Cisco IOS XR Interface and Hardware Component Configuration Guide for the Cisco CRS Router, Release 4.3.x
Configuring Ethernet OAM on Cisco IOS XR Software
Downloads: This chapterpdf (PDF - 1.69MB) The complete bookPDF (PDF - 7.89MB) | Feedback

Configuring Ethernet OAM on Cisco IOS XR Software

Table Of Contents

Configuring Ethernet OAM on Cisco IOS XR Software

Contents

Prerequisites for Configuring Ethernet OAM

Restrictions for Configuring Ethernet OAM

Information About Configuring Ethernet OAM

Ethernet Link OAM

Neighbor Discovery

Link Monitoring

MIB Retrieval

Miswiring Detection (Cisco-Proprietary)

SNMP Traps

Ethernet CFM

Maintenance Domains

Services

Maintenance Points

CFM Protocol Messages

MEP Cross-Check

Configurable Logging

EFD

Ethernet SLA

Y.1731 Performance Monitoring

Loss Measurement Terminology

Ethernet SLA Concepts

Statistics Measurement and Ethernet SLA Operations Overview

Configuration Overview of Scheduled Ethernet SLA Operations

How to Configure Ethernet OAM

Configuring Ethernet Link OAM

Configuring an Ethernet OAM Profile

Attaching an Ethernet OAM Profile to an Interface

Configuring Ethernet OAM at an Interface and Overriding the Profile Configuration

Verifying the Ethernet OAM Configuration

Configuring Ethernet CFM

Configuring a CFM Maintenance Domain

Configuring Services for a CFM Maintenance Domain

Enabling and Configuring Continuity Check for a CFM Service

Configuring Automatic MIP Creation for a CFM Service

Configuring Cross-Check on a MEP for a CFM Service

Configuring Other Options for a CFM Service

Configuring CFM MEPs

Configuring Y.1731 AIS

Configuring EFD for a CFM Service

Verifying the CFM Configuration

Troubleshooting Tips

Configuring Ethernet SLA

Ethernet SLA Configuration Guidelines

Configuring an SLA Operation Profile

Configuring SLA Probe Parameters in a Profile

Configuring SLA Statistics Measurement in a Profile

Configuring a Schedule for an SLA Operation Probe in a Profile

Configuring an SLA Operation

Configuring an On-Demand SLA Operation

Verifying SLA Configuration

Configuration Examples for Ethernet OAM

Configuration Examples for EOAM Interfaces

Configuring an Ethernet OAM Profile Globally: Example

Configuring Ethernet OAM Features on an Individual Interface: Example

Configuring Ethernet OAM Features to Override the Profile on an Individual Interface: Example

Clearing Ethernet OAM Statistics on an Interface: Example

Enabling SNMP Server Traps on a Router: Example

Configuration Examples for Ethernet CFM

Ethernet CFM Domain Configuration: Example

Ethernet CFM Service Configuration: Example

Continuity Check for an Ethernet CFM Service Configuration: Example

MIP Creation for an Ethernet CFM Service Configuration: Example

Cross-check for an Ethernet CFM Service Configuration: Example

Other Ethernet CFM Service Parameter Configuration: Example

MEP Configuration: Example

Ethernet CFM Show Command: Examples

AIS for CFM Configuration: Examples

AIS for CFM Show Commands: Examples

EFD Configuration: Examples

Displaying EFD Information: Examples

Configuration Examples for Ethernet SLA

Ethernet SLA Profile Type Configuration: Examples

Ethernet SLA Probe Configuration: Examples

Profile Statistics Measurement Configuration: Examples

Scheduled SLA Operation Probe Configuration: Examples

Ethernet SLA Operation Probe Scheduling and Aggregation Configuration: Example

Ongoing Ethernet SLA Operation Configuration: Example

On-Demand Ethernet SLA Operation Basic Configuration: Examples

Ethernet SLA Y.1731 SLM Configuration: Examples

Ethernet SLA Show Commands: Examples

Where to Go Next

Additional References

Related Documents

Standards

MIBs

RFCs

Technical Assistance


Configuring Ethernet OAM on Cisco IOS XR Software


This module describes the configuration of Ethernet Operations, Administration, and Maintenance (OAM) on the Cisco CRS-1 Router.

Feature History for Configuring Ethernet OAM

Release
Modification

Release 3.9.0

Support for the following features was introduced:

Ethernet Link OAM

Ethernet CFM

Release 3.9.1

Support for the following features was introduced:

EFD

AIS

The ethernet cfm mep domain command is replaced by the ethernet cfm and mep domain commands.

Release 4.0.0

Support for the following features was introduced:

The action link-fault command is replaced by the action uni-directional link fault command.

The efd keyword is added as an option to the following commands:

action capabilities-conflict

action discovery-timeout

action session-down

action uni-directional link-fault

Support for the Ethernet SLA feature was introduced, including some new areas of SLA support in Cisco IOS XR software including:

Support for on-demand Ethernet SLA operations using the ethernet sla on-demand operation command.

One-way delay and jitter measurements using the following new keyword options for the statistics measure command: one-way-delay-ds. one-way-delay-sd. one-way-jitter-ds. one-way-jitter-sd

Specification of a test pattern to pad loopback packets when measuring delay.

Displaying the time when the minimum (Min) and maximum (Max) values of a statistic occurred in the measurement time period in the show ethernet sla statistics detail command.

Release 4.1.0

Support for CFM Y.1731 ITU Carrier Code (ICC)-based MEG ID (MAID) format was introduced.

Release 4.3.0

Support for ITU-T Y.1731 Synthetic Loss Measurement was introduced.

Release 4.3.1

Support for ITU-T Y.1731 Loss Measurement was introduced.


Contents

Prerequisites for Configuring Ethernet OAM

Restrictions for Configuring Ethernet OAM

Information About Configuring Ethernet OAM

How to Configure Ethernet OAM

Configuration Examples for Ethernet OAM

Where to Go Next

Additional References

Prerequisites for Configuring Ethernet OAM

You must be in a user group associated with a task group that includes the proper task IDs. The command reference guides include the task IDs required for each command. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Before configuring Ethernet OAM, confirm that at least one of the Gigabit Ethernet line cards supported on the router is installed:

4-Port Gigabit Ethernet physical layer interface module (PLIM)

8-Port 10-Gigabit Ethernet PLIM

4-Port 10-Gigabit Ethernet PLIM

2-Port Gigabit Ethernet SPA

5-Port Gigabit Ethernet SPA

8-Port Gigabit Ethernet SPA

10-Port Gigabit Ethernet SPA

1-Port 10-Gigabit Ethernet SPA

1-Port 10-Gigabit Ethernet WAN SPA

Restrictions for Configuring Ethernet OAM

The following functional areas of Ethernet OAM are not supported on the Cisco CRS-1 Router in Cisco IOS XR Release 4.1:

Hello interval configuration

Remote loopback

Unidirectional link-fault detection

Information About Configuring Ethernet OAM

To configure Ethernet OAM, you should understand the following concepts:

Ethernet Link OAM

Ethernet CFM

Ethernet SLA

Ethernet Link OAM

Ethernet as a Metro Area Network (MAN) or a Wide Area Network (WAN) technology benefits greatly from the implementation of Operations, Administration and Maintenance (OAM) features. Ethernet link OAM features allow Service Providers to monitor the quality of the connections on a MAN or WAN. Service providers can monitor specific events, take actions on events, and if necessary, put specific interfaces into loopback mode for troubleshooting. Ethernet link OAM operates on a single, physical link and it can be configured to monitor either side or both sides of that link.

Ethernet link OAM can be configured in the following ways:

A Link OAM profile can be configured, and this profile can be used to set the parameters for multiple interfaces.

Link OAM can be configured directly on an interface.

When an interface is also using a link OAM profile, specific parameters that are set in the profile can be overridden by configuring a different value directly on the interface.

An EOAM profile simplifies the process of configuring EOAM features on multiple interfaces. An Ethernet OAM profile, and all of its features, can be referenced by other interfaces, allowing other interfaces to inherit the features of that Ethernet OAM profile.

Individual Ethernet link OAM features can be configured on individual interfaces without being part of a profile. In these cases, the individually configured features always override the features in the profile.

The preferred method of configuring custom EOAM settings is to create an EOAM profile in Ethernet configuration mode and then attach it to an individual interface or to multiple interfaces.

The following standard Ethernet Link OAM features are supported on the router:

Neighbor Discovery

Link Monitoring

MIB Retrieval

Miswiring Detection (Cisco-Proprietary)

SNMP Traps

Neighbor Discovery

Neighbor discovery enables each end of a link to learn the OAM capabilities of the other end and establish an OAM peer relationship. Each end also can require that the peer have certain capabilities before it will establish a session. You can configure certain actions to be taken if there is a capabilities conflict or if a discovery process times out, using the action capabilities-conflict or action discovery-timeout commands.

Link Monitoring

Link monitoring enables an OAM peer to monitor faults that cause the quality of a link to deteriorate over time. When link monitoring is enabled, an OAM peer can be configured to take action when the configured thresholds are exceeded.

MIB Retrieval

MIB retrieval enables an OAM peer on one side of an interface to get the MIB variables from the remote side of the link. The MIB variables that are retrieved from the remote OAM peer are READ ONLY.

Miswiring Detection (Cisco-Proprietary)

Miswiring Detection is a Cisco-proprietary feature that uses the 32-bit vendor field in every Information OAMPDU to identify potential miswiring cases.

SNMP Traps

SNMP traps can be enabled or disabled on an Ethernet OAM interface.

Ethernet CFM

Ethernet Connectivity Fault Management (CFM) is a service-level OAM protocol that provides tools for monitoring and troubleshooting end-to-end Ethernet services per VLAN. This includes proactive connectivity monitoring, fault verification, and fault isolation. CFM uses standard Ethernet frames and can be run on any physical media that is capable of transporting Ethernet service frames. Unlike most other Ethernet protocols which are restricted to a single physical link, CFM frames can transmit across the entire end-to-end Ethernet network.

CFM is defined in two standards:

IEEE 802.1ag—Defines the core features of the CFM protocol.

ITU-T Y.1731—Redefines, but maintains compatibility with the features of IEEE 802.1ag, and defines some additional features.

Ethernet CFM on the Cisco CRS-1 Router supports these functions of ITU-T Y.1731:

ETH-CC, ETH-RDI, ETH-LB, ETH-LT—These are equivalent to the corresponding features defined in IEEE 802.1ag.


Note The Linktrace responder procedures defined in IEEE 802.1ag are used rather than the procedures defined in Y.1731; however, these are interoperable.


ETH-AIS—The reception of ETH-LCK messages is also supported.

ETH-DM, ETH-SLM—This is supported with the Ethernet SLA feature. For more information about Ethernet SLA, see the "Ethernet SLA" section.

To understand how the CFM maintenance model works, you need to understand the following concepts and features:

Maintenance Domains

Services

Maintenance Points

CFM Protocol Messages

MEP Cross-Check

Configurable Logging

EFD

Maintenance Domains

A maintenance domain describes a management space for the purpose of managing and administering a network. A domain is owned and operated by a single entity and defined by the set of interfaces internal to it and at its boundary, as shown in Figure 1.

Figure 1 CFM Maintenance Domain

A maintenance domain is defined by the bridge ports that are provisioned within it. Domains are assigned maintenance levels, in the range of 0 to 7, by the administrator. The level of the domain is useful in defining the hierarchical relationships of multiple domains.

CFM maintenance domains allow different organizations to use CFM in the same network, but independently. For example, consider a service provider who offers a service to a customer, and to provide that service, they use two other operators in segments of the network. In this environment, CFM can be used in the following ways:

The customer can use CFM between their CE devices, to verify and manage connectivity across the whole network.

The service provider can use CFM between their PE devices, to verify and manage the services they are providing.

Each operator can use CFM within their operator network, to verify and manage connectivity within their network.

Each organization uses a different CFM maintenance domain.

Figure 2 shows an example of the different levels of maintenance domains in a network.


Note In CFM diagrams, the conventions are that triangles represent MEPs, pointing in the direction that the MEP sends CFM frames, and circles represent MIPs. For more information about MEPs and MIPs, see the "Maintenance Points" section.


Figure 2 Different CFM Maintenance Domains Across a Network

To ensure that the CFM frames for each domain do not interfere with each other, each domain is assigned a maintenance level, between 0 and 7. Where domains are nested, as in this example, the encompassing domain must have a higher level than the domain it encloses. In this case, the domain levels must be negotiated between the organizations involved. The maintenance level is carried in all CFM frames that relate to that domain.

CFM maintenance domains may touch or nest, but cannot intersect. Figure 3 illustrates the supported structure for touching and nested domains, and the unsupported intersection of domains.

Figure 3 Supported CFM Maintenance Domain Structure

Services

A CFM service allows an organization to partition its CFM maintenance domain, according to the connectivity within the network. For example, if the network is divided into a number of virtual LANs (VLANs), a CFM service is created for each of these. CFM can then operate independently in each service. It is important that the CFM services match the network topology, so that CFM frames relating to one service cannot be received in a different service. For example, a service provider may use a separate CFM service for each of their customers, to verify and manage connectivity between that customer's end points.

A CFM service is always associated with the maintenance domain that it operates within, and therefore with that domain's maintenance level. All CFM frames relating to the service carry the maintenance level of the corresponding domain.


Note CFM Services are referred to as Maintenance Associations in IEEE 802.1ag and as Maintenance Entity Groups in ITU-T Y.1731.


Maintenance Points

A CFM Maintenance Point (MP) is an instance of a particular CFM service on a specific interface. CFM only operates on an interface if there is a CFM maintenance point on the interface; otherwise, CFM frames are forwarded transparently through the interface.

A maintenance point is always associated with a particular CFM service, and therefore with a particular maintenance domain at a particular level. Maintenance points generally only process CFM frames at the same level as their associated maintenance domain. Frames at a higher maintenance level are always forwarded transparently, while frames at a lower maintenance level are normally dropped. This helps enforce the maintenance domain hierarchy described in the "Maintenance Domains" section, and ensures that CFM frames for a particular domain cannot leak out beyond the boundary of the domain.

There are two types of MP:

Maintenance End Points (MEPs)—Created at the edge of the domain. Maintenance end points (MEPs) are members of a particular service within a domain and are responsible for sourcing and sinking CFM frames. They periodically transmit continuity check messages and receive similar messages from other MEPs within their domain. They also transmit traceroute and loopback messages at the request of the administrator. MEPs are responsible for confining CFM messages within the domain.

Maintenance Intermediate Points (MIPs)—Created in the middle of the domain. Unlike MEPS, MIPs do allow CFM frames at their own level to be forwarded.

MIP Creation

Unlike MEPs, MIPs are not explicitly configured on each interface. MIPs are created automatically according to the algorithm specified in the CFM 802.1ag standard. The algorithm, in brief, operates as follows for each interface:

The cross-connect for the interface is found, and all services associated with that cross-connect are considered for MIP auto-creation.

The level of the highest-level MEP on the interface is found. From among the services considered above, the service in the domain with the lowest level that is higher than the highest MEP level is selected. If there are no MEPs on the interface, the service in the domain with the lowest level is selected.

The MIP auto-creation configuration (mip auto-create command) for the selected service is examined to determine whether a MIP should be created.


Note Configuring a MIP auto-creation policy for a service does not guarantee that a MIP will automatically be created for that service. The policy is only considered if that service is selected by the algorithm first.


MEP and CFM Processing Overview

The boundary of a domain is an interface, rather than a bridge or host. Therefore, MEPs can be sub-divided into two categories:

Down MEPs—Send CFM frames from the interface where they are configured, and process CFM frames received on that interface. Down MEPs transmit AIS messages upward (toward the cross-connect).

Up MEPs—Send frames into the bridge relay function, as if they had been received on the interface where the MEP is configured. They process CFM frames that have been received on other interfaces, and have been switched through the bridge relay function as if they are going to be sent out of the interface where the MEP is configured. Up MEPs transmit AIS messages downward (toward the wire). However, AIS packets are only sent when there is a MIP configured on the same interface as the MEP and at the level of the MIP.


Note The terms Down MEP and Up MEP are defined in the IEEE 802.1ag and ITU-T Y.1731 standards, and refer to the direction that CFM frames are sent from the MEP. The terms should not be confused with the operational status of the MEP.


Figure 4 illustrates the monitored areas for Down and Up MEPs.

Figure 4 Monitored Areas for Down and Up MEPs

Figure 5 shows maintenance points at different levels. Because domains are allowed to nest but not intersect (see Figure 3), a MEP at a low level always corresponds with a MEP or MIP at a higher level. In addition, only a single MIP is allowed on any interface—this is generally created in the lowest domain that exists at the interface and that does not have a MEP.

Figure 5 CFM Maintenance Points at Different Levels

MIPs and Up MEPs can only exist on switched (Layer 2) interfaces, because they send and receive frames from the bridge relay function. Down MEPs can be created on switched (Layer 2) or routed (Layer 3) interfaces.

MEPs continue to operate normally if the interface they are created on is blocked by the Spanning Tree Protocol (STP); that is, CFM frames at the level of the MEP continue to be sent and received, according to the direction of the MEP. MEPs never allow CFM frames at the level of the MEP to be forwarded, so the STP block is maintained.

MIPs also continue to receive CFM frames at their level if the interface is STP blocked, and can respond to any received frames. However, MIPs do not allow CFM frames at the level of the MIP to be forwarded if the interface is blocked.


Note A separate set of CFM maintenance levels is created every time a VLAN tag is pushed onto the frame. Therefore, if CFM frames are received on an interface which pushes an additional tag, so as to "tunnel" the frames over part of the network, the CFM frames will not be processed by any MPs within the tunnel, even if they are at the same level. For example, if a CFM MP is created on an interface with an encapsulation that matches a single VLAN tag, any CFM frames that are received at the interface that have two VLAN tags will be forwarded transparently, regardless of the CFM level.


CFM Protocol Messages

The CFM protocol consists of a number of different message types, with different purposes. All CFM messages use the CFM EtherType, and carry the CFM maintenance level for the domain to which they apply.

This section describes the following CFM messages:

Continuity Check (IEEE 802.1ag and ITU-T Y.1731)

Loopback (IEEE 802.1ag and ITU-T Y.1731)

Linktrace (IEEE 802.1ag and ITU-T Y.1731)

Exploratory Linktrace (Cisco)

Alarm Indication Signal (ITU-T Y.1731)

Delay and Jitter Measurement (ITU-T Y.1731)

Synthetic Loss Measurement (ITU-T Y.1731)

Loss Measurement (ITU-T Y.1731)

Continuity Check (IEEE 802.1ag and ITU-T Y.1731)

Continuity Check Messages (CCMs) are "heartbeat" messages exchanged periodically between all the MEPs in a service. Each MEP sends out multicast CCMs, and receives CCMs from all the other MEPs in the service—these are referred to as peer MEPs. This allows each MEP to discover its peer MEPs, and to verify that there is connectivity between them.

MIPs also receive CCMs. MIPs use the information to build a MAC learning database that is used when responding to Linktrace. For more information about Linktrace, see the "Linktrace (IEEE 802.1ag and ITU-T Y.1731)" section.

Figure 6 Continuity Check Message Flow

All the MEPs in a service must transmit CCMs at the same interval. IEEE 802.1ag defines 7 possible intervals that can be used:

10ms

100ms

1s

10s

1 minute

10 minutes

A MEP detects a loss of connectivity with one of its peer MEPs when some number of CCMs have been missed. This occurs when sufficient time has passed during which a certain number of CCMs were expected, given the CCM interval. This number is called the loss threshold, and is usually set to 3.

