Release Notes for the Cisco ASR 900 Series Routers
Release Notes for the Cisco ASR 900 Router
Downloads: This chapterpdf (PDF - 300.0KB) The complete bookPDF (PDF - 2.65MB) | The complete bookePub (ePub - 287.0KB) | Feedback

Table of Contents

Release Notes for the Cisco ASR 900 Router

Cisco ASR 903 Router Overview

Feature Navigator

Hardware Supported

Feature Set Table

Software Licensing Overview

Documentation Roadmap

Determining the Software Version

Upgrading to a New Software Release

Supported ROMmon Versions

Deferrals

Field Notices and Bulletins

MIB Support

MIB Documentation

Open Source License Notices

Release Notes for the Cisco ASR 900 Router

The Cisco ASR 903 Router runs the Cisco IOS XE software beginning with Release 3.5.0S. This document provides information about the IOS XE software release for the Cisco ASR 903 Router beginning with Release 3.6(0)S.


NoteFor information about Cisco IOS Release 3.5, see theRelease Notes for Cisco IOS XE Release 3S.


The following sections provide an overview of the Cisco ASR 903 Router and Cisco IOS XE releases:

Cisco ASR 903 Router Overview

The Cisco ASR 903 Router is a fully-featured routing platform designed for the cost-effective delivery of converged mobile and business services. With full redundancy, shallow depth, low power consumption and high service scale, this 3-rack-unit (3RU) router is optimized for small aggregation and remote point-of-presence (POP) applications. The Cisco ASR 903 Router provides a rich and scalable feature set of Legacy, Timing, Carrier Ethernet, Layer 2 VPN (L2VPN) and Layer 3 VPN (L3VPN) services in a compact package.

The Cisco ASR 903 Router is a fully modular platform with support for 6-Interface Modules (IMs), two Route Switch Processor (RSP) slots, two power supplies and redundant fans. Cisco offers a wide choice of LAN and WAN interfaces available in speeds ranging from nxDS0 to 10 Gigabit Ethernet. The design of the Cisco ASR 903 Router delivers in-box hardware redundancy for all hardware components and supports software redundancy with In Service Software Upgrade (ISSU) and Non-Stop Forwarding (NSF) support.

Feature Navigator

You can use Cisco Feature Navigator to find information about feature, platform, and software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn . An account on cisco.com is not required.

Hardware Supported

Table 1 Supported RSP and Interface Modules on Cisco ASR 903 Router

 

RSP Module
Interface Modules
Part Number
Slot
A900-RSP1A-55
A900-RSP1B-55

8-port Gigabit Ethernet SFP Interface Module (8X1GE)

A900-IMA8S

All

8-port Gigabit Ethernet RJ45 (Copper) Interface Module (8X1GE)

A900-IMA8T

1-port 10 Gigabit Ethernet XFP Interface Module (1X10GE)

A900-IMA1X

0-3

16 x T1/E1 Interface Module

A900-IMA16D

All

4-Port OC3/STM-1 (OC-3) or 1-Port OC12/STM-4 (OC-12) Interface Module

A900-IMA4OS

14-port Serial Interface Module

A900-IMASER14A/S

A900-RSP2A-128

8-port Gigabit Ethernet SFP Interface Module (8X1GE)

A900-IMA8S

All

8-port Gigabit Ethernet RJ45 (Copper) Interface Module (8X1GE)

A900-IMA8T

1-port 10 Gigabit Ethernet XFP Interface Module (1X10GE)

A900-IMA1X

16 x T1/E1 Interface Module

A900-IMA16D

4-Port OC3/STM-1 (OC-3) or 1-Port OC12/STM-4 (OC-12) Interface Module

A900-IMA4OS

SFP Combo IM—8-port Gigabit Ethernet (8X1GE) +

1-port 10 Gigabit Ethernet (1X10GE)

A900-IMA8S1Z

Copper Combo IM—8-port Gigabit Ethernet (8X1GE)

+ 1-port 10 Gigabit Ethernet Interface Module(1X10GE)

A900-IMA8T1Z

2-port 10 Gigabit Ethernet Interface Module(2X10GE)

A900-IMA2Z

A900-RSP2A-64

1-port 10 Gigabit Ethernet XFP Interface Module (1X10GE)

