Cisco ASR 9000 Series Aggregation Services Router System Management Command Reference, Release 5.2.x
Hardware Redundancy and Node Administration Commands on the Cisco IOS XR Softwarethe Cisco ASR 9000 Series Router
Downloads: This chapterpdf (PDF - 2.2MB) The complete bookPDF (PDF - 10.2MB) | Feedback

Hardware Redundancy and Node Administration Commands on the Cisco IOS XR Softwarethe Cisco ASR 9000 Series Router

Contents

Hardware Redundancy and Node Administration Commands on the Cisco IOS XR Softwarethe Cisco ASR 9000 Series Router

This module describes the commands used to manage the hardware redundancy, power, and administrative status of the nodes on a router running Cisco IOS XR software.

clear canbus

To clear the counters used for statistics regarding the CAN bus, use the clear canbus command in administration EXEC mode.

clear canbus { client-stats | controller-stats | server-stats } location { all | node-id }

Syntax Description

client-stats

Clears CAN bus client statistics.

controller-stats

Clears CAN bus controller statistics.

server-stats

Clears CAN bus server statistics.

location {all | node-id}

Clears the CAN bus statistics for a specific node or all nodes.

Command Default

None

Command Modes

Administration EXEC

Command History

Release Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation

sysmgr

read

Examples

The following example illustrates how to use the clear canbus command:

RP/0/0RP0RSP0/CPU0:router(admin)# clear canbus server-stats location all

Related Commands

Command

Description

show canbus

Displays the statistics regarding the CAN bus.

clear mbus-statistics location

To clear Mbus firmware statistics on a specific node, use the clear mbus-statistics location command in administration EXEC mode.

clear mbus-statistics location { node-id | all }

Syntax Description

node-id

Identifies the location of the node whose Mbus interface counters you want to clear. The node-id is expressed in the rack/slot/module notation.

Note   

Enter the show platform command to see the location of all nodes installed in the router.

all

Clears Mbus interface counters for all nodes installed in the router.

Command Default

No default behavior or values

Command Modes

Administration EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

sysmgr

execute

Examples

The following example shows how to clear all Mbus interface counters on a specific node:

RP/0/0/CPU0:router# admin
RP/0/0/CPU0:router(admin)# clear mbus-statistics location 0/0/CPU0
                       

clear plugin slot counts

To clear the running counts of the backplane connector slot plugins, use the clear plugin slot counts command in administration EXEC mode.

clear plugin slot counts location node-id

Syntax Description

location node-id Clears plugin slot counts on the designated node. The node-id argument is expressed in the rack/slot/module notation.

Command Default

None

Command Modes

Administration EXEC

Command History

Release Modification

Release 3.9.1

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The clear plugin slot counts command can be used only if the revised backplane ID card (BPID-02) is installed. If the BPID-02 card is not installed, the following error message is displayed:

0/1/CPU0 slot counts 'current' ...Response error: 'ENVMON' detected the 'warning' condition 'Hardware not available'

Task ID

Task ID Operation

sysmgr

execute

Examples

The following example illustrates how to use the clear plugin slot counts command:

RP/0/RSP0/CPU0:router(admin)# clear plugin slot counts location 0/FT1/SP

Fri Jan 15 10:15:55.388 pst

 0/FT1/SP slot counts 'current' ... cleared
RP/0/RSP0/CPU0:router(admin)# show plugin slot counts location 0/FT1/SP

Fri Jan 15 10:16:15.503 pst

Backplane connector slot plugin counters

                        Current         Cumulative
0/FT1/SP                0               14

Related Commands

Command

Description

show plugin slot counts

Displays cumulative and running counts of card insertions per slot.

show canbus

Displays the statistics regarding the CAN bus.

crs8 set min-power-modules

To configure the minimum number of modular power entry modules (PEMs) on the 8-slot line card chassis, use the crs8 set min-power-modules command in administration configuration mode. To remove the configuration and revert to the default, use the no form of this command.

crs8 set min-power-modules number

no crs8 set min-power-modules number

Syntax Description

number

Minimum number of power modules for the chassis. Values can be from 0 to 4.

Command Default

Four DC power modules or three AC power modules

Command Modes

Administration configuration

Command History

Release Modification

Release 4.0.1

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the crs8 set min-power-modules command to configure the number of modular PEMs to be used if you are using less than the default number. If you do not use this command and you install less then the default number of PEMs, you receive alarm messages.

Task ID

Task ID Operation

system

read, write

Examples

This example shows how to set the minimum number of modular power modules to three:

RP/0/RP0/CPU0:router(admin-config)# crs8 set min-power-modules 3
  

crs16 set min-power-modules

To configure the minimum number of modular power entry modules (PEMs) on the 16-slot line card chassis, use the crs16 set min-power-modules command in administration configuration mode. To remove the configuration and revert to the default, use the no form of this command.

crs16 set min-power-modules number location node-id

no crs16 set min-power-modules number location node-id

Syntax Description

number

Minimum number of power modules for the chassis. Values can be from 0 to 8.

location node-id

Location of an alarm module for which to specify the number of power modules. The node-id is expressed in the notation rack/slot/*

Note   

Enter the show platform command to see the location of alarm nodes installed in the router.

Command Default

Six DC power modules or five AC power modules

Command Modes

Administration configuration

Command History

Release Modification

Release 4.0.1

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the crs16 set min-power-modules command to configure the number of modular PEMs to be used if you are using less than the default number. If you do not use this command and you install less then the default number of PEMs, you receive alarm messages.

Task ID

Task ID Operation

system

read, write

Examples

This example shows how to set the minimum number of modular power modules to six:

RP/0/RP0/CPU0:router(admin-config)# crs16 set min-power-modules 6 location 0/AM0/SP

dsc serial

To define the serial ID for a rack, use the dsc serial command in administration configuration mode. To remove a serial ID entry from the designated shelf controller (DSC) table, use the no form of this command.

dsc serial serial_id rack rack_num

no dsc serial serial_id rack rack_num

Syntax Description

serial_id

Serial ID for a rack. The serial ID is included as an entry in the DSC table. Range is from 0 through 16 characters.

rack rack_num

Identifies the rack whose ID you are configuring to be the serial ID .

Note   

For systems that include two line card chassis and one fabric chassis, the line card chassis IDs are 0 and 1, and the fabric chassis ID is F0.

Command Default

No default behavior or values

Command Modes

Administration configuration

Command History

Release

Modification

Release 2.0

This command was introduced.

Release 3.2

This command was introduced.

Release 3.3.0

The task ID was updated to system.

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

For more information about identifying and selecting a DSC on your router, see Cisco IOS XR Getting Started Guide for the Cisco XR 12000 Series RouterCisco IOS XR Getting Started Guide for the Cisco CRS RouterCisco ASR 9000 Series Aggregation Services Router Getting Started Guide.


Note


The serial ID is the hardware serial number that identifies the chassis.


Use the show running-config command to display and verify the defined serial ID for a rack.

Task ID

Task ID

Operations

system

read, write

Examples

The following example shows how to define the serial ID for a rack:

RP/0/0RP0RSP0/CPU0:router# admin
RP/0/0RP0RSP0/CPU0:router(admin)# configure
RP/0/0RP0RSP0/CPU0:router(admin-config)# dsc serial TBC0610991700000 rack 1
         

Related Commands

Command

Description

show dsc

Displays the current designated shelf controller (DSC) configuration for the shelf or for the system.

show running-config

Displays the current running (active) configuration.

env disable

To disable environment monitoring on the chassis, use the env disable command in administration configuration mode. To reenable environment monitoring after it has been disabled, use the no form of this command.

env disable

no env disable

Syntax Description

This command has no keywords or arguments.

Command Default

Environment monitoring is enabled.

Command Modes

Administration configuration

Command History

Release

Modification

Release 2.0

This command was introduced.

Release 3.2

The env disable command was moved from the root-system task ID to the system task ID.

Release 3.2

This command was introduced.

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

By default, environment monitoring related to temperature and voltage is enabled on a router running Cisco IOS XR software. If environmental monitoring is disabled, you are not alerted if the router overheats.

Task ID

Task ID

Operations

system

read, write

Examples

The following example shows how to disable environment monitoring with the env disable command:

RP/0/0RP0RSP0/CPU0:router# admin
RP/0/0RP0RSP0/CPU0:router(admin)# configure
RP/0/0RP0RSP0/CPU0:router(admin-config)# env disable
                         

Related Commands

Command

Description

env power-supply disable

Disables power supply monitoring on the chassis.

env power-supply disable

To disable power supply monitoring on the chassis, use the env power-supply disable command in administration configuration mode. To disable power supply monitoring, use the no form of this command.

env power-supply disable

no env power-supply disable

Syntax Description

This command has no keywords or arguments.

Command Default

Power supply monitoring is enabled.

Command Modes

Administration configuration

Command History

Release

Modification

Release 2.0

This command was introduced.

Release 3.3.0

The env power-supply command was moved from the root-system task ID to the system task ID.

The threshold {restart voltage | shutdown voltage} keywords and arguments were added to the env power-supply command.

Release 3.4.1

The threshold {restart voltage | shutdown voltage} keywords and arguments were removed, and the command was changed to env power-supply disable.

Power supply monitoring was enabled by default.

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

system

read, write

Examples

The following example shows how to disable power supply monitoring with the env power-supply disable command:

RP/0/0RP0RSP0/CPU0:router# admin
RP/0/0RP0RSP0/CPU0:router(admin)# configure
RP/0/0RP0RSP0/CPU0:router(admin-config)# env power-supply disable
                   

Related Commands

Command

Description

env disable

Disables environment monitoring on the chassis.

environment altitude

To specify the chassis altitude, so the system can adjust the fan speed to compensate for lower cooling capability at higher altitudes, use the environment altitude command in administration configuration mode. To remove the altitude setting, use the no form of this command.

environment altitude altitude rack rack-no

no environment altitude altitude rack rack-no

Syntax Description

altitude

Chassis location altitude in meters. Values can range from 0 to 4000.

rack rack-no

Specifies the rack number of the chassis.

Command Default

1800 meters

Command Modes

Administration configuration

Command History

Release Modification

Release 4.2.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation

root-system

read, write

Examples

This example specifies that the chassis is located at sea level:

RP/0/0RP0RSP0/CPU0:router(admin-config)#environment altitude 0 rack 0

facility-alarm contacts

To set or unset facilities for processing alarms related to temperature and power supply conditions, use the facility-alarm contacts command in administration EXEC mode.

facility-alarm contacts { all | critical | major | minor } { audio | both | visual } { on | off }

Syntax Description

all

Sets the facility alarm contacts so that an audio and visual alarm alerts the user to a facility alarm of any severity.

critical

Sets the facility alarm contacts so that an audio and visual alarm alerts the user to critical facility alarms.

major

Sets the facility alarm contacts so that an audio and visual alarm alerts the user to major facility alarms.

minor

Sets the facility alarm contacts so that an audio and visual alarm alerts the user to minor facility alarms.

audio

Sets the facility alarm contacts so that an audio alarm alerts the user to alarms of the specified severity.

both

Sets the facility alarm contacts so that an audio and visual alarm alerts the user to alarms of the specified severity.

visual

Sets the facility alarm contacts so that a visual alarm alerts the user to alarms of the specified severity.

on

Enables facility alarm contacts configuration.

off

Disables facility alarm contacts configuration.

Command Default

No default behavior or values

Command Modes

Administration EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

root-system

read

Examples

The following example shows how to enable an audio alarm to alert the user when a critical facility-alarm occurs:

RP/0/0RP0RSP0/CPU0:router# admin
RP/0/0RP0RSP0/CPU0:router(admin)# configure
RP/0/0RP0RSP0/CPU0:router(admin-config)# facility-alarm contacts critical audio on
                     

Related Commands

Command

Description

show fpd package

Displays which SPAs and SIPs are supported with your current Cisco IOS XR software release, which FPD image you need for each card, and what the minimum hardware requirements are for the various modules.

fpd auto-upgrade

To enable the automatic upgrade of FPD images during a software upgrade, use the fpd auto-upgrade command in

administration configuration

System Admin Config

mode. To disable automatic FPD upgrades, use the no form of this command.

fpd auto-upgrade

Syntax Description

This command has no keywords or arguments.

Command Default

FPD images are not automatically upgraded.

Command Modes

Administration configuration

System Admin Config

Command History

Release Modification
Release 4.0.1

This command was introduced.

Release 5.0.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

By default automatic upgrades of the FPD images are not performed during a software upgrade. Once the fpd auto-upgrade command is enabled, when you upgrade the software and an FPD upgrade is required, the FPD upgrade is done automatically before the router is rebooted. The automatic FPD upgrade works only if the FPD image is upgraded together with the mini installation PIE. For example, use the install add and install activate commands as shown here:

(admin)# install add comp-hfr-mini.pie hfr-fpd.pie hfr-mpls-p.pie
(admin)# install activate disk0:/comp-hfr-mini.pie disk0:/hfr-fpd.piedisk0: hfr-mpls-p.pie
  

Task ID

Task ID Operation
system

read, write

Examples

The following example shows how to enable automatic FPD upgrades:

RP/0/0RP0RSP0/CPU0:router(admin-config)# fpd auto-upgrade 

Related Commands

Command

Description

upgrade hw-module fpd

Manually upgrades the current field-programmable device (FPD) image package on a module.

install add

Adds the contents of a PIE file an ISO image, package, and SMUs to a storage device the software repository.

hw-module boot override

To place the standby RP into ROM Monitor mode so that you can update the ROMMON software in a single chassis system to a compatible ROM Monitor version, use the hw-module boot override command in administration configuration mode. To remove an RP from ROM Monitor mode, use the no form of this command.

hw-module boot override

no hw-module boot override

Command Default

No default behavior or values

Command Modes

Administration configuration

Command History

Release

Modification

Release 3.3.0

This command was introduced.

Release 3.9.0

This command was deprecated.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.


Note


This command is deprecated as of Cisco IOS XR Release 3.9.0.


Before you can upgrade a single-chassis system from a release of Cisco IOS XR software prior to Release 3.3.0, you need to first upgrade the ROM Monitor software to a compatible version. If you do not perform this upgrade in a single-chassis system, the standby RP fails to boot and an error message appears. To avoid boot failure, you need to use the hw-module boot override command to place the standby RP into ROM Monitor mode, and update the ROMMON software as required.

For ROM Monitor requirements, refer to the Software/Firmware Compatibility Matrix at the following URL:

http:/​/​www.cisco.com/​web/​Cisco_IOS_XR_Software/​index.html

Use the show platform command to view a summary of the nodes in the router, including status information.

Task ID

Task ID

Operations

root-system

read, write

root-lr

read, write

Examples

The following example shows how to boot the standby RP to upgrade its ROMMON software to a more recent ROM Monitor version:

RP/0/0RP0RSP0/CPU0:router# admin
RP/0/0RP0RSP0/CPU0:router(admin)# configure
RP/0/0RP0RSP0/CPU0:router(admin-config)# hw-module boot override
                       

Related Commands

Command

Description

show platform

Displays information and status for each node in the system.

hw-module location

To reload a node or place a node in maintenance mode, use the hw-module location command in EXEC or administration EXEC mode.

EXEC Modehw-module location { node-id { maintenance-mode | reload { path | plim | warm } } | all reload path }

Administration EXEC Modehw-module location { node-id | all } reload [ path | warm ]

Syntax Description

node-id

Node whose hardware attributes you want to configure. The node-id argument is expressed in the rack/slot/module notation.

Note   

Enter the show platform command to see the location of all nodes installed in the router.

all

Indicates that you want to configure the hardware attributes for all nodes installed in the router.

maintenance-mode

Brings the node down and puts the node into maintenance mode.

reload

Resets power-cycle, reloads hardware, or both, on a specific node.

path

TFTP or disk path to the image you want to download onto the specific node or nodes.

plim

Specifies to reload the PLIM if applicable.

warm

Specifies a warm reload of the node.

Defaults

No default behavior or values

Command Modes

EXEC

Administration EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Release 3.4.0

The maintenance-mode keyword was added in EXEC mode.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.


Note


To reset a specific node or all nodes on the router, or to put a node into maintenance mode, use the hw-module location command in EXEC mode

To reset a specific node or all nodes, use the hw-module location command in administration EXEC mode.


Task ID

Task ID

Operations

root-lr

read

sysmgr

execute

Examples

The following example shows how to reset the hardware on all nodes in the router:

RP/0/0/CPU0:router# admin
RP/0/0/CPU0:router(admin)# hw-module location all reload
  
WARNING: This will take the requested node out of service.
Do you wish to continue?[confirm(y/n)]
    

hw-module location

To configure various hardware attributes for a specific node, or for all nodes installed in the router, use the hw-module location command in EXEC or administration EXEC mode.

To reset or shutdown a specific node, or to put a node into maintenance mode, use the hw-module location command in the System Admin EXEC or XR EXEC mode. To configure the hardware module, use the hw-module location command in the XR Config mode.

EXEC Mode hw-module location node-id { maintenance-mode | reload { path | warm } }

Administration EXEC Mode hw-module location node-id reload { path | warm }

System Admin EXEC Mode hw-module location node-id { offline | online | reload [force] | shutdown [force] }

XR EXEC Mode hw-module location node-id reload [ locationspecifier | warm ] [force]

XR Config Mode hw-module location node-id slice slice-number { breakout 10G | framer-mode { ENET | OTN } | shutdown }

Syntax Description

node-id

Node whose hardware attributes you want to configure. The node-id is expressed in the rack/slot/module notation.

Note   

Enter the show platform command to see the location of all nodes installed in the router.

node-id

Node whose hardware attributes you want to configure. The node-id is expressed in the rack/slot/module notation in the System Admin EXEC mode and represented in the rack/slot/module format in the XR EXEC mode.

Note   

Enter the show platform command to see the location of all nodes installed in the router.

maintenance-mode

Brings the node down and puts the node into maintenance mode.

offline

Changes the state of the hardware module to offline to perform diagnostics. When card is set to offline, it is taken out of the network. However, the card is powered on and maintains connectivity so that it can be accessed for diagnostics.

online

Changes the state of the hardware module to online for normal operation of the device.

reload

Resets power-cycle, reloads hardware, or both on a specific node.

path

Specific image you want to download onto the specific node or nodes. Replace path with the TFTP or disk path to the image you want to download.

shutdown

Shuts down a hardware module.

force

Forces shut down or reload and does not wait for an orderly system shut down.

warm

Specifies a warm reload of the node.

locationspecifier

Specifies the location name.

slice slicenumber

Configures the slice hardware module. The slicenumber value ranges from 1 to 4.

breakout

Configures slice in the breakout mode.

10G

Configures slice in 10G breakout mode

framer-mode

Configures framer mode for the slice.

ENET

Configures slice in the Ethernet mode.

OTN

Configures slice in the OTN mode.

warm

Specifies a warm reload of the node.

Command Default

None

Command Modes

EXECXR EXEC

Global ConfigurationXR Config

Admin EXECSystem Admin EXEC

Command History

Release

Modification

Release 3.3.0

This command was introduced.

Release 3.4.0

The maintenance-mode keyword was added in EXEC mode.

Release 3.7.2

This command was introduced.

Release 5.0.0

This command was introduced.

Usage Guidelines

To reset a specific node, or to put a node into maintenance mode, use the hw-module location command in Admin EXEC modeSystem Admin EXEC mode.

The force keyword forces an immediate reload or shutdown of the router without waiting for an orderly system shutdown.


Caution


A forced reload or shutdown can corrupt the file system. Therefore, use the force keyword only when a normal reload or shutdown does not work.

To ensure that the router has recovered from the forced shutdown, perform a normal reload after restarting the router.

To reset a specific node or all nodes, use the hw-module location command in administration EXEC mode.


Note


Before reloading nodes, we recommend using the cfs check command to check the sanity of the configuration file system and attempt to recover from internal inconsistencies. You need to enter the cfs check command on each secure domain router (SDR) that has nodes impacted by the reload.


Task ID

Task ID

Operations

root-lr

execute (in EXEC mode)

sysmgr

execute (in EXEC mode and administration EXEC mode)

Examples

The following example shows how to reset the hardware on a specific node from EXEC mode:
RP/0/0RP0RSP0/CPU0:router # hw-module location 0/1/CPU0 reload
  
The following example shows how to reset the hardware on a specific node from administration EXEC mode:
RP/0/0RP0RSP0/CPU0:router# admin
RP/0/0RP0RSP0/CPU0:router(admin)# hw-module location 0/3/CPU0 reload
       
The following example shows how to change the state of the hardware module to offline to perform diagnostics:
sysadmin-vm:0_RP0#hw-module location 0/3 offline
Take hardware module offline ? [no,yes] yes

hw-module location reload

To reset the power-cycle or reload the hardware for a specific node, or for all nodes installed in the router, use the hw-module location reload command in EXEC or administration EXEC mode.

hw-module location node-id reload { path | warm }

Syntax Description

node-id

Node whose hardware attributes you want to configure. The node-id is expressed in the rack/slot/module notation.

Note   

Enter the show platform command to see the location of all nodes installed in the router.

path

TFTP or disk path to the image you want to download onto the specific node or nodes.

warm

Specifies a warm reload of the node.

Command Default

No default behavior or values

Command Modes

EXEC

Administration EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

To reset a specific node, use the hw-module location reload command in EXEC mode.

To reset a specific node or all nodes, use the hw-module location reload command in administration EXEC mode.


Note


Before reloading nodes, we recommend using the cfs check command to check the sanity of the configuration file system and attempt to recover from internal inconsistencies.


Task ID

Task ID

Operations

root-lr

execute (in EXEC mode)

sysmgr

execute (in EXEC mode and administration EXEC mode)

Examples

This example shows how to reset the hardware on a specific node from EXEC mode:

RP/0/RSP0/CPU0:router # hw-module location 0/1/CPU0 reload
                        

This example shows how to reset the hardware on a specific node from administration EXEC mode:

RP/0/RSP0/CPU0:router# admin
RP/0/RSP0/CPU0:router(admin)# hw-module location 0/3/CPU0 reload
       

This example shows how to reset the hardware on a specific fabric card node:

RP/0/RSP0/CPU0: router (admin) # hw module location 0/fc0/SP reload

Related Commands

Command

Description

cfs check

Performs a check of the Configuration File System (CFS).

hw-module power location

To power on a specified line card, use the hw-module power location command in administration configuration mode.

hw-module power location node-id

Syntax Description

location node-id

Identifies the node to power on. The node-id argument is expressed in the rack/slot/module notation.

Command Default

Power is on for all nodes.

Command Modes

Administration configuration

Command History

Release

Modification

Release 3.3.0

This command was introduced.

Release 3.7.2

This command was introduced.

Release 4.0.0

The override option was removed.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The hw-module power location command is available for line cards only; it is not available for route processor (RP) route switch processor (RSP) cards.

Use the hw-module power disable location command to power off a line card.

Use the show platform command to view a summary of the nodes in the router, including status information.

By default, cards that do not have a power consumption value programmed on the manufacturing EEPROM cannot be powered up or booted. To correct an issue with such cards, that possibly is because of an incorrectly programmed EEPROM, you can use the hw-module power command with the override option.

Task ID

Task ID

Operations

root-system

read, write

root-lr

read, write

Examples

The following example shows how to power on a line card:

RP/0/0RP0RSP0/CPU0:router# admin
RP/0/0RP0RSP0/CPU0:router(admin)# configure
RP/0/0RP0RSP0/CPU0:router(admin-config)# hw-module power location 0/1/0
         

The following example shows how to disable the power-on feature for a line card:

RP/0/0RP0RSP0/CPU0:router# admin
RP/0/0RP0RSP0/CPU0:router(admin)# configure
RP/0/0RP0RSP0/CPU0:router(admin-config)# hw-module power disable location 0/SM3/SP
         

Related Commands

Command

Description

show platform

Displays information and status for each node in the system.

hw-module power disable

To disable the node power-on feature on a specific line card, use the hw-module power disable command in administration configuration mode. To reenable the node power-on feature on a line card, use the no form of this command.

hw-module power disable location node-id

no hw-module power disable location node-id

Syntax Description

location node-id

Identifies the node whose power-on feature you want to disable. The node-id argument is expressed in the rack/slot/module notation.

Command Default

Power is on for all nodes.

Command Modes

Administration configuration

Command History

Release

Modification

Release 3.3.0

This command was introduced.

Release 3.7.2

This command was introduced.

Release 3.9.0

The option to use this command without the disable keyword was removed.

Release 4.0.0

The override keyword was removed.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the show platform command to view a summary of the nodes in the router, including status information.

The hw-module power disable command is available for line cards only; it is not available for RP cards.

Task ID

Task ID

Operations

sysmgr

read, write

root-lr

read, write

Examples

The following example shows how to disable the node power-on feature on a line card:

RP/0/0RP0RSP0/CPU0:router# admin
RP/0/0RP0RSP0/CPU0:router(admin)# configure
RP/0/0RP0RSP0/CPU0:router(admin-config)# hw-module power disable location 0/0/CPU0
         

The following example shows how to disable the node power-on feature on a fabric card:

RP/0/0RP0RSP0/CPU0:router (admin-config) # hw-module power disable location 0/fc0/SP

Related Commands

Command

Description

show platform

Displays information and status for each node in the system.

hw-module profile feature

To enable a feature bundle on the router, use the hw-module profile feature command in administration configuration mode. To disable a feature bundle, use the no form of this command.

hw-module profile feature { default | l2 | imsg }

no hw-module profile feature { default | l2 | imsg }

Syntax Description

default

Feature profile that supports all features except provider backbone bridge (PBB)except iMSG Layer 2 aggregation..

l2

Feature profile that supports PBB, but does not support IPv6, reverse-path forwarding (RPF) and netflow.

imsg

Feature profile that does not support Layer 3 VPN over IP core.

Command Default

The default feature profile is default.

Command Modes

Administration configuration

Command History

Release Modification

Release 4.0.1

This command was introduced.

Release 4.2.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

If you do not configure the feature profile, the default profile is active. The default feature profile does not support provider backbone bridge (PBB). If you need support for PBB, configure the L2 feature profile.

If you do not reload the line cards after configuring the feature profile, the configured profile is not active and this warning message is displayed. You must reload the affected line card so that the configured profile matches the active profile.

LC/0/1/CPU0:Nov 5 02:50:42.732 : prm_server[236]: Configured
'hw-module profile feature l2' does not match active 'hw-module
profile feature default'. You must reload this line card in order
to activate the configured profile on this card or you must change
the configured profile.
  

If you have configured features that are not supported in your active feature profile, this warning is displayed. You should either change the feature profile configuration, or remove the non-supported features.

LC/0/1/CPU0:Nov 5 02:50:42.732 : prm_server[236]: Active 'hw-module
profile feature l2' does not support IPv6, RPF, or Netflow
features. Please remove all unsupported feature configurations.
        

If you do not configure the feature profile, the default profile is active. The default profile does not support iMSG Layer 2 aggregation. If you need to configure iMSG Layer 2 aggregation, use the iMSG profile.


Note


When you change the profile, all Modular Multirate IP Services Engine cards in the router are reloaded.


Any configurations that existed before you change the profile that are not supported by the new profile, are disabled. You should manually remove all such configurations.

If you attempt to remove an existing feature profile configuration by using the no form of this command, this warning message is displayed and no action is taken. In other words, the configuration is not removed from the running configuration.

This is an invalid operation. Use 'hw-module profile feature 
default' to revert to a base configuration.
  