CCM messages carry a variety of information that allows different defects to be detected in the service. This information includes:

A configured identifier for the domain of the transmitting MEP. This is referred to as the Maintenance Domain Identifier (MDID).

A configured identifier for the service of the transmitting MEP. This is referred to as the Short MA Name (SMAN). Together, the MDID and the SMAN make up the Maintenance Association Identifier (MAID). The MAID must be configured identically on every MEP in the service.

A configured numeric identifier for the MEP (the MEP ID). Each MEP in the service must be configured with a different MEP ID.

A sequence number.

A Remote Defect Indication (RDI). Each MEP includes this in the CCMs it is sending, if it has detected a defect relating to the CCMs it is receiving. This notifies all the MEPs in the service that a defect has been detected somewhere in the service.

The interval at which CCMs are being transmitted.

The status of the interface where the MEP is operating—for example, whether the interface is up, down, STP blocked, and so on.


Note The status of the interface (up/down) should not be confused with the direction of any MEPs on the interface (Up MEPs/Down MEPs).


These defects can be detected from received CCMs:

Interval mismatch—The CCM interval in the received CCM does not match the interval that the MEP is sending CCMs.

Level mismatch—A MEP has received a CCM carrying a lower maintenance level than the MEPs own level.

Loop—A CCM is received with the source MAC address equal to the MAC address of the interface where the MEP is operating.

Configuration error—A CCM is received with the same MEP ID as the MEP ID configured for the receiving MEP.

Cross-connect—A CCM is received with an MAID that does not match the locally configured MAID. This generally indicates a VLAN misconfiguration within the network, such that CCMs from one service are leaking into a different service.

Peer interface down—A CCM is received that indicates the interface on the peer is down.

Remote defect indication—A CCM is received carrying a remote defect indication.


Note This defect does not cause the MEP to include a remote defect indication in the CCMs that it is sending.


Out-of-sequence CCMs can also be detected by monitoring the sequence number in the received CCMs from each peer MEP. However, this is not considered a CCM defect.

Loopback (IEEE 802.1ag and ITU-T Y.1731)

Loopback Messages (LBM) and Loopback Replies (LBR) are used to verify connectivity between a local MEP and a particular remote MP. At the request of the administrator, a local MEP sends unicast LBMs to the remote MP. On receiving each LBM, the target maintenance point sends an LBR back to the originating MEP. Loopback indicates whether the destination is reachable or not—it does not allow hop-by-hop discovery of the path. It is similar in concept to an ICMP Echo (ping). Since loopback messages are destined for unicast addresses, they are forwarded like normal data traffic, while observing the maintenance levels. At each device that the loopback reaches, if the outgoing interface is known (in the bridge's forwarding database), then the frame is sent out on that interface. If the outgoing interface is not known, then the message is flooded on all interfaces.

Figure 7 shows an example of CFM loopback message flow between a MEP and MIP.

Figure 7 Loopback Messages

Loopback messages can be padded with user-specified data. This allows data corruption to be detected in the network. They also carry a sequence number which allows for out-of-order frames to be detected.

Except for one-way delay and jitter measurements, loopback messages can also be used for Ethernet SLA, if the peer does not support delay measurement.

Linktrace (IEEE 802.1ag and ITU-T Y.1731)

Linktrace Messages (LTM) and Linktrace Replies (LTR) are used to track the path (hop-by-hop) to a unicast destination MAC address. At the request of the operator, a local MEP sends an LTM. Each hop where there is a maintenance point sends an LTR back to the originating MEP. This allows the administrator to discover connectivity data about the path. It is similar in concept to IP traceroute, although the mechanism is different. In IP traceroute, successive probes are sent, whereas CFM Linktrace uses a single LTM which is forwarded by each MP in the path. LTMs are multicast, and carry the unicast target MAC address as data within the frame. They are intercepted at each hop where there is a maintenance point, and either retransmitted or dropped to discover the unicast path to the target MAC address.

Figure 8 shows an example of CFM linktrace message flow between MEPs and MIPs.

Figure 8 Linktrace Message Flow

The linktrace mechanism is designed to provide useful information even after a network failure. This allows it to be used to locate failures, for example after a loss of continuity is detected. To achieve this, each MP maintains a CCM Learning Database. This maps the source MAC address for each received CCM to the interface through which the CCM was received. It is similar to a typical bridge MAC learning database, except that it is based only on CCMs and it times out much more slowly—on the order of days rather than minutes.


Note In IEEE 802.1ag, the CCM Learning Database is referred to as the MIP CCM Database. However, it applies to both MIPs and MEPs.


In IEEE 802.1ag, when an MP receives an LTM message, it determines whether to send a reply using the following steps:

1. The target MAC address in the LTM is looked up in the bridge MAC learning table. If the MAC address is known, and therefore the egress interface is known, then an LTR is sent.

2. If the MAC address is not found in the bridge MAC learning table, then it is looked up in the CCM learning database. If it is found, then an LTR is sent.

3. If the MAC address is not found, then no LTR is sent (and the LTM is not forwarded).

If the target MAC has never been seen previously in the network, the linktrace operation will not produce any results.


Note IEEE 802.1ag and ITU-T Y.1731 define slightly different linktrace mechanisms. In particular, the use of the CCM learning database and the algorithm described above for responding to LTM messages are specific to IEEE 802.1ag. IEEE 802.1ag also specifies additional information that can be included in LTRs. Regardless of the differences, the two mechanisms are interoperable.


Exploratory Linktrace (Cisco)

Exploratory Linktrace is a Cisco extension to the standard linktrace mechanism described above. It has two primary purposes:

Provide a mechanism to locate faults in cases where standard linktrace does not work, such as when a MAC address has never been seen previously in the network. For example, if a new MEP has been provisioned but is not working, standard linktrace does not help isolate a problem because no frames will ever have been received from the new MEP. Exploratory Linktrace overcomes this problem.

Provide a mechanism to map the complete active network topology from a single node. This can only be done currently by examining the topology (for example, the STP blocking state) on each node in the network individually, and manually combining this information to create the overall active topology map. Exploratory linktrace allows this to be done automatically from a single node.

Exploratory Linktrace is implemented using the Vendor Specific Message (VSM) and Vendor Specific Reply (VSR) frames defined in ITU-T Y.1731. These allow vendor-specific extensions to be implemented without degrading interoperability. Exploratory Linktrace can safely be deployed in a network that includes other CFM implementations because those implementations will simply ignore the Exploratory Linktrace messages.

Exploratory Linktrace is initiated at the request of the administrator, and results in the local MEP sending a multicast Exploratory Linktrace message. Each MP in the network that receives the message sends an Exploratory Linktrace reply. MIPs that receive the message also forward it on. The initiating MEP uses all the replies to create a tree of the overall network topology.

Figure 9 show an example of the Exploratory Linktrace message flow between MEPs.

Figure 9 Exploratory Linktrace Messages and Replies

To avoid overloading the originating MEP with replies in a large network, responding MPs delay sending their replies for a random amount of time, and that time increases as the size of the network increases.

In a large network, there will be a corresponding large number of replies and the resulting topology map will be equally large. If only a part of the network is of interest, for example, because a problem has already been narrowed down to a small area, then the Exploratory Linktrace can be "directed" to start at a particular MP. Replies will thus only be received from MPs beyond that point in the network. The replies are still sent back to the originating MEP.

Alarm Indication Signal (ITU-T Y.1731)

Alarm Indication Signal (AIS) messages are used to rapidly notify MEPs when a fault is detected in the middle of a domain, in an event driven way. MEPs thereby learn of the fault much sooner than if they relied on detecting a loss of continuity, for example, failure to receive some number of consecutive CCMs.

Unlike all other CFM messages, AIS messages are injected into the middle of a domain, and sent outward toward the MEPs at the edge of the domain. Typically, AIS messages are injected by a MEP in a lower level domain. To put it another way, when a MEP sends AIS messages, they are sent in the opposite direction to other CFM messages sent by the MEP, and at a level above the MEP's own level. The AIS messages are received by the MEPs in the higher level domain, not by the peer MEPs in the same domain as the MEP sending the AIS. When a MEP receives an AIS message, it may itself send another AIS message at an even higher level.

Figure 10 show an example of AIS message flow. The maintenance domain levels are numbered at the right side of the diagram.

Figure 10 AIS Message Flow

AIS is only applicable in point-to-point networks. In multipoint networks with redundant paths, a failure at a low level does not necessarily result in a failure at a higher level, as the network may reconverge so as to route around the failed link.

AIS messages are typically sent by a MEP. However, AIS messages can also be sent when there is no MEP present, if a fault is detected in the underlying transport, such as if an interface goes down. In ITU-T Y.1731 these are referred to as server MEPs.

AIS messages are sent in response to a number of failure conditions:

Detection of CCM defects, as described "Continuity Check (IEEE 802.1ag and ITU-T Y.1731)" section.

Loss of continuity.

Receipt of AIS messages.

Failure in the underlying transport, such as when an interface is down.

Received AIS messages can be used to detect and act on failures more quickly than waiting for a loss of continuity. They can also be used to suppress any failure action, on the basis that the failure has already been detected at a lower level and will be handled there. This is described in ITU-T Y.1731; however, the former is often more useful.

Delay and Jitter Measurement (ITU-T Y.1731)

The router supports one-way and two-way delay measurement using two packet types:

Delay Measurement Message (DMM)

Delay Measurement Response (DMR)

These packets are unicast similar to loopback messages. The packets carry timestamps generated by the system time-of-day clock to support more accurate delay measurement, and also support an SLA manageability front-end.

However, unlike loopback messages, these message types can also measure one-way delay and jitter either from destination to source, or from source to destination.

For more information about SLA, see the "Ethernet SLA" section.

Synthetic Loss Measurement (ITU-T Y.1731)

Synthetic Loss Measurement (SLM) is a mechanism that injects synthetic measurement probes, and measures the loss of these probes in order to measure the loss of real data traffic. Each probe packet carries a sequence number, and the sender increments the sequence number by one for each packet that is sent and the receiver can thereby detect the lost packets by looking for missing sequence numbers.

SLM packets contain two sequence numbers; one written by the initiator into the SLM and copied by the responder into the SLR, and the other allocated by the responder and written into the SLR. These are refered to as the source-to-destination (sd) sequence number and the destination-to-source (ds) sequence number respectively.

Figure 11 shows an example of how the sequence numbers are used to calculate the Frame Loss Ratio (FLR) in each direction.

Figure 11

Synthetic Loss Measurement

Loss Measurement (ITU-T Y.1731)

Y.1731 Loss Measurement is a mechanism that measures the actual data traffic loss between a pair of MEPs in a point-to-point Ethernet service. This is in contrast to the Synthetic Loss Measurement, which measures the frame loss of synthetic frames. By using Y.1731 Loss Measurement, you can measure the one-way loss in each direction, for each priority class and also measure the loss aggregated across all priority classes.

To enable loss measurements to be made, each MEP maintains, for each priority class, both source-to-destination and destination-to-source frame counts for its peer MEPs.

There are two Loss Measurement Mechanisms (LMM); namely, single-ended and dual-ended.
Cisco IOS XR Software supports only single-ended LMM.

MEP Cross-Check

MEP cross-check supports configuration of a set of expected peer MEPs so that errors can be detected when any of the known MEPs are missing, or if any additional peer MEPs are detected that are not in the expected group.

The set of expected MEP IDs in the service is user-defined. Optionally, the corresponding MAC addresses can also be specified. CFM monitors the set of peer MEPs from which CCMs are being received. If no CCMs are ever received from one of the specified expected peer MEPs, or if a loss of continuity is detected, then a cross-check "missing" defect is detected. Similarly, if CCMs are received from a matching MEP ID but with the wrong source MAC address, a cross-check "missing" defect is detected. If CCMs are subsequently received that match the expected MEP ID, and if specified, the expected MAC address, then the defect is cleared.


Note While loss of continuity can be detected for any peer MEP, it is only treated as a defect condition if cross-check is configured.


If cross-check is configured and CCMs are received from a peer MEP with a MEP ID that is not expected, this is detected as a cross-check "unexpected" condition. However, this is not treated as a defect condition.

Configurable Logging

CFM supports logging of various conditions to syslog. Logging can be enabled independently for each service, and when the following conditions occur:

New peer MEPs are detected, or loss of continuity with a peer MEP occurs.

Changes to the CCM defect conditions are detected.

Cross-check "missing" or "unexpected" conditions are detected.

AIS condition detected (AIS messages received) or cleared (AIS messages no longer received).

EFD used to shut down an interface, or bring it back up.

EFD

Ethernet Fault Detection (EFD) is a mechanism that allows Ethernet OAM protocols, such as CFM, to control the "line protocol" state of an interface.

Unlike many other interface types, Ethernet interfaces do not have a line protocol, whose state is independent from that of the interface. For Ethernet interfaces, this role is handled by the physical-layer Ethernet protocol itself, and therefore if the interface is physically up, then it is available and traffic can flow.

EFD changes this to allow CFM to act as the line protocol for Ethernet interfaces. This allows CFM to control the interface state so that if a CFM defect (such as AIS or loss of continuity) is detected with an expected peer MEP, the interface can be shut down. This not only stops any traffic flowing, but also triggers actions in any higher-level protocols to route around the problem. For example, in the case of Layer 2 interfaces, the MAC table would be cleared and MSTP would reconverge. For Layer 3 interfaces, the ARP cache would be cleared and potentially the IGP would reconverge.


Note EFD can only be used for down MEPs. When EFD is used to shut down the interface, the CFM frames continue to flow. This allows CFM to detect when the problem has been resolved, and thus bring the interface backup automatically.


Figure 12 shows CFM detection of an error on one of its sessions EFD signaling an error to the corresponding MAC layer for the interface. This triggers the MAC to go to a down state, which further triggers all higher level protocols (Layer 2 pseudowires, IP protocols, and so on) to go down and also trigger a reconvergence where possible. As soon as CFM detects there is no longer any error, it can signal to EFD and all protocols will once again go active.

Figure 12 CFM Error Detection and EFD Trigger

Ethernet SLA

Customers require their service providers to conform to a Service Level Agreement (SLA). Consequently, service providers must be able to monitor the performance characteristics of their networks. Similarly, customers also want to monitor the performance characteristics of their networks. Cisco provides Y.1731 performance monitoring using the Cisco Ethernet SLA feature.

An SLA defines a set of criteria that guarantees a minimum level of service for customers using a service provider network. The criteria can cover many different areas, including latency, jitter, frame loss, and availability.

The Cisco Ethernet SLA feature conforms to these standards:

IEEE 802.1ag

ITU-T Y.1731

The Cisco Ethernet SLA feature provides the architecture to monitor a network at Layer 2. This architecture provides functions such as collecting, storing, displaying, and analyzing SLA statistics. These SLA statistics can be stored and displayed in various ways, so that statistical analysis can be performed.

Ethernet SLA provides the framework for performing the following major functions of performance monitoring:

Sending probes consisting of one or more packets to measure performance

Ethernet SLA provides a flexible mechanism for sending SLA probes to measure performance. Probes can consist of either CFM loopback or CFM delay measurement packets. Options are available to modify how often the packets are sent, and to specify the attributes of the probe packets such as the size and priority.

Scheduling of operations consisting of periodic probes.

A flexible mechanism is provided by Ethernet SLA to specify how often each probe should be executed, how long it should last, and when the first probe should start. Probes can be scheduled to run back-to-back to provide continuous measurements, or at a defined interval ranging from once a minute to once a week.

Collecting and storing results.

Ethernet SLA provides flexibility to specify which performance parameters should be collected and stored for each measurement probe. Performance parameters include frame delay and jitter (inter-frame delay variation). For each performance parameter, either each individual result can be stored, or the results can be aggregated by storing a counter of the number of results that fall within a particular range. A configurable amount of historical data can also be stored as well as the latest results.

Analyzing and displaying results.

Ethernet SLA performs some basic statistical analysis on the collected results, such as calculating the minimum, maximum, mean and standard deviation. It also records whether any of the probe packets were lost or misordered, or if there is any reason why the results may not be a true reflection of the performance (for example if a big jump in the local time-of-day clock was detected during the time when the measurements were being made).

Y.1731 Performance Monitoring

The ITU-T Y.1731 standard defines several mechanisms that can be used for performance monitoring in Carrier Ethernet networks. These are the measurement mechanisms that were defined in the standard:

Delay Measurement: This can be used to accurately measure frame delay by exchanging CFM frames containing timestamps, and to measure inter-frame delay variation (jitter) by comparing consecutive delay measurements. Delay Measurement messages can be used to perform these measurements:

Round-trip time

Round-trip Jitter

One-way delay (both SD and DS)

One-way jitter (both SD and DS)

SLA Probe Packet corruption count

Out of order SLA probe packet count

SLA probe packet loss

Loss Measurement: Loss Measurement is an extension to the existing Ethernet SLA feature; it adds the functionality for loss measurement defined in the Y.1731 and G.8021 ITU-T standards. This is used to accurately measure the loss of data traffic, by exchanging CFM frames containing sent and received frame counters. It is also used to measure the availability of the network by tracking periods of high loss over time. Loss Measurement messages can be used to perform these measurements:

Data packet loss

SLA probe packet loss

Out of order SLA Probe packet count

SLA Probe Packet corruption count

Synthetic Loss Measurement: The loss measurement mechanism defined in Y.1731 can only be used in point-to-point networks, and only works when there is sufficient data traffic flowing. The difficulties with the Y.1731 Loss Measurement mechanism was recognized across the industry and hence an alternative mechanism has been defined and standardized for measuring loss.

This alternative mechanism does not measure the loss of the actual data traffic, but instead injects synthetic CFM frames and measures the loss of these synthetic frames. Statistical analysis can then be used to give an approximation to the loss of data traffic. This technique is called Synthetic Loss Measurement. This has been included in the latest version of the Y.1731 standard. Synthetic Loss Measurement messages can be used to perform these measurements:

One-way loss (Source to Destination)

One-way loss (Destination to Source)

Loopback: This is not primarily targetted at performance monitoring, but can be used to approximate round-trip delay and jitter, such as when the peer device does not support delay measurement. Loopback messages can be used to perform these measurements:

Round-trip time

Round-trip jitter

SLA probe packet corruption count

Out of order SLA probe packet count

SLA probe packet loss

Loss Measurement Terminology

These are the commonly used terminology in Loss Measurement Mechanism:

Single-ended: A mechanism where device A sends a measurement packet to device B, which in turn sends a response back to device A. All calculations and results are done on device A.

Dual-ended: A mechanism where device A sends a measurement packet to device B, which does not send a response. All calculations and results are done on device B.

One-way: A measurement of the performance of packets flowing in one direction, from device A to device B, or from device B to device A.

Two-way: A measurement of the performance of packets flowing from device A to device B, and back to device A.

Forwards: A one-way measurement from the initiator (device A) to the receiver, or responder (device B).

Backwards: A one-way measurement from the responder (device B) to the initiator (device A).


Note Cisco IOS XR Software supports only single-ended LMM.


Loss Measurement Performance Attributes

These are two primary attributes that can be calculated based on loss measurements:

Frame Loss Ratio (FLR)

Availability

Frame Loss Ratio is the ratio of lost packets to sent packets:

(<num_sent > - <num_rcvd> )/(<num_sent>)

It is normally expressed as a percentage. The accuracy of the measurement depends majorly on the number of packets sent.

