The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
To use these commands in System Admin VM, you must be in a user group associated with appropriate command rules and data rules. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
To clear fabric plane information, use the clear controller fabric command in the System Admin EXEC mode.
clear controller fabric { counter | statistics } plane { plane-id | all }
counter |
Clears the fabric up-down counters information. |
statistics |
Clears the fabric statistics counters information. |
plane |
Clears the fabric plane. |
plane-id |
Specifies the fabric plane number. Range is from 0 to 5. |
all |
Clears the fabric information for all planes |
Information for all planes is cleared.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
To view the current status of the counters, execute the show controller fabric plane all command. Later, execute the clear controller fabric command to clear the necessary counter. To view the result of the clear controller fabric command, again execute the show controller fabric plane all command and notice the change.
sysadmin-vm:0_RP0#show controller fabric plane all Mon Jul 16 18:57:15.733 UTC Plane Admin Plane up->dn up->mcast Id State State counter counter -------------------------------------- 0 UP DN 0 0 1 UP UP 0 23 2 UP UP 0 22 3 UP UP 0 19 4 UP DN 0 0 5 UP DN 0 0 > sysadmin-vm:0_RP0# clear controller fabric counter plane 2 Mon Jul 16 18:58:08.122 UTC sysadmin-vm:0_RP0# show controller fabric plane all Mon Jul 16 18:58:18.654 UTC Plane Admin Plane up->dn up->mcast Id State State counter counter -------------------------------------- 0 UP DN 0 0 1 UP UP 0 23 2 UP UP 0 0 3 UP UP 0 19 4 UP DN 0 0 5 UP DN 0 0
To clear control plane Ethernet switch statistics, use the clear controller switch command in the System Admin EXEC mode.
clear controller switch { { fdb | statistics } location node-id | { mlap | sdr } statistics location node-id }
fdb |
Commands for clearing switch forwarding database |
statistics |
Clears the Ethernet switch, MLAP, or SDR interface statistics. |
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot/switch notation. |
mlap |
Clears MLAP statistics |
sdr |
Clears SDR packet statistics |
None
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
To view the current status of the counters, execute the show controller switch statistics command. Later, execute the clear controller switch command to clear the necessary counter. To view the result of the clear controller switch command, again execute the show controller switch statistics command and notice the change.
sysadmin-vm:0_RP0#show controller switch statistics location 0/LC0/LC-SW Wed Aug 28 22:36:03.160 UTC Rack Card Switch Rack Serial Number -------------------------------------- 0 LC0 LC-SW ABCDEFGHIJK Phys State Tx Rx Tx Rx Port State Changes Packets Packets Errors Errors Connects To ------------------------------------------------------------------------ 0 Up 1 359550 135059 0 0 LC CPU (0) 2 Up 5 167398 349026 0 0 RP0 4 Up 5 23392 23460 0 0 RP1 6 Down 1 0 0 0 0 Slice 4 8 Up 1 253073 32683 0 0 CCC (RP0 Ctrl) 9 Up 1 23461 23386 0 0 CCC (RP1 Ctrl) 34 Down 1 0 0 0 0 Slice 1 36 Down 1 0 0 0 0 Slice 0 38 Down 1 0 0 0 0 Slice 2 39 Down 1 0 0 0 0 Slice 3 40 Down 0 0 0 0 0 Bao 41 Up 1 7727 0 0 0 Bao 42 Up 1 0 16338 0 0 Dbg Mgmt Eth0 sysadmin-vm:0_RP0# clear controller switch statistics location 0/LC0/LC-SW all Wed Aug 28 22:36:32.358 UTC Clear all switch port statistics ? [yes,no] yes result Switch statistics cleared successfully. sysadmin-vm:0_RP0# show controller switch statistics location 0/LC0/LC-SW Wed Aug 28 22:36:44.457 UTC Rack Card Switch Rack Serial Number -------------------------------------- 0 LC0 LC-SW ABCDEFGHIJK Phys State Tx Rx Tx Rx Port State Changes Packets Packets Errors Errors Connects To ------------------------------------------------------------------------ 0 Up 0 126 40 0 0 LC CPU (0) 2 Up 0 74 123 0 0 RP0 4 Up 0 22 22 0 0 RP1 6 Down 0 0 0 0 0 Slice 4 8 Up 0 78 30 0 0 CCC (RP0 Ctrl) 9 Up 0 22 22 0 0 CCC (RP1 Ctrl) 34 Down 0 0 0 0 0 Slice 1 36 Down 0 0 0 0 0 Slice 0 38 Down 0 0 0 0 0 Slice 2 39 Down 0 0 0 0 0 Slice 3 40 Down 0 0 0 0 0 Bao 41 Up 0 4 0 0 0 Bao 42 Up 0 0 16 0 0 Dbg Mgmt Eth0 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
To display ethernet status information from the ethernet registers, use the show controller ccc ethernet command in the System Admin EXEC mode.
show controller ccc ethernet { counters | status } [ location node_id ]
counters |
Displays ethernet information from the ethernet counters related registers. |
status |
Displays ethernet information from the ETHERNET_STATUS register. |
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot notation. |
None
Release |
Modification |
---|---|
Release 5.2.3 |
This command was introduced. |
This command provides status for the internal control plane CCC Ethernet connections. Each CCC on the line card (LC) or fabric card (FC) has two dedicated backplane Ethernet connections, one each to the RP0 and RP1 slots. Each connection pass through an Ethernet switch. Hence, there are two segments for each connection, namely, LC/FC to switch, and switch to RP. The counters and link status are related for specific segment of the connection helping in precisely identifying the fault location. For instance, if Ethernet status of CCC on the LC0 does not report any problem (that is, no connectivity issues between LC and the Ethernet switch) but the "Uplink Connection Status" is "Not Available", it indicates that the issue for lack of Ethernet connectivity between CCC driver on RP and LC0 is on the segment connecting the switch and RP.
sysadmin-vm:0_RP0# show controller ccc ethernet status location 0/0 Thu Nov 6 15:40:19.177 UTC CCC Ethernet Status Information For Location: 0/0 --------------------------------------------------------------------------- Uplink Connection Status to Master CCC Driver on 0/RP1: Available CCC Ethernet Port 0 ------------------- LINK_STATUS : Link Valid LINK_SYNC : Link Sync obtained RUDI_C : NOT SET RUDI_I : The core is receiving /I/ ordered sets RUDI_INVLD : NOT SET RXDISPERR : NOT SET RXNOTINTABLE : NOT SET CCC Ethernet Port 1 ------------------- LINK_STATUS : Link Valid LINK_SYNC : Link Sync obtained RUDI_C : NOT SET RUDI_I : The core is receiving /I/ ordered sets RUDI_INVLD : NOT SET RXDISPERR : NOT SET RXNOTINTABLE : NOT SET sysadmin-vm:0_RP0# show controller ccc ethernet counters location 0/0 CCC Ethernet Counters Detail For Location: 0/0 ----------------------------------------------------------------------------- Ethernet Port 0 Ethernet Port 1 --------------- --------------- RX packets : 1796109 RX packets : 1820809 RX bytes : 265125327 RX bytes : 266179825 RX size errors: 0 RX size errors: 0 RX CRC errors : 0 RX CRC errors : 0 TX packets : 1793201 TX packets : 1818744 TX bytes : 168747236 TX bytes : 170262340 CCC-to-CCC Counter Response Packet Counters ------------------- ------------------------ Incoming local : 4 Sent : 3611922 Incoming packet errors: 0 Resent: 0 Incoming filtered : 2122 Errors: 0 Outgoing sent : 11 Outgoing resent : 20 Other Counters Push Packet Counters -------------- -------------------- Ethernet runt errors : 0 Sent : 0 Header errors : 1552 Resent: 0 Request received : 3611918 Errors: 0 CCC-to-CCC received : 3456 Acks : 0 Unknown type received: 0 Nacks : 0
To display card state transition and event information from the CCC (card control chip), use the show controller ccc event-history command in the System Admin EXEC mode.
show controller ccc [slave] event-history { brief | detail } location [node-id]
slave |
Displays card state transitions tracked from the slave CCC driver. Do not use if only one RP is installed in the chassis. |
detail |
Displays detailed information about CCC event history. |
brief |
Displays brief information about CCC event history. |
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot notation. If node-id is not specified, the output is displayed for all nodes. |
Displays event history for master CCC driver.
Release |
Modification |
---|---|
Release 5.2.3 |
This command was introduced. |
sysadmin-vm:0_RP0# show controller ccc event-history brief location 0/2 Tue Aug 5 15:05:00.821 UTC CCC Card Event History for: 0/2 Current State: POWER_UP_FAILED DATE TIME (UTC) STATE EVENT ----- ------------ ---------------------- ------------------------------ 08/05 14:55:17.449 POWER_UP_FAILED ev_wdog_timeout 08/05 14:45:31.265 CCC_DRIVER_INIT if_pwr_up_failed 08/05 14:45:31.260 CHECK_CCC_STATUS if_pwr_up_failed_again 08/05 14:45:31.258 GET_CCC_INFO ev_get_ccc_info_done 08/05 14:45:31.223 WAIT_ETH_READY ev_eth_ready 08/05 14:45:31.157 CHECK_UBLAZE_BOOT ev_ublaze_boot_ok 08/05 14:45:31.124 PON_UP_WARM ev_ccc_reset_done 08/05 14:45:17.489 CCC_IN_RESET ev_pon_up_warm 08/05 14:45:08.921 POWER_UP_FAILED ev_pon_down_warm 08/05 14:35:07.152 POWER_UP_FAILED ev_wdog_timeout 08/05 14:25:20.946 CCC_DRIVER_INIT if_pwr_up_failed 08/05 14:25:20.941 CHECK_CCC_STATUS if_pwr_up_failed_again 08/05 14:25:20.939 GET_CCC_INFO ev_get_ccc_info_done 08/05 14:25:20.923 WAIT_ETH_READY ev_eth_ready 08/05 14:25:20.887 CHECK_UBLAZE_BOOT ev_ublaze_boot_ok 08/05 14:25:20.830 PON_UP_WARM ev_ccc_reset_done sysadmin-vm:0_RP0# show controller ccc event-history detail location 0/2 Tue Aug 5 15:04:07.478 UTC CCC Card Event History for: 0/2 Event buffer info: Total number of events recorded: 692 Number of events available for display: 255 Current State: POWER_UP_FAILED EVENT #: 691 (record index = 179) TIMESTAMP: 2014/08/05 14:55:17.449979 UTC STATE: POWER_UP_FAILED EVENT: ev_wdog_timeout EVENT DESC: CCC watchdog timeout event ERROR INFO: wdog__0 SysAdmin VM Watchdog stage1:0 EVENT #: 690 (record index = 178) TIMESTAMP: 2014/08/05 14:45:31.265829 UTC STATE: CCC_DRIVER_INIT EVENT: if_pwr_up_failed ERROR INFO: Failed to enable main power zone: failure detected in devices CPU VCC, DB main power (0x1f0d) EVENT #: 689 (record index = 177) TIMESTAMP: 2014/08/05 14:45:31.260310 UTC STATE: CHECK_CCC_STATUS EVENT: if_pwr_up_failed_again ERROR INFO: Failed to enable main power zone: failure detected in devices CPU VCC, DB main power (0x1f0d) EVENT #: 688 (record index = 176) TIMESTAMP: 2014/08/05 14:45:31.258124 UTC STATE: GET_CCC_INFO EVENT: ev_get_ccc_info_done EVENT DESC: Retrieval of CCC info is completed EVENT #: 687 (record index = 175) TIMESTAMP: 2014/08/05 14:45:31.223783 UTC STATE: WAIT_ETH_READY EVENT: ev_eth_ready EVENT DESC: Card Ethernet connection is ready EVENT #: 686 (record index = 174) TIMESTAMP: 2014/08/05 14:45:31.157299 UTC STATE: CHECK_UBLAZE_BOOT EVENT: ev_ublaze_boot_ok EVENT DESC: CCC MicroBlaze completed boot operation EVENT #: 685 (record index = 173) TIMESTAMP: 2014/08/05 14:45:31.124094 UTC STATE: PON_UP_WARM EVENT: ev_ccc_reset_done EVENT DESC: CCC RESET operation is completed EVENT #: 684 (record index = 172) TIMESTAMP: 2014/08/05 14:45:17.489647 UTC STATE: CCC_IN_RESET EVENT: ev_pon_up_warm EVENT DESC: PON executing up_warm_reset entry code EVENT #: 683 (record index = 171) TIMESTAMP: 2014/08/05 14:45:08.921444 UTC STATE: POWER_UP_FAILED EVENT: ev_pon_down_warm EVENT DESC: PON executing down_warm_reset entry code EVENT #: 682 (record index = 170) TIMESTAMP: 2014/08/05 14:35:07.152959 UTC STATE: POWER_UP_FAILED EVENT: ev_wdog_timeout
To display the CCC (card control chip) inventory information, use the show controller ccc inventory command in the System Admin EXEC mode.
show controller ccc inventory [ detail | summary | status | version ] [ location node-id ]
detail |
Displays CCC inventory detailed information |
summary |
Displays the card inventory summary. |
status |
Displays CCC status related information. |
version |
Displays CCC version information. |
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot notation. |
Displays all the inventory information for all the nodes.
Release |
Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Release 5.2.3 |
The command output for the summary keyword was enhanced to display the card state information. |
sysadmin-vm:0_RP0#show controller ccc inventory detail Inventory detail information for 0/RP0: ------------------------------------------------------- Card Type = 1 Platform = 4 Board Type = 0x001e0800 Board HW Version = 0.2 Card PID = NC6-RP (master) Card Backplane Slot ID = 0 Card Serial Number = SAD160801NP CCC FPGA Version = 1.0.0 CCC HW Version = 0x201 CCC Core Version = 1.17 CCC PON Version = 1.30 CCC Firmware Version = 1.18 CCC FPGA Image type = WORKING CCC Mac Address 0 = e0:50:72:f4:e8:00 CCC Mac Address 1 = e0:50:72:f4:e8:01 Reboot Reason = WARM START Bios Version = 9.9 PRIMARY Zen FPGA Version = 0.6.3 SDR/VF Mac address start = e0:50:72:f4:e8:03 SDR/VF Mac address end = e0:50:72:f4:e8:14 sysadmin-vm:0_RP0#show controller ccc inventory summary CCC Inventory Summary : BP HW Location Card Type ID Serial Number Ver Card State -------------------------------------------------------------------------------- 0/RP0 NC6-RP (master) 0 SAD15270129 0.1 CARD_READY 0/RP1 NC6-RP (slave) 1 SAD1527012P 0.1 CARD_READY 0/FC0 NC6-FC 8 SAD1618002F 0.2 WAIT_DEV_INIT 0/FC1 NC6-FC 9 SAD153901ZT 0.2 WAIT_DEV_INIT 0/FC4 NC6-FC 12 SAL1803KQEY 1.0 PON_POWERING_UP 0/FC5 NC6-FC 13 SAD16180043 0.2 WAIT_DEV_INIT 0/0 NC6-10X100G-M-K 16 SAL1650UCN9 0.4 PXE_BOOTING 0/4 NC6-10X100G-M-K 20 SAD154502XU 0.1 CARD_READY
Note | The terms "master" and "slave" listed in the Card Type column is indicative of the CCC driver role, and not the active or stand-by state of the RP. On the router, CCC drivers on both RPs actively monitor all the modules in the system at the same time. Either of the CCC drivers can be elected as the master, and the other as the slave. However, only the CCC driver that has the "master" role performs the CCC FPD upgrade on the fabric cards. |
To display the card notification history from the CCC (card control chip), use the show controller ccc notif-history command in the System Admin EXEC mode.
show controller ccc [slave] notif-history { brief | detail } location [node-id]
slave
|
Displays card notification history for the slave CCC driver. Do not use if only one RP is installed in the chassis. |
detail |
Displays detailed information about CCC notification history. |
brief |
Displays brief information about CCC notification history. |
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot notation. If node-id is not specified, the output is displayed for all nodes. |
Displays notification history for master CCC driver.
Release |
Modification |
---|---|
Release 5.2.3 |
This command was introduced. |
sysadmin-vm:0_RP0# show controller ccc notif-history brief location 0/4 Thu Nov 6 16:26:56.829 UTC CCC Card State Notification History for: 0/4 Card State Notification History as seen by Master (0/RP1) DATE TIME (UTC) NOTIF TYPE EVENT TYPE ----- ------------ ------------------------- -------------------------- 11/06 16:24:53.319 CARD_STATE_CHANGE HW_EVENT_OK 11/06 16:24:36.467 CARD_STATE_CHANGE HW_EVENT_POWERED_ON 11/06 16:24:12.294 CARD_STATE_CHANGE HW_EVENT_RESET 11/06 05:53:36.568 CARD_INSERTED HW_EVENT_OK sysadmin-vm:0_RP0# show controller ccc slave notif-history brief location 0/4 Thu Nov 6 16:27:04.280 UTC CCC Card State Notification History for: 0/4 Card Satate Notification History as seen by Slave (0/RP0) DATE TIME (UTC) NOTIF TYPE EVENT TYPE ----- ------------ ------------------------- -------------------------- 11/06 16:24:53.349 CARD_STATE_CHANGE HW_EVENT_OK 11/06 16:24:36.453 CARD_STATE_CHANGE HW_EVENT_POWERED_ON 11/06 16:24:13.437 CARD_STATE_CHANGE HW_EVENT_RESET 11/06 15:37:53.674 CARD_INSERTED HW_EVENT_OK
To display the (online insertion and removal) OIR events on the chassis, use the show controller ccc oir-history command in the System Admin EXEC mode.
show controller ccc [slave] oir-history rack rack_number
slave
|
Displays card OIR history as tracked from the slave CCC driver. Do not use if only one RP is installed in the chassis. |
rack rack_number |
The OIR information is displayed for the cards on the specified rack. |
Displays OIR history from the master CCC driver.
Release |
Modification |
---|---|
Release 5.2.3 |
This command was introduced. |
sysadmin-vm:0_RP0# show controller ccc oir-history rack 0
Cards OIR History of rack: 0
OIR Events as seen by Master (0/RP0)-
DATE TIME (UTC) EVENT LOC CARD TYPE SERIAL NO
----- ------------ ---------- ----- ------------------ -----------
10/09 16:59:14.280 INSERTED 0/0 NC6-10X100G-M-K SAL1650UCN9
10/09 16:58:49.064 REMOVED 0/0 NC6-10X100G-M-K SAL1650UCN9
10/09 16:58:40.215 INSERTED 0/FC0 NC6-FC SAD1618002F
10/09 16:58:18.158 REMOVED 0/FC0 NC6-FC SAD1618002F
10/09 16:52:38.251 DISCOVERED 0/FC0 NC6-FC SAD1618002F
10/09 16:52:38.129 DISCOVERED 0/0 NC6-10X100G-M-K SAL1650UCN9
10/09 16:52:37.990 DISCOVERED 0/FC4 NC6-FC SAL1803KQEY
10/09 16:52:37.865 DISCOVERED 0/FC1 NC6-FC SAD153901ZT
10/09 16:52:37.745 DISCOVERED 0/FC3 NC6-FC SAL1803KQG3
10/09 16:52:37.518 DISCOVERED 0/RP1 NC6-RP SAD15270129
10/09 16:52:26.256 DISCOVERED 0/RP0 NC6-RP SAL171636WW
To display the card power information, use the show controller ccc power command in the System Admin EXEC mode.
show controller ccc power [ detail | summary ] [ location node-id ]
detail |
Displays the card power details. |
summary |
Displays the card power summary. |
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot notation. |
Displays the power summary followed by the detailed power information for all nodes.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
sysadmin-vm:0_RP0#show controller ccc power detail
Fri Jan 15 23:10:58.567 UTC
Power detail : Zone information for 0/RP0:
---------------------------------------------------------
| Power Zone | Power Status | Power Contrl | Power Fault |
---------------------------------------------------------
| 1 | OK | SET | -- |
| 2 | OK | SET | -- |
| 3 | -- | -- | -- |
| 4 | -- | -- | -- |
| 5 | -- | -- | -- |
| 6 | -- | -- | -- |
Power detail : Zone information for 0/RP1:
---------------------------------------------------------
| Power Zone | Power Status | Power Contrl | Power Fault |
---------------------------------------------------------
| 1 | OK | SET | -- |
| 2 | OK | SET | -- |
| 3 | -- | -- | -- |
| 4 | -- | -- | -- |
| 5 | -- | -- | -- |
| 6 | -- | -- | -- |
To display the CCC (card control chip) reset-history information, use the show controller ccc reset-history command in the System Admin EXEC mode.
show controller ccc reset-history [ onboard | onchip ] [ location node-id ]
onboard |
Displays CCC reset history in onboard EEPROM. |
onchip |
Displays on-chip reset history entries since last CCC cold reset. |
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot notation. |
Displays on-chip reset history followed by on-board reset history for all nodes.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
sysadmin-vm:0_RP0#show controller ccc reset-history onchip location 0/1
Fri Jan 15 23:14:13.758 UTC
--location 0/1--
TimeofDay : Sat Jan 1 17:11:29 2011
Uptime : 17:11:50
Resets : 2
proc Reset Reset Register Register Reset
idx IDX Source Command WORD0 WORD1 Time
--- ---- ------------ ------------ ---------- ---------- ----------
0 0 uBlaze AssrtHR 0x00000B10 0x00000000 Thu Jan 1 00:00:00 1970
1 0 uBlaze DeAssrtHR 0x00000B32 0x00000006 Thu Jan 1 00:00:06 1970
-More--
To display controller CCC (card control chip) register information, use the show controller ccc register command in System Admin EXEC mode.
