the interface characteristics, including the MAC address.


show running-config mac-address-table

To view the mac-address-table static and mac-address-table aging-time configuration in the running configuration, use the show running-config mac-address-table command in privileged EXEC mode.

show running-config mac-address-table

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was introduced.


Examples

The following is sample output from the show running-config mac-learn command:

hostname# show running-config mac-address-table
mac-address-table aging-time 50
mac-address-table static inside1 0010.7cbe.6101

Related Commands

Command
Description

firewall transparent

Sets the firewall mode to transparent.

mac-address-table aging-time

Sets the timeout for dynamic MAC address entries.

mac-address-table static

Adds static MAC address entries to the MAC address table.

mac-learn

Disables MAC address learning.

show mac-address-table

Shows the MAC address table, including dynamic and static entries.


show running-config mac-learn

To view the mac-learn configuration in the running configuration, use the show running-config mac-learn command in privileged EXEC mode.

show running-config mac-learn

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was introduced.


Examples

The following is sample output from the show running-config mac-learn command:

hostname# show running-config mac-learn
mac-learn disable

Related Commands

Command
Description

firewall transparent

Sets the firewall mode to transparent.

mac-address-table static

Adds static MAC address entries to the MAC address table.

mac-learn

Disables MAC address learning.

show mac-address-table

Shows the MAC address table, including dynamic and static entries.


show running-config mac-list

To display a list of MAC addresses previously specified in a mac-list command with the indicated MAC list number, use the show running-config mac-list command in privileged EXEC mode.

show running-config mac-list id

Syntax Description

id

A hexadecimal MAC address list number.


Defaults

No default behaviors or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was modified to conform to CLI guidelines.


Usage Guidelines

The show running-config aaa command displays the mac-list command statements as part of the AAA configuration.

Examples

The following example shows how to display a MAC address list with the id equal to adc:

hostname(config)# show running-config mac-list adc
mac-list adc permit 00a0.cp5d.0282 ffff.ffff.ffff
mac-list adc deny 00a1.cp5d.0282 ffff.ffff.ffff
mac-list ac permit 0050.54ff.0000 ffff.ffff.0000
mac-list ac deny 0061.54ff.b440 ffff.ffff.ffff
mac-list ac deny 0072.54ff.b440 ffff.ffff.ffff

Related Commands

Command
Description

mac-list

Add a list of MAC addresses using a first-match search.

clear configure mac-list

Remove the indicated mac-list command statements.

show running-config aaa

Display the running AAA configuration values.


show running-config management-access

To display the name of the internal interface configured for management access, use the show running-config management-access command in privileged EXEC mode.

show running-config management-access

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

Preexisting

This command was preexisting.


Usage Guidelines

The management-access command lets you define an internal management interface using the IP address of the firewall interface specified in mgmt_if. (The interface names are defined by the nameif command and displayed in quotes, " ", in the output of the show interface command.)

Examples

The following example shows how to configure a firewall interface named "inside" as the management access interface and display the result:

hostname# management-access inside
hostname# show running-config management-access
management-access inside

Related Commands

Command
Description

clear configure management-access

Removes the configuration of an internal interface for management access of the security appliance.

management-access

Configures an internal interface for management access.


show running-config monitor-interface

To display all monitor-interface commands in the running configuration, use the show running-config monitor-interface command in privileged EXEC mode.

show running-config [all] monitor-interface

Syntax Description

all

(Optional) Shows all monitor-interface commands, including the commands you have not changed from the default.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was introduced.


Usage Guidelines

The monitor-interface command is enabled on all physical interfaces by default. You need to use the all keyword with this command to view this default configuration.

Examples

The following is sample output from the show running-config monitor-interface command. The first time the command is entered without the all keyword, so only the interface that has monitoring enabled appears in the output. The second time the command is entered with the all keyword, so the default monitor-interface configuration is also show.

hostname# show running-config monitor-interface
no monitor-interface outside
hostname#
hostname# show running-config all monitor-interface
monitor-interface inside
no monitor-interface outside
hostname#

Related Commands

Command
Description

monitor-interface

Enables health monitoring of a designated interface for failover purposes.

clear configure monitor-interface

Removes the no monitor-interface commands in the running configuration and restores the default interface health monitoring stance.


show running-config mroute

To display the static multicast route table in the configuration use the show running-config mroute command in privileged EXEC mode.

show running-config mroute [dst [src]]

Syntax Description

dst

The Class D address of the multicast group.

src

The IP address of the multicast source.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

Added keyword running-config.


Examples

The following is sample output from the show running-config mroute command:

hostname# show running-config mroute

Related Commands

Command
Description

mroute

Configures a static multicast route.


show running-config mtu

To display the current maximum transmission unit block size, use the show running-config mtu command in privileged EXEC mode.

show running-config mtu [interface_name]

Syntax Description

interface_name

(Optional) Internal or external network interface name.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

Preexisting

This command was preexisting.


Examples

The following is sample output from the show running-config mtu command:

hostname# show running-config mtu
mtu outside 1500
mtu inside 1500
mtu dmz 1500
hostname# show running-config mtu outside
mtu outside 1500

Related Commands

Command
Description

clear configure mtu

Clears the configured maximum transmission unit values on all interfaces.

mtu

Specifies the maximum transmission unit for an interface.


show running-config multicast-routing

To display the multicast-routing command, if present, in the running configuration, use the show running-config multicast-routing command in privileged EXEC mode.

show running-config multicast-routing

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was introduced.


Usage Guidelines

The show running-config multicast-routing command displays the multicast-routing command in the running configuration. Enter the clear configure multicast-routing command to remove the multicast-routing command from the running configuration.

Examples

The following is sample output from the show running-config multicast-routing command:

hostname# show running-config multicast-routing

multicast-routing

Related Commands

Command
Description

clear configure multicast-routing

Removes the multicast-routing command from the running configuration.

multicast-routing

Enables multicast routing on the security appliance.


show running-config name

To display a list of names associated with IP addresses (configured with the name command), use the show running-config name command in privileged EXEC mode.

show running-config name

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was introduced.


Examples

This example shows how to display a list of names associated with IP addresses:

hostname# show running-config name
name 192.168.42.3 sa_inside
name 209.165.201.3 sa_outside

Related Commands

Command
Description

clear configure name

Clears the list of names from the configuration.

name

Associates a name with an IP address.


show running-config nameif

To show the interface name configuration in the running configuration, use the show running-config nameif command in privileged EXEC mode.

show running-config nameif [physical_interface[.subinterface] | mapped_name]

Syntax Description

mapped_name

(Optional) In multiple context mode, identifies the mapped name if it was assigned using the allocate-interface command.

physical_interface

(Optional) Identifies the interface ID, such as gigabitethernet0/1. See the interface command for accepted values.

subinterface

(Optional) Identifies an integer between 1 and 4294967293 designating a logical subinterface.