Availability is a complex attribute, typically measured over a long period of time, such as weeks or months. The intent of this performance attribute is to measure the proportion of time when there was prolonged high loss. Cisco IOS XR Software does not track the availability.

Limitations of Data Loss Measurement

1. Data loss measurement cannot be used in a multipoint service; it can only be used in a peer-to-peer service.

2. As a Loss Measurement Reply (LMR) contains no sequence IDs, the only field, which can be used to distinguish to which probe a given LMR corresponds, is the priority level. Also, the priority level is the only field that can determine whether the LMR is in response to an on-demand or proactive operation. This limits the number of Loss Measurement probes that can be active at a time for each local MEP to 16.

3. As loss measurements are made on a per-priority class basis, QoS policies, which alter the priority of packets processed by the network element, or re-order packets can affect the accuracy of the calculations. For the highest accuracy, packets must be counted after any QoS policies have been applied.

4. The accuracy of data loss measurement is highly dependent on the number of data packets that are sent. If the volume of data traffic is low, errors with the packet counts might be magnified. If there is no data traffic flowing, no loss measurement performance attributes can be calculated. If aggregate measurements are taken, then only 2 probes can be active at the same time: one proactive and one on-demand.

5. The accuracy of data loss measurement is highly dependent on the accuracy of platform-specific packet counters. Due to hardware limitations, it may not be possible to achieve completely accurate packet counters, especially if QoS policies are applied to the packets being counted.

6. Performing data loss measurement can have an impact on the forwarding performance of network elements; this is because of the need to count, as well as forward the packets.

7. Before starting any LMM probes,it is necessary to allocate packet counters for use with LMM on both ends (assuming both ends are running Cisco IOS XR Software).

Ethernet SLA Concepts

To successfully configure the Cisco Ethernet SLA feature, you should understand the following concepts:

Ethernet SLA Statistic

Ethernet SLA Measurement Packet

Ethernet SLA Sample

Ethernet SLA Probe

Ethernet SLA Burst

Ethernet SLA Schedule

Ethernet SLA Bucket

Ethernet SLA Aggregation Bin

Ethernet SLA Operation Profile

Ethernet SLA Operation

Ethernet SLA On-Demand Operation

Ethernet SLA Statistic

A statistic in Ethernet SLA is a single performance parameter. These statistics can be measured by Ethernet SLA:

Round-trip delay

Round-trip jitter

One-way delay from source to destination

One-way jitter from source to destination

One-way frame loss from source to destination

One-way delay from destination to source

One-way jitter from destination to source

One-way frame loss from destination to source


Note Not all statistics can be measured by all types of packet. For example, one-way statistics cannot be measured when using CFM loopback packets.


Ethernet SLA Measurement Packet

An Ethernet SLA measurement packet is a single protocol message and corresponding reply that is sent on the network for the purpose of making SLA measurements. These types of measurement packet are supported:

CFM Delay Measurement (Y.1731 DMM/DMR packets)—CFM delay measurement packets contain timestamps within the packet data that can be used for accurate measurement of frame delay and jitter. These packets can be used to measure round-trip or one-way statistics; however, the size of the DMM/DMR packets cannot be modified.


Note From Cisco IOS XR Release 4.3.x onwards, you can configure the Ethernet SLA profile to use Y.1731 DMM v1 frames. The restriction of 150 configured Ethernet SLA operations for each CFM MEP is removed not only for profiles using DMM frames, but also for profiles using the other supported Y.1731 frame types, such as loopback measurement and synthetic loss measurement. For interoperability purposes, it is still possible to configure operations to use DMM v0 frames. This is done by specifying a type of cfm-delay-measurement-v0 on the ethernet SLA profile command. The limit of 150 configured operations for each CFM MEP still applies in this case.


CFM loopback (LBM/LBR)—CFM loopback packets are less accurate, but can be used if the peer device does not support DMM/DMR packets. Only round-trip statistics can be measured because these packets do not contain timestamps. However, loopback packets can be padded, so measurements can be made using frames of a specific size.

CFM Synthetic Loss Measurement (Y.1731 SLM/SLR packets)—SLM packets contain two sequence numbers; one written by the initiator into the SLM and copied by the responder into the SLR, and the other allocated by the responder and written into the SLR. These are refered to as the source-to-destination (sd) sequence number and the destination-to-source (ds) sequence number respectively.


Note Because SLM is a statistical sampling technique, there may be some variance of the measured value around the actual loss value. Also, the accuracy of the measurement is improved by using more SLM packets for each FLR calculation.


CFM Loss Measurement (Y.1731 LMM/LMR packets)— As LMMs and LMRs contain no sequence ID, there is a limited set of data that can be used to distinguish different Loss Measurement operations, limiting the number of concurrent operations for each MEP.

Ethernet SLA Sample

A sample is a single result—a number—that relates to a given statistic. For some statistics such as round-trip delay, a sample can be measured using a single measurement packet. For other statistics such as jitter, obtaining a sample requires two measurement packets.

Ethernet SLA Probe

A probe is a sequence of measurement packets used to gather SLA samples for a specific set of statistics. The measurement packets in a probe are of a specific type (for example, CFM delay measurement or CFM loopback) and have specific attributes, such as the frame size and priority.


Note A single probe can collect data for different statistics at the same time, using the same measurement packets (for example, one-way delay and round-trip jitter).


Ethernet SLA Burst

Within a probe, measurement packets can either be sent individually, or in bursts. A burst contains two or more packets sent within a short interval apart. Each burst can last up to one minute, and bursts can follow each other immediately to provide continuous measurement within the probe.

For statistics that require two measurement packets for each sample (such as jitter), samples are only calculated based on measurement packets in the same burst. For all statistics, it is more efficient to use bursts than to send individual packets.

Ethernet SLA Schedule

An Ethernet SLA schedule describes how often probes are sent, how long each probe lasts, and at what time the first probe starts.

Ethernet SLA Bucket

For a particular statistic, a bucket is a collection of results that were gathered during a particular period of time. All of the samples for measurements that were initiated during the period of time represented by a bucket are stored in that bucket. Buckets allow results from different periods of time to be compared (for example, peak traffic to off-peak traffic).

By default, a separate bucket is created for each probe; that is, the bucket represents the period of time starting at the same time as the probe started, and continuing for the duration of the probe. The bucket will therefore contain all the results relating to measurements made by that probe.

Ethernet SLA Aggregation Bin

Rather than storing each sample separately within a bucket, an alternative is to aggregate the samples into bins. An aggregation bin is a range of sample values, and contains a counter of the number of samples that were received that fall within that range. The set of bins forms a histogram. When aggregation is enabled, each bucket contains a separate set of bins. See Figure 13.

Ethernet SLA Operation Profile

An operation profile is a configuration entity that defines the following aspects of an operation:

What packet types to send and in what quantities (probe and burst configuration)

What statistics to measure, and how to aggregate them

When to schedule the probes

An operation profile by itself does not cause any packets to be sent or statistics collected, but is used to create operation instances.

Ethernet SLA Operation

An operation is an instance of a given operation profile that is actively collecting performance data. Operation instances are created by associating an operation profile with a given source (an interface and MEP) and with a given destination (a MEP ID or MAC address). Operation instances exist for as long as the configuration is applied, and they run for an indefinite duration on an ongoing basis.

Ethernet SLA On-Demand Operation

An on-demand operation is a method of Ethernet SLA operation that can be run on an as-needed basis for a specific and finite period of time. This can be useful in situations such as when you are starting a new service or modifying the parameters for a service to verify the impact of the changes, or if you want to run a more detailed probe when a problem is detected by an ongoing scheduled operation.

On-demand operations do not use profiles and have a finite duration. The statistics that are collected are discarded after a finite time after the operation completes (two weeks), or when you manually clear them.

On-demand operations are not persistent so they are lost during certain events such as a card reload or Minimal Disruptive Restart (MDR).

Statistics Measurement and Ethernet SLA Operations Overview

Ethernet SLA statistics measurement for network performance is performed by sending packets and storing data metrics such as:

Round-trip delay time—The time for a packet to travel from source to destination and back to source again.

Round-trip jitter—The variance in round-trip delay time (latency).

One-way delay and jitter—The router also supports measurement of one-way delay or jitter from source to destination, or from destination to source.

One-way frame loss—The router also supports measurement of one-way frame loss from source to destination, or from destination to source.

In addition to these metrics, these statistics are also kept for SLA probe packets:

Packet loss count

Packet corruption event

Out-of-order event

Frame Loss Ratio (FLR)

Counters for packet loss, corruption and out-of-order packets are kept for each bucket, and in each case, a percentage of the total number of samples for that bucket is reported (for example, 4% packet corruption). For delay, jitter, and loss statistics, the minimum, maximum, mean and standard deviation for the whole bucket are reported, as well as the individual samples or aggregated bins. Also, the overall FLR for the bucket, and individual FLR measurements or aggregated bins are reported for synthetic loss measurement statistics. The packet loss count is the overall number of measurement packets lost in either direction and the one-way FLR measures the loss in each direction separately.

When aggregation is enabled using the aggregate command, bins are created to store a count of the samples that fall within a certain value range, which is set by the width keyword. Only a counter of the number of results that fall within the range for each bin is stored. This uses less memory than storing individual results. When aggregation is not used, each sample is stored separately, which can provide a more accurate statistics analysis for the operation, but it is highly memory-intensive due to the independent storage of each sample.

A bucket represents a time period during which statistics are collected. All the results received during that time period are recorded in the corresponding bucket. If aggregation is enabled, each bucket has its own set of bins and counters, and only results relating to the measurements initiated during the time period represented by the bucket are included in those counters.

By default, there is a separate bucket for each probe. The time period is determined by how long the probe lasts (configured by the probe, send (SLA), and schedule (SLA) commands).You can modify the size of buckets so that you can have more buckets per probe or fewer buckets per probe (less buckets allows the results from multiple probes to be included in the same bucket). Changing the size of the buckets for a given metric clears all stored data for that metric. All existing buckets are deleted and new buckets are created.

Scheduled SLA operation profiles run indefinitely, according to a configured schedule, and the statistics that are collected are stored in a rolling buffer, where data in the oldest bucket is discarded when a new bucket needs to be recorded.

Frame Loss Ratio (FLR) is a primary attribute that can be calculated based on loss measurements. FLR is defined by the ratio of lost packets to sent packets and expressed as a percentage value. FLR is measured in each direction (source to destination and destination to source) separately. Availability is an attribute, that is typically measured over a long period of time, such as weeks or months. The intent is to measure the proportion of time when there was prolonged high loss.

Configuration Overview of Scheduled Ethernet SLA Operations

When you configure a scheduled Ethernet SLA operation, you perform these basic steps:

1. Configure global profiles to define how packets are sent in each probe, how the probes are scheduled, and how the results are stored.

2. Configure operations from a specific local MEP to a specific peer MEP using these profiles.


Note Certain Ethernet SLA configurations use large amounts of memory which can affect the performance of other features on the system. For more information, see the "Configuring Ethernet SLA" section.


How to Configure Ethernet OAM

This section provides these configuration procedures:

Configuring Ethernet Link OAM

Configuring Ethernet CFM

Configuring Ethernet SLA

Configuring Ethernet Link OAM

Custom EOAM settings can be configured and shared on multiple interfaces by creating an EOAM profile in Ethernet configuration mode and then attaching the profile to individual interfaces. The profile configuration does not take effect until the profile is attached to an interface. After an EOAM profile is attached to an interface, individual EOAM features can be configured separately on the interface to override the profile settings when desired.

This section describes how to configure an EOAM profile and attach it to an interface in these procedures:

Configuring an Ethernet OAM Profile

Attaching an Ethernet OAM Profile to an Interface

Configuring Ethernet OAM at an Interface and Overriding the Profile Configuration

Verifying the Ethernet OAM Configuration

Configuring an Ethernet OAM Profile

Perform the following steps to configure an Ethernet OAM profile.

SUMMARY STEPS

1. configure

2. ethernet oam profile profile-name

3. link-monitor

4. symbol-period window window

5. symbol-period threshold low threshold

6. frame window window

7. frame threshold low threshold

8. frame-period window window

9. frame-period threshold low threshold

10. frame-seconds window window

11. frame-seconds threshold low threshold

12. exit

13. mib-retrieval

14. connection timeout seconds

15. mode {active | passive}

16. require-remote mode {active | passive}

17. require-remote link-monitoring

18. require-remote mib-retrieval

19. action capabilities-conflict {disable | efd | error-disable-interface}

20. action critical-event {disable | error-disable-interface}

21. action discovery-timeout {disable | efd | error-disable-interface }

22. action dying-gasp {disable | error-disable-interface}

23. action high-threshold {error-disable-interface | log}

24. action remote-loopback disable

25. action session-down {disable | efd | error-disable-interface}

26. action session-up disable

27. action uni-directional link-fault {disable | efd | error-disable-interface}

28. action wiring-conflict {disable | efd | log}

29. commit

30. end

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

configure

Example:

RP/0/RP0/CPU0:router# configure terminal

Enters global configuration mode.

Step 2 

ethernet oam profile profile-name

Example:

RP/0/RP0/CPU0:router(config)# ethernet oam profile Profile_1

Creates a new Ethernet Operations, Administration and Maintenance (OAM) profile and enters Ethernet OAM configuration mode.

Step 3 

link-monitor

Example:

RP/0/RP0/CPU0:router(config-eoam)# link-monitor

Enters the Ethernet OAM link monitor configuration mode.

Step 4 

symbol-period window window

Example:

RP/0/RP0/CPU0:router(config-eoam-lm)# symbol-period window 60000

(Optional) Configures the window size (in milliseconds) for an Ethernet OAM symbol-period error event.

The range is 1000 to 60000.

The default value is 1000.

Step 5 

symbol-period threshold low threshold high threshold

Example:

RP/0/RP0/CPU0:router(config-eoam-lm)# symbol-period threshold low 10000000 high 60000000

(Optional) Configures the thresholds (in symbols) that trigger an Ethernet OAM symbol-period error event. The high threshold is optional and is configurable only in conjunction with the low threshold.

The range is 0 to 60000000.

The default low threshold is 1.

Step 6 

frame window window

Example:

RP/0/RP0/CPU0:router(config-eoam-lm)# frame window 60

(Optional) Configures the frame window size (in milliseconds) of an OAM frame error event.

The range is from 1000 to 60000.

The default value is 1000.

Step 7 

frame threshold low threshold high threshold

Example:

RP/0/RP0/CPU0:router(config-eoam-lm)# frame threshold low 10000000 high 60000000

(Optional) Configures the thresholds (in symbols) that triggers an Ethernet OAM frame error event. The high threshold is optional and is configurable only in conjunction with the low threshold.

The range is from 0 to 60000000.

The default low threshold is 1.

Step 8 

frame-period window window

Example:

RP/0/RP0/CPU0:router(config-eoam-lm)# frame-period window 60000

(Optional) Configures the window size (in milliseconds) for an Ethernet OAM frame-period error event.

The range is from 100 to 60000.

The default value is 1000.

Step 9 

frame-period threshold low threshold high threshold

RP/0/RP0/CPU0:router(config-eoam-lm)# frame-period threshold low 100 high 1000000

(Optional) Configures the thresholds (in errors per million frames) that trigger an Ethernet OAM frame-period error event. The high threshold is optional and is configurable only in conjunction with the low threshold.

The range is from 0 to 1000000.

The default low threshold is 60000.

The IEEE 802.3 standard defines threshold crossing events as number of error frames in a window.
To comply with the standards, the low and high threshold for frame-period events is measured in errors per million frames.

Hence, the calculation to determine the remote low and high threshold is (configured threshold * frame window in received Bridge Protocol Data Unit (BPDU))/1000000. For example, if the received frame window=300, then high threshold is 20000 * 300 / 1000000 yielding the result 6.

Step 10 

frame-seconds window window

Example:

RP/0/RP0/CPU0:router(config-eoam-lm)# frame-seconds window 900000

(Optional) Configures the window size (in milliseconds) for the OAM frame-seconds error event.

The range is 10000 to 900000.

The default value is 6000.

Step 11 

frame-seconds threshold low threshold high threshold

Example:

RP/0/RP0/CPU0:router(config-eoam-lm)# frame-seconds threshold 3 threshold 900

(Optional) Configures the thresholds (in seconds) that trigger a frame-seconds error event. The high threshold value can be configured only in conjunction with the low threshold value.

The range is 1 to 900

The default value is 1.

Step 12 

exit

Example:

RP/0/RP0/CPU0:router(config-eoam-lm)# exit

Exits back to Ethernet OAM mode.

Step 13 

mib-retrieval

Example:

RP/0/RP0/CPU0:router(config-eoam)# mib-retrieval

Enables MIB retrieval in an Ethernet OAM profile or on an Ethernet OAM interface.

Step 14 

connection timeout <timeout>

Example:

RP/0/RP0/CPU0:router(config-eoam)# connection timeout 30

Configures the connection timeout period for an Ethernet OAM session. as a multiple of the hello interval.

The range is 2 to 30.

The default value is 5.

Step 15 

mode {active|passive}

Example:

RP/0/RP0/CPU0:router(config-eoam)# mode passive

Configures the Ethernet OAM mode. The default is active.

Step 16 

require-remote mode {active|passive}

Example:

RP/0/RP0/CPU0:router(config-eoam)# require-remote mode active

Requires that active mode or passive mode is configured on the remote end before the OAM session becomes active.

Step 17 

require-remote link-monitoring

Example:

RP/0/RP0/CPU0:router(config-eoam)# require-remote link-monitoring

Requires that link-monitoring is configured on the remote end before the OAM session becomes active.

Step 18 

require-remote mib-retrieval

Example:

RP/0/RP0/CPU0:router(config-eoam)# require-remote mib-retrieval

Requires that MIB-retrieval is configured on the remote end before the OAM session becomes active.

Step 19 

action capabilities-conflict {disable | efd | error-disable-interface}

Example:

RP/0/RP0/CPU0:router(config-eoam)# action capabilities-conflict efd

Specifies the action that is taken on an interface when a capabilities-conflict event occurs. The default action is to create a syslog entry.

Note If you change the default, the log keyword option is available in Interface Ethernet OAM configuration mode to override the profile setting and log the event for the interface when it occurs.

Step 20 

action critical-event {disable | error-disable-interface}

Example:

RP/0/RP0/CPU0:router(config-eoam)# action critical-event error-disable-interface

Specifies the action that is taken on an interface when a critical-event notification is received from the remote Ethernet OAM peer. The default action is to create a syslog entry.

Note If you change the default, the log keyword option is available in Interface Ethernet OAM configuration mode to override the profile setting and log the event for the interface when it occurs.

Step 21 

action discovery-timeout {disable | efd | error-disable-interface}

Example:

RP/0/RP0/CPU0:router(config-eoam)# action discovery-timeout efd

Specifies the action that is taken on an interface when a connection timeout occurs. The default action is to create a syslog entry.

Note If you change the default, the log keyword option is available in Interface Ethernet OAM configuration mode to override the profile setting and log the event for the interface when it occurs.

Step 22 

action dying-gasp {disable | error-disable-interface}

Example:

RP/0/RP0/CPU0:router(config-eoam)# action dying-gasp error-disable-interface

Specifies the action that is taken on an interface when a dying-gasp notification is received from the remote Ethernet OAM peer. The default action is to create a syslog entry.