Task ID

Task ID Operation

system

read, write

root-lr

read, write

Examples

This example shows how to set the feature profile to L2:

RP/0/RSP0/CPU0:router# admin
RP/0/RSP0/CPU0:router(admin)# configure
RP/0/RSP0/CPU0:router(admin-config)# hw-module profile 
feature l2

Wed Dec  8 08:29:54.053 PST
L2 feature profile does NOT support the following features: 
IPv6, RPF, Netflow.
In order to activate this new memory resource profile,
you must manually reboot the line cards.
RP/0/RSP0/CPU0:router(admin-config)# commit
  

Examples

This example shows how to set the feature profile to iMSG:

RP/0/0RP0RSP0/CPU0:router(admin-config)# hw-module profile feature imsg 

Thu Sep  8 22:17:39.739 DST
iMSG feature profile does NOT support the following features: Biscuit. 
Upon commit, all E5 LCs will be reloaded

Related Commands

Command

Description

show hw-module profile

Displays the active profiles.

hw-module profile scale

To specify a scale profile for the router, use the hw-module profile scale command in administration configuration mode.

hw-module profile scale { default | l3 | l3xl }

Syntax Description

default

Scale profile applicable for deployments that require large Layer 2 MAC tables (up to 512,000 entries) and a relatively small number of Layer 3 routes (less than 512,000).

l3

Scale profile applicable for deployments that require more Layer 3 routes (up to 1 million) and smaller Layer 2 MAC tables (less than 128,000 entries).

l3xl

Scale profile applicable for deployments that require a very large number of Layer 3 routes (up to 1.3 million) and minimal Layer 2 functionality.

Command Default

default is the default scale profile

Command Modes

Administration configuration

Command History

Release Modification

Release 3.9.1

This command was introduced.

Release 4.0.1

The l3xl keyword was introduced.

This command was moved to administration configuration mode.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the hw-module profile scale command to configure the router to perform more efficiently depending on the use of the router.

  • Specify the scale profile to be default in situations where the router is used as a Layer 2 transport device that requires the router to support high Layer 2 scale numbers.

  • Specify the scale profile to be l3xl in situations where the router is used primarily as a Layer 3 box to provide Layer 3 VPN services. In this case, the router needs to support a high number of Layer 3 routes.


Note


When you upgrade to a release that supports the hw-module profile scale command in adminstration configuration mode, the non-administration configured settings are retained and used. Once you configure the scale profile in the administration plane, it has higher priority than the non-administration plane, and it replaces the non-administration scale profile configuration.


Task ID

Task ID Operation

system

read, write

root-lr

read, write

Examples

The following example shows how to set the scale profile to Layer 3:

RP/0/RSP0/CPU0:router# admin
RP/0/RSP0/CPU0:router(admin)# configure
RP/0/RSP0/CPU0:router(admin-config)# hw-module profile 
scale l3

Tue Aug 24 23:52:51.828 UTC
In order to activate this new memory resource profile, 
you must manually reboot the system.
RP/0/RSP0/CPU0:router(admin-config)# commit
  

Related Commands

Command

Description

show hw-module profile

Displays the active profiles.

hw-module reset auto

To reset a specific node, use the hw-module reset auto command in administration configuration mode. To disable the reset feature on a specific node, use the no form of this command.

hw-module reset auto [disable] location node-id

no hw-module reset auto [disable] location node-id

Syntax Description

disable

Disables the node reset feature on the specified node.

location node-id

Identifies the node you want to reload. The node-id argument is entered in the rack/slot/module notation.

Command Default

The node reset feature is enabled for all nodes.

Command Modes

Administration configuration

Command History

Release

Modification

Release 3.3.0

This command was introduced.

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The hw-module reset auto command is used to reload Cisco IOS XR software on a specific node. The node reloads with the current running configuration and active software set for that node.

Task ID

Task ID

Operations

root-system

read, write

root-lr

read, write

Examples

The following example shows how to reload a node:
RP/0/0RP0RSP0/CPU0:router# admin
RP/0/0RP0RSP0/CPU0:router(admin)# configure
RP/0/0RP0RSP0/CPU0:router(admin-config)# hw-module reset auto location 0/2/CPU0
  
RP/0/RP0/CPU0:router# RP/0/RP0/CPU0:Apr  2 22:04:43.659 : shelfmgr[294]: 
%S HELFMGR-3-USER_RESET : Node 0/2/CPU0 is reset due to user reload request
  

hw-module reset auto disable

To disable the node reset feature on a specific node, use the hw-module reset auto disable command in administration configuration System Admin Config mode. To reenable the reset feature on a specific node, use the no form of this command.

hw-module reset auto disable location node-id

no hw-module reset auto disable location node-id

Syntax Description

location node-id

Identifies the node on which you want to disable the auto reset feature in case of errors. The node-id argument is entered in the rack/slot/module notation.

Command Default

The node reset feature is enabled for all nodes.

The node reset feature is disabled for all nodes.

Command Modes

Administration configuration

System Admin Config

Command History

Release

Modification

Release 3.3.0

This command was introduced.

Release 3.7.2

This command was introduced.

Release 5.0.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

sysmgr

read, write

root-lr

read, write

Examples

This example shows how to disable the reset feature on a node:
RP/0/0RP0RSP0/CPU0:router# admin
RP/0/0RP0RSP0/CPU0:router(admin)# configure
RP/0/0RP0RSP0/CPU0:router(admin-config)# hw-module reset auto disable location 0/0/CPU0
         
 
sysadmin-vm:0_RP0# config
sysadmin-vm:0_RP0(config)# hw-module reset auto disable location 0/1
sysadmin-vm:0_RP0(config-location-0/1)# commit
Tue Aug  27 19:47:37.841 UTC
Commit complete.
sysadmin-vm:0_RP0(config-location-0/3)# exit
Tue Aug  27 19:47:37.841 UTC
sysadmin-vm:0_RP0(config)# exit

                                             

Related Commands

Command

Description

hw-module power location

Powers on a specified line card.

hw-module power disable

Disables the node power-on feature on a specific line card.

hw-module service maintenance-mode location

To configure the router to take a specific node into maintenance mode in the event of disaster recovery, use the hw-module service maintenance-mode location command in global configuration mode. To reset this configuration, use the no form of the command.

hw-module service maintenance-mode location node-id

no hw-module service maintenance-mode location node-id

Syntax Description

node-id

Location of the service card that you want to move into offline mode. The node-id argument is entered in the rack/slot/module notation.

Command Default

In case of disaster recovery, the router reloads a failed line card if MDR is unsuccessful, and does not put the line card in maintenance mode.

Command Modes

Global configuration

Command History

Release

Modification

Release 3.4.1

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

In the event that a line card fails, the router attempts to restart all the processes on the line card without disrupting the traffic flow. This is called a Minimum Disruptive Restart (MDR). If the MDR does not recover the line card, the router reloads the line card. You can configure the router to place the line card into maintenance mode after an unsuccessful MDR, instead of reloading it. Use the hw-module service maintenance-mode location command to configure the router to take a specified line card into maintenance mode after an unsuccessful MDR, instead of reloading the line card.

Maintenance mode is a mode in which only the processes that are required for collecting useful data for debugging run.

Task ID

Task ID

Operations

root-lr

read, write

Examples

The following example shows how to move the card at 0/1/CPU0 into maintenance mode:

RP/0/0RP0RSP0/CPU0:router# configure               
RP/0/0RP0RSP0/CPU0:router(config)# hw-module service maintenance-mode location 0/1/CPU0            
                     

Related Commands

Command

Description

hw-module location

Reloads a node or places a node in maintenance mode.

hw-module location

Configures various hardware attributes for a specific node, or for all nodes installed in the router.

show services role

Displays the current service role on service cards installed in your router.

hw-module service offline location

To configure offline mode as the role for a specific node, use the hw-module service offline location command in

global configuration

XR Config

mode. To disable offline mode, use the no form of the command.

hw-module service offline location node-id

no hw-module service offline location node-id

Syntax Description

node-id

Location of the service card that you want to move into offline mode. The node-id argument is entered in the rack/slot/module notation.

Command Default

No default behavior or values

Command Modes

Global configuration

XR Config

Command History

Release

Modification

Release 3.4.0

This command was introduced.

Release 5.0.0

This command was introduced.

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Offline mode disables all configured service instances on a service card. If there is a service active on the service card, the service switches over to a standby location if a standby is configured.

Task ID

Task ID

Operations

root-lr

read, write

Examples

The following example shows how to move the card at 0/1/CPU0 into offline mode:

RP/0/0RP0RSP0/CPU0:router# configure              
RP/0/0RP0RSP0/CPU0:router(config)# hw-module service offline location 0/1/CPU0           
               

Related Commands

Command

Description

show services role

Displays the current service role on service cards installed in your router.

hw-module shutdown


Note


Effective with Cisco IOS XR Release 3.9.0, the hw-module shutdown command is not supported.


To administratively shut down a specific node, use the hw-module shutdown command in Admin Configuration modeSystem Admin Config mode. To return a node to the up state, use the no form of this command.

hw-module shutdown location node-id

no hw-module shutdown location node-id

Syntax Description

location node-id

Identifies the node you want to shut down. The node-id argument is expressed in the rack/slot/module notation.

Command Default

Nodes are in the up state.

Nodes are in the up state when the system is powered on and when the software boots on the cards.

Command Modes

Admin ConfigurationSystem Admin Config

Command History

Release

Modification

Release 2.0

This command was introduced.

Release 3.2

This command was modified from the hw-module node shutdown command. The node keyword was replaced by the location keyword, which was moved to the end of the command string.

Release 3.2

This command was introduced.

Release 3.7.2

This command was introduced.

Release 3.9.0

This command was removed.

Release 5.0.0

This command was introduced.

Usage Guidelines

Nodes that are shut down still have power, but cannot load or operate Cisco IOS XR software.

Nodes that are shut down do not have power.


Note


Route processors (RPs) cannot be administratively shut down.


Route processors (RPs), Fan tray (FT), and Power tray (PT) cannot be shutdown using the hw-module shutdown command.

Enter the show platform command in Admin EXEC modeSystem Admin EXEC mode to display the results of the hw-module shutdown command.

Task ID

Task ID

Operations

root-system

read, write

sysmgr

read, write

root-lr

read, write

Examples

The following example shows how to administratively shut down the node 0/2/CPU0:
RP/0/0RP0RSP0/CPU0:router# admin
RP/0/0RP0RSP0/CPU0:router(admin)# configure
RP/0/0RP0RSP0/CPU0:router(admin-config)# hw-module shutdown location 0/2/CPU0
         
The following example shows how to bring up a node using the no form of the hw-module shutdown command:
RP/0/0RP0RSP0/CPU0:router# admin
RP/0/0RP0RSP0/CPU0:router(admin)# configure
RP/0/0RP0RSP0/CPU0:router(admin-config)# no hw-module shutdown location 0/2/CPU0
         
This example shows how to shutdown the node 0/1 and view the result using the show platform command:
 
sysadmin-vm:0_RP0#config
Tue Aug  27 12:47:40.391 UTC
Entering configuration mode terminal
sysadmin-vm:0_RP0# hw-module shutdown location 0/1
sysadmin-vm:0_RP0(config-location-0/1)# commit
Tue Aug  27 12:47:57.307 UTC
Commit complete.
sysadmin-vm:0_RP0(config-location-0/1)# exit
Tue Aug  27 12:48:00.171 UTC
sysadmin-vm:0_RP0(config)# exit
Tue Aug  27 12:48:02.619 UTC
sysadmin-vm:0_RP0# show platform location 0/1
Tue Aug  27 12:48:20.766 UTC
Location  Card Type               HW State      SW State      Config State
----------------------------------------------------------------------------
0/1       NC6-10X100G-M        PRESENT       SW_INACTIVE   SHUT

Related Commands

Command

Description

hw-module power location

Powers on a specified line card.

hw-module power disable

Disables the node power-on feature on a specific line card.

hw-module reset auto

Resets a specific node.

hw-module reset auto disable

Disables the node reset feature on a specific node.

hw-module subslot reload

To reload Cisco IOS XR software on a specific subslot, use the hw-module subslot reload command in EXEC mode.

hw-module subslot subslot-id reload

Syntax Description

subslot-id

Specifies the subslot to be restarted. The subslot-id argument is entered in the rack/slot/subslot notation.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Release 3.9.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

This command reloads Cisco IOS XR software on the specified shared port adapter (SPA) and restarts the SPA interfaces. The SPA reloads with the current running configuration and active software set for the SPA.

Task ID

Task ID

Operations

root-lr

read, write

Examples

The following example shows how to restart the SPA in slot 2, subslot 1:

RP/0/0RP0RSP0/CPU0:router# hw-module subslot 0/2/1 reload
        

Related Commands

Command

Description

hw-module subslot shutdown

Administratively shuts down a specific shared port adapter.

hw-module subslot shutdown

To administratively shut down a specific shared port adapter (SPA), use the hw-module subslot shutdown command in

global configuration

XR Config

mode. To return a SPA to the up state, use the no form of this command.

hw-module subslot subslot-id shutdown [ powered | unpowered ]

no hw-module subslot subslot-id shutdown

Syntax Description

subslot-id

Specifies the subslot to be shut down. The subslot-id argument is entered in the rack/slot/subslot notation.

powered

(Optional) Retains power to the specified subslot.

unpowered

(Optional) Powers down completely the specified subslot.

Command Default

Shutdown is powered if no option is specified.

Command Modes

Global configuration

XR Config

Command History

Release

Modification

Release 3.2

This command was introduced.

Release 3.9.0

This command was introduced.

Release 5.0.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

This command administratively shuts down the SPA in the specified subslot. Subslots that are shut down still have power but cannot load or operate Cisco IOS XR software.

Task ID

Task ID

Operations

root-lr

read, write

Examples

The following example shows how to shut down the SPA in subslot 1 of the SPA interface processor (SIP) in slot 2:

RP/0/0RP0RSP0/CPU0:router# configure
RP/0/0RP0RSP0/CPU0:router(config)# hw-module subslot 0/2/1 shutdown powered
       

Related Commands

Command

Description

shutdown (global)

Disables an interface (forces an interface to be administratively down).

led mode

To change the message, mode or status of a router card LED display, use the led mode command in administration configuration mode. To revert to the default message, mode or status, use the no form of this command.

led mode { blink | default | scroll } { lock | unlock } message location node-id

Syntax Description

{blink | default | scroll}

Specifies the mode of the card LED display.

{lock | unlock}

Specifies the status of the card LED display.

message

Specifies the message to display on the card LED.

location node-id

Specifies the node for which to configure the LED information. The node-id argument is expressed in the rack/slot/module notation.

Command Default

Mode: default; status: unlocked; message: according to the state of the software

Command Modes

Administration configuration

Command History

Release Modification

Release 3.8.0

This command was introduced.

Usage Guidelines

You must be in a user group associated with a task group that includes the proper task IDs. The command reference guides include the task IDs required for each command. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the show led command to display the LED settings for a card or all cards.

Task ID

Task ID Operation

system

read, write

Examples

This example shows how to change the message displayed on the card LED and the subsequent display in the show led command output:

RP/0/0RP0RSP0/CPU0:router# admin
RP/0/0RP0RSP0/CPU0:router(admin)# configure
RP/0/0RP0RSP0/CPU0:router(admin-config)# led mode default unlock STBY_RP location 0/rp0/cpu0
RP/0/0RP0RSP0/CPU0:router(admin-config)# end

Uncommitted changes found, commit them? [yes]: 
RP/0/0RP0RSP0/CPU0:router(admin)# show led location all | i 0/RP0/CPU0

     LOCATION        MESSAGE        MODE      STATUS 
    ==================================================
        0/0/SP       IOX-RUN       DEFAULT   UNLOCKED
        0/1/SP       IOX-RUN       DEFAULT   UNLOCKED
    0/RP0/CPU0        STBY_RP      DEFAULT   UNLOCKED 
    0/RP1/CPU0       ACTV RP       DEFAULT   UNLOCKED
  

Related Commands

Command

Description

show led

Displays LED information for the router, or for a specific LED location.

power budget enforcement disable

To disable the power budget calculation and allow line cards to boot in an over-budget condition, use the power budget enforcement disable command in administration configuration mode. To enable the power budget calculation once again, use the no form of this command.

power budget enforcement disable

no power budget enforcement disable

Syntax Description

This command has no keywords or arguments.

Command Default

Power budget is enforced.

Command Modes

Administration configuration

Command History

Release Modification
Release 4.0.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The power manager automatically reads the required power supply values from the EEPROM on all cards and calculates the required power budget. The system can power up line cards only if there is sufficient power. Use the power budget enforcement disable command to disable the power budget calculation and to allow the system to boot cards in an over-budget condition.

Use the show environment command with the power option to display the current power current and draw.

If the system is running with a power budget deficiency and the power budget enforcement disable command is not configured, a reset of a line card powers down the line card. Beginning with Cisco IOS XR Release 4.3.1, if you configure the power budget enforcement disable command, behavior is normal even if the system has a power budget deficiency.

Task ID

Task ID Operation

root-system

read, write

Examples

The following example shows how to disable the power management calcuations:

RP/0/RSP0/CPU0:router# admin
RP/0/RSP0/CPU0:router(admin)# config
RP/0/RSP0/CPU0:router(admin-config)# power budget enforcement disable
  

Related Commands

Command

Description

show environment

Displays environmental monitor parameters for the system.  

power budget reservation

To release the standby route switch processor (RSP) power budget reservation, use the power budget reservation command in administration configuration mode. To re-reserve the standby RSP power budget reservation, use the no form of this command.

power budget reservation standby-rsp disable

no power budget reservation standby-rsp disable

Syntax Description

standby-rsp disable

Disables the power budget reservation for the standby RSP.

Command Default

Power is reserved for the standby RSP.

Command Modes

Administration configuration

Command History

Release Modification
Release 4.0.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the power budget reservation command to disable the power budget reservation for the standby RSP if you only have one RSP installed in the router and you need additional power for other cards. Use the show environment command with the power-supply keyword to view the available power budget on the system.

Task ID

Task ID Operation

root-system

read, write

Examples

The following example shows how to disable the power budget for the standby RSP:

RP/0/RSP1/CPU0:router(admin-config)# power budget reservation standby-rsp disable
  

Related Commands

Command

Description

show environment

Displays environmental monitor parameters for the system.  

redundancy switchover

To cause the primary (active) route processor (RP) to fail over to the redundant standby RP, use the redundancy switchover command in

EXEC or administration EXEC

XR EXEC

mode. To disable the forced switchover, use the no form of this command.

redundancy switchover [ location node-id ]

no redundancy switchover [ location node-id ]

Syntax Description

location node-id

(Optional) Specifies the primary RP on which to force a switchover. The node-id argument is expressed in the rack/slot/module notation.

Command Default

No default behavior or values

Command Modes

EXEC

Administration EXEC

XR EXEC

Command History

Release

Modification

Release 2.0

This command was introduced.

Release 5.0.0

This command was introduced.

Release 3.3.0

The redundancy switchover command was moved from the system task ID to the root-lr task ID.

Release 3.3.0

This command was introduced.

Release 3.5.0

This command was supported in administration EXEC mode.

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the redundancy switchover command to trigger a switchover from the primary RP to the standby RP. When the redundancy switchover command is issued, the running (committed) configuration is automatically saved and loaded during switchover, and the standby RP becomes the active primary RP, while the original primary RP becomes the standby RP.


Note


The redundancy switchover command can be used only if the standby RP is in the ready state. Use the show redundancy command to view the status of the RPs.


Task ID

Task ID

Operations

root-lr

read, write

Examples

The following example shows partial output for a successful redundancy switchover operation:

RP/0/0RP0RSP0/CPU0:router# show redundancy
  
  Redundancy information for node 0/RP0/CPU0:
  ==========================================
  Node 0/RP0/CPU0 is in ACTIVE role
  Partner node (0/RP1/CPU0) is in STANDBY role
  Standby node in 0/RP1/CPU0 is ready
  
  Reload and boot info
  ----------------------
  RP reloaded Tue Mar 28 09:02:26 2006: 5 hours, 41 minutes ago
  Active node booted Tue Mar 28 09:02:56 2006: 5 hours, 41 minutes ago
  Last switch-over Tue Mar 28 09:09:26 2006: 5 hours, 34 minutes ago
  Standby node boot Tue Mar 28 09:10:37 2006: 5 hours, 33 minutes ago
  Standby node last went not ready Tue Mar 28 09:25:49 2006: 5 hours, 18 minutes
  go
  Standby node last went ready Tue Mar 28 09:25:51 2006: 5 hours, 18 minutes ago
  There has been 1 switch-over since reload
  ....
RP/0/0RP0RSP0/CPU0:router# redundancy switchover
  
  Initializing DDR SDRAM...found 2048 MB
  Initializing ECC on bank 0
  ...
  Turning off data cache, using DDR for first time
  
  Initializing NVRAM...
  Testing a portion of DDR SDRAM ...done
  Reading ID EEPROMs ...
  Initializing SQUID ...
  Initializing PCI ...
  
  PCI0 device[1]: Vendor ID 0x10ee
  
  Configuring MPPs ...
  Configuring PCMCIA slots ...
  --More--
    

If the standby RP is not in the ready state, the switchover operation is not allowed. The following example shows output for a failed redundancy switchover attempt:

RP/0/0RP0RSP0/CPU0:router# show redundancy
  
  This node (0/RP0/CPU0) is in ACTIVE role
  Partner node (0/RP1/CPU0) is in UNKNOWN role
  
RP/0/0RP0RSP0/CPU0:router# redundancy switchover
  
  Standby card not running; failover disallowed.
  

Related Commands

Command

Description

show redundancy

Displays the status of route processor redundancy.

service-location

To associate a physical location on a service card with a firewall, or VRF-Aware Service Infrastructure (VASI) interface service instance, and, optionally, to configure a standby location for service switchover, use the service-location command in the appropriate service configuration mode. To remove the association, use the no form of this command.

service-location preferred-active node-id [ preferred-standby node-id [auto-revert] ]

no service-location preferred-active node-id [ preferred-standby node-id [auto-revert] ]

Syntax Description

preferred-active node-id

Specifies the physical location of the service card on which you prefer that the service should be active. The node-id argument is entered in the rack/slot/module notation.

preferred-standby node-id

Specifies a standby physical location for the service. The node-id argument is entered in the rack/slot/module notation.

auto-revert

Specifies that the service revert to the preferred active firewall when the active node comes back up after a switchover.

Note   

Do not use auto-revert with more than 100 contexts in your configuration.

Command Default

No default behavior or values

Command Modes

Firewall configuration

VASI interface configuration

Command History

Release

Modification

Release 3.5.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the service-location command to specify the location of the service card to handle a VASI virtual interface. The service-location command can be configured on either of the interface halves, but if it is configured on both, the locations given must match exactly. If the service-location command is not configured, both halves of the pair remain down.

Task ID

Operations

firewall

read, write

Examples

The following example shows how to create a firewall named “fw1” in Cisco IOS XR software and associate it with the physical location at 0/0/cpu0:

RP/0/0/CPU0:router# configure               
RP/0/0/CPU0:router(config)# firewall fw1            
RP/0/0/CPU0:router(config-firewall)# service-location preferred-active 0/0/CPU0 preferred-standby 0/1/CPU0 auto-revert  
         

The following example shows how to use the service-location command to enable a VASI interface:

RP/0/0/CPU0:router# configure               
RP/0/0/CPU0:router(config)# interface vasileft 1            
RP/0/0/CPU0:router(config-if)# vrf red  
RP/0/0/CPU0:router(config-if)# ipv4 address 10.1.2.171 255.255.255.0
RP/0/0/CPU0:router(config-if)# service-location preferred-active 0/0/CPU0 preferred-standby 0/1/CPU0 auto-revert               
         

Related Commands

Command

Description

default-interface-name

Configures the default interface that represents any unprotected interface in the router.

failure-action

Configures the action to take if a failure or misconfiguration occurs.

firewall

Configures a virtual firewall in Cisco IOS XR software.

firewall (interface)

Configures the firewall attachment.

interface vasi

Configures a VASI interface and enters interface configuration mode.

show services role

Displays the configured roles of the service cards.

show services redundancy

Displays all configured services and their active and standby physical locations.


Related Commands

Command

Description

show services role

Displays the current service role on service cards installed in your router.

show services redundancy

show canbus

To display statistics regarding the CAN bus, use the show canbus command in administration EXEC mode.

show canbus { client-stats | controller-stats | server-stats } location { all | node-id }

Syntax Description

client-stats

Displays CAN bus client statistics.

controller-stats

Displays CAN bus controller statistics.

server-stats

Displays CAN bus server statistics.

location {all | node-id}

Displays the status of the CAN bus for a specific node or all nodes.

Command Default

None

Command Modes

Administration EXEC

Command History

Release Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the show canbus command with the server-stats keyword to determine if the revised backplane ID board (BPID-02) is installed in the router.

Task ID

Task ID Operation

sysmgr

read

Examples

The following example illustrates sample output from the show canbus command with the server-stats keyword:

RP/0/RSP0/CPU0:router(admin)# show canbus server-stats location all

       Slot   State Partition-A Rev Partition-B Rev Active-Partition
   0/0/CPU0  Online            2.01            2.02      Partition B
   0/1/CPU0  Online            2.01            2.02      Partition B
   0/2/CPU0 Offline --------------- --------------- ----------------
   0/3/CPU0 Offline --------------- --------------- ----------------
0/RSP0/CPU0  Online            1.01            1.02      Partition B
0/RSP1/CPU0  Online            1.01            1.02      Partition B
   … snip …
   0/FT0/SP  Online            4.00            4.00      Partition A
   0/FT1/SP  Online            4.00            4.00      Partition B
 0/BPID0/SP  Online            7.00            7.00      Partition B     
  

Related Commands

Command

Description

clear plugin slot counts

Clears the running counts of the backplane connector slot plugins.  

show plugin slot counts

Displays cumulative and running counts of card insertions per slot.  

show dsc

To display the current designated shelf controller (DSC) configuration for the shelf or for the system, enter the show dsc command in administration EXEC mode.

show dsc [ all | mine | location node-id ]

Syntax Description

all

Displays DSC information from all available nodes in the system.

mine

Displays information about the current node.

location node-id

Displays DSC information for a specific node. The node-id is expressed in the rack/slot/module notation.

Command Default

This command has no keywords or arguments.

Command Default

No default behavior or values

Command Modes

Administration EXEC

Command History

Release

Modification

Release 2.0

This command was introduced.

Release 3.2

This command was introduced.

Release 3.3.0

The node keyword was replaced by the location keyword.

The show dsc command was moved from the root-system task ID to the system task ID.

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

For more information about identifying and selecting a DSC on your router, see Cisco IOS XR Getting Started Guide for the Cisco XR 12000 Series RouterCisco IOS XR Getting Started Guide for the Cisco CRS RouterCisco ASR 9000 Series Aggregation Services Router Getting Started Guide.

Task ID

Task ID

Operations

system

read

Examples

The following example shows sample output from the show dsc command with the mine keyword.


RP/0/0/CPU0:router# admin
RP/0/0/CPU0:router(admin)# show dsc mine
  
  NODE           ROLE        PRIORITY      TBEACON   PRESENT  MIGRATION
  =====================================================================
  0/0/CPU0       DSC         3             2000      YES      ENABLED
  ---------------------------------------------------------------------
    

RP/0/RP0/CPU0:router# admin
RP/0/RP0/CPU0:router(admin)# show dsc mine
Sun Jan 25 04:26:33.103 PST

NODE           ROLE        PRIORITY      TBEACON   PRESENT  SERIAL ID

============================================================================
0/RP0/CPU0     DSC         DEFAULT       300       YES      TBA09160TBA
----------------------------------------------------------------------------
  
Table 1  show dsc Field Descriptions

Field

Description

NODE

Location of the node in the rack/slot/module notation.