Defaults

If you do not specify an interface, this command shows the interface name configuration for all interfaces.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was changed from show nameif.


Usage Guidelines

In multiple context mode, if you mapped the interface ID in the allocate-interface command, you can only specify the mapped name in a context.

This display also shows the security-level command configuration.

Examples

The following is sample output from the show running-config nameif command:

hostname# show running-config nameif
!
interface GigabitEthernet0/0
 nameif inside
 security-level 100
!
interface GigabitEthernet0/1
 nameif test
 security-level 0
!

Related Commands

Command
Description

allocate-interface

Assigns interfaces and subinterfaces to a security context.

clear configure interface

Clears the interface configuration.

interface

Configures an interface and enters interface configuration mode.

nameif

Sets the interface name.

security-level

Sets the security level for the interface.


show running-config names

To display the IP address-to-name conversions, use the show running-config names command in privileged EXEC mode.

show running-config names

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was introduced.


Usage Guidelines

Use with the names command.

Examples

The following example shows how to display the IP address-to-name conversion:

hostname# show running-config names
name 192.168.42.3 sa_inside
name 209.165.201.3 sa_outside

Related Commands

Command
Description

clear configure name

Clears the list of names from the configuration.

name

Associates a name with an IP address.

names

Enables IP address-to-name conversions that you can configured with the name command.

show running-config name

Displays a list of names associated with IP addresses.


show running-config nat

To display a pool of global IP addresses that are associated with a network, use the show running-config nat command in privileged EXEC mode.

show running-config nat [interface_name] [nat_id]

Syntax Description

interface_name

(Optional) Name of the network interface.

nat_id

(Optional) ID of the group of host or networks.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

Added keyword running-config.


Usage Guidelines

This command displays the maximum connection value for the UDP protocol. Every time the UPD maximum connection value is not set, the value will be displayed as 0 by default and will not be applied.


Note In transparent mode, only NAT ID 0 is valid.


Examples

This example shows how to display a pool of global IP addresses that are associated with a network:

hostname# show running-config nat
nat (inside) 1001 10.7.2.0 255.255.255.224 0 0
nat (inside) 1001 10.7.2.32 255.255.255.224 0 0
nat (inside) 1001 10.7.2.64 255.255.255.224 0 0
nat (inside) 1002 10.7.2.96 255.255.255.224 0 0
nat (inside) 1002 10.7.2.128 255.255.255.224 0 0
nat (inside) 1002 10.7.2.160 255.255.255.224 0 0
nat (inside) 1003 10.7.2.192 255.255.255.224 0 0
nat (inside) 1003 10.7.2.224 255.255.255.224 0 0

Related Commands

Command
Description

clear configure nat

Removes the NAT configuration.

nat

Associates a network with a pool of global IP addresses.


show running-config nat-control

To show the NAT configuration requirement, use the show running-config nat-control command in privileged EXEC mode.

show running-config nat-control

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was introduced.


Examples

The following is sample output from the show running-config nat-control command:

hostname# show running-config nat-control
no nat-control

Related Commands

Command
Description

nat

Defines an address on one interface that is translated to a global address on another interface.

nat-control

Allows inside hosts to communicate with outside networks without configuring a NAT rule.


show running-config ntp

To show the NTP configuration in the running configuration, use the show running-config ntp command in privileged EXEC mode.

show running-config ntp

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was introduced.


Examples

The following is sample output from the show running-config ntp command:

hostname# show running-config ntp
ntp authentication-key 1 md5 test2
ntp authentication-key 2 md5 test
ntp trusted-key 1
ntp trusted-key 2
ntp server 10.1.1.1 key 1
ntp server 10.2.1.1 key 2 prefer

Related Commands

Command
Description

ntp authenticate

Enables NTP authentication.

ntp authentication-key

Sets an encrypted authentication key to synchronize with an NTP server.

ntp server

Identifies an NTP server.

ntp trusted-key

Provides a key ID for the security appliance to use in packets for authentication with an NTP server.

show ntp status

Shows the status of the NTP association.


show running-config object-group

To display the current object groups, use the show running-config object-group command in privileged EXEC mode.

show running-config [all] object-group [protocol | service | network | icmp-type | id obj_grp_id]

Syntax Description

icmp-type

(Optional) Displays ICMP type object groups.

id obj_grp_id

(Optional) Displays the specified object group.

network

(Optional) Displays network object groups.

protocol

(Optional) Displays protocol object groups.

service

(Optional) Displays service object groups.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

Preexisting

This command was preexisting.


Examples

The following is sample output from the show running-config object-group command:

hostname# show running-config object-group
object-group protocol proto_grp_1
	protocol-object udp
	protocol-object tcp
object-group service eng_service tcp
	port-object eq smtp
	port-object eq telnet
object-group icmp-type icmp-allowed
	icmp-object echo
	icmp-object time-exceeded

Related Commands

Command
Description

clear configure object-group

Removes all the object group commands from the configuration.

group-object

Adds network object groups.

network-object

Adds a network object to a network object group.

object-group

Defines object groups to optimize your configuration.

port-object

Adds a port object to a service object group.


show running-config passwd

To show the encrypted login passwords, use the show running-config passwd command in privileged EXEC mode.

show running-config {passwd | password}

Syntax Description

passwd | password

You can enter either command; they are aliased to each other.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was changed from the show passwd command.


Usage Guidelines

The password is saved to the configuration in encrypted form, so you cannot view the original password after you enter it. The password displays with the encrypted keyword to indicate that the password is encrypted.

Examples

The following is sample output from the show running-config passwd command:

hostname# show running-config passwd
passwd 2AfK9Kjr3BE2/J2r encrypted

Related Commands

Command
Description

clear configure passwd

Clears the login password.

enable

Enters privileged EXEC mode.

enable password

Sets the enable password.

passwd

Sets the login password.

show curpriv

Shows the currently logged in username and the user privilege level.


show running-config pim

To display the PIM commands in the running configuration, use the show running-config pim command in privileged EXEC mode.

show running-config pim

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was introduced.


Usage Guidelines

The show running-config pim command displays the pim commands entered in global configuration mode. It does not show the pim commands entered in interface configuration mode. To see the pim commands entered in interface configuration mode, enter the show running-config interface command.