A900-IMA1X

0-2

2-port 10 Gigabit Ethernet Interface Module (2X10GE)

A900-IMA2Z

4-Port OC3/STM-1 (OC-3) or 1-Port OC12/STM-4

(OC-12) Interface Module

A900-IMA4OS

8-port Gigabit Ethernet SFP Interface Module (8X1GE)

A900-IMA8S

3-5

8-port Gigabit Ethernet RJ45 (Copper) Interface Module

(8X1GE)

A900-IMA8T

16 x T1/E1 Interface Module

A900-IMA16D


Note • The combination IMs (A900-IMA8S1Z, A900-IMA8T1Z), and the A900-IMA2Z are not supported on the A900-RSP1A-55 and A900-RSP1B-55 modules on the Cisco ASR 903 Router.

  • The combination IMs (A900-IMA8S1Z, A900-IMA8T1Z) are not supported on the A900-RSP2-64 RSP module on the Cisco ASR 903 Router.


 

Table 2 Supported RSP and Interface Modules on Cisco ASR 902 Router

 

RSP Module
Interface Modules
Part Number
Slot
A900-RSP1A-55
A900-RSP1B-55

8-port Gigabit Ethernet SFP Interface Module (8X1GE)

A900-IMA8S

All

8-port Gigabit Ethernet RJ45 (Copper) Interface Module (8X1GE)

A900-IMA8T

1-port 10 Gigabit Ethernet XFP Interface Module (1X10GE)

A900-IMA1X

0 to 3

16 x T1/E1 Interface Module

A900-IMA16D

All

4-Port OC3/STM-1 (OC-3) or 1-Port OC12/STM-4 (OC-12) Interface Module

A900-IMA4OS

A900-RSP2A-128

8-port Gigabit Ethernet SFP Interface Module (8X1GE)

A900-IMA8S

All

8-port Gigabit Ethernet RJ45 (Copper) Interface Module (8X1GE)

A900-IMA8T

1-port 10 Gigabit Ethernet XFP Interface Module (1X10GE)

A900-IMA1X

SFP Combo IM—8-port Gigabit Ethernet (8X1GE) +

1-port 10 Gigabit Ethernet (1X10GE)

A900-IMA8S1Z

Copper Combo IM—8-port Gigabit Ethernet (8X1GE)

+ 1-port 10 Gigabit Ethernet Interface Module(1X10GE)

A900-IMA8T1Z

2-port 10 Gigabit Ethernet Interface Module(2X10GE)

A900-IMA2Z

A900-RSP2A-64

8-port Gigabit Ethernet SFP Interface Module (8X1GE)

A900-IMA8S

0 and 2

8-port Gigabit Ethernet RJ45 (Copper) Interface Module (8X1GE)

A900-IMA8T

1-port 10 Gigabit Ethernet XFP Interface Module (1X10GE)

A900-IMA1X

16 x T1/E1 Interface Module

A900-IMA16D

4-Port OC3/STM-1 (OC-3) or 1-Port OC12/STM-4 (OC-12) Interface Module

A900-IMA4OS

SFP Combo IM—8-port Gigabit Ethernet (8X1GE) +

1-port 10 Gigabit Ethernet (1X10GE)

A900-IMA8S1Z

Copper Combo IM—8-port Gigabit Ethernet (8X1GE)

+ 1-port 10 Gigabit Ethernet Interface Module(1X10GE)

A900-IMA8T1Z

2-port 10 Gigabit Ethernet Interface Module(2X10GE)

A900-IMA2Z

1-port 10 Gigabit Ethernet XFP Interface Module (1X10GE)

A900-IMA1X

1

2-port 10 Gigabit Ethernet Interface Module (2X10GE)

A900-IMA2Z

4-Port OC3/STM-1 (OC-3) or 1-Port OC12/STM-4

(OC-12) Interface Module

A900-IMA4OS

8-port Gigabit Ethernet SFP Interface Module (8X1GE)

A900-IMA8S

3

8-port Gigabit Ethernet RJ45 (Copper) Interface Module

(8X1GE)

A900-IMA8T

16 x T1/E1 Interface Module

A900-IMA16D

Feature Set Table

The following is the list of supported features per Cisco IOS Release on the Cisco A900-RSP1-55 RSP module.