ROLE

Role this node is performing.

PRIORITY

DSC priority assigned to this node.

TBEACON

Current DSC beacon timeout value.

PRESENT

Indicates whether the node is present in the slot.

SERIAL ID

Serial ID assigned to this node.

MIGRATION

Displays the current DSC migration functionality to the standby card. Can be one of the following:

  • ENABLE—Migration process is enabled

  • UNKNOWN—Migration configuration is unknown.

The following example shows sample output from the show dsc command with the all keyword:


RP/0/0/CPU0:router# admin
RP/0/0/CPU0:router(admin)# show dsc all
  
  NODE           ROLE        PRIORITY      TBEACON   PRESENT  MIGRATION
  =====================================================================
  0/0/CPU0       DSC         3             2000      YES      ENABLED
  ---------------------------------------------------------------------
  0/5/CPU0       NON-DSC     5             2000      YES      ENABLED
  ---------------------------------------------------------------------
   

RP/0/RP0/CPU0:router#admin
RP/0/RP0/CPU0:router(admin)#show dsc all

NODE           ROLE        PRIORITY      TBEACON   PRESENT  SERIAL ID

============================================================================
0/RP0/CPU0     DSC         DEFAULT       300       YES      TBA09370035
----------------------------------------------------------------------------
0/RP1/CPU0     BACKUP      DEFAULT       300       YES      TBA09370035
----------------------------------------------------------------------------
0/4/CPU0       NON-DSC     65            300       YES      TBA09370035
----------------------------------------------------------------------------
0/4/CPU1       NON-DSC     66            300       YES      TBA09370035
----------------------------------------------------------------------------
  

RP/0/RSP0/CPU0:PE44_ASR-9010(admin)# show dsc

Thu Jul 30 02:51:59.628 DST
NODE         ROLE
========================
0/RSP0/CPU0  DSC
  

Related Commands

Command

Description

dsc serial

Defines the serial ID for a rack.

show environment

To display environmental monitor parameters for the system, use the show environment command in the appropriate mode.

EXEC Mode: show environment [ all | last | leds | location { all | node-id } | table | temperatures | voltages ] [node-id]

Administration EXEC Mode: show environment [ all | fans | last | leds | location { all | node-id } | power-supply | table | temperatures | trace | voltages ] [node-id]

EXEC Mode: show environment [ all | table | temperatures | voltages ] [last] [node-id]

Administration EXEC Mode: show environment [ all | fans | last | leds | power-supply | table | temperatures | voltages ] [node-id]

SysAdmin EXEC Mode: show environment { all | current | fan | power | temperatures | trace | voltages } location [node-id]

Syntax Description

current

Displays all the current information.

all

(Optional) Displays information for all environmental monitor parameters.

fans

(Optional) Displays information about the fans.

last

(Optional) Displays the environmental statistics at the time of the last shutdown.

leds

(Optional) Displays monitor parameters for LEDs on all cards in the node.

location {all | node-id}

(Optional) Displays all environmental monitor parameters for the specified location only.

power

(Optional) Displays power supply voltage and current information.

table

(Optional) Displays environmental parameter ranges.

temperatures

(Optional) Displays system temperature information.

trace

(Optional) Displays trace data for environment monitoring.

voltages

(Optional) Displays system voltage information.

node-id

(Optional) Node whose information you want to display. The node-id argument is expressed in the rack/slot/module notation.

Command Default

All environmental monitor parameters are displayed.

Command Modes

EXEC

Administration EXEC

System Admin EXEC

Command History

Release

Modification

Release 2.0

This command was introduced.

Release 5.0.0

This command was introduced.

Release 3.2

This command was introduced.

Release 3.3.0

The optional node-id argument was supported.

The show environment command was moved from the root-system task ID to the system task ID.

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The show environment command displays information about the hardware that is installed in the system, including fans, LEDs, power supply voltage, and current information and temperatures.

Task ID

Task ID

Operations

system

read

Examples

The following example shows sample output from the show environment command with the temperatures keyword:

RP/0/0RP0RSP0/CPU0:router # show environemnt temperatures
Location  Sensor                      Value   Crit Major Minor Minor Major  Crit
                                    (deg C)   (Lo) (Lo)  (Lo)  (Hi)  (Hi)   (Hi)
================================================================================
0/5
          MB Inlet                       24    -10    -5     0    50    60    70
          HotSpot                        28    -10    -5     0    95   100   105
          MB Outlet                      24    -10    -5     0    95   100   105
          Sandy Bridge Die               38    -10    -5     0    75    85    95
          PCIe Die                       44    -10    -5     0   105   115   125
          Slice 1 PITA Die Remote        46    -10    -5     0   105   110   115
          Slice 1 AMBA Die local         35    -10    -5     0    95   100   105
          Slice 1 AMBA Die Remote        39    -10    -5     0   105   110   115
0/RP1
          Inlet                          21    -10    -5     0    45    55    65
          HotSpot                        32    -10    -5     0    65    75    85
          Outlet                         32    -10    -5     0    65    75    85
          PCIe Die                       36    -10    -5     0   105   115   125
          Chassis local                  22    -10    -5     0    45    55    65
          Chassis remote                 22    -10    -5     0    45    55    65
          Sandy Bridge                   36    -10    -5     0    75    85    95
0/FC0
          Inlet                          30    -10    -5     0    50    60    75
RP/0/0RP0RSP0/CPU0:router# show environment temperatures
  
  R/S/I   Modules         Inlet           Exhaust         Hotspot
                          Temperature     Temperature     Temperature
                          (deg C)         (deg C)         (deg C)
  
  0/2/*   host              31, 27         43, 45         48
          cpu                                             31
          fabricq0                                        46
          fabricq1                                        44
          ingressq                                        34
          egressq                          41             43
          ingresspse                                      35
          egresspse                                       42
          plimasic          30, 31         42
  0/RP1/* host              38                            44
          cpu                                             36
          ingressq                                        42
          fabricq0                                        43
  0/SM0/* host              29, 29                        41, 33
    
RP/0/RSP0/CPU0:router# show env temperatures

Sun Aug  8 23:18:15.153 ABC

R/S/I   Modules         Inlet           Hotspot
                        Temperature     Temperature
                        (deg C)         (deg C)
 
0/RSP0/*
        host              21.2           30.8         
0/RSP1/*
        host              20.5           30.3         
0/5/*
        host              23.2           30.9    
  

Table 1 describes the significant fields shown in the display.

Table 2  show environment temperatures Field Descriptions

Field

Description

R/S/I

Rack number, slot number, and interface for which information is displayed, in the format rack/slot/module.

Modules

Module for which temperature information is displayed.

Inlet Temperature (deg C)

Current temperature of the inlet sensor, in degrees Celsius.

Note   

The inlet temperature corresponds to the room air temperature entering the router.

Exhaust Temperature (deg C)

Current temperature of the exhaust sensor, in degrees Celsius.

Note   

The exhaust temperature corresponds to the air being exhausted from the router.

Hotspot Temperature (deg C)

Current temperature of the hotspot, in degrees Celsius.

The following example shows sample output from the show environment command the with the leds keyword:

RP/0/0RP0RSP0/CPU0:router# show environment leds
  
  0/2/*: Module (host) LED status says: OK
  0/2/*: Module (plimasic) LED status says: OK
  0/SM0/*: Module (host) LED status says: OK
    
RP/0/RSP0/CPU0:router# show env leds

Sun Aug  8 23:18:19.416 ABC
R/S/I   Modules LED             Status
0/RSP0/*
        host    Critical-Alarm  Off
        host    Major-Alarm     Off
        host    Minor-Alarm     Off
        host    ACO             Off
        host    Fail            Off
0/RSP1/*
        host    Critical-Alarm  On
        host    Major-Alarm     Off
        host    Minor-Alarm     Off
        host    ACO             Off
        host    Fail            Off
  

Table 2describes the significant fields shown in the display.

Table 3  show environment leds Field Descriptions

Field

Description

rack_num/slot_num/*:

Rack number and slot number where the node resides.

Module (host) LED status says:

Current LED status of the specified node.

The following example shows sample output from the show environment command the with the power-supply keyword:

RP/0/0RP0RSP0/CPU0:router # show environment power
CHASSIS LEVEL POWER INFO: chassisinfo
================================================================================
   Total output power capacity (Shelf 0 + Shelf 1) :       0W +   12000W
   Total output power required                     :    6500W
   Total power input                               :    1341W
   Total power output                              :     964W

Power Shelf 0:
================================================================================
   Power       Supply     ------Input----   ------Output---      Status
   Module      Type        Volts     Amps    Volts     Amps
================================================================================
   0/PT1-PM0   3KW-AC      213.5      1.5     55.5      4.1    OK
   0/PT1-PM1   3KW-AC      212.9      1.6     55.4      4.4    OK
   0/PT1-PM2   3KW-AC      212.9      1.6     55.4      4.5    OK
   0/PT1-PM3   3KW-AC      212.0      1.6     55.4      4.4    OK
   0/PT1-PM4      -          0.0      0.0      0.0      0.0    NOT PRESENT
   0/PT1-PM5      -          0.0      0.0      0.0      0.0    NOT PRESENT

Total of Power Shelf 0:        1341W/ 6.3A        964W/17.4A
RP/0/RP0/CPU0:router(admin)# show env power-supply

Thu Aug  5 00:18:29.492 DST
                Power Supply        Voltage        Current
                AC-REC AC-REC        (V)              (A)
 Zone 1:        [A], [B]        54.965, 54.181   3.447,  4.073
 Zone 2:        [A], [B]        54.671, 54.083   8.983,  8.670
 Zone 3:        [A], [B]        55.063, 54.279   3.865,  4.073

 Total Current:   33.111 A
 Total Power  : 1804.049 W
  
RP/0/5/CPU0:router(admin)# show env power-supply
Thu Aug  5 07:42:49.259 DST
                   48V       Current
R/S/I     Module   (V)         (A)
0/24/*    PEM1     No Module Present
          PEM2      52         15       PWR-GSR6-AC= Standard AC PS
0/25/*    PEM1     No Module Present
          PEM2      52         16       PWR-GSR6-AC= Standard AC PS
  
RP/0/RSP0/CPU0:router(admin)# show environment power-supply

Wed Aug  4 23:38:25.033 DST
R/S/I   Modules         Capacity        Status
                        (W)
0/PM0/*
        host    PM      3000            Ok
0/PM1/*
        host    PM      3000            Ok
0/PM2/*
        host    PM      3000            Ok

R/S/I   Power Draw      Voltage         Current
        (W)             (V)             (A)
0/PM0/* 494.9           53.8            9.2
0/PM1/* 581.0           53.8            10.8
0/PM2/* 0.0             54.1            0.0
--------------
Total:  1075.9

Power Shelves Type: AC

Total Power Capacity:                           9000W
Usable Power Capacity:                          9000W
Supply Failure Protected Capacity:              6000W
Feed Failure Protected Capacity:                3000W
Worst Case Power Used:                          2720W

 Slot                                                      Max Watts
 ----                                                      ---------
 0/1/CPU0                                                        350
 0/RSP0/CPU0                                                     235
 0/RSP1/CPU0                                                     235  (default)
 0/4/CPU0                                                        350
 0/6/CPU0                                                        350
 0/FT0/SP                                                        600
 0/FT1/SP                                                        600

Worst Case Power Available:             6280W
Supply Protected Capacity Available:    3280W
Feed Protected Capacity Available:       280W
  
This table describes the significant fields shown in the display.

Table 4  show environment power-supply Field Descriptions

Field

Description

R/S/I

Rack number, slot number, and interface for which information is displayed, in the format PEM/Power Module/* (for example 0/PM0/*).

Modules

Module for which power information is displayed.

Capacity

Power capacity of each power module in Watts.

Status

Operational status of power modules.

Power Draw

Real (measured) power drawn from each power module.

Voltage

Real (measured) power module voltage.

Current

Real (measured) power module current draw.

Power Shelves Type

AC or DC.

Total Power Capacity

Sum of the power capacity of each of the modules installed in the chassis.

Usable Power Capacity

Sum of the power capacity of each of the powered and operational power modules installed in the chassis.

Supply Failure Protected Capacity

Protected power capacity of the chassis with power module redundancy (ASR 9010 AC 3+3, ASR 9010 DC 5+1, ASR 9006 AC 2+1, ASR 9010 DC 2+1).

Feed Failure Protected Capacity

Feed protected power capacity. This value applies to the ASR 9010 AC system only.

Worst Case Power Used

Sum of the estimated power draw of each of the load modules in the chassis. Load modules can be fan trays, RSPs and line cards.

Worst Case Power Available

Usable power capacity minus the worst case power used.

Supply Protected Capacity Available

Supply failure protected capacity minus the worst case power used.

Feed Protected Capacity Available

Feed failure protected capacity minus the worst case power used.

show fpd package

To display which shared port adapters (SPA) and SPA interface processors (SIPs) are supported with your current Cisco IOS XR software release, which field-programmable device (FPD) image you need for each SPA and SIP, and what the minimum hardware requirements are for the SPA and SIP modules, use the show fpd package command in administration EXEC mode.

show fpd package

Syntax Description

This command has no keywords or arguments.

Command Default

No default behavior or values

Command Modes

Administration EXEC

System Admin EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Release 5.0.0

This command was introduced.

Release 3.4.1

The show fpd package command output was updated to display the ROMMON images.

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

If there are multiple FPD images for your card, use the show fpd package command to determine which FPD image to use if you only want to upgrade a specific FPD type.

Task ID

Task ID

Operations

sysmgr

read

Examples

The following example shows sample output from the show fpd package command:

sysadmin_vm:0_RP1 # show fpd package
PROTO-CXP-2XPITA     BAO-MB FPGA                NO      1.00      1.00      0.0 
                     Slice-0 GN2411             YES     3.01      3.01      2.0 
                     Slice-1 GN2411             YES     3.01      3.01      2.0 
                     Slice-0 GN2411             YES     2.07      2.07      0.0 
                     Slice-1 GN2411             YES     2.07      2.07      0.0 
                     CCC FPGA                   YES     1.14      1.14      0.0 
                     CCC Power-On               YES     1.30      1.30      0.0 
                     Ethernet Switch            YES     1.32      1.32      0.0 
                     BIOS FPD                   YES     9.10      9.10      0.0 
                     SB Certificates            NO      1.00      1.00      0.0 
--------------------------------------------------------------------------------
NC6-FANTRAY          Fantray FPGA               NO      2.01      2.01      0.0 
--------------------------------------------------------------------------------
PWR-3KW-AC-V2        DT-PriMCU                  NO      6.01      6.01      1.0 
                     DT-Sec54vMCU               NO      6.01      6.01      1.0 
                     DT-Sec5vMCU                NO      6.03      6.03      1.0 
                     EM-Sec54vMCU               NO      3.08      3.08      0.21
                     EM-Sec5vMCU                NO      3.06      3.06      0.21
--------------------------------------------------------------------------------
PWR-2KW-DC-V2        DT-PriMCU                  NO      6.02      6.02      0.12
                     DT-Sec54vMCU               NO      6.02      6.02      0.12
                     DT-Sec5vMCU                NO      6.02      6.02      0.12
                     EM-PriMCU                  NO      3.06      3.06      0.21
                     EM-Sec54vMCU               NO      3.09      3.09      0.21
                     EM-Sec5vMCU                NO      3.07      3.07      0.21
--------------------------------------------------------------------------------
NC6-10X100G-L-K      BAO-MB FPGA                NO      1.00      1.00      0.0 
                     BAO-DB FPGA                NO      1.00      1.00      0.0 
                     S2 GN2411                  YES     3.01      3.01      2.0 
                     S3 GN2411                  YES     3.01      3.01      2.0 
                     S4 GN2411                  YES     3.01      3.01      2.0 
                     S2 GN2411                  YES     2.07      2.07      0.0 
                     S3 GN2411                  YES     2.07      2.07      0.0 
                     S4 GN2411                  YES     2.07      2.07      0.0 
                     CCC FPGA                   YES     1.14      1.14      0.0 
                     CCC Power-On               YES     1.30      1.30      0.0 
                     Ethernet Switch            YES     1.32      1.32      0.0 
                     BIOS FPD                   YES     9.10      9.10      0.0 
                     SB Certificates            NO      1.00      1.00      0.0 
--------------------------------------------------------------------------------
NC6-10X100G-M-K      BAO-MB FPGA                NO      1.00      1.00      0.0 
                     BAO-DB FPGA                NO      1.00      1.00      0.0 
                     S2 GN2411                  YES     3.01      3.01      2.0 
                     S3 GN2411                  YES     3.01      3.01      2.0 
                     S4 GN2411                  YES     3.01      3.01      2.0 
                     S2 GN2411                  YES     2.07      2.07      0.0 
                     S3 GN2411                  YES     2.07      2.07      0.0 
                     S4 GN2411                  YES     2.07      2.07      0.0 
                     CPAK bay 0 FPD             YES     1.13      1.13      0.0 
                     CPAK bay 1 FPD             YES     1.13      1.13      0.0 
                     CPAK bay 2 FPD             YES     1.13      1.13      0.0 
                     CPAK bay 3 FPD             YES     1.13      1.13      0.0 
                     CPAK bay 4 FPD             YES     1.13      1.13      0.0 
                     CPAK bay 5 FPD             YES     1.13      1.13      0.0 
                     CPAK bay 6 FPD             YES     1.13      1.13      0.0 
                     CPAK bay 7 FPD             YES     1.13      1.13      0.0 
                     CPAK bay 8 FPD             YES     1.13      1.13      0.0 
                     CPAK bay 9 FPD             YES     1.13      1.13      0.0 
                     CCC FPGA                   YES     1.14      1.14      0.0 
                     CCC Power-On               YES     1.30      1.30      0.0 
                     Ethernet Switch            YES     1.32      1.32      0.0 
                     SB Certificates            NO      1.00      1.00      0.0 
--------------------------------------------------------------------------------
NC6-10X100G-L-P      BAO-MB FPGA                NO      1.00      1.00      0.0 
                     BAO-DB FPGA                NO      1.00      1.00      0.0 
                     Slice-0 GN2411             YES     3.01      3.01      2.0 
                     Slice-1 GN2411             YES     3.01      3.01      2.0 
                     Slice-0 GN2411             YES     2.07      2.07      0.0 
                     Slice-1 GN2411             YES     2.07      2.07      0.0 
                     Slice-2 GN2411             YES     3.01      3.01      2.0 
                     Slice-3 GN2411             YES     3.01      3.01      2.0 
                     Slice-4 GN2411             YES     3.01      3.01      2.0 
                     Slice-2 GN2411             YES     2.07      2.07      0.0 
                     Slice-3 GN2411             YES     2.07      2.07      0.0 
                     Slice-4 GN2411             YES     2.07      2.07      0.0 
                     S2 GN2411                  YES     3.01      3.01      2.0 
                     S3 GN2411                  YES     3.01      3.01      2.0 
                     S4 GN2411                  YES     3.01      3.01      2.0 
                     S2 GN2411                  YES     2.07      2.07      0.0 
                     S3 GN2411                  YES     2.07      2.07      0.0 
                     S4 GN2411                  YES     2.07      2.07      0.0 
                     CCC FPGA                   YES     1.14      1.14      0.0 
                     CCC Power-On               YES     1.30      1.30      0.0 
                     Ethernet Switch            YES     1.32      1.32      0.0 
                     BIOS FPD                   YES     9.10      9.10      0.0 
                     SB Certificates            NO      1.00      1.00      0.0 
--------------------------------------------------------------------------------
NC6-6-10X100G-L-K    BAO-MB FPGA                NO      1.00      1.00      0.0 
                     BAO-DB FPGA                NO      1.00      1.00      0.0 
                     Slice-0 GN2411             YES     2.07      2.07      0.0 
                     Slice-1 GN2411             YES     2.07      2.07      0.0 
                     Slice-2 GN2411             YES     2.07      2.07      0.0 
                     Slice-3 GN2411             YES     2.07      2.07      0.0 
                     Slice-4 GN2411             YES     2.07      2.07      0.0 
                     S2 GN2411                  YES     2.07      2.07      0.0 
                     S3 GN2411                  YES     2.07      2.07      0.0 
                     S4 GN2411                  YES     2.07      2.07      0.0 
                     CCC FPGA                   YES     1.14      1.14      0.0 
                     CCC Power-On               YES     1.30      1.30      0.0 








RP/0/RP0/CPU0:Router# admin
RP/0/RP0/CPU0:Router(admin)# show fpd package 

Thu Jun 24 10:58:49.319 UTC

=============================== ================================================
                                        Field Programmable Device Package
                                ================================================
                                                                 SW      Min Req   Min Req
Card Type            FPD Description            Type Subtype   Version   SW Ver    HW Vers
==================== ========================== ==== ======= =========== ========  =========
1OC768-ITU/C         OPTICS FIRMWARE 104B4      lc   fpga2     104.04        0.0       0.0  
----------------------------------------------------------------------------------------------
1OC768-DWDM-L        OPTICS FIRMWARE 104B4      lc   fpga2     104.04        0.0       0.0  
----------------------------------------------------------------------------------------------
1OC768-DPSK/C        OPTICS FIRMWARE 101B3      lc   fpga2     101.03        0.0       0.0  
----------------------------------------------------------------------------------------------
1OC768-DPSK/C-O      OPTICS FIRMWARE 101B3      lc   fpga2     101.03        0.0       0.0  
----------------------------------------------------------------------------------------------
1OC768-DPSK/C-E      OPTICS FIRMWARE 101B3      lc   fpga2     101.03        0.0       0.0  
----------------------------------------------------------------------------------------------
CRS-ADVSVC-PLIM      FPGA mCPU0 0.557           lc   fpga2       0.557       0.0       0.0  
                     FPGA sCPU0 0.557           lc   fpga3       0.557       0.0       0.0  
                     FPGA mCPU1 0.557           lc   fpga4       0.557       0.0       0.0  
                     FPGA sCPU1 0.557           lc   fpga5       0.557       0.0       0.0  
                     FPGA PLIM_SVC 0.41013      lc   fpga1       0.41013     0.0       0.0  
----------------------------------------------------------------------------------------------
CRS1-SIP-800         JACKET FPGA swv6.0         lc   fpga1       6.00        5.0       0.0  
                     FPGA swv6.0 hwv80          lc   fpga1       6.00        5.0       0.80 
----------------------------------------------------------------------------------------------
8-10GBE              FPGA swvA.0                lc   fpga1      10.00        0.0       0.0  
----------------------------------------------------------------------------------------------
OC48-POS-16-ED       FPGA PLIM_OC48 9.0         lc   fpga1       9.00        0.0       0.0  
----------------------------------------------------------------------------------------------
4-10GE               SQUIRREL FPGA 10.0         lc   fpga1      10.00        0.0       0.0  
----------------------------------------------------------------------------------------------
42-1GE               FPGA swv6.0                lc   fpga1       6.00        0.0       0.0  
                     FPGA swv6.0 hwv0.80        lc   fpga1       6.00        0.0       0.80 
----------------------------------------------------------------------------------------------
20-1GE-FLEX          FPGA swv6.0                lc   fpga1       6.00        0.0       0.0  
                     FPGA swv6.0 hwv0.80        lc   fpga1       6.00        0.0       0.80 
----------------------------------------------------------------------------------------------
2-10GE-WL-FLEX       FPGA swv6.0                lc   fpga1       6.00        0.0       0.0  
                     FPGA swv6.0 hwv0.80        lc   fpga1       6.00        0.0       0.80 
----------------------------------------------------------------------------------------------
Route Processor      ROMMONA swv1.54 asmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONA swv1.54 dsmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 asmp       lc   rommon      1.54        0.0       0.0  
                     ROMMONB swv1.54 dsmp       lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
SC                   ROMMONA swv1.54 asmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONA swv1.54 dsmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 asmp       lc   rommon      1.54        0.0       0.0  
                     ROMMONB swv1.54 dsmp       lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
RP                   ROMMONA swv1.54 asmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONA swv1.54 dsmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 asmp       lc   rommon      1.54        0.0       0.0  
                     ROMMONB swv1.54 dsmp       lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
Shelf Controller GE  ROMMONA swv1.54 asmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONA swv1.54 dsmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 asmp       lc   rommon      1.54        0.0       0.0  
                     ROMMONB swv1.54 dsmp       lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
RP                   ROMMONA swv1.54 asmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONA swv1.54 dsmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 asmp       lc   rommon      1.54        0.0       0.0  
                     ROMMONB swv1.54 dsmp       lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
Shelf Controller GE2 ROMMONA swv1.54 asmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONA swv1.54 dsmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 asmp       lc   rommon      1.54        0.0       0.0  
                     ROMMONB swv1.54 dsmp       lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
DRP                  ROMMONA swv1.54 asmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONA swv1.54 dsmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONA swv1.54 sp         lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 asmp       lc   rommon      1.54        0.0       0.0  
                     ROMMONB swv1.54 dsmp       lc   rommon      1.54        0.0       0.0  
                     ROMMONB swv1.54 sp         lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
DRP_B                ROMMONA swv1.54 asmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONA swv1.54 dsmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONA swv1.54 sp         lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 asmp       lc   rommon      1.54        0.0       0.0  
                     ROMMONB swv1.54 dsmp       lc   rommon      1.54        0.0       0.0  
                     ROMMONB swv1.54 sp         lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
S1S2S3               ROMMONA swv1.54 sp         lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 sp         lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
S1S3                 ROMMONA swv1.54 sp         lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 sp         lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
S2                   ROMMONA swv1.54 sp         lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 sp         lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
Fabric HS123         ROMMONA swv1.54 sp         lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 sp         lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
Fabric HS123 Star    ROMMONA swv1.54 sp         lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 sp         lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
Fabric HS13 Star     ROMMONA swv1.54 sp         lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 sp         lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
Fabric QQS123        ROMMONA swv1.54 sp         lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 sp         lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
LED                  ROMMONA swv1.54 sp         lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 sp         lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
40G-MSC              ROMMONA swv1.54 asmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONA swv1.54 dsmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONA swv1.54 sp         lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 asmp       lc   rommon      1.54        0.0       0.0  
                     ROMMONB swv1.54 dsmp       lc   rommon      1.54        0.0       0.0  
                     ROMMONB swv1.54 sp         lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
MSC_B                ROMMONA swv1.54 asmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONA swv1.54 dsmp       lc   rommonA     1.52        0.0       0.0  
                     ROMMONA swv1.54 sp         lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 asmp       lc   rommon      1.54        0.0       0.0  
                     ROMMONB swv1.54 dsmp       lc   rommon      1.54        0.0       0.0  
                     ROMMONB swv1.54 sp         lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
FP40                 ROMMONA swv1.54 asmp       lc   rommonA     1.53        0.0       0.0  
                     ROMMONA swv1.54 dsmp       lc   rommonA     1.53        0.0       0.0  
                     ROMMONA swv1.54 sp         lc   rommonA     1.53        0.0       0.0  
                     ROMMONB swv1.54 asmp       lc   rommon      1.54        0.0       0.0  
                     ROMMONB swv1.54 dsmp       lc   rommon      1.54        0.0       0.0  
                     ROMMONB swv1.54 sp         lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
PSAL                 ROMMONA swv1.54 sp         lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 sp         lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
Unknown              ROMMONA swv1.54 sp         lc   rommonA     1.54        0.0       0.0  
                     ROMMONB swv1.54 sp         lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
FAN                  ROMMONA swv1.54 sp         lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 sp         lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
FC Fan Controller    ROMMONA swv1.54 sp         lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 sp         lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
LED                  ROMMONA swv1.54 sp         lc   rommonA     1.52        0.0       0.0  
                     ROMMONB swv1.54 sp         lc   rommon      1.54        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-4XT3/E3          SPA E3 Subrate FPGA        spa  fpga2       1.04        0.0       0.0  
                     SPA T3 Subrate FPGA        spa  fpga3       1.04        0.0       0.0  
                     SPA I/O FPGA               spa  fpga1       1.00        0.0       0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-2XT3/E3          SPA E3 Subrate FPGA        spa  fpga2       1.04        0.0       0.0  
                     SPA T3 Subrate FPGA        spa  fpga3       1.04        0.0       0.0  
                     SPA I/O FPGA               spa  fpga1       1.00        0.0       0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-OC192POS         SPA FPGA swv1.3            spa  fpga1       1.03        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-8XOC12-POS       SPA FPGA swv1.0            spa  fpga1       1.00        0.0       0.5  
----------------------------------------------------------------------------------------------
SPA-4XOC3-POS        SPA FPGA swv3.4            spa  fpga1       3.04        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-OC192POS-XFP     SPA FPGA swv1.2            spa  fpga1       1.02        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-8X1GE            SPA FPGA swv1.8            spa  fpga1       1.08        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-2XOC48POS/RPR    SPA FPGA swv1.0            spa  fpga1       1.00        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-4XOC48POS/RPR    SPA FPGA swv1.0            spa  fpga1       1.00        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-10X1GE-V2        SPA FPGA swv1.10           spa  fpga1       1.10        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-8X1GE-V2         SPA FPGA swv1.10           spa  fpga1       1.10        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-5X1GE-V2         SPA FPGA swv1.10           spa  fpga1       1.10        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-1X10GE-L-V2      SPA FPGA swv1.9            spa  fpga1       1.09        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-1X10GE-WL-V2     SPA FPGA swv1.11           spa  fpga1       1.11        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-1XOC3-ATM-V2     SPA FPGA swv1.2            spa  fpga1       1.03        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-2XOC3-ATM-V2     SPA FPGA swv1.2            spa  fpga1       1.03        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-3XOC3-ATM-V2     SPA FPGA swv1.2            spa  fpga1       1.03        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-1XOC12-ATM-V2    SPA FPGA swv1.2            spa  fpga1       1.03        0.0       0.0  
----------------------------------------------------------------------------------------------
  