show controller ccc register { group | offset address [ location node-id ] | range start-address end-address [ location node-id ] }
group |
Specifies the register group ID for ccc register information. |
offset address |
Specifies the offset address for ccc register information. Specify the address as a hexadecimal value. Range is from 0x0 to 0x17FFF. |
range start-address end-address |
Specifies the range for ccc register information. Specify a start address in hexadecimal format and an end address in hexadecimal format. Range for start address and end address is from 0x0 to 0x17FFF. |
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot notation. |
None
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
sysadmin-vm:0_RP0#show controller ccc register range 0x0 0x4 location 0/RP0
Fri Jan 15 23:17:42.492 UTC
Register Register
Location Offset Value
----------------------------------
0/rp0 0x0 0x111
0x4 0x0
sysadmin-vm:0_RP0# show controller ccc register group 0 location 0/RP0
Fri Jan 15 23:18:05.697 UTC
LOCATION IDX REGISTER NAME OFFSET VALUE
-----------------------------------------------------------------
0/RP0 0 HW_REVISION 0x0 0x111
1 GLOBAL_RESET_STATUS 0x4 0x0
2 GLOBAL_RESET_COMMAND 0x8 0x0
3 CARD_AND_SLOT 0xC 0x100
4 ALPHA_MESSAGE 0x10 0x30304642
5 CARD_PRESENCE 0x14 0x6C3FA2
6 CARD_ALERT 0x18 0x0
7 HW_JUMPERS 0x1C 0x0
8 GPIO_INPUT_15_0 0x20 0x0
9 GPIO_INPUT_31_16 0x24 0x0
10 GPIO_INPUT_47_32 0x28 0x0
11 GPIO_OUTPUT_15_0 0x2C 0x0
12 GPIO_OUTPUT_31_16 0x30 0x0
13 GPIO_OUTPUT_47_32 0x34 0x0
14 GPIO_OUTPUT_ENABLE_15_0 0x38 0x0
15 GPIO_OUTPUT_ENABLE_31_16 0x3C 0x0
16 GPIO_OUTPUT_ENABLE_47_32 0x40 0x0
17 GP_INTERRUPTS 0x44 0xC049
18 CPU_SIGNALS 0x48 0x40
19 POWER_ZONE_STATUS 0x4C 0x3
20 POWER_ZONE_CONTROL 0x50 0x3
To display the CCC (card control chip) trace information, use the show controller ccc trace command in the System Admin EXEC mode.
show controller ccc trace { all | trace-name } location node-id [ all | trace-attribute ]
trace-name |
Trace name. |
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot notation. |
trace-attributes |
Trace attribute. |
all |
Displays all the details. |
None
Release |
Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Release 5.2.3 |
New trace names were added. |
sysadmin-vm:0_RP0#show controller ccc fpdmgr location 0/3
Mon Aug 12 11:06:13.956 UTC
----------------
12.15.56.012602880:Passing board hw version is 0.2 for fpd CCC FPGA
12.15.56.012882560:Creating instagt_handle rc = 0
12.15.56.551802880:SUCCESS: connected to sm
12.15.56.551987712:FPD register done 0x18362c0
12.15.56.552092032:Passing board hw version is 0.2 for fpd CCC Power-On
12.15.56.552096384:FPD register done 0x18aa630
12.15.56.552121600:Passing board hw version is 0.2 for fpd Ethernet Switch
12.15.56.552123392:FPD register done 0x18aa7e0
12.15.56.558257152:Connected to platform service successful,
saying hello12.15.56.558303488:Requesting nodeid12.15.56.558320512:Requesting
local ip address12.15.56.603181568:SM CONNECT CB returns 0
12.15.56.644174464:Platform nodeid registration response callback12.15.56.644229888:Got
my Nodeid 0/3 (R/S/I)12.15.56.727803264:ds_connect() returned success
12.15.56.727861888:Got ip address registration response
12.15.56.727969024:Got ip address callback
12.15.56.728066176:Activating fpd server with ip 0xc0004c01
12.15.56.785868288:SDORM init success
12.15.56.785995264:Set FPD Ethernet Switch state READY after SDROM ready
12.15.56.791157376:CLR FPD Ethernet Switch status GOLDEN
12.15.56.791162880:Get fpd Ethernet Switch image version 1.32
12.15.56.815722752:Set FPD CCC Power-On state READY after SDROM ready
12.15.56.815745536:CLR FPD CCC Power-On status GOLDEN
12.15.56.815746432:Get fpd CCC Power-On image version 1.30
12.15.56.816411392:Set FPD CCC FPGA state READY after SDROM ready
12.15.56.816432384:CLR FPD CCC FPGA status GOLDEN
12.15.56.816433280:Get fpd CCC FPGA image version 1.14
12.15.56.817161472:Connected to DS, searching for confd
12.15.56.862450048:ds_registered_service_cb called
12.15.56.862451328:ds_registered_service_cb: Status is 0
12.15.56.862451968:Checking has_spinfo
12.15.56.862452608:DS entry found
12.15.56.862453504:fpd_client_connect_confd called
12.15.56.862475520:No service info available for confd
12.15.56.862476160:Return from ds_registered_service_cb
12.15.56.862498048:Confd DS entry found notification
12.15.56.862498688:fpd_client_connect_confd called
12.15.56.862564480: fpd_client_connect_confd(362): DS entry(0) svc confd, ip=192.0.0.1, port=4565, ha_role=ACTIVE issu_role=UNKNOWN, scope=SYSTEM
12.15.56.862585216:setup_fpd_confd_connection called on node location = 0/312.15.56.863445632:Registering Subscription Socket
12.15.56.894000000:Subscription point = 35
12.15.56.920322048:read_conf: return tmp is 1, (return code = 0)
12.15.56.920324096:FPD auto-upgrade DISABLED
12.15.59.492183808:successful connection to Instagt service
12.15.59.492184448:Start Install Agt Notification Registeration
12.15.59.492334336:instagt_register_for_notif rc=0
To display the controller fabric FGID information, use the show controller fabric fgid information command in the System Admin EXEC mode.
show controller fabric fgid information { all | id fgid } [ brief | detail | diagnostics ]
all |
Displays all FGID information. |
id fgid |
Specifies the FGID number. |
brief |
Displays brief information. |
detail |
Displays information in detail. |
diagnostics |
Compares and displays FGID bitmap and SFE bitmap information |
Brief information is displayed.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
When the diagnostics keyword is used and if there is a mismatch between information present in the FGID manager and the SFE driver hardware, an error is displayed.
sysadmin-vm:0_RP0#show controller fabric fgid information id 32240 diagnostics
Starting FGID: 32240
The requested number of FGIDs to display: 1
FGID Information:
FGID number: 32240
FGID Hex bitmap:
0x0000000001000111 0000000000000000 0000000000000000 0000000000000000
0x0000000000000000 0000000000000000 0000000000000000 0000000000000000
0x0000000000000000 0000000000000000 0000000000000000 0000000000000000
0x0000000000000000 0000000000000000 0000000000000000 0000000000000000
0x0000000000000000 0000000000000000 0000000000000000 0000000000000000
FGID Binary bitmap:
0000000000000000000000000000000000000001000000000000000100010001
0000000000000000000000000000000000000000000000000000000000000000
0000000000000000000000000000000000000000000000000000000000000000
0000000000000000000000000000000000000000000000000000000000000000
0000000000000000000000000000000000000000000000000000000000000000
0000000000000000000000000000000000000000000000000000000000000000
0000000000000000000000000000000000000000000000000000000000000000
0000000000000000000000000000000000000000000000000000000000000000
0000000000000000000000000000000000000000000000000000000000000000
0000000000000000000000000000000000000000000000000000000000000000
0000000000000000000000000000000000000000000000000000000000000000
0000000000000000000000000000000000000000000000000000000000000000
0000000000000000000000000000000000000000000000000000000000000000
0000000000000000000000000000000000000000000000000000000000000000
0000000000000000000000000000000000000000000000000000000000000000
0000000000000000000000000000000000000000000000000000000000000000
0000000000000000000000000000000000000000000000000000000000000000
0000000000000000000000000000000000000000000000000000000000000000
0000000000000000000000000000000000000000000000000000000000000000
0000000000000000000000000000000000000000000000000000000000000000
FGID associated fabricq Ids:
[4] :=
0/0/0, 0/0/4, 0/1/2, 0/4/0,
FGID associated client application:
client id = 2, client name = Jabed, SDR name = default-sdr
FGID bitmap at location 0/SM1/0, Status: ERR
s123: 0000000000000000000000000000000000000000000000000000000000000000
-0000000000000000000000000000000000000001000000000000000000000000
FGID bitmap at location 0/SM1/1, Status: ERR
s123: 0000000000000000000000000000000000000000000000000000000000000000
-0000000000000000000000000000000000000001000000000000000000000000
FGID bitmap at location 0/SM4/0, Status: ERR
s123: 0000000000000000000000000000000000000000000000000000000000000000
-0000000000000000000000000000000000000001000000000000000000000000
FGID bitmap at location 0/SM4/1, Status: ERR
s123: 0000000000000000000000000000000000000000000000000000000000000000
-0000000000000000000000000000000000000001000000000000000000000000
To display the controller fabric FGID program-error, use the show controller fabric fgid program-error command in the System Admin EXEC mode.
show controller fabric fgid program-error { all | startfgid endfgid }
all |
Displays all FGID program-error. |
startfgid |
Specifies the start FGID id. Range is from 0 to 524287. |
endfgid |
Specifies the end FGID id. Range is from 0 to 524287. |
None
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Use this command for diagnostics. Execution time of the command depends on the number of FGIDs. The total number of erroneous FGIDs are displayed. However, only 10 FGIDs that have errors are displayed. To identify if a particular FGID has an error, update the range of the FGID in the command.
sysadmin-vm:0_RP0# show controller fabric fgid program-error 0 524287
Rack 0:
Fgids: 32240 32241 32242 32243 32244 32245 32246 32247 32248 32249 ...
Total: 14
To display the controller fabric FGID allocated resource information, use the show controller fabric fgid resource command in the System Admin EXEC mode.
show controller fabric fgid resource { all | sdr sdr-name { all | application application-name id fgid-id elements num-elements } }
all |
Displays FGID resource information for all SDRs on the current system. |
||
sdr |
Name of the SDR. The default-sdr is the only available option. |
||
sdr-name |
Specifies the name of the SDR. The default-sdr is the only available option. |
||
all |
Specifies all secure domain routers. |
||
application |
Specifies the allocated FGID resource per application. |
||
application-name |
Specifies the application name. The default available options are:
|
||
id fgid-id |
Indicates the starting fgid number. Range is from 0 to 524288 |
||
elements num-elements |
Indicates the fabric FGIDs. The number ranges from 0 to 524288. |
None
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Only if FGIDs are used by the application, the information is displayed.
sysadmin-vm:0_RP0# show controller fabric fgid resource sdr default-sdr application some_app id 0 elements 524287
====================================================
Displaying FGID Info for:
SDR: default-sdr APPLICATION : some_app
32240, 32241, 32242, 32243, 32244, 32245, 32246, 32247, 32248, 32249
32250, 32251, 32252, 32253, 32254, 32255, 32256, 32257, 32258, 32259
32260, 32261, 32262, 32263, 32264, 32265, 32266, 32267, 32268, 32269
32270, 32271, 32272, 32273, 32274, 32275, 32276, 32277, 32278, 32279
32280, 32281, 32282, 32283, 32284, 32285, 32286, 32287, 32288, 32289
32290, 32291, 32292, 32293, 32294, 32295, 32296, 32297, 32298, 32299
32300, 32301, 32302, 32303, 32304, 32305, 32306, 32307, 32308, 32309
32310, 32311, 32312, 32313, 32314, 32315, 32316, 32317, 32318, 32319
32320, 32321, 32322, 32323, 32324, 32325, 32326, 32327, 32328, 32329
32330, 32331, 32332, 32333, 32334, 32335, 32336, 32337, 32338, 32339
32340, 32341, 32342, 32343, 32344, 32345, 32346, 32347, 32348, 32349
32350, 32351, 32352, 32353, 32354, 32355, 32356, 32357, 32358, 32359
32360, 32361, 32362, 32363, 32364, 32365, 32366, 32367, 32368, 32369
32370, 32371, 32372, 32373, 32374, 32375, 32376, 32377, 32378, 32379
32380, 32381, 32382, 32383, 32384, 32385, 32386, 32387, 32388, 32389
32390, 32391, 32392, 32393, 32394, 32395, 32396, 32397, 32398, 32399
32400, 32401, 32402, 32403, 32404, 32405, 32406, 32407, 32408, 32409
32410, 32411, 32412, 32413, 32414, 32415, 32416, 32417, 32418, 32419
32420, 32421, 32422, 32423, 32424, 32425, 32426, 32427, 32428, 32429
32430, 32431, 32432, 32433, 32434, 32435, 32436, 32437, 32438, 32439
32440, 32441, 32442, 32443, 32444, 32445, 32446, 32447, 32448, 32449
32450, 32451, 32452, 32453, 32454, 32455, 32456, 32457, 32458, 32459
32460, 32461, 32462, 32463, 32464, 32465, 32466, 32467, 32468, 32469
32470, 32471, 32472, 32473, 32474, 32475, 32476, 32477, 32478, 32479
32480, 32481, 32482, 32483, 32484, 32485, 32486, 32487, 32488, 32489
32490, 32491, 32492, 32493, 32494, 32495, 32496, 32497, 32498, 32499
32500, 32501, 32502, 32503, 32504, 32505, 32506, 32507, 32508, 32509
32510, 32511, 32512, 32513, 32514, 32515, 32516, 32517, 32518, 32519
32520, 32521, 32522, 32523, 32524, 32525, 32526, 32527, 32528, 32529
32530, 32531, 32532, 32533, 32534, 32535, 32536, 32537, 32538, 32539
32540, 32541, 32542, 32543, 32544, 32545, 32546, 32547, 32548, 32549
32550, 32551, 32552, 32553, 32554, 32555, 32556, 32557, 32558, 32559
32560, 32561, 32562, 32563, 32564, 32565, 32566, 32567, 32568, 32569
32570, 32571, 32572, 32573, 32574, 32575, 32576, 32577, 32578, 32579
32580, 32581, 32582, 32583, 32584, 32585, 32586, 32587, 32588, 32589
32590, 32591, 32592, 32593, 32594, 32595, 32596, 32597, 32598, 32599
32600, 32601, 32602, 32603, 32604, 32605, 32606, 32607, 32608, 32609
32610, 32611, 32612, 32613, 32614, 32615, 32616, 32617, 32618, 32619
32620, 32621, 32622, 32623, 32624, 32625, 32626, 32627, 32628, 32629
32630, 32631, 32632, 32633, 32634, 32635, 32636, 32637, 32638, 32639
To display resource statistical information for the fabric group ID (FGID), use the show controller fabric fgid statistics command in the System Admin EXEC mode.
show controller fabric fgid statistics { all | pool | sdr | system } [ brief | detail ]
all |
Specifies all FGID resource statistical information for the logical router and FGID resource pools. |
sdr |
Specifies FGID resource statistics about the secure domain router (SDR). |
pool |
Specifies FGID statistical information about the resource pool. |
system |
Specifies FGID resource statistics for the entire physical router. |
brief |
Specifies brief information about FGIDs. |
detail |
Specifies detailed information about FGIDs. |
Brief information is displayed.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
sysadmin-vm:0_RP0#show controller fabric fgid statistics all
Fabric FGID Resource Statistics Information:
System wide Fabric multicast resource statistics:
Total number of FGIDS in the system is 524288
Current number of InUse FGIDS in the system is 0
High Water Mark of InUse FGIDS in the system is 0
Per SDR basis Fabric multicast resource statistics:
SDR Current HighWater Mark
Name FGIDs InUse FGIDs
--------------------------------------------------------------------------------
default-sdr 0 0
Per pool basis Fabric multicast resource statistics:
Pool Pool Pool Total Current High Water Mark
ID Name Type FGIDs FGIDs InUse FGIDs
--------------------------------------------------------------------------------
0 SDR Shared 514048 0 0
1 NON_SDR Dedicated 10240 0
To display the FGID trace information, use the show controller fabric fgid trace command in the System Admin EXEC mode.
show controller fabric fgid trace { all | trace-name } location node-id [ all | trace-attribute ]
trace-name |
Trace name. |
||
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot notation.
|
||
trace-attribute |
Trace attribute. |
||
all |
Displays all the details. |
None
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Use this command for FGID process diagnostics. This command displays information only from the Route Processor (RP).
sysadmin-vm:0_RP0#show controller fabric fgid trace all location 0/RP0
Fri Aug 23 10:17:49.373 UTC
----------------
19.49.04.359137280:FGID Server CTRACE init done
19.49.04.409993216: @msc_entity id="0/2123" display_name="fgid"
19.49.04.437780480:@msc_event entity_id="0/2123/2123" time="1376077744439000000"
label="connecting to pm_lib with endpoint (0x0, 2020) (hdl=0x0x27983c0)"
type="Connection" completed="false" @msc_source pairing_id="0/2123/con_0x27983c0"
type="Lane"
19.49.04.452984832:CIPC:CONN (hdl=0x2798810):cipc_connect():invoked on endpoint
(0.0.0.0, 2020)
19.49.04.454033408:FGID Server PM init done
19.49.04.541065216: @msc_entity id="0/2123" display_name="fgid"
19.49.04.541065216:@msc_event entity_id="0/2123/2123" time="1376077744542000000"
label="requesting connection to platform_local (CAPI hdl=0x27b48f0, CIPC hdl = 0x27b5130)"
type="Connection" completed="false"
19.49.04.541065216:DS handle 0x27b48f0 instantiated for platform_local client handle
19.49.04.573046784: @msc_entity id="0/2123" display_name="fgid"
19.49.04.583008256:@msc_event entity_id="0/2123/2123" time="1376077744584000000"
label="requesting connection to calvados_ds (CAPI hdl=0x27d7ac0, CIPC hdl = 0x27d7ef0)"
type="Connection" completed="false"
19.49.04.583008256:@msc_event entity_id="0/2123/2123" time="1376077744584000000"
label="connecting to calvados_ds with endpoint (0x7f000001, 7400) (hdl=0x0x27d7ac0)"
type="Connection" completed="false" @msc_source pairing_id="0/2123/con_0x2
--More--
To display the FSDB-aggregator trace information, use the show controller fabric fsdb-aggregator trace command in the System Admin EXEC mode.
show controller fabric fsdb-aggregator trace trace-name location node-id trace-attribute
trace-name |
Trace name. |
||
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot notation.
|
||
trace-attribute |
Trace attribute. |
None
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Use this command for FSDB (fabric system database) aggregator functionality diagnostics. This command displays information only from the Route Processor (RP).
sysadmin-vm:0_RP0#show controller fabric fsdb-aggregator trace all location 0/RP0
Fri Aug 23 10:41:12.553 UTC
----------------
19.49.03.688914432:FSDB Aggregator CTRACE init done
19.49.03.767557632: @msc_entity id="0/2111" display_name="fsdbagg"
19.49.03.809500672:@msc_event entity_id="0/2111/2111" time="1376077743811000000"
label="connecting to pm_lib with endpoint (0x0, 2020) (hdl=0x0x15293c0)" type="Connection"
completed="false" @msc_source pairing_id="0/2111/con_0x15293c0" type="Lane"
19.49.03.825753600:CIPC:CONN (hdl=0x1529810):cipc_connect():invoked on endpoint
(0.0.0.0, 2020)
19.49.03.826802176:FSDB Aggregator PM init done
19.49.03.973602816: @msc_entity id="0/2111" display_name="fsdbagg"
19.49.03.973602816:@msc_event entity_id="0/2111/2111" time="1376077743975000000"
label="requesting connection to platform_local (CAPI hdl=0x1545900, CIPC hdl = 0x1546140)"
type="Connection" completed="false"
19.49.03.973602816:DS handle 0x1545900 instantiated for platform_local client handle
19.49.04.011010048: @msc_entity id="0/2111" display_name="fsdbagg"
19.49.04.036700160:@msc_event entity_id="0/2111/2111" time="1376077744037000000"
label="requesting connection to calvados_ds (CAPI hdl=0x1568ad0, CIPC hdl = 0x1568f00)"
type="Connection" completed="false"
19.49.04.036700160:@msc_event entity_id="0/2111/2111" time="1376077744037000000"
label="connecting to calvados_ds with endpoint (0x7f000001, 7400) (hdl=0x0x1568ad0)"
type="Connection" completed="false" @msc_source pairing_id="0/2111/con_0x1
--More--
To display plane availability status information, use the show controller fabric fsdb-pla command in the System Admin EXEC mode.
show controller fabric fsdb-pla rack { rack-number [ destination id ] | all }
rack-number |
Specifies the rack number. The value can range from 0 to 15 or from F0 to F3. |
destination id |
Indicates the destination. The id can range from 0 to 1023 or can be provided in the asic location format (R/S/A). |
all |
Displays plane availability status of all the racks. |
None
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Only one rack (R0) and all options are supported.
sysadmin-vm:0_RP0#show controller fabric fsdb-pla rack 0 destination 1
Amba id: 1(0/0/1)
========================
plane id:1
-----------------------------------------------------
Asic Reachability mask Links
-----------------------------------------------------
0 0x0000200200000000-0000080000000000 3
1 0x0002022000000000-0000000000000000 3
plane id:2
-----------------------------------------------------
Asic Reachability mask Links
-----------------------------------------------------
0 0x0000200200000000-0000080000000000 3
1 0x0002022000000000-0000000000000000 3
plane id:3
-----------------------------------------------------
Asic Reachability mask Links
-----------------------------------------------------
0 0x0000200200000000-0000080000000000 3
1 0x0002022000000000-0000000000000000 3
To display the FSDB-server information, use the show controller fabric server trace command in the System Admin EXEC mode.
show controller fabric fsdb-server trace { all | trace-name } location node-id [ all | trace-attribute ]
trace-name |
Trace name. |
||
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot notation.
|
||
trace-attribute |
Trace attribute. |
None
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Use this command for FSDB (fabric system database) server functionality diagnostics. This command displays information only from the Route Processor (RP).
sysadmin-vm:0_RP0#show controller fabric fsdb-server trace all location 0/RP0
Fri Aug 23 10:35:06.638 UTC
----------------
19.49.03.090701824:FSDB Server CTRACE init done
19.49.03.177733632: @msc_entity id="0/2104" display_name="fsdb"
19.49.03.242745344:@msc_event entity_id="0/2104/2104" time="1376077743244000000"
label="connecting to pm_lib with endpoint (0x0, 2020) (hdl=0x0x2501110)"
type="Connection" completed="false" @msc_source pairing_id="0/2104/con_0x2501110"
type="Lane"
19.49.03.249561088:CIPC:CONN (hdl=0x2501560):cipc_connect():invoked on endpoint
(0.0.0.0, 2020)
19.49.03.378535936: @msc_entity id="0/2104" display_name="fsdb"
19.49.03.378535936:@msc_event entity_id="0/2104/2104" time="1376077743379000000"
label="requesting connection to platform_local (CAPI hdl=0x251d640, CIPC hdl = 0x251de80)"
type="Connection" completed="false"
19.49.03.378535936:DS handle 0x251d640 instantiated for platform_local client handle
19.49.03.396886016: @msc_entity id="0/2104" display_name="fsdb"
19.49.03.453509120:@msc_event entity_id="0/2104/2104" time="1376077743454000000"
label="requesting connection to calvados_ds (CAPI hdl=0x2540a00, CIPC hdl = 0x2540e30)"
type="Connection" completed="false"
19.49.03.453509120:@msc_event entity_id="0/2104/2104" time="1376077743454000000"
label="connecting to calvados_ds with endpoint (0x7f000001, 7400) (hdl=0x0x2540a00)"
type="Connection" completed="false" @msc_source pairing_id="0/2104/con_0x2540a00"
type="Lane"
--More--
To display the general condition of the fabric sub-system, use the show controller fabric health command in the System Admin EXEC mode.
show controller fabric health
This command has no keywords or arguments.