Examples

The following is sample output from the show running-config pim command:

hostname# show running-config pim

pim old-register-checksum
pim spt-threshold infinity

Related Commands

Command
Description

clear configure pim

Removes the pim commands from the running configuration.

show running-config interface

Displays interface configuration commands entered in interface configuration mode.


show running-config policy-map

To display all the policy-map configurations or the default policy-map configuration, use the show running-config policy-map command in privileged EXEC mode.

show running-config [all] policy-map [policy_map_name | type inspect [protocol]]

Syntax Description

all

(Optional) Shows all commands, including the commands you have not changed from the default.

policy_map_name

(Optional) Shows the running configuration for a policy map name.

protocol

(Optional) Specifies the type of inspection policy map you want to show. Available types include:

dcerpc

dns

esmtp

ftp

gtp

h323

http

im

mgcp

netbios

p2p

radius-accounting

sip

skinny

snmp

type inspect

(Optional) Shows inspection policy maps.


Defaults

Omitting the all keyword displays only the explicitly configured policy-map configuration.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was introduced.


Usage Guidelines

Specifying the all keyword displays the default policy-map configuration as well as the explicitly configured policy-map configuration.

Examples

The following is sample output from the show running-config policy-map command:

hostname# show running-config policy-map
!
policy-map localmap1
description this is a test.
class firstclass
priority
ids promiscuous fail0close
set connection random-seq# enable
class class-default
!

Related Commands

Command

Description

policy-map

Configures a policy; that is, an association of a traffic class and one or more actions.

clear configure policy-map

Removes the entire policy configuration.


show running-config pop3s

To display the running configuration for POP3S, use the show running-config pop3s command in privileged EXEC mode. To have the display include the default configuration, use the all keyword.

show running-config [all] pop3s

Syntax Description

all

Displays the running configuration including default values.


Defaults

No default behavior or values.

Command History

Release
Modification

7.0(1)(1)

This command was introduced.


Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC

Global configuration

Webvpn


Examples

The following is sample output from the show running-config pop3s command:

hostname# show running-config pop3s

pop3s
 server 10.160.102.188
 authentication-server-group KerbSvr
 authentication aaa

hostname# show running-config all pop3s

pop3s
 port 995
 server 10.160.102.188
 outstanding 20
 name-separator :
 server-separator @
 authentication-server-group KerbSvr
 no authorization-server-group
 no accounting-server-group
 no default-group-policy
 authentication aaa

Related Commands

Command
Description

clear configure pop3s

Removes the POP3S configuration.

pop3s

Creates or edits a POP3S e-mail proxy configuration.


show running-config port-forward

To display the set(s) of applications that WebVPN users can access over forwarded TCP ports, use the show running-config port-forward command in privileged EXEC mode.

show running-config [all] port-forward

Syntax Description

all

(Optional) Displays the running configuration including default values.


Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)(1)

This command was introduced.


Examples

The following is sample output from the show running-config port-forward command:

hostname# show running-config port-forward

port-forward Telnet 3500 10.148.1.5 23
port-forward Telnet 3501 10.148.1.81 23
port-forward Telnet 3502 10.148.1.82 23
port-forward SSH2 4976 10.148.1.81 22
port-forward SSH2 4977 10.148.1.85 22
port-forward Apps1 10143 flask.CompanyA.com 143
port-forward Apps1 10110 flask.CompanyA.com 110
port-forward Apps1 10025 flask.CompanyA.com 25
port-forward Apps1 11533 sametime-im.CompanyA.com 1533
port-forward Apps1 10022 ddts.CompanyA.com 22
port-forward Apps1 54000 10.148.1.5 23
port-forward Apps1 58000 vpn3060-1 23
port-forward Apps1 58001 vpn3005-1 23
hostname#

Related CommandsASA-4#

Command
Description

clear configure port-forward

Removes all port forwarding commands from the configuration. If you include the listname, the security appliance removes only the commands for that list.

port-forward

Configures the set of applications that WebVPN users can access.

port-forward (webvpn)

Enables WebVPN application access for a user or group policy.


show running-config prefix-list

To display the prefix-list command in the running configuration, use the show running-config prefix-list command in privileged EXEC mode.

show running-config prefix-list

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was changed from the show prefix-list command to the show running-config prefix-list command.


Usage Guidelines

The prefix-list description commands always appear before their associated prefix-list commands in the running configuration. It does not matter what order you entered them.

Examples

The following is sample output from the show running-config prefix-list command:

hostname# show running-config prefix-list

!
prefix-list abc description A sample prefix list
prefix-list abc seq 5 permit 192.168.0.0/8 le 24
prefix-list abc seq 10 deny 10.0.0.0/8 le 32 
!

Related Commands

Command
Description

clear configure prefix-list

Clears the prefix-list commands from the running configuration.


show running-config priority-queue

To display the priority queue configuration details for an interface, use the show running-config priority-queue command in privileged EXEC mode.

show running-config priority-queue interface-name

Syntax Description

interface-name

Specifies the name of the interface for which you want to show the priority queue details


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was introduced.


Examples

This example shows the use of the show running-config priority-queue command for the interface named test, and the command output:

hostname# show running-config priority-queue test
priority-queue test
  queue-limit   50
  tx-ring-limit 10
hostname#

Related Commands

Command
Description

clear configure priority-queue

Removes the priority-queue configuration from the named interface.

priority-queue

Configures priority queueing on an interface.

show priority-queue statistics

Shows the statistics for the priority queue configured on the named interface.


show running-config privilege

To display the privileges for a command or a set of commands, use the show running-config privilege command in privileged EXEC mode.

show running-config [all] privilege [all | command command | level level]

Syntax Description

all

(Optional) First occurrence -- Displays the default privilege level.

all

(Optional) Second occurrence -- Displays the privilege level for all commands.

command command

(Optional) Displays the privilege level for a specific command.

level level

(Optional) Displays the commands that are configured with the specified level; valid values are from 0 to 15.


Defaults

No default behaviors or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was modified for this release to conform to CLI guidelines.


Usage Guidelines

Use the show running-config privilege command to view the current privilege level.

Examples

hostname(config)# show running-config privilege level 0
privilege show level 0 command checksum
privilege show level 0 command curpriv
privilege configure level 0 mode enable command enable
privilege show level 0 command history
privilege configure level 0 command login
privilege configure level 0 command logout
privilege show level 0 command pager
privilege clear level 0 command pager
privilege configure level 0 command pager
privilege configure level 0 command quit
privilege show level 0 command version

Related Commands

Command
Description

clear configure privilege

Remove privilege command statements from the configuration.

privilege

Configure the command privilege levels.

show curpriv

Display current privilege level.

show running-config privilege

Display privilege levels for commands.


show running-config regex

To display all regular expressions configured with the regex command, use the show running-config regex command in privileged EXEC mode.

show running-config regex

Syntax Description

This command has no arguments or keywords.