RP/0/0/CPU0:Router# admin
Thu Jul  7 04:40:30.631 DST

=============================== ================================================
                                        Field Programmable Device Package
                                ================================================
                                                                 SW      Min Req   Min Req
Card Type            FPD Description            Type Subtype   Version   SW Ver    HW Vers
==================== ========================== ==== ======= =========== ========  =========
E3-OC12-ATM-4        CIS1 FPGA                  lc   fpga2   40971.00        0.0       0.0  
                     IOB FPGA                   lc   fpga3   41091.00        0.0       0.0  
                     SAF 0 FPGA                 lc   fpga4   45586.00        0.0       0.0  
                     CIS2 FPGA                  lc   fpga1   40977.00        0.0       0.0  
----------------------------------------------------------------------------------------------
E3-OC3-ATM-4         CIS1 FPGA                  lc   fpga2   40971.00        0.0       0.0  
                     IOB FPGA                   lc   fpga3   41091.00        0.0       0.0  
                     SAF 0 FPGA                 lc   fpga4   45586.00        0.0       0.0  
                     CIS2 FPGA                  lc   fpga1   40977.00        0.0       0.0  
----------------------------------------------------------------------------------------------
12000-ServEngCard    TREX FPGA                  lc   fpga2     162.45        0.0       0.0  
                     TREX FPGA                  lc   fpga1       0.41257     0.0       0.0  
----------------------------------------------------------------------------------------------
12000-SIP            HABANERO FPGA              lc   fpga2     240.03        0.0       0.0  
                     JALAPENO FPGA              lc   fpga5     240.13        0.0       0.0  
                     JALAPENO FPGA              lc   fpga5     240.13        0.0       0.0  
                     JALAPENO FPGA              lc   fpga1     255.23        0.0       0.0  
----------------------------------------------------------------------------------------------
E3-OC12-CH-1         Shiver FPGA                lc   fpga1       1.02        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-IPSEC-2G         Sequoia                    spa  fpga2       1.01        0.0       1.0  
                     Lodi                       spa  fpga1       1.22        0.0       1.0  
                     SPA PROM                   spa  rommon      1.01        0.0       1.0  
----------------------------------------------------------------------------------------------
SPA-4XT3/E3          SPA E3 Subrate FPGA        spa  fpga2       1.04        0.0       0.0  
                     SPA T3 Subrate FPGA        spa  fpga3       1.04        0.0       0.0  
                     SPA I/O FPGA               spa  fpga1       1.01        0.0       0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-2XT3/E3          SPA E3 Subrate FPGA        spa  fpga2       1.04        0.0       0.0  
                     SPA T3 Subrate FPGA        spa  fpga3       1.04        0.0       0.0  
                     SPA I/O FPGA               spa  fpga1       1.01        0.0       0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-4XCT3/DS0        SPA T3 Subrate FPGA        spa  fpga2       0.11        0.0       0.100
                     SPA T3 Subrate FPGA        spa  fpga2       1.04        0.0       0.200
                     SPA I/O FPGA               spa  fpga1       2.08        0.0       0.100
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.100
----------------------------------------------------------------------------------------------
SPA-2XCT3/DS0        SPA T3 Subrate FPGA        spa  fpga2       0.11        0.0       0.100
                     SPA T3 Subrate FPGA        spa  fpga2       1.04        0.0       0.200
                     SPA I/O FPGA               spa  fpga1       2.08        0.0       0.100
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.100
----------------------------------------------------------------------------------------------
SPA-1XCHSTM1/OC3     SPA T3 Subrate FPGA        spa  fpga2       1.04        0.0       0.0  
                     SPA I/O FPGA               spa  fpga1       1.08        0.0       0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-24CHT1-CE-ATM    SPA T3 Subrate FPGA        spa  fpga2       1.10        0.0       1.0  
                     SPA I/O FPGA               spa  fpga1       2.32        0.0       1.0  
                     SPA ROMMON                 spa  rommon      1.03        0.0       1.0  
----------------------------------------------------------------------------------------------
SPA-2CHT3-CE-ATM     SPA T3 Subrate FPGA        spa  fpga2       1.10        0.0       1.0  
                     SPA I/O FPGA               spa  fpga1       2.22        0.0       1.0  
                     SPA ROMMON                 spa  rommon      1.04        0.0       1.0  
----------------------------------------------------------------------------------------------
SPA-1CHOC3-CE-ATM    SPA OC3 Subrate FPGA       spa  fpga2       1.00        0.0       2.0  
                     SPA I/O FPGA               spa  fpga1       2.23        0.0       2.0  
                     SPA ROMMON                 spa  rommon      1.04        0.0       2.0  
----------------------------------------------------------------------------------------------
SPA-IPSEC-2G-2       Sequoia                    spa  fpga2       1.01        0.0       1.0  
                     Lodi                       spa  fpga1       1.22        0.0       1.0  
                     SPA PROM                   spa  rommon      1.01        0.0       1.0  
----------------------------------------------------------------------------------------------
SPA-1XCHOC48/DS3     SPA I/O FPGA               spa  fpga2       1.00        0.0       0.49 
                     SPA I/O FPGA               spa  fpga3       1.00        0.0       0.52 
                     SPA I/O FPGA               spa  fpga1       1.36        0.0       0.49 
                     SPA ROMMON                 spa  rommon      2.02        0.0       0.49 
----------------------------------------------------------------------------------------------
SPA-1XCHOC12/DS0     SPA I/O FPGA               spa  fpga2       1.00        0.0       0.49 
                     SPA I/O FPGA               spa  fpga1       1.36        0.0       0.49 
                     SPA ROMMON                 spa  rommon      2.02        0.0       0.49 
----------------------------------------------------------------------------------------------
SPA-OC192POS         SPA FPGA swv1.2            spa  fpga1       1.02        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-8XOC12-POS       SPA FPGA swv1.0            spa  fpga1       1.00        0.0       0.5  
----------------------------------------------------------------------------------------------
SPA-8XCHT1/E1        SPA I/O FPGA               spa  fpga1       2.08        0.0       0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.140
----------------------------------------------------------------------------------------------
SPA-OC192POS-XFP     SPA FPGA swv1.2            spa  fpga1       1.02        0.0       0.0  
                     SPA FPGA swv1.2 hwv2       spa  fpga1       1.02        0.0       2.0  
----------------------------------------------------------------------------------------------
SPA-10X1GE           SPA FPGA swv1.10           spa  fpga1       1.10        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-5X1GE            SPA FPGA swv1.10           spa  fpga1       1.10        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-2XOC48POS/RPR    SPA FPGA swv1.0            spa  fpga1       1.00        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-4XOC48POS/RPR    SPA FPGA swv1.0            spa  fpga1       1.00        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-1XTENGE-XFP      SPA FPGA swv1.9            spa  fpga1       1.09        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-8X1FE            SPA FPGA swv1.1            spa  fpga1       1.01        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-1XOC48POS/RPR    SPA FPGA swv1.2            spa  fpga1       1.02        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-8XOC3-POS        SPA FPGA swv1.0            spa  fpga1       1.00        0.0       0.5  
----------------------------------------------------------------------------------------------
SPA-2XOC12-POS       SPA FPGA swv1.0            spa  fpga1       1.00        0.0       0.5  
----------------------------------------------------------------------------------------------
SPA-4XOC12-POS       SPA FPGA swv1.0            spa  fpga1       1.00        0.0       0.5  
----------------------------------------------------------------------------------------------
SPA-10X1GE-V2        SPA FPGA swv1.10           spa  fpga1       1.10        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-8X1GE-V2         SPA FPGA swv1.10           spa  fpga1       1.10        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-5X1GE-V2         SPA FPGA swv1.10           spa  fpga1       1.10        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-2X1GE-V2         SPA FPGA swv1.1            spa  fpga1       1.01        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-1X10GE-L-V2      SPA FPGA swv1.11           spa  fpga1       1.11        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-8X1FE-V2         SPA FPGA swv1.1            spa  fpga1       1.01        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-4XOC3-POS-V2     SPA FPGA swv1.0            spa  fpga1       1.00        0.0       0.5  
----------------------------------------------------------------------------------------------
SPA-1X10GE-L-IT      SPA FPGA swv1.0            spa  fpga1       1.00        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-1XOC3-ATM-V2     TATM SPA IOFPGA            spa  fpga1       2.02        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-2XOC3-ATM-V2     SPA TATM IOFPGA            spa  fpga1       2.02        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-3XOC3-ATM-V2     SPA TATM IOFPGA            spa  fpga1       2.02        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-1XOC12-ATM-V2    SPA TATM IOFPGA            spa  fpga1       2.02        0.0       0.0  
----------------------------------------------------------------------------------------------
   
RP/0/RP1/CPU0:router(admin)# show fpd package

Thu Jul  7 04:34:48.351 DST

=============================== ================================================
                                        Field Programmable Device Package
                                ================================================
                                                                 SW      Min Req   Min Req
Card Type            FPD Description            Type Subtype   Version   SW Ver    HW Vers
==================== ========================== ==== ======= =========== ========  =========
A9K-40GE-B           Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.06        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONA LC2                lc   rommonA     1.05        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-4T-B             Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.0       0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.0       0.1  
                     PHY LC2                    lc   fpga3      14.44        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-8T/4-B           Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.0       0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.0       0.1  
                     PHY LC2                    lc   fpga3      14.44        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-2T20GE-B         Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.11        0.0       0.1  
                     LCClkCtrl LC2              lc   cpld3       0.09        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.16        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-40GE-E           Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.06        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONA LC2                lc   rommonA     1.05        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-4T-E             Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.0       0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.0       0.1  
                     PHY LC2                    lc   fpga3      14.44        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-8T/4-E           Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.0       0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.0       0.1  
                     PHY LC2                    lc   fpga3      14.44        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-2T20GE-E         Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.11        0.0       0.1  
                     LCClkCtrl LC2              lc   cpld3       0.09        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.16        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-8T-B             Can Bus Ctrl (CBC) LC3     lc   cbc         6.02        0.0       0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     PHYCtrl LC3                lc   cpld2       0.08        0.0       0.1  
                     LCClkCtrl LC3              lc   cpld3       0.03        0.0       0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.11        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-16T/8-B          Can Bus Ctrl (CBC) LC3     lc   cbc         6.02        0.0       0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     PHYCtrl LC3                lc   cpld2       0.04        0.0       0.1  
                     LCClkCtrl LC3              lc   cpld3       0.01        0.0       0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.01        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-16T/8-B          Can Bus Ctrl (CBC) LC3     lc   cbc         6.02        0.0       0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     PHYCtrl LC3                lc   cpld2       0.04        0.0       0.1  
                     LCClkCtrl LC3              lc   cpld3       0.01        0.0       0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.01        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-8T-E             Can Bus Ctrl (CBC) LC3     lc   cbc         6.02        0.0       0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     PHYCtrl LC3                lc   cpld2       0.08        0.0       0.1  
                     LCClkCtrl LC3              lc   cpld3       0.03        0.0       0.1  
                     CPUCtrl LC3                lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.11        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-16T/8-E          Can Bus Ctrl (CBC) LC3     lc   cbc         6.02        0.0       0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     PHYCtrl LC3                lc   cpld2       0.04        0.0       0.1  
                     LCClkCtrl LC3              lc   cpld3       0.01        0.0       0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.01        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-16T/8-E          Can Bus Ctrl (CBC) LC3     lc   cbc         6.02        0.0       0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     PHYCtrl LC3                lc   cpld2       0.04        0.0       0.1  
                     LCClkCtrl LC3              lc   cpld3       0.01        0.0       0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.01        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-40GE-L           Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.06        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-4T-L             Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.0       0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.0       0.1  
                     Serdes Upgrade LC2         lc   fpga3      14.44        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-8T/4-L           Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.0       0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.0       0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.0       0.1  
                     Serdes Upgrade LC2         lc   fpga3      14.44        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-2T20GE-L         Can Bus Ctrl (CBC) LC2     lc   cbc         2.02        0.0       0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.0       0.1  
                     PHYCtrl LC2                lc   cpld2       0.11        0.0       0.1  
                     LCClkCtrl LC2              lc   cpld3       0.09        0.0       0.1  
                     Tomcat LC2                 lc   fpga2       0.16        0.0       0.1  
                     Bridge LC2                 lc   fpga1       0.43        0.0       0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-8T-L             Can Bus Ctrl (CBC) LC3     lc   cbc         6.02        0.0       0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     PHYCtrl LC3                lc   cpld2       0.08        0.0       0.1  
                     LCClkCtrl LC3              lc   cpld3       0.03        0.0       0.1  
                     CPUCtrl LC3                lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.11        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-16T/8-L          Can Bus Ctrl (CBC) LC3     lc   cbc         6.02        0.0       0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     PHYCtrl LC3                lc   cpld2       0.04        0.0       0.1  
                     LCClkCtrl LC3              lc   cpld3       0.01        0.0       0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.01        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-SIP-700          Can Bus Ctrl (CBC) LC5     lc   cbc         3.05        0.0       0.1  
                     CPUCtrl LC5                lc   cpld1       0.15        0.0       0.1  
                     QFPCPUBridge LC5           lc   fpga2       5.14        0.0       0.1  
                     NPUXBarBridge LC5          lc   fpga1       0.22        0.0       0.1  
                     ROMMONA LC5                lc   rommonA     1.03        0.0       0.1  
                     ROMMONB LC5                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-SIP-500          Can Bus Ctrl (CBC) LC5     lc   cbc         3.05        0.0       0.1  
                     CPUCtrl LC5                lc   cpld1       0.15        0.0       0.1  
                     QFPCPUBridge LC5           lc   fpga2       5.14        0.0       0.1  
                     NPUXBarBridge LC5          lc   fpga1       0.22        0.0       0.1  
                     ROMMONA LC5                lc   rommonA     1.03        0.0       0.1  
                     ROMMONB LC5                lc   rommon      1.03        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-RSP-2G           Can Bus Ctrl (CBC) RSP2    lc   cbc         1.02        0.0       0.1  
                     CPUCtrl RSP2               lc   cpld2       1.17        0.0       0.1  
                     IntCtrl RSP2               lc   fpga2       1.15        0.0       0.1  
                     ClkCtrl RSP2               lc   fpga3       1.23        0.0       0.1  
                     UTI RSP2                   lc   fpga4       3.08        0.0       0.1  
                     PUNT RSP2                  lc   fpga1       1.05        0.0       0.1  
                     HSBI RSP2                  lc   hsbi        4.00        0.0       0.1  
                     ROMMONA RSP2               lc   rommonA     1.05        0.0       0.1  
                     ROMMONB RSP2               lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-RSP-4G           Can Bus Ctrl (CBC) RSP2    lc   cbc         1.02        0.0       0.1  
                     CPUCtrl RSP2               lc   cpld2       1.17        0.0       0.1  
                     IntCtrl RSP2               lc   fpga2       1.15        0.0       0.1  
                     ClkCtrl RSP2               lc   fpga3       1.23        0.0       0.1  
                     UTI RSP2                   lc   fpga4       3.08        0.0       0.1  
                     PUNT RSP2                  lc   fpga1       1.05        0.0       0.1  
                     HSBI RSP2                  lc   hsbi        4.00        0.0       0.1  
                     ROMMONA RSP2               lc   rommonA     1.05        0.0       0.1  
                     ROMMONB RSP2               lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-RSP-8G           Can Bus Ctrl (CBC) RSP2    lc   cbc         1.02        0.0       0.1  
                     CPUCtrl RSP2               lc   cpld2       1.17        0.0       0.1  
                     IntCtrl RSP2               lc   fpga2       1.15        0.0       0.1  
                     ClkCtrl RSP2               lc   fpga3       1.23        0.0       0.1  
                     UTI RSP2                   lc   fpga4       3.08        0.0       0.1  
                     PUNT RSP2                  lc   fpga1       1.05        0.0       0.1  
                     HSBI RSP2                  lc   hsbi        4.00        0.0       0.1  
                     ROMMONA RSP2               lc   rommonA     1.05        0.0       0.1  
                     ROMMONB RSP2               lc   rommon      1.05        0.0       0.1  
----------------------------------------------------------------------------------------------
ASR-9010-FAN         Can Bus Ctrl (CBC) FAN     lc   cbc         4.00        0.0       0.1  
----------------------------------------------------------------------------------------------
ASR-9006-FAN         Can Bus Ctrl (CBC) FAN     lc   cbc         5.00        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-BPID2-10-SLOT    Can Bus Ctrl (CBC) BP2     lc   cbc         7.103       0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-BPID2-6-SLOT     Can Bus Ctrl (CBC) BP2     lc   cbc         7.103       0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-ISM-100          Can Bus Ctrl (CBC) LC6     lc   cbc        18.05        0.0       0.1  
                     CPUCtrl LC6                lc   cpld1       0.01        0.0       0.1  
                     Maintenance LC6            lc   fpga2       1.00        0.0       0.1  
                     Amistad LC6                lc   fpga1       0.25        0.0       0.20 
                     ROMMONA LC6                lc   rommonA     1.02        0.0       0.1  
                     ROMMONB LC6                lc   rommon      1.02        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-8T-B             CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     PHYCtrl LC3                lc   cpld2       0.08        0.0       0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.11        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
----------------------------------------------------------------------------------------------
A9K-8T-E             CPUCtrl LC3                lc   cpld1       1.02        0.0       0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.0       0.1  
                     PortCtrl LC3               lc   fpga2       0.11        0.0       0.1  
                     Raven LC3                  lc   fpga1       1.02        0.0       0.1  
----------------------------------------------------------------------------------------------
SPA-4XT3/E3          SPA E3 Subrate FPGA        spa  fpga2       1.04        0.0       0.0  
                     SPA T3 Subrate FPGA        spa  fpga3       1.04        0.0       0.0  
                     SPA I/O FPGA               spa  fpga1       1.01        0.0       0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-2XT3/E3          SPA E3 Subrate FPGA        spa  fpga2       1.04        0.0       0.0  
                     SPA T3 Subrate FPGA        spa  fpga3       1.04        0.0       0.0  
                     SPA I/O FPGA               spa  fpga1       1.01        0.0       0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-4XCT3/DS0        SPA T3 Subrate FPGA        spa  fpga2       0.11        0.0       0.100
                     SPA T3 Subrate FPGA        spa  fpga2       1.04        0.0       0.200
                     SPA I/O FPGA               spa  fpga1       2.08        0.0       0.100
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.100
----------------------------------------------------------------------------------------------
SPA-2XCT3/DS0        SPA T3 Subrate FPGA        spa  fpga2       0.11        0.0       0.100
                     SPA T3 Subrate FPGA        spa  fpga2       1.04        0.0       0.200
                     SPA I/O FPGA               spa  fpga1       2.08        0.0       0.100
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.100
----------------------------------------------------------------------------------------------
SPA-1XCHSTM1/OC3     SPA T3 Subrate FPGA        spa  fpga2       1.04        0.0       0.0  
                     SPA I/O FPGA               spa  fpga1       1.08        0.0       0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-1XCHOC48/DS3     SPA I/O FPGA               spa  fpga2       1.00        0.0       0.49 
                     SPA I/O FPGA               spa  fpga3       1.00        0.0       0.52 
                     SPA I/O FPGA               spa  fpga1       1.36        0.0       0.49 
                     SPA ROMMON                 spa  rommon      2.02        0.0       0.49 
----------------------------------------------------------------------------------------------
SPA-2XCHOC12/DS0     SPA FPGA2 swv1.00          spa  fpga2       1.00        0.0       0.0  
                     SPA FPGA swv1.36           spa  fpga1       1.36        0.0       0.49 
                     SPA ROMMON swv2.2          spa  rommon      2.02        0.0       0.49 
----------------------------------------------------------------------------------------------
SPA-8XOC12-POS       SPA FPGA swv1.0            spa  fpga1       1.00        0.0       0.5  
----------------------------------------------------------------------------------------------
SPA-8XCHT1/E1        SPA I/O FPGA               spa  fpga1       2.08        0.0       0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.0       0.140
----------------------------------------------------------------------------------------------
SPA-OC192POS-XFP     SPA FPGA swv1.2 hwv2       spa  fpga1       1.02        0.0       2.0  
----------------------------------------------------------------------------------------------
SPA-2XOC48POS/RPR    SPA FPGA swv1.0            spa  fpga1       1.00        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-8XOC3-POS        SPA FPGA swv1.0            spa  fpga1       1.00        0.0       0.5  
----------------------------------------------------------------------------------------------
SPA-10X1GE-V2        SPA FPGA swv1.10           spa  fpga1       1.10        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-5X1GE-V2         SPA FPGA swv1.10           spa  fpga1       1.10        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-1X10GE-L-V2      SPA FPGA swv1.9            spa  fpga1       1.09        0.0       0.0  
----------------------------------------------------------------------------------------------
SPA-4XOC3-POS-V2     SPA FPGA swv1.0            spa  fpga1       1.00        0.0       0.5  
----------------------------------------------------------------------------------------------
SPA-1X10GE-WL-V2     SPA FPGA swv1.9            spa  fpga1       1.09        0.0       0.0  
----------------------------------------------------------------------------------------------
  
This table describes the significant fields shown in the display:

Table 5  show fpd package Field Descriptions

Field

Description

Card Type

Module part number.

FPD Description

Description of all FPD images available for the SPA.

Type

Hardware type. Possible types can be:

  • spa—Shared port adapter
  • lc—Line card

Subtype

FPD subtype. These values are used in the upgrade hw-module fpd command to indicate a specific FPD image type to upgrade.

SW Version

FPD software version recommended for the associated module running the current Cisco IOS XR software.

Min Req SW Vers

Minimum required FPD image software version to operate the card. Version 0.0 indicates that a minimum required image was not programmed into the card.

Min Req HW Vers

Minimum required hardware version for the associated FPD image. A minimum hardware requirement of version 0.0 indicates that all hardware can support this FPD image version.