Note If you change the default, the log keyword option is available in Interface Ethernet OAM configuration mode to override the profile setting and log the event for the interface when it occurs.

Step 23 

action high-threshold {error-disable-interface | log}

Example:

RP/0/RP0/CPU0:router(config-eoam)# action high-threshold error-disable-interface

Specifies the action that is taken on an interface when a high threshold is exceeded. The default is to take no action when a high threshold is exceeded.

Note If you change the default, the disable keyword option is available in Interface Ethernet OAM configuration mode to override the profile setting and take no action at the interface when the event occurs.

Step 24 

action remote-loopback disable

Example:

RP/0/RP0/CPU0:router(config-eoam)# action remote-loopback disable

Specifies that no action is taken on an interface when a remote-loopback event occurs. The default action is to create a syslog entry.

Note If you change the default, the log keyword option is available in Interface Ethernet OAM configuration mode to override the profile setting and log the event for the interface when it occurs.

Step 25 

action session-down {disable | efd | error-disable-interface}

Example:

RP/0/RP0/CPU0:router(config-eoam)# action session-down efd

Specifies the action that is taken on an interface when an Ethernet OAM session goes down.

Note If you change the default, the log keyword option is available in Interface Ethernet OAM configuration mode to override the profile setting and log the event for the interface when it occurs.

Step 26 

action session-up disable

Example:

RP/0/RP0/CPU0:router(config-eoam)# action session-up disable

Specifies that no action is taken on an interface when an Ethernet OAM session is established. The default action is to create a syslog entry.

Note If you change the default, the log keyword option is available in Interface Ethernet OAM configuration mode to override the profile setting and log the event for the interface when it occurs.

Step 27 

action uni-directional link-fault {disable | efd | error-disable-interface}

Specifies the action that is taken on an interface when a link-fault notification is received from the remote Ethernet OAM peer. The default action is to create a syslog entry.

Note If you change the default, the log keyword option is available in Interface Ethernet OAM configuration mode to override the profile setting and log the event for the interface when it occurs.

Note In Cisco IOS XR Release 4.x, this command replaces the action link-fault command.

Step 28 

action wiring-conflict {disable | efd | log}

Example:

RP/0/RP0/CPU0:router(config-eoam)# action session-down efd

Specifies the action that is taken on an interface when a wiring-conflict event occurs. The default is to put the interface into error-disable state.

Note If you change the default, the error-disable-interface keyword option is available in Interface Ethernet OAM configuration mode to override the profile setting and put the interface into error-disable state when the event occurs.

Step 29 

commit

Example:

RP/0/RP0/CPU0:router(config-if)# commit

Saves the configuration changes to the running configuration file and remains within the configuration session.

Step 30 

end

Example:

RP/0/RP0/CPU0:router(config-if)# end

Ends the configuration session and exits to the EXEC mode.

Attaching an Ethernet OAM Profile to an Interface

Perform the following steps to attach an Ethernet OAM profile to an interface:

SUMMARY STEPS

1. configure

2. interface [GigabitEthernet | TenGigE] interface-path-id

3. ethernet oam

4. profile profile-name

5. commit

6. end

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

configure

Example:

RP/0/RP0/CPU0:router# configure terminal

Enters global configuration mode.

Step 2 

interface [GigabitEthernet | TenGigE] inter- face-path-id

Example:

RP/0/RP0/CPU0:router(config)# interface
TenGigE 0/1/0/0

Enters interface configuration mode and specifies the Ethernet interface name and notation rack/slot/module/port.

Note The example indicates an 8-port 10-Gigabit Ethernet interface in modular services card slot 1.

Step 3 

ethernet oam

Example:

RP/0/RP0/CPU0:router(config-if)# ethernet oam

Enables Ethernet OAM and enters interface Ethernet OAM configuration mode.

Step 4 

profile profile-name

Example:

RP/0/RP0/CPU0:router(config-if-eoam)# profile Profile_1

Attaches the specified Ethernet OAM profile (profile-name), and all of its configuration, to the interface.

Step 5 

commit

Example:

RP/0/RP0/CPU0:router(config-if)# commit

Saves the configuration changes to the running configuration file and remains within the configuration session.

Step 6 

end

Example:

RP/0/RP0/CPU0:router(config-if)# end

Ends the configuration session and exits to the EXEC mode.

Configuring Ethernet OAM at an Interface and Overriding the Profile Configuration

Using an EOAM profile is an efficient way of configuring multiple interfaces with a common EOAM configuration. However, if you want to use a profile but also change the behavior of certain functions for a particular interface, then you can override the profile configuration. To override certain profile settings that are applied to an interface, you can configure that command in interface Ethernet OAM configuration mode to change the behavior for that interface.

In some cases, only certain keyword options are available in interface Ethernet OAM configuration due to the default settings for the command. For example, without any configuration of the action commands, several forms of the command have a default behavior of creating a syslog entry when a profile is created and applied to an interface. Therefore, the log keyword is not available in Ethernet OAM configuration for these commands in the profile because it is the default behavior. However, the log keyword is available in Interface Ethernet OAM configuration if the default is changed in the profile configuration so you can retain the action of creating a syslog entry for a particular interface.

To see all of the default Ethernet OAM configuration settings, see the "Verifying the Ethernet OAM Configuration" section.

To configure Ethernet OAM settings at an interface and override the profile configuration, perform the following steps:

SUMMARY STEPS

1. configure

2. interface [GigabitEthernet | TenGigE] interface-path-id

3. ethernet oam

4. interface-Ethernet-OAM-command

5. commit

6. end

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

configure

Example:

RP/0/RP0/CPU0:router# configure terminal

Enters global configuration mode.

Step 2 

interface [GigabitEthernet | TenGigE] inter- face-path-id

Example:

RP/0/RP0/CPU0:router(config)# interface
TenGigE 0/1/0/0

Enters interface configuration mode and specifies the Ethernet interface name and notation rack/slot/module/port.

Note The example indicates an 8-port 10-Gigabit Ethernet interface in modular services card slot 1.

Step 3 

ethernet oam

Example:

RP/0/RP0/CPU0:router(config-if)# ethernet oam

Enables Ethernet OAM and enters interface Ethernet OAM configuration mode.

Step 4 

interface-Ethernet-OAM-command

Example:

RP/0/RP0/CPU0:router(config-if-eoam)# action capabilities-conflict error-disable-interface

Configures a setting for an Ethernet OAM configuration command and overrides the setting for the profile configuration, where interface-Ethernet-OAM-command is one of the supported commands on the platform in interface Ethernet OAM configuration mode.

Step 5 

commit

Example:

RP/0/RP0/CPU0:router(config-if)# commit

Saves the configuration changes to the running configuration file and remains within the configuration session.

Step 6 

end

Example:

RP/0/RP0/CPU0:router(config-if)# end

Ends the configuration session and exits to the EXEC mode.

Verifying the Ethernet OAM Configuration

Use the show ethernet oam configuration command to display the values for the Ethernet OAM configuration for a particular interface, or for all interfaces. The following example shows the default values for Ethernet OAM settings:


Note Some of these settings are not supported on certain platforms, but the defaults are still reported. On the Cisco CRS-1 Router, the following areas are unsupported:

Hello interval configuration

Remote loopback

Uni-directional link-fault detection


RP/0/RP0/CPU0:router# show ethernet oam configuration
Thu Aug  5 22:07:06.870 DST
GigabitEthernet0/4/0/0:
  Hello interval:                                              1s
  Link monitoring enabled:                                      Y
  Remote loopback enabled:                                      N
  Mib retrieval enabled:                                        N
  Uni-directional link-fault detection enabled:                 N
  Configured mode:                                         Active
  Connection timeout:                                           5
  Symbol period window:                                         0
  Symbol period low threshold:                                  1
  Symbol period high threshold:                              None
  Frame window:                                              1000
  Frame low threshold:                                          1
  Frame high threshold:                                      None
  Frame period window:                                       1000
  Frame period low threshold:                                   1
  Frame period high threshold:                               None
  Frame seconds window:                                     60000
  Frame seconds low threshold:                                  1
  Frame seconds high threshold:                              None
  High threshold action:                                     None
  Link fault action:                                          Log
  Dying gasp action:                                          Log
  Critical event action:                                      Log
  Discovery timeout action:                                   Log
  Capabilities conflict action:                               Log
  Wiring conflict action:                           Error-Disable
  Session up action:                                          Log
  Session down action:                                        Log
  Remote loopback action:                                     Log
  Require remote mode:                                     Ignore
  Require remote MIB retrieval:                                 N
  Require remote loopback support:                              N
  Require remote link monitoring:                               N

Configuring Ethernet CFM

To configure Ethernet CFM, perform the following tasks:

Configuring a CFM Maintenance Domain (required)

Configuring Services for a CFM Maintenance Domain (required)

Enabling and Configuring Continuity Check for a CFM Service (optional)

Configuring Automatic MIP Creation for a CFM Service (optional)

Configuring Cross-Check on a MEP for a CFM Service (optional)

Configuring Other Options for a CFM Service (optional)

Configuring CFM MEPs (required)

Configuring Y.1731 AIS (optional)

Configuring EFD for a CFM Service (optional)

Verifying the CFM Configuration

Troubleshooting Tips

Configuring a CFM Maintenance Domain

To configure a CFM maintenance domain, perform the following steps:

SUMMARY STEPS

1. configure

2. ethernet cfm

3. domain domain-name level level-value [id [null] [dns DNS-name] [mac H.H.H] [string string] ]

4. traceroute cache hold-time minutes size entries

5. end
or
commit

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

configure

Example:

RP/0/RP0/CPU0:router# configure

Enters global configuration mode.

Step 2 

ethernet cfm

Example:

RP/0/RP0/CPU0:router(config)# ethernet cfm

Enters Ethernet Connectivity Fault Management (CFM) configuration mode.

Step 3 

domain domain-name level level-value [id [null] [dns DNS-name] [mac H.H.H] [string string] ]

Example:
RP/0/RP0/CPU0:router(config-cfm)# domain 
Domain_One level 1 id string D1 

Creates and names a container for all domain configurations and enters CFM domain configuration mode.

The level must be specified.

The id is the maintenance domain identifier (MDID) and is used as the first part of the maintenance association identifier (MAID) in CFM frames. If the MDID is not specified, the domain name is used as the MDID by default.

Step 4 

traceroute cache hold-time minutes size entries

Example:
RP/0/RP0/CPU0:router(config-cfm)# traceroute 
cache hold-time 1 size 3000 

(Optional) Sets the maximum limit of traceroute cache entries or the maximum time limit to hold the traceroute cache entries. The default is 100 minutes and 100 entries.

Step 5 

end

or

commit

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn)# commit

Saves configuration changes.

When you use the end command, the system prompts you to commit changes:

Uncommitted changes found, commit them before 
exiting(yes/no/cancel)? 
[cancel]:
 
        

Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Configuring Services for a CFM Maintenance Domain

You can configure up to 32000 CFM services for a maintenance domain.

To configure services for a CFM maintenance domain, perform the following steps:

SUMMARY STEPS

1. configure

2. ethernet cfm

3. domain domain-name level level-value [id [null] [dns DNS-name] [mac H.H.H] [string string]]

4. service service-name {down-meps | xconnect group xconnect-group-name p2p xconnect-name}[id [string text] | [number number] | [vlan-id id-number] | [vpn-id oui-vpnid]]

5. end
or
commit

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

configure

Example:

RP/0/RP0/CPU0:router# configure

Enters global configuration mode.

Step 2 

ethernet cfm

Example:

RP/0/RP0/CPU0:router(config)# ethernet cfm

Enters Ethernet CFM configuration mode.

Step 3 

domain domain-name level level-value [id [null] [dns DNS-name] [mac H.H.H] [string string] ]

Example:
RP/0/RP0/CPU0:router(config-cfm)# domain 
Domain_One level 1 id string D1 

Creates and names a container for all domain configurations at a specified maintenance level, and enters CFM domain configuration mode.

The id is the maintenance domain identifier (MDID) and is used as the first part of the maintenance association identifier (MAID) in CFM frames. If the MDID is not specified, the domain name is used as the MDID by default.

Step 4 

service service-name {down-meps | xconnect group xconnect-group-name p2p xconnect-name}[id [string text] | [number number] | [vlan-id id-number] | [vpn-id oui-vpnid]]

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn)# service Bridge_Service bridge group BD1 bridge-domain B1

Configures and associates a service with the domain and enters CFM domain service configuration mode. You can specify that the service is used only for down MEPs, or associate the service with an xconnect where MIPs and up MEPs will be created.

The id sets the short MA name.

Step 5 

end

or

commit

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# commit

Saves configuration changes.

When you use the end command, the system prompts you to commit changes:

Uncommitted changes found, commit them before 
exiting(yes/no/cancel)? 
[cancel]:
 
        

Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Enabling and Configuring Continuity Check for a CFM Service

The Cisco CRS-1 Router supports Continuity Check as defined in the IEEE 802.1ag specification, and supports CCMs intervals of 100 ms and longer. The overall packet rates for CCM messages are up to 2000 CCMs-per-second sent, and up to 2000 CCMs-per-second received, per card.


Note If Ethernet SLA is configured, the overall combined packet rate for CCMs and SLA frames is 4000 frames-per-second in each direction, per card.


To configure Continuity Check for a CFM service, complete the following steps:

SUMMARY STEPS

1. configure

2. ethernet cfm

3. domain domain-name level level-value [id [null] [dns DNS-name] [mac H.H.H] [string string]]

4. service service-name {down-meps | xconnect group xconnect-group-name p2p xconnect-name}[id [string text] | [number number] | [vlan-id id-number] | [vpn-id oui-vpnid]]

5. continuity-check interval time [loss-threshold threshold ]

6. continuity-check archive hold-time minutes

7. continuity-check loss auto-traceroute

8. end
or
commit

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

configure

Example:

RP/0/RP0/CPU0:router# configure

Enters global configuration mode.

Step 2 

ethernet cfm

Example:

RP/0/RP0/CPU0:router(config)# ethernet cfm

Enters Ethernet Connectivity Fault Management (CFM) configuration mode.

Step 3 

domain domain-name level level-value [id [null] [dns DNS-name] [mac H.H.H] [string string] ]

Example:
RP/0/RP0/CPU0:router(config-cfm)# domain 
Domain_One level 1 id string D1 

Creates and names a container for all domain configurations and enters the CFM domain configuration mode.

The level must be specified.

The id is the maintenance domain identifier (MDID) and is used as the first part of the maintenance association identifier (MAID) in CFM frames. If the MDID is not specified, the domain name is used as the MDID by default.

Step 4 

service service-name {down-meps | xconnect group xconnect-group-name p2p xconnect-name}[id [string text] | [number number] | [vlan-id id-number] | [vpn-id oui-vpnid]]

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn)# service Bridge_Service bridge group BD1 bridge-domain B1

Configures and associates a service with the domain and enters CFM domain service configuration mode. You can specify that the service is used only for down MEPs, or associate the service with an xconnect where MIPs and up MEPs will be created.

The id sets the short MA name.

Step 5 

continuity-check interval time [loss-threshold threshold]

Example:
RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# 
continuity-check interval 100m loss-threshold 
10 

(Optional) Enables Continuity Check and specifies the time interval at which CCMs are transmitted or to set the threshold limit for when a MEP is declared down.

Step 6 

continuity-check archive hold-time minutes

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# continuity-check archive hold-time 100

(Optional) Configures how long information about peer MEPs is stored after they have timed out.

Step 7 

continuity-check loss auto-traceroute

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# continuity-check loss auto-traceroute

(Optional) Configures automatic triggering of a traceroute when a MEP is declared down.

Step 8 

end

or

commit

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# commit

Saves configuration changes.

When you use the end command, the system prompts you to commit changes:

Uncommitted changes found, commit them before 
exiting(yes/no/cancel)? 
[cancel]:
 
        

Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Configuring Automatic MIP Creation for a CFM Service

For more information about the algorithm for creating MIPs, see the "MIP Creation" section.

To configure automatic MIP creation for a CFM service, complete the following steps:

SUMMARY STEPS

1. configure

2. ethernet cfm

3. domain domain-name level level-value [id [null] [dns DNS-name] [mac H.H.H] [string string]]

4. service service-name {down-meps | xconnect group xconnect-group-name p2p xconnect-name}[id [string text] | [number number] | [vlan-id id-number] | [vpn-id oui-vpnid]]

5. mip auto-create {all | lower-mep-only}

6. end
or
commit

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

configure

Example:

RP/0/RP0/CPU0:router# configure

Enters global configuration mode.

Step 2 

ethernet cfm

Example:

RP/0/RP0/CPU0:router# ethernet cfm

Enters the Ethernet Connectivity Fault Management (CFM) configuration mode.

Step 3 

domain domain-name level level-value [id [null] [dns DNS-name] [mac H.H.H] [string string] ]

Example:
RP/0/RP0/CPU0:router(config-cfm)# domain 
Domain_One level 1 id string D1 

Creates and names a container for all domain configurations and enters the CFM domain configuration mode.

The level must be specified.

The id is the maintenance domain identifier (MDID) and is used as the first part of the maintenance association identifier (MAID) in CFM frames. If the MDID is not specified, the domain name is used as the MDID by default.

Step 4 

service service-name {down-meps | xconnect group xconnect-group-name p2p xconnect-name}[id [string text] | [number number] | [vlan-id id-number] | [vpn-id oui-vpnid]]

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn)# service Bridge_Service bridge group BD1 bridge-domain B1

Configures and associates a service with the domain and enters CFM domain service configuration mode. You can specify that the service is used only for down MEPs, or associate the service with an xconnect where MIPs and up MEPs will be created.

The id sets the short MA name.

Step 5 

mip auto-create {all | lower-mep-only}

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# mip auto-create all

(Optional) Enables the automatic creation of MIPs in an xconnect.

Step 6 

end

or

commit

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# commit

Saves configuration changes.

When you use the end command, the system prompts you to commit changes:

Uncommitted changes found, commit them before 
exiting(yes/no/cancel)? 
[cancel]:
 
        

Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Configuring Cross-Check on a MEP for a CFM Service

To configure cross-check on a MEP for a CFM service and specify the expected set of MEPs, complete the following steps:

SUMMARY STEPS

1. configure

2. ethernet cfm

3. domain domain-name level level-value [id [null] [dns DNS-name] [mac H.H.H] [string string]]

4. service service-name {down-meps | xconnect group xconnect-group-name p2p xconnect-name}[id [string text] | [number number] | [vlan-id id-number] | [vpn-id oui-vpnid]]

5. mep crosscheck

6. mep-id mep-id-number [mac-address mac-address]

7. end
or
commit

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

configure

Example:

RP/0/RP0/CPU0:router# configure

Enters global configuration mode.

Step 2 

ethernet cfm

Example:

RP/0/RP0/CPU0:router# ethernet cfm

Enters the Ethernet Connectivity Fault Management (CFM) configuration mode.

Step 3 

domain domain-name level level-value [id [null] [dns DNS-name] [mac H.H.H] [string string] ]

Example:
RP/0/RP0/CPU0:router(config-cfm)# domain 
Domain_One level 1 id string D1 

Creates and names a container for all domain configurations and enters the CFM domain configuration mode.

The level must be specified.