None
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Use the command for diagnostics only.
sysadmin-vm:0_RP0#show controller fabric health
Mon Jul 23 08:30:56.170 UTC
Fabric System Health
---------------------
Flags: T - Total, U - Up, A - Admin Down
L - LCC, M - Mcast Down, Y - Yes
F - FCC, D - Down, N - No or Not Ok
V - Valid,
Collaborator Process State:
------------------------------
FSDB Aggregator: OK
+-----------+--+
|Rack id | 0|
+-----------+--+
|FSDB status|Ok|
+-----------+--+
|SFE status |Ok|
+-----------+--+
Router Health:
-----------------
Rack Planes SFE Asics Fia Asics
T/L/F U/M/D/A T/U/D T/U/D
------------------------------------------------------
1/1/0 2/0/4/1 6/6/0 15/8/7
Plane Admin Plane Racks Data
id state state in issue drop/error
-----------------------------------------------------------
0 UP DN 1 No
1 DN DN 1 Yes
2 UP UP 0 Yes
3 UP UP 0 Yes
4 UP DN 1 No
5 UP DN 1 No
-----------------------------------------------------------
Rack Health:
-------------
Rack: 0, Type: LCC
SFE Asics FIA Asics Planes Amba
T/U/D T/U/D U/M/D T/V
------------------------------------------
6/6/0 15/8/7 2/0/4 15/8
Plane Plane SFE Asics Amba
id state T/U/D Reachable
--------------------------------------
0 DN 0/0/0 0
1 DN 2/2/0 0
2 UP 2/2/0 8
3 UP 2/2/0 8
4 DN 0/0/0 0
5 DN 0/0/0 0
--------------------------------------
To display link information for a specific fabric port, use the show controller fabric link port command in the System Admin EXEC mode.
show controller fabric link port fia [ link-location | all ] [ state { down | mismatch | up } ] [ brief | detail ]
show controller fabric link port { s1 | s2 | s3 } [ link-location | all ] [ state { down | mismatch | up } | statistics ] [ brief | detail ]
port |
|
fia |
Displays the information of the fabric interface asic (fia) link port. |
s1 |
Displays the information of the s1 link port. |
s2 |
Displays the information of the s2 link port. |
s3 |
Displays the information of the s3 link port. |
statistics |
Displays the statistics. |
link-location |
|
all |
Displays all the fabric link information for specified ports. |
state |
Displays the link state. |
down |
Displays links information of the specified ports that are in down state. |
mismatch |
Displays links information of the specified ports whose operational state and admin state do not match. |
up |
Displays links information of the specified ports that are in up state. |
brief |
Displays summarized fabric link information. |
detail |
Displays detailed fabric link information. |
Brief information is displayed.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
The supported link ports are FIA (fabric interface asic), s1, and s3.
sysadmin-vm:0_RP0#show controller fabric link port s1 0/FC1/0/3 detail
Mon Jul 23 08:34:55.121 UTC
Sfe Port Admin Other Near-end Far-end
R/S/A/P /Oper End Bport Bport
State
--------------------------------------------------------------
0/FC1/0/3 UP/DN 0/1/2/14
+-----------------------------------------------------------------------+
| Timestamp Event(s) |
+-----------------------------------------------------------------------+
2013 Jul 23 01:48:53.000 OPER_DN
2013 Jul 23 02:08:22.000 OPER_UP
2013 Jul 23 02:15:44.000 OPER_DN
2013 Jul 23 02:15:47.4294 OPER_UP
2013 Jul 23 02:18:00.000 OPER_DN
To display the system fabric plane information, use the show controller fabric plane command in the System Admin EXEC mode.
show controller fabric plane { plane-id | all } [statistics] [ brief | detail ]
plane-id |
Plane number. Range is from 0 to 5. |
all |
Displays information about all the system fabric planes. |
statistics |
Displays plane statistics. |
brief |
Displays brief information about the system fabric plane or plane statistics. |
detail |
Displays detailed information about the system fabric plane or plane statistics. |
Brief information is displayed.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Use the show controllers fabric plane command to monitor the fabric plane status, and the cell traffic and error statistics to or from the fabric plane.
sysadmin-vm:0_RP0#show controller fabric plane 3
Plane Admin Plane up->dn up->mcast
Id State State counter counter
--------------------------------------
3 UP DN 0 0
To display information about fabric ASICs, use the show controller fabric sfe command in the System Admin EXEC mode.
show controller fabric sfe { b2b | fia | s123 | s13 | s2 } { asic-location | all } [ brief | detail ]
b2b |
Displays b2b (back to back) asic information. |
fia |
Displays fia (fabric interface asic) information |
s123 |
Displays information about the s123 asic of the switch fabric element. |
s13 |
Displays information about the s13 asic of the switch fabric element. |
s2 |
Displays information about the s2 asic of the switch fabric element. |
asic-location |
|
all |
Displays all ASICs information about the switch fabric elements. |
brief |
Displays summarized information. |
detail |
Displays detailed information. |
Brief information is displayed.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Note | Only FIA and s123 asics are supported in this release. The b2b, s13, and s2 asics are not supported in this release. |
sysadmin-vm:0_RP0# show controller fabric sfe s123 0/FC1/0 detail Mon Jul 23 08:32:27.325 UTC Sfe Admin Oper R/S/A State State ----------------------------- 0/FC1/0 UP UP +-----------------------------------------------------------------------+ | Timestamp Event(s) | +-----------------------------------------------------------------------+ 2012 Jul 22 23:51:25.000 OPER_UP sysadmin-vm:0_RP0#
sysadmin-vm:0_RP0#show controller fabric sfe s123 all
Wed Aug 7 09:00:44.600 UTC
Sfe Admin Oper
R/S/A State State
-----------------------------
0/FC0/0 UP UP
0/FC0/1 UP UP
To display the system fabric plane information from the standby process of the FSDB aggregator, use the show controller standby fabric plane command in the System Admin EXEC mode.
show controller fabric standby plane { plane-id | all } [statistics] [ brief | detail ]
plane-id |
Plane number. Range is from 0 to 5. |
all |
Displays information about all the system fabric planes. |
statistics |
Displays plane statistics. |
brief |
Displays brief information about the system fabric plane or plane statistics. |
detail |
Displays detailed information about the system fabric plane or plane statistics. |
Brief information is displayed.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Use theshow controller standby fabric plane command for diagnostics only.
sysadmin-vm:0_RP0#show controller fabric standby plane 3
Wed Aug 7 09:58:32.671 UTC
Plane Admin Plane up->dn up->mcast
Id State State counter counter
--------------------------------------
3 UP DN 0 0
To display the sfe driver information, use the show controller sfe driver rack command in the System Admin EXEC mode.
show controller sfe driver rack rack-number
rack-number |
Specifies the rack number from which to display information. |
None
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
The show controller sfe driver rack command is used to view whether the driver is connected with collaborator processes, libraries, and ASICs state. Used for diagnostics only.
sysadmin-vm:0_RP0#show controller sfe driver rack 0
Mon Aug 12 06:18:01.497 UTC
Mon Aug 12 06:18:01.518 UTC
=========================================================================
SFE Driver information
=========================================================================
Driver Version: 1 (1.1)
Functional role: Active, ISSU role: NA
Rack: 0/RP0, Type: lcc, Number: 0, IP Address: 192.0.0.1
Startup time : 1970 Jan 1 00:00:00.000
Availability Masks :
Card: 0x1 Asic: 0x3 Exp Asic: 0x3
Unicast/Multicast (ratio) : 0
+----------------------------------------------------------------+
|Process | Connection | Registration| Connection | DLL |
|/Lib | status | status | requests | registration |
+----------------------------------------------------------------+
| PM | Active | n/a | 1| n/a |
| PL-LOCAL| Active | Active | 1| n/a |
| FSDB | Active | Active | 1| n/a |
| FGID | Active | Active | 1| n/a |
| CM | Active | Active | 1| n/a |
--More--
To display the sfe receiver link information, use the show controller sfe link-info rx command in the System Admin EXEC mode.
show controller sfe link-info rx start-link-num end-link-num { flap | topo } instance { asic-instance | all } location { node-id | all } [detail]
start-link-num |
Specifies the first value of a range of values. |
end-link-num |
Specifies the last value of a range of values. |
flap |
Displays link flap information. |
topo |
Displays topology information. |
instance |
Indicates an ASIC instance. |
asic-instance |
Displays link information for a specific ASIC instance. Range is from 0 to 5. |
all |
Displays link information of all ASIC instances. |
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot notation. |
detail |
Displays detailed information. |
Brief information is displayed.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Use the topo keyword to view the topological information. When the topo keyword is used, the Flag column in the example output indicates the reason why the link is not operational.
To identify the number of times the link fluctuated, use the flap keyword. The flap keyword is used only for diagnostics. The detail keyword displays the link history information. When the detail keyword is used, the Down Reason column in the example output indicates the reason why the link is down.
sysadmin-vm:0_RP0#show controller sfe link-info rx 2 3 topo instance all location all
Mon Aug 12 08:14:27.568 UTC
---------------------------------------------------------------------------------
Node ID: 0_RP0 Instance: 0
Flags:
D - Power Down, I - Init/deinit, T - Invalid Topo, B - Bad link conn
E - Rcvr End Rst, F - No Far-end, C - CRC error, S - Size error
G - Code Grp err, M - Misalign, L - No Sig Lock, R - No Reachability Cells
---------------------------------------------------------------------------------
Link ID Link Asic Plane EN/ Flags Far-End Far-End
Spd Stg. /Group Oper Link (FSDB) Link (HW)
(Gbps) Status
---------------------------------------------------------------------------------
0/FC0/0/2 11.5 S1 0/0 UP/DN D........... NC n/a
0/FC0/0/3 11.5 S1 0/0 UP/DN D........... NC n/a
----------------------------------------------------------------------------------More--
To display the sfe transmitter link information, use the show controller sfe link-info rx command in the System Admin EXEC mode.
show controller sfe link-info tx start-link-num end-link-num instance { asic-instance | all } location { node-id | all } [detail]
start-link-num |
Specifies the first value of a range of values. |
end-link-num |
Specifies the last value of a range of values. |
instance |
Indicates an ASIC instance. |
asic-instance |
Displays link information for a specific ASIC instance. Range is from 0 to 5. |
all |
Displays link information of all ASIC instances. |
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot notation. |
detail |
Displays detailed information. |
Brief information is displayed.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
The detail keyword displays the link history information. When the detail keyword is used, the Down Reason column in the example output indicates the reason why the link is down.
sysadmin-vm:0_RP0# show controller sfe link-info tx 0 1 instance 0 location 0/FC2 detail
Mon Aug 24 04:10:17.595 UTC
Mon Aug 24 04:10:17.622 UTC
---------------------------------------------------------------------------------
Node ID: 0_RP0 Instance: 0
Flags:
D - Power Down, I - Init/deinit, T - Invalid Topo, B - Bad link conn
E - Rcvr End Rst, F - No Far-end, C - CRC error, S - Size error
G - Code Grp err, M - Misalign, L - No Sig Lock, R - No Reachability Cells
---------------------------------------------------------------------------------
Link ID Oper Enable
Status Status
---------------------------------------------------------------------------------
0/FC2/0/0 UP UP
+-----------------------------------------------------------------------------+
| Timestamp Event(s) Down Reasons |
+-----------------------------------------------------------------------------+
2013 Aug 24 04:06:22.000 ADMIN_UP ERROR_NONE ............
2013 Aug 24 04:06:22.000 ADMIN_UP ERROR_NONE ............
2013 Aug 24 04:06:59.000 OPER_DN D...........
2013 Aug 24 04:06:59.000 OPER_UP ............
0/FC2/0/1 DN UP
+-----------------------------------------------------------------------------+
| Timestamp Event(s) Down Reasons |
+-----------------------------------------------------------------------------+
2013 Aug 24 04:06:22.000 ADMIN_UP ERROR_NONE ............
2013 Aug 24 04:06:22.000 ADMIN_UP ERROR_NONE ............
2013 Aug 24 04:06:59.000 OPER_DN D...........
To display the sfe (switch fabric element) statistics information, use the show controller sfe statistics command in the System Admin EXEC mode.
show controller sfe statistics block block-stats instance { asic-instance | all } location { node-id | all }
block block-stats |
|
instance |
Indicates an ASIC instance |
asic-instance |
Displays statistics for a specific ASIC. |
all |
Displays statistics for all asics or nodes. |
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot notation. |
None
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Displays block level statistics of SFE asics.
sysadmin-vm:0_RP0#show controller sfe statistics block CCS instance 0 location 0/FC0
Fri Jun 3 18:46:15.397 UTC
Device statistics:
============================================================
Node: 0/0, Instance: 0
============================================================
CCS statistics:
---------------------------------
CCS statistics:
---------------------------------
CCS0 UnreachableDestinationCellsCnt: 0
CCS1 UnreachableDestinationCellsCnt: 0
CCS0 CaptureFifoDiscardCnt: 0
CCS1 CaptureFifoDiscardCnt: 0
CCS0 CdmaLpCellsDiscardCnt: 0
CCS1 CdmaLpCellsDiscardCnt: 0
CCS0 CdmbLpCellsDiscardCnt: 0
CCS1 CdmbLpCellsDiscardCnt: 0
CCS0 CrpParityErrCnt: 0
CCS1 CrpParityErrCnt: 0
CCS0 Ecc1bErrCnt: 0
CCS1 Ecc1bErrCnt: 0
CCS0 Ecc2bErrCnt: 0
CCS1 Ecc2bErrCnt: 0
To display the sfe trace information, use the show controller fabric sfe trace command in the System Admin EXEC mode.
show controller sfe trace { all | trace-name } location node-id [ all | trace-attribute ]
trace-name |
Trace buffer name. |
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot notation. |
trace-attribute |
Trace attribute. |
all |
Displays all the details. |
None
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Use this command for diagnostics of SFE driver process functionality.
This example shows how to view the controller sfe trace information:
sysadmin-vm:0_RP0# show controller sfe trace all location 0/RP0
Fri Jun 3 18:42:52.440 UTC
----------------
01.53.28.885023744:...Hardware environment
01.53.29.166642432:mc_phys_addr 0x00000000f8000000
01.53.29.223421440: @msc_entity id="0/23783" display_name="sfe"
01.53.29.233022976:@msc_event entity_id="0/23783/23783" time="1307066009233023250" label="connecting to pm_lib with endpoint (0x0, 2020) (hdl=0x0x2e2f690)" type="Connection" completed="false" @msc_source pairing_id="0/23783/con_0x2e2f690" type="Lane"
01.53.29.242850816:CIPC:CONN (hdl=0x2e2fae0):cipc_connect():invoked on endpoint (0.0.0.0, 2020)
01.53.29.243809792:[PL]: sfe_platform_local_client_init called...
01.53.29.250015744: @msc_entity id="0/23783" display_name="sfe"
01.53.29.250038016:@msc_event entity_id="0/23783/23783" time="1307066009250038380" label="requesting connection to platform_local (CAPI hdl=0x2e4ae50, CIPC hdl = 0x2e4b690)" type="Connection" completed="false"
01.53.29.250231296:DS handle 0x2e4ae50 instantiated for platform_local client handle
01.53.29.251497984: @msc_entity id="0/23783" display_name="sfe"
01.53.29.260870912:@msc_event entity_id="0/23783/23783" time="1307066009260871320"
label="requesting connection to calvados_ds (CAPI hdl=0x2e6f570, CIPC hdl = 0x2e6f9a0)"
type="Connection" completed="false"
01.53.29.261379584:@msc_event entity_id="0/23783/23783" time="1307066009261380000"
label="connecting to calvados_ds with endpoint (0x7f000001, 7400) (hdl=0x0x2e6f570)"
type="Connection" completed="false" @msc_source pairing_id="0/23783/con_0x2e6f570" type="Lane"
01.53.29.268652800:CIPC:CONN (hdl=0x2e6f9a0):cipc_connect():invoked on endpoint (127.0.0.1, 7400)
01.53.29.268868096:CIPC:INFO (hdl=0x2e6f9a0):socket_connect():async socket connection in progress
01.53.29.268911360:[PL]: SFE driver request to setup a CAPI connection to PLFM.
01.53.29.273885696: @msc_entity id="0/23783" display_name="sfe"
01.53.29.273908480:@msc_event entity_id="0/23783/23783" time="1307066009273908810"
label="requesting connection to ccc_driver (CAPI hdl=0x2e81d80, CIPC hdl = 0x2e87ed0)"
type="Connection" completed="false"
01.53.29.273959168:DS handle 0x2e81d80 instantiated for ccc_driver client handle
01.53.29.274033152: @msc_entity id="0/23783" display_name="sfe"
01.53.29.281644288:@msc_event entity_id="0/23783/23783" time="1307066009281644580"
label="requesting connection to calvados_ds (CAPI hdl=0x2eaa780, CIPC hdl = 0x2eaabb0)"
type="Connection" completed="false"
01.53.29.281968640:@msc_event entity_id="0/23783/23783" time="1307066009281968850"
label="connecting to calvados_ds with endpoint (0x7f000001, 7400) (hdl=0x0x2eaa780)"
type="Connection" completed="false" @msc_source pairing_id="0/23783/con_0x2eaa780" type="Lane"
01.53.29.282761472:CIPC:CONN (hdl=0x2eaabb0):cipc_connect():invoked on endpoint (127.0.0.1, 7400)
01.53.29.282938112:CIPC:INFO (hdl=0x2eaabb0):socket_connect():async socket
To display information about the operations done on a slice by slice manager proxy, use the show controller slice command in System Admin EXEC or XR EXEC mode.
System Admin EXEC Mode show controllers slice [ all | <slice_number> ] reset-history [ summary | detail ] [ location [node-id] ]
XR EXEC Mode show controllers
all<slice_number> |
Enter the specific slice number or all the slices for which the information is to be displayed. The slice number value ranges from 0 to 4. |
reset-history [summary | detail] |
Provides information about the reset history of the slice. The summary and detail options provides a brief output. |
location [node-id] |
Identifies the node you want to shut down. The node-id argument is expressed in the rack or slot notation. |
Status and information are displayed for all nodes in the system.