Table 3 Supported Software Features for A900-RSP1-55

 

Cisco IOS XE Release
Supported Software Features

3.5

  • MPLS-TP: MS-PW with Static and Dynamic PW Support
  • REP Configurable Timers aka REP Fast Hellos
  • SSO Support for REP Fast Hello
  • Egress policing and marking
  • QoS ACLs for ASR900
  • MPLS OAM Support for Multisegment Pseudowires
  • Resilient Ethernet Protocol-no-edge-neighbor-enhancement
  • PIM version 2 support

3.6

  • ASR903 ATM/IMA/PPP/MLPPP Support on OC3 Interface Module
  • ACFC and PFC support on Multilink interface
  • 1588 BC over MPLS
  • PPP MLP MRRU negotiation configuration
  • EFP aware QoS
  • Switch Port Analyzer (SPAN)

3.7

  • BFD: BGP multihop client Support (IPv4/IPv6)
  • MLPPP Egress QoS Support
  • L2VPN Protocol Based CLI
  • N:1 PVC mapping to PWE with non-unique VPI (ATMCOMMON)
  • E2E Transparent Clocking
  • PPP MLP MRRU negotiation configuration
  • Any Transport over MPLS (AToM): Layer 2 QoS (Quality of Service)
  • Hybrid Clocking Support
  • ASR903 ATM/IMA/PPP/MLPPP Support on OC3 Interface Module
  • Channelization support for OC3 IM
  • 1588 PTP Best Master Clock Algorithm (BMCA) a.k.a. PTP Redundancy
  • Time of Day Selection
  • 1588 BC over MPLS
  • SR/MR APS for OC12 port on OC3/OC12 IM
  • ACFC and PFC support on Multilink interface
  • IPv6 ACL
  • MQC - Multi-Level Priority Queue
  • EFP aware QoS
  • DAI (Dynamic ARP Inspection)
  • DHCP Snooping
  • MAC Address Security for EVC Bridge-Domain
  • DHCP Option 82 Configurable Circuit ID and Remote ID
  • GOLD - Generic Online Diagnostics
  • Onboard Failure Logging
  • MFI -Extended LFA
  • MPLS VPN - Inter-Autonomous System Support
  • Hot Standby Pseudowire Support for ATM and TDM Access Circuits
  • BGP: Graceful Shutdown (GSHUT)
  • Switch Port Analyzer (SPAN)
  • MAC Limiting per VFI and BD
  • CFM Support on Trunk EFP
  • Static MAC binding to EVCs and Psuedowires
  • Link Path Through

3.8

  • BFD over TDM Routed
  • Offloading IPv4 Async BFD sessions with 3.3ms timers
  • IS-IS Support for BFD over IPv6
  • BFD Support for HSRP
  • MPLS-TP MIB
  • MPLS -TP: IP Less trace support (NodeId, LinkId)
  • IPSLA Y1731 SLM Feature Enhancements
  • MLPPP Egress QoS Support
  • Unicast Reverse Path Forwarding (uRPF) Loose mode
  • Egress default queue limit improvement and percent bandwidth support
  • MPLS over POS Support
  • QoS Support on POS on OC3 IM
  • POS Concatenation mode on STM1/4 IM
  • ASR-903: Multicast on T1/E1 & OC3 IMs
  • SR/MR APS for OC12 port on OC3/OC12 IM
  • MPLS-TP: ATM and TDM Pseudowires
  • Inverse Multiplexing over ATM (IMA)
  • Sonet Framing Support on OC3 IM
  • ITU-T Telecom Profile G.8265.1
  • MPLS-TP: ATM and TDM Pseudowires
  • G.8032 and CFM support for Microwave Adaptive Bandwidth
  • EtherChannel Min-Links
  • LACP 1-1 redundancy with fast switchover
  • VPLS BGP Signaling
  • BGP PIC (edge & core) - for RFC-3107 labeled iBGP
  • BGP Support for TCP Path MTU Discovery per Session
  • Remote satellite client node
  • Y.1731 enhancements (On-demand & Concurrent support)
  • Ethernet Local Management Interface (LMI) at Provider Edge (PE)
  • Synthetic Frame Loss Measurement (ETH-SLM)
  • Trunk EFP Support on Ether-Channel Interfaces