The id is the maintenance domain identifier (MDID) and is used as the first part of the maintenance association identifier (MAID) in CFM frames. If the MDID is not specified, the domain name is used as the MDID by default.

Step 4 

service service-name {down-meps | xconnect group xconnect-group-name p2p xconnect-name}[id [string text] | [number number] | [vlan-id id-number] | [vpn-id oui-vpnid]]

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn)# service Bridge_Service bridge group BD1 bridge-domain B1

Configures and associates a service with the domain and enters CFM domain service configuration mode. You can specify that the service is used only for down MEPs, or associate the service with an xconnect where MIPs and up MEPs will be created.

The id sets the short MA name.

Step 5 

mep crosscheck

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# mep crosscheck mep-id 10

Enters CFM MEP crosscheck configuration mode.

Step 6 

mep-id mep-id-number [mac-address mac-address]

Example:

RP/0/RP0/CPU0:router(config-cfm-xcheck)# mep-id 10

Enables cross-check on a MEP.

Note Repeat this command for every MEP that you want included in the expected set of MEPs for cross-check.

Step 7 

end

or

commit

Example:

RP/0/RP0/CPU0:router(config-cfm-xcheck)# commit

Saves configuration changes.

When you use the end command, the system prompts you to commit changes:

Uncommitted changes found, commit them before 
exiting(yes/no/cancel)? 
[cancel]:
 
        

Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Configuring Other Options for a CFM Service

To configure other options for a CFM service, complete the following steps:

SUMMARY STEPS

1. configure

2. ethernet cfm

3. domain domain-name level level-value [id [null] [dns DNS-name] [mac H.H.H] [string string]]

4. service service-name {down-meps | xconnect group xconnect-group-name p2p xconnect-name}[id [string text] | [number number] | [vlan-id id-number] | [vpn-id oui-vpnid]]

5. maximum meps number

6. log {ais | continuity-check errors | continuity-check mep changes | crosscheck errors | efd}

7. end
or
commit

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

configure

Example:

RP/0/RP0/CPU0:router# configure

Enters global configuration mode.

Step 2 

ethernet cfm

Example:

RP/0/RP0/CPU0:router# ethernet cfm

Enters the Ethernet Connectivity Fault Management (CFM) configuration mode.

Step 3 

domain domain-name level level-value [id [null] [dns DNS-name] [mac H.H.H] [string string] ]

Example:
RP/0/RP0/CPU0:router(config-cfm)# domain 
Domain_One level 1 id string D1 

Creates and names a container for all domain configurations and enters the CFM domain configuration mode.

The level must be specified.

The id is the maintenance domain identifier (MDID) and is used as the first part of the maintenance association identifier (MAID) in CFM frames. If the MDID is not specified, the domain name is used as the MDID by default.

Step 4 

service service-name {down-meps | xconnect group xconnect-group-name p2p xconnect-name}[id [string text] | [number number] | [vlan-id id-number] | [vpn-id oui-vpnid]]

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn)# service Bridge_Service bridge group BD1 bridge-domain B1

Configures and associates a service with the domain and enters CFM domain service configuration mode. You can specify that the service is used only for down MEPs, or associate the service with an xconnect where MIPs and up MEPs will be created.

The id sets the short MA name.

Step 5 

maximum-meps number

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# maximum-meps 1000

(Optional) Configures the maximum number (2 to 8190) of MEPs across the network, which limits the number of peer MEPs recorded in the database.

Step 6 

log {ais|continuity-check errors|continuity-check mep changes|crosscheck errors|efd}

Example:
RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# log 
continuity-check errors 

(Optional) Enables logging of certain types of events.

Step 7 

end

or

commit

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# commit

Saves configuration changes.

When you use the end command, the system prompts you to commit changes:

Uncommitted changes found, commit them before 
exiting(yes/no/cancel)? 
[cancel]:
 
        

Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Configuring CFM MEPs

When you configure CFM MEPs, consider these guidelines:

Up to 32000 local MEPs are supported per card.

CFM maintenance points can be created only on physical Ethernet interfaces.

A new configuration under the MEP submode called loss-measurement counters is used to allocate the packet counters used for LMM.

SUMMARY STEPS

1. configure

2. interface {GigabitEthernet | TenGigE} interface-path-id

3. ethernet cfm

4. mep domain domain-name service service-name mep-id id-number

5. cos cos

6. end
or
commit

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

configure

Example:

RP/0/RP0/CPU0:router# configure

Enters global configuration mode.

Step 2 

interface {GigabitEthernet | TenGigE} 
interface-path-id
Example:
RP/0/RP0/CPU0:router(config)# interface 
gigabitethernet 0/1/0/1

Type of Ethernet interface on which you want to create a MEP. Enter GigabitEthernet or TenGigE and the physical interface or virtual interface.

Note Use the show interfaces command to see a list of all interfaces currently configured on the router.

For more information about the syntax for the router, use the question mark (?) online help function.

Step 3 

ethernet cfm

Example:

RP/0/RP0/CPU0:router(config-if)# ethernet cfm

Enters interface Ethernet CFM configuration mode.

Step 4 

mep domain domain-name service service-name mep-id id-number

Example:

RP/0/RP0/CPU0:router(config-if-cfm)# mep domain Dm1 service Sv1 mep-id 1

Creates a maintenance end point (MEP) on an interface and enters interface CFM MEP configuration mode.

Step 5 

cos cos

Example:

RP/0/RP0/CPU0:router(config-if-cfm-mep)# cos 7

(Optional) Configures the class of service (CoS) (from 0 to 7) for all CFM packets generated by the MEP on an interface. If not configured, the CoS is inherited from the Ethernet interface.

Step 6 

end

or

commit

Example:

RP/0/RP0/CPU0:router(config-if-cfm-mep)# commit

Saves configuration changes.

When you use the end command, the system prompts you to commit changes:

Uncommitted changes found, commit them before 
exiting(yes/no/cancel)? 
[cancel]:
 
        

Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Configuring Y.1731 AIS

This section has the following step procedures:

Configuring AIS in a CFM Domain Service

Configuring AIS on a CFM Interface

Configuring AIS in a CFM Domain Service

Use the following procedure to configure Alarm Indication Signal (AIS) transmission for a CFM domain service and configure AIS logging.

SUMMARY STEPS

1. configure

2. ethernet cfm

3. domain name level level

4. service name xconnect group xconnect-group-name p2p xconnect-name

5. ais transmission [interval {1s | 1m}][cos cos]

6. log ais

7. end
or
commit

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

configure

Example:

RP/0/RP0/CPU0:router# configure

Enters global configuration mode.

Step 2 

ethernet cfm

Example:

RP/0/RP0/CPU0:router(config)# ethernet cfm

Enters Ethernet CFM global configuration mode.

Step 3 

domain name level level

Example:

RP/0/RP0/CPU0:router(config-cfm)# domain D1 level 1

Specifies the domain and domain level.

Step 4 

service name xconnect group xconnect-group-name p2p xconnect-name

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn)# service S1 bridge group BG1 bridge-domain BD2

Specifies the service and cross-connect group and name.

Step 5 

ais transmission [interval {1s|1m}][cos cos]

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# ais transmission interval 1m cos 7

Configures Alarm Indication Signal (AIS) transmission for a Connectivity Fault Management (CFM) domain service.

Step 6 

log ais

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# log ais

Configures AIS logging for a Connectivity Fault Management (CFM) domain service to indicate when AIS or LCK packets are received.

Step 7 

end

or

commit

Example:

RP/0/RP0/CPU0:router(config-sla-prof-stat-cfg)# commit

Saves configuration changes.

When you issue the end command, the system prompts you to commit changes:

Uncommitted changes found, commit them before 
exiting(yes/no/cancel)? 
[cancel]:
 
        

Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Configuring AIS on a CFM Interface

To configure AIS on a CFM interface, perform the following steps:

SUMMARY STEPS

1. configure

2. interface gigabitethernet interface-path-id

3. ethernet cfm

4. ais transmission up interval 1m cos cos

5. end
or
commit

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

configure

Example:

RP/0/RP0/CPU0:router# configure

Enters global configuration mode.

Step 2 

interface gigabitethernet interface-path-id

Example:

RP/0/RP0/CPU0:router# interface gigabitethernet 0/1/0/2

Enters interface configuration mode.

Step 3 

ethernet cfm

Example:

RP/0/RP0/CPU0:router(config)# ethernet cfm

Enters Ethernet CFM interface configuration mode.

Step 4 

ais transmission up interval 1m cos cos

Example:

RP/0/RP0/CPU0:router(config-if-cfm)# ais transmission up interval 1m cos 7

Configures Alarm Indication Signal (AIS) transmission on a Connectivity Fault Management (CFM) interface.

Step 5 

end

or

commit

Example:

RP/0/RP0/CPU0:router(config-sla-prof-stat-cfg)# commit

Saves configuration changes.

When you issue the end command, the system prompts you to commit changes:

Uncommitted changes found, commit them before 
exiting(yes/no/cancel)? 
[cancel]:
 
        

Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Configuring EFD for a CFM Service

To configure EFD for a CFM service, complete the following steps.

Restrictions

EFD is not supported on up MEPs. It can only be configured on down MEPs, within a particular service.

SUMMARY STEPS

1. configure

2. ethernet cfm

3. domain domain-name level level-value

4. service service-name down-meps

5. efd

6. log efd

7. end
or
commit

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

configure

Example:

RP/0/RP0/CPU0:router# configure

Enters global configuration mode.

Step 2 

ethernet cfm

Example:

RP/0/RP0/CPU0:router(config)# ethernet cfm

Enters CFM configuration mode.

Step 3 

domain domain-name level level-value

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn)# domain D1 level 1

Specifies or creates the CFM domain and enters CFM domain configuration mode.

Step 4 

service service-name down-meps

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn)# service S1 down-meps

Specifies or creates the CFM service for down MEPS and enters CFM domain service configuration mode.

Step 5 

efd

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# efd

Enables EFD on all down MEPs in the down MEPS service.

Step 6 

log efd

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# log efd

(Optional) Enables logging of EFD state changes on an interface.

Step 7 

end

or

commit

Example:

RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# commit

Saves configuration changes.

When you issue the end command, the system prompts you to commit changes:

Uncommitted changes found, commit them before 
exiting(yes/no/cancel)? 
[cancel]:
 
        

Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Verifying the EFD Configuration

The following example shows how to display all interfaces that are shut down because of Ethernet Fault Detection (EFD):

RP/0/RP0/CPU0:router# show efd interfaces 
 
   
Server VLAN MA
==============
Interface         Clients
-------------------------
GigE0/0/0/0.0     CFM

Verifying the CFM Configuration

To verify the CFM configuration, use one or more of the following commands:

Command
Purpose

show ethernet cfm configuration-errors [domain domain-name] [interface interface-path-id ]

Displays information about errors that are preventing configured CFM operations from becoming active, as well as any warnings that have occurred.

show ethernet cfm local maintenance-points domain name [service name] | interface type interface-path-id] [mep | mip]

Displays a list of local maintenance points.


Troubleshooting Tips

To troubleshoot problems within the CFM network, perform the following steps:


Step 1 To verify connectivity to a problematic MEP, use the ping ethernet cfm command as shown in the following example:

RP/0/RP0/CPU0:router# ping ethernet cfm domain D1 service S1 mep-id 16 source 
interface GigabitEthernet 0/0/0/0 
 
   
Type escape sequence to abort.
Sending 5 CFM Loopbacks, timeout is 2 seconds -
Domain foo (level 2), Service foo
Source: MEP ID 1, interface GigabitEthernet0/0/0/0
Target: 0001.0002.0003 (MEP ID 16):
  Running (5s) ...
Success rate is 60.0 percent (3/5), round-trip min/avg/max = 1251/1349/1402 ms
Out-of-sequence: 0.0 percent (0/3)
Bad data: 0.0 percent (0/3)
Received packet rate: 1.4 pps
 
   

Step 2 If the results of the ping ethernet cfm command show a problem with connectivity to the peer MEP, use the traceroute ethernet cfm command to help further isolate the location of the problem as shown in the following example:

RP/0/RP0/CPU0:router# traceroute ethernet cfm domain D1 service S1 mep-id 16 source 
interface gigabitethernet 0/0/0/0 
 
   
Traceroutes in domain D1 (level 4), service S1
Source: MEP-ID 1, interface GigabitEthernet0/0/0/0
================================================================================
Traceroute at 2009-05-18 12:09:10 to 0001.0203.0402,
TTL 64, Trans ID 2:
 
   
Hop Hostname/Last            Ingress MAC/name       Egress MAC/Name        Relay
--- ------------------------ ---------------------- ---------------------- -----
  1 ios                      0001.0203.0400 [Down]                         FDB  
      0000-0001.0203.0400    Gi0/0/0/0                                          
  2 abc                                             0001.0203.0401 [Ok]    FDB  
      ios                                           Not present                 
  3 bcd                      0001.0203.0402 [Ok]                           Hit  
      abc                    GigE0/0                                            
Replies dropped: 0

If the target was a MEP, verify that the last hop shows "Hit" in the Relay field to confirm connectivity to the peer MEP.

If the Relay field contains "MPDB" for any of the hops, then the target MAC address was not found in the bridge MAC learning table at that hop, and the result is relying on CCM learning. This result can occur under normal conditions, but it can also indicate a problem. If you used the ping ethernet cfm command before using the traceroute ethernet cfm command, then the MAC address should have been learned. If "MPDB" is appearing in that case, then this indicates a problem at that point in the network.

Configuring Ethernet SLA

This section describes how to configure Ethernet SLA.

Ethernet SLA Configuration Guidelines


Caution Certain SLA configurations can use a large amount of memory which can affect the performance of other features on the router.

Before you configure Ethernet SLA, consider the following guidelines:

Aggregation—Use of the aggregate none command significantly increases the amount of memory required because each individual measurement is recorded, rather than just counts for each aggregation bin. When you configure aggregation, consider that more bins will require more memory.

Buckets archive—When you configure the buckets archive command, consider that the more history that is kept, the more memory will be used.

Measuring two statistics (such as both delay and jitter) will use approximately twice as much memory as measuring one.

Separate statistics are stored for one-way source-to-destination and destination-to-source measurements, which consumes twice as much memory as storing a single set of round-trip statistics.

The Cisco CRS-1 Router supports SLA packet of 100 ms and longer. The overall packet rates for SLA is up to 2000 CCMs-per-second sent, and up to 2000 CCMs-per-second received, per card.

The following procedure provides the steps to configure Ethernet Service Level Agreement (SLA) monitoring at Layer 2.

To configure SLA, perform the following tasks:

Configuring an SLA Operation Profile

Configuring SLA Probe Parameters in a Profile

Configuring SLA Statistics Measurement in a Profile

Configuring a Schedule for an SLA Operation Probe in a Profile

Configuring an SLA Operation

Configuring an On-Demand SLA Operation

Configuring an On-Demand Ethernet SLA Operation for CFM Synthetic Loss Measurement

Configuring an SLA Operation Profile

To configure a profile, perform the following steps:

SUMMARY STEPS

1. configure

2. ethernet sla

3. profile profile-name type {cfm-delay-measurement | cfm-loopback | cfm-synthetic-loss-measurement | cfm-loss-measurement}

4. end
or
commit

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

configure

Example:

RP/0/RP0/CPU0:router# configure

Enters global configuration mode.

Step 2 

ethernet sla

Example:

RP/0/RP0/CPU0:router# ethernet sla

Enters the SLA configuration mode.

Step 3 

profile profile-name type {cfm-delay-measurement | cfm-loopback | cfm-synthetic-loss-measurement|

cfm-loss-measurement}

Example:
RP/0/RP0/CPU0:router(config-sla)# profile  
Prof1 type cfm-loopback 

Creates an SLA operation profile and enters the SLA profile configuration mode.

Step 4 

end

or

commit

Example:

RP/0/RP0/CPU0:router(config-sla)# commit

Saves configuration changes.

When you issue the end command, the system prompts you to commit changes:

Uncommitted changes found, commit them before 
exiting(yes/no/cancel)? 
[cancel]:
 
        

Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Configuring SLA Probe Parameters in a Profile

To configure SLA probe parameters in a profile, perform these steps beginning in SLA profile configuration mode:

SUMMARY STEPS

1. probe

2. send burst {every number {seconds | minutes | hours}| once} packet count packets interval number {seconds | milliseconds}
or
send packet {every number {milliseconds | seconds | minutes | hours} | once}

3. packet size bytes [test pattern {hex 0xHHHHHHHH | pseudo-random}]

4. priority priority

5. synthetic loss calculation packets number

6. end
or
commit

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

probe

Example:
RP/0/RP0/CPU0:router(config-sla-prof)# probe 

Enters the SLA profile probe configuration mode.

Step 2 

send burst {every number {seconds | minutes | hours} | once} packet count packets interval number {seconds | milliseconds}

or

send packet {every number {milliseconds | seconds | minutes | hours} | once}

Example:

RP/0/RP0/CPU0:router(config-sla-prof-pb)# send burst every 60 seconds packet count 100 interval 100 milliseconds

or

RP/0/RP0/CPU0:router(config-sla-prof-pb)# send burst once packet count 2 interval 1 second

or

RP/0/RP0/CPU0:router(config-sla-prof-pb)# send 
packet every 100 milliseconds 

Configures the number and timing of packets sent by a probe in an operations profile.

Step 3 

packet size bytes [test pattern {hex 0xHHHHHHHH | pseudo-random}]

Example:

RP/0/RP0/CPU0:router(config-sla-prof-pb)# packet size 9000

Configures the minimum size (in bytes) for outgoing probe packets, including padding when necessary. Use the test pattern keyword to specify a hexadecimal string to use as the padding characters, or a pseudo-random bit sequence. The default padding is 0's. The packet size can be configured for SLM, loopback, and DMM/R probes.

Step 4 

priority priority

Example:

RP/0/RP0/CPU0:router(config-sla-prof-pb)# priority 7

Configures the priority of outgoing SLA probe packets.

If the operation is running on an interface, which matches tagged traffic, then a priority value must be configured for the probe. This priority value must match the "on-the-wire" CoS value of the packets to be counted (after any tag rewrites). LMM packets are sent with this priority value as the CoS-value, and LMR packets must be received with the same CoS-value; otherwise, all LMRs are dropped. Note that this is the case even when aggregate counters are being collected.

If the operation is running on an interface which matches untagged traffic, then configuring a priority value is not permitted. In this case, only aggregate counters can be collected. When configuring data-loss measurement operations, configuration must also be applied to allocate the correct packet counters (matching the CoS values to be collected) on the interface, using the "loss-measurement counters" configuration under the MEP properties submode.

Step 5 

synthetic loss calculation packets number

Example:

RP/0/RP0/CPU0:router(config-sla-prof-pb)# synthetic loss calculation packets 25

Configures the number of packets that must be used to make each FLR calculation in the case of synthetic loss measurements. This item can only be configured for packet types that support synthetic loss measurement.

An FLR value is calculated for each discrete block of packets. For instance, if a value of 10 is configured, the first FLR value would be calculated based on packets 0 - 9 and the second FLR value based on packets 10 - 19, and so on.

Step 6 

end

or

commit

Example:

RP/0/RP0/CPU0:router(config-sla-prof-pb)# commit

Saves configuration changes.

When you issue the end command, the system prompts you to commit changes:

Uncommitted changes found, commit them before 
exiting(yes/no/cancel)? 
[cancel]:
 
        

Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Configuring SLA Statistics Measurement in a Profile

The Ethernet SLA feature supports measurement of one-way and two-way delay and jitter statistics, and one-way FLR statistics.