Defaults

No default behaviors or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was introduced.


Examples

The following is sample output of the show running-config regex command, which shows all regular expressions:

hostname# show running-config regex
regex test "string"

Related Commands

Command

Description

class-map type regex

Creates a regular expression class map.

clear configure regex

Clears all regular expressions.

regex

Creates a regular expression.

test regex

Tests a regular expression.


show running-config route

To display the route configuration that is running on the security appliance, use the show running-config route command in privileged EXEC mode.

show running-config [all] route

Syntax Description

No default behavior or values.

Defaults

This command has no arguments or keywords.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

Added keyword running-config.


Examples

The following is sample output from the show running-config route command:

hostname# show running-config route
route outside 10.30.10.0 255.255.255.0 1

Related Commands

Command
Description

clear configure route

Removes the route commands from the configuration that do not contain the connect keyword.

route

Specifies a static or default route for the an interface.

show route

Displays route information.


show running-config route-map

To display the information about the route map configuration, use the show running-config route-map command in privileged EXEC mode.

show running-config route-map [map_tag]

Syntax Description

map_tag

(Optional) Text for the route-map tag.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

Added keyword running-config.


Usage Guidelines

To show all route-maps defined in the configuration, use the show running-config route-map command. To show individual route-maps by name, use the show running-config route-map map_tag command, where map_tag is the name of the route-map. Multiple route maps may share the same map tag name.

Examples

The following is sample output from the show running-config route-map command:

hostname# show running-config route-map
route-map maptag1 permit sequence 10
set metric 5
match metric 3
route-map maptag1 permit sequence 12
set metric 5
match interface backup
match metric 3
route-map maptag2 deny sequence 10
match interface dmz

Related Commands

Command
Description

clear configure route-map

Removes the conditions for redistributing the routes from one routing protocol into another routing protocol.

route-map

Defines the conditions for redistributing routes from one routing protocol into another.


show running-config router

To display the global configuration commands for the specified routing protocol, use the show running-config router command in privileged EXEC mode.

show running-config [all] router [ospf [process_id] | rip]

Syntax Description

all

Shows all router commands, including the commands you have not changed from the default.

ospf

(Optional) Displays the global OSPF configuration commands.

process_id

(Optional) Displays the commands for the selected OSPF process.

rip

(Optional) Displays the global RIP configuration commands.


Defaults

If a routing protocol is not specified, the configuration commands for all configured routing protocols are displayed.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was changed from the show router command to the show running-config router command.


Examples

The following is sample output from the show running-config router ospf command:

hostname# show running-config router ospf 1

router ospf 1
  log-adj-changes detail
  ignore lsa mospf
  no compatible rfc1583
  distance ospf external 200
  timers spf 10 20
  timers lsa-group-pacing 60

The following is sample output from the show running-config router rip command:

router rip
	network 10.0.0.0
	version 2
	no auto-summary

Related Commands

Command
Description

clear configure router

Clears all router commands from the running configuration.

router ospf

Enables an OSPF routing process and enters router configuration mode for that process.

router rip

Enables a RIP routing process and enters router configuration mode for that process.


show running-config same-security-traffic

To display the same-security interface communication, use the show running-config same-security-traffic command in privileged EXEC mode.

show running-config same-security-traffic

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was introduced.


Examples

The following is sample output from the show running-config same-security-traffic command:

hostname# show running-config same-security-traffic

Related Commands

Command
Description

same-security-traffic

Permits communication between interfaces with equal security levels.


show running-config service

To display the system services, use the show running-config service command in privileged EXEC mode.

show running-config service

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

The keyword running-config was added.


Examples

This command shows how to display the system services:

hostname# show running-config service

service resetoutside

Related Commands

Command
Description

service

Enables system services.


show running-config service-policy

To display all currently running service policy configurations, use the show runnig-config service-policy command in privileged EXEC mode.

show running-config [all] service-policy

Syntax Description

all

(Optional) Shows all service policy commands, including the commands you have not changed from the default.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was introduced.


Examples

The following is sample output of the show running-config service-policy command:

hostname# show running-config service-policy

Related Commands

Command
Description

show service-policy

Displays the service policy.

service-policy

Configures service policies.

clear service-policy

Clears service policy configurations.

clear configure service-policy

Clears service policy configurations.


show running-config sla monitor

To display the SLA operation commands in the running configuration, use the show running-config sla monitor command in privileged EXEC mode.

show running-config sla monitor [sla-id]

Syntax Description

sla_id

Specifies the SLA ID for the sla monitor commands being displayed. Valid values are from 1 to 2147483647.


Defaults

If the sla-id is not specified, the sla monitor commands for all SLA operations are displayed.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.2(1)

This command was introduced.


Usage Guidelines

This command displays the sla monitor commands, associated SLA monitor configuration mode commands, and the associated sla monitor schedule command, if present. It does not display the track rtr commands in the configuration.

Examples

The following is sample output from the show running-config sla monitor 5 command. It displays the SLA monitor configuration for the SLA operation with the SLA ID of 5:

hostname# show running-config sla monitor 5

sla monitor 124
 type echo protocol ipIcmpEcho 10.1.1.1 interface outside
 timeout 1000
 frequency 3
sla monitor schedule 124 life forever start-time now

Related Commands

Command
Description

clear configure sla monitor

Removes the sla monitor, and associated commands, from the running configuration.

show sla monitor configuration

Displays configuration values for the specified SLA operation.


show running-config snmp-map

To show the SNMP maps that have been configured, use the show running-config snmp-map command in privileged EXEC mode.

show running-config snmp-map map_name

Syntax Description

map_name

Displays configuration for the specified SNMP map.


.

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was introduced.


Usage Guidelines

The show running-config snmp - map command displays the SNMP maps that have been configured.

Examples

The following is sample output from the show running-config snmp-map command:

hostname# show running-config snmp-map snmp-policy
!
snmp-map snmp-policy
deny version 1
!

Related Commands

Commands
Description

class-map

Defines the traffic class to which to apply security actions.

deny version

Disallows traffic using a specific version of SNMP.

inspect snmp

Enable SNMP application inspection.

snmp-map

Defines an SNMP map and enables SNMP map configuration mode.


show running-config snmp-server

To display all currently running SNMP server configurations, use the show runnig-config snmp-server command in global configuration mode.

show running-config [default] snmp-server

Syntax Description

default

Displays the default snmp server configuration.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Global configuration


Command History

Release
Modification

7.0(1)

This command was introduced.