System Admin EXEC
XR EXEC
Release |
Modification |
---|---|
Release 5.2.3 |
This command was introduced. |
RP/0/RP0/CPU0:router# show controller slice 0 reset-history summary location 0/2
Fri Oct 17 05:40:27.318 UTC
Â
======================================================================
Slice Manager Slice Context: 0
=========================================================================
| Timestamp | Prev State | Event | Next State |
=========================================================================
|2014 Oct 17 05:19:08.127| UNKNOWN | CFG SLICE | PWR DOWN WAIT |
|2014 Oct 17 05:19:09.679| PWR DOWN WAIT | PWR DWN SUCESS | PWR UP |
|2014 Oct 17 05:19:29.56 | PWR UP | PWR UP SUCESS | PWR UP DONE |
|2014 Oct 17 05:23:39.327| PWR UP DONE | CFG SLICE | PWR DOWN WAIT |
|2014 Oct 17 05:23:52.921| PWR DOWN WAIT | PWR DWN SUCESS | PWR UP |
|2014 Oct 17 05:24:13.637| PWR UP | PWR UP SUCESS | PWR UP DONE |
To display information about a specific slice controller FPGA and the slices controlled by the FPGA on the node, use the show controller slice_control FPGA command in the System Admin EXEC mode.
show controller slice_control FPGA { all | fpga-number } { { clocking-devices { all | device-number } | context-info | slice { all | slice-number } slice-attributes } location { all | node-id } | location { all | node-id } }
fpga-number |
FPGA number. Range is from 0 to 1. |
clocking-devices |
Displays the clocking device information. |
device-number |
Device number. |
context-info |
Displays the slice controller context information. |
slice |
Displays slice information. |
slice-number |
Slice number. Range is from 0 to 2. |
slice-attributes |
Slice attribute. |
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot notation. |
all |
Displays all the information. |
None
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Use this command to display all the software and hardware information for the slice FPGA, and the devices that are connected to the slice FPGA, such as clocking chips, PHYs, optics, and sensors. If an FPGA number is stated in the command, then the information related to that specific FPGA is displayed. If all keyword is used, then information for all the FPGAs is displayed.
sysadmin-vm:0_RP0#show controller slice_control FPGA 0 location 0/0
Tue Apr 14 16:20:30.867 UTC
Tue Apr 14 16:20:30.908 UTC
Tue Apr 14 16:20:30 UTC 1970
Tue Apr 14 16:20:30.943 UTC
FPGA id: 0
----------------------------------
Slice controller context information:
----------------------------------------
Controller id :0
Num Slices :2
Oper State :1
Hotplug Status :1
Hotplug Desc :0xa95ae0
PCI Handle :0xc40590
PCI Irq_Desc :0xa8e4a0
PCI MSI :104
PCI Base_Address :0x0
PCI Bus :103
PCI Device :0
PCI Virt_Address :0x7f5fa7cad000
Num PLL :4
c_hd :0x6d98d0
d_hd :0x6d98d0
i_hd :0x6d98d0
fm_hdl :(nil)
trace :0x95e320
levm :0x95c1e0
Clocking device information :
PLL device : 0
==================================================================
pll_id bus mode dev_addr i2c_regs
==================================================================
0 I2C_COMMON LAN 0x68 0x7f5fa7cad040
1 I2C_COMMON LAN 0x69 0x7f5fa7cad040
2 I2C_COMMON LAN 0x6a 0x7f5fa7cad040
3 I2C_COMMON LAN 0x6b 0x7f5fa7cad040
==================================================================
Slice id: 0
------------------------
Slice summary info:
==============================================================
slice num num num num temp num volt num curr
id phy optics eeprom sensors sensors sensors
==============================================================
0 4 2 1 3 16 8
Current sensor information:
-------------------------------
curr_sensor id :0
sensor id :LTC4151_VP1P0_SRDS
dev addr :17224
poll intvl :10
delta :5
raw data :425
sensor value :340
unit :3
last value :336
send update :false
num 1sec_intervals :2
curr_sensor id :1
sensor id :LTC4151_VP1P5
dev addr :17248
poll intvl :10
delta :5
raw data :978
sensor value :2608
unit :3
last value :2610
send update :false
num 1sec_intervals :2
curr_sensor id :2
sensor id :UNKNOWN
dev addr :17200
poll intvl :10
delta :5
raw data :947
sensor value :757
unit :3
last value :756
send update :false
num 1sec_intervals :3
curr_sensor id :3
sensor id :LTC4151_VP0P9_AVS
dev addr :17164
poll intvl :10
delta :5
raw data :1570
sensor value :2512
unit :3
last value :2508
send update :false
num 1sec_intervals :3
curr_sensor id :4
sensor id :LTC4151_VP0P9_PITA
dev addr :17188
poll intvl :10
delta :5
raw data :69
sensor value :55
unit :3
last value :52
send update :false
num 1sec_intervals :3
curr_sensor id :5
sensor id :LTC4151_VP1P0_AMBA
dev addr :17212
poll intvl :10
delta :5
raw data :796
sensor value :1273
unit :3
last value :1272
send update :false
num 1sec_intervals :3
curr_sensor id :6
sensor id :LTC4151_VP1P0_AMBA_B
dev addr :17236
poll intvl :10
delta :5
raw data :667
sensor value :533
unit :3
last value :532
send update :false
num 1sec_intervals :3
curr_sensor id :7
sensor id :LTC4151_VP0P9_AVS_B
dev addr :17176
poll intvl :10
delta :5
raw data :1580
sensor value :2528
unit :3
last value :2528
send update :false
num 1sec_intervals :3
======================================================================
eeprom_id type bus i2c_regs
======================================================================
0 SLICE_EEPROM_GENNUM SLICE_I2C_SHARED 0x7f5fa7cb1000
======================================================================
optics_id type bus i2c_regs
======================================================================
0 CXP SLICE_I2C_OPTICS_0 0x7f5fa7cb0000
1 CXP SLICE_I2C_OPTICS_1 0x7f5fa7cb0200
Optics id : 0
---------------------------
CXP information :
port_id :0
signature :0x43585020444c4c00
cxp_port_ready :true
opaque :0x6da260
nodeid :0xa23a40
slice :1
capabilities :0x28aabaa34f9ff
vendor_name :CISCO-AVAGO
vendor_part_num :
vendor_rev_num :01
vendor_serial_num :AGF155220WD
passive :false
STATUS FLAGS
D - Channel Disabled
O - Channel Output Disabled
L - LOS Disabled
F - Fault Disabled
B - Bias Current Alarm Disabled
P - Power Alarm Disabled
T - Temperature Alarm Disabled
V - Vcc Alarm Disabled
ERROR FLAGS
L - LOS Alarm
F - Fault
B - High Bias Current b - low Bias Current
P - High Power Alarm p - Low Power Alarm
T - High Temperature Alarm t - Low Temperature Alarm
V - High Vcc Alarm v - Low Vcc Alarm
==========================================================
Channel Status_Flag Error_Flag
==========================================================
0 D----- L---
1 D----- ----
2 D----- ----
3 D----- ----
4 D----- ----
5 D----- ----
6 D----- ----
7 D----- ----
8 D----- ----
9 D----- ----
10 D----- ----
11 D----- L---
STATUS FLAGS
D - Channel Disabled
O - Channel Output Disabled
L - LOS Disabled
F - Fault Disabled
B - Bias Current Alarm Disabled
P - Power Alarm Disabled
T - Temperature Alarm Disabled
V - Vcc Alarm Disabled
ERROR FLAGS
L - LOS Alarm
F - Fault
B - High Bias Current b - low Bias Current
P - High Power Alarm p - Low Power Alarm
T - High Temperature Alarm t - Low Temperature Alarm
V - High Vcc Alarm v - Low Vcc Alarm
==========================================================
Channel Status Error
==========================================================
0 D----- L--p
1 ------ L--p
2 ------ ----
3 ------ L--p
4 ------ ---p
5 ------ L--p
6 ------ L--p
7 ------ ---p
8 ------ L---
9 ------ ---p
10 ------ L---
11 D----- ---p
=========================================
Tx Channel Equalization
=========================================
0 0x00
1 0x00
2 0x00
3 0x00
4 0x00
5 0x00
6 0x00
7 0x00
8 0x00
9 0x00
10 0x00
11 0x00
==============================================================
Rx Channel Amplitude De_Emphasis
==============================================================
0 0x03 0x00
1 0x03 0x00
2 0x03 0x00
3 0x03 0x00
4 0x03 0x00
5 0x03 0x00
6 0x03 0x00
7 0x03 0x00
8 0x03 0x00
9 0x03 0x00
10 0x03 0x00
11 0x03 0x00
Optics id : 1
---------------------------
CXP information :
port_id :1
signature :0x43585020444c4c00
cxp_port_ready :true
opaque :0x6da490
nodeid :0xa23a40
slice :1
capabilities :0x28aabaa34f9ff
vendor_name :CISCO-AVAGO
vendor_part_num :10-2790-01
vendor_rev_num :01
vendor_serial_num :AGF162920JA
passive :false
STATUS FLAGS
D - Channel Disabled
O - Channel Output Disabled
L - LOS Disabled
F - Fault Disabled
B - Bias Current Alarm Disabled
P - Power Alarm Disabled
T - Temperature Alarm Disabled
V - Vcc Alarm Disabled
ERROR FLAGS
L - LOS Alarm
F - Fault
B - High Bias Current b - low Bias Current
P - High Power Alarm p - Low Power Alarm
T - High Temperature Alarm t - Low Temperature Alarm
V - High Vcc Alarm v - Low Vcc Alarm
==========================================================
Channel Status_Flag Error_Flag
==========================================================
0 D----- L---
1 D----- ----
2 D----- ----
3 D----- ----
4 D----- ----
5 D----- ----
6 D----- ----
7 D----- ----
8 D----- ----
9 D----- ----
10 D----- ----
11 D----- L---
STATUS FLAGS
D - Channel Disabled
O - Channel Output Disabled
L - LOS Disabled
F - Fault Disabled
B - Bias Current Alarm Disabled
P - Power Alarm Disabled
T - Temperature Alarm Disabled
V - Vcc Alarm Disabled
ERROR FLAGS
L - LOS Alarm
F - Fault
B - High Bias Current b - low Bias Current
P - High Power Alarm p - Low Power Alarm
T - High Temperature Alarm t - Low Temperature Alarm
V - High Vcc Alarm v - Low Vcc Alarm
==========================================================
Channel Status Error
==========================================================
0 D----- L--p
1 ------ L--p
2 ------ L---
3 ------ ---p
4 ------ L---
5 ------ L--p
6 ------ L--p
7 ------ L---
8 ------ L--p
9 ------ ---p
10 ------ L---
11 D----- ---p
=========================================
Tx Channel Equalization
=========================================
0 0x00
1 0x00
2 0x00
3 0x00
4 0x00
5 0x00
6 0x00
7 0x00
8 0x00
9 0x00
10 0x00
11 0x00
==============================================================
Rx Channel Amplitude De_Emphasis
==============================================================
0 0x03 0x00
1 0x03 0x00
2 0x03 0x00
3 0x03 0x00
4 0x03 0x00
5 0x03 0x00
6 0x03 0x00
7 0x03 0x00
8 0x03 0x00
9 0x03 0x00
10 0x03 0x00
11 0x03 0x00
======================================================================
phy_id type bus i2c_regs
======================================================================
0 GENNUM SLICE_I2C_SHARED 0x7f5fa7cb1000
1 GENNUM SLICE_I2C_SHARED 0x7f5fa7cb1000
2 GENNUM SLICE_I2C_SHARED 0x7f5fa7cb1000
3 GENNUM SLICE_I2C_SHARED 0x7f5fa7cb1000
Temperature sensor information:
-----------------------------------
temp_sensor id :0
sensor id :TMP421_PITA_DIE_REMOTE
dev addr :17668
poll intvl :10
delta :1
raw data :1174
sensor value :73
unit :6
last value :73
send update :false
num 1sec_intervals :1
temp_sensor id :1
sensor id :TMP421_AMBA_DIE_LOCAL
dev addr :17672
poll intvl :10
delta :1
raw data :875
sensor value :54
unit :6
last value :54
send update :false
num 1sec_intervals :1
temp_sensor id :2
sensor id :TMP421_AMBA_DIE_REMOTE
dev addr :17676
poll intvl :10
delta :1
raw data :827
sensor value :51
unit :6
last value :51
send update :false
num 1sec_intervals :1
Voltage sensor information:
-------------------------------
volt_sensor id :0
sensor id :LTC2978_VP0P9_AVS
dev addr :8960
poll intvl :10
delta :16
raw data :7781
sensor value :949
unit :2
last value :949
send update :false
num 1sec_intervals :1
volt_sensor id :1
sensor id :LTC2978_VP1P5
dev addr :8968
poll intvl :10
delta :27
raw data :12286
sensor value :1499
unit :2
last value :1500
send update :false
num 1sec_intervals :2
volt_sensor id :2
sensor id :LTC2978_VP1P8
dev addr :8976
poll intvl :10
--More--0/RP0:Apr 14 16:21:25.384 : pm[1741]: %INFRA-Process_Manager-3-PROCESS_RESTART : Process ael_mgbl restarted
delta :16
raw data :14747
sensor value :1800
unit :2
last value :1800
send update :false
num 1sec_intervals :2
volt_sensor id :3
sensor id :LTC2978_VP0P9
dev addr :8984
poll intvl :10
delta :16
raw data :7127
sensor value :869
unit :2
last value :869
send update :false
num 1sec_intervals :7
volt_sensor id :4
sensor id :LTC2978_VP1P0_PITA
dev addr :8992
poll intvl :10
delta :18
raw data :8191
sensor value :999
unit :2
last value :1000
send update :false
num 1sec_intervals :7
volt_sensor id :5
sensor id :LTC2978_VP0P9_PITA
dev addr :9000
poll intvl :10
delta :16
raw data :7374
sensor value :900
unit :2
last value :900
send update :false
num 1sec_intervals :7
volt_sensor id :6
sensor id :LTC2978_VP1P0_SRDS
dev addr :9008
poll intvl :10
delta :18
raw data :8193
sensor value :1000
unit :2
last value :999
send update :false
num 1sec_intervals :7
volt_sensor id :7
sensor id :LTC2978_VP1P0_AMBA
dev addr :9016
poll intvl :10
delta :18
raw data :8191
sensor value :999
unit :2
last value :999
send update :false
num 1sec_intervals :7
volt_sensor id :8
sensor id :LTC4151_VP1P0_SRDS
dev addr :17228
poll intvl :10
delta :185
raw data :430
sensor value :10750
unit :2
last value :10875
send update :false
num 1sec_intervals :7
volt_sensor id :9
sensor id :LTC4151_VP1P5
dev addr :17252
poll intvl :10
delta :185
raw data :430
sensor value :10750
unit :2
last value :10850
send update :false
num 1sec_intervals :7
volt_sensor id :10
sensor id :UNKNOWN
dev addr :17204
poll intvl :10
delta :185
raw data :436
sensor value :10900
unit :2
last value :11000
send update :false
num 1sec_intervals :8
volt_sensor id :11
sensor id :LTC4151_VP0P9_AVS
dev addr :17168
poll intvl :10
delta :185
raw data :430
sensor value :10750
unit :2
last value :10875
send update :false
num 1sec_intervals :8
volt_sensor id :12
sensor id :LTC4151_VP0P9_PITA
dev addr :17192
poll intvl :10
delta :185
raw data :435
sensor value :10875
unit :2
last value :10975
send update :false
num 1sec_intervals :8
volt_sensor id :13
sensor id :LTC4151_VP1P0_AMBA
dev addr :17216
poll intvl :10
delta :185
raw data :431
sensor value :10775
unit :2
last value :10900
send update :false
num 1sec_intervals :8
volt_sensor id :14
sensor id :LTC4151_VP1P0_AMBA_B
dev addr :17240
poll intvl :10
delta :185
raw data :431
sensor value :10775
unit :2
last value :10900
send update :false
num 1sec_intervals :8
volt_sensor id :15
sensor id :LTC4151_VP0P9_AVS_B
dev addr :17180
poll intvl :10
delta :185
raw data :431
sensor value :10775
unit :2
last value :10900
send update :false
num 1sec_intervals :8
To display the slice control context information, use the show controller slice_control context-info command in the System Admin EXEC mode.
show controller slice_control context-info location { all | node-id }
location node-id |
Selects the target location. The node-id argument is expressed in the rack/slot notation. |
all |
Displays information from all the nodes. |
None
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
This command displays the software context and information for the slice FPGA.
sysadmin-vm:0_RP0#show controller slice_control context-info location 0/3
Mon Aug 12 17:54:20.121 UTC
Mon Aug 12 17:54:20.148 UTC
Mon Aug 12 17:54:20 UTC 2013
Mon Aug 12 17:54:20.175 UTC
Slice manager context information:
----------------------------------------
num controllers :1
levm :0x265d1e0
ccc_hdl :0x2752910
trace :0x265f320
xml_hdl :0x2838de0
fm_hdl :0x2837b80
sim :false
debug :false
card_type :5507172
slot_num :19
To display all the information related to the slice control FPGAs, slice hardware, optics, clocking devices, PHYs, and sensors on a card, use the show controller slice_control location command in the System Admin EXEC mode.
show controller slice_control location { all | node-id }
node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot notation. |
all |
Displays information from all the nodes. |
None
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Use this command to display all the software and hardware information for the slice FPGA, and the devices that are connected to the slice FPGA, such as clocking chips, PHYs, optics, and sensors.
sysadmin-vm:0_RP0#show controller slice_control location 0/0
Fri Aug 30 20:08:24.778 UTC
Fri Aug 30 20:08:24.810 UTC
Fri Aug 30 16:08:24 EDT 2013
Fri Aug 30 20:08:24.838 UTC
Slice controller node : 0/0
===========================================
Slice manager context information:
----------------------------------------
num controllers :1
levm :0x21be1e0
ccc_hdl :0x22b3890
trace :0x21c0320
xml_hdl :0x2394f70
fm_hdl :0x2393d10
sim :false
debug :false
card_type :5507173
slot_num :16
FPGA id: 0
----------------------------------
Slice controller context information:
----------------------------------------
Controller id :0
Num Slices :2
Oper State :1
Hotplug Status :1
Hotplug Desc :0x22f7a60
PCI Handle :0x22f1110
PCI Irq_Desc :0x22f0420
PCI MSI :103
PCI Base_Address :0x0
PCI Bus :103
PCI Device :0
PCI Virt_Address :0x7f1175ebf000
Num PLL :4
c_hd :0x6d8bb0
d_hd :0x6d8bb0
i_hd :0x6d8bb0
fm_hdl :(nil)
trace :0x21c0320
levm :0x21be1e0
Clocking device information :
PLL device : 0
==================================================================
pll_id bus mode dev_addr i2c_regs
==================================================================
0 I2C_COMMON LAN 0x68 0x7f1175ebf040
1 I2C_COMMON LAN 0x69 0x7f1175ebf040
2 I2C_COMMON LAN 0x6a 0x7f1175ebf040
3 I2C_COMMON LAN 0x6b 0x7f1175ebf040
==================================================================
Slice id: 0
------------------------
Slice summary info:
==============================================================
slice num num num num temp num volt num curr
id phy optics eeprom sensors sensors sensors
==============================================================
0 4 2 1 3 16 8
Current sensor information:
-------------------------------
curr_sensor id :0
sensor id :LTC4151_VP1P0_SRDS
dev addr :17224
poll intvl :10
delta :5
raw data :1350
sensor value :1080
unit :3
last value :1080
send update :false
num 1sec_intervals :2
curr_sensor id :1
sensor id :LTC4151_VP1P5
dev addr :17248
poll intvl :10
delta :5
raw data :949
sensor value :2530
unit :3
last value :2530
send update :false
num 1sec_intervals :2
curr_sensor id :2
sensor id :UNKNOWN
dev addr :17200
poll intvl :10
delta :5
raw data :919
sensor value :735
unit :3
last value :734
send update :false
num 1sec_intervals :2
curr_sensor id :3
sensor id :LTC4151_VP0P9_AVS
dev addr :17164
poll intvl :10
delta :5
raw data :1356
sensor value :2169
unit :3
last value :2172
send update :false
num 1sec_intervals :2
curr_sensor id :4
sensor id :LTC4151_VP0P9_PITA
dev addr :17188
poll intvl :10
delta :5
raw data :55
sensor value :44
unit :3
last value :41
send update :false
num 1sec_intervals :2
curr_sensor id :5
sensor id :LTC4151_VP1P0_AMBA
dev addr :17212
poll intvl :10
delta :5
raw data :819
sensor value :1310
unit :3
last value :1307
send update :false
num 1sec_intervals :2
curr_sensor id :6
sensor id :LTC4151_VP1P0_AMBA_B
dev addr :17236
poll intvl :10
delta :5
raw data :826
sensor value :660
unit :3
last value :661
send update :false
num 1sec_intervals :2
curr_sensor id :7
sensor id :LTC4151_VP0P9_AVS_B
dev addr :17176
poll intvl :10
delta :5
raw data :1307
sensor value :2091
unit :3
last value :2089
send update :false
num 1sec_intervals :3
======================================================================
eeprom_id type bus i2c_regs
======================================================================
0 SLICE_EEPROM_GENNUM SLICE_I2C_SHARED 0x7f1175ec3000
======================================================================
optics_id type bus i2c_regs
======================================================================
0 CXP SLICE_I2C_OPTICS_0 0x7f1175ec2000
1 CXP SLICE_I2C_OPTICS_1 0x7f1175ec2200
Optics id : 0
---------------------------
CXP information :
port_id :0
signature :0x43585020444c4c00
cxp_port_ready :true
opaque :0x6d9540
nodeid :0x2286740
slice :1
capabilities :0x28aabaa34f9ff
vendor_name :CISCO-AVAGO
vendor_part_num :10-2790-01
vendor_rev_num :01
vendor_serial_num :AGF1632203T
passive :false
STATUS FLAGS
D - Channel Disabled
O - Channel Output Disabled
L - LOS Disabled
F - Fault Disabled
B - Bias Current Alarm Disabled
P - Power Alarm Disabled
T - Temperature Alarm Disabled
V - Vcc Alarm Disabled
ERROR FLAGS
L - LOS Alarm
F - Fault
B - High Bias Current b - low Bias Current
P - High Power Alarm p - Low Power Alarm
T - High Temperature Alarm t - Low Temperature Alarm
V - High Vcc Alarm v - Low Vcc Alarm
==========================================================
Channel Status_Flag Error_Flag
==========================================================
0 D----- L---
1 ------ ----
2 ------ ----
3 ------ ----
4 ------ ----
5 ------ ----
6 ------ ----
7 ------ ----
8 ------ ----
9 ------ ----
10 ------ ----
11 D----- ----
STATUS FLAGS
D - Channel Disabled
O - Channel Output Disabled
L - LOS Disabled
F - Fault Disabled
B - Bias Current Alarm Disabled
P - Power Alarm Disabled
T - Temperature Alarm Disabled
V - Vcc Alarm Disabled
ERROR FLAGS
L - LOS Alarm
F - Fault
B - High Bias Current b - low Bias Current
P - High Power Alarm p - Low Power Alarm
T - High Temperature Alarm t - Low Temperature Alarm
V - High Vcc Alarm v - Low Vcc Alarm
==========================================================
Channel Status Error
==========================================================
0 D----- L--p
1 ------ ----
2 ------ ----
3 ------ ----
4 ------ ----
5 ------ ----
6 ------ ----
7 ------ ----
8 ------ ----
9 ------ ----
10 ------ ----
11 D----- ---p
=========================================
Tx Channel Equalization
=========================================
0 0x00
1 0x00
2 0x00
3 0x00
4 0x00
5 0x00
6 0x00
7 0x00
8 0x00
9 0x00
10 0x00
11 0x00
==============================================================
Rx Channel Amplitude De_Emphasis
==============================================================
0 0x03 0x00
1 0x03 0x00
2 0x03 0x00
3 0x03 0x00
4 0x03 0x00
5 0x03 0x00
6 0x03 0x00
7 0x03 0x00
8 0x03 0x00
9 0x03 0x00
10 0x03 0x00
11 0x03 0x00
Optics id : 1
---------------------------
CXP information :
port_id :1
No valid data.