3.9

  • Embedded Event Manager (EEM) 4.0
  • BFD Echo Mode
  • QoS Classification based on EFP
  • MPLS -TP: Linear Protection/PSC support
  • QoS: Global CLI for CoS to EXP table mapping
  • QoS EXP Marking for Ingress on TDM and ATM PW
  • QoS Support for Ether Channels
  • QoS Classification based on EFP
  • L2VPN Protocol Base CLIs
  • PTP over Native Ethernet
  • Microwave ACM Signaling and EEM integration
  • MVPN
  • Enhanced Tracking Support / Enhanced Object Tracking / EOT
  • QoS on Serial TDM interface
  • OC12 Support for HDLC and MLPPP
  • POS (Packet over SONET/SDH) on OC12 IM card
  • MPLS - Multilink PPP support
  • 100BaseZX SFP
  • BGP Support for 4-byte ASN
  • IP FRR/Remote LFA FRR with L2VPN
  • CFM Support on Trunk EFP
  • IEEE 802.1ab LLDP (Link Layer Discovery Protocol)

3.10

  • Access Circuit Redundancy
  • Access Switch Device Manager Template
  • Auto-IP
  • BFD Debug Enhancement
  • Bidirectional Forwarding Detection Deterministic Hardware Offload
  • Broadcast and Multicast Suppression
  • IGMP Snooping
  • Licensing the OC-3 and OC-12 Interface Modules
  • Multichassis LACP
  • Pseudowire Group Switchover
  • Raw Socket
  • Remote LFA FRR Protection for TDM and ATM Pseudowires
  • Remote LFA FRR and Labeled BGP PIC FRR Integration
  • VPLS over Remote LFA

3.11

  • AAL5 termination
  • Access Switch Device Manager Template
  • Data Plane Ethernet Loopback with QoS
  • Dissimilar PHB Match at Ingress and Egress
  • Dying Gasp
  • DS3 Framing on OC-3 and OC-12
  • Fast Reroute Support for Bridge Domain Interface
  • BGP PIC Support for Bridge Domain Interface with FRR
  • IPv6 Multicast: Multicast Listener Discovery (MLD)
  • IPv6 Multicast: PIM v6
  • ISIS and OSPF Local Microloop Protection
  • MR-APS Integration with Hotstandby Pseudowire
  • Remote SPAN
  • Service Groups
  • TCAM Threshold Based Alarms

3.12

  • IP SLAs TWAMP Responder
  • Network Time Protocol (NTP) Timestamping
  • Auto-IP for SVI, Port Channel and VRF
  • Autonomic Networking
  • BGP Accumulated IGP
  • TWAMP Responder with RFC Compliance

3.13

  • Clear-Channel ATM
  • 802.1ad
  • Callhome V2 enhancements
  • UniDirectional Link Detection (UDLD)
  • REP Access Gateway Enhancements

Table 4 Supported Software Features for A900-RSP2

 

Cisco IOS XE Release
Technology
Supported Features

3.13

Ethernet OAM

  • 802.1ad
  • CFM Extension for 1+1 Hot-Standby Support
  • CFM over EFP interface configured with Cross connect
  • CFM Support on Trunk EFP
  • CFM enhancements
  • CFM CCM Hardware Offload
  • EtherChannel Mini-Links
  • Ethernet Local Management Interface (LMI) at Provider Edge (PE)
  • Ethernet Operations, Administration, and Maintenance (OAM)
  • Microwave ACM Signaling and EEM integration Synthetic Frame Loss Measurement (ETH-SLM)
  • Trunk EFP Support on Ether-Channel Interfaces
  • Y.1731 enhancements (On-demand & Concurrent support)
  • Y.1731 Performance Monitoring

3.13

Ethernet

  • 802.1ad
  • G.8032 and CFM support for Microwave Adaptive Bandwidth
  • IEEE 802.1ab LLDP (Link Layer Discovery Protocol)
  • IEEE 802.3ad Link Aggregation (LACP)
  • LACP 1-1 redundancy with fast switchover)
  • L2 ACL on Service Instance on Port-channel
  • MAC Address Limiting on Service Instance / Bridge Domain
  • MAC Address Security for EVC Bridge-Domain
  • MAC Limiting per VFI and BD
  • MST on EVC Bridge-Domain
  • Static MAC binding to EVCs and Psuedowires
  • Trunk EFP support
  • Unicast Reverse Path Forwarding (uRPF)
  • Unicast Reverse Path Forwarding (uRPF) Loose mode
  • UniDirectional Link Detection (UDLD)
  • Egress default queue limit improvement and percent bandwidth support
  • Switch Port Analyzer (SPAN)