Examples

The following is an example of the show running-config snmp-server command:

hostname# show running-config snmp-server

Related Commandshostname# show running-config servi

Command
Description

snmp-server

Configures the SNMP server.

clear snmp-server

Clears the SNMP server configuration.

show snmp-server statistics

Displays SNMP server configuration.


show running-config ssh

To show the SSH commands in the current configuration, use the show running-config ssh command in privileged EXEC mode.

show running-config [default] ssh [timeout | version]

show run [default] ssh [timeout]

Syntax Description

default

(Optional) Displays the default SSH configuration values along with the configured values.

timeout

(Optional) Displays the current SSH session timeout value.

version

(Optional) Displays the version of SSH currently being supported.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

The command was changed from the show ssh command to the show running-config ssh command.


Usage Guidelines

This command shows the current ssh configuration. To display only the SSH session timeout value, use the timeout option. To see a list of active SSH sessions, use the show ssh sessions command.

Examples

The following example displays the SSH session timeout:

hostname# show running-config timeout
ssh timeout 5 minutes
hostname# 

Related Commands

Command
Description

clear configure ssh

Clears all SSH commands from the running configuration.

ssh

Allows SSH connectivity to the security appliance from the specified client or network.

ssh scopy enable

Enables a secure copy server on the security appliance.

ssh timeout

Sets the timeout value for idle SSH sessions.

ssh version

Restricts the security appliance to using either SSH Version 1 or SSH Version 2.


show running-config ssl

To display the current set of configured ssl commands, use the show running-config ssl command in privileged EXEC mode.

show running-config ssl

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC

Global configuration


Command History

Release
Modification

7.0(1)(1)

This command was introduced.


Examples

The following is sample output from the show running-config ssl command:

hostname# show running-config ssl
ssl server-version  tlsv1
ssl client-version tlsv1-only
ssl encryption 3des-sha1
ssl trust-point Firstcert

Related Commands

Command
Description

clear config ssl

Removes all ssl commands from the configuration, reverting to the default values.

ssl client-version

Specifies the SSL/TLS protocol version the security appliance uses when acting as a client.

ssl server-version

Specifies the SSL/TLS protocol version the security appliance uses when acting as a server

ssl trust-point

Specifies the certificate trust point that represents the SSL certificate for an interface.


show running-config static

To display all static commands in the configuration, use the show running-config static command in privileged EXEC mode.

show running-config static

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

The keyword running-config was added.


Usage Guidelines

This command displays the maximum connections value for the UDP protocol. If the UDP maximum connections value is "0" or not set, the limit enforcement is disabled.

Examples

This example shows how to display all static commands in the configuration:

hostname# show running-config static
static (inside,outside) 192.150.49.91 10.1.1.91 netmask 255.255.255.255
static (inside,outside) 192.150.49.200 10.1.1.200 netmask 255.255.255.255 tcp 255 0

Note No UDP value connection limit is shown.


Related Commands

Command
Description

clear configure static

Removes all the static commands from the configuration.

static

Configures a persistent one-to-one address translation rule by mapping a local IP address to a global IP address.


show running-config sunrpc-server

To display the information about the SunRPC configuration, use the show running-config sunrpc-server command in privileged EXEC mode.

show running-config sunrpc-server interface_name ip_addr mask service service_type protocol [TCP | UDP] port port [- port] timeout hh:mm:ss

Syntax Description

interface_name

Server interface.

ip_addr

Server IP address.

mask

Network mask.

port port - port

SunRPC protocol port range and optionally, a second port.

protocol

SunRPC transport protocol.

service

Specifies a service.

service_type

Sets the SunRPC service program type.

timeout hh:mm:ss

Specifies the timeout idle time after which the access for the SunRPC service traffic is closed.

TCP

(Optional) Specifies TCP.

UDP

(Optional) Specifies UDP.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was introduced.


Usage Guidelines

The service_type is specified in the sunrpcinfo command.

Examples

The following is sample output from the show running-config sunrpc-server command:

hostname# show running-config sunrpc-server
inside 30.26.0.23 255.255.0.0 service 2147483647 protocol TCP port 2222 timeout 0:03:00

Related Commands

Command
Description

clear configure sunrpc-server

Clears the SunRPC services from the security appliance.

debug sunrpc

Enables debug information for SunRPC.

show conn

Displays the connection state for different connection types, including SunRPC.

sunrpc-server

Creates the SunRPC services table.

timeout

Sets the maximum idle time duration for different protocols and session types, including SunRPC.


show running-config sysopt

To show the sysopt command configuration in the running configuration, use the show running-config sysopt command in privileged EXEC mode.

show running-config sysopt

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was changed from the show sysopt command.


Examples

The following is sample output from the show running-config sysopt command:

hostname# show running-config sysopt
no sysopt connection timewait
sysopt connection tcpmss 1200
sysopt connection tcpmss minimum 400
no sysopt nodnsalias inbound
no sysopt nodnsalias outbound
no sysopt radius ignore-secret
sysopt connection permit-ipsec

Related Commands

Command
Description

clear configure sysopt

Clears the sysopt command configuration.

sysopt connection permit-ipsec

Permits any packets that come from an IPSec tunnel without checking any ACLs for interfaces.

sysopt connection tcpmss

Overrides the maximum TCP segment size or ensures that the maximum is not less than a specified size.

sysopt connection timewait

Forces each TCP connection to linger in a shortened TIME_WAIT state after the final normal TCP close-down sequence.

sysopt nodnsalias

Disables alteration of the DNS A record address when you use the alias command.


show running-config tcp-map

To display the information about the TCP map configuration, use the show running-config tcp-map command in privileged EXEC mode.

show running-config tcp-map [tcp_map_name]

Syntax Description

tcp_map_name

(Optional) Text for the TCP map name; the text can be up to 58 characters in length.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was introduced.


Examples

The following is sample output from the show running-config tcp-map command:

hostname# show running-config tcp-map
tcp-map localmap

Related Commands

Command
Description

tcp-map

Creates a TCP map and allows access to tcp-map configuration mode.

clear configure tcp-map

Clears the TCP map configuration.


show running-config telnet

To display the current list of IP addresses that are authorized to use Telnet connections to the security appliance, use the show running-config telnet command in privileged EXEC mode. You can also use this command to display the number of minutes that a Telnet session can remain idle before being closed by the security appliance.

show running-config telnet [timeout]

Syntax Description

timeout

(Optional) Displays the number of minutes that a Telnet session can be idle before being closed by the security appliance.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

The keyword running-config was added.