STATUS FLAGS
D - Channel Disabled
O - Channel Output Disabled
L - LOS Disabled
F - Fault Disabled
B - Bias Current Alarm Disabled
P - Power Alarm Disabled
T - Temperature Alarm Disabled
V - Vcc Alarm Disabled
ERROR FLAGS
L - LOS Alarm
F - Fault
B - High Bias Current b - low Bias Current
P - High Power Alarm p - Low Power Alarm
T - High Temperature Alarm t - Low Temperature Alarm
V - High Vcc Alarm v - Low Vcc Alarm
==========================================================
Channel Status_Flag Error_Flag
==========================================================
0 No valid data.
1 No valid data.
2 No valid data.
3 No valid data.
4 No valid data.
5 No valid data.
6 No valid data.
7 No valid data.
8 No valid data.
9 No valid data.
10 No valid data.
11 No valid data.
STATUS FLAGS
D - Channel Disabled
O - Channel Output Disabled
L - LOS Disabled
F - Fault Disabled
B - Bias Current Alarm Disabled
P - Power Alarm Disabled
T - Temperature Alarm Disabled
V - Vcc Alarm Disabled
ERROR FLAGS
L - LOS Alarm
F - Fault
B - High Bias Current b - low Bias Current
P - High Power Alarm p - Low Power Alarm
T - High Temperature Alarm t - Low Temperature Alarm
V - High Vcc Alarm v - Low Vcc Alarm
==========================================================
Channel Status Error
==========================================================
0 No valid data.
1 No valid data.
2 No valid data.
3 No valid data.
4 No valid data.
5 No valid data.
6 No valid data.
7 No valid data.
8 No valid data.
9 No valid data.
10 No valid data.
11 No valid data.
=========================================
Tx Channel Equalization
=========================================
0 No valid data.
1 No valid data.
2 No valid data.
3 No valid data.
4 No valid data.
5 No valid data.
6 No valid data.
7 No valid data.
8 No valid data.
9 No valid data.
10 No valid data.
11 No valid data.
==============================================================
Rx Channel Amplitude De_Emphasis
==============================================================
0 No valid data.
1 No valid data.
2 No valid data.
3 No valid data.
4 No valid data.
5 No valid data.
6 No valid data.
7 No valid data.
8 No valid data.
9 No valid data.
10 No valid data.
11 No valid data.
======================================================================
phy_id type bus i2c_regs
======================================================================
0 GENNUM SLICE_I2C_SHARED 0x7f1175ec3000
1 GENNUM SLICE_I2C_SHARED 0x7f1175ec3000
2 GENNUM SLICE_I2C_SHARED 0x7f1175ec3000
3 GENNUM SLICE_I2C_SHARED 0x7f1175ec3000
Temperature sensor information:
-----------------------------------
temp_sensor id :0
sensor id :TMP421_PITA_DIE_REMOTE
dev addr :17668
poll intvl :10
delta :1
raw data :761
sensor value :47
unit :6
last value :47
send update :false
num 1sec_intervals :5
temp_sensor id :1
sensor id :TMP421_AMBA_DIE_LOCAL
dev addr :17672
poll intvl :10
delta :1
raw data :601
sensor value :37
unit :6
last value :37
send update :false
num 1sec_intervals :5
temp_sensor id :2
sensor id :TMP421_AMBA_DIE_REMOTE
dev addr :17676
poll intvl :10
delta :1
raw data :671
sensor value :41
unit :6
last value :41
send update :false
num 1sec_intervals :5
Voltage sensor information:
-------------------------------
volt_sensor id :0
sensor id :LTC2978_VP0P9_AVS
dev addr :8960
poll intvl :10
delta :16
raw data :7783
sensor value :950
unit :2
last value :950
send update :false
num 1sec_intervals :5
volt_sensor id :1
sensor id :LTC2978_VP1P5
dev addr :8968
poll intvl :10
delta :27
raw data :12288
sensor value :1500
unit :2
last value :1500
send update :false
num 1sec_intervals :5
volt_sensor id :2
sensor id :LTC2978_VP1P8
dev addr :8976
poll intvl :10
delta :16
raw data :14743
sensor value :1799
unit :2
last value :1800
send update :false
num 1sec_intervals :5
volt_sensor id :3
sensor id :LTC2978_VP0P9
dev addr :8984
poll intvl :10
delta :16
raw data :7126
sensor value :869
unit :2
last value :870
send update :false
num 1sec_intervals :5
volt_sensor id :4
sensor id :LTC2978_VP1P0_PITA
dev addr :8992
poll intvl :10
delta :18
raw data :8192
sensor value :1000
unit :2
last value :999
send update :false
num 1sec_intervals :5
volt_sensor id :5
sensor id :LTC2978_VP0P9_PITA
dev addr :9000
poll intvl :10
delta :16
raw data :7372
sensor value :899
unit :2
last value :899
send update :false
num 1sec_intervals :5
volt_sensor id :6
sensor id :LTC2978_VP1P0_SRDS
dev addr :9008
poll intvl :10
delta :18
raw data :8192
sensor value :1000
unit :2
last value :999
send update :false
num 1sec_intervals :5
volt_sensor id :7
sensor id :LTC2978_VP1P0_AMBA
dev addr :9016
poll intvl :10
delta :18
raw data :8193
sensor value :1000
unit :2
last value :1000
send update :false
num 1sec_intervals :6
volt_sensor id :8
sensor id :LTC4151_VP1P0_SRDS
dev addr :17228
poll intvl :10
delta :185
raw data :435
sensor value :10875
unit :2
last value :10850
send update :false
num 1sec_intervals :6
volt_sensor id :9
sensor id :LTC4151_VP1P5
dev addr :17252
poll intvl :10
delta :185
raw data :434
sensor value :10850
unit :2
last value :10825
send update :false
num 1sec_intervals :6
volt_sensor id :10
sensor id :UNKNOWN
dev addr :17204
poll intvl :10
delta :185
raw data :445
sensor value :11125
unit :2
last value :11175
send update :false
num 1sec_intervals :6
volt_sensor id :11
sensor id :LTC4151_VP0P9_AVS
dev addr :17168
poll intvl :10
delta :185
raw data :433
sensor value :10825
unit :2
last value :10800
send update :false
num 1sec_intervals :6
volt_sensor id :12
sensor id :LTC4151_VP0P9_PITA
dev addr :17192
poll intvl :10
delta :185
raw data :445
sensor value :11125
unit :2
last value :11200
send update :false
num 1sec_intervals :6
volt_sensor id :13
sensor id :LTC4151_VP1P0_AMBA
dev addr :17216
poll intvl :10
delta :185
raw data :433
sensor value :10825
unit :2
last value :11000
send update :false
num 1sec_intervals :6
volt_sensor id :14
sensor id :LTC4151_VP1P0_AMBA_B
dev addr :17240
poll intvl :10
delta :185
raw data :434
sensor value :10850
unit :2
last value :10825
send update :false
num 1sec_intervals :6
volt_sensor id :15
sensor id :LTC4151_VP0P9_AVS_B
dev addr :17180
poll intvl :10
delta :185
raw data :435
sensor value :10875
unit :2
last value :11025
send update :false
num 1sec_intervals :7
To display various FDB (forwarding database) details based on MAC address filters, source port filters, and VLAN, use the show controller switch fdb command in the System Admin EXEC mode. This command can also be used to view the location and statistics of the FDB.
show controller switch fdb [ location [node-id] | [ mac mac-address | port port-number | statistics | vlan vlan-id ] [ location [node-id] ] ]
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot/switch notation. |
mac mac-address |
Displays the switch FDB information based on the MAC address. |
port port-number |
Displays the switch FDB information based on the source port filter. |
statistics |
Displays the FDB statistics. |
vlan vlan-id |
Displays the switch FDB information based on the VLAN filter. |
Displays statistics summary for each node.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Detailed information for a specific node is displayed if the location node-id keyword is specified.
This example shows how to display switch FDB information without any keyword:
sysadmin-vm:0_RP0# show controller switch fdb
Fri Aug 30 20:29:52.855 UTC
FDB Maintenance Counters For Switch 0/RP0/RP-SW
Current shadow table entries: 127
Maximum shadow table entries: 198
Maximum hash chain depth: 1
Number of entries added: 2318
Number of entries deleted: 2191
Number of entries updated: 0
Number of FDB flushes: 1
Address update messages: 2191
New addresses: 2314
Aged addresses: 2191
Transplanted updates: 0
Forwarding updates: 0
Address insert errors: 0
Address update errors: 0
FDB memory errors: 0
FDB allocation errors: 0
Address updates queued: 0
Address queue full: No
Forwarding updates queued: 0
Forwarding queue full: No
FDB Table Synchronization Information
FDB Instance Total Entries Static Entries
---------------------------------------------
0 127 4
1 127 4
2 127 4
3 127 4
Shadow 127 4
FDB Maintenance Counters For Switch 0/RP1/RP-SW
Current shadow table entries: 134
Maximum shadow table entries: 201
Maximum hash chain depth: 1
Number of entries added: 2325
Number of entries deleted: 2191
Number of entries updated: 0
Number of FDB flushes: 1
Address update messages: 2191
New addresses: 2321
Aged addresses: 2191
Transplanted updates: 0
Forwarding updates: 0
Address insert errors: 0
Address update errors: 0
FDB memory errors: 0
FDB allocation errors: 0
Address updates queued: 0
Address queue full: No
Forwarding updates queued: 0
Forwarding queue full: No
FDB Table Synchronization Information
FDB Instance Total Entries Static Entries
---------------------------------------------
0 134 4
1 134 4
2 134 4
3 134 4
Shadow 134 4
FDB Maintenance Counters For Switch 0/LC0/LC-SW
Current shadow table entries: 123
Maximum shadow table entries: 180
Maximum hash chain depth: 1
Number of entries added: 1167
Number of entries deleted: 1044
Number of entries updated: 0
Number of FDB flushes: 1
Address update messages: 1044
New addresses: 1165
Aged addresses: 1044
Transplanted updates: 0
Forwarding updates: 0
Address insert errors: 0
Address update errors: 0
FDB memory errors: 0
FDB allocation errors: 0
Address updates queued: 0
Address queue full: No
Forwarding updates queued: 0
Forwarding queue full: No
FDB Table Synchronization Information
FDB Instance Total Entries Static Entries
---------------------------------------------
0 123 2
1 123 2
Shadow 123 2
FDB Maintenance Counters For Switch 0/LC1/LC-SW
Current shadow table entries: 122
Maximum shadow table entries: 179
Maximum hash chain depth: 1
Number of entries added: 1169
Number of entries deleted: 1047
Number of entries updated: 0
Number of FDB flushes: 1
Address update messages: 1047
New addresses: 1167
Aged addresses: 1047
Transplanted updates: 0
Forwarding updates: 0
Address insert errors: 0
Address update errors: 0
FDB memory errors: 0
FDB allocation errors: 0
Address updates queued: 0
Address queue full: No
Forwarding updates queued: 0
Forwarding queue full: No
FDB Table Synchronization Information
FDB Instance Total Entries Static Entries
---------------------------------------------
0 122 2
1 122 2
Shadow 122 2
FDB Maintenance Counters For Switch 0/LC7/LC-SW
Current shadow table entries: 123
Maximum shadow table entries: 179
Maximum hash chain depth: 1
Number of entries added: 1180
Number of entries deleted: 1057
Number of entries updated: 0
Number of FDB flushes: 1
Address update messages: 1057
New addresses: 1178
Aged addresses: 1057
Transplanted updates: 0
Forwarding updates: 0
Address insert errors: 0
Address update errors: 0
FDB memory errors: 0
FDB allocation errors: 0
Address updates queued: 0
Address queue full: No
Forwarding updates queued: 0
Forwarding queue full: No
FDB Table Synchronization Information
FDB Instance Total Entries Static Entries
---------------------------------------------
0 123 2
1 123 2
Shadow 123 2
Rack Card Switch
------------------
0 RP0 RP-SW
FDB Src Synced
Index MAC Address VLAN Port Trap Static Cores
----------------------------------------------------------------------
200 e0:50:bf:1c:f1:05 2049 (0x801) 16 No No 0 1 2 3
396 00:b0:64:fd:51:68 513 (0x201) 36 No No 0 1 2 3
504 e0:52:2d:4c:bd:03 2049 (0x801) 0 No No 0 1 2 3
804 00:04:4d:d8:6a:c0 514 (0x202) 54 No No 0 1 2 3
960 00:50:54:80:a5:fb 513 (0x201) 36 No No 0 1 2 3
1724 e0:50:a0:bf:8c:00 2049 (0x801) 21 No No 0 1 2 3
1896 00:00:0c:07:ac:02 513 (0x201) 36 No No 0 1 2 3
1932 00:b0:64:fd:18:1c 513 (0x201) 36 No No 0 1 2 3
2092 00:10:7b:e8:09:f8 513 (0x201) 36 No No 0 1 2 3
2368 4c:4e:35:b6:48:ff 2049 (0x801) 40 No No 0 1 2 3
2512 4c:4e:35:b6:49:0e 513 (0x201) 40 No No 0 1 2 3
2513 4e:41:50:00:01:01 2050 (0x802) 18 No No 0 1 2 3
2756 00:04:4d:da:5b:40 513 (0x201) 36 No No 0 1 2 3
2984 00:13:80:31:74:80 513 (0x201) 36 No No 0 1 2 3
3636 00:12:44:d9:f0:c0 513 (0x201) 36 No No 0 1 2 3
3732 00:04:4d:da:3c:c0 513 (0x201) 36 No No 0 1 2 3
4244 00:00:0c:07:ac:5a 513 (0x201) 36 No No 0 1 2 3
4324 4e:41:50:00:07:01 2050 (0x802) 0 No No 0 1 2 3
4356 00:17:5a:af:71:58 513 (0x201) 36 No No 0 1 2 3
4568 b4:14:89:60:d8:80 513 (0x201) 36 No No 0 1 2 3
4648 00:00:0c:07:ac:28 513 (0x201) 36 No No 0 1 2 3
4772 00:00:0c:07:ac:32 513 (0x201) 36 No No 0 1 2 3
5000 e2:3b:4f:77:04:03 2049 (0x801) 18 No No 0 1 2 3
5296 00:04:4d:da:13:40 513 (0x201) 36 No No 0 1 2 3
5588 00:00:0c:07:ac:3c 514 (0x202) 54 No No 0 1 2 3
5624 e0:50:72:f4:dd:05 513 (0x201) 36 No No 0 1 2 3
5712 e2:3b:4d:f0:93:00 2049 (0x801) 26 No No 0 1 2 3
6092 00:04:4d:d8:4d:00 513 (0x201) 36 No No 0 1 2 3
6552 e2:3b:43:46:6c:00 2049 (0x801) 5 No No 0 1 2 3
6584 4e:41:50:00:00:12 2050 (0x802) 16 No No 0 1 2 3
6656 6c:9c:ed:79:92:90 513 (0x201) 36 No No 0 1 2 3
7572 4c:4e:35:b6:48:fb 2049 (0x801) - Yes Yes 0 1 2 3
8432 46:70:39:1b:79:00 513 (0x201) 40 No No 0 1 2 3
9048 88:43:e1:c2:b6:56 513 (0x201) 36 No No 0 1 2 3
9240 00:0d:65:50:f3:1c 514 (0x202) 54 No No 0 1 2 3
9356 00:04:4d:b2:47:00 514 (0x202) 54 No No 0 1 2 3
9432 e2:3b:4f:77:04:00 2049 (0x801) 18 No No 0 1 2 3
10596 00:b0:64:fd:56:14 513 (0x201) 36 No No 0 1 2 3
11648 78:2b:cb:1e:0a:b3 513 (0x201) 36 No No 0 1 2 3
12008 4e:41:50:00:00:11 2050 (0x802) 16 No No 0 1 2 3
12344 00:00:0c:07:ac:01 513 (0x201) 36 No No 0 1 2 3
12496 01:4d:4c:41:50:01 1025 (0x401) - Yes Yes 0 1 2 3
12772 64:00:f1:42:09:12 514 (0x202) 54 No No 0 1 2 3
12820 e4:d3:f1:a5:93:79 2049 (0x801) 32 No No 0 1 2 3
12936 00:d0:97:6c:eb:00 513 (0x201) 36 No No 0 1 2 3
12952 00:0d:5d:0a:5c:4c 514 (0x202) 54 No No 0 1 2 3
13680 00:04:4d:da:2f:c0 513 (0x201) 36 No No 0 1 2 3
13768 00:18:71:74:79:8e 514 (0x202) 54 No No 0 1 2 3
13900 00:04:4d:bf:1e:40 513 (0x201) 36 No No 0 1 2 3
13992 e0:52:2d:4c:bd:00 2049 (0x801) 0 No No 0 1 2 3
14020 00:0d:5d:0a:52:06 514 (0x202) 54 No No 0 1 2 3
14172 00:b0:64:fd:43:36 513 (0x201) 36 No No 0 1 2 3
14392 e4:d3:f1:a5:93:76 2049 (0x801) 32 No No 0 1 2 3
14456 00:0d:5d:0a:50:be 514 (0x202) 54 No No 0 1 2 3
14808 00:b0:64:fd:18:4c 513 (0x201) 36 No No 0 1 2 3
14944 fc:1f:87:cb:63:00 2049 (0x801) 4 No No 0 1 2 3
14980 00:04:4d:da:64:80 513 (0x201) 36 No No 0 1 2 3
15064 4e:41:50:00:10:01 2050 (0x802) 40 No No 0 1 2 3
15392 00:0d:5d:0a:50:ec 513 (0x201) 36 No No 0 1 2 3
15572 00:0d:5d:09:3c:5f 514 (0x202) 54 No No 0 1 2 3
15620 01:4d:4c:41:50:01 2049 (0x801) - Yes Yes 0 1 2 3
15780 00:10:7b:e8:70:4d 513 (0x201) 36 No No 0 1 2 3
15796 00:0d:5d:0a:50:c2 513 (0x201) 36 No No 0 1 2 3
15816 00:0d:5d:0a:52:bf 513 (0x201) 36 No No 0 1 2 3
15888 4c:4e:35:b6:48:fc 2049 (0x801) 40 No No 0 1 2 3
16808 00:0d:5d:0a:50:fa 514 (0x202) 54 No No 0 1 2 3
16868 00:16:47:e4:b0:70 513 (0x201) 36 No No 0 1 2 3
17368 00:04:4d:da:14:c0 513 (0x201) 36 No No 0 1 2 3
17520 00:04:4d:da:53:00 513 (0x201) 36 No No 0 1 2 3
17712 4c:4e:35:b6:48:fc 513 (0x201) 40 No No 0 1 2 3