Prerequisites

To configure one-way delay or jitter measurements, you must first configure the profile (SLA) command using the type cfm-delay-measurement form of the command.

Restrictions

One-way delay and jitter measurements are not supported by cfm-loopback profile types.

To configure SLA statistics measurement in a profile, perform these steps beginning in SLA profile configuration mode:

SUMMARY STEPS

1. statistics measure {one-way-delay-ds | one-way-delay-sd | one-way-jitter-ds | one-way-jitter-sd | round-trip-delay | round-trip-jitter | one-way-loss-ds | one-way-loss-sd}

2. aggregate {bins count width width | none}

3. buckets size number {per-probe | probes}

4. buckets archive number

5. end
or
commit

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

statistics measure {one-way-delay-ds | one-way-delay-sd | one-way-jitter-ds | one-way-jitter-sd | round-trip-delay | round-trip-jitter | one-way-loss-ds | one-way-loss-sd}

Example:

RP/0/RP0/CPU0:router(config-sla-prof)# statistics measure round-trip-delay

Enables the collection of SLA statistics, and enters SLA profile statistics configuration mode.

Step 2 

aggregate {bins count width width | none}

Example:

RP/0/RP0/CPU0:router(config-sla-prof-stat-cfg)# aggregate bins 100 width 10000

Configures the size and number of bins into which to aggregate the results of statistics collection.

For delay measurements, a width between 1-10000, in milliseconds, must be specified if the number of bins is at least 2.

For jitter measurements, a width between 1-10000, in milliseconds, must be specified if the number of bins is at least 3.

For loss measurements, a width between 1-100, in percentage points, must be specified if the number of bins is at least 2.

Step 3 

buckets size number {per-probe | probes}

Example:

RP/0/RP0/CPU0:router(config-sla-prof-stat-cfg)# buckets size 100 per-probe

Configures the size of the buckets in which statistics are collected.

Step 4 

buckets archive number

Example:

RP/0/RP0/CPU0:router(config-sla-prof-stat-cfg)# buckets archive 50

Configures the number of buckets to store in memory.

Step 5 

end

or

commit

Example:

RP/0/RP0/CPU0:router(config-sla-prof-stat-cfg)# commit

Saves configuration changes.

When you issue the end command, the system prompts you to commit changes:

Uncommitted changes found, commit them before 
exiting(yes/no/cancel)? 
[cancel]:
 
        

Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Configuring a Schedule for an SLA Operation Probe in a Profile

This section describes how to configure a schedule for an SLA operation probe on an ongoing basis within an SLA profile. For information about how to configure a schedule for a limited, on-demand SLA operation, see the "Configuring an On-Demand SLA Operation" section.

To configure a schedule for an SLA operation probe, perform the following steps beginning in SLA profile configuration mode:

SUMMARY STEPS

1. schedule every week on day [at hh:mm] [for duration {seconds | minutes | hours | days | week}]
or
schedule every day [at hh:mm] [for duration {seconds | minutes | hours | days | week}]
or
schedule every number {hours | minutes}[first at hh:mm[.ss]] [for duration {seconds | minutes | hours | days | week}]

2. end
or
commit

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

schedule every week on day [at hh:mm] [for duration {seconds | minutes | hours | days | week}]
or
schedule every day [at hh:mm] [for duration {seconds | minutes | hours | days | week}]
or
schedule every number {hours | minutes}[first at hh:mm[.ss]] [for duration {seconds | minutes | hours | days | week}]

Example:

RP/0/RP0/CPU0:router(config-sla-prof)# schedule every week on Monday at 23:30 for 1 hour

or

RP/0/RP0/CPU0:router(config-sla-prof)# schedule every day at 11:30 for 5 minutes

or

RP/0/RP0/CPU0:router(config-sla-prof)# schedule every 2 hours first at 13:45:01

or

RP/0/RP0/CPU0:router(config-sla-prof)# schedule 
every 6 hours for 2 hours 

Schedules an operation probe in a profile. A profile may contain only one schedule.

Step 2 

end

or

commit

Example:

RP/0/RP0/CPU0:router(config-sla-prof-stat-cfg)# commit

Saves configuration changes.

When you issue the end command, the system prompts you to commit changes:

Uncommitted changes found, commit them before 
exiting(yes/no/cancel)? 
[cancel]:
 
        

Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Configuring an SLA Operation

This section describes how to configure an ongoing SLA operation on a MEP using an SLA profile.

SUMMARY STEPS

1. interface [GigabitEthernet | TenGigE] interface-path-id

2. ethernet cfm

3. mep domain domain-name service service-name mep-id id-number

4. sla operation profile profile-name target {mep-id id | mac-address mac-address}

5.

6. end
or
commit

DETAILED STEPS

 
Command or Action
Purpose

Step 1 

interface [GigabitEthernet | TenGigE] 
interface-path-id 
Example:

RP/0/RP0/CPU0:router(config-if)# interface gigabitethernet 0/1/0/1

Physical interface or virtual interface.

Note Use the show interfaces command to see a list of all interfaces currently configured on the router.

For more information about the syntax for the router, use the question mark (?) online help function.

Step 2 

ethernet cfm

Example:

RP/0/RP0/CPU0:router(config-if)# ethernet cfm

Enters interface CFM configuration mode.

Step 3 

mep domain domain-name service service-name mep-id id-number

Example:

RP/0/RP0/CPU0:router(config-if-cfm)# mep domain Dm1 service Sv1 mep-id 1

Creates a MEP on an interface and enters interface CFM MEP configuration mode.

Step 4 

sla operation profile profile-name target {mep-id id | mac-address mac-address}

Example:

RP/0/RP0/CPU0:router(config-if-cfm-mep)# sla operation profile Profile_1 target mac-address 01:23:45:67:89:ab

Creates an operation instance from a MEP to a specified destination.

Step 5 

end

or

commit

Example:

RP/0/RP0/CPU0:router(config-sla-prof-stat-cfg)# commit

Saves configuration changes.

When you issue the end command, the system prompts you to commit changes:

Uncommitted changes found, commit them before 
exiting(yes/no/cancel)? 
[cancel]:
 
        

Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Configuring an On-Demand SLA Operation

The Cisco CRS-1 Router supports configuration of on-demand SLA operations to run on an as-needed basis for a finite period of time.

This section includes the following topics:

Configuration Guidelines

Configuring an On-Demand Ethernet SLA Operation for CFM Delay Measurement

Configuring an On-Demand Ethernet SLA Operation for CFM Loopback

Configuring an On-Demand Ethernet SLA Operation for CFM Synthetic Loss Measurement

Configuration Guidelines

When you configure on-demand SLA operations, consider the following guidelines:

Each MEP supports up to 50 on-demand operations.

Each card supports up to 250 on-demand operations.

On-demand Ethernet SLA operations can be run in addition to any other ongoing scheduled SLA operations that you might have configured, and use similar amounts of CPU and router memory. When configuring an on-demand Ethernet SLA operation, you should consider your existing SLA operation configuration and the potential impact of additional packet processing to your normal operations.

If you do not specify a schedule for the on-demand operation, the probe defaults to running one time beginning two seconds from the execution of the command, and runs for a ten-second duration.

If you do not specify the statistics for the probe to measure, it defaults to measuring all statistics, inlcuding these statistics by probe type:

CFM loopback—Two-way delay and jitter is measured by default.

CFM delay measurement—One-way delay and jitter in both directions, in addition to two-way delay and jitter is measured by default.

CFM synthetic loss measurement—One-way FLR in both directions is measured by default.

The default operation mode is synchronous, where progress of the operation is reported to the console and the output of the statistics collection is displayed.

Configuring an On-Demand Ethernet SLA Operation for CFM Delay Measurement

To configure an on-demand Ethernet SLA operation for CFM delay measurement, use the following command in privileged EXEC configuration mode:

Command
Purpose

ethernet sla on-demand operation type cfm-delay-measurement probe [priority number]
[send {packet {once | every number {milliseconds | seconds | minutes | hours}} | burst {once | every number {seconds | minutes | hours}} packet count number interval number {milliseconds | seconds}]
domain domain-name source interface type interface-path-id target {mac-address H.H.H.H | mep-id id-number}
[statistics measure {one-way-delay-ds | one-way-delay-sd | one-way-jitter-ds | one-way-jitter-sd | round-trip-delay | round-trip-jitter}][aggregate {none | bins number width milliseconds}] [buckets {archive number | size number {per-probe | probes}}]
[schedule {now | at hh:mm[.ss] [day [month [year]]] | in number {seconds | minutes | hours}}[for duration {seconds | minutes | hours}][repeat every number {seconds | minutes | hours} count probes]]
[asynchronous]

Example:

RP/0/RP0/CPU0:router# ethernet sla on-demand operation type cfm-delay-measurement probe domain D1 source interface TenGigE 0/6/1/0 target mep-id 100

Configures an on-demand Ethernet SLA operation for CFM delay measurement.

The example shows a minimum configuration, that specifies the local domain and source interface and target MEP, using the following defaults:

Send a burst once for a packet count of 10 and interval of 1 second (10-second probe).

Use default class of service (CoS) for the egress interface.

Measure all statistics, including both one-way and round-trip delay and jitter statistics.

Aggregate statistics into one bin.

Schedule now.

Display results on the console.


Configuring an On-Demand Ethernet SLA Operation for CFM Loopback

To configure an on-demand Ethernet SLA operation for CFM loopback, use the following command in privileged EXEC configuration mode:

Command
Purpose

ethernet sla on-demand operation type cfm-loopback probe
[packet size bytes [test pattern {hex 0xHHHHHHHH | pseudo-random}]]
[priority number]
[send {packet {once | every number {milliseconds | seconds | minutes | hours}} | burst {once | every number {seconds | minutes | hours}} packet count number interval number {milliseconds | seconds}]
domain domain-name source interface type interface-path-id target {mac-address H.H.H.H | mep-id id-number}
[statistics measure {round-trip-delay | round-trip-jitter}][aggregate {none | bins number width milliseconds}][buckets {archive number | size number {per-probe | probes}}]
[schedule {now | at hh:mm[.ss] [day [month [year]]] | in number {seconds | minutes | hours}}[for duration {seconds | minutes | hours}][repeat every number {seconds | minutes | hours} count probes]]
[asynchronous]

Example:

RP/0/RP0/CPU0:router# ethernet sla on-demand operation type cfm-loopback probe packet size 1500 domain D1 source interface TenGigE 0/6/1/0 target mep-id 100

Configures an on-demand Ethernet SLA operation for CFM loopback.

The example shows a minimum configuration, but specifies the option of a minimum packet size, and specifies the local domain and source interface and target MEP, using the following defaults:

Send a burst once for a packet count of 10 and interval of 1 second (10-second probe).

Use default test pattern of 0's for padding.

Use default class of service (CoS) for the egress interface.

Measure all statistics.

Aggregate statistics into one bin.

Schedule now.

Display results on the console.


Configuring an On-Demand Ethernet SLA Operation for CFM Synthetic Loss Measurement

To configure an on-demand Ethernet SLA operation for CFM synthetic loss measurement, use this command in privileged EXEC configuration mode:

Command
Purpose

ethernet sla on-demand operation type cfm-synthetic-loss-measurement probe [priority number]
[send {packet {once | every number {milliseconds | seconds | minutes | hours}} | burst {once | every number {seconds | minutes | hours}} packet count number interval number {milliseconds | seconds}]
domain domain-name source interface type interface-path-id target {mac-address H.H.H.H | mep-id id-number}
[synthetic loss calculation packets number]
[statistics measure { one-way-loss-ds | one-way-loss-sd}][aggregate {none | bins number width milliseconds}] [buckets {archive number | size number {per-probe | probes}}]
[schedule {now | at hh:mm[.ss] [day [month [year]]] | in number {seconds | minutes | hours}}[for duration {seconds | minutes | hours}][repeat every number {seconds | minutes | hours} count probes]]
[asynchronous]

Example:

RP/0/RP0/CPU0:router# ethernet sla on-demand operation type cfm-synthetic-loss-measurement probe domain D1 source interface TenGigE 0/6/1/0 target mac-address 2.3.4

Configures an on-demand Ethernet SLA operation for CFM synthetic loss measurement.

The example shows a minimum configuration, that specifies the local domain and source interface and target MEP.


Verifying SLA Configuration

To verify SLA configuration, use one or more of these commands:

Command
Purpose

show ethernet sla configuration-errors [domain domain-name] [interface interface-path-id] [profile profile-name]

Displays information about errors that are preventing configured SLA operations from becoming active, as well as any warnings that have occurred.

show ethernet sla operations [detail] [domain domain-name] [interface interface-path-id] [profile profile-name]

Displays information about configured SLA operations.


Configuration Examples for Ethernet OAM

This section provides the following configuration examples:

Configuration Examples for EOAM Interfaces

Configuration Examples for Ethernet CFM

Configuration Examples for Ethernet SLA

Configuration Examples for EOAM Interfaces

This section provides the following configuration examples:

Configuring an Ethernet OAM Profile Globally: Example

Configuring Ethernet OAM Features on an Individual Interface: Example

Configuring Ethernet OAM Features to Override the Profile on an Individual Interface: Example

Clearing Ethernet OAM Statistics on an Interface: Example

Enabling SNMP Server Traps on a Router: Example

Configuring an Ethernet OAM Profile Globally: Example

The following example shows how to configure an Ethernet OAM profile globally:

configure terminal
 ethernet oam profile Profile_1
  link-monitor
   symbol-period window 60000
   symbol-period threshold low 10000000 high 60000000
   frame window 60
   frame threshold low 10000000 high 60000000 
   frame-period window 60000
   frame-period threshold low 100 high 12000000 
   frame-seconds window 900000
   frame-seconds threshold 3 threshold 900 
   exit
  mib-retrieval
  connection timeout 30
  require-remote mode active 
  require-remote link-monitoring 
  require-remote mib-retrieval
  action dying-gasp error-disable-interface 
  action critical-event error-disable-interface
  action discovery-timeout error-disable-interface
  action session-down error-disable-interface
  action capabilities-conflict error-disable-interface
  action wiring-conflict error-disable-interface
  action remote-loopback error-disable-interface
  commit

Configuring Ethernet OAM Features on an Individual Interface: Example

The following example shows how to configure Ethernet OAM features on an individual interface:

configure terminal
 interface TenGigE 0/1/0/0
  ethernet oam 
   link-monitor
    symbol-period window 60000
    symbol-period threshold low 10000000 high 60000000
    frame window 60
    frame threshold low 10000000 high 60000000 
    frame-period window 60000
    frame-period threshold low 100 high 12000000 
    frame-seconds window 900000
    frame-seconds threshold 3 threshold 900 
    exit
   mib-retrieval
   connection timeout 30
   require-remote mode active 
   require-remote link-monitoring 
   require-remote mib-retrieval
   action link-fault  error-disable-interface
   action dying-gasp error-disable-interface 
   action critical-event error-disable-interface
   action discovery-timeout error-disable-interface
   action session-down error-disable-interface
   action capabilities-conflict error-disable-interface
   action wiring-conflict error-disable-interface
   action remote-loopback error-disable-interface
   commit

Configuring Ethernet OAM Features to Override the Profile on an Individual Interface: Example

The following example shows the configuration of Ethernet OAM features in a profile followed by an override of that configuration on an interface:

configure terminal
 ethernet oam profile Profile_1
  mode passive 
  action dying-gasp disable 
  action critical-event disable
  action discovery-timeout disable
  action session-up disable 
  action session-down disable 
  action capabilities-conflict disable
  action wiring-conflict disable 
  action remote-loopback disable
  action uni-directional link-fault error-disable-interface
  commit
 
   
configure terminal
 interface TenGigE 0/1/0/0
  ethernet oam 
   profile Profile_1
    mode active 
    action dying-gasp log 
    action critical-event log 
    action discovery-timeout log 
    action session-up log
    action session-down log
    action capabilities-conflict log
    action wiring-conflict log
    action remote-loopback log
    action uni-directional link-fault log
    uni-directional link-fault detection
    commit

Clearing Ethernet OAM Statistics on an Interface: Example

The following example shows how to clear Ethernet OAM statistics on an interface:

RP/0/RP0/CPU0:router# clear ethernet oam statistics interface gigabitethernet 0/1/5/1 

Enabling SNMP Server Traps on a Router: Example

The following example shows how to enable SNMP server traps on a router:

configure terminal
  ethernet oam profile Profile_1 
  snmp-server traps ethernet oam events 

Configuration Examples for Ethernet CFM

This section includes the following examples:

Ethernet CFM Domain Configuration: Example

Ethernet CFM Service Configuration: Example

Continuity Check for an Ethernet CFM Service Configuration: Example

MIP Creation for an Ethernet CFM Service Configuration: Example

Cross-check for an Ethernet CFM Service Configuration: Example

Other Ethernet CFM Service Parameter Configuration: Example

MEP Configuration: Example

Ethernet CFM Show Command: Examples

AIS for CFM Configuration: Examples

AIS for CFM Show Commands: Examples

EFD Configuration: Examples

Displaying EFD Information: Examples

Ethernet CFM Domain Configuration: Example

This example shows how to configure a basic domain for Ethernet CFM:

configure 
 ethernet cfm 
  traceroute cache hold-time 1 size 3000 
  domain Domain_One level 1 id string D1 
  commit

Ethernet CFM Service Configuration: Example

The following example shows how to create a service for an Ethernet CFM domain:

  service Cross_Connect_1 xconnect group XG1 p2p X1 
  commit

Continuity Check for an Ethernet CFM Service Configuration: Example

The following example shows how to configure continuity-check options for an Ethernet CFM service:

   continuity-check archive hold-time 100 
   continuity-check loss auto-traceroute
   continuity-check interval 100ms loss-threshold 10 
   commit

MIP Creation for an Ethernet CFM Service Configuration: Example

The following example shows how to enable MIP auto-creation for an Ethernet CFM service:

   mip auto-create all 
   commit

Cross-check for an Ethernet CFM Service Configuration: Example

The following example shows how to configure cross-check for MEPs in an Ethernet CFM service:

   mep crosscheck 
    mep-id 10 
    mep-id 20 
    commit

Other Ethernet CFM Service Parameter Configuration: Example

The following example shows how to configure other Ethernet CFM service options:

    maximum-meps 4000 
    log continuity-check errors 
    commit
    exit
   exit
  exit

MEP Configuration: Example

The following example shows how to configure a MEP for Ethernet CFM on an interface:

 interface gigabitethernet 0/1/0/1
  ethernet cfm 
  mep domain Dm1 service Sv1 mep-id 1 
  commit

Ethernet CFM Show Command: Examples

The following examples show how to verify the configuration of Ethernet Connectivity Fault Management (CFM):

Example 1

The following example shows how to display all the maintenance points that have been created on an interface:

RP/0/RP0/CPU0:router# show ethernet cfm local maintenance-points 
 
   
Domain/Level         Service             Interface         Type   ID   MAC
-------------------- ------------------- ----------------- ------ ---- --------
fig/5                bay                 Gi0/10/0/12.23456 Dn MEP    2 44:55:66
fig/5                bay                 Gi0/0/1/0.1       MIP         55:66:77
fred/3               barney              Gi0/1/0/0.1       Up MEP    5 66:77:88!