Examples

This example shows how to display the current list of IP addresses that are authorized for use by Telnet connections to the security appliance:

hostname# show running-config telnet
2003 Jul 15 14:49:36 %MGMT-5-LOGIN_FAIL:User  failed to
log in from 128.107.183.22 through Telnet
2003 Jul 15 14:50:27 %MGMT-5-LOGIN_FAIL:User  failed to log in from 128.107.183.
22 through Telnet

Related Commands

Command
Description

clear configure telnet

Removes the Telnet connection from the configuration.

telnet

Adds Telnet access to the console and sets the idle timeout.


show running-config terminal

To display the current terminal settings, use the show running-config terminal command in privileged EXEC mode.

show running-config terminal

Syntax Description

This command has no keywords or arguments.

Defaults

The default display width is 80 columns.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was introduced.


Examples

The following example clears the page length setting:

hostname# show running-config terminal

Width = 80, no monitor

Related Commands

Command
Description

clear configure terminal

Clears the terminal display width setting.

terminal

Sets the terminal line parameters.

terminal width

Sets the terminal display width.


show running-config tftp-server

To display the default TFTP server address and directory, use the show running-config tftp-server command in global configuration mode.

show running-config tftp-server

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Global configuration


Command History

Release
Modification

7.0(1)

The running-config keyword was added.


Examples

This example shows how to display the IP/IPv6 address of the default TFTP server and the directory of the configuration file:

hostname(config)# show running-config tftp-server
tftp-server inside 10.1.1.42 /temp/config/test_config

Related Commands

Command
Description

configure net

Loads the configuration from the TFTP server and path you specify.

tftp-server

Configures the default TFTP server address and the directory of the configuration file.


show running-config timeout

To display the timeout value of all protocols, or just a specific one, use the show running-config timeout command in privileged EXEC mode.

show running-config timeout protocol

Syntax Description

protocol

(Optional) Displays the timeout value of the specified protocol. Supported protocols are: xlate, conn, udp, icmp, rpc, h323, h225, mgcp, mgcp-pat, sip, sip_media, and uauth.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

The running-config and mgcp-pat keywords were added.


Examples

This example shows how to display the timeout values for the system:

hostname(config)# show timeout
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 rpc 0:10:00 h3
23 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 sip 0:30:00 sip_media 0:02
:00
timeout uauth 0:00:00 absolute

Related Commands

Command
Description

clear configure timeout

Restores the default idle time durations.

timeout

Sets the maximum idle time duration.


show running-config track

To display track rtr commands in the running configuration, use the show running-config track command in privileged EXEC mode.

show running-config track [track-id]

Syntax Description

track-id

(Optional) Limits the display to the track rtr command with the specified tracking object ID.


Defaults

If the track-id is not specified, all track rtr commands in the running configuration are shown.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.2(1)

This command was introduced.


Examples

The following is sample output from the show running-config track command:

hostname# show running-config track 5

track 5 rtr 124 reachability

Related Commands

Command
Description

clear configure track

Removes the track rtr commands from the running configuration.

show track

Displays information about the objects being tracked.

track rtr

Creates a tracking entry to poll the SLA.


show running-config tunnel-group

To display tunnel group information about all or a specified tunnel group and tunnel-group attributes, use the show running-config tunnel-group command in global configuration or privileged EXEC mode.

show running-config [all] tunnel-group [name [general-attributes | ipsec-attributes | ppp-attributes]]

Syntax Description

all

[Optional] Displays all tunnel-group commands, including the commands you have not changed from the default.

general-attributes

Displays configuration information for general attributes.

ipsec-attributes

Displays configuration information for IPSec attributes.

name

Specifies the name of the tunnel group.

ppp-attributes

Displays configuration information for PPP attributes.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Global configuration

 

   

Privileged EXEC

 

   

Command History

Release
Modification

7.0(1)

This command was introduced.


Examples

The following example entered in global configuration mode, displays the current configuration for all tunnel groups:

hostname<config># show running-config tunnel-group
tunnel-group 209.165.200.225 type IPSec_L2L
tunnel-group 209.165.200.225 ipsec-attributes
pre-shared-key xyzx
hostname<config># 

Related Commands

Command
Description

clear configure tunnel-group

Removes tunnel-group configuration

tunnel-group general-attributes

Enters subconfiguration mode for specifying general attributes for specified tunnel group.

tunnel-group ipsec-attributes

Enters subconfiguration mode for specifying IPSec attributes for specified tunnel group.

tunnel-group

Enters tunnel-group subconfiguration mode for the specified type.


show running-config url-block

To show the configuration for buffers and memory allocation used by URL filtering, use the show running-config url-block command in privileged EXEC mode.

show running-config url-block [ block | url-mempool | url-size ]

Syntax Description

block

Displays the configuration for the maximum number of blocks that will be buffered.

url-mempool

Displays the configuration for the maximum allow URL size (in KB).

url-size

Displays the configuration for the memory resource (in KB) allocated for the long URL buffer.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

Prexisting

This command was previously existing.


Usage Guidelines

The show running-config url-block command displays the configuration for buffers and memory allocation used by URL filtering.

Examples

The following is sample output from the show running-config url-block command:

hostname# show running-config url-block
!
url-block block 56
!

Related Commands

Commands
Description

clear url-block block statistics

Clears the block buffer usage counters.

show url-block

Displays information about the URL cache, which is used for buffering URLs while waiting for responses from an N2H2 or Websense filtering server.

url-block

Manage the URL buffers used for web server responses.

url-cache

Enables URL caching while pending responses from an N2H2 or Websense server and sets the size of the cache.

url-server

Identifies an N2H2 or Websense server for use with the filter command.


show running-config url-cache

To show the cache configuration used by URL filtering, use the show running-config url-cache command in privileged EXEC mode.

show running-config url-cache

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

Preexisting

This command was previously existing.


Usage Guidelines

The show running-config url-cache command displays the cache configuration used by URL filtering.

Examples

The following is sample output from the show running-config url-cache command:

hostname# show running-config url-cache
!
url-cache src_dst 128
!

Related Commands

Commands
Description

clear url-cache statistics

Removes url-cache command statements from the configuration.

filter url

Directs traffic to a URL filtering server.

show url-cache statistics

Displays information about the URL cache, which is used for buffering URLs while waiting for responses from an N2H2 or Websense filtering server.

url-cache

Enables URL caching while pending responses from an N2H2 or Websense server and sets the size of the cache.

url-server

Identifies an N2H2 or Websense server for use with the filter command.


show running-configuration url-list

To display the set(s) of URLs that WebVPN users can access, use the show running-configuration url-list command in privileged EXEC mode.

show running-configuration url-list

Syntax Description

This command has no arguments or keywords.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC

Global configuration

Webvpn


Command History

Release
Modification

7.0(1)(1)

This command was introduced.