This example shows the output display for ASR9912 and ASR9922:

RP/0/0RP0RSP0/CPU0:router # show fpd package
=============================== ================================================
                                        Field Programmable Device Package
                                ================================================
                                                                 SW      Min Req   Min Req
Card Type            FPD Description            Type Subtype   Version   SW Ver    HW Vers
==================== ========================== ==== ======= =========== ========  =========
ASR-9912-BPID2       Can Bus Ctrl (CBC) BP2     bp   cbc         7.104       0.00      0.1  
                     Can Bus Ctrl (CBC) BP2     lc   cbc         7.104       0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9922-BPID2       Can Bus Ctrl (CBC) BP2     bp   cbc         7.104       0.00      0.1  
                     Can Bus Ctrl (CBC) BP2     lc   cbc         7.104       0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-BPID2-10-SLOT    Can Bus Ctrl (CBC) BP2     bp   cbc         7.104       0.00      0.1  
                     Can Bus Ctrl (CBC) BP2     lc   cbc         7.104       0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-BPID2-6-SLOT     Can Bus Ctrl (CBC) BP2     bp   cbc         7.104       0.00      0.1  
                     Can Bus Ctrl (CBC) BP2     lc   cbc         7.104       0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9922-SFC110      Can Bus Ctrl (CBC) MTFC    fc   cbc        28.03        0.00      0.1  
                     Fabric Ctrl0 MTFC          fc   fpga7       1.01        0.00      0.1  
                     Can Bus Ctrl (CBC) MTFC    lc   cbc        28.03        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9912-SFC110      Can Bus Ctrl (CBC) SSFC    fc   cbc        32.02        0.00      0.1  
                     Fabric Ctrl0 MTFC          fc   fpga7       1.01        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9010-FAN         Can Bus Ctrl (CBC) FAN     ft   cbc         4.02        0.00      0.1  
                     Can Bus Ctrl (CBC) FAN     lc   cbc         4.02        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9006-FAN         Can Bus Ctrl (CBC) FAN     ft   cbc         5.02        0.00      0.1  
                     Can Bus Ctrl (CBC) FAN     lc   cbc         5.02        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9922-FAN         Can Bus Ctrl (CBC) MFAN    ft   cbc        29.10        0.00      0.1  
                     Can Bus Ctrl (CBC) MFAN    lc   cbc        29.10        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9912-FAN         Can Bus Ctrl (CBC) SFAN    ft   cbc        31.03        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9010-FAN-V2      Can Bus Ctrl (CBC) FAN     ft   cbc        29.10        0.00      0.1  
                     Can Bus Ctrl (CBC) FAN     lc   cbc        29.10        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9001-FAN         Can Bus Ctrl (CBC) FAN     ft   cbc        24.114       0.00      0.1  
                     Can Bus Ctrl (CBC) FAN     lc   cbc        24.114       0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-40GE-B           Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.06        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-4T-B             Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.00      0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.00      0.1  
                     PHY LC2                    lc   fpga3      14.44        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-8T/4-B           Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.00      0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.00      0.1  
                     PHY LC2                    lc   fpga3      14.44        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-2T20GE-B         Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.11        0.00      0.1  
                     LCClkCtrl LC2              lc   cpld3       0.10        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.16        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-40GE-E           Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.06        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-4T-E             Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.00      0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.00      0.1  
                     PHY LC2                    lc   fpga3      14.44        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-8T/4-E           Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.00      0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.00      0.1  
                     PHY LC2                    lc   fpga3      14.44        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-2T20GE-E         Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.11        0.00      0.1  
                     LCClkCtrl LC2              lc   cpld3       0.10        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.16        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-8T-B             Can Bus Ctrl (CBC) LC3     lc   cbc         6.07        0.00      0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.00      0.1  
                     PHYCtrl LC3                lc   cpld2       0.08        0.00      0.1  
                     LCClkCtrl LC3              lc   cpld3       0.03        0.00      0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.00      0.1  
                     PortCtrl LC3               lc   fpga2       0.11        0.00      0.1  
                     Raven LC3                  lc   fpga1       1.03        0.00      0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-16T/8-B          Can Bus Ctrl (CBC) LC3     lc   cbc         6.08        0.00      0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.00      0.1  
                     PHYCtrl LC3                lc   cpld2       0.04        0.00      0.1  
                     LCClkCtrl LC3              lc   cpld3       0.01        0.00      0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.00      0.1  
                     PortCtrl LC3               lc   fpga2       0.01        0.00      0.1  
                     Raven LC3                  lc   fpga1       1.03        0.00      0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-8T-E             Can Bus Ctrl (CBC) LC3     lc   cbc         6.07        0.00      0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.00      0.1  
                     PHYCtrl LC3                lc   cpld2       0.08        0.00      0.1  
                     LCClkCtrl LC3              lc   cpld3       0.03        0.00      0.1  
                     CPUCtrl LC3                lc   cpld4       1.03        0.00      0.1  
                     PortCtrl LC3               lc   fpga2       0.11        0.00      0.1  
                     Raven LC3                  lc   fpga1       1.03        0.00      0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-16T/8-E          Can Bus Ctrl (CBC) LC3     lc   cbc         6.08        0.00      0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.00      0.1  
                     PHYCtrl LC3                lc   cpld2       0.04        0.00      0.1  
                     LCClkCtrl LC3              lc   cpld3       0.01        0.00      0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.00      0.1  
                     PortCtrl LC3               lc   fpga2       0.01        0.00      0.1  
                     Raven LC3                  lc   fpga1       1.03        0.00      0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-40GE-L           Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.06        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-4T-L             Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.00      0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.00      0.1  
                     Serdes Upgrade LC2         lc   fpga3      14.44        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-8T/4-L           Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.08        0.00      0.1  
                     LCClkCtrl LC2              lc   cpld3       0.03        0.00      0.1  
                     PortCtrl LC2               lc   fpga2       0.10        0.00      0.1  
                     Serdes Upgrade LC2         lc   fpga3      14.44        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-2T20GE-L         Can Bus Ctrl (CBC) LC2     lc   cbc         2.03        0.00      0.1  
                     CPUCtrl LC2                lc   cpld1       1.00        0.00      0.1  
                     PHYCtrl LC2                lc   cpld2       0.11        0.00      0.1  
                     LCClkCtrl LC2              lc   cpld3       0.10        0.00      0.1  
                     Tomcat LC2                 lc   fpga2       0.16        0.00      0.1  
                     Bridge LC2                 lc   fpga1       0.44        0.00      0.1  
                     ROMMONB LC2                lc   rommon      1.05        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-8T-L             Can Bus Ctrl (CBC) LC3     lc   cbc         6.07        0.00      0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.00      0.1  
                     PHYCtrl LC3                lc   cpld2       0.08        0.00      0.1  
                     LCClkCtrl LC3              lc   cpld3       0.03        0.00      0.1  
                     CPUCtrl LC3                lc   cpld4       1.03        0.00      0.1  
                     PortCtrl LC3               lc   fpga2       0.11        0.00      0.1  
                     Raven LC3                  lc   fpga1       1.03        0.00      0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-16T/8-L          Can Bus Ctrl (CBC) LC3     lc   cbc         6.08        0.00      0.1  
                     CPUCtrl LC3                lc   cpld1       1.02        0.00      0.1  
                     PHYCtrl LC3                lc   cpld2       0.04        0.00      0.1  
                     LCClkCtrl LC3              lc   cpld3       0.01        0.00      0.1  
                     DB CPUCtrl LC3             lc   cpld4       1.03        0.00      0.1  
                     PortCtrl LC3               lc   fpga2       0.01        0.00      0.1  
                     Raven LC3                  lc   fpga1       1.03        0.00      0.1  
                     ROMMONB LC3                lc   rommon      1.03        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-SIP-700          Can Bus Ctrl (CBC) LC5     lc   cbc         3.06        0.00      0.1  
                     CPUCtrl LC5                lc   cpld1       0.15        0.00      0.1  
                     QFPCPUBridge LC5           lc   fpga2       5.14        0.00      0.1  
                     NPUXBarBridge LC5          lc   fpga1       0.23        0.00      0.1  
                     ROMMONB LC5                lc   rommon      1.04        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-SIP-500          Can Bus Ctrl (CBC) LC5     lc   cbc         3.06        0.00      0.1  
                     CPUCtrl LC5                lc   cpld1       0.15        0.00      0.1  
                     QFPCPUBridge LC5           lc   fpga2       5.14        0.00      0.1  
                     NPUXBarBridge LC5          lc   fpga1       0.23        0.00      0.1  
                     ROMMONB LC5                lc   rommon      1.04        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-SIP-700-8G       Can Bus Ctrl (CBC) LC5     lc   cbc         3.06        0.00      0.1  
                     CPUCtrl LC5                lc   cpld1       0.15        0.00      0.1  
                     QFPCPUBridge LC5           lc   fpga2       5.14        0.00      0.1  
                     NPUXBarBridge LC5          lc   fpga1       0.23        0.00      0.1  
                     ROMMONB LC5                lc   rommon      1.35        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-RSP-2G           Can Bus Ctrl (CBC) RSP2    lc   cbc         1.03        0.00      0.1  
                     CPUCtrl RSP2               lc   cpld2       1.18        0.00      0.1  
                     IntCtrl RSP2               lc   fpga2       1.15        0.00      0.1  
                     ClkCtrl RSP2               lc   fpga3       1.23        0.00      0.1  
                     UTI RSP2                   lc   fpga4       3.08        0.00      0.1  
                     PUNT RSP2                  lc   fpga1       1.05        0.00      0.1  
                     ROMMONB RSP2               lc   rommon      1.06        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-RSP-4G           Can Bus Ctrl (CBC) RSP2    lc   cbc         1.03        0.00      0.1  
                     CPUCtrl RSP2               lc   cpld2       1.18        0.00      0.1  
                     IntCtrl RSP2               lc   fpga2       1.15        0.00      0.1  
                     ClkCtrl RSP2               lc   fpga3       1.23        0.00      0.1  
                     UTI RSP2                   lc   fpga4       3.08        0.00      0.1  
                     PUNT RSP2                  lc   fpga1       1.05        0.00      0.1  
                     ROMMONB RSP2               lc   rommon      1.06        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-RSP-8G           Can Bus Ctrl (CBC) RSP2    lc   cbc         1.03        0.00      0.1  
                     CPUCtrl RSP2               lc   cpld2       1.18        0.00      0.1  
                     IntCtrl RSP2               lc   fpga2       1.15        0.00      0.1  
                     ClkCtrl RSP2               lc   fpga3       1.23        0.00      0.1  
                     UTI RSP2                   lc   fpga4       3.08        0.00      0.1  
                     PUNT RSP2                  lc   fpga1       1.05        0.00      0.1  
                     ROMMONB RSP2               lc   rommon      1.06        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-RSP440-TR        Can Bus Ctrl (CBC) RSP3    lc   cbc        16.115       0.00      0.1  
                     ClockCtrl0 RSP3            lc   fpga2       1.06        0.00      0.1  
                     UTI RSP3                   lc   fpga3       4.09        0.00      0.1  
                     CPUCtrl RSP3               lc   fpga1       0.09        0.00      0.1  
                     ROMMONB RSP3               lc   rommon      0.70        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-RSP440-SE        Can Bus Ctrl (CBC) RSP3    lc   cbc        16.115       0.00      0.1  
                     ClockCtrl0 RSP3            lc   fpga2       1.06        0.00      0.1  
                     UTI RSP3                   lc   fpga3       4.09        0.00      0.1  
                     CPUCtrl RSP3               lc   fpga1       0.09        0.00      0.1  
                     ROMMONB RSP3               lc   rommon      0.70        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9922-RP-TR       Can Bus Ctrl (CBC) MTRP    lc   cbc        25.02        0.00      0.1  
                     Fabric Ctrl3 MTFC          lc   fpga10      1.01        0.00      0.1  
                     Fabric Ctrl4 MTFC          lc   fpga11      1.01        0.00      0.1  
                     Fabric Ctrl5 MTFC          lc   fpga12      1.01        0.00      0.1  
                     Fabric Ctrl6 MTFC          lc   fpga13      1.01        0.00      0.1  
                     CPUCtrl1                   lc   fpga2       1.03        0.00      0.1  
                     ClkCtrl                    lc   fpga3       1.03        0.00      0.1  
                     IntCtrl                    lc   fpga4       1.03        0.00      0.1  
                     UTI                        lc   fpga5       4.09        0.00      0.1  
                     Timex                      lc   fpga6       0.02        0.00      0.1  
                     Fabric Ctrl0 MTFC          lc   fpga7       1.01        0.00      0.1  
                     Fabric Ctrl1 MTFC          lc   fpga8       1.01        0.00      0.1  
                     Fabric Ctrl2 MTFC          lc   fpga9       1.01        0.00      0.1  
                     CPUCtrl0                   lc   fpga1       1.04        0.00      0.1  
                     ROMMONB MTRP               lc   rommon      5.10        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9922-RP-SE       Can Bus Ctrl (CBC) MTRP    lc   cbc        25.02        0.00      0.1  
                     Fabric Ctrl3 MTFC          lc   fpga10      1.01        0.00      0.1  
                     Fabric Ctrl4 MTFC          lc   fpga11      1.01        0.00      0.1  
                     Fabric Ctrl5 MTFC          lc   fpga12      1.01        0.00      0.1  
                     Fabric Ctrl6 MTFC          lc   fpga13      1.01        0.00      0.1  
                     CPUCtrl1                   lc   fpga2       1.03        0.00      0.1  
                     ClkCtrl                    lc   fpga3       1.03        0.00      0.1  
                     IntCtrl                    lc   fpga4       1.03        0.00      0.1  
                     UTI                        lc   fpga5       4.09        0.00      0.1  
                     Timex                      lc   fpga6       0.02        0.00      0.1  
                     Fabric Ctrl0 MTFC          lc   fpga7       1.01        0.00      0.1  
                     Fabric Ctrl1 MTFC          lc   fpga8       1.01        0.00      0.1  
                     Fabric Ctrl2 MTFC          lc   fpga9       1.01        0.00      0.1  
                     CPUCtrl0                   lc   fpga1       1.04        0.00      0.1  
                     ROMMONB MTRP               lc   rommon      5.10        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9900-RP-TR       Can Bus Ctrl (CBC) MTRP    lc   cbc        25.02        0.00      0.1  
                     Fabric Ctrl3 MTFC          lc   fpga10      1.01        0.00      0.1  
                     Fabric Ctrl4 MTFC          lc   fpga11      1.01        0.00      0.1  
                     Fabric Ctrl5 MTFC          lc   fpga12      1.01        0.00      0.1  
                     Fabric Ctrl6 MTFC          lc   fpga13      1.01        0.00      0.1  
                     CPUCtrl1                   lc   fpga2       1.03        0.00      0.1  
                     ClkCtrl                    lc   fpga3       1.03        0.00      0.1  
                     IntCtrl                    lc   fpga4       1.03        0.00      0.1  
                     UTI                        lc   fpga5       4.09        0.00      0.1  
                     Timex                      lc   fpga6       0.02        0.00      0.1  
                     Fabric Ctrl0 MTFC          lc   fpga7       1.01        0.00      0.1  
                     Fabric Ctrl1 MTFC          lc   fpga8       1.01        0.00      0.1  
                     Fabric Ctrl2 MTFC          lc   fpga9       1.01        0.00      0.1  
                     CPUCtrl0                   lc   fpga1       1.04        0.00      0.1  
                     ROMMONB MTRP               lc   rommon      5.10        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR-9900-RP-SE       Can Bus Ctrl (CBC) MTRP    lc   cbc        25.02        0.00      0.1  
                     Fabric Ctrl3 MTFC          lc   fpga10      1.01        0.00      0.1  
                     Fabric Ctrl4 MTFC          lc   fpga11      1.01        0.00      0.1  
                     Fabric Ctrl5 MTFC          lc   fpga12      1.01        0.00      0.1  
                     Fabric Ctrl6 MTFC          lc   fpga13      1.01        0.00      0.1  
                     CPUCtrl1                   lc   fpga2       1.03        0.00      0.1  
                     ClkCtrl                    lc   fpga3       1.03        0.00      0.1  
                     IntCtrl                    lc   fpga4       1.03        0.00      0.1  
                     UTI                        lc   fpga5       4.09        0.00      0.1  
                     Timex                      lc   fpga6       0.02        0.00      0.1  
                     Fabric Ctrl0 MTFC          lc   fpga7       1.01        0.00      0.1  
                     Fabric Ctrl1 MTFC          lc   fpga8       1.01        0.00      0.1  
                     Fabric Ctrl2 MTFC          lc   fpga9       1.01        0.00      0.1  
                     CPUCtrl0                   lc   fpga1       1.04        0.00      0.1  
                     ROMMONB MTRP               lc   rommon      5.10        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR9001-RP           Can Bus Ctrl (CBC) IMRP    lc   cbc        22.114       0.00      0.1  
                     MB CPUCtrl                 lc   fpga2       1.14        0.00      0.0  
                     ROMMONB IM RP              lc   rommon      1.36        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-24x10GE-SE       Can Bus Ctrl (CBC) LC6     lc   cbc        19.109       0.00      0.0  
                     DBCtrl LC6                 lc   fpga2       1.03        0.00      0.0  
                     LinkCtrl LC6               lc   fpga3       1.01        0.00      0.0  
                     LCCPUCtrl LC6              lc   fpga4       1.07        0.00      0.0  
                     ROMMONB LC6                lc   rommon      1.29        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-2x100GE-SE       Can Bus Ctrl (CBC) LC4     lc   cbc        21.108       0.00      0.1  
                     DB IO FPGA1                lc   cpld1       1.03        0.00      0.0  
                     MB CPUCtrl                 lc   fpga2       1.08        0.00      0.0  
                     PortCtrl                   lc   fpga3       1.05        0.00      0.0  
                     Imux                       lc   fpga4       1.01        0.00      0.0  
                     Emux                       lc   fpga5       1.03        0.00      0.0  
                     100GIGMAC                  lc   fpga6      38.00        0.00      0.0  
                     ROMMONB LC4                lc   rommon      1.29        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-MOD80-SE         Can Bus Ctrl (CBC) LC4     lc   cbc        20.115       0.00      0.1  
                     DB Ctrl                    lc   fpga2       1.04        0.00      0.0  
                     MB CPUCtrl                 lc   fpga4       1.05        0.00      0.0  
                     ROMMONB LC4                lc   rommon      1.29        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-MOD160-SE        Can Bus Ctrl (CBC) LC4     lc   cbc        20.115       0.00      0.1  
                     DB Ctrl                    lc   fpga2       1.04        0.00      0.0  
                     MB CPUCtrl                 lc   fpga4       1.05        0.00      0.0  
                     ROMMONB LC4                lc   rommon      1.29        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-24x10GE-TR       Can Bus Ctrl (CBC) LC6     lc   cbc        19.109       0.00      0.0  
                     DBCtrl LC6                 lc   fpga2       1.03        0.00      0.0  
                     LinkCtrl LC6               lc   fpga3       1.01        0.00      0.0  
                     LCCPUCtrl LC6              lc   fpga4       1.07        0.00      0.0  
                     ROMMONB LC6                lc   rommon      1.29        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-2x100GE-TR       Can Bus Ctrl (CBC) LC4     lc   cbc        21.108       0.00      0.1  
                     DB IO FPGA1                lc   cpld1       1.03        0.00      0.0  
                     MB CPUCtrl                 lc   fpga2       1.08        0.00      0.0  
                     PortCtrl                   lc   fpga3       1.05        0.00      0.0  
                     Imux                       lc   fpga4       1.01        0.00      0.0  
                     Emux                       lc   fpga5       1.03        0.00      0.0  
                     100GIGMAC                  lc   fpga6      38.00        0.00      0.0  
                     ROMMONB LC4                lc   rommon      1.29        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-MOD80-TR         Can Bus Ctrl (CBC) LC4     lc   cbc        20.115       0.00      0.1  
                     DB Ctrl                    lc   fpga2       1.04        0.00      0.0  
                     MB CPUCtrl                 lc   fpga4       1.05        0.00      0.0  
                     ROMMONB LC4                lc   rommon      1.29        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-MOD160-TR        Can Bus Ctrl (CBC) LC4     lc   cbc        20.115       0.00      0.1  
                     DB Ctrl                    lc   fpga2       1.04        0.00      0.0  
                     MB CPUCtrl                 lc   fpga4       1.05        0.00      0.0  
                     ROMMONB LC4                lc   rommon      1.29        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-8T-TEST          Can Bus Ctrl (CBC) LC17    lc   cbc        17.214       0.00      0.0  
                     LCCPUCtrl LC6              lc   fpga4       0.03        0.00      0.0  
                     ROMMONB LC6                lc   rommon      1.04        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-36x10GE-SE       Can Bus Ctrl (CBC) LC6     lc   cbc        15.101       0.00      0.0  
                     DBCtrl LC6                 lc   fpga2       1.01        0.00      0.0  
                     LinkCtrl LC6               lc   fpga3       1.00        0.00      0.0  
                     LCCPUCtrl LC6              lc   fpga4       1.03        0.00      0.0  
                     ROMMONB LC6                lc   rommon      1.29        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-36x10GE-TR       Can Bus Ctrl (CBC) LC6     lc   cbc        15.101       0.00      0.0  
                     DBCtrl LC6                 lc   fpga2       1.01        0.00      0.0  
                     LinkCtrl LC6               lc   fpga3       1.00        0.00      0.0  
                     LCCPUCtrl LC6              lc   fpga4       1.03        0.00      0.0  
                     ROMMONB LC6                lc   rommon      1.29        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-1x100GE-SE       Can Bus Ctrl (CBC) LC4     lc   cbc        21.108       0.00      0.1  
                     DB IO FPGA1                lc   cpld1       1.03        0.00      0.0  
                     MB CPUCtrl                 lc   fpga2       1.08        0.00      0.0  
                     PortCtrl                   lc   fpga3       1.05        0.00      0.0  
                     Imux                       lc   fpga4       1.01        0.00      0.0  
                     Emux                       lc   fpga5       1.03        0.00      0.0  
                     100GIGMAC                  lc   fpga6      38.00        0.00      0.0  
                     ROMMONB LC4                lc   rommon      1.29        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-1x100GE-TR       Can Bus Ctrl (CBC) LC4     lc   cbc        21.108       0.00      0.1  
                     DB IO FPGA1                lc   cpld1       1.03        0.00      0.0  
                     MB CPUCtrl                 lc   fpga2       1.08        0.00      0.0  
                     PortCtrl                   lc   fpga3       1.05        0.00      0.0  
                     Imux                       lc   fpga4       1.01        0.00      0.0  
                     Emux                       lc   fpga5       1.03        0.00      0.0  
                     100GIGMAC                  lc   fpga6      38.00        0.00      0.0  
                     ROMMONB LC4                lc   rommon      1.29        0.00      0.0  
----------------------------------------------------------------------------------------------
ASR9001-LC           Can Bus Ctrl (CBC) IMLC    lc   cbc        23.114       0.00      0.1  
                     DB CPUCtrl                 lc   fpga2       1.17        0.00      0.0  
                     EP Gambit                  lc   fpga3       0.08        0.00      0.0  
                     MB CPUCtrl                 lc   fpga4       2.07        0.00      0.0  
                     EP Rogue                   lc   fpga6       1.06        0.00      0.0  
                     EP Sage                    lc   fpga7       1.02        0.00      0.0  
                     ROMMONB IM LC              lc   rommon      1.36        0.00      0.1  
----------------------------------------------------------------------------------------------
ASR9001-LC-S         Can Bus Ctrl (CBC) IMLC    lc   cbc        23.114       0.00      0.1  
                     DB CPUCtrl                 lc   fpga2       1.17        0.00      0.0  
                     EP Gambit                  lc   fpga3       0.08        0.00      0.0  
                     MB CPUCtrl                 lc   fpga4       2.07        0.00      0.0  
                     EP Rogue                   lc   fpga6       1.06        0.00      0.0  
                     EP Sage                    lc   fpga7       1.02        0.00      0.0  
                     ROMMONB IM LC              lc   rommon      1.36        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-ISM-100          Can Bus Ctrl (CBC) LC6     lc   cbc        18.06        0.00      0.1  
                     CPUCtrl LC6                lc   cpld1       0.01        0.00      0.1  
                     Maintenance LC6            lc   fpga2       2.13        0.00      0.1  
                     Amistad LC6                lc   fpga1       0.33        0.00      0.20 
                     ROMMONB LC6                lc   rommon      1.02        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-RSP-3G           ClockCtrl0 RSP3            lc   fpga2       1.06        0.00      0.1  
                     UTI RSP3                   lc   fpga3       4.09        0.00      0.1  
                     CPUCtrl RSP3               lc   fpga1       0.09        0.00      0.1  
                     ROMMONB RSP3               lc   rommon      0.70        0.00      0.1  
----------------------------------------------------------------------------------------------
A9K-RSP-24G          ClockCtrl0 RSP3            lc   fpga2       1.06        0.00      0.1  
                     UTI RSP3                   lc   fpga3       4.09        0.00      0.1  
                     CPUCtrl RSP3               lc   fpga1       0.09        0.00      0.1  
                     ROMMONB RSP3               lc   rommon      0.70        0.00      0.1  
----------------------------------------------------------------------------------------------
SPA-4XT3/E3          SPA E3 Subrate FPGA        spa  fpga2       1.04        0.00      0.0  
                     SPA T3 Subrate FPGA        spa  fpga3       1.04        0.00      0.0  
                     SPA I/O FPGA               spa  fpga1       1.01        0.00      0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-4XCT3/DS0        SPA T3 Subrate FPGA        spa  fpga2       0.11        0.00      0.100
                     SPA T3 Subrate FPGA        spa  fpga2       1.04        0.00      0.200
                     SPA I/O FPGA               spa  fpga1       2.08        0.00      0.100
                     SPA ROMMON                 spa  rommon      2.12        0.00      0.100
----------------------------------------------------------------------------------------------
SPA-1XCHSTM1/OC3     SPA T3 Subrate FPGA        spa  fpga2       1.04        0.00      0.0  
                     SPA I/O FPGA               spa  fpga1       1.08        0.00      0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-24CHT1-CE-ATM    SPA T3 Subrate FPGA        spa  fpga2       1.10        0.00      1.0  
                     SPA I/O FPGA               spa  fpga1       2.32        0.00      1.0  
                     SPA ROMMON                 spa  rommon      1.03        0.00      1.0  
----------------------------------------------------------------------------------------------
SPA-2CHT3-CE-ATM     SPA T3 Subrate FPGA        spa  fpga2       1.11        0.00      1.0  
                     SPA I/O FPGA               spa  fpga1       2.22        0.00      1.0  
                     SPA ROMMON                 spa  rommon      1.04        0.00      1.0  
----------------------------------------------------------------------------------------------
SPA-1CHOC3-CE-ATM    SPA OC3 Subrate FPGA       spa  fpga2       2.23        0.00      0.0  
                     SPA I/O FPGA               spa  fpga1       2.23        0.00      2.0  
                     SPA ROMMON                 spa  rommon      1.04        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-1XCHOC48/DS3     SPA I/O FPGA               spa  fpga2       1.00        0.00      0.49 
                     SPA I/O FPGA               spa  fpga3       1.00        0.00      0.52 
                     SPA I/O FPGA               spa  fpga1       1.36        0.00      0.49 
                     SPA ROMMON                 spa  rommon      2.02        0.00      0.49 
----------------------------------------------------------------------------------------------
SPA-2XCHOC12/DS0     SPA FPGA2 swv1.00          spa  fpga2       1.00        0.00      0.0  
                     SPA FPGA swv1.36           spa  fpga1       1.36        0.00      0.49 
                     SPA ROMMON swv2.2          spa  rommon      2.02        0.00      0.49 
----------------------------------------------------------------------------------------------
A9K-MPA-20X1GE       EP I/O FPGA                spa  fpga3       0.08        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-MPA-2X10GE       EP I/O FPGA                spa  fpga6       1.06        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-MPA-4X10GE       EP I/O FPGA                spa  fpga6       1.06        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-MPA-2X40GE       EP Sage                    spa  fpga7       1.03        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-MPA-1X40GE       EP Sage                    spa  fpga7       1.03        0.00      0.0  
----------------------------------------------------------------------------------------------
A9K-MPA-8X10GE       EP I/O FPGA                spa  fpga8       0.07        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-8XOC12-POS       SPA FPGA swv1.0            spa  fpga1       1.00        0.00      0.5  
----------------------------------------------------------------------------------------------
SPA-8XCHT1/E1        SPA I/O FPGA               spa  fpga1       2.08        0.00      0.0  
                     SPA ROMMON                 spa  rommon      2.12        0.00      0.140
----------------------------------------------------------------------------------------------
SPA-OC192POS-XFP     SPA FPGA swv1.2 hwv2       spa  fpga1       1.02        0.00      2.0  
----------------------------------------------------------------------------------------------
SPA-2XOC48POS/RPR    SPA FPGA swv1.0            spa  fpga1       1.00        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-4XOC48POS/RPR    SPA FPGA swv1.0            spa  fpga1       1.00        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-8XOC3-POS        SPA FPGA swv1.0            spa  fpga1       1.00        0.00      0.5  
----------------------------------------------------------------------------------------------
SPA-2XOC12-POS       SPA FPGA swv1.0            spa  fpga1       1.00        0.00      0.5  
----------------------------------------------------------------------------------------------
SPA-4XOC12-POS       SPA FPGA swv1.0            spa  fpga1       1.00        0.00      0.5  
----------------------------------------------------------------------------------------------
SPA-10X1GE-V2        SPA FPGA swv1.10           spa  fpga1       1.10        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-5X1GE-V2         SPA FPGA swv1.10           spa  fpga1       1.10        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-1X10GE-L-V2      SPA FPGA swv1.9            spa  fpga1       1.09        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-4XOC3-POS-V2     SPA FPGA swv1.0            spa  fpga1       1.00        0.00      0.5  
----------------------------------------------------------------------------------------------
SPA-1X10GE-WL-V2     SPA FPGA swv1.9            spa  fpga1       1.09        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-1XOC3-ATM-V2     SPA FPGA swv1.2            spa  fpga1       2.02        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-2XOC3-ATM-V2     SPA FPGA swv1.2            spa  fpga1       2.02        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-3XOC3-ATM-V2     SPA FPGA swv1.2            spa  fpga1       2.02        0.00      0.0  
----------------------------------------------------------------------------------------------
SPA-1XOC12-ATM-V2    SPA FPGA swv1.2            spa  fpga1       2.02        0.00      0.0  
----------------------------------------------------------------------------------------------

Note


In the show fpd package command output, the “subtype” column shows the FPDs that correspond with each SPA image. To upgrade a specific FPD with the upgrade hw-module fpd command, replace the fpga-type argument with the appropriate FPD from the “subtype” column, as shown in the following example:

RP/0/0RP0RSP0/CPU0:router(admin)# upgrade hw-module fpd fpga2 location 0/3/1 reload


Related Commands

Command

Description

show hw-module fpd

Displays field-programmable device (FPD) compatibility for all modules or a specific module.

upgrade hw-module fpd

Manually upgrades the current field-programmable device (FPD) image package on a module.

show hw-module fpd

To display field-programmable device (FPD) compatibility for all modules or a specific module, use the show hw-module fpd command in the EXEC or administration EXE mode.

show hw-module fpd location { node-id | all }

Syntax Description

location{node-id | all}

Specifies the location of the module. The node-id argument is expressed in the rack/slot/module notation. Use the all keyword to indicate all nodes.