IP Addressing

  • DAI (Dynamic ARP Inspection)
  • DHCP - DHCPv6 Relay Agent notification for Prefix Delegation
  • DHCP Option 82 Configurable Circuit ID and Remote ID
  • DHCP Snooping
  • DHCPv6 - Relay chaining for Prefix Delegation

IP Multicast

  • IGMP State Limit
  • Multicast Source Discovery Protocol (MSDP)
  • PIM Version 2
  • Source Specific Multicast (SSM)
  • Source Specific Multicast (SSM) Mapping

3.13

IP Routing

  • BFD - Static Route Support
  • BFD Echo Mode
  • BFD IPv6 Encapsulation Support
  • BFD Support for HSRP
  • BFD: BGP multihop client Support (IPv4/IPv6)
  • BFD - BFD Hardware Offload Support
  • SSO - BFD
  • OSPF Support for BFD over IPv4
  • BGP - iBGP NSR
  • BGP Support for BFD
  • BGP Support for TCP Path MTU Discovery per Session
  • BGP: Graceful Shutdown (GSHUT)
  • BGP PIC (edge & core) - for RFC-3107 labeled iBGP
  • BGP Support for 4-byte ASN
  • Cisco-BGP-MIBv2
  • IP 16-way Equal-Cost Multipath
  • IP FRR
  • IP FRR/Remote LFA FRR with L2VPN
  • IS-IS - MPLS LDP Autoconfiguration
  • IS-IS Support for BFD over IPv4
  • Multi-protocol BGP (MP-BGP) - MPLS VPN
  • VPLS BGP Signaling

IP Tunneling

  • L2PT - Layer 2 Protocol Tunneling
  • L2PT - Layer 2 Protocol Tunneling on Trunk Ports

IP Routing- Version 6

  • IPv6 ACL
  • IPv6 QoS: MQC Packet Classification
  • IPv6 Routing: Static Routing IPv6 Switching: CEF/dCEF Support
  • IPv6 Switching: Provider Edge Router over MPLS (6PE)
  • IPv6 Routing: IS-IS Support for IPv6
  • IPv6 Routing: OSPF for IPv6 (OSPFv3)
  • IPv6 VPN over MPLS (6VPE)
  • Static Route Support for BFD over IPv6

3.13

MPLS

  • Any Transport over MPLS (AToM): Ethernet over MPLS (EoMPLS)
  • BGP PIC Edge for IP/MPLS
  • Bidirectional MPLS-TP LSP
  • H-VPLS N-PE Redundancy for MPLS Access
  • Hot Standby Pseudowire Support for ATM and TDM Access Circuits
  • L2VPN Protocol Based CLI
  • Link Path Through
  • MFI -Extended LFA
  • MPLS (Multiprotocol Label Switching)
  • MPLS -TP: IP Less trace support (NodeId, LinkId)
  • MPLS -TP: Linear Protection/PSC support
  • MPLS Forwarding Infrastructure Scalability
  • MPLS LDP - IGP Synchronization
  • MPLS OAM Support for Multisegment Pseudowires
  • MPLS TE - Bundled Interface Support (EtherChannel and MLP)
  • MPLS TP: IP-less configuration of MPLS TP tunnels
  • MPLS Traffic Engineering (TE) - Fast Reroute (FRR) Link and Node Protection
  • MPLS Virtual Private Networks (VPN)
  • MPLS VPN - Inter-Autonomous System Support
  • MPLS-TP OAM: Continuity Check via BFD
  • MPLS-TP OAM: Fault Management
  • MPLS-TP OAM: GACH
  • MPLS-TP OAM: Ping/Trace
  • MPLS-TP Path Protection
  • Static VPLS over MPLS-TP
  • Support sending PW Grouping ID TLV
  • Virtual Private LAN Services (VPLS)
  • VPLS Autodiscovery, BGP-based
  • VPLS MAC Address Withdrawal
  • VPLS over MPLS-TP
  • MPLS-TP: MS-PW with Static and Dynamic PW Support
  • MPLS-TP: PW Redundancy for Static PWs
  • L2VPN Static to Dynamic PW Interconnection & PW Preferred Path for MPLS-TP Tunnels
  • L2VPN: PW Status for Static PWs