Examples

The following is sample output from the show running-configuration url-list command:

hostname# show running-configuration url-list
url-list userURL "SW Engineering" http://10.1.1.2
url-list userURL "My Company" http://www.mycompany.com
url-list userURL "401K Program" https://401k.com
url-list userURL "Exchange5.5 Mail" http://10.1.1.11/exchange
url-list URLlist2 "OWA-2000" http://10.1.1.7/exchange

Related Commands

Command
Description

clear configuration url-list

Removes all url-list commands from the configuration. If you include the listname, the security appliance removes only the commands for that list.

url-list

Configures the set of URLs that WebVPN users can access.

url-list

Enables WebVPN URL access for a specific group policy or user.


show running-config url-server

To show the URL filtering server configuration, use the show running-config url-server command in privileged EXEC mode.

show running-config url-server

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

Preexisting

This command was previously existing.


Usage Guidelines

The show running-config url-server command displays the URL filtering server configuration.

Examples

The following is sample output from the show running-config url-server command:

hostname# show running-config url-server
!
url-server (perimeter) vendor websense host 10.0.1.1
!

Related Commands

Commands
Description

clear url-server

Clears the URL filtering server statistics.

show url-server

Displays information about the URL cache, which is used for buffering URLs while waiting for responses from an N2H2 or Websense filtering server.

url-block

Manages the URL buffers used for web server responses while waiting for a filtering decision from the filtering server.

url-cache

Enables URL caching while pending responses from an N2H2 or Websense server and sets the size of the cache.

url-server

Identifies an N2H2 or Websense server for use with the filter command.


show running-config username

To display the running configuration for a particular user, use the show running-config username command in privileged EXEC mode with the username appended. To display the running configuration for all users, use this command without a username.

show running-config [all] username [name] [attributes]]

Syntax Description

attributes

Displays the specific AVPs for the user(s)

all

(Optional) Displays all username commands, including the commands you have not changed from the default.

name

Provides the name of the user.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC

Global configuration

Username


Command History

Release
Modification

7.0(1)

This command was introduced.


Examples

The following is sample output from the show the running-config username for a user named anyuser:

hostname# show running-config username anyuser
username anyuser password .8T1d6ik58/lzXS5 encrypted privilege 3
username anyuser attributes
vpn-group-policy DefaultGroupPolicy
vpn-idle-timeout 10
vpn-session-timeout 120
vpn-tunnel-protocol IPSec

Related Commands

Command
Description

clear config username

Clears the username database.

username

Adds a user to the security appliance database.

username attributes

Lets you configure attributes for specific users.


show running-config virtual

To display the IP address of the security appliance virtual server, use the show running-config virtual command in privileged EXEC mode.

show running-config [all] virtual

Syntax Description

all

Display the virtual server IP address of all virtual servers.


Defaults

Omitting the all keyword displays the explicitly configured IP address of the current virtual server or servers.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was modified to conform to CLI guidelines.


Usage Guidelines

You must be in privileged EXEC mode to use this command.

Examples

This example displays the show running-config virtual command output for a situation in which there is a previously configured HTTP virtual server:

hostname(config)# show running-config virtual
virtual http 192.168.201.1

Related Commands

Command
Description

clear configure virtual

Removes virtual command statements from the configuration.

virtual

Displays the address for authentication virtual servers.


show running-config vpn load-balancing

To display the current VPN load-balancing virtual cluster configuration, use the show running-config vpn-load-balancing command in global configuration, privileged EXEC, or VPN load-balancing mode.

show running-config [all] vpn load-balancing

Syntax Description

all

Display both the default and the explicitly configured VPN load-balancing configuration.


Defaults

Omitting the all keyword displays the explicitly configured VPN load-balancing configuration.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Global configuration

Privileged EXEC

vpn load-balancing


Command History

Release
Modification

7.0(1)

This command was introduced.


Usage Guidelines

The show running-config vpn load-balancing command also displays configuration information for the following related commands: cluster encryption, cluster ip address, cluster key, cluster port, nat, participate, and priority.

Examples

This example displays show running-config vpn load-balancing command and its output, with the all option enabled:

hostname(config)# show running-config all vpn load-balancing
vpn load-balancing
 no nat
 priority 9
 interface lbpublic test
 interface lbprivate inside
 no cluster ip address
 no cluster encryption
 cluster port 9023
 no participate

Related Commands

Command
Description

clear configure vpn load-balancing

Removes vpn load-balancing command statements from the configuration.

show vpn load-balancing

Displays the VPN load-balancing runtime statistics.

vpn load-balancing

Enters vpn load-balancing mode.


show running-config webvpn

To display the running configuration for webvpn, use the show running-config webvpn command in privileged EXEC mode. To have the display include the default configuration, use the all keyword.

show running-config [all] webvpn [apcf | auto-signon | cache | proxy-bypass | rewrite | sso-server | url-list]

Syntax Description

all

(Optional) Displays the running configuration including default values.

apcf

(Optional) Displays the running configuration for WebVPN APCF.

auto-signon

(Optional) Displays the running configuration for WebVPN auto sign-on.

cache

(Optional) Displays the running configuration for WebVPN caching.

proxy-bypass

(Optional) Displays the running configuration for WebVPN proxy bypass.

rewrite

(Optional) Displays the running configuration for WebVPN content transformation.

sso-server

(Optional) Displays the running configuration for single sign-on.

url-list

(Optional) Displays the running configuration for WebVPN access to URLs.


Defaults

No default behavior or values.

Command History

Release
Modification

7.0(1)(1)

This command was introduced.

7.1(1)

This command was revised.


Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC

Global configuration

WebVPN


Examples

The following is sample output from the show running-config webvpn command:

hostname# show running-configuration webvpn
webvpn
 title WebVPN Services for ASA-4
 title-color green
 default-idle-timeout 0
 nbns-server 10.148.1.28 master timeout 2 retry 2
 accounting-server-group RadiusACS1
 authentication-server-group RadiusACS2
 authorization-dn-attributes CN 

The following is sample output from the show running-config all webvpn command:

hostname#(config-webvpn)# show running-config all webvpn

webvpn
 title WebVPN Services for ASA-4
 username-prompt Username
 password-prompt Password
 login-message Please enter your username and password
 logout-message Goodbye
 no logo
 title-color green
 secondary-color #CCCCFF
 text-color white
 secondary-text-color black
 default-idle-timeout 0
 no http-proxy
 no https-proxy
 nbns-server 10.148.1.28 master timeout 2 retry 2
 accounting-server-group RadiusACS1
 authentication-server-group RadiusACS2
 no authorization-server-group
 default-group-policy DfltGrpPolicy
 authentication aaa
 no authorization-required
 authorization-dn-attributes CN 
hostname#

The following is sample output from the show running-config webvpn sso-server command:

hostname#(config-webvpn)# show running-config webvpn sso-server
sso-server
sso-server bxbsvr type siteminder
web-agent-url http://bxb-netegrity.demo.com/vpnauth/
policy-server-secret cisco1234
sso-server policysvr type siteminder
web-agent-url http://webagent1.mysiteminder.com/ciscoauth/
policy-server-secret Cisco1234
max-retry-attempts 4
request-timeout 10
hostname#(config-webvpn)#

Related CommandsASA-4#

Command
Description

clear configure webvpn

Removes all nondefault WebVPN configuration attributes.

debug webvpn

Displays debug information about WebVPN sessions.

show webvpn

Displays statistics about WebVPN sessions.


show running-config webvpn auto-signon

To display all WebVPN auto-signon assignments in the running configuration, use the show running-config webvpn auto-signon command in global configuration mode.

show running-config webvpn auto-signon

Syntax Description

This command has no arguments or keywords.

Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Global configuration


Command History

Release
Modification

7.1(1)

This command was introduced.


Examples

The following is sample output from the show running-config webvpn auto-signon:

hostname(config)# webvpn
hostname(config-webvpn)# auto-signon allow ip 10.1.1.0 255.255.255.0 auth-type ntlm
hostname(config-webvpn)# auto-signon allow uri *.example.com/* auth-type basic
hostname(config-webvpn)# show running-config webvpn auto-signon
auto-signon allow ip 10.1.1.0 255.255.255.0 auth-type ntlm
auto-signon allow uri *.example.com/* auth-type basic

Related Commands

auto-signon

Configures the security appliance to automatically pass WebVPN login credentials to internal servers.


show running-config zonelabs-integrity

To display the Zone Labs Integrity Server configuration, use the show running-config zonelabs-integrity command in privileged EXEC mode.

show running-config [all] zonelabs-integrity

Syntax Description

all

(Optional) Shows the running configuration including default configuration values.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.2(1)

This command was introduced.


Usage Guidelines

Use this command to display the addresses of all Zone Labs Integrity Servers and the configured values for the active Zone Labs Integrity Server. Use the all parameter to display the default as well as the explicitly configured values.

Examples

The following is sample output from the show running-config zonelabs-integrity command:

hostname# show running-config zonelabs-integrity
zonelabs-integrity server-address 10.0.9.1 10.0.9.2
zonelabs-integrity port 300
hostname#

The following is sample output from the show running-config all zonelabs-integrity command:

hostname# show running-config all zonelabs-integrity
zonelabs-integrity server-address 10.0.9.1 10.0.9.2
zonelabs-integrity port 300
zonelabs-integrity interface none
zonelabs-integrity fail-open
zonelabs-integrity fail-timeout 10
zonelabs-integrity ssl-client-authentication disable
zonelabs-integrity ssl-certificate-port 80
hostname#

Related Commands

Command
Description

clear configure zonelabs-integrity

Clears the Zone Labs Integrity Server configuration.


show running-config smtps

To display the running configuration for smpts, use the show running-config smtps command in privileged EXEC mode. To have the display include the default configuration, use the all keyword.

show running-config [all] smtps

Syntax Description

all

Displays the running configuration including default values.


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)(1)

This command was introduced.


Examples

The following is sample output from the show running-config smtps command:

hostname# show running-config smtps

smtps
server 10.1.1.21
 authentication-server-group KerbSvr
 authentication aaa

hostname# show running-config all smtps

smtps
 port 995
 server 10.1.1.21
 outstanding 20
 name-separator :
 server-separator @
 authentication-server-group KerbSvr
 no authorization-server-group
 no accounting-server-group
 no default-group-policy
 authentication aaa
hostname#

Related CommandsASA-4#

Command
Description

clear configure smtps

Removes the SMTPS configuration.

smtps

Creates or edits an SMTPS e-mail proxy configuration


show running-config vpdn

To display the VPDN configuration used for PPPoE connections, use the show running-config vpdn command in privileged EXEC mode:

show running-config vpdn

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.2(1)

This command was introduced.


Examples

This example shows the use of the show running-config vpdn command and the command output:

hostname# show running-config vpdn
vpdn group telecommuters ppp authentication mschap
vpdn username tomm password ********* store-local

Related Commands

Command
Description

show running-config vpdn group

Shows the current configuration for vpdn group.

show running-config vpdn username

Shows the current configuration for vpdn usernames.


show running-configuration vpn-sessiondb

To display the current set of configured vpnsessiondb commands, use the show running-configuration vpn-sessiondb command in privileged EXEC mode.

show running-configuration [all] vpn-sessiondb

Syntax Description

all

(Optional) Displays all vpn-sessionddb commands, including the commands you have not changed from the default


Defaults

No default behavior or values.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.0(1)

This command was introduced.


Usage Guidelines

As of Release 7.0, this command displays only the VPN maximum sessions limit, if configured.

Examples

The following is sample output for the show running-configuration vpn-sessiondb command:

hostname# show running-configuration vpn-sessiondb

Related Commands

Command
Description

show vpn-sessiondb

Displays sessions with or without extended details, optionally filtered and sorted by criteria you specify.

show vpn-sessiondb summary

Displays a session summary, including total current session, current sessions of each type, peak and total cumulative, maximum concurrent sessions


show running-config wccp

To show the WCCP configuration in the running configuration, use the show running-config wccp command in privileged EXEC mode.

show [all] running-config wccp

Syntax Description

all

Displays the default and explicitly configured configuration information for one or all WCCP commands.


Defaults

This command has no arguments or keywords.

Command Modes

The following table shows the modes in which you can enter the command:

Command Mode
Firewall Mode
Security Context
Routed
Transparent
Single
Multiple
Context
System

Privileged EXEC


Command History

Release
Modification

7.2(1)

This command was introduced.


Examples

The following is sample output from the show running-config wccp command:

hostname# show running-config wccp
wccp web-cache redirect-list wooster group-list jeeves password whatho
hostname# 

Related Commands

Command
Description

wccp

Enables support of WCCP.

wccp redirect

Enters support of WCCP redirection.