Example 2

The following example shows how to display all the CFM configuration errors on all domains:

RP/0/RP0/CPU0:router# show ethernet cfm configuration-errors 
 
   
Domain fig (level 5), Service bay
 * An Up MEP is configured for this domain on interface GigabitEthernet0/1/2/3.234 and an 
Up MEP is also configured for domain blort, which is at the same level (5).
 * A MEP is configured on interface GigabitEthernet0/3/2/1.1 for this domain/service, 
which has CC interval 100ms, but the lowest interval supported on that interface is 1s

Example 3

The following example shows how to display operational state for local maintenance end points (MEPs):

RP/0/RP0/CPU0:router# show ethernet cfm local meps 
 
   
 A - AIS received                I - Wrong interval
 R - Remote Defect received      V - Wrong Level
 L - Loop (our MAC received)     T - Timed out (archived)
 C - Config (our ID received)    M - Missing (cross-check)
 X - Cross-connect (wrong MAID)  U - Unexpected (cross-check)
 P - Peer port down
 
   
Domain foo (level 6), Service bar
   ID Interface (State)        Dir MEPs/Err RD Defects AIS
----- ------------------------ --- -------- -- ------- ---
  100 Gi1/1/0/1.234 (Up)       Up     0/0   N  A       L7
                                                          
Domain fred (level 5), Service barney            
   ID Interface (State)        Dir MEPs/Err RD Defects AIS
----- ------------------------ --- -------- -- ------- ---
    2 Gi0/1/0/0.234 (Up)       Up     3/2   Y  RPC     L6

Example 4

The following example shows how to display operational state of other maintenance end points (MEPs) detected by a local MEP:

RP/0/RP0/CPU0:router# show ethernet cfm peer meps 
 
   
Flags:
 > - Ok                           I - Wrong interval
 R - Remote Defect received       V - Wrong level
 L - Loop (our MAC received)      T - Timed out
 C - Config (our ID received)     M - Missing (cross-check)
 X - Cross-connect (wrong MAID)   U - Unexpected (cross-check)
 
   
Domain fred (level 7), Service barney
Up MEP on GigabitEthernet0/1/0/0.234, MEP-ID 2
================================================================================
St    ID MAC address    Port    Up/Downtime   CcmRcvd SeqErr   RDI Error
-- ----- -------------- ------- ----------- --------- ------ ----- -----
 >     1 0011.2233.4455 Up      00:00:01         1234      0     0     0
R>     4 4455.6677.8899 Up      1d 03:04         3456      0   234     0
L      2 1122.3344.5566 Up      3w 1d 6h         3254      0     0  3254
C      2 7788.9900.1122 Test    00:13            2345      6    20  2345
X      3 2233.4455.6677 Up      00:23              30      0     0    30
I      3 3344.5566.7788 Down    00:34           12345      0   300  1234
V      3 8899.0011.2233 Blocked 00:35              45      0     0    45
 T     5 5566.7788.9900         00:56              20      0     0     0
M      6                                            0      0     0     0
U>     7 6677.8899.0011 Up      00:02             456      0     0     0
 
   
Domain fred (level 7), Service fig 
Down MEP on GigabitEthernet0/10/0/12.123, MEP-ID 3
================================================================================
St    ID MAC address    Port    Up/Downtime  CcmRcvd SeqErr   RDI Error
-- ----- -------------- ------- ----------- -------- ------ ----- -----
 >     1 9900.1122.3344 Up      03:45           4321      0     0     0

Example 5

The following example shows how to display operational state of other maintenance end points (MEPs) detected by a local MEP with details:

RP/0/RP0/CPU0:router# show ethernet cfm peer meps detail
Domain dom3 (level 5), Service ser3
Down MEP on GigabitEthernet0/0/0/0 MEP-ID 1
================================================================================
Peer MEP-ID 10, MAC 0001.0203.0403
   CFM state: Wrong level, for 00:01:34
   Port state: Up
   CCM defects detected:    V - Wrong Level
   CCMs received: 5
     Out-of-sequence:             0
     Remote Defect received:      5
     Wrong Level:                 0
     Cross-connect (wrong MAID):  0
     Wrong Interval:              5
     Loop (our MAC received):     0
     Config (our ID received):    0
Last CCM received 00:00:06 ago:
     Level: 4, Version: 0, Interval: 1min
     Sequence number: 5, MEP-ID: 10
     MAID: String: dom3, String: ser3
     Port status: Up, Interface status: Up
 
   
 
   
Domain dom4 (level 2), Service ser4
Down MEP on GigabitEthernet0/0/0/0 MEP-ID 1
================================================================================
Peer MEP-ID 20, MAC 0001.0203.0402
   CFM state: Ok, for 00:00:04
   Port state: Up
   CCMs received: 7
     Out-of-sequence:             1
     Remote Defect received:      0
     Wrong Level:                 0
     Cross-connect (wrong MAID):  0
     Wrong Interval:              0
     Loop (our MAC received):     0
	 Config (our ID received):    0
Last CCM received 00:00:04 ago:
     Level: 2, Version: 0, Interval: 10s
     Sequence number: 1, MEP-ID: 20
     MAID: String: dom4, String: ser4
     Chassis ID: Local: ios; Management address: 'Not specified'
     Port status: Up, Interface status: Up
 
   
Peer MEP-ID 21, MAC 0001.0203.0403
   CFM state: Ok, for 00:00:05
   Port state: Up
   CCMs received: 6
     Out-of-sequence:             0
     Remote Defect received:      0
     Wrong Level:                 0
     Cross-connect (wrong MAID):  0
     Wrong Interval:              0
     Loop (our MAC received):     0
     Config (our ID received):    0
Last CCM received 00:00:05 ago:
     Level: 2, Version: 0, Interval: 10s
     Sequence number: 1, MEP-ID: 21
     MAID: String: dom4, String: ser4
     Port status: Up, Interface status: Up
 
   
 
   
Domain dom5 (level 2), Service ser5
Up MEP on Standby Bundle-Ether 1 MEP-ID 1
================================================================================
Peer MEP-ID 600, MAC 0001.0203.0401
   CFM state: Ok (Standby), for 00:00:08, RDI received
   Port state: Down
   CCM defects detected:    Defects below ignored on local standby MEP
                            I - Wrong Interval
                            R - Remote Defect received
   CCMs received: 5
     Out-of-sequence:             0
     Remote Defect received: 	  5
	 Wrong Level:                 0
     Cross-connect W(wrong MAID): 0
     Wrong Interval:              5
     Loop (our MAC received):     0
     Config (our ID received):    0
   Last CCM received 00:00:08 ago:
     Level: 2, Version: 0, Interval: 10s
     Sequence number: 1, MEP-ID: 600
     MAID: DNS-like: dom5, String: ser5
     Chassis ID: Local: ios; Management address: 'Not specified'
     Port status: Up, Interface status: Down
 
   
Peer MEP-ID 601, MAC 0001.0203.0402
   CFM state: Timed Out (Standby), for 00:15:14, RDI received
   Port state: Down
   CCM defects detected:    Defects below ignored on local standby MEP
                            I - Wrong Interval
                            R - Remote Defect received
                            T - Timed Out
                            P - Peer port down
   CCMs received: 2
     Out-of-sequence:             0
     Remote Defect received:      2
     Wrong Level:                 0
     Cross-connect (wrong MAID):  0
     Wrong Interval:              2
     Loop (our MAC received):     0
     Config (our ID received):    0
   Last CCM received 00:15:49 ago:
     Level: 2, Version: 0, Interval: 10s
     Sequence number: 1, MEP-ID: 600
     MAID: DNS-like: dom5, String: ser5
     Chassis ID: Local: ios; Management address: 'Not specified'
     Port status: Up, Interface status: Down

AIS for CFM Configuration: Examples

Example 1

The following example shows how to configure Alarm Indication Signal (AIS) transmission for a CFM domain service:

RP/0/RP0/CPU0:router# configure 
RP/0/RP0/CPU0:router(config)# ethernet cfm
RP/0/RP0/CPU0:router(config-cfm)# domain D1 level 1 
RP/0/RP0/CPU0:router(config-cfm-dmn)# service Cross_Connect_1 xconnect group XG1 p2p 
RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# ais transmission interval 1m cos 7 

Example 2

The following example shows how to configure AIS logging for a Connectivity Fault Management (CFM) domain service to indicate when AIS or LCK packets are received:

RP/0/RP0/CPU0:router# configure 
RP/0/RP0/CPU0:router(config)# ethernet cfm
RP/0/RP0/CPU0:router(config-cfm)# domain D1 level 1 
RP/0/RP0/CPU0:router(config-cfm-dmn)# service Cross_Connect_1 xconnect group XG1 p2p 
RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# log ais
 
   

The following example shows how to configure AIS transmission on a CFM interface.

RP/0/RP0/CPU0:router# configure 
RP/0/RP0/CPU0:router(config)# interface gigabitethernet 0/1/0/2 
RP/0/RP0/CPU0:router(config-if)# ethernet cfm 
RP/0/0RP0RSP0/CPU0:router(config-if-cfm)# ais transmission up interval 1m cos 7 

AIS for CFM Show Commands: Examples

This section includes the following examples:

show ethernet cfm interfaces ais Command: Example

show ethernet cfm local meps Command: Examples

show ethernet cfm interfaces ais Command: Example

The following example shows how to display the information published in the Interface AIS table:

RP/0/RP0/CPU0:router# show ethernet cfm interfaces ais 
 
   
Defects (from at least one peer MEP):
 A - AIS received                I - Wrong interval
 R - Remote Defect received      V - Wrong Level
 L - Loop (our MAC received)     T - Timed out (archived)
 C - Config (our ID received)    M - Missing (cross-check)
 X - Cross-connect (wrong MAID)  U - Unexpected (cross-check)
 P - Peer port down              D - Local port down
 
   
                               Trigger                   Transmission
                         AIS  ---------    Via    ---------------------------
Interface (State)        Dir  L Defects  Levels   L Int Last started  Packets
------------------------ ---  - -------  -------  - --- ------------ --------
Gi0/1/0/0.234 (Up)       Dn   5 RPC      6        7 1s  01:32:56 ago     5576
Gi0/1/0/0.567 (Up)       Up   0 M        2,3      5 1s  00:16:23 ago      983
Gi0/1/0/1.1 (Dn)         Up     D                 7 60s 01:02:44 ago     3764
Gi0/1/0/2 (Up)           Dn   0 RX       1!

show ethernet cfm local meps Command: Examples

Example 1: Default

The following example shows how to display statistics for local maintenance end points (MEPs):

RP/0/RP0/CPU0:router# show ethernet cfm local meps 
 
   
 A - AIS received                I - Wrong interval
 R - Remote Defect received      V - Wrong Level
 L - Loop (our MAC received)     T - Timed out (archived)
 C - Config (our ID received)    M - Missing (cross-check)
 X - Cross-connect (wrong MAID)  U - Unexpected (cross-check)
 P - Peer port down
 
   
Domain foo (level 6), Service bar
   ID Interface (State)        Dir MEPs/Err RD Defects AIS
----- ------------------------ --- -------- -- ------- ---
  100 Gi1/1/0/1.234 (Up)       Up     0/0   N  A       7
                                                          
Domain fred (level 5), Service barney            
   ID Interface (State)        Dir MEPs/Err RD Defects AIS
----- ------------------------ --- -------- -- ------- ---
    2 Gi0/1/0/0.234 (Up)       Up     3/2   Y  RPC     6

Example 2: Domain Service

The following example shows how to display statistics for MEPs in a domain service:

RP/0/RSP0RP0/CPU0:router# show ethernet cfm local meps domain foo service bar detail
 
   
Domain foo (level 6), Service bar
Up MEP on GigabitEthernet0/1/0/0.234, MEP-ID 100
================================================================================
  Interface state: Up      MAC address: 1122.3344.5566
  Peer MEPs: 0 up, 0 with errors, 0 timed out (archived)
 
   
  CCM generation enabled:  No
  AIS generation enabled:  Yes (level: 7, interval: 1s)
  Sending AIS:             Yes (started 01:32:56 ago)
  Receiving AIS:           Yes (from lower MEP, started 01:32:56 ago)
 
   
Domain fred (level 5), Service barney 
Up MEP on GigabitEthernet0/1/0/0.234, MEP-ID 2
================================================================================
  Interface state: Up      MAC address: 1122.3344.5566
  Peer MEPs: 3 up, 2 with errors, 0 timed out (archived)
  Cross-check defects: 0 missing, 0 unexpected
 
   
  CCM generation enabled:  Yes (Remote Defect detected: Yes)
  CCM defects detected:    R - Remote Defect received
                           P - Peer port down
                           C - Config (our ID received)
  AIS generation enabled:  Yes (level: 6, interval: 1s)
  Sending AIS:             Yes (to higher MEP, started 01:32:56 ago)
  Receiving AIS:           No

Example 3: Verbose

The following example shows how to display verbose statistics for MEPs in a domain service:


Note The Discarded CCMs field is not displayed when the number is zero (0). It is unusual for the count of discarded CCMs to be any thing other than zero, since CCMs are only discarded when the limit on the number of peer MEPs is reached.


 
   
RP/0/RSP0RP0/CPU0:router# show ethernet cfm local meps domain foo service bar verbose 
 
   
Domain foo (level 6), Service bar
Up MEP on GigabitEthernet0/1/0/0.234, MEP-ID 100
================================================================================
  Interface state: Up      MAC address: 1122.3344.5566
  Peer MEPs: 0 up, 0 with errors, 0 timed out (archived)
 
   
  CCM generation enabled:  No
  AIS generation enabled:  Yes (level: 7, interval: 1s)
  Sending AIS:             Yes (started 01:32:56 ago)
  Receiving AIS:           Yes (from lower MEP, started 01:32:56 ago)
  
  Packet        Sent      Received
  ------  ----------  -----------------------------------------------------
  CCM              0             0  (out of seq: 0)
  LBM              0             0
  LBR              0             0  (out of seq: 0, with bad data: 0)
  AIS           5576             0
  LCK              -             0
 
   
Domain fred (level 5), Service barney 
Up MEP on GigabitEthernet0/1/0/0.234, MEP-ID 2
================================================================================
  Interface state: Up      MAC address: 1122.3344.5566
  Peer MEPs: 3 up, 2 with errors, 0 timed out (archived)
  Cross-check defects: 0 missing, 0 unexpected
 
   
  CCM generation enabled:  Yes (Remote Defect detected: Yes)
  CCM defects detected:    R - Remote Defect received
                           P - Peer port down
                           C - Config (our ID received)
  AIS generation enabled:  Yes (level: 6, interval: 1s)
  Sending AIS:             Yes (to higher MEP, started 01:32:56 ago)
  Receiving AIS:           No
  
  Packet        Sent      Received
  ------  ----------  ----------------------------------------------------------
  CCM          12345         67890  (out of seq: 6, discarded: 10)
  LBM              5             0
  LBR              0             5  (out of seq: 0, with bad data: 0)
  AIS              0         46910
  LCK              -             0

Example 4: Detail

The following example shows how to display detailed statistics for MEPs in a domain service:

RP/0/RP0/CPU0:router# show ethernet cfm local meps detail
 
   
Domain foo (level 6), Service bar
Up MEP on GigabitEthernet0/1/0/0.234, MEP-ID 100
================================================================================
  Interface state: Up      MAC address: 1122.3344.5566
  Peer MEPs: 0 up, 0 with errors, 0 timed out (archived)
 
   
  CCM generation enabled:  No
  AIS generation enabled:  Yes (level: 7, interval: 1s)
  Sending AIS:             Yes (started 01:32:56 ago)
  Receiving AIS:           Yes (from lower MEP, started 01:32:56 ago)
 
   
Domain fred (level 5), Service barney 
Up MEP on GigabitEthernet0/1/0/0.234, MEP-ID 2
================================================================================
  Interface state: Up      MAC address: 1122.3344.5566
  Peer MEPs: 3 up, 2 with errors, 0 timed out (archived)
  Cross-check defects: 0 missing, 0 unexpected
 
   
  CCM generation enabled:  Yes (Remote Defect detected: Yes)
  CCM defects detected:    R - Remote Defect received
                           P - Peer port down
                           C - Config (our ID received)
  AIS generation enabled:  Yes (level: 6, interval: 1s)
  Sending AIS:             Yes (to higher MEP, started 01:32:56 ago)
  Receiving AIS:           No

EFD Configuration: Examples

The following example shows how to enable EFD:

RP/0/RP0/CPU0:router# configure 
RP/0/RP0/CPU0:router(config)# ethernet cfm 
RP/0/RP0/CPU0:router(config-cfm)# domain D1 level 1
RP/0/RP0/CPU0:router(config-cfm-dmn)# service S1 down-meps
RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# efd 
 
   

The following example shows how to enable EFD logging:

RP/0/RP0/CPU0:router# configure 
RP/0/RP0/CPU0:router(config)# ethernet cfm 
RP/0/RP0/CPU0:router(config-cfm)# domain D1 level 1
RP/0/RP0/CPU0:router(config-cfm-dmn)# service S1 down-meps
RP/0/RP0/CPU0:router(config-cfm-dmn-svc)# log efd 

Displaying EFD Information: Examples

The following examples show how to display information about EFD:

show efd interfaces Command: Example

show ethernet cfm local meps detail Command: Example

show efd interfaces Command: Example

The following example shows how to display all interfaces that are shut down in response to an EFD action:

RP/0/RP0/CPU0:router# show efd interfaces 
 
   
Server VLAN MA
==============
Interface         Clients
-------------------------
GigE0/0/0/0.0     CFM

show ethernet cfm local meps detail Command: Example

Use the show ethernet cfm local meps detail command to display MEP-related EFD status information. The following example shows that EFD is triggered for MEP-ID 100:

RP/0/RP0/CPU0:router# show ethernet cfm local meps detail
 
   
Domain foo (level 6), Service bar
Up MEP on GigabitEthernet0/1/0/0.234, MEP-ID 100
================================================================================
  Interface state: Up      MAC address: 1122.3344.5566
  Peer MEPs: 0 up, 0 with errors, 0 timed out (archived)
  Cross-check errors: 2 missing, 0 unexpected
 
   
  CCM generation enabled:  No
  AIS generation enabled:  Yes (level: 7, interval: 1s)
  Sending AIS:             Yes (started 01:32:56 ago)
  Receiving AIS:           Yes (from lower MEP, started 01:32:56 ago)
  EFD triggered:           Yes
 
   
Domain fred (level 5), Service barney 
Up MEP on GigabitEthernet0/1/0/0.234, MEP-ID 2
================================================================================
  Interface state: Up      MAC address: 1122.3344.5566
  Peer MEPs: 3 up, 0 with errors, 0 timed out (archived)
  Cross-check errors: 0 missing, 0 unexpected
 
   
  CCM generation enabled:  Yes (Remote Defect detected: No)
  AIS generation enabled:  Yes (level: 6, interval: 1s)
  Sending AIS:             No
  Receiving AIS:           No
  EFD triggered:           No

Note You can also verify that EFD has been triggered on an interface using the show interfaces and show interfaces brief commands. When an EFD trigger has occurred, these commands will show the interface status as up and the line protocol state as down.