3.13

Network Management

  • IPSLA Y1731 SLM Feature Enhancements

OS Infrastructure

  • Access Switch Device Manager (SDM) Template
  • Cisco Secure Licensing Support)
  • Field Programmable Device Upgrade Tool
  • Punt Policing and Monitoring
  • Digital Code Signing
  • Embedded Event Manager (EEM) 4.0

QoS

  • Class based policing
  • Class Based Weighted Fair Queuing (CBWFQ)
  • Class-based QoS MIB
  • Diffserv Compliant WRED
  • EFP aware QoS
  • Egress policing and marking
  • match any classification
  • Modular QoS CLI (MQC)
  • MQC - Multi-Level Priority Queue
  • Port-Shaper and LLQ in the presence of EFPs
  • QoS ACLs for ASR900
  • QoS Classification based on EFP
  • QoS EXP matching
  • QoS Packet Marking
  • RSVP - Resource Reservation Protocol

3.13

Security

  • ACL - Access Control List Source and Destination Address Matching
  • ACL - DSCP Matching
  • ACL - ICMP Code
  • ACL - IP Protocol
  • Secure Shell SSH Version 2 Client Support

Timing and Clocking

  • 1588 BC over MPLS
  • 1588 PTP Best Master Clock Algorithm (BMCA) or PTP Redundancy
  • 1588-2008 Boundary Clock
  • E2E Transparent Clocking
  • Hybrid Clocking Support
  • ITU-T Telecom Profile G.8265.1
  • Support for IEEE 1588-2008 Precision Clock Synchronization Protocol
  • Time of Day Selection
  • PTP over Native Ethernet

Software Licensing Overview

The Cisco ASR 903 Router offers the following base licenses:

  • Metro Services
  • Metro IP Services
  • Metro Aggregation Services

Table 5 Cisco ASR 900 Software Licenses Feature Set

 

Metro Services
Metro IP Services
Metro Aggregation Services

 

Includes all features in Metro Services

Includes all features in Metro IP Services

QoS, with deep buffers and hierarchical QoS (HQOS)

IP routing (RIP, OSPF, EIGRP, BGP, IS-IS)

MPLS (LDP and VPN)

Layer 2: 802.1d, 802.1q

PIM (SM, DM, SSM), SSM mapping

MPLS TE and FRR

Ethernet Virtual Circuit (EVC)

BFD

MPLS OAM

Ethernet OAM (802.1ag, 802.3ah)

Multi-VRF CE (VRF lite) with service awareness (ARP, ping, SNMP, syslog, trace-route, FTP, TFTP)

MPLS-TP

Multiple Spanning Tree (MST) and Resilient Ethernet Protocol (REP)

IEEE 1588-2008 Ordinary Clock and Transparent Clock

Pseudowire emulation (EoMPLS, CESoPSN, and SAToP)

Synchronous Ethernet

 

VPLS and HVPLS

IPv4 and IPv6 host connectivity

 

Pseudowire redundancy

 

 

MR-APS and mLACP

The Cisco ASR 903 Router offers the following additional feature licenses:

  • ATM
  • IEEE 1588-2008 Boundary Clock/Master Clock
  • OC-3 Port License

NoteThese features require a software license to use.


For more information about each software license including part numbers, see the Cisco ASR 903 Router Datasheet . For instructions on how to install licenses on the Cisco ASR 903 Router, see the Software Activation Configuration Guide, Cisco IOS XE Release 3S .

Documentation Roadmap

To view other documents for the Cisco ASR 903 Router, see the Cisco ASR 903 Router Documentation Roadmap .

Determining the Software Version

You can use the following commands to verify your software version:

  • Consolidated Package— show version
  • Individual sub-packages— show version installed (lists all installed packages)

Upgrading to a New Software Release

Only Cisco IOS XE 3S consolidated packages can be downloaded from Cisco.com; users who want to run the router using individual subpackages must first download the image from Cisco.com and extract the individual subpackages from the consolidated package.

For information about upgrading to a new software release, see the Cisco ASR 903 Router Chassis Software Configuration Guide at http://www.cisco.com/en/US/docs/routers/asr903/software/guide/chassis/Release3.7.0S/ASR903-Chassis-SW-39.html .