18116 00:13:80:44:f9:a0 513 (0x201) 36 No No 0 1 2 3
18364 00:0d:5d:0a:52:bd 513 (0x201) 36 No No 0 1 2 3
18496 00:11:43:5a:f4:c4 513 (0x201) 36 No No 0 1 2 3
19388 00:10:7b:3b:9c:48 513 (0x201) 36 No No 0 1 2 3
19604 00:b0:64:fd:17:e2 513 (0x201) 36 No No 0 1 2 3
19772 00:0d:5d:0a:d8:fe 513 (0x201) 36 No No 0 1 2 3
19976 00:1c:f6:37:b0:00 513 (0x201) 36 No No 0 1 2 3
20044 00:12:44:d9:f0:c0 514 (0x202) 54 No No 0 1 2 3
20144 4e:41:50:00:11:01 2050 (0x802) 32 No No 0 1 2 3
20364 42:80:8f:09:d1:78 513 (0x201) 36 No No 0 1 2 3
20444 00:0d:5d:0a:50:a7 513 (0x201) 36 No No 0 1 2 3
20632 00:04:4d:da:2d:80 513 (0x201) 36 No No 0 1 2 3
20652 00:60:f4:fa:21:00 513 (0x201) 36 No No 0 1 2 3
20884 00:04:4d:d8:47:40 513 (0x201) 36 No No 0 1 2 3
20896 b4:14:89:60:d8:80 514 (0x202) 54 No No 0 1 2 3
20924 00:1c:58:38:52:68 513 (0x201) 36 No No 0 1 2 3
21060 00:04:4d:d9:f3:80 513 (0x201) 36 No No 0 1 2 3
21268 00:0d:5d:0a:50:c4 513 (0x201) 36 No No 0 1 2 3
21332 00:04:4d:d8:7d:40 513 (0x201) 36 No No 0 1 2 3
21436 00:04:4d:d8:74:80 513 (0x201) 36 No No 0 1 2 3
21476 00:0d:5d:0a:52:a3 513 (0x201) 36 No No 0 1 2 3
21568 64:00:f1:41:ff:de 513 (0x201) 36 No No 0 1 2 3
21968 e2:3b:4d:f0:ea:00 2049 (0x801) 10 No No 0 1 2 3
22364 e2:3b:4d:f0:1d:00 2049 (0x801) 20 No No 0 1 2 3
22368 4e:41:50:00:07:15 2050 (0x802) 0 No No 0 1 2 3
22840 e0:50:bf:1c:f1:00 2049 (0x801) 16 No No 0 1 2 3
22860 00:04:4d:da:35:c0 513 (0x201) 36 No No 0 1 2 3
23168 4e:41:50:00:01:11 2050 (0x802) 18 No No 0 1 2 3
23876 00:04:4d:da:55:00 513 (0x201) 36 No No 0 1 2 3
26016 00:11:92:19:76:41 513 (0x201) 36 No No 0 1 2 3
26184 00:0b:be:aa:fe:85 513 (0x201) 36 No No 0 1 2 3
26228 00:0d:5d:0a:50:af 513 (0x201) 36 No No 0 1 2 3
26592 4c:4e:35:b6:48:f9 2049 (0x801) 38 No No 0 1 2 3
26632 00:1c:c0:4b:e5:72 513 (0x201) 36 No No 0 1 2 3
26816 00:0e:83:47:6f:06 513 (0x201) 36 No No 0 1 2 3
27188 4c:4e:35:b6:48:f9 1025 (0x401) 37 No No 0 1 2 3
27380 e8:04:62:1d:47:c0 513 (0x201) 36 No No 0 1 2 3
27620 e4:d3:f1:a5:93:7c 2049 (0x801) 32 No No 0 1 2 3
28088 00:12:00:42:3d:80 513 (0x201) 36 No No 0 1 2 3
28264 e0:50:bf:1c:f1:03 2049 (0x801) 16 No No 0 1 2 3
28420 00:10:7b:e8:09:b7 513 (0x201) 36 No No 0 1 2 3
28504 e0:52:2d:4c:bd:05 2049 (0x801) 0 No No 0 1 2 3
28532 00:04:4d:da:5e:40 513 (0x201) 36 No No 0 1 2 3
28704 01:4d:4c:41:50:00 2049 (0x801) - Yes Yes 0 1 2 3
28888 00:1a:4b:f8:a4:34 513 (0x201) 36 No No 0 1 2 3
29104 00:04:4d:da:18:c0 513 (0x201) 36 No No 0 1 2 3
29284 00:b0:64:fd:43:50 513 (0x201) 36 No No 0 1 2 3
29412 e4:d3:f1:a5:93:78 1025 (0x401) 34 No No 0 1 2 3
29472 00:d0:97:6c:f8:80 514 (0x202) 54 No No 0 1 2 3
29628 00:04:4d:b2:1e:80 513 (0x201) 36 No No 0 1 2 3
29924 4e:41:50:00:07:12 2050 (0x802) 0 No No 0 1 2 3
30020 00:00:0c:46:e4:f8 513 (0x201) 36 No No 0 1 2 3
30200 64:00:f1:42:07:da 514 (0x202) 54 No No 0 1 2 3
30364 00:04:4d:b4:38:80 513 (0x201) 36 No No 0 1 2 3
32040 e2:3b:4f:77:04:05 2049 (0x801) 18 No No 0 1 2 3
32184 4e:41:50:00:00:01 2050 (0x802) 16 No No 0 1 2 3
32572 4c:4e:35:b6:48:fe 514 (0x202) 40 No No 0 1 2 3
Total table entries: 127
Rack Card Switch
------------------
0 RP1 RP-SW
FDB Src Synced
Index MAC Address VLAN Port Trap Static Cores
----------------------------------------------------------------------
396 00:b0:64:fd:51:68 513 (0x201) 36 No No 0 1 2 3
504 e0:52:2d:4c:bd:03 2049 (0x801) 32 No No 0 1 2 3
804 00:04:4d:d8:6a:c0 514 (0x202) 54 No No 0 1 2 3
960 00:50:54:80:a5:fb 513 (0x201) 36 No No 0 1 2 3
1724 e0:50:a0:bf:8c:00 2049 (0x801) 32 No No 0 1 2 3
1896 00:00:0c:07:ac:02 513 (0x201) 36 No No 0 1 2 3
1932 00:b0:64:fd:18:1c 513 (0x201) 36 No No 0 1 2 3
2092 00:10:7b:e8:09:f8 513 (0x201) 36 No No 0 1 2 3
2368 4c:4e:35:b6:48:ff 2049 (0x801) 32 No No 0 1 2 3
2512 4e:41:50:00:01:01 2050 (0x802) 32 No No 0 1 2 3
2756 00:04:4d:da:5b:40 513 (0x201) 36 No No 0 1 2 3
2920 e0:50:a0:bf:8c:00 1025 (0x401) 5 No No 0 1 2 3
2984 00:13:80:31:74:80 513 (0x201) 36 No No 0 1 2 3
3636 00:12:44:d9:f0:c0 513 (0x201) 36 No No 0 1 2 3
3732 00:04:4d:da:3c:c0 513 (0x201) 36 No No 0 1 2 3
4244 00:00:0c:07:ac:5a 513 (0x201) 36 No No 0 1 2 3
4324 4e:41:50:00:07:01 2050 (0x802) 32 No No 0 1 2 3
4356 00:17:5a:af:71:58 513 (0x201) 36 No No 0 1 2 3
4568 b4:14:89:60:d8:80 513 (0x201) 36 No No 0 1 2 3
4648 00:00:0c:07:ac:28 513 (0x201) 36 No No 0 1 2 3
4772 00:00:0c:07:ac:32 513 (0x201) 36 No No 0 1 2 3
5000 e2:3b:4f:77:04:03 2049 (0x801) 32 No No 0 1 2 3
5196 e2:3b:43:46:6c:00 1025 (0x401) 21 No No 0 1 2 3
5296 00:04:4d:da:13:40 513 (0x201) 36 No No 0 1 2 3
5588 00:00:0c:07:ac:3c 514 (0x202) 54 No No 0 1 2 3
5624 e0:50:72:f4:dd:05 513 (0x201) 36 No No 0 1 2 3
5712 e2:3b:4d:f0:93:00 2049 (0x801) 32 No No 0 1 2 3
6092 00:04:4d:d8:4d:00 513 (0x201) 36 No No 0 1 2 3
6552 e2:3b:43:46:6c:00 2049 (0x801) 32 No No 0 1 2 3
6584 4e:41:50:00:00:12 2050 (0x802) 32 No No 0 1 2 3
6656 6c:9c:ed:79:92:90 513 (0x201) 36 No No 0 1 2 3
7044 e2:3b:4d:f0:93:00 1025 (0x401) 10 No No 0 1 2 3
7572 4c:4e:35:b6:48:fb 2049 (0x801) 32 No No 0 1 2 3
9048 88:43:e1:c2:b6:56 513 (0x201) 36 No No 0 1 2 3
9356 00:04:4d:b2:47:00 514 (0x202) 54 No No 0 1 2 3
9432 e2:3b:4f:77:04:00 2049 (0x801) 32 No No 0 1 2 3
9468 00:16:47:e4:b0:57 513 (0x201) 36 No No 0 1 2 3
10508 e2:3b:4f:77:04:00 1025 (0x401) 2 No No 0 1 2 3
10596 00:b0:64:fd:56:14 513 (0x201) 36 No No 0 1 2 3
11648 78:2b:cb:1e:0a:b3 513 (0x201) 36 No No 0 1 2 3
12008 4e:41:50:00:00:11 2050 (0x802) 32 No No 0 1 2 3
12344 00:00:0c:07:ac:01 513 (0x201) 36 No No 0 1 2 3
12496 01:4d:4c:41:50:01 1025 (0x401) - Yes Yes 0 1 2 3
12772 64:00:f1:42:09:12 514 (0x202) 54 No No 0 1 2 3
12820 e4:d3:f1:a5:93:79 2049 (0x801) 40 No No 0 1 2 3
12936 00:d0:97:6c:eb:00 513 (0x201) 36 No No 0 1 2 3
12952 00:0d:5d:0a:5c:4c 514 (0x202) 54 No No 0 1 2 3
13680 00:04:4d:da:2f:c0 513 (0x201) 36 No No 0 1 2 3
13768 00:18:71:74:79:8e 514 (0x202) 54 No No 0 1 2 3
13804 e4:d3:f1:a5:93:76 1025 (0x401) 37 No No 0 1 2 3
13900 00:04:4d:bf:1e:40 513 (0x201) 36 No No 0 1 2 3
13992 e0:52:2d:4c:bd:00 2049 (0x801) 32 No No 0 1 2 3
14020 00:0d:5d:0a:52:06 514 (0x202) 54 No No 0 1 2 3
14172 00:b0:64:fd:43:36 513 (0x201) 36 No No 0 1 2 3
14260 fc:1f:87:cb:63:00 1025 (0x401) 20 No No 0 1 2 3
14392 e4:d3:f1:a5:93:76 2049 (0x801) 38 No No 0 1 2 3
14456 00:0d:5d:0a:50:be 514 (0x202) 54 No No 0 1 2 3
14808 00:b0:64:fd:18:4c 513 (0x201) 36 No No 0 1 2 3
14944 fc:1f:87:cb:63:00 2049 (0x801) 32 No No 0 1 2 3
14980 00:04:4d:da:64:80 513 (0x201) 36 No No 0 1 2 3
15064 4e:41:50:00:10:01 2050 (0x802) 32 No No 0 1 2 3
15228 e0:52:2d:4c:bd:00 1025 (0x401) 16 No No 0 1 2 3
15392 00:0d:5d:0a:50:ec 513 (0x201) 36 No No 0 1 2 3
15572 00:0d:5d:09:3c:5f 514 (0x202) 54 No No 0 1 2 3
15620 01:4d:4c:41:50:01 2049 (0x801) - Yes Yes 0 1 2 3
15780 00:10:7b:e8:70:4d 513 (0x201) 36 No No 0 1 2 3
15796 00:0d:5d:0a:50:c2 513 (0x201) 36 No No 0 1 2 3
15816 00:0d:5d:0a:52:bf 513 (0x201) 36 No No 0 1 2 3
15888 4c:4e:35:b6:48:fc 2049 (0x801) 32 No No 0 1 2 3
16808 00:0d:5d:0a:50:fa 514 (0x202) 54 No No 0 1 2 3
17368 00:04:4d:da:14:c0 513 (0x201) 36 No No 0 1 2 3
17520 00:04:4d:da:53:00 513 (0x201) 36 No No 0 1 2 3
18116 00:13:80:44:f9:a0 513 (0x201) 36 No No 0 1 2 3
18364 00:0d:5d:0a:52:bd 513 (0x201) 36 No No 0 1 2 3
18496 00:11:43:5a:f4:c4 513 (0x201) 36 No No 0 1 2 3
18740 e4:d3:f1:a5:93:79 513 (0x201) 40 No No 0 1 2 3
19388 00:10:7b:3b:9c:48 513 (0x201) 36 No No 0 1 2 3
19604 00:b0:64:fd:17:e2 513 (0x201) 36 No No 0 1 2 3
19772 00:0d:5d:0a:d8:fe 513 (0x201) 36 No No 0 1 2 3
19976 00:1c:f6:37:b0:00 513 (0x201) 36 No No 0 1 2 3
20044 00:12:44:d9:f0:c0 514 (0x202) 54 No No 0 1 2 3
20144 4e:41:50:00:11:01 2050 (0x802) 40 No No 0 1 2 3
20364 42:80:8f:09:d1:78 513 (0x201) 36 No No 0 1 2 3
20444 00:0d:5d:0a:50:a7 513 (0x201) 36 No No 0 1 2 3
20632 00:04:4d:da:2d:80 513 (0x201) 36 No No 0 1 2 3
20652 00:60:f4:fa:21:00 513 (0x201) 36 No No 0 1 2 3
20884 00:04:4d:d8:47:40 513 (0x201) 36 No No 0 1 2 3
20896 b4:14:89:60:d8:80 514 (0x202) 54 No No 0 1 2 3
20924 00:1c:58:38:52:68 513 (0x201) 36 No No 0 1 2 3
21060 00:04:4d:d9:f3:80 513 (0x201) 36 No No 0 1 2 3
21268 00:0d:5d:0a:50:c4 513 (0x201) 36 No No 0 1 2 3
21332 00:04:4d:d8:7d:40 513 (0x201) 36 No No 0 1 2 3
21436 00:04:4d:d8:74:80 513 (0x201) 36 No No 0 1 2 3
21476 00:0d:5d:0a:52:a3 513 (0x201) 36 No No 0 1 2 3
21568 64:00:f1:41:ff:de 513 (0x201) 36 No No 0 1 2 3
21740 e0:50:bf:1c:f1:00 1025 (0x401) 0 No No 0 1 2 3
21848 12:e8:cb:51:07:4b 513 (0x201) 40 No No 0 1 2 3
21968 e2:3b:4d:f0:ea:00 2049 (0x801) 32 No No 0 1 2 3
22364 e2:3b:4d:f0:1d:00 2049 (0x801) 32 No No 0 1 2 3
22368 4e:41:50:00:07:15 2050 (0x802) 32 No No 0 1 2 3
22532 e2:3b:4d:f0:ea:00 1025 (0x401) 26 No No 0 1 2 3
22636 00:16:47:e4:b0:75 514 (0x202) 54 No No 0 1 2 3
22840 e0:50:bf:1c:f1:00 2049 (0x801) 32 No No 0 1 2 3
22860 00:04:4d:da:35:c0 513 (0x201) 36 No No 0 1 2 3
23168 4e:41:50:00:01:11 2050 (0x802) 32 No No 0 1 2 3
23176 e2:3b:4d:f0:1d:00 1025 (0x401) 4 No No 0 1 2 3
23876 00:04:4d:da:55:00 513 (0x201) 36 No No 0 1 2 3
26016 00:11:92:19:76:41 513 (0x201) 36 No No 0 1 2 3
26184 00:0b:be:aa:fe:85 513 (0x201) 36 No No 0 1 2 3
26228 00:0d:5d:0a:50:af 513 (0x201) 36 No No 0 1 2 3
26592 4c:4e:35:b6:48:f9 2049 (0x801) 32 No No 0 1 2 3
26632 00:1c:c0:4b:e5:72 513 (0x201) 36 No No 0 1 2 3
26816 00:0e:83:47:6f:06 513 (0x201) 36 No No 0 1 2 3
27188 4c:4e:35:b6:48:f9 1025 (0x401) 34 No No 0 1 2 3
27380 e8:04:62:1d:47:c0 513 (0x201) 36 No No 0 1 2 3
27620 e4:d3:f1:a5:93:7c 2049 (0x801) 40 No No 0 1 2 3
28088 00:12:00:42:3d:80 513 (0x201) 36 No No 0 1 2 3
28264 e0:50:bf:1c:f1:03 2049 (0x801) 32 No No 0 1 2 3
28420 00:10:7b:e8:09:b7 513 (0x201) 36 No No 0 1 2 3
28532 00:04:4d:da:5e:40 513 (0x201) 36 No No 0 1 2 3
28704 e4:d3:f1:a5:95:38 513 (0x201) 40 No No 0 1 2 3
28888 00:1a:4b:f8:a4:34 513 (0x201) 36 No No 0 1 2 3
29104 00:04:4d:da:18:c0 513 (0x201) 36 No No 0 1 2 3
29284 00:b0:64:fd:43:50 513 (0x201) 36 No No 0 1 2 3
29412 e4:d3:f1:a5:93:78 1025 (0x401) - Yes Yes 0 1 2 3
29472 00:d0:97:6c:f8:80 514 (0x202) 54 No No 0 1 2 3
29496 e4:d3:f1:a5:93:7b 514 (0x202) 40 No No 0 1 2 3
29628 00:04:4d:b2:1e:80 513 (0x201) 36 No No 0 1 2 3
29924 4e:41:50:00:07:12 2050 (0x802) 32 No No 0 1 2 3
30020 00:00:0c:46:e4:f8 513 (0x201) 36 No No 0 1 2 3
30200 64:00:f1:42:07:da 514 (0x202) 54 No No 0 1 2 3
30364 00:04:4d:b4:38:80 513 (0x201) 36 No No 0 1 2 3
32184 4e:41:50:00:00:01 2050 (0x802) 32 No No 0 1 2 3
32244 01:4d:4c:41:50:00 1025 (0x401) - Yes Yes 0 1 2 3
Total table entries: 134
Rack Card Switch
------------------
0 LC0 LC-SW
FDB Src Synced
Index MAC Address VLAN Port Trap Static Cores
---------------------------------------------------------------------
4 00:0d:5d:0a:5c:33 513 (0x201) 42 No No 0 2
200 e0:50:bf:1c:f1:05 2049 (0x801) 0 No No 0 2
328 00:1c:58:38:52:3e 513 (0x201) 42 No No 0 2
396 00:b0:64:fd:51:68 513 (0x201) 42 No No 0 2
476 00:b0:64:fd:18:a4 513 (0x201) 42 No No 0 2
477 00:b0:64:fd:20:ab 513 (0x201) 42 No No 0 2
504 e0:52:2d:4c:bd:03 2049 (0x801) 2 No No 0 2
960 00:50:54:80:a5:fb 513 (0x201) 42 No No 0 2
1688 00:0d:5d:0a:50:76 513 (0x201) 42 No No 0 2
1896 00:00:0c:07:ac:02 513 (0x201) 42 No No 0 2
1932 00:b0:64:fd:18:1c 513 (0x201) 42 No No 0 2
2092 00:10:7b:e8:09:f8 513 (0x201) 42 No No 0 2
2136 00:0d:5d:0a:50:b3 513 (0x201) 42 No No 0 2
2512 4e:41:50:00:01:01 2050 (0x802) 2 No No 0 2
2756 00:04:4d:da:5b:40 513 (0x201) 42 No No 0 2
2984 00:13:80:31:74:80 513 (0x201) 42 No No 0 2
3636 00:12:44:d9:f0:c0 513 (0x201) 42 No No 0 2
3732 00:04:4d:da:3c:c0 513 (0x201) 42 No No 0 2
4096 00:b0:64:fd:4b:fc 513 (0x201) 42 No No 0 2
4244 00:00:0c:07:ac:5a 513 (0x201) 42 No No 0 2
4324 4e:41:50:00:07:01 2050 (0x802) 2 No No 0 2
4356 00:17:5a:af:71:58 513 (0x201) 42 No No 0 2
4568 b4:14:89:60:d8:80 513 (0x201) 42 No No 0 2
4648 00:00:0c:07:ac:28 513 (0x201) 42 No No 0 2
4772 00:00:0c:07:ac:32 513 (0x201) 42 No No 0 2
5000 e2:3b:4f:77:04:03 2049 (0x801) 2 No No 0 2
5296 00:04:4d:da:13:40 513 (0x201) 42 No No 0 2
5448 e0:50:bf:1c:f1:03 513 (0x201) 0 No No 0 2
5624 e0:50:72:f4:dd:05 513 (0x201) 42 No No 0 2
6092 00:04:4d:d8:4d:00 513 (0x201) 42 No No 0 2
6312 00:1a:6c:40:e0:20 513 (0x201) 42 No No 0 2
6584 4e:41:50:00:00:12 2050 (0x802) 34 No No 0 2
6656 6c:9c:ed:79:92:90 513 (0x201) 42 No No 0 2
7092 1e:f5:5c:2a:09:38 513 (0x201) 0 No No 0 2
7096 00:0d:5d:0a:52:46 513 (0x201) 42 No No 0 2
7112 00:18:71:4d:48:42 513 (0x201) 42 No No 0 2
7532 00:10:7b:e8:09:d2 513 (0x201) 42 No No 0 2
7572 4c:4e:35:b6:48:fb 2049 (0x801) 2 No No 0 2
9048 88:43:e1:c2:b6:56 513 (0x201) 42 No No 0 2
10484 00:0d:5d:0a:50:e8 513 (0x201) 42 No No 0 2
10596 00:b0:64:fd:56:14 513 (0x201) 42 No No 0 2
10732 00:0d:5d:0a:50:dc 513 (0x201) 42 No No 0 2
11648 78:2b:cb:1e:0a:b3 513 (0x201) 42 No No 0 2
12008 4e:41:50:00:00:11 2050 (0x802) 36 No No 0 2
12344 00:00:0c:07:ac:01 513 (0x201) 42 No No 0 2
12496 01:4d:4c:41:50:01 1025 (0x401) - Yes Yes 0 2
12820 e4:d3:f1:a5:93:79 2049 (0x801) 2 No No 0 2
12936 00:d0:97:6c:eb:00 513 (0x201) 42 No No 0 2
13680 00:04:4d:da:2f:c0 513 (0x201) 42 No No 0 2
13900 00:04:4d:bf:1e:40 513 (0x201) 42 No No 0 2
14172 00:b0:64:fd:43:36 513 (0x201) 42 No No 0 2
14808 00:b0:64:fd:18:4c 513 (0x201) 42 No No 0 2
14980 00:04:4d:da:64:80 513 (0x201) 42 No No 0 2
15064 4e:41:50:00:10:01 2050 (0x802) 2 No No 0 2
15392 00:0d:5d:0a:50:ec 513 (0x201) 42 No No 0 2
15620 01:4d:4c:41:50:01 2049 (0x801) - Yes Yes 0 2
15780 00:10:7b:e8:70:4d 513 (0x201) 42 No No 0 2
15796 00:0d:5d:0a:50:c2 513 (0x201) 42 No No 0 2
15816 00:0d:5d:0a:52:bf 513 (0x201) 42 No No 0 2
15888 4c:4e:35:b6:48:fc 2049 (0x801) 2 No No 0 2
15928 00:10:7b:3b:80:52 513 (0x201) 42 No No 0 2
15964 e0:50:bf:1c:f1:79 513 (0x201) 0 No No 0 2
17368 00:04:4d:da:14:c0 513 (0x201) 42 No No 0 2
17520 00:04:4d:da:53:00 513 (0x201) 42 No No 0 2
17640 00:0d:5d:0a:50:9c 513 (0x201) 42 No No 0 2
18092 00:10:7b:e8:09:bf 513 (0x201) 42 No No 0 2
18116 00:13:80:44:f9:a0 513 (0x201) 42 No No 0 2
18132 00:b0:64:fd:18:aa 513 (0x201) 42 No No 0 2
18360 a0:00:b0:01:c1:a2 513 (0x201) 42 No No 0 2
18364 00:0d:5d:0a:52:bd 513 (0x201) 42 No No 0 2
18496 00:11:43:5a:f4:c4 513 (0x201) 42 No No 0 2
19388 00:10:7b:3b:9c:48 513 (0x201) 42 No No 0 2
19604 00:b0:64:fd:17:e2 513 (0x201) 42 No No 0 2
19772 00:0d:5d:0a:d8:fe 513 (0x201) 42 No No 0 2
19976 00:1c:f6:37:b0:00 513 (0x201) 42 No No 0 2
20144 4e:41:50:00:11:01 2050 (0x802) 2 No No 0 2
20364 42:80:8f:09:d1:78 513 (0x201) 42 No No 0 2
20444 00:0d:5d:0a:50:a7 513 (0x201) 42 No No 0 2
20632 00:04:4d:da:2d:80 513 (0x201) 42 No No 0 2
20652 00:60:f4:fa:21:00 513 (0x201) 42 No No 0 2
20884 00:04:4d:d8:47:40 513 (0x201) 42 No No 0 2
20924 00:1c:58:38:52:68 513 (0x201) 42 No No 0 2
21060 00:04:4d:d9:f3:80 513 (0x201) 42 No No 0 2
21268 00:0d:5d:0a:50:c4 513 (0x201) 42 No No 0 2
21332 00:04:4d:d8:7d:40 513 (0x201) 42 No No 0 2
21436 00:04:4d:d8:74:80 513 (0x201) 42 No No 0 2
21476 00:0d:5d:0a:52:a3 513 (0x201) 42 No No 0 2
21568 64:00:f1:41:ff:de 513 (0x201) 42 No No 0 2
21740 e0:50:bf:1c:f1:00 1025 (0x401) 9 No No 0 2
22304 00:b0:64:fd:1f:0a 513 (0x201) 42 No No 0 2