Command Default

No default behavior or values

Command Modes

EXEC

System Admin EXEC

XR EXEC

Administration EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Release 5.0.0

This command was introduced.

Release 3.4.0

The show hw-module fpd command output was updated to display the ROMMON images.

Release 3.7.2

This command was introduced.

Release 3.9.0

Support was added for the 2-port channelized OC-12/DS0 SPA.

Release 4.3.2

Support for Back-plane identification (BPID) nodes.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

sysmgr

read

root-lr

read

Examples

The following example shows how to display FPD compatibility for all modules in the router:

RP/0/RP0/CPU0:router# show hw-module fpd location all
  
===================================== ==========================================
                                      Existing Field Programmable Devices
                                      ==========================================
                                        HW                       Current SW Upg/
Location     Card Type                Version Type Subtype Inst   Version   Dng?
============ ======================== ======= ==== ======= ==== =========== ====
0/1/CPU0     CRS1-SIP-800               0.96  lc   fpga    0       2.0      No
--------------------------------------------------------------------------------
0/1/0        SPA-4XOC3-POS              1.0   spa  fpga    0       3.4      No
--------------------------------------------------------------------------------
0/1/5        SPA-8X1GE                  2.2   spa  fpga    5       1.8      No
--------------------------------------------------------------------------------
0/6/CPU0     CRS1-SIP-800               0.96  lc   fpga    0       2.0      No
--------------------------------------------------------------------------------
0/6/0        SPA-4XOC3-POS              1.0   spa  fpga    0       3.4      No
--------------------------------------------------------------------------------
0/6/4        SPA-8XOC3-OC12-POS         1.1   spa  fpga    4       0.5      Yes
--------------------------------------------------------------------------------
0/6/5        SPA-8X1GE                  2.2   spa  fpga    5       1.8      No
--------------------------------------------------------------------------------
NOTES:
1.  One or more FPD needs an upgrade or a downgrade.  This can be accomplished
    using the "admin upgrade hw-module fpd" CLI.
  
RP/0/0/CPU0:router# show hw-module fpd location all

===================================== ==========================================
                                      Existing Field Programmable Devices
                                      ==========================================
                                        HW                       Current SW Upg/
Location     Card Type                Version Type Subtype Inst   Version   Dng?
============ ======================== ======= ==== ======= ==== =========== ====
0/1/0        SPA-4XT3/E3                1.0   spa  fpga    0       0.24     No 
                                              spa  rommon  0       2.12     No 
                                              spa  fpga2   0       1.0      No 
                                              spa  fpga3   0       1.0      No 
--------------------------------------------------------------------------------
0/1/1        SPA-4XCT3/DS0              0.253 spa  fpga    1       2.1      No 
                                              spa  rommon  1       2.12     No 
                                              spa  fpga2   1       0.15     No 
--------------------------------------------------------------------------------
0/3/0        SPA-2XOC48POS/RPR          1.0   spa  fpga    0       1.0      No 
--------------------------------------------------------------------------------
0/3/1        SPA-1XTENGE-XFP            3.2   spa  fpga    1       1.7      No 
--------------------------------------------------------------------------------
  
RP/0/RSP1/CPU0:router# show hw-module fpd location all 

Mon Jun 29 05:38:50.332 PST

===================================== ==========================================
                                      Existing Field Programmable Devices
                                      ==========================================
                                        HW                       Current SW Upg/
Location     Card Type                Version Type Subtype Inst   Version   Dng?
============ ======================== ======= ==== ======= ==== =========== ====
0/RSP0/CPU0  A9K-RSP-4G                 4.8   lc   fpga3   0       1.13     No 
                                              lc   fpga1   0       1.5      No 
                                              lc   fpga2   0       1.14     No 
                                              lc   cbc     0       1.2      No 
                                              lc   fpga4   0       1.6      No 
                                              lc   rommon  0       1.0      No 
--------------------------------------------------------------------------------
0/RSP0/CPU0  ASR-9010-FAN               1.0   lc   cbc     1       4.0      No 
--------------------------------------------------------------------------------
0/RSP0/CPU0  ASR-9010-FAN               1.0   lc   cbc     2       4.0      No 
--------------------------------------------------------------------------------
0/1/CPU0     A9K-40GE-B                 1.0   lc   fpga1   0       0.38     No 
                                              lc   fpga2   0       0.8      No 
                                              lc   cbc     0       2.2      No 
                                              lc   cpld1   0       0.15     No 
                                              lc   rommon  0       1.0      No 
--------------------------------------------------------------------------------
0/1/CPU0     A9K-40GE-B                 1.0   lc   fpga1   1       0.38     No 
--------------------------------------------------------------------------------
0/4/CPU0     A9K-8T/4-B                 1.0   lc   fpga1   0       0.38     No 
                                              lc   fpga2   0       0.10     No 
                                              lc   cbc     0       2.2      No 
                                              lc   cpld2   0       0.7      No 
                                              lc   cpld1   0       0.15     No 
                                              lc   cpld3   0       0.3      No 
                                              lc   rommon  0       1.0      No 
                                              lc   fpga3   0      14.42     No 
--------------------------------------------------------------------------------
0/4/CPU0     A9K-8T/4-B                 1.0   lc   fpga1   1       0.38     No 
--------------------------------------------------------------------------------
0/6/CPU0     A9K-4T-B                   1.0   lc   fpga1   0       0.38     No 
                                              lc   fpga2   0       0.10     No 
                                              lc   cbc     0       2.2      No 
                                              lc   cpld2   0       0.7      No 
                                              lc   cpld1   0       0.15     No 
                                              lc   cpld3   0       0.3      No 
                                              lc   rommon  0       1.0      No 
                                              lc   fpga3   0      14.42     No 
--------------------------------------------------------------------------------
0/6/CPU0     A9K-4T-B                   1.0   lc   fpga1   1       0.38     No 
--------------------------------------------------------------------------------
  

BPID nodes can be used as location to display the BPID image information:

RP/0/0RP0RSP0/CPU0:router# sh hw-module fpd location 0/bpid0/sp


===================================== ==========================================
                                      Existing Field Programmable Devices
                                      ==========================================
                                        HW                       Current SW Upg/
Location     Card Type                Version Type Subtype Inst   Version   Dng?
============ ======================== ======= ==== ======= ==== =========== ====
0/BPID0/SP   ASR-9912-BPID2             1.0   bp   cbc     11      7.104    No

The following example shows how to display FPD compatibility for a specific module in the router:

RP/0/RP0/CPU0:router# show hw-module fpd location 0/6/cpu0

Sun Apr 18 03:18:24.903 DST

===================================== ==========================================
                                      Existing Field Programmable Devices
                                      ==========================================
                                        HW                       Current SW Upg/
Location     Card Type                Version Type Subtype Inst   Version   Dng?
============ ======================== ======= ==== ======= ==== =========== ====
0/6/CPU0     CRS1-SIP-800               0.96  lc   fpga1   0       6.00     No
                                              lc   rommonA 0       2.100    No
                                              lc   rommon  0       2.100    No
--------------------------------------------------------------------------------
  
RP/0/0/CPU0:router# show hw-module fpd location 0/1/0
Sun Apr 18 10:51:33.776 DST

===================================== ==========================================
                                      Existing Field Programmable Devices
                                      ==========================================
                                        HW                       Current SW Upg/
Location     Card Type                Version Type Subtype Inst   Version   Dng?
============ ======================== ======= ==== ======= ==== =========== ====
0/1/0        SPA-1XTENGE-XFP            3.2   spa  fpga1   0       1.09     No
--------------------------------------------------------------------------------
  
RP/0/RSP1/CPU0:router# show hw-module fpd location 0/4/cpu0 

Thu Nov 19 21:43:49.599 UTC
===================================== ==========================================
                                      Existing Field Programmable Devices
                                      ==========================================
                                        HW                       Current SW Upg/
Location     Card Type                Version Type Subtype Inst   Version   Dng?
============ ======================== ======= ==== ======= ==== =========== ====
0/4/CPU0     A9K-SIP-700                1.13  lc   fpga1   0       0.22     No 
                                              lc   cbc     0       3.03     No 
                                              lc   hsbi    0       3.00     No 
                                              lc   rommon  0       1.02     No 
                                              lc   fpga2   0       5.14     No 
                                              lc   cpld1   0       0.14     No 
--------------------------------------------------------------------------------
  

If the cards in the system do not meet the minimum requirements, the output contains a “NOTES” section that states how to upgrade the FPD image.

Table 6 show hw-module fpd Field Descriptions

Field

Description

Location

Location of the module in the rack/slot/module notation.

Card Type

Module part number.

HW Version

Hardware model version for the module.

Type

Hardware type. Can be one of the following types:

  • spa—Shared port adapter
  • lc—Line card

Subtype

FPD type. Can be one of the following types:

  • fabldr—Fabric downloader
  • fpga1—Field-programmable gate array
  • fpga2—Field-programmable gate array 2
  • fpga3—Field-programmable gate array 3
  • fpga4—Field-programmable gate array 4
  • fpga5—Field-programmable gate array 5
  • rommonA—Read-only memory monitor A
  • rommon—Read-only memory monitor B

Inst

FPD instance. The FPD instance uniquely identifies an FPD and is used by the FPD process to register an FPD.

Current SW Version

Currently running FPD image version.

Upg/Dng?

Specifies whether an FPD upgrade or downgrade is required. A downgrade is required in rare cases when the version of the FPD image has a higher major revision than the version of the FPD image in the current Cisco IOS XR software package.


Related Commands

Command

Description

show fpd package

Displays which SPAs and SIPs are supported with your current Cisco IOS XR software release, which FPD image you need for each card, and what the minimum hardware requirements are for the various modules.

upgrade hw-module fpd

Manually upgrades the current field-programmable device (FPD) image package on a module.

show hw-module profile

To display the active profiles on the router, use the show hw-module profile command in EXEC mode.

show hw-module profile feature { all | location node-id }

show hw-module profile { all | feature | scale } [ location node-id ]

Syntax Description

all

Displays information regarding all active profiles.

feature

Displays information regarding active feature profiles.

scale

Displays information regarding active scale profiles.

location node-id

Displays the active profile for a particular node.

Command Modes

EXEC

Command History

Release Modification

Release 3.9.1

This command was introduced.

Release 4.0.1

The feature keyword was added.

Release 4.2.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The show hw-module profile command displays only active profiles. If a profile has been configured and the line card has not be reloaded since the configuration, the profile is not active. Use the show running-config hw-module profile command to view configured profiles.

Task ID

Task ID Operation

root-lr

read

Examples

This example shows sample output from the show hw-module profiles command with the feature keyword:

RP/0/RSP0/CPU0router0# show hw-module profile feature

Thu Dec  9 03:30:42.633 PST

                Node: 0/0/CPU0:
----------------------------------------------------------------

Memory Resources for All NPs
----------------------------
Feature Profile: Default

                Node: 0/1/CPU0:
----------------------------------------------------------------

Memory Resources for All NPs
----------------------------
Feature Profile: Default

                Node: 0/4/CPU0:
----------------------------------------------------------------

Memory Resources for All NPs
----------------------------
Feature Profile: Default

                Node: 0/6/CPU0:
----------------------------------------------------------------

Memory Resources for All NPs
----------------------------
Feature Profile: Default
  
RP/0/0RP0RSP0/CPU0:router# show hw-module profile feature all

Thu Sep  8 22:38:50.973 DST
----------------------------------------
BundleName      Features Not Supported
----------------------------------------
Default         iMSG
iMsg            Biscuit
----------------------------------------
Nodeno          Active Bundle Name
----------------------------------------
0               Not Supported
1               Default
2               Default
3               Default
4               Default
----------------------------------------
  

Related Commands

Command

Description

hw-module profile feature

Enables a feature bundle on the router.  

hw-module profile scale

Specifies a scale profile for the router.  


Related Commands

Command

Description

hw-module profile feature

Enables a feature bundle on the router.

hw-module profile scale

Specifies a scale profile for the router.

show hw-module subslot brief

To display summary information related to a specified internal hardware device on a shared port adapter (SPA), use the show hw-module subslot brief command in

EXEC

XR EXEC

mode.

show hw-module subslot [node-id] brief [ device [ device-index [device-subindex] ] ]

Syntax Description

node-id

(Optional) Location for which to display the specified information. The node-id argument is entered in the rack/slot/module notation.

device

(Optional) Internal hardware device for which to display the specified information. Valid devices include:

  • analog-digital-converter—Displays analog-to-digital converter information.

  • c2w—Displays Cisco-to-wire bus device information.

  • fpga—Displays SPA field-programmable gate array information.

  • framer—Displays SONET framer information. (Not applicable to Ethernet SPAs.)

  • hdlc—Displays SPA hdlc information, where applicable.

  • l2-tcam—Displays SPA Layer 2 ternary content addressable memory information. (Not applicable to POS SPAs.)

  • mac—Displays SPA MAC information. (Not applicable to POS SPAs.)

  • pluggable-optics—Displays pluggable-optics module information.

  • power-margining—Displays power-margining device information.

  • sar—Displays SPA ATM SAR information.

  • sdcc—Displays section data communications channel device information. (Not applicable to Ethernet SPAs.)

  • serdes—Displays SPA serializer/deserializer information.

  • spi4—Displays system packet interface level 4.2 bus device information.

  • temperature-sensor—Displays temperature sensor information.

device-index

(Optional) Index of the specific device if there are multiple devices of the same type.

device-subindex

(Optional) Subindex of the specific device if there are multiple devices of the same device index.

Command Default

No default behavior or values

Command Modes

EXEC

XR EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Release 5.0.0

This command was introduced.

Release 3.9.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

You can also enter a partially qualified location specifier by using the wildcard (*) character. For example, 0/1/* would display information for all modules on slot 1 in rack 0.

Use the show hw-module subslot brief command to obtain summary diagnostic information about a device on an interface on the SPA.

Task ID

Task ID

Operations

root-lr

read

Examples

The following example shows sample output for the show hw-module subslot brief command:

RP/0/0RP0RSP0/CPU0:router# show hw-module subslot 0/1/0 brief
  
  Subslot 0/1/0 brief info:
  -----------------------
  SPA inserted: YES
  SPA type:     4xOC3 POS SPA
  SPA operational state: READY
  SPA cfg admin up: YES
      
Table 7 show hw-module subslot config Field Descriptions

Field

Description

SPA inserted

Indicates if a SPA is currently detected in the subslot.

SPA type

Description of SPA including the technology type, number of ports, height of SPA (HHSPA—single height, FHSPA—double height), and optics type.

SPA operational state

Current state of the SPA module.

SPA cfg admin up

Configured state of the SPA: YES—the SPA is not shut down; NO—the SPA is shut down.

show hw-module subslot config

To display information related to configuration of the specified internal hardware device on a shared port adapter (SPA), use the show hw-module subslot config command in EXEC

XR EXEC

mode.

show hw-module subslot [node-id] config [ device [ device-index [device-subindex] ] ]

Syntax Description

node-id

(Optional) Location for which to display the specified information. The node-id argument is entered in the rack/slot/module notation.

device

(Optional) Internal hardware device for which to display the specified information. Valid devices include:

  • analog-digital-converter—Displays analog-to-digital converter information.

  • c2w—Displays Cisco-to-wire bus device information.

  • fpga—Displays SPA field-programmable gate array information.

  • framer—Displays SONET framer information. (Not applicable to Ethernet SPAs.)

  • hdlc—Displays SPA hdlc information, where applicable.

  • l2-tcam—Displays SPA Layer 2 ternary content addressable memory information. (Not applicable to POS SPAs.)

  • mac—Displays SPA MAC information. (Not applicable to POS SPAs.)

  • pluggable-optics—Displays pluggable-optics module information.

  • power-margining—Displays power-margining device information.

  • sar—Displays SPA ATM SAR information.

  • sdcc—Displays section data communications channel device information. (Not applicable to Ethernet SPAs.)

  • serdes—Displays SPA serializer/deserializer information.

  • spi4—Displays system packet interface level 4.2 bus device information.

  • temperature-sensor—Displays temperature sensor information.

device-index

(Optional) Index of the specific device if there are multiple devices of the same type.

device-subindex

(Optional) Subindex of the specific device if there are multiple devices of the same device index.

Command Default

No default behavior or values

Command Modes

EXEC

Release 5.0.0

Command History

Release

Modification

Release 3.2

This command was introduced.

Release 5.0.0

This command was introduced.

Release 3.9.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

You can also enter a partially qualified location specifier by using the wildcard (*) character. For example, 0/1/* would display information for all modules on slot 1 in rack 0.

Use the show hw-module subslot config command to obtain diagnostic information about the configuration of an interface on the SPA.

Task ID

Task ID

Operations

root-lr

read

Examples

The following example shows sample output for the show hw-module subslot config command:

RP/0/0RP0RSP0/CPU0:router# show hw-module subslot 0/6/cpu0 config

 Thu Feb 19 00:33:02.921 PST 

Subslot 0/6/0 config info:
------------------------
SPA inserted: YES
SPA cfg admin up: YES
SPA cfg power up: YES

Subslot 0/6/1 config info:
------------------------
SPA inserted: YES
SPA cfg admin up: YES
SPA cfg power up: YES

Subslot 0/6/2 config info:
------------------------
SPA inserted: NO
SPA cfg admin up: YES
SPA cfg power up: NO

Subslot 0/6/3 config info:
------------------------
SPA inserted: NO
SPA cfg admin up: YES
SPA cfg power up: NO

Subslot 0/6/4 config info:
------------------------
SPA inserted: NO
SPA cfg admin up: YES
SPA cfg power up: NO

Subslot 0/6/5 config info:
------------------------
SPA inserted: NO
SPA cfg admin up: YES
SPA cfg power up: NO
  
Table 8  show hw-module subslot config Field Descriptions

Field

Description

SPA inserted

Indicates if a SPA is currently detected in the subslot.

SPA cfg admin up

Configured state of the SPA: YES—the SPA is not shut down; NO—the SPA is shut down.

SPA cfg power up

Indicates whether the subslot is currently configured as powered or not.

Related Commands

Command

Description

show controllers

Displays the controller type and other information.

show hw-module subslot counters

To display statistics related to the processing of internal hardware devices for a shared port adapter (SPA), use the show hw-module subslot counters command in EXEC

XR EXEC

mode.

show hw-module subslot [node-id] counters [ device [ device-index [device-subindex] ] ]

Syntax Description

node-id

(Optional) Location for which to display the specified information. The node-id argument is entered in the rack/slot/module notation.

device

(Optional) Internal hardware device for which to display the specified information. Valid devices include:

  • analog-digital-converter—Displays analog-to-digital converter information.

  • c2w—Displays Cisco-to-wire bus device information.

  • fpga—Displays SPA field-programmable gate array information.

  • framer—Displays SONET framer information. (Not applicable to Ethernet SPAs.)

  • hdlc—Displays SPA hdlc information, where applicable.

  • l2-tcam—Displays SPA Layer 2 ternary content addressable memory information. (Not applicable to POS SPAs.)

  • mac—Displays SPA MAC information. (Not applicable to POS SPAs.)

  • pluggable-optics—Displays pluggable-optics module information.

  • power-margining—Displays power-margining device information.

  • sar—Displays SPA ATM SAR information.

  • sdcc—Displays section data communications channel device information. (Not applicable to Ethernet SPAs.)

  • serdes—Displays SPA serializer/deserializer information.

  • spi4—Displays system packet interface level 4.2 bus device information.

  • temperature-sensor—Displays temperature sensor information.

device-index

(Optional) Index of the specific device if there are multiple devices of the same type.

device-subindex

(Optional) Subindex of the specific device if there are multiple devices of the same device index.

Command Default

No default behavior or values

Command Modes

EXEC

XR EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Release 5.0.0

This command was introduced.

Release 3.9.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

You can also enter a partially qualified location specifier by using the wildcard (*) character. For example, 0/1/* would display information for all modules on slot 1 in rack 0.

Use the show hw-module subslot counters command to display statistics related to the processing by the specified internal hardware device.

Task ID

Task ID

Operations

root-lr

read

Examples

The following example shows sample output for the show hw-module subslot counters command:

RP/0/0RP0RSP0/CPU0:router# show hw-module subslot 0/1/cpu0 counters

Subslot 0/1/0 counts info:
------------------------
SPA inserted: YES
SPA type:     8xGE SPA
SPA operational state: READY
SPA insertion time:  Wed Jan 14 11:33:24 2009
SPA last time ready: Wed Jan 14 11:33:37 2009
SPA uptime [HH:MM:SS]: 852:54:24

Subslot 0/1/1 counts info:
------------------------
SPA inserted: YES
SPA type:     5xGE SPA
SPA operational state: READY
SPA insertion time:  Wed Jan 14 11:33:24 2009
SPA last time ready: Wed Jan 14 11:33:38 2009
SPA uptime [HH:MM:SS]: 852:54:23
 --More--
  
Table 9  show hw-module subslot counters Field Descriptions

Field

Description

SPA inserted

Indicates if a SPA is currently detected in the subslot.

SPA type

Description of SPA including the technology type, number of ports, height of SPA (HHSPA—single height, FHSPA—double height), and optics type.

SPA operational state

Current state of the SPA module.

SPA insertion time

Time the SPA module was last physically inserted or power-cycled.

SPA last time ready

Time the SPA module last changed state to up or ready (the last time the module was loaded or reloaded).

SPA uptime

The time in service or amount of time since the module was last out of service due to a reload, power cycle, or configuration event.

The following example shows sample output for the show hw-module subslot counters command with the framer keyword:

RP/0/0RP0RSP0/CPU0:router# show hw-module subslot counters framer
  
  SPA device framer index 0 subindex 0 info:
  
  Milan Framer counters:
  STREAM 0
  Rx Bytes (48-bit) (#0x381fa078-0x883c): 163857232569448
  Rx Good Bytes (48-bit) (#0x381fa080-0x8840): 1964924
  Rx Good Packets (48-bit) (#0x381fa040-0x8820): 26234
  Tx Byte Cnt Reg (48-bit) (#0x381fe070-0xa838): 9375380
  Tx Good Bytes Cnt Reg (48-bit) (#0x381fe068-0xa834): 8909442
  Tx Transmitted Packet Cnt Reg (48-bit) (#0x381fe040-0xa820): 114692
  

show hw-module subslot errors

To display error information about internal hardware devices for a shared port adapter (SPA), use the show hw-module subslot errors command in

EXEC

XR EXEC

mode.

show hw-module subslot [node-id] errors [ device [ device-index [device-subindex] ] ]

Syntax Description

node-id

(Optional) Location for which to display the specified information. The node-id argument is entered in the rack/slot/module notation.

device

(Optional) Internal hardware device for which to display the specified information. Valid devices include:

  • analog-digital-converter—Displays analog-to-digital converter information.

  • c2w—Displays Cisco-to-wire bus device information.

  • fpga—Displays SPA field-programmable gate array information.

  • framer—Displays SONET framer information. (Not applicable to Ethernet SPAs.)

  • hdlc—Displays SPA hdlc information, where applicable.

  • l2-tcam—Displays SPA Layer 2 ternary content addressable memory information. (Not applicable to POS SPAs.)

  • mac—Displays SPA MAC information. (Not applicable to POS SPAs.)

  • pluggable-optics—Displays pluggable-optics module information.

  • power-margining—Displays power-margining device information.

  • sar—Displays SPA ATM SAR information.

  • sdcc—Displays section data communications channel device information. (Not applicable to Ethernet SPAs.)

  • serdes—Displays SPA serializer/deserializer information.

  • spi4—Displays system packet interface level 4.2 bus device information.

  • temperature-sensor—Displays temperature sensor information.

device-index

(Optional) Index of the specific device if there are multiple devices of the same type.

device-subindex

(Optional) Subindex of the specific device if there are multiple devices of the same device index.

Command Default

No default behavior or values

Command Modes

EXEC

XR EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Release 5.0.0

This command was introduced.

Release 3.9.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

You can also enter a partially qualified location specifier by using the wildcard (*) character. For example, 0/1/* would display information for all modules on slot 1 in rack 0.

Use the show hw-module subslot errors command to display error information related to the specified internal hardware device on a SPA.

Task ID

Task ID

Operations

root-lr

read

Examples

The following example shows partial sample output for the show hw-module subslot errors command:

RP/0/0RP0RSP0/CPU0:router# show hw-module subslot 0/1/0 errors

Subslot 0/1/0 errors info:
  ------------------------
  SPA inserted: YES
  SPA type:     4xOC3 POS SPA
  SPA operational state: READY
  SPA last reset reason:   UNKNOWN
  SPA last failure reason: UNKNOWN
  
  Subslot 0/1/1 errors info:
  ------------------------
  SPA inserted: YES
  SPA type:     1x10GE XFP SPA
  SPA operational state: READY
  SPA last reset reason:   UNKNOWN
  SPA last failure reason: UNKNOWN
  
  Subslot 0/1/2 errors info:
  ------------------------
  SPA inserted: NO
  
  Subslot 0/1/3 errors info:
  ------------------------
  SPA inserted: NO
  
  Subslot 0/1/4 errors info:
  ------------------------
  SPA inserted: YES
  SPA type:     4xOC48 POS/RPR HHSPA
  SPA operational state: READY
  SPA last reset reason:   UNKNOWN
  SPA last failure reason: UNKNOWN
  
  Subslot 0/1/5 errors info:
  ------------------------
  SPA inserted: YES
  SPA type:     8xGE SPA
  SPA operational state: READY
  SPA last reset reason:   UNKNOWN
  SPA last failure reason: UNKNOWN
  
   --More--
    
Table 10  show hw-module subslot errors Field Descriptions

Field

Description

Subslot */*/* errors info

SPA for which error information is being displayed. The location of the SPA is expressed in the rack/slot/module notation.

SPA inserted

Indication if a SPA is currently detected in the subslot.

SPA type

Description of SPA including the technology type, number of ports, height of SPA (HHSPA—single-height, FHSPA—double-height), and optics type.

SPA operational state

Current operational state of the SPA module.

SPA last reset reason

Reason for the most recent reset of this SPA.

SPA last failure reason

Reason for the last failure on this SPA.

Related Commands

Command

Description

show controllers

Displays the controller type and other information.

show hw-module subslot plim-subblock

To display SPA firmware information for a shared port adapter (SPA), use the show hw-module subslot plim-subblock command in

EXEC

XR EXEC

mode.

show hw-module subslot [node-id] plim-subblock

Syntax Description

node-id

(Optional) Location for which to display the specified information. The node-id argument is entered in the rack/slot/module notation.

Command Default

No default behavior or values

Command Modes

EXEC

XR EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Release 5.0.0

This command was introduced.

Release 3.9.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the show hw-module subslot plim-subblock command to display SPA firmware information, both kernel and application information, as well as heartbeat and keepalive information. The show hw-module subslot plim-subblock command is mainly used for debugging purposes.