Supported ROMmon Versions

15.3(2r)S is the recommended ROMmon version for IOS XE 3.5, 3.6, 3.7, 3.8, and 3.9 software releases.

Deferrals

Cisco IOS software images are subject to deferral. We recommend that you view the deferral notices at the following location to determine whether your software release is affected:

http://www.cisco.com/en/US/products/products_security_advisories_listing.html

Field Notices and Bulletins

MIB Support

This section describes the MIB support on the Cisco ASR 903 Router.

  • Table 6 summarizes the supported MIBs on the Cisco ASR 903 Router:

 

Table 6 Supported MIBs

Supported MIBs

BGP4-MIB (RFC 1657)

CISCO-IMAGE-LICENSE-MGMT-MIB

MPLS-LDP-STD-MIB (RFC 3815)

CISCO-BGP-POLICY-ACCOUNTING-MIB

CISCO-IMAGE-MIB

MPLS-LSR-STD-MIB (RFC 3813)

CISCO-BGP4-MIB

CISCO-IPMROUTE-MIB

MPLS-TP-MIB

CISCO-BULK-FILE-MIB

CISCO-LICENSE-MGMT-MIB

MSDP-MIB

CISCO-CBP-TARGET-MIB

CISCO-MVPN-MIB

NOTIFICATION-LOG-MIB (RFC 3014)

CISCO-CDP-MIB

CISCO-NETSYNC-MIB

OSPF-MIB (RFC 1850)

CISCO-CEF-MIB

CISCO-OSPF-MIB (draft-ietf-ospf-mib-update-05)

OSPF-TRAP-MIB (RFC 1850)

CISCO-CLASS-BASED-QOS-MIB

CISCO-OSPF-TRAP-MIB (draft-ietf-ospf-mib-update-05)

PIM-MIB (RFC 2934)

CISCO-CONFIG-COPY-MIB

CISCO-PIM-MIB

RFC1213-MIB

CISCO-CONFIG-MAN-MIB

CISCO-PROCESS-MIB

RFC2982-MIB

CISCO-DATA-COLLECTION-MIB

CISCO-PRODUCTS-MIB

RMON-MIB (RFC 1757)

CISCO-EMBEDDED-EVENT-MGR-MIB

CISCO-PTP-MIB

RSVP-MIB

CISCO-ENHANCED-MEMPOOL-MIB

CISCO-RF-MIB

SNMP-COMMUNITY-MIB (RFC 2576)

CISCO-ENTITY-ALARM-MIB

CISCO-RTTMON-MIB

SNMP-FRAMEWORK-MIB (RFC 2571)

CISCO-ENTITY-EXT-MIB

CISCO-SONET-MIB

SNMP-MPD-MIB (RFC 2572)

CISCO-ENTITY-FRU-CONTROL-
MIB

CISCO-SYSLOG-MIB

SNMP-NOTIFICATION-MIB (RFC 2573)

CISCO-ENTITY-SENSOR-MIB

DS1-MIB (RFC 2495)

SNMP-PROXY-MIB (RFC 2573)

CISCO-ENTITY-VENDORTYPE-OID-MIB

ENTITY-MIB (RFC 4133)

SNMP-TARGET-MIB (RFC 2573)

CISCO-FLASH-MIB

ENTITY-SENSOR-MIB (RFC 3433)

SNMP-USM-MIB (RFC 2574)

CISCO-FTP-CLIENT-MIB

ENTITY-STATE-MIB

SNMPv2-MIB (RFC 1907)

CISCO-IETF-ISIS-MIB

EVENT-MIB (RFC 2981)

SNMPv2-SMI

CISCO-IETF-PW-ATM-MIB

ETHERLIKE-MIB (RFC 3635)

SNMP-VIEW-BASED-ACM-MIB
(RFC 2575)

CISCO-IETF-PW-ENET-MIB

IF-MIB (RFC 2863)

SONET-MIB

CISCO-IETF-PW-MIB

IGMP-STD-MIB (RFC 2933)

TCP-MIB (RFC 4022)

CISCO-IETF-PW-MPLS-MIB

IP-FORWARD-MIB

TUNNEL-MIB (RFC 4087)

CISCO-IETF-PW-TDM-MIB

IP-MIB (RFC 4293)

UDP-MIB (RFC 4113)

CISCO-IF-EXTENSION-MIB

IPMROUTE-STD-MIB (RFC 2932)

 

CISCO-IGMP-FILTER-MIB

MPLS-LDP-GENERIC-STD-MIB (RFC 3815)

 

Table 7 summarizes the unverified and supported MIBs on the Cisco ASR 903 Router.