22516 78:2b:cb:1e:0a:b1 513 (0x201) 42 No No 0 2
22840 e0:50:bf:1c:f1:00 2049 (0x801) 8 No No 0 2
22860 00:04:4d:da:35:c0 513 (0x201) 42 No No 0 2
23568 00:0d:5d:0a:51:f2 513 (0x201) 42 No No 0 2
23876 00:04:4d:da:55:00 513 (0x201) 42 No No 0 2
25596 00:0d:5d:0a:22:32 513 (0x201) 42 No No 0 2
26016 00:11:92:19:76:41 513 (0x201) 42 No No 0 2
26184 00:0b:be:aa:fe:85 513 (0x201) 42 No No 0 2
26228 00:0d:5d:0a:50:af 513 (0x201) 42 No No 0 2
26536 00:b0:64:fd:43:60 513 (0x201) 42 No No 0 2
26632 00:1c:c0:4b:e5:72 513 (0x201) 42 No No 0 2
26816 00:0e:83:47:6f:06 513 (0x201) 42 No No 0 2
27048 00:15:62:c9:3d:00 513 (0x201) 42 No No 0 2
27380 e8:04:62:1d:47:c0 513 (0x201) 42 No No 0 2
28088 00:12:00:42:3d:80 513 (0x201) 42 No No 0 2
28264 e0:50:bf:1c:f1:03 2049 (0x801) 0 No No 0 2
28420 00:10:7b:e8:09:b7 513 (0x201) 42 No No 0 2
28532 00:04:4d:da:5e:40 513 (0x201) 42 No No 0 2
28668 00:0d:5d:0a:50:e6 513 (0x201) 42 No No 0 2
28888 00:1a:4b:f8:a4:34 513 (0x201) 42 No No 0 2
29104 00:04:4d:da:18:c0 513 (0x201) 42 No No 0 2
29284 00:b0:64:fd:43:50 513 (0x201) 42 No No 0 2
29412 e4:d3:f1:a5:93:78 1025 (0x401) 4 No No 0 2
29628 00:04:4d:b2:1e:80 513 (0x201) 42 No No 0 2
29696 00:0d:5d:0a:52:74 513 (0x201) 42 No No 0 2
30020 00:00:0c:46:e4:f8 513 (0x201) 42 No No 0 2
30316 00:1c:58:38:5a:b8 513 (0x201) 42 No No 0 2
30364 00:04:4d:b4:38:80 513 (0x201) 42 No No 0 2
31308 00:0d:5d:0a:52:ab 513 (0x201) 42 No No 0 2
31348 00:19:d1:e3:07:78 513 (0x201) 42 No No 0 2
31764 00:16:47:e4:b0:66 513 (0x201) 42 No No 0 2
32184 4e:41:50:00:00:01 2050 (0x802) 0 No No 0 2
32464 00:11:85:69:d0:f9 513 (0x201) 42 No No 0 2
Total table entries: 123
Rack Card Switch
------------------
0 LC1 LC-SW
FDB Src Synced
Index MAC Address VLAN Port Trap Static Cores
---------------------------------------------------------------------
4 00:0d:5d:0a:5c:33 513 (0x201) 42 No No 0 2
328 00:1c:58:38:52:3e 513 (0x201) 42 No No 0 2
396 00:b0:64:fd:51:68 513 (0x201) 42 No No 0 2
476 00:b0:64:fd:18:a4 513 (0x201) 42 No No 0 2
477 00:b0:64:fd:20:ab 513 (0x201) 42 No No 0 2
504 e0:52:2d:4c:bd:03 2049 (0x801) 2 No No 0 2
960 00:50:54:80:a5:fb 513 (0x201) 42 No No 0 2
1688 00:0d:5d:0a:50:76 513 (0x201) 42 No No 0 2
1896 00:00:0c:07:ac:02 513 (0x201) 42 No No 0 2
1932 00:b0:64:fd:18:1c 513 (0x201) 42 No No 0 2
2092 00:10:7b:e8:09:f8 513 (0x201) 42 No No 0 2
2136 00:0d:5d:0a:50:b3 513 (0x201) 42 No No 0 2
2512 4e:41:50:00:01:01 2050 (0x802) 0 No No 0 2
2756 00:04:4d:da:5b:40 513 (0x201) 42 No No 0 2
2984 00:13:80:31:74:80 513 (0x201) 42 No No 0 2
3636 00:12:44:d9:f0:c0 513 (0x201) 42 No No 0 2
3732 00:04:4d:da:3c:c0 513 (0x201) 42 No No 0 2
4096 00:b0:64:fd:4b:fc 513 (0x201) 42 No No 0 2
4244 00:00:0c:07:ac:5a 513 (0x201) 42 No No 0 2
4324 4e:41:50:00:07:01 2050 (0x802) 2 No No 0 2
4356 00:17:5a:af:71:58 513 (0x201) 42 No No 0 2
4568 b4:14:89:60:d8:80 513 (0x201) 42 No No 0 2
4648 00:00:0c:07:ac:28 513 (0x201) 42 No No 0 2
4772 00:00:0c:07:ac:32 513 (0x201) 42 No No 0 2
5000 e2:3b:4f:77:04:03 2049 (0x801) 0 No No 0 2
5296 00:04:4d:da:13:40 513 (0x201) 42 No No 0 2
5624 e0:50:72:f4:dd:05 513 (0x201) 42 No No 0 2
6092 00:04:4d:d8:4d:00 513 (0x201) 42 No No 0 2
6312 00:1a:6c:40:e0:20 513 (0x201) 42 No No 0 2
6656 6c:9c:ed:79:92:90 513 (0x201) 42 No No 0 2
7096 00:0d:5d:0a:52:46 513 (0x201) 42 No No 0 2
7112 00:18:71:4d:48:42 513 (0x201) 42 No No 0 2
7532 00:10:7b:e8:09:d2 513 (0x201) 42 No No 0 2
7572 4c:4e:35:b6:48:fb 2049 (0x801) 2 No No 0 2
9048 88:43:e1:c2:b6:56 513 (0x201) 42 No No 0 2
9432 e2:3b:4f:77:04:00 2049 (0x801) 8 No No 0 2
10484 00:0d:5d:0a:50:e8 513 (0x201) 42 No No 0 2
10508 e2:3b:4f:77:04:00 1025 (0x401) 9 No No 0 2
10596 00:b0:64:fd:56:14 513 (0x201) 42 No No 0 2
10732 00:0d:5d:0a:50:dc 513 (0x201) 42 No No 0 2
11648 78:2b:cb:1e:0a:b3 513 (0x201) 42 No No 0 2
12344 00:00:0c:07:ac:01 513 (0x201) 42 No No 0 2
12496 01:4d:4c:41:50:01 1025 (0x401) - Yes Yes 0 2
12592 00:16:47:e4:b0:67 513 (0x201) 42 No No 0 2
12820 e4:d3:f1:a5:93:79 2049 (0x801) 2 No No 0 2
12936 00:d0:97:6c:eb:00 513 (0x201) 42 No No 0 2
13680 00:04:4d:da:2f:c0 513 (0x201) 42 No No 0 2
13900 00:04:4d:bf:1e:40 513 (0x201) 42 No No 0 2
14172 00:b0:64:fd:43:36 513 (0x201) 42 No No 0 2
14808 00:b0:64:fd:18:4c 513 (0x201) 42 No No 0 2
14980 00:04:4d:da:64:80 513 (0x201) 42 No No 0 2
15064 4e:41:50:00:10:01 2050 (0x802) 2 No No 0 2
15392 00:0d:5d:0a:50:ec 513 (0x201) 42 No No 0 2
15620 01:4d:4c:41:50:01 2049 (0x801) - Yes Yes 0 2
15780 00:10:7b:e8:70:4d 513 (0x201) 42 No No 0 2
15796 00:0d:5d:0a:50:c2 513 (0x201) 42 No No 0 2
15816 00:0d:5d:0a:52:bf 513 (0x201) 42 No No 0 2
15888 4c:4e:35:b6:48:fc 2049 (0x801) 2 No No 0 2
15928 00:10:7b:3b:80:52 513 (0x201) 42 No No 0 2
17340 e2:3b:4f:77:04:79 513 (0x201) 0 No No 0 2
17368 00:04:4d:da:14:c0 513 (0x201) 42 No No 0 2
17460 aa:93:c3:2b:71:7e 513 (0x201) 0 No No 0 2
17520 00:04:4d:da:53:00 513 (0x201) 42 No No 0 2
17640 00:0d:5d:0a:50:9c 513 (0x201) 42 No No 0 2
18092 00:10:7b:e8:09:bf 513 (0x201) 42 No No 0 2
18116 00:13:80:44:f9:a0 513 (0x201) 42 No No 0 2
18132 00:b0:64:fd:18:aa 513 (0x201) 42 No No 0 2
18360 a0:00:b0:01:c1:a2 513 (0x201) 42 No No 0 2
18364 00:0d:5d:0a:52:bd 513 (0x201) 42 No No 0 2
18496 00:11:43:5a:f4:c4 513 (0x201) 42 No No 0 2
19388 00:10:7b:3b:9c:48 513 (0x201) 42 No No 0 2
19604 00:b0:64:fd:17:e2 513 (0x201) 42 No No 0 2
19772 00:0d:5d:0a:d8:fe 513 (0x201) 42 No No 0 2
19976 00:1c:f6:37:b0:00 513 (0x201) 42 No No 0 2
20144 4e:41:50:00:11:01 2050 (0x802) 2 No No 0 2
20364 42:80:8f:09:d1:78 513 (0x201) 42 No No 0 2
20444 00:0d:5d:0a:50:a7 513 (0x201) 42 No No 0 2
20632 00:04:4d:da:2d:80 513 (0x201) 42 No No 0 2
20652 00:60:f4:fa:21:00 513 (0x201) 42 No No 0 2
20884 00:04:4d:d8:47:40 513 (0x201) 42 No No 0 2
20924 00:1c:58:38:52:68 513 (0x201) 42 No No 0 2
21060 00:04:4d:d9:f3:80 513 (0x201) 42 No No 0 2
21268 00:0d:5d:0a:50:c4 513 (0x201) 42 No No 0 2
21332 00:04:4d:d8:7d:40 513 (0x201) 42 No No 0 2
21436 00:04:4d:d8:74:80 513 (0x201) 42 No No 0 2
21476 00:0d:5d:0a:52:a3 513 (0x201) 42 No No 0 2
21568 64:00:f1:41:ff:de 513 (0x201) 42 No No 0 2
22304 00:b0:64:fd:1f:0a 513 (0x201) 42 No No 0 2
22516 78:2b:cb:1e:0a:b1 513 (0x201) 42 No No 0 2
22860 00:04:4d:da:35:c0 513 (0x201) 42 No No 0 2
23168 4e:41:50:00:01:11 2050 (0x802) 34 No No 0 2
23568 00:0d:5d:0a:51:f2 513 (0x201) 42 No No 0 2
23876 00:04:4d:da:55:00 513 (0x201) 42 No No 0 2
25596 00:0d:5d:0a:22:32 513 (0x201) 42 No No 0 2
26016 00:11:92:19:76:41 513 (0x201) 42 No No 0 2
26184 00:0b:be:aa:fe:85 513 (0x201) 42 No No 0 2
26228 00:0d:5d:0a:50:af 513 (0x201) 42 No No 0 2
26536 00:b0:64:fd:43:60 513 (0x201) 42 No No 0 2
26632 00:1c:c0:4b:e5:72 513 (0x201) 42 No No 0 2
26792 e2:3b:4f:77:04:03 513 (0x201) 0 No No 0 2
26816 00:0e:83:47:6f:06 513 (0x201) 42 No No 0 2
27048 00:15:62:c9:3d:00 513 (0x201) 42 No No 0 2
27380 e8:04:62:1d:47:c0 513 (0x201) 42 No No 0 2
28088 00:12:00:42:3d:80 513 (0x201) 42 No No 0 2
28264 e0:50:bf:1c:f1:03 2049 (0x801) 2 No No 0 2
28420 00:10:7b:e8:09:b7 513 (0x201) 42 No No 0 2
28532 00:04:4d:da:5e:40 513 (0x201) 42 No No 0 2
28668 00:0d:5d:0a:50:e6 513 (0x201) 42 No No 0 2
28888 00:1a:4b:f8:a4:34 513 (0x201) 42 No No 0 2
29104 00:04:4d:da:18:c0 513 (0x201) 42 No No 0 2
29284 00:b0:64:fd:43:50 513 (0x201) 42 No No 0 2
29412 e4:d3:f1:a5:93:78 1025 (0x401) 4 No No 0 2
29628 00:04:4d:b2:1e:80 513 (0x201) 42 No No 0 2
29696 00:0d:5d:0a:52:74 513 (0x201) 42 No No 0 2
30020 00:00:0c:46:e4:f8 513 (0x201) 42 No No 0 2
30316 00:1c:58:38:5a:b8 513 (0x201) 42 No No 0 2
30364 00:04:4d:b4:38:80 513 (0x201) 42 No No 0 2
31308 00:0d:5d:0a:52:ab 513 (0x201) 42 No No 0 2
31348 00:19:d1:e3:07:78 513 (0x201) 42 No No 0 2
32040 e2:3b:4f:77:04:05 2049 (0x801) 0 No No 0 2
32184 4e:41:50:00:00:01 2050 (0x802) 2 No No 0 2
32464 00:11:85:69:d0:f9 513 (0x201) 42 No No 0 2
Total table entries: 122
Rack Card Switch
------------------
0 LC7 LC-SW
FDB Src Synced
Index MAC Address VLAN Port Trap Static Cores
---------------------------------------------------------------------
4 00:0d:5d:0a:5c:33 513 (0x201) 42 No No 0 2
328 00:1c:58:38:52:3e 513 (0x201) 42 No No 0 2
396 00:b0:64:fd:51:68 513 (0x201) 42 No No 0 2
476 00:b0:64:fd:18:a4 513 (0x201) 42 No No 0 2
477 00:b0:64:fd:20:ab 513 (0x201) 42 No No 0 2
504 e0:52:2d:4c:bd:03 2049 (0x801) 0 No No 0 2
508 b6:aa:1c:40:27:e2 513 (0x201) 0 No No 0 2
960 00:50:54:80:a5:fb 513 (0x201) 42 No No 0 2
1688 00:0d:5d:0a:50:76 513 (0x201) 42 No No 0 2
1896 00:00:0c:07:ac:02 513 (0x201) 42 No No 0 2
1932 00:b0:64:fd:18:1c 513 (0x201) 42 No No 0 2
2092 00:10:7b:e8:09:f8 513 (0x201) 42 No No 0 2
2136 00:0d:5d:0a:50:b3 513 (0x201) 42 No No 0 2
2513 4e:41:50:00:01:01 2050 (0x802) 2 No No 0 2
2756 00:04:4d:da:5b:40 513 (0x201) 42 No No 0 2
2984 00:13:80:31:74:80 513 (0x201) 42 No No 0 2
3636 00:12:44:d9:f0:c0 513 (0x201) 42 No No 0 2
3732 00:04:4d:da:3c:c0 513 (0x201) 42 No No 0 2
4096 00:b0:64:fd:4b:fc 513 (0x201) 42 No No 0 2
4244 00:00:0c:07:ac:5a 513 (0x201) 42 No No 0 2
4324 4e:41:50:00:07:01 2050 (0x802) 0 No No 0 2
4356 00:17:5a:af:71:58 513 (0x201) 42 No No 0 2
4568 b4:14:89:60:d8:80 513 (0x201) 42 No No 0 2
4648 00:00:0c:07:ac:28 513 (0x201) 42 No No 0 2
4772 00:00:0c:07:ac:32 513 (0x201) 42 No No 0 2
5000 e2:3b:4f:77:04:03 2049 (0x801) 2 No No 0 2
5296 00:04:4d:da:13:40 513 (0x201) 42 No No 0 2
5624 e0:50:72:f4:dd:05 513 (0x201) 42 No No 0 2
6092 00:04:4d:d8:4d:00 513 (0x201) 42 No No 0 2
6312 00:1a:6c:40:e0:20 513 (0x201) 42 No No 0 2
6656 6c:9c:ed:79:92:90 513 (0x201) 42 No No 0 2
7096 00:0d:5d:0a:52:46 513 (0x201) 42 No No 0 2
7112 00:18:71:4d:48:42 513 (0x201) 42 No No 0 2
7532 00:10:7b:e8:09:d2 513 (0x201) 42 No No 0 2
7572 4c:4e:35:b6:48:fb 2049 (0x801) 2 No No 0 2
9048 88:43:e1:c2:b6:56 513 (0x201) 42 No No 0 2
10484 00:0d:5d:0a:50:e8 513 (0x201) 42 No No 0 2
10596 00:b0:64:fd:56:14 513 (0x201) 42 No No 0 2
10732 00:0d:5d:0a:50:dc 513 (0x201) 42 No No 0 2
11648 78:2b:cb:1e:0a:b3 513 (0x201) 42 No No 0 2
12100 00:16:47:e4:b0:76 513 (0x201) 42 No No 0 2
12344 00:00:0c:07:ac:01 513 (0x201) 42 No No 0 2
12496 01:4d:4c:41:50:01 1025 (0x401) - Yes Yes 0 2
12820 e4:d3:f1:a5:93:79 2049 (0x801) 2 No No 0 2
12936 00:d0:97:6c:eb:00 513 (0x201) 42 No No 0 2
13680 00:04:4d:da:2f:c0 513 (0x201) 42 No No 0 2
13900 00:04:4d:bf:1e:40 513 (0x201) 42 No No 0 2
13992 e0:52:2d:4c:bd:00 2049 (0x801) 8 No No 0 2
14172 00:b0:64:fd:43:36 513 (0x201) 42 No No 0 2
14808 00:b0:64:fd:18:4c 513 (0x201) 42 No No 0 2
14980 00:04:4d:da:64:80 513 (0x201) 42 No No 0 2
15064 4e:41:50:00:10:01 2050 (0x802) 2 No No 0 2
15228 e0:52:2d:4c:bd:00 1025 (0x401) 9 No No 0 2
15392 00:0d:5d:0a:50:ec 513 (0x201) 42 No No 0 2
15620 01:4d:4c:41:50:01 2049 (0x801) - Yes Yes 0 2
15780 00:10:7b:e8:70:4d 513 (0x201) 42 No No 0 2
15796 00:0d:5d:0a:50:c2 513 (0x201) 42 No No 0 2
15816 00:0d:5d:0a:52:bf 513 (0x201) 42 No No 0 2
15888 4c:4e:35:b6:48:fc 2049 (0x801) 2 No No 0 2
15928 00:10:7b:3b:80:52 513 (0x201) 42 No No 0 2
17368 00:04:4d:da:14:c0 513 (0x201) 42 No No 0 2
17520 00:04:4d:da:53:00 513 (0x201) 42 No No 0 2
17640 00:0d:5d:0a:50:9c 513 (0x201) 42 No No 0 2
18092 00:10:7b:e8:09:bf 513 (0x201) 42 No No 0 2
18116 00:13:80:44:f9:a0 513 (0x201) 42 No No 0 2
18132 00:b0:64:fd:18:aa 513 (0x201) 42 No No 0 2
18360 a0:00:b0:01:c1:a2 513 (0x201) 42 No No 0 2
18364 00:0d:5d:0a:52:bd 513 (0x201) 42 No No 0 2
18496 00:11:43:5a:f4:c4 513 (0x201) 42 No No 0 2
19388 00:10:7b:3b:9c:48 513 (0x201) 42 No No 0 2
19604 00:b0:64:fd:17:e2 513 (0x201) 42 No No 0 2
19772 00:0d:5d:0a:d8:fe 513 (0x201) 42 No No 0 2
19976 00:1c:f6:37:b0:00 513 (0x201) 42 No No 0 2
20144 4e:41:50:00:11:01 2050 (0x802) 2 No No 0 2
20364 42:80:8f:09:d1:78 513 (0x201) 42 No No 0 2
20444 00:0d:5d:0a:50:a7 513 (0x201) 42 No No 0 2
20632 00:04:4d:da:2d:80 513 (0x201) 42 No No 0 2
20652 00:60:f4:fa:21:00 513 (0x201) 42 No No 0 2
20884 00:04:4d:d8:47:40 513 (0x201) 42 No No 0 2
20924 00:1c:58:38:52:68 513 (0x201) 42 No No 0 2
20940 e0:52:2d:4c:bd:79 513 (0x201) 0 No No 0 2
21060 00:04:4d:d9:f3:80 513 (0x201) 42 No No 0 2
21268 00:0d:5d:0a:50:c4 513 (0x201) 42 No No 0 2
21332 00:04:4d:d8:7d:40 513 (0x201) 42 No No 0 2
21436 00:04:4d:d8:74:80 513 (0x201) 42 No No 0 2
21476 00:0d:5d:0a:52:a3 513 (0x201) 42 No No 0 2
21568 64:00:f1:41:ff:de 513 (0x201) 42 No No 0 2
22304 00:b0:64:fd:1f:0a 513 (0x201) 42 No No 0 2
22368 4e:41:50:00:07:15 2050 (0x802) 6 No No 0 2
22516 78:2b:cb:1e:0a:b1 513 (0x201) 42 No No 0 2
22860 00:04:4d:da:35:c0 513 (0x201) 42 No No 0 2
23568 00:0d:5d:0a:51:f2 513 (0x201) 42 No No 0 2
23876 00:04:4d:da:55:00 513 (0x201) 42 No No 0 2
25596 00:0d:5d:0a:22:32 513 (0x201) 42 No No 0 2
26016 00:11:92:19:76:41 513 (0x201) 42 No No 0 2
26184 00:0b:be:aa:fe:85 513 (0x201) 42 No No 0 2
26228 00:0d:5d:0a:50:af 513 (0x201) 42 No No 0 2
26536 00:b0:64:fd:43:60 513 (0x201) 42 No No 0 2
26632 00:1c:c0:4b:e5:72 513 (0x201) 42 No No 0 2
26816 00:0e:83:47:6f:06 513 (0x201) 42 No No 0 2
27048 00:15:62:c9:3d:00 513 (0x201) 42 No No 0 2
27380 e8:04:62:1d:47:c0 513 (0x201) 42 No No 0 2
28088 00:12:00:42:3d:80 513 (0x201) 42 No No 0 2
28264 e0:50:bf:1c:f1:03 2049 (0x801) 2 No No 0 2
28420 00:10:7b:e8:09:b7 513 (0x201) 42 No No 0 2
28504 e0:52:2d:4c:bd:05 2049 (0x801) 0 No No 0 2
28532 00:04:4d:da:5e:40 513 (0x201) 42 No No 0 2
28668 00:0d:5d:0a:50:e6 513 (0x201) 42 No No 0 2
28888 00:1a:4b:f8:a4:34 513 (0x201) 42 No No 0 2
29104 00:04:4d:da:18:c0 513 (0x201) 42 No No 0 2
29284 00:b0:64:fd:43:50 513 (0x201) 42 No No 0 2
29412 e4:d3:f1:a5:93:78 1025 (0x401) 4 No No 0 2
29628 00:04:4d:b2:1e:80 513 (0x201) 42 No No 0 2
29696 00:0d:5d:0a:52:74 513 (0x201) 42 No No 0 2
29924 4e:41:50:00:07:12 2050 (0x802) 34 No No 0 2
30020 00:00:0c:46:e4:f8 513 (0x201) 42 No No 0 2
30316 00:1c:58:38:5a:b8 513 (0x201) 42 No No 0 2
30364 00:04:4d:b4:38:80 513 (0x201) 42 No No 0 2
31308 00:0d:5d:0a:52:ab 513 (0x201) 42 No No 0 2
31348 00:19:d1:e3:07:78 513 (0x201) 42 No No 0 2
31448 e0:52:2d:4c:bd:03 513 (0x201) 0 No No 0 2
32184 4e:41:50:00:00:01 2050 (0x802) 2 No No 0 2
32464 00:11:85:69:d0:f9 513 (0x201) 42 No No 0 2
Total table entries: 123
To display various MLAP (minimal loop avoidance protocol) details, use the show controller switch mlapcommand in the System Admin EXEC mode.
show controller switch mlap [ detail [ location node-id port-number ] | statistics [ location node-id ] | location [node-id] | reachable | trace { all | trace-name } location node-id [ all | trace-attribute ] ]
detail |
Displays detailed MLAP (minimal loop avoidance protocol) information for a single switch port. |
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot/switch notation. |
port-number |
Specifies the switch port. |
statistics |
Displays MLAP switch statistics data. |
reachable |
Lists all control plane Ethernet switches serviced by MLAP. |
trace |
Displays the MLAP trace information. |
trace-name |
Trace name. |
trace-attribute |
Trace attribute. |
Displays statistics summary for each node.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Displays MLAP information for only RPs (Router Processors).