Task ID

Task ID

Operations

root-lr

read

Examples

The following example shows sample output for the show hw-module subslot plim-subblock command:

RP/0/0/CPU0:router# show hw-module subslot 0/5/0 plim-subblock 
   
  Subslot 0/5/0 Plim Subblock Info:
  -------------------------------------
   
  Firmware information: 
    SPA v4.10.1, ifs-spa_ppc_iox.elf
    Application v3.44.0, spa_ct3_pat_apps_iox.tar.gz
   
  SPA keepalive information: 
    Heartbeat check disabled : FALSE
    Keepalive seq 372638, seen 372637, Time since last ipc keep 1s
    

Related Commands

Command

Description

show controllers

Displays the controller type and other information.

show hw-module subslot registers

To display register information about internal hardware devices for a shared port adapter (SPA), use the show hw-module subslot registers command in

EXEC

XR EXEC

mode.

show hw-module subslot [node-id] registers [ device [ device-index [device-subindex] ] ]

Syntax Description

node-id

(Optional) Location for which to display the specified information. The node-id argument is entered in the rack/slot/module notation.

device

(Optional) Internal hardware device for which to display the specified information. Valid devices include:

  • analog-digital-converter—Displays analog-to-digital converter information.

  • c2w—Displays Cisco-to-wire bus device information.

  • fpga—Displays SPA field-programmable gate array information.

  • framer—Displays SONET framer information. (Not applicable to Ethernet SPAs.)

  • hdlc—Displays SPA hdlc information, where applicable.

  • l2-tcam—Displays SPA Layer 2 ternary content addressable memory information. (Not applicable to POS SPAs.)

  • mac—Displays SPA MAC information. (Not applicable to POS SPAs.)

  • pluggable-optics—Displays pluggable-optics module information.

  • power-margining—Displays power-margining device information.

  • sar—Displays SPA ATM SAR information.

  • sdcc—Displays section data communications channel device information. (Not applicable to Ethernet SPAs.)

  • serdes—Displays SPA serializer/deserializer information.

  • spi4—Displays system packet interface level 4.2 bus device information.

  • temperature-sensor—Displays temperature sensor information.

device-index

(Optional) Index of the specific device if there are multiple devices of the same type.

device-subindex

(Optional) Subindex of the specific device if there are multiple devices of the same device index.

Command Default

No default behavior or values

Command Modes

EXEC

XR EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Release 5.0.0

This command was introduced.

Release 3.9.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the command to display the nodes on the router.

You can also enter a partially qualified location specifier by using the wildcard (*) character. For example, 0/1/* would display information for all modules on slot 1 in rack 0.

Use the show hw-module subslot registers command to display register information for the specified internal hardware device on the SPA.

Task ID

Task ID

Operations

root-lr

read

Examples

The following example shows sample output for the show hw-module subslot registers command:

RP/0/0RP0RSP0/CPU0:router# show hw-module subslot 0/1/cpu0 registers

 Thu Feb 19 00:38:32.908 PST 

Subslot 0/1/0 registers info:
---------------------------
SPA hardware ID : 0x0
SPA SW FPGA rev.: 0x1000A

Subslot 0/1/1 registers info:
---------------------------
SPA hardware ID : 0x0
SPA SW FPGA rev.: 0x1000A

Subslot 0/1/2 registers info:
---------------------------
SPA hardware ID : 0x0
SPA SW FPGA rev.: 0x1000A

Subslot 0/1/3 registers info:
---------------------------
SPA hardware ID : 0x0
SPA SW FPGA rev.: 0x1000A

Subslot 0/1/4 registers info:
---------------------------
SPA hardware ID : 0x0
SPA SW FPGA rev.: 0x1000A

Subslot 0/1/5 registers info:
---------------------------
SPA hardware ID : 0x0
SPA SW FPGA rev.: 0x1000A
  
Table 11  show hw-module subslot registers Field Descriptions

Field

Description

SPA hardware ID

SPA hardware identifier in hexadecimal format.

SPA SW FPGA rev.

SPA software field-programmable gate array (FPGA) revision number in hexadecimal format.

Related Commands

Command

Description

show controllers

Displays the controller type and other information.

show hw-module subslot status

To display status information about internal hardware devices for a shared port adapter (SPA), use the show hw-module subslot status command in EXEC

XR EXEC

mode.

show hw-module subslot [node-id] status [ device [ device-index [device-subindex] ] ]

Syntax Description

node-id

(Optional) Location for which to display the specified information. The node-id argument is entered in the rack/slot/module notation.

device

(Optional) Internal hardware device for which to display the specified information. Valid devices include:

  • analog-digital-converter—Displays analog-to-digital converter information.

  • c2w—Displays Cisco-to-wire bus device information.

  • fpga—Displays SPA field-programmable gate array information.

  • framer—Displays SONET framer information. (Not applicable to Ethernet SPAs.)

  • hdlc—Displays SPA hdlc information, where applicable.

  • l2-tcam—Displays SPA Layer 2 ternary content addressable memory information. (Not applicable to POS SPAs.)

  • mac—Displays SPA MAC information. (Not applicable to POS SPAs.)

  • pluggable-optics—Displays pluggable-optics module information.

  • power-margining—Displays power-margining device information.

  • sar—Displays SPA ATM SAR information.

  • sdcc—Displays section data communications channel device information. (Not applicable to Ethernet SPAs.)

  • serdes—Displays SPA serializer/deserializer information.

  • spi4—Displays system packet interface level 4.2 bus device information.

  • temperature-sensor—Displays temperature sensor information.

device-index

(Optional) Index of the specific device if there are multiple devices of the same type.

device-subindex

(Optional) Subindex of the specific device if there are multiple devices of the same device index.

Command Default

No default behavior or values

Command Modes

EXEC

XR EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Release 5.0.0

This command was introduced.

Release 3.9.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

You can also enter a partially qualified location specifier by using the wildcard (*) character. For example, 0/1/* would display information for all modules on slot 1 in rack 0.

Use the show hw-module subslot status command to obtain status information about an interface on the SPA.

Task ID

Task ID

Operations

root-lr

read

Examples

The following example shows sample output for the show hw-module subslot status command with the temperature-sensor option:

RP/0/0RP0RSP0/CPU0:router# show hw-module subslot 0/2/CPU0 status temperature-sensor
  
   SPA device temperature-sensor index 0 subindex 0 info:
  
  DS1631 (0x0803c2e4) device status:
  temperature = 0x1c80 (28.5 degree C)
  
   SPA device temperature-sensor index 0 subindex 0 info:
  
  DS1631 (0x08063bec) device status:
  temperature = 0x1e00 (30.0 degree C)
    
Table 12  show hw-module subslot status Field Descriptions

Field

Description

DS1631 (0x0803c2e4) device status

Device for which the temperature status is displayed.

temperature = 0x1c80 (28.5 degree C)

Current temperature of the specified device, in hexadecimal format and degrees Celsius.

Related Commands

Command

Description

show controllers

Displays the controller type and other information.

show inventory

To retrieve and display information about all the Cisco products that are installed in the router, use the show inventory command in System Admin EXEC or XR EXEC EXEC or administration EXEC mode.

EXEC Modeshow inventory [ node-id | all | location { node-id | all } | raw ]

Administration EXEC Modeshow inventory [ node-id | all | chassis | fans | location { node-id | all } | power-supply | raw ]

System Admin EXEC Mode show inventory [ all | chassis | fan | location { node-id } | power | raw ]

XR EXEC Mode show inventory [ locationspecifier | all | location { locationspecifier | all } | oid | raw ]

Syntax Description

node-id

(Optional) Location for which to display the specified information. The node-id argument is entered in the rack/slot/module notation.

all

(Optional) Displays inventory information for all the physical entities in the chassis.

location {node-id|all}

(Optional) Displays inventory information for a specific node, or for all nodes in the chassis.

raw

(Optional) Displays raw information about the chassis for diagnostic purposes.

chassis

(Optional) Displays inventory information for the entire chassis.

locationspecifier

(Optional) Displays the name of the location.

oid

(Optional) Displays OID information about the chassis.

fansfan

(Optional) Displays inventory information for the fans.

power-supply power

(Optional) Displays inventory information for the power supply.

Command Default

All inventory information for the entire chassis is displayed.

Command Modes

EXEC

Administration EXEC

System Admin EXEC

XR EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Release 3.3.0

The root-system task ID was removed from the show inventory command.

Release 3.3.0

This command was introduced.

Release 3.5.0

Support for SFP information was added.

Release 3.7.2

This command was introduced.

Release 3.9.0

Support was added for the 2-port channelized OC-12/DS0 SPA.

Release 5.0.0

This command was introduced.

Usage Guidelines

If a Cisco entity is not assigned a product ID (PID), that entity is not retrieved or displayed.

Enter the show inventory command with the raw keyword to display every RFC 2737 entity installed in the router, including those without a PID, unique device identifier (UDI), or other physical identification.


Note


The raw keyword is primarily intended for troubleshooting problems with the show inventory command itself.


If any of the Cisco products do not have an assigned PID, the output displays incorrect PIDs, and version ID (VID) and serial number (SN) elements may be missing.

For UDI compliance products, the PID, VID, and SN are stored in EEPROM and NVRAM. Use the show inventory command to display this information.

Information for the following entities is not provided :

  • Power supply

  • Fan trays and fans

  • Flash memory devices

  • Hard disk

Task ID

Task ID

Operations

sysmgr

read

Examples

The following example shows partial sample output from the show inventory command with the raw keyword:


RP/0/0/CPU0:router(admin)# show inventory raw
  
NAME: "0/1/*", DESCR: "Cisco CRS-1 Series Modular Services Card"
PID: CRS-MSC           , VID: V02, SN: SAD09280BS9
  
NAME: "0/1/* - host", DESCR: "host"
PID:                   , VID: N/A, SN: 
  
NAME: "0/1/* - host - Inlet0", DESCR: "Temperature Sensor"
PID:                   , VID: N/A, SN: 
  
NAME: "0/1/* - host - Inlet1", DESCR: "Temperature Sensor"
PID:                   , VID: N/A, SN: 
  
NAME: "0/1/* - host - Exhaust0", DESCR: "Temperature Sensor"
PID:                   , VID: N/A, SN: 
  
NAME: "0/1/* - host - Exhaust1", DESCR: "Temperature Sensor"
PID:                   , VID: N/A, SN: 
  
NAME: "0/1/* - host - Hotspot0", DESCR: "Temperature Sensor"
PID:                   , VID: N/A, SN: 
  
NAME: "0/1/* - host - 1.25V_ME0", DESCR: "Voltage Sensor"
PID:                   , VID: N/A, SN: 
--More-- 
    

RP/0/RSP0/CPU0:router# show inventory raw

Tue Jul 28 08:49:14.080 DST
NAME: "module 0/RSP0/CPU0", DESCR: "A2K-RSP-4G-HDD="
PID: A2K-RSP-4G-HDD=   , VID: VP4, SN: FOC1230803H

NAME: "module 0/RSP0/CPU0", DESCR: "RSP Card host "
PID:                   , VID: N/A, SN: 

NAME: "temperature 0/RSP0/CPU0", DESCR: "Inlet Temperature Sensor"
PID:                   , VID: N/A, SN: 

NAME: "temperature 0/RSP0/CPU0", DESCR: "Hot Temperature Sensor"
PID:                   , VID: N/A, SN: 

NAME: "voltage 0/RSP0/CPU0", DESCR: "Voltage Sensor - 0.75VTT"
PID:                   , VID: N/A, SN: 

NAME: "voltage 0/RSP0/CPU0", DESCR: "Voltage Sensor - 0.9VTT_A"
PID:                   , VID: N/A, SN: 

NAME: "voltage 0/RSP0/CPU0", DESCR: "Voltage Sensor - 0.9VTT_B"
PID:                   , VID: N/A, SN: 

NAME: "voltage 0/RSP0/CPU0", DESCR: "Voltage Sensor - IBV"
PID:                   , VID: N/A, SN: 

NAME: "voltage 0/RSP0/CPU0", DESCR: "Voltage Sensor - 5.0V"
PID:                   , VID: N/A, SN: 

NAME: "module 0/1/CPU0", DESCR: "Cisco ASR 9000 Series SPA Interface Processor-700"
PID: A9K-SIP-700       , VID: P3A, SN: FHH132800F6

NAME: "module 0/1/0"   , DESCR: "10-port 1 GbE Shared Port Adapter V2"
PID: SPA-2XOC12C       , VID: V02, SN: JAE1239W2AI
--More--
  

RP/0/RP0/CPU0:router# show inventory raw

 Sun Jan 25 07:40:57.903 PST 
NAME: "0/1/*", DESCR: "Cisco CRS-1 Series Modular Services Card"
PID: CRS-MSC           , VID: V02, SN: SAD09280BS9

NAME: "0/1/* - cpu", DESCR: "cpu"
PID:                   , VID: V00, SN: SAD093000JR

NAME: "0/1/* - cpu - 1.6V_P0", DESCR: "Voltage Sensor"
PID:                   , VID: N/A, SN:

NAME: "0/1/* - cpu - 1.8V_A", DESCR: "Voltage Sensor"
PID:                   , VID: N/A, SN:

NAME: "0/1/* - cpu - 2.5V_A", DESCR: "Voltage Sensor"
PID:                   , VID: N/A, SN:

NAME: "0/1/* - cpu - 3.3V_A", DESCR: "Voltage Sensor"
PID:                   , VID: N/A, SN:

NAME: "0/1/* - cpu - 5V_A", DESCR: "Voltage Sensor"
PID:                   , VID: N/A, SN:

NAME: "0/1/* - cpu - Hotspot0", DESCR: "Temperature Sensor"
PID:                   , VID: N/A, SN: 
--More--
  

The following example shows partial sample output from the show inventory command:

RP/0/RP0/CPU0:router# show inventory

Tue Apr 27 02:57:55.671 DST
NAME: "0/6/*", DESCR: "Cisco CRS-1 Series Modular Services Card"
PID: CRS-MSC           , VID: V03, SN: SAD093702ES

NAME: "0/PL6/*", DESCR: "Cisco Carrier Routing System SPA Interface Processor Card"
PID: CRS1-SIP-800      , VID: V01, SN: SAD094203W2

NAME: "0/6/CPU0/129", DESCR: "CPU_PORT_1"
PID:                   , VID: N/A, SN: 

NAME: "0/6/0", DESCR: "4-port OC3/STM1 POS Shared Port Adapter"
PID: SPA-4XOC3-POS     , VID: V01, SN: JAB093309MG

NAME: "0/6/1", DESCR: "Cisco 1-Port 10GE LAN/WAN-PHY Shared Port Adapter"
PID: SPA-1X10GE-WL-V2  , VID: V01, SN: JAE11474EVC

NAME: "0/6/4", DESCR: "8-port OC12/STM4 POS Shared Port Adapters"
PID: SPA-8XOC12-POS    , VID: V01, SN: JAB094706L9

NAME: "0/6/5", DESCR: "8-port Gigabit Ethernet Shared Port Adapter"
PID: SPA-8X1GE         , VID: V01, SN: SAD093909GM

NAME: "0/RP0/*", DESCR: "Cisco CRS-1 Series 8 Slots Route Processor"
PID: CRS-8-RP          , VID: V01, SN: SAD093507HX
--More--
  
sysadmin-vm:0_RP0# show inventory raw

Tue Aug  27 13:32:31.730 UTC

 Name: Rack 0-Chassis        Descr: NCS 6008-8-Slot Chassis
 PID: N/A                    VID: N/A                   SN: N/A

 Name: Rack 0-LineCard Chassis backplane  Descr: NCS 6008-8-Slot Chassis Backplane
 PID: N/A                    VID: N/A                   SN: N/A

 Name: Rack 0-MidPlane IDPROM  Descr: NCS 6008-8-Slot Chassis
 PID: NCS-6008        VID: V01                   SN: SAD12345678

 Name: Rack 0-Line Card Slot 0  Descr: NCS 6008-8-Slot Line Card Slot
 PID: N/A                    VID: N/A                   SN: N/A

 Name: 0/0-Card              Descr: NCS 6000 10x100G Multi-Service CXP P0
 PID: N/A                    VID: N/A                   SN: N/A

 Name: 0/0-Motherboard       Descr: Motherboard Module
 PID: N/A                    VID: N/A                   SN: N/A
--More--

Table 1 describes the significant fields shown in the display.

Table 13  show inventory Field Descriptions

Field

Description

NAME

Hardware for which the inventory information is displayed. If you are displaying the chassis inventory, this field shows “chassis.” If you are displaying raw inventory, or all inventory information for all nodes in the chassis, this field shows the node name in partially qualified format. For a node, the NAME is expressed in rack/slot/module notation.

DESCR

Describes the chassis or the node.

Chassis descriptions provide the name of the chassis and its Gbps. Node descriptions provide the type of node and its software version.

A description value of “CPU_PORT_0” indicates a control Ethernet port on the CPU module.

PID

Physical model name of the chassis or node.

VID

Physical hardware revision of the chassis or node.

SN

Physical serial number for the chassis or node.

show led

To display LED information for the router, or for a specific LED location, use the show led command in System Admin EXECEXEC or administration EXEC mode.

show led [ location { node-id | all } ]

show led [ location [node-id] | trace { all | trace-name } location node-id [ all | trace-attributes ] ]

Syntax Description

location {node-id | all}

(Optional) Specifies the node for which to display LED information. The node-id argument is expressed in the rack/slot/module notation. Use the all keyword to indicate all nodes.

location node-id

Specifies the node for which to display LED information. The node-id argument is entered in the rack/slot/module notation.

trace

Displays LED debug traces information.

trace-name

Trace name.

location node-id

Specifies the target location. The node-id argument is expressed in the rack/slot notation.

trace-attribute

Trace attribute.

all

Displays all the details.

Command Default

If no node is specified, information about all LEDs on the router is displayed.

Command Modes

EXEC

Administration EXEC

System Admin EXEC

Command History

Release

Modification

Release 2.0

This command was introduced.

Release 3.2

This command was introduced.

Release 3.3.0

The show led command was moved from the root-system task ID to the system task ID.

The show led command was supported in administration EXEC mode.

Release 3.7.2

This command was introduced.

Release 5.0.0

This command was introduced.

Usage Guidelines

Enter the show platform command to see the location of all nodes installed in the router.

Task ID

Task ID

Operations

system

read

Examples

The following example sample output from the show led command with the all keyword:


RP/0/0RP0RSP0/CPU0:router# show led location all
  
       LOCATION        MESSAGE        MODE      STATUS
      ==================================================
           0/1/*       IOS XR        DEFAULT   UNLOCKED
           0/4/*       ACTVDRP       DEFAULT   UNLOCKED
           0/6/*       IOS XR        DEFAULT   UNLOCKED
         0/RP0/*       ACTV RP       DEFAULT   UNLOCKED
         0/RP1/*       STBYRDY       DEFAULT   UNLOCKED
     

RP/0/RP0/CPU0:router# show led location all

Thu Jul 30 05:26:24.896 DST
    Location         Message     Mode     Status
  ===================================================
     0/RSP0/*            ACTV   DEFAULT  UNLOCKED
       
       

RP/0/0/CPU0:router# show led location all
  
       LOCATION        MESSAGE        MODE      STATUS
      ==================================================
        0/0/CPU0       ACTVRP        DEFAULT   UNLOCKED
        0/1/CPU0           PSC1      DEFAULT   UNLOCKED
        0/2/CPU0       IOX RUN       DEFAULT   UNLOCKED
        0/3/CPU0       IOX RUN       DEFAULT   UNLOCKED
        0/4/CPU0       IOX RUN       DEFAULT   UNLOCKED
        0/5/CPU0       IOX RUN       DEFAULT   UNLOCKED

  
sysadmin-vm:0_RP0# show led
Tue Aug  27 13:44:33.770 UTC
=============================================================
Location  LED Name                      Mode         Color
=============================================================
0/0
          0/0-Attention LED             WORKING     OFF
          0/0-Status LED                WORKING     GREEN
0/1
          0/1-Attention LED              -           -
          0/1-Status LED                 -           -
0/RP0
          0/RP0-Attention LED           WORKING     OFF
          0/RP0-Status LED              WORKING     GREEN
          0/RP0-Alarm Minor LED         WORKING     AMBER
          0/RP0-Alarm Major LED         WORKING     AMBER
          0/RP0-Alarm Critical LED      WORKING     OFF
0/RP1
          0/RP1-Attention LED           WORKING     OFF
          0/RP1-Status LED              WORKING     GREEN
          0/RP1-Alarm Minor LED         WORKING     AMBER
          0/RP1-Alarm Major LED         WORKING     AMBER
          0/RP1-Alarm Critical LED      WORKING     OFF
0/FC0
          0/FC0-Attention LED           WORKING     OFF
Table 14  show led location Field Descriptions

Field

Description

LOCATION

Location of the node. LOCATION is expressed in the rack/slot/module notation.

MESSAGE

Current message displayed by the LED.

MODE

Current operating mode of the specified node.

STATUS

Current status of the specified node.

Table 15  show led location Field Descriptions

Field

Description

LOCATION

Location of the node. LOCATION is expressed in the rack/slot/module notation.

LED Name

Name of the LED.

MODE

Current operating mode of the specified node.

COLOR

Color of the LED.


Related Commands

Command

Description

led mode

Changes the message, mode or status of a router card LED display.

show mbus

To display Mbus Controller Area Network (CAN) errors and interface counters, use the show mbus command in administration EXEC mode.

show mbus { can-error | counters } location { node-id | all }

Syntax Description

can-error

Displays CAN bus error statistics.

counters

Displays information about the firmware packets that were dropped.

location{node-id | all}

Specifies the node for which to display Mbus information. The node-id argument is expressed in the rack/slot/module notation. Use the all keyword to indicate all nodes.

Command Default

No default behavior or values

Command Modes

Administration EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Release 3.3.0

The root-system task ID was removed from the show mbus command.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

sysmgr

read

Examples

This example shows sample output from the show mbus command with the can-error and location keywords:

RP/0/0/CPU0:router# admin
RP/0/0/CPU0:router(admin)# show mbus can-error location 0/0/CPU0
  
  Slot #  Stuff   Form    Ack     Bit_1   Bit_0   CRC
  0       0       0       0       0       0       0
    
Table 16  show mbus can-error Field Descriptions

Field

Description

Slot

Slot that contains the node whose Mbus counters are displayed.

Stuff

Number of stuff errors on the node.

Form

Number of form errors on the node.

Ack

Number of acknowledgement errors on the node.

Bit_1

Number of Bit_1 errors on the node.

Bit-0

Number of Bit_0 errors on the node.

CRC

Number of cyclic redundancy check (CRC) errors.

The following example shows sample output from the show mbus command with the location keyword:

RP/0/0/CPU0:router# admin
RP/0/0/CPU0:router(admin)# show mbus counters location 0/0/CPU0
  
  Slot #  Mbox    Mbox    Mbus    Mbus    Obj
          Xmit    Rcv     Xmit    Rcv     Ovr_wr
  0       0       0       0       0       0
    
Table 17  show mbus counters Field Descriptions

Field

Description

Slot

Identifies the slot that contains the node whose Mbus counters are displayed.

Mbox Xmit

Number of packets dropped due to Mbox transmit errors.

Note   

MBox is a chunk of the Maintenance Processor Data Memory (MP DMEM) that receives MIPC messages. The Norm Priority mailbox has a buffer of 32 KB, while the high-priority Mbox has a buffer of 8 KB.

Mbox Rcv

Number of packets dropped due to Mbox receive errors.

Mbus Xmit

Number of packets dropped due to Mbus transmit errors.

Note   

The Mbus is a low-bandwidth (1 megabit per second) serial bus that connects cards, switch fabric cards, power supplies, and blower/fan assemblies to the performance route processors (PRPs) and counters.

Mbus Rcv

Number of packets dropped due to Mbus receive errors.

Obj Ovr_wr

Number of packets that were overwritten.

Related Commands

Command

Description

clear mbus-statistics location

Clears all Mbus interface counters on a specific node.

show operational

To display all operational data provided as XML schema, use the show operational command in

EXEC or administration EXEC

XR EXEC

mode.

show operational mda-class [mda-class] [mda-class/naming=value] [descriptive]

Syntax Description

mda-class

Name of the management data API (MDA) class to output. To specify a class name in hierarchy, all classes must be specified from the top of the class to the specific class name that you are interested in. MDA classes are case-sensitive.

To view all available MDA classes, use the question mark (?) online help function.

descriptive

Displays more descriptive information.

Command Default

No default behavior or values

Command Modes

EXEC

Administration EXEC

XR EXEC

Command History

Release

Modification

Release 3.6.0

This command was introduced.

Release 5.0.0

This command was introduced.

Release 3.7.2

This command was introduced.

Release 3.9.0

Support was added for the 2-Port Channelized OC-12/DS0 SPA.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Although the show operational command uses the schema database, the command displays the information in a string format like the other show commands. No XML related setups or knowledge is required to use the command.

Task ID

Task ID

Operations

Depends on the MDA class for which you are displaying the information

read

Examples

The following example shows sample output from the show operational command. Not all the output is shown.

RP/0/0RP0RSP0/CPU0:router# show operational BGP DefaultVRF GlobalProcessInfo descriptive
[BGP DefaultVRF GlobalProcessInfo]
InStandaloneMode: true[Standalone or Distributed mode]
RouterID: 0.0.0.0[Router ID for the local system]
ConfiguredRouterID: 0.0.0.0[Configured router ID]
LocalAS: 10[Local autonomous system #]
RestartCount: 1[No of times BGP has started]
ISRedistributeIBGPToIGPsEnabled: false[Redistribute iBGP into IGPs enabled]
IsFastExternalFalloverEnabled: true[Fast external fallover enabled]
IsBestpathMissingMEDIsWorstEnabled: false[Bestpath: Treat missing MED as worst]
.
.
.
DefaultLocalPreference: 100[Default local preference]
KeepAliveTime: 60[Default keepalive timer (seconds)]
HoldTime: 180[Default hold timer (seconds)]
GenericScanPeriod: 60[Period (in seconds) of generic scanner runs]
.
.
.
VrfIsActive: true[VRF state ]
VrfName: "default"[Name of the VRF ]
    

This example shows sample output from the show operational command where only the top-level MDA class is specified. Not all of the output is shown.