Configuration Examples for Ethernet SLA

This section includes the following examples:

Ethernet SLA Profile Type Configuration: Examples

Ethernet SLA Probe Configuration: Examples

Profile Statistics Measurement Configuration: Examples

Scheduled SLA Operation Probe Configuration: Examples

Ethernet SLA Operation Probe Scheduling and Aggregation Configuration: Example

Ongoing Ethernet SLA Operation Configuration: Example

On-Demand Ethernet SLA Operation Basic Configuration: Examples

Ethernet SLA Y.1731 SLM Configuration: Examples

Ethernet SLA Show Commands: Examples

Ethernet SLA Profile Type Configuration: Examples

These examples show how to configure the different profile types supported by Ethernet SLA.

Example 1

This example configures a profile named "Prof1" for CFM loopback measurements:

configure
 ethernet sla 
  profile  Prof1 type cfm-loopback 
   commit

Example 2

This example configures a profile named "Prof1" for CFM delay measurements. Setting this type allows you to configure the probe to measure additional one-way delay and jitter statistics:

configure
 ethernet sla 
  profile  Prof1 type cfm-delay-measurement 
   commit

Ethernet SLA Probe Configuration: Examples

These examples show how to configure some of the packet options for an Ethernet CFM loopback probe.

Example 1

This example shows how to configure sending a group of 100 packets in 100 ms intervals and repeat that burst every 60 seconds. Packets are padded to a size of 9000 bytes as needed using a hexadecimal test pattern of "abcdabcd," and with a class of service value of 7:


Note The total length of a burst (packet count multiplied by the interval) must not exceed 1 minute.


configure
 ethernet sla 
  profile  Prof1 type cfm-loopback 
   probe 
    send burst every 60 seconds packet count 100 interval 100 milliseconds 
    packet size 9000 test pattern hex 0xabcdabcd
    priority 7 
    commit

Example 2

This example has the same characteristics as the configuration in Example 1, but sends a single burst of 50 packets, one second apart:

configure
 ethernet sla 
  profile  Prof1 type cfm-loopback 
   probe 
    send burst once packet count 50 interval 1 second 
    packet size 9000 test pattern hex 0xabcdabcd
    priority 7 
    commit

Example 3

This example shows how to configure a continuous stream of packets at 100 ms intervals for the duration of the probe. Packets are padded to a size of 9000 bytes as needed using a pseudo-random test pattern, and with a class of service value of 7:

configure
 ethernet sla 
  profile Prof1 type cfm-loopback 
   probe 
    send burst every 60 seconds packet count 600 interval 100 milliseconds 
    packet size 9000 test pattern pseudo-random
    priority 7 
    commit

Profile Statistics Measurement Configuration: Examples

These examples show how to configure the different types of statistics measurement.

Example 1

This example shows the two available types of statistics that can be measured by a CFM loopback SLA profile type:

configure
 ethernet sla 
  profile  Prof1 type cfm-loopback 
  statistics measure round-trip-delay 
  statistics measure round-trip-jitter
   commit

Example 2

This example shows how to configure measurement of round-trip delay and one-way jitter (from destination to source) for a CFM delay measurement SLA profile type:


Note The CFM delay measurement profile type supports measurement of all round-trip and one-way delay and jitter statistics.


configure
 ethernet sla 
  profile  Prof1 type cfm-delay-measurement 
  statistics measure round-trip-delay 
  statistics measure one-way-jitter-ds
   commit

Scheduled SLA Operation Probe Configuration: Examples

These examples show how to configure different schedules for an SLA operation probe.

Example 1

This example shows how to configure a probe to run hourly for a specified duration:

configure
 ethernet sla 
  profile  Prof1 type cfm-delay-measurement 
  schedule every 1 hours for 15 minutes
  commit

Example 2

This example shows how to configure a probe to run daily for a specified period of time:

configure
 ethernet sla 
  profile  Prof1 type cfm-delay-measurement 
  schedule every day at 11:30 for 5 minutes 
  commit

Example 3

This example shows how to configure a probe to run weekly beginning at a specified time and for a specified duration:

configure
 ethernet sla 
  profile  Prof1 type cfm-delay-measurement 
  schedule every week on Monday at 23:30 for 1 hour 
  commit

Ethernet SLA Operation Probe Scheduling and Aggregation Configuration: Example

Figure 13 shows a more comprehensive example of how some of the probe scheduling and measurement configuration works using aggregation. The following configuration supports some of the concepts shown in the figure:

configure
 ethernet sla profile Prof1 type cfm-loopback
  probe
   send packet every 60 seconds 
   schedule every 6 hours for 2 hours
   statistics measure round-trip-delay
    aggregate bins 3 width 30
    buckets size 2 per-probe
    buckets archive 4
    commit

Figure 13 SLA Probe Scheduling Operation With Bin Aggregation

This example schedules a probe with the following characteristics:

Sends packets 60 seconds apart (for a 2-hour probe, this results in sending 120 individual packets).

Probe runs every 6 hours for 2 hours duration.

Collects data into 2 buckets for every probe, so each bucket covers 1 hour of the 2-hour probe duration.

Aggregates statistics within the buckets into 3 bins each in the following ranges:

Bin 1 contains samples in the range 0 to < 30 ms.

Bin 2 contains samples in the range 30 ms to < 60 ms.

Bin 3 contains samples in the range 60 ms or greater (unbounded).

The last 4 buckets are saved in memory.

Ongoing Ethernet SLA Operation Configuration: Example

This example shows how to configure an ongoing Ethernet SLA operation on a MEP:

 interface gigabitethernet 0/1/0/1
  ethernet cfm 
  mep domain Dm1 service Sv1 mep-id 1 
  sla operation profile Profile_1 target mac-address 01:23:45:67:89:ab s
  commit 
  end

On-Demand Ethernet SLA Operation Basic Configuration: Examples

These examples show how to configure on-demand Ethernet SLA operations.

Example 1

This example shows how to configure a basic on-demand Ethernet SLA operation for a CFM loopback probe that by default will measure round-trip delay and round-trip jitter for a one-time, 10-second operation to the target MEP:

RP/0/RP0/CPU0:router# ethernet sla on-demand operation type cfm-loopback probe domain D1 
source interface TenGigE 0/6/1/0 target mep-id 1

Example 2

This example shows how to configure a basic on-demand Ethernet SLA operation for a CFM delay measurement probe that by default will measure one-way delay and jitter in both directions, as well as round-trip delay and round-trip jitter for a one-time, 10-second operation to the target MEP:

RP/0/RP0/CPU0:router# ethernet sla on-demand operation type cfm-delay-measurement probe 
domain D1 source interface TenGigE 0/6/1/0 target mep-id 1
 
   

Ethernet SLA Y.1731 SLM Configuration: Examples

These examples show how to configure the synthetic loss measurement statistics.

Example 1

This example shows the default configuration for Y.1731 SLM:

ethernet sla
  profile sl1 type cfm-synthetic-loss-measurement
    statistic measure one-way-loss-sd
    statistic measure one-way-loss-ds

Example 2

This example configures a profile named "Sl2" for synthetic loss measurements. with the parameters to configure the probe and SLM statistics:

 
   
ethernet sla
  profile sl2 type cfm-synthetic-loss-measurement
    probe
      send burst every 5 seconds packet count
                     100 interval 50 milliseconds
      packet size 400 test pattern hex 0xABDC1234
      synthetic loss calculation packets 200
    schedule every 1 hours for 1 minute
    statistic measure one-way-loss-sd
    statistic measure one-way-loss-ds
      aggregate bins 3 width 30
      bucket size 24 probes

Ethernet SLA Show Commands: Examples

These examples show how to display information about configured SLA operations:

show ethernet sla operations Command: Example 1

RP/0/RP0/CPU0:router# show ethernet sla operations interface gigabitethernet 0/1/0/1.1 
 
   
Interface GigabitEthernet0/1/0/1.1
Domain mydom Service myser to 00AB.CDEF.1234
-----------------------------------------------------------------------------
Profile 'business-gold'
Probe type CFM-delay-measurement:
    bursts sent every 1min, each of 20 packets sent every 100ms
    packets padded to 1500 bytes with zeroes
    packets use priority value of 7
Measures RTT: 5 bins 20ms wide; 2 buckets/ probe; 75/100 archived
Measures Jitter (interval 1): 3 bins 40ms wide; 2 buckets/probe; 50 archived
Scheduled to run every Sunday at 4am for 2 hours:
    last run at 04:00 25/05/2008

show ethernet sla configuration-errors Command: Example 2

RP/0/RP0/CPU0:router# show ethernet sla configuration-errors 
 
   
Errors:
-------
  Profile 'gold' is not defined but is used on Gi0/0/0/0.0
  Profile 'red' defines a test-pattern, which is not supported by the type
 
   

These examples show how to display the contents of buckets containing SLA metrics collected by probes:

show ethernet sla statistics current Command: Example 3

RP/0/RP0/CPU0:router# show ethernet sla statistics current interface GigabitEthernet 
0/0/0/0.0 
 
   
Interface GigabitEthernet 0/0/0/0.0
Domain mydom Service myser to 00AB.CDEF.1234
=============================================================================
Profile 'business-gold', packet type 'cfm-loopback'
Scheduled to run every Sunday at 4am for 2 hours
 
   
Round Trip Delay
~~~~~~~~~~~~~~~~
2 buckets per probe
 
   
Bucket started at 04:00 Sun 17 Feb 2008 lasting 1 hour:
    Pkts sent: 2342; Lost 2 (0%); Corrupt: 0 (0%); Misordered: 0 (0%)
    Min: 13ms; Max: 154ms; Mean: 28ms; StdDev: 11ms
 
   
Round Trip Jitter
~~~~~~~~~~~~~~~~~
2 buckets per probe
 
   
Bucket started at 04:00 Sun 17 Feb 2008 lasting 1 hour:
    Pkts sent: 2342; Lost: 2 (0%); Corrupt: 0 (0%); Misordered: 0 (0%)
    Min: -5ms; Max: 8ms; Mean: 0ms; StdDev: 3.6ms
 
   
Bucket started at 05:00 Sun 17 Feb 2008 lasting 1 hour:
    Pkts sent: 2342; Lost: 2 (0%); Corrupt: 0 (0%); Misordered: 0 (0%)
    Min: 0; Max: 4; Mean: 1.4; StdDev: 1

show ethernet sla statistics history detail Command: Example 4

RP/0/RP0/CPU0:router# show ethernet sla history detail GigabitEthernet 0/0/0/0.0 
 
   
Interface GigabitEthernet 0/0/0/0.0
Domain mydom Service myser to 00AB.CDEF.1234
===============================================================================
Profile 'business-gold', packet type 'cfm-loopback'
Scheduled to run every Sunday at 4am for 2 hours
 
   
Round Trip Delay
~~~~~~~~~~~~~~~~
2 buckets per probe
 
   
Bucket started at 04:00 Sun 17 Feb 2008 lasting 1 hour:
    Pkts sent: 2342; Lost: 2 (0%); Corrupt: 0 (0%); Misordered: 0 (0%)
    Min: 13ms, occurred at 04:43:29 on Sun 22 Aug 2010 UTC
    Max: 154ms, occurred at 05:10:32 on Sun 22 Aug 2010 UTC
    Mean: 28ms; StdDev: 11ms
 
   
    Results suspect as more than 10 seconds time drift detected
    Results suspect as scheduling latency prevented some packets being sent
 
   
    Samples:
    Time sent       Result  Notes     
    ------------  --------  ----------
    04:00:01.324      23ms            
    04:00:01.425      36ms            
    04:00:01.525         -  Timed Out 
    ...
 
   
Round Trip Jitter
~~~~~~~~~~~~~~~~~
2 buckets per probe
 
   
Bucket started at 04:00 Sun 17 Feb 2008, lasting 1 hour:
    Pkts sent: 2342; Lost: 2 (0%); Corrupt: 0 (0%); Misordered: 0 (0%)
    Min: -5ms; Max: 10ms; Mean: 0ms; StdDev: 3.6ms
 
   
    Samples:
    Time sent       Result  Notes     
    ------------  --------  ----------
    04:00:01.324         -            
    04:00:01.425      13ms            
    04:00:01.525         -  Timed out 
    ...

show ethernet sla statistics history detail on-demand: Example 5

This example shows how to display statistics for all full buckets for on-demand operations in detail:

RP/0/RP0/CPU0/router #show ethernet sla statistics history detail on-demand
 
   
Interface GigabitEthernet0/0/0/0.1
Domain mydom Service myser to 0123.4567.890A
=============================================================================
On-demand operation ID #1, packet type 'cfm-delay-measurement'
Started at 15:38 on 06 July 2010 UTC, runs every 1 hour for 1 hour
 
   
Round Trip Delay
~~~~~~~~~~~~~~~~
1 bucket per probe
 
   
Bucket started at 15:38 on Tue 06 Jul 2010 UTC, lasting 1 hour:
    Pkts sent: 1200; Lost: 4 (0%); Corrupt: 600 (50%); Misordered: 0 (0%)
    Min: 13ms, occurred at 15:43:29 on Tue 06 Jul 2010 UTC
    Max: 154ms, occurred at 16:15:34 on Tue 06 Jul 2010 UTC
    Mean: 28ms; StdDev: 11ms
 
   
    Bins:
    Range              Samples    Cum. Count      Mean
    ------------  ------------  ------------  --------
     0 - 20 ms       194 (16%)     194 (16%)      17ms
    20 - 40 ms       735 (61%)     929 (77%)      27ms
    40 - 60 ms       212 (18%)    1141 (95%)      45ms
    > 60    ms        55  (5%)    1196            70ms
 
   
Bucket started at 16:38 on Tue 01 Jul 2008 UTC, lasting 1 hour:
    Pkts sent: 3600; Lost: 12 (0%); Corrupt: 1800 (50%); Misordered: 0 (0%)
    Min: 19ms, occurred at 17:04:08 on Tue 06 Jul 2010 UTC
    Max: 70ms, occurred at 16:38:00 on Tue 06 Jul 2010 UTC
    Mean: 28ms; StdDev: 11ms
 
   
    Bins:
    Range              Samples    Cum. Count      Mean
    ------------  ------------  ------------  --------
     0 - 20 ms       194 (16%)     194 (16%)      19ms
    20 - 40 ms       735 (61%)     929 (77%)      27ms
    40 - 60 ms       212 (18%)    1141 (95%)      45ms
    > 60    ms        55  (5%)    1196            64ms
 
   

show ethernet sla statistics profile Command: Example 6

These examples show how to display statistics for synthetic loss measurement in detail:

RP/0/RSP0/CPU0:router#show ethernet sla statistics profile sl2 statistic one-way-loss-sd 
detail
 
   
Source: Interface GigabitEthernet0/0/0/0, Domain dom1
Destination: Target MAC Address 0002.0003.0005
================================================================================
Profile 'sl1', packet type 'cfm-synthetic-loss-measurement'
Scheduled to run every 1hr first at 00:50:00 UTC for 1min
Frame Loss Ratio calculated every 10s
 
   
One-way Frame Loss (Source->Dest)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1 probes per bucket
 
   
Bucket started at 04:50:00 PDT Thu 15 September 2012 lasting 1hr
    Pkts sent: 1200; Lost: 27 (2.25%); Corrupt: 0 (0.0%);
                   Misordered: 0 (0.0%); Duplicates: 0 (0.0%)
    Min: 0.00%, occurred at 04:50:50 PDT Thu 15 September 2011
    Max: 5.50%, occurred at 04:50:20 PDT Thu 15 September 2011
    Mean: 2.08%; StdDev: 1.99%; Overall: 2.08%
 
   
    Measurements:
    Time                     Result  Notes
    ----------  -------------------  ----------
    04:50:00.0    1.50% (3 of 200)
    04:50:10.0    2.00% (4 of 200)
    04:50:20.0    5.50% (11 of 200)
    04:50:30.0    3.00% (6 of 200)
    04:50:40.0    0.50% (1 of 200)
    04:50:50.0    0.00% (0 of 200)

In the example 6, the description of the statistics that indicate the lost count and overall FLR are Lost: 27 (2.25%) and Overall: 2.08%. The lost count means that 27 SLMs were lost out of 1200, but it might not be possible to determine in which direction they were lost. The overall FLR reports the overall loss in the Source to Destination direction.

 
   

show ethernet sla statistics profile Command: Example 7

RP/0/RSP0/CPU0:ios#show ethernet sla statistics profile sl2 statistic one-way-loss-ds 
detail
Source: Interface GigabitEthernet0/0/0/0, Domain dom1
Destination: Target MAC Address 0002.0003.0005
================================================================================
Profile 'sl2', packet type 'cfm-synthetic-loss-measurement'
Scheduled to run every 1hr first at 00:55:00 UTC for 1min
Frame Loss Ratio calculated every 10s
 
   
One-way Frame Loss (Dest->Source)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
24 probes per bucket
 
   
Bucket started at 04:55:00 PDT Thu 15 September 2012 lasting 1 day
    Pkts sent: 28800; Lost: 14691 (51.01%); Corrupt: 0 (0.0%);
                      Misordered: 0 (0.0%); Duplicates: 0 (0.0%)
    Min: 10.00%, occurred at 04:55:00 PDT Thu 15 September 2011
    Max: 68.80%, occurred at 06:55:00 PDT Thu 15 September 2011
    Mean: 52.5%; StdDev: 0.00%; Overall: 51.00%
 
   
    Bins:
    Range             Count  Cum. Count    Mean
    -----------  ----------  ----------  ------
      0 to  30%  20 (13.9%)  20 (13.9%)  21.00%
     30 to  60%  71 (49.3%)  91 (63.2%)  57.90%
     60 to 100%  49 (34.0%) 144 (100.0%) 62.00%

Where to Go Next

When you have configured an Ethernet interface, you can configure individual VLAN subinterfaces on that Ethernet interface.

For information about modifying Ethernet management interfaces for the shelf controller (SC), route processor (RP), and distributed RP, see the "Advanced Configuration and Modification of the Management Ethernet Interface on Cisco IOS XR Software" module later in this document.

For information about IPv6 see the Implementing Access Lists and Prefix Lists on
Cisco IOS XR Softwar
e module in the Cisco IOS XR IP Addresses and Services Configuration Guide.

Additional References

The following sections provide references related to implementing Gigabit, 10-Gigabit, and Fast Ethernet interfaces.

Related Documents

Related Topic
Document Title

Cisco IOS XR master command reference

Cisco IOS XR Master Commands List

Cisco IOS XR interface configuration commands

Cisco IOS XR Interface and Hardware Component Command Reference

Information about user groups and task IDs

Cisco IOS XR Interface and Hardware Component Command Reference

Information about configuring interfaces and other components on the Cisco CRS-1 Router from a remote Craft Works Interface (CWI) client management application

Cisco Craft Works Interface Configuration Guide


Standards

Standards
Title

IEEE 802.1ag

Connectivity Fault Management

ITU-T Y.1731 (July 2011)

OAM Functions and Mechansims for Ethernet Based Networks

MEF 16

Metro Ethernet Forum, Technical Specification MEF 16, Ethernet Local Management Interface (E-LMI), January 2006


MIBs

MIBs
MIBs Link

IEEE8021-CFM-MIB

To locate and download MIBs for selected platforms using
Cisco IOS XR Software, use the Cisco MIB Locator found at the following URL:

http://cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml


RFCs

RFCs
Title

No new or modified RFCs are supported by this feature, and support for existing RFCs has not been modified by this feature.


Technical Assistance

Description
Link

The Cisco Technical Support website contains thousands of pages of searchable technical content, including links to products, technologies, solutions, technical tips, and tools. Registered Cisco.com users can log in from this page to access even more content.

http://www.cisco.com/techsupport