 

Table 7 Unverified and Supported MIBs

Unverified MIBs

ATM-MIB

CISCO-IETF-DHCP-SERVER-EXT-MIB

EXPRESSION-MIB

CISCO-ATM-EXT-MIB

CISCO-IETF-MPLS-TE-P2MP-STD-MIB

HC-ALARM-MIB

CISCO-ATM-IF-MIB

CISCO-IETF-PPVPN-MPLS-VPN-MIB

HC-RMON-MIB

CISCO-ATM-PVC-MIB

CISCO-IP-STAT-MIB

IEEE8021-CFM-MIB

CISCO-ATM-PVCTRAP-EXTN-MIB

CISCO-IPSLA-ETHERNET-MIB

IEEE8021-CFM-V2-MIB

CISCO-BCP-MIB

CISCO-L2-CONTROL-MIB

IEEE8023-LAG-MIB

CISCO-CALLHOME-MIB

CISCO-LAG-MIB

INT-SERV-GUARANTEED-MIB

CISCO-CIRCUIT-INTERFACE-MIB

CISCO-MAC-NOTIFICATION-MIB

INTEGRATED-SERVICES-MIB

CISCO-CONTEXT-MAPPING-MIB

CISCO-MEMORY-POOL-MIB

MPLS-L3VPN-STD-MIB (RFC 4382)

CISCO-EIGRP-MIB

CISCO-NHRP-EXT-MIB

MPLS-LDP-ATM-STD-MIB
(RFC 3815)

CISCO-ERM-MIB

CISCO-NTP-MIB

MPLS-LDP-MIB

CISCO-ETHER-CFM-MIB

CISCO-PING-MIB

MPLS-TE-STD-MIB

CISCO-ETHERLIKE-EXT-MIB

CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB

MPLS-VPN-MIB

CISCO-EVC-MIB

CISCO-RTTMON-ICMP-MIB

NHRP-MIB

CISCO-HSRP-EXT-MIB

CISCO-RTTMON-IP-EXT-MIB

RFC2006-MIB (MIP)

CISCO-HSRP-MIB

CISCO-RTTMON-RTP-MIB

RMON2-MIB (RFC 2021)

CISCO-IETF-ATM2-PVCTRAP-MIB

CISCO-SNMP-TARGET-EXT-MIB

SMON-MIB

CISCO-IETF-ATM2-PVCTRAP-MIB-EXTN

CISCO-TCP-MIB

VRRP-MIB

CISCO-IETF-BFD-MIB

CISCO-VRF-MIB

 

CISCO-IETF-DHCP-SERVER-MIB

ETHER-WIS (RFC 3637)

 

MIB Documentation

The following resources provide more detail about MIBs on the Cisco ASR 903 Router:

  • Cisco ASR 903 Router MIB Guide—For information about the Cisco ASR 903 Series Router product implementation of the MIB protocol, see Cisco ASR 903 Series Aggregation Services Router MIB Specifications Guide at the following location:

http://www.cisco.com/en/US/docs/wireless/asr_900/mib/guide/asr903mib.html

  • MIB Locator—To locate and download MIBs for selected platforms, Cisco IOS and Cisco IOS XE releases, and feature sets, use Cisco MIB Locator found at the following location:

http://tools.cisco.com/ITDIT/MIBS/servlet/index

To access Cisco MIB Locator, you must have an account on Cisco.com. If you have forgotten or lost your account information, send a blank e-mail to cco-locksmith@cisco.com. An automatic check will verify that your e-mail address is registered with Cisco.com. If the check is successful, account details with a new random password will be e-mailed to you. Qualified users can establish an account on Cisco.com by following the directions found at the following location:

http://tools.cisco.com/RPF/register/register.do

Open Source License Notices

For a listing of the license notices for open source software used in Cisco IOS XE 3S Releases, see the documents accessible from the License Information page at the following location:

http://www.cisco.com/en/US/products/ps11174/products_licensing_information_listing.html