This example shows how to display detailed MLAP information for a single switch port:
sysadmin-vm:0_RP0# show controller switch mlap detail location 0/RP0/RP-SW 2
Tue Aug 13 08:19:17.156 UTC
MLAP Summary Information For Internal Switch Port 2 (0/RP0/RP-SW)
Rack serial number: FMP12160201
Connects to: LC6
Physical port state: Down
Administrative port state: Up
Port protocol state: Down
Forwarding state: -
Protocol type: Internal
Good protocol packets sent: 0
Good protocol packets received: 0
Set VLAN requests: 0
Set VLAN responses: 0
Protocol packet send errors: 0
Protocol packet receive errors: 0
Protocol state changes: 1
MLAP Detailed Information For Internal Endpoint
Port MLAP owner: RP0
Card controlling packet path: Unknown
Peer MLAP protocol flags: Ignore-Data
Peer idle count to endpoint: 5
This active connection mask: 0x0000200000800006
Peer active connection mask: 0x0000000000000000
Connected endpoint card type: Unknown
.
.
.
To list all control plane Ethernet switches to which connectivity is established, use the show controller switch reachable command in the System Admin EXEC mode.
show controller switch reachable
This command has no keywords or arguments.
None
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Use this command to verify connectivity between various nodes in the system.
This example shows how to list the control place Ethernet switches:
sysadmin-vm:0_RP0#show controller switch reachable
Rack Card Switch
--------------------
0 RP0 RP-SW
0 RP1 RP-SW
0 LC3 LC-SW
To display the control plane Ethernet port statistics information specific to an SDR, use the show controller switch sdr command in the System Admin EXEC mode.
show controller switch sdr { 1 | 2 } port-statistics location [node-id]
sdr 1 |
Indicates the admin plane. |
sdr 2 |
Indicates the first SDR created in the system. By default, the value for sdr 2 is default-sdr. |
port-statistics |
Displays the SDR port statistics. |
location node-id |
Selects the target location. The node-id argument is expressed in the rack/slot/switch notation. |
Displays information for all the nodes.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
sysadmin-vm:0_RP0#show controller switch sdr 1 port-statistics location 0/LC3/LC-SW
Tue Aug 13 05:17:04.962 UTC
Switch Traffic Packet Traffic
Port Type Direction Class Conforming Exceeding Dropped
---------------------------------------------------------------------
0 IPC Rx 0 1113702 0 0
1 0 0 0
2 0 0 0
3 0 0 0
4 0 0 0
5 0 0 0
6 0 0 0
7 87755 0 0
Tx - 3493443 0 0
MgmtEth Rx 0 0 0 0
1 0 0 0
2 0 0 0
3 0 0 0
4 0 0 0
5 0 0 0
6 0 0 0
7 0 0 0
Tx - 1507838 0 0
2 IPC Rx 0 1282246 0 0
1 0 0 0
--More--
To display the SDR global-statistics summary, use the show controller switch sdr global-statistics command in the System Admin EXEC mode.
show controller switch sdr global-statistics location [node-id]
location node-id |
Selects the target location. The node-id argument is expressed in the rack/slot/switch notation. |
Displays information for all nodes.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
sysadmin-vm:0_RP0#show controller switch sdr global-statistics location 0/LC3/LC-SW
Tue Aug 13 05:43:51.230 UTC
Traffic Traffic
SDR ID SDR Name Type Class Conforming Exceeding Dropped
-----------------------------------------------------------------------
1 Calvados IPC 0 1473518 0 0
1 0 0 0
2 0 0 0
3 0 0 0
4 0 0 0
5 0 0 0
6 0 0 0
7 2573111 0 0
MgmtEth 0 1534353 0 0
1 0 0 0
2 0 0 0
3 0 0 0
4 0 0 0
5 0 0 0
6 0 0 0
7 0 0 0
2 default-sdr IPC 0 6904586 0 0
1 0 0 0
2 0 0 0
3 0 0 0
--More--
To display the SDR policers summary, use the show controller switch sdr policers command in the System Admin EXEC mode.
show controller switch sdr policers location [node-id]
location node-id |
Selects the target location. The node-id argument is expressed in the rack/slot/switch notation. |
Displays information for all nodes.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
To display CoS (class of service) parameters for an SDR, use this command.
sysadmin-vm:0_RP0#show controller switch sdr policers location 0/LC3/LC-SW
Tue Aug 13 06:02:04.950 UTC
controller switch sdr policers location 0/LC3/LC-SW
Summary Policer Information for Switch 0/LC3/LC-SW
Port Policing Enabled: Yes
Port Committed Burst Size (bytes): 102400
Port Peak Burst Size (bytes): 204800
Port Policer MRU (bytes): 10240
Global Policing Enabled: No
Global Committed Burst Size (bytes): 102400
Global Peak Burst Size (bytes): 204800
Global Policer MRU (bytes): 10240
SDR SDR CoS CoS CoS CoS CoS CoS CoS CoS CoS
SDR ID SDR Name CIR(%) PIR(%) B/W 0(%) 1(%) 2(%) 3(%) 4(%) 5(%) 6(%) 7(%)
------------------------------------------------------------------------------------------
1 Calvados 20 90 CIR 20 5 5 10 10 10 20 20
PIR 100 50 50 50 100 100 100 100
2 default-sdr 40 90 CIR 20 5 5 10 10 10 20 20
To display the SDR port-statistics summary, use the show controller switch sdr port-statistics command in the System Admin EXEC mode.
show controller switch sdr port-statistics location [node-id] [port-number]
location node-id |
Selects the target location. The node-id argument is expressed in the rack/slot/switch notation. |
port-number |
Displays SDR port-statistics of the specified port. |
Displays information for all the nodes.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Use this command to display packet statistics for each of the traffic class.
sysadmin-vm:0_RP0#show controller switch sdr port-statistics location 0/LC3/LC-SW
Tue Aug 13 06:18:01.250 UTC
Switch SDR Traffic Packet
Port ID SDR Name Type Direction Conforming Exceeding Dropped
------------------------------------------------------------------------------
0 1 Calvados IPC Rx 1215851 0 0
Tx 3531794 0 0
MgmtEth Rx 0 0 0
Tx 1525602 0 0
2 default-sdr IPC Rx 6153150 0 0
Tx 8294939 0 0
MgmtEth Rx 0 0 0
Tx 0 0 0
2 1 Calvados IPC Rx 3532095 0 0
Tx 2349934 0 0
2 default-sdr IPC Rx 8294945 0 0
Tx 6153144 0 0
4 1 Calvados IPC Rx 809583 0 0
Tx 809583 0 0
2 default-sdr IPC Rx 0 0 0
Tx 0 0 0
6 2 default-sdr IPC Rx 0 0 0
Tx 0 0 0
8 1 Calvados IPC Rx 1134092 0 0
Tx 2559058 0 0
--More--
To display the SFP (Small Form-Factor Pluggable) information, use the show controller switch sfp command in the System Admin EXEC mode.
show controller switch sfp { detail location node-id port-number | summary location [node-id] [port-number] }
detail |
Displays the SFP information in detail. |
port-number |
Displays the SFP information of the specified port. Range is from 0 to 59. |
summary |
Displays the summary of SFP information. |
location node-id |
Selects the target location. The node-id argument is expressed in the rack/slot/switch notation. |
If node-id is not specified for the show controller switch sfp summary location command, then the information for all the nodes is displayed.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
SFPs are supported only on the RP (Route Processors).
sysadmin-vm:0_RP0#show controller switch sfp detail location 0/RP0/RP-SW 54
Fri Aug 30 19:49:58.155 UTC
SFP EEPROM Data for Switch Port 54
Transceiver Type: SFP
Transceiver Code: SFP-1G-LX
Encoding: 8B/10B
Bit Rate (Mbps): 1300
Link Reach for 9u Fiber (kilometers): 10
Link Reach for 9u Fiber (meters): 10000
Link Reach for 50u (OM2) Fiber (meters): 550
Link Reach for 62.5u (OM1) Fiber (meters): 550
Vendor Name: CISCO-FINISAR
Vendor OUI: 00.90.65
Vendor Part #: FTLF1318P2BCL-CS (Rev. 0000)
Laser Wavelength (nano-meters): 1310
Implemented Options: LOS,TxDisable
Vendor Serial #: FNS11250BP3
Date Code (yy/mm/dd): 07/06/18 (lot code: )
Diagnostic Monitoring: AvePwrMon
Enhanced Options:
SFP MSA Data
0x0000: 03 04 07 00 00 00 02 00 : 00 00 00 01 0D 00 0A 64 ...............d
0x0010: 37 37 00 00 43 49 53 43 : 4F 2D 46 49 4E 49 53 41 77..CISCO.FINISA
0x0020: 52 20 20 20 00 00 90 65 : 46 54 4C 46 31 33 31 38 R......eFTLF1318
0x0030: 50 32 42 43 4C 2D 43 53 : 30 30 30 30 05 1E 00 EB P2BCL.CS0000....
0x0040: 00 12 00 00 46 4E 53 31 : 31 32 35 30 42 50 33 20 ....FNS11250BP3.
0x0050: 20 20 20 20 30 37 30 36 : 31 38 20 20 08 00 00 D5 ....070618......
Threshold Data
Temperature
Alarm High: -0.004 C
Warning High: -0.004 C
Warning Low: -0.004 C
Alarm Low: -0.004 C
Voltage
Alarm High: 6.554 Volt
Warning High: 6.554 Volt
Warning Low: 6.554 Volt
Alarm Low: 6.554 Volt
Bias
Alarm High: 131.070 mAmps
Warning High: 131.070 mAmps
Warning Low: 131.070 mAmps
Alarm Low: 131.070 mAmps
Tx Power
Alarm High: 6.554 mW (8.16 dBm)
Warning High: 6.554 mW (8.16 dBm)
Warning Low: 6.554 mW (8.16 dBm)
Alarm Low: 6.554 mW (8.16 dBm)
Rx Power
Alarm High: 6.554 mW (8.16 dBm)
Warning High: 6.554 mW (8.16 dBm)
Warning Low: 6.554 mW (8.16 dBm)
Alarm Low: 6.554 mW (8.16 dBm)
Real Time Data
Temperature: -0.004 C
Voltage: 6.554 Volt
Bias: 131.070 mAmps
Tx Power: 6.554 mW (8.16 dBm)
Rx Power: 6.554 mW (8.16 dBm)
Current Status/Control: DataReadyBar,RxLOS,TxFault,SoftRateSel0Eq1,RateSel0Eq1,RateSel1Eq1,SoftTxDisable,TxDisable
SFP A2 Data [Lower]
0x0000: FF FF FF FF FF FF FF FF : FF FF FF FF FF FF FF FF ................
0x0010: FF FF FF FF FF FF FF FF : FF FF FF FF FF FF FF FF ................
0x0020: FF FF FF FF FF FF FF FF : FF FF FF FF FF FF FF FF ................
0x0030: FF FF FF FF FF FF FF FF : FF FF FF FF FF FF FF FF ................
0x0040: FF FF FF FF FF FF FF FF : FF FF FF FF FF FF FF FF ................
0x0050: FF FF FF FF FF FF FF FF : FF FF FF FF FF FF FF FF ................
0x0060: FF FF FF FF FF FF FF FF : FF FF FF FF FF FF FF FF ................
0x0070: FF FF FF FF FF FF FF FF : FF FF FF FF FF FF FF FF ................
Cisco SFP Information
CLEI Code: CN8ID42AAA
Part Number: 30-1299-01 (ver: V01 )
Minimum Temperature (C): 251
Maximum Temperature (C): 70
Product Id: GLC-LH-SM
SFP A2 Data [Upper]
0x0080: 43 4E 38 49 44 34 32 41 : 41 41 33 30 2D 31 32 39 CN8ID42AAA30.129
0x0090: 39 2D 30 31 56 30 31 20 : 4B FB 46 00 00 00 00 D5 9.01V01.K.F.....
0x00A0: 00 00 00 00 00 00 00 00 : 00 00 00 00 00 00 00 00 ................
0x00B0: 00 00 00 00 00 00 00 00 : 00 00 00 00 00 00 AA AA ................
0x00C0: 47 4C 43 2D 4C 48 2D 53 : 4D 20 20 20 20 20 20 20 GLC.LH.SM.......
0x00D0: 20 20 20 20 20 20 20 20 : 20 20 20 20 20 20 20 24 ................
0x00E0: 00 00 00 00 00 00 00 00 : 00 00 00 00 00 00 00 00 ................
0x00F0: 00 00 00 00 00 00 00 00 : 00 40 00 40 00 00 00 00 ................
To display switch statistics, use the show controller switch statistics command in the System Admin EXEC mode.
show controller switch statistics { detail [ location node-id port-number ] | location [node-id] [port-number] }
detail |
Displays detailed switch port statistics. |
location node-id |
Specifies the location from which to display information. The node-id argument is expressed in the rack/slot/switch notation. |
port-number |
Displays switch statistics of the specified port. Range is from 0 to 59. |
If node-id is not specified for the show controller switch statistics location command, then the information for all the nodes is displayed.
Also, if the show controller switch statistics detail command is used without the location keyword, then the information for all the ports on all the nodes is displayed.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
This command displays statistics for all the internal ports present in the Ethernet switch. It also displays connectivity information between each switch port and nodes in the system.
sysadmin-vm:0_RP0# show controller switch statistics location 0/RP0/RP-SW
Thu Aug 29 12:17:32.631 UTC
Rack Card Switch Rack Serial Number
--------------------------------------
0 RP0 RP-SW FMP12160201
Phys State Tx Rx Tx Rx
Port State Changes Packets Packets Errors Errors Connects To
-----------------------------------------------------------------------------
0 Down 1 0 0 0 0 LC7
2 Down 1 0 0 0 0 LC6
4 Up 1 2209750 1783057 0 0 FC0
5 Down 0 0 0 0 0 FC1
6 Down 1 0 0 0 0 LC5
8 Down 1 0 0 0 0 LC4
10 Down 0 0 0 0 0 FC2
16 Down 1 0 0 0 0 LC0
18 Down 1 0 0 0 0 LC1
20 Down 0 0 0 0 0 FC5
21 Down 0 0 0 0 0 FC4
22 Down 1 0 0 0 0 LC2
24 Up 11 1474511 913984 0 0 LC3
26 Down 0 0 0 0 0 FC3
32 Up 11 2219574 1788393 0 0 RP1 Card (RP0 Ctrl)
34 Up 11 142616 142622 0 0 RP1 Card (RP1 Ctrl)
sysadmin-vm:0_RP0#show controller switch statistics detail location 0/RP0/RP-SW 2
Phys Port
Rack Card Switch Port State Speed Connects To
-----------------------------------------------------
0 RP0 RP-SW 2 Down 10-Gbps LC6
Rx Unicast Packets: 0
Rx Multicast Packets: 0
Rx Broadcast Packets: 0
Rx Flow Control: 0
Rx Good Octets: 0
Rx Bad Octets: 0
Rx FIFO Overrun: 0
Rx Undersize: 0
Rx Fragments: 0
Rx Oversize: 0
Rx Jabber: 0
Rx Errors: 0
Rx Bad CRC: 0
Rx Collisions: 0
Tx Unicast Packets: 0
Tx Multicast Packets: 0
Tx Broadcast Packets: 0
--More--
To display the switch status summary, use the show controller switch summary command in the System Admin EXEC mode.
show controller switch summary [ location [node-id] [port-number] ]
location node-id |
Selects the target location. The node-id argument is expressed in the rack/slot/switch notation. |
port-number |
Displays switch status summary of the specified port. |
Displays information for all the nodes.
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
This command is used to display the status of each port on the switch.
sysadmin-vm:0_RP0#show controller switch summary location 0/RP0/RP-SW
Fri Aug 16 06:05:56.205 UTC
Rack Card Switch Rack Serial Number
--------------------------------------
0 RP0 RP-SW FMP12160201
Phys Admin Port Protocol Forward
Port State State Speed State State Connects To
------------------------------------------------------------------------
0 Down Up 10-Gbps Down - LC7
2 Down Up 10-Gbps Down - LC6
4 Up Up 1-Gbps Active Forwarding FC0
5 Down Up 1-Gbps Down - FC1
6 Down Up 10-Gbps Down - LC5
8 Down Up 10-Gbps Down - LC4
10 Down Up 1-Gbps Down - FC2
16 Down Up 10-Gbps Down - LC0
18 Down Up 10-Gbps Down - LC1
20 Down Up 1-Gbps Down - FC5
21 Down Up 1-Gbps Down - FC4
22 Down Up 10-Gbps Down - LC2
24 Up Up 10-Gbps Active Forwarding LC3
26 Down Up 1-Gbps Down - FC3
32 Up Up 10-Gbps Active Forwarding RP1 Card (RP0 Ctrl)
34 Up Up 10-Gbps - Forwarding RP1 Card (RP1 Ctrl)
--More--
To display the switch trace information, use the show controller switch trace command in the System Admin EXEC mode.
show controller switch trace { all | trace-name } location node-id [ all | trace-attribute ]
trace-name |
Trace name. |
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot notation. |
trace-attribute |
Trace attribute. |
all |
Displays all the details. |
None
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Used for diagnostics only.
sysadmin-vm:0_RP0#show controller switch trace system_event location 0/RP0 all
Sat Sep 14 05:52:52.133 UTC
02.58.39.459393536:* *** Starting ESD *** *
02.58.39.459511168:Init: Basic initialization complete. Entering main event hand ler
02.58.42.114090368:Event: CCC cardinfo: ESD personality configured as RP0 (cmdli ne ignored)
02.58.42.114091648:Event: CCC cardinfo: platform set as Production Panini
02.58.42.114172800:INV: Skip starting of the RP switch till chassis info is rece ived.
02.58.42.114238336:INV: In Non-dual router mode
02.58.42.114239232:INV: Starting RP switch from chassisinfo_cb.
02.58.42.215374208:Event: CCC information received. Start switch
02.58.42.255279360:CCC PON: flag (0x1) indicates PON will program Black Vlan tra nslations for all SDR's
02.58.42.270560768:HWID:Board Type 0x1e0800 SLOT:0 HWID:|3c08:3_10.0
02.58.42.270562432:HWID:Board Type 0x1e0800 SLOT:0 HWID:|3c08:3_11.0
02.58.42.270562944:HWID:Board Type 0x1e0800 SLOT:0 HWID:|3c08:3_12.0
02.58.42.270563456:HWID:Board Type 0x1e0800 SLOT:0 HWID:|3c08:3_13.0
02.58.44.112152704:Event: Switch Status Online. Init CPSS and config switch
02.58.44.112175488:Init: Switch is capable of hotplug and reset
02.58.44.112237056:Reg read for is_restart, reg 0x2800c1c, data 0x0
02.58.44.112240512:Init: Is NOT RESTART
02.58.44.112242304:SPI: Version read from flash 1.32
02.58.44.112242688:SPI: Version: OK 1.32
02.58.44.112248960:CPSS HA: Is ENABLED. Start HA recovery
02.58.44.324463616:CPSS HA: Recovery complete
02.58.44.326155136:Info: CPSS Version: CPSS 4.0.2 Release
02.58.44.326188288:Info: Switch Device Information
Type : 0xE01F11AB
Revision : 3
Family : 14
Max port num : 59
02.58.44.375312512:Init: CPSS initialization done. Start switch configutation
02.58.44.375330048:Init: Last exit was due to power cycle or unknown reason
02.58.44.375524096:Init: Before cpps based switch init, Global Config Register 0x58, 0x881e4003
02.58.44.379397888:SPI: Data verify OK: Config Verify Calv Black Vlan Xlate: OK
02.58.44.380258816:SPI: Data verify OK: existing config OK: expected Calv vlans exist on ports
02.58.44.470336384:SPI: Existing SPI based switch initial config is OK
02.58.44.471564032:Init: TXQ Config is ENABLED. Init OK
--More--
To display the control plane Ethernet VLAN information, use the show controller switch vlan command in the System Admin EXEC mode.
show controller switch vlan { [vlan-id] location [node-id] | information location [node-id] | membership location [node-id] | rules location [node-id] [port-number] }
vlan-id |
Specifies the VLAN ID. |
information |
Displays the allocated VLANs for each SDR. |
membership |
Lists the switch port membership of VLANs. |
rules |
Displays VLAN rule summary. |
port-number |
Displays VLAN rule information of the specified port. |
location node-id |
Specifies the target location. The node-id argument is expressed in the rack/slot/switch notation. |
None
System Admin EXEC
Release | Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Use this command to view the VLANs allocated to an SDR.
sysadmin-vm:0_RP0#show controller switch vlan information location 0/LC3/LC-SW
Fri Aug 16 10:03:17.881 UTC
SDR
Identifier SDR Name VLAN VLAN Use
-----------------------------------------------------------------
1 Calvados 513 (0x201) Calvados Management
1025 (0x401) Calvados RP1 Hosted IPC
2049 (0x801) Calvados RP0 Hosted IPC
2 default-sdr 1026 (0x402) SDR 2 RP1 Hosted IPC
2050 (0x802) SDR 2 RP0 Hosted IPC