RP/0/0RP0RSP0/CPU0:router# show operational Inventory

Thu Feb 19 00:54:41.251 PST 
[Inventory]
RackTable
  Rack/Number=0
    SlotTable
      Slot/Number=0
        CardTable
          Card/Number=0
            PortSlotTable
              PortSlot/Number=0
                Port
                  BasicAttributes
                    BasicInfo
                      Description: CPU_PORT_0
                      VendorType: 1.3.6.1.4.1.9.12.3.1.10
                      Name: 0/0/SP/0
                      IsFieldReplaceableUnit: false
                      CompositeClassCode: 983040
                BasicAttributes
                  BasicInfo
                    Description: CE Port Slot
                    VendorType: 1.3.6.1.4.1.9.12.3.1.5.115
                    Name: portslot 0/0/SP/0
                    IsFieldReplaceableUnit: false
                    CompositeClassCode: 0
            SensorTable
              Sensor/Number=0
                BasicAttributes
                  BasicInfo
                    Description: Temperature Sensor
                    VendorType: 1.3.6.1.4.1.9.12.3.1.8.42
                    Name: 0/0/* - host - Inlet0
                    CompositeClassCode: 720898
                    EnvironmentalMonitorPath: /admin/oper/inventory/
                     rack/0/entity/0/entity/0/entity/0/entity/0/attrib/
              Sensor/Number=1
                BasicAttributes
                  BasicInfo
                    Description: Temperature Sensor
                    VendorType: 1.3.6.1.4.1.9.12.3.1.8.42
                    Name: 0/0/* - host - Inlet1
                    CompositeClassCode: 720898
                    EnvironmentalMonitorPath: /admin/oper/inventory/
                     rack/0/entity/0/entity/0/entity/0/entity/1/attrib/
              Sensor/Number=2
                BasicAttributes
                  BasicInfo
                    Description: Temperature Sensor
                    VendorType: 1.3.6.1.4.1.9.12.3.1.8.42
                    Name: 0/0/* - host - Exhaust0
                    CompositeClassCode: 720898
 --More--
  

show platform

To display information and status for each node in the system, use the show platform command in EXEC or administration EXEC System Admin EXEC or XR EXEC mode.

show platform [node-id]

show platform aib trace { all | fast | slow } client client-name errors events [hexdump] [ last n ] [reverse] [stats] [tailf] [unique] [updates] [verbose] [wrapping] [ file filename original ] [ location { node-id | all } ]

System Admin EXEC Mode show platform [ detail | slices ] [ location [node-id] ]

XR EXEC Mode show platform

Syntax Description

node-id

(Optional) Node for which to display information. The node-id argument is entered in the rack/slot/module notation.

aib trace

Displays adjacency information base (AIB) traces.

all

Displays trace data for all events.

fast

Displays trace data for frequent events.

slow

Displays trace data for infrequent events.

client client-name

Displays the trace for AIB client calls.

errors

Displays the trace for AIB client errors.

events

Displays the trace for AIB client events.

hexdump

(Optional) Displays traces in hexadecimal format.

last n

(Optional) Displays the last n number of traces only.

reverse

(Optional) Displays the most recent traces first.

stats

(Optional) Displays execution path statistics.

tailf

(Optional) Displays new traces as they are added.

unique

(Optional) Displays unique entries only, along with the count of the number of times this entry appears.

verbose

(Optional) Displays additional internal debugging information.

updates

(Optional) Displays trace AIB client API updates.

wrapping

(Optional) Displays wrapping entries.

file filename original

(Optional) Specifies the filename of the file to display. You can specify up to four trace files.

location {node-id | all}

(Optional) Specifies the node of the RPRPRSP. The node-id argument is entered in the rack/slot/module notation. You can specify up to four nodes. The all keyword specifies all RPRPRSP nodes.

detail

Displays details of node type and state.

slices

Displays summary of node forwarding slices.

location node-id

Specifies the target node. The node-id argument is entered in the rack/slot/module notation.

Command Default

Status and information are displayed for all nodes in the system.

None

Command Modes

Administration EXEC

EXEC

System Admin EXEC

XR EXEC

Command History

Release

Modification

Release 2.0

This command was introduced.

Release 3.2

This command was introduced.

Release 3.3.0

The show platform command was first supported in administration EXEC mode.

In EXEC mode, the show platform command was moved from the root-system task ID to the system task ID.

Release 3.7.2

This command was introduced.

Release 3.9.0

Support for the aib keyword was added.

Release 3.9.0

Support was added for the 2-Port Channelized OC-12/DS0 SPA.

Release 5.0.0

This command was introduced.

Usage Guidelines

The show platform command provides a summary of the nodes in the system, including node type and status.

Enter the show platform command in administration EXEC mode to display output for the entire system. Enter the show platform command in EXEC mode to display output for only those nodes that belong to the SDR on which the command is executed.

For ASR-9001-S, EP1 will be displayed as, Not allowed online, until the required license is bought.

Task ID

Task ID

Operations

sysmgr

read

system

read (in EXEC mode)

root-system

read (in administration EXEC mode)

Examples

This example shows the sample display output for ASR9912 and ASR9922:

RP/0/0RP0RSP0/CPU0:router:router(admin) # show platform
Wed Jul  3 11:34:18.487 UTC
Node            Type                      State            Config State
-----------------------------------------------------------------------------
0/RP0/CPU0      ASR-9922-RP-SE(Active)    IOS XR RUN       PWR,NSHUT,MON
0/RP1/CPU0      ASR-9922-RP-TR(Standby)   IOS XR RUN       PWR,NSHUT,MON
0/FT0/SP        FAN TRAY                  READY            
0/FT1/SP        FAN TRAY                  READY            
0/0/CPU0        A9K-36x10GE-TR            IOS XR RUN       PWR,NSHUT,MON
0/1/CPU0        A9K-36x10GE-SE            IOS XR RUN       PWR,NSHUT,MON
0/2/CPU0        A9K-36x10GE-TR            IOS XR RUN       PWR,NSHUT,MON
0/3/CPU0        A9K-36x10GE-SE            IOS XR RUN       PWR,NSHUT,MON
0/4/CPU0        A9K-36x10GE-SE            IOS XR RUN       PWR,NSHUT,MON
0/5/CPU0        A9K-36x10GE-SE            IOS XR RUN       PWR,NSHUT,MON
0/6/CPU0        A9K-36x10GE-SE            IOS XR RUN       PWR,NSHUT,MON
0/7/CPU0        A9K-36x10GE-TR            IOS XR RUN       PWR,NSHUT,MON
0/8/CPU0        A9K-24x10GE-SE            IOS XR RUN       PWR,NSHUT,MON
0/9/CPU0        A9K-24x10GE-TR            IOS XR RUN       PWR,NSHUT,MON
0/PM0/SP        PWR-3KW-AC-V2             READY            PWR,NSHUT,MON
0/PM1/SP        PWR-3KW-AC-V2             READY            PWR,NSHUT,MON
0/PM2/SP        PWR-3KW-AC-V2             READY            PWR,NSHUT,MON
0/PM3/SP        PWR-3KW-AC-V2             READY            PWR,NSHUT,MON
0/PM4/SP        PWR-3KW-AC-V2             READY            PWR,NSHUT,MON
0/PM5/SP        PWR-3KW-AC-V2             READY            PWR,NSHUT,MON
0/FC0/SP        ASR-9912-SFC110           OK               PWR,NSHUT,MON
0/FC1/SP        ASR-9912-SFC110           OK               PWR,NSHUT,MON
0/FC2/SP        ASR-9912-SFC110           OK               PWR,NSHUT,MON
0/FC3/SP        ASR-9912-SFC110           OK               PWR,NSHUT,MON
0/FC4/SP        ASR-9912-SFC110           OK               PWR,NSHUT,MON
0/FC5/SP        ASR-9912-SFC110           OK               PWR,NSHUT,MON
0/FC6/SP        ASR-9912-SFC110           OK               PWR,NSHUT,MON

The following example shows sample output from the show platform command:

RP/0/RP0/CPU0:router# show platform
  
  Node            Type            PLIM            State           Config State
  -----------------------------------------------------------------------------
  0/1/CPU0        MSC             Jacket Card     IOS XR RUN      PWR,NSHUT,MON
  0/1/0           MSC(SPA)        4XOC3-POS       OK              PWR,NSHUT,MON
  0/1/5           MSC(SPA)        8X1GE           OK              PWR,NSHUT,MON
  0/6/CPU0        MSC             Jacket Card     IOS XR RUN      PWR,NSHUT,MON
  0/6/0           MSC(SPA)        4XOC3-POS       OK              PWR,NSHUT,MON
  0/6/4           MSC(SPA)        8XOC3/OC12-POS  OK              PWR,NSHUT,MON
  0/6/5           MSC(SPA)        8X1GE           OK              PWR,NSHUT,MON
  0/RP0/CPU0      RP(Active)      N/A             IOS XR RUN      PWR,NSHUT,MON
  0/RP1/CPU0      RP(Standby)     N/A             IOS XR RUN      PWR,NSHUT,MON
  
sysadmin-vm:0_RP0#show platform
Wed Aug  28 06:49:49.822 UTC
Location  Card Type               HW State      SW State      Config State
----------------------------------------------------------------------------
0/RP0     NC6-RP                  OPERATIONAL   OPERATIONAL   NSHUT
0/RP1     NC6-RP                  OPERATIONAL   OPERATIONAL   NSHUT
0/FC0     NC6-FC                  OPERATIONAL   N/A           NSHUT
0/FT0     P-L-FANTRAY             OPERATIONAL   N/A           NSHUT
0/FT1     P-L-FANTRAY             OPERATIONAL   N/A           NSHUT
0/3       NC6-10X100G-M           OPERATIONAL   OPERATIONAL   NSHUT
0/PT1     NCS-AC-PWRTRAY          OPERATIONAL   N/A           NSHUT
RP/0/RP0/CPU0:router# show platform

Thu Nov 19 21:44:49.274 UTC
Node            Type                      State            Config State
-----------------------------------------------------------------------------
0/RSP0/CPU0     A9K-RSP-4G(Active)        IOS XR RUN       PWR,NSHUT,MON
0/RSP1/CPU0     A9K-RSP-4G(Standby)       IN-RESET         PWR,NSHUT,MON
0/1/CPU0        A9K-SIP-700               IOS XR RUN       PWR,NSHUT,NMON
0/1/0           SPA-10X1GE-V2             OK               PWR,NSHUT,MON
0/1/1           SPA-1X10GE-L-V2           OK               PWR,NSHUT,MON
0/3/CPU0        A9K-40GE-B                IOS XR RUN       PWR,NSHUT,MON
0/4/CPU0        A9K-SIP-700               IOS XR RUN       PWR,NSHUT,MON
0/4/1           SPA-2XCHOC12/DS0          OK               PWR,NSHUT,MON
  
RP/0/0/CPU0:router# show platform

Tue Jul 28 06:02:02.397 DST
Node            Type            PLIM            State           Config State
-----------------------------------------------------------------------------
0/0/CPU0        L3 Service Eng  N/A             Card Power down NPWR,NSHUT,MON
0/1/CPU0        L3 Service Eng  N/A             Card Power down NPWR,NSHUT,MON
0/2/CPU0        L3LC Eng 5+     Jacket Card     IOS XR RUN      PWR,NSHUT,MON
0/2/0           SPA             SPA-4XOC3-POS-V READY           PWR,NSHUT
0/2/1           SPA             SPA-IPSEC-2G-2  READY           PWR,NSHUT
0/2/2           SPA             SPA-8XFE-TX     READY           PWR,NSHUT
0/3/CPU0        L3LC Eng 5+     Jacket Card     IOS XR RUN      PWR,NSHUT,MON
0/3/1           SPA             SPA-1XCHOC12/DS READY           PWR,NSHUT
0/4/CPU0        L3LC Eng 5+     Jacket Card     IOS XR RUN      PWR,NSHUT,MON
0/4/0           SPA             SPA-2X1GE-V2    READY           PWR,NSHUT
0/4/1           SPA             SPA-2XOC48POS/R READY           PWR,NSHUT
0/4/2           SPA             SPA-2CHT3-CE-AT READY           PWR,NSHUT
0/4/3           SPA             SPA-4XT3/E3     READY           PWR,NSHUT
0/5/CPU0        PRP(Active)     N/A             IOS XR RUN      PWR,NSHUT,MON
  

The following is sample output for the show platform command with the node-id argument:

RP/0/RP0/CPU0:router# show platform 0/1/0
  
  Node            Type            PLIM            State           Config State
  -----------------------------------------------------------------------------
  0/1/0           MSC(SPA)        4XOC3-POS       OK              PWR,NSHUT,MON
  
RP/0/RSP0/CPU0:router# show platform 0/1/cpu0

Mon Jul 27 22:30:04.752 DST
Node            Type                      State            Config State
-----------------------------------------------------------------------------
0/1/CPU0        A9K-40GE-B                IOS XR RUN       PWR,NSHUT,MON
  
This table describes the significant fields shown in the display.

Table 18  show platform Field Descriptions

Field

Description

Node

Identifier of the node in the rack/slot/module notation.

Type

Type of node.

PLIM

Type of physical layer interface module currently supported on the module.

State

Current state of the specified node.

Config State

Current status of the specified node.

This example shows sample output for the show platform command with the aib trace keywords:

RP/0/5/CPU0:router# show platform aib trace slow last 10

Tue Sep 22 12:05:42.382 DST
6 unique entries (768 possible, 0 filtered)
Sep 17 00:38:09.189 c12000_aib/slow/GSR_AIB_LTRACE 0/5/CPU0 1# t1  
  Starting a ltrace in gsr_aib
Sep 17 00:46:01.105 c12000_aib/slow/GSR_AIB_FIB_MBOX_LTRACE 0/5/CPU0 3# t3  
  Starting a ltrace in gsr_aib_fib_mbox
Sep 17 00:46:01.107 c12000_aib/slow/GSR_AIB_LB_MBOX_API_LTRACE 0/5/CPU0 3# t3    
  Starting a ltrace in gsr_aib_lb_mbox_api
Sep 17 05:10:06.560 c12000_aib/slow/GSR_AIB_FIB_MBOX_LTRACE 0/5/CPU0 88# t3   
  GSR_SVI_FIBMB_GET_INFO: Invalid non-svi ext_type 0 for adj 0x9c389b68
Sep 21 20:03:18.977 c12000_aib/slow/GSR_AIB_FIB_MBOX_LTRACE 0/5/CPU0 42# t4  
  GSR_FIBMB_GET_L3_INFO: err, mbp: 0x9d3764d0 flags: 0x0
Sep 22 12:05:04.505 c12000_aib/slow/GSR_AIB_LTRACE 0/5/CPU0 41664# t1  
  AIB_PLATFORM_ALLOC_INDEX_GSR: Alloc failed Resource temporarily unavailable
  

Related Commands

Command

Description

show environment

Displays environmental monitor parameters for the system.

show plugin slot counts

To display cumulative and running counts of card inserts per slot, use the show plugin slot counts command in administration EXEC mode.

show plugin slot counts location { all | node-id }

Syntax Description

location {all node-id} Displays plugin slot counts on the designated node or all nodes. The node-id argument is expressed in the rack/slot/module notation.

Command Default

None

Command Modes

Administration EXEC

Command History

Release Modification

Release 3.9.1

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the show plugin slot counts command to display the number of insertions that have been made to the router backplane for a specific line card or RSP. This command can be used only if the BPID-02 card is installed. If the BPID-02 card is not installed, the following error message is displayed:

Response error: 'ENVMON' detected the 'warning' condition 'Hardware not available'

Task ID

Task ID Operation

sysmgr

read

Examples

This example illustrates sample output from the show plugin slot counts command:

RP/0/RSP0/CPU0:router(admin)# show plugin slot counts location all        

Tue Oct  6 13:37:15.706 pst

Backplane connector slot plugin counters

             Current         Cumulative
0/0/CPU0         176                176
0/1/CPU0          11                 11
0/2/CPU0           0                  0
0/3/CPU0           0                  0
0/RSP0/CPU0        0                  0
0/RSP1/CPU0        1                  1
0/4/CPU0           9                  9
0/5/CPU0           0                  0
0/6/CPU0          12                 12
0/7/CPU0           0                  0
0/FT0/SP           4                  4
0/FT1/SP          14                 14
  

Related Commands

Command

Description

clear plugin slot counts

Clears the running counts of the backplane connector slot plugins.  

show canbus server-stats

Displays the statistics regarding the CAN bus.  

show redundancy

To display the status of route processor redundancy, use the show redundancy command in

EXEC

XR EXEC

mode.

show redundancy [ [ driver [lc] ] location { node-id | all } | statistics | summary ]

Syntax Description

driver

(Optional) Dumps the arbitration driver data.

lc

(Optional) Displays the primary standby arbitration line card data.

location {node-id | all}

(Optional) Specifies the node for which to display LED information. The node-id argument is expressed in the rack/slot/module notation. Use the all keyword to indicate all nodes.

statistics

(Optional) Displays redundancy statistics information.

summary

(Optional) Displays a summary of all redundant node pairs in the router.

Command Default

Route processor redundancy information is displayed for all nodes in the system.

Command Modes

EXEC

XR EXEC

Command History

Release

Modification

Release 2.0

This command was introduced.

Release 5.0.0

This command was introduced.

Release 3.2

This command was introduced.

Release 3.5.0

The statistics and trace keywords were added.

Release 3.6.0

Nonstop routing (NSR) indication was added to the command display.

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the show redundancy command to display the redundancy status of the route processors (RPs)route switch processors (RSPs). The show redundancy command also displays the boot and switchover history for the RPsRPsRSPs. To view the nonstop routing (NSR) status of the standby RPsRPsRSPs in the system, use the summary keyword.

Task ID

Task ID

Operations

system

read

basic-services

read (for statistics keyword)

Examples

The following example shows sample output from the show redundancy command:

RP/0/RP0/CPU0:router# show redundancy location 0/rp0/cpu0

Node 0/RP0/CPU0 is in ACTIVE role
Partner node (0/RP1/CPU0) is in STANDBY role
Standby node in 0/RP1/CPU0 is ready
Standby node in 0/RP1/CPU0 is NSR-ready

Reload and boot info
----------------------
RP reloaded Mon Jul 30 19:27:42 2007: 2 weeks, 1 day, 13 hours, 
40 minutes ago
Active node booted Mon Jul 30 19:27:42 2007: 2 weeks, 1 day, 
13 hours, 40 minutes ago
Standby node boot Mon Jul 30 19:28:13 2007: 2 weeks, 1 day, 
13 hours, 39 minutes ago
Standby node last went not ready Mon Jul 30 20:27:00 2007: 
2 weeks, 1 day, 12 hours, 41 minutes ago
Standby node last went ready Mon Jul 30 20:27:00 2007: 2 weeks, 
1 day, 12 hours, 41 minutes ago
There have been 0 switch-overs since reload    
 
RP/0/RSP0/CPU0:router# show redundancy location 0/rsp0/cpu0
Thu Jul 30 05:47:12.155 DST
Node 0/RSP0/CPU0 is in ACTIVE role
Node 0/RSP0/CPU0 has no valid partner

Reload and boot info
----------------------
A9K-RSP-4G reloaded Tue Jul 14 15:21:30 2009: 2 weeks, 1 day, 
14 hours, 25 minutes ago
Active node booted Tue Jul 14 15:21:30 2009: 2 weeks, 1 day, 
14 hours, 25 minutes ago

Active node reload "Cause: User initiated forced reload all"
 
Table 19  show redundancy Field Descriptions

Field

Description

Node */*/* is in XXX role

Current role of the primary route processor, where (*/*/*) is the route processor ID in the format rack/slot/module, and XXX is the role of the route processor (active or standby).

In the example, this field shows that the node with the ID 0/RP0/CPU0 is in active role.

Partner node (*/*/*) is in XXX role

Current role of the secondary (or partner) route processor, where (*/*/*) is the route processor ID in the rack/slot/module format, and XXX is the role of the route processor (active or standby).

In the example, this field shows that the node with the ID 0/RP1/CPU0 is in standby role.

Standby node in (*/*/*) is ready

Current state of the standby node, where (*/*/*) is the standby route processor ID.

In the example, the standby node is ready.

Standby node in (*/*/*) is NSR-ready

Current state of the standby node regarding nonstop routing (NSR), where (*/*/*) is the standby route processor ID.

In the example, the standby node is NSR-ready.

Reload and boot info

General overview of the active and standby route processors’ reload and boot history.

The following sample output shows the status of the redundant RPs in the system. The status of the standby node is indicated in parentheses next to the node identifier. The nonstop routing (NSR) status is indicated following NSR. Possible values are Ready and Not ready.

RP/0/RP0/CPU0:router# show redundancy summary
  
  Active Node    Standby Node
  ----------    ------------
  0/4/CPU0             N/A
  0/4/CPU1             N/A
  0/RP0/CPU0      0/RP1/CPU0 (Ready, NSR: Ready)
  

Examples

The following example shows sample output from the show redundancy command:

RP/0/0/CPU0:router# show redundancy

Redundancy information for node 0/0/CPU0:
==========================================
Node 0/0/CPU0 is in ACTIVE role
Node 0/0/CPU0 has no valid partner

Reload and boot info
----------------------
PRP reloaded Wed Mar 15 19:50:31 2006: 1 week, 5 days, 18 hours, 
57 minutes ago
Active node booted Wed Mar 15 19:50:31 2006: 1 week, 5 days, 18 hours, 
57 minutes ago

Redundancy information for node 0/1/CPU0:
==========================================
Node 0/1/CPU0 is in ACTIVE role
Node 0/1/CPU0 has no valid partner

Reload and boot info
----------------------
PSC1 reloaded Wed Mar 15 19:51:31 2006: 1 week, 5 days, 18 hours, 56 minutes ago
Active node booted Wed Mar 15 19:51:31 2006: 1 week, 5 days, 18 hours, 56 minutes ago
  
Table 20  show redundancy Field Descriptions

Field

Description

Node */*/* is in XXX role

Current role of the primary route processor, where (*/*/*) is the route processor ID in the format rack/slot/module, and XXX is the role of the route processor (active or standby).

In the example, this field shows that the node with the ID 0/RP0/CPU0 is in active role.

Partner node (*/*/* ) is in XXX role

Current role of the secondary (or partner) route processor, where (*/*/*) is the route processor ID in the rack/slot/module format, and XXX is the role of the route processor (active or standby).

In the example, this field shows that the node with the ID 0/RP1/CPU0 is in standby role.

Standby node in (*/*/* ) is ready

Current state of the standby node, where (*/*/*) is the standby route processor ID.

In the example, the standby node is ready.

Reload and boot info

General overview of the active and standby route processors’ reload and boot history.


Related Commands

Command

Description

redundancy switchover

Causes the primary (active) route processor (RP) to fail over to the redundant standby RP.

show screddrv

To display system controller (SC) redundancy information, use the show screddrv command in EXEC mode.

show screddrv [ all | standby ]

Syntax Description

all

(Optional) Displays redundancy details for the entire router.

standby

(Optional) Displays detailed redundancy information for the standby node.

Command Default

SC redundancy information is displayed for all nodes in the system.

Command Modes

EXEC

Command History

Release

Modification

Release 2.0

This command was introduced.

Release 3.0

No modification.

Release 3.2

No modification.

Release 3.3.0

The show screddrv command was moved from the root-system task ID to the system task ID.

The arbitration keyword was removed from the show screddrv command.

Release 3.4.0

No modification.

Release 3.5.0

No modification.

Release 3.6.0

No modification.

Release 3.7.0

No modification.

Release 3.7.2

This command was introduced.

Release 3.8.0

No modification.

Release 3.9.0

No modification.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Enter the show screddrv command without any of the optional parameters to display summarized SC redundancy and arbitration information for the router.

Task ID

Task ID

Operations

system

read

Examples

The following is sample output from the show screddrv command with the all keyword:

RP/0/0RP0RSP0/CPU0:router# show screddrv all
  
  Redundancy Driver Info for slot 32:
  Slot=32
  Role=active role
  State=ACTIVE STATE
  Prefer_slot=0
  Registers: ICreg=[1], MSreg=[33], MPPReg=[c0005cc8]
  Tx error count=0
  Rx error count=22
  Comm Statistics=5632
  SHOW REDDRV ARBITRATION is not supported.
    
Table 21  show screddrv Field Descriptions

Field

Description

Role

Current role of the card in the specified slot; for example, it may be active, standby, and so forth.

State

Current state of the card in the specified slot.

Prefer_slot

Information about the preferred redundancy slot.

Registers

Information about the following registers:

  • ICreg

  • MSreg

  • MPPReg

Tx error count

Number of transmit errors that have occurred on the card in the specified slot.

Rx error count

Number of receive errors that have occurred on the card in the specified slot.

Comm Statistics

Command statistics.

SHOW REDDRV ARBITRATION

Describes whether arbitration is supported or not on this slot. If arbitration is supported, this field provides arbitration information.

show services redundancy

To display all configured services and their active and standby physical locations, use the show services redundancy command in EXEC mode.

show services redundancy [ type service ] [ brief | detail | summary ] [ location node-id ]

Syntax Description

type service

Displays data for a specified service type only.

brief

Displays brief data.

detail

Displays detailed data, including auto-revert setting.

summary

Displays summary data.

location node-id

Location for which to display the specified information. The node-id argument is entered in the rack/slot/module module notation.

Command Default

Displays brief data, as when the brief keyword is used.

Command Modes

EXEC

Command History

Release

Modification

Release 3.3.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Examples

This example shows sample brief data for all services:

RP/0/0/CPU0:router# show services redundancy      

Tue Nov 11 10:09:57.382 PST DST
Service type     Name                    Pref. Active        Pref. Standby      
--------------------------------------------------------------------------------
Firewall         Admin_1                 0/1/CPU0 Active    
SBC              service-1               0/0/CPU0 Active    
IPSec            service-ipsec1          0/2/1    Active    
GRE              service-gre1            0/2/1    Active    
  

The following sample output shows details of all configured services:

RP/0/0/CPU0:router# show services redundancy detail

Tue Nov 11 09:24:15.541 PST DST
Service 'Admin_1' of type 'Firewall':
  Preferred active at 0/1/CPU0, Active
  Auto-revert is OFF
Service 'service-1' of type 'SBC':
  Preferred active at 0/0/CPU0, Active
  Auto-revert is OFF
Service 'service-ipsec1' of type 'IPSec':
  Preferred active at 0/2/1, Active
  Auto-revert is OFF
Service 'service-gre1' of type 'GRE':
  Preferred active at 0/2/1, Active
  Auto-revert is OFF  
  

The following sample output shows a summary of all configured services:

RP/0/0/CPU0:router# show services redundancy summary

  Tue Nov 11 10:08:25.252 PST DST
  Service type      Offline Act Only Act+Stby    Total
  ----------------------------------------------------
  Firewall         00000000 00000001 00000000 00000001
  SBC              00000000 00000001 00000000 00000001
  IPSec            00000000 00000001 00000000 00000001
  GRE              00000000 00000001 00000000 00000001
  

Related Commands

Command

Description

firewall

Configures a virtual firewall in Cisco IOS XR software.

interface service-gre

Creates a static IPSec-protected generic routing encapsulation (GRE) interface.

interface service-ipsec

Creates a static IPSec virtual interface.

interface vasi

Configures a VASI interface and enters interface configuration mode.

sbc

Configures an SBC instance and enters SBC configuration mode.

service-location

Associates a physical interface with a firewall, SBC, or VASI interface service instance,

show services role

To display the current service role on service cards, use the show services role command in

EXEC

XR EXEC

mode.

show services role [detail] [ location node-id ]

Syntax Description

detail

Displays the reason a role has not been enacted, if applicable.

location node-id

Location for which to display the specified information. The node-id argument is entered in the rack/slot/module notation.

Command Default

No default behavior or values

Command Modes

EXEC

XR EXEC

Command History

Release

Modification

Release 3.5.0

This command was introduced.

Release 5.0.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Operations

interface

read

Examples

This example displays sample output from the show services role command:

RP/0/0RP0RSP0/CPU0:router# show services role
Thu Mar  1 14:53:55.530 PST
Node       Configured Role     Enacted Role        Enabled Services
-----------------------------------------------------------------------------
0/3/CPU0   SESH                SESH                 ServiceInfra 
  

Related Commands

Command

Description

hw-module service offline location

Configures offline mode as the role for a specific node.

show version

To display the configuration of the system hardware, the software version, the names and sources of configuration files, and the boot images, use the show version command in EXEC

XR EXEC

mode.

show version

Syntax Description

This command has no keywords or arguments.

Command Default

No default behavior or values

Command Modes

EXEC

XR EXEC

Command History

Release

Modification

Release 2.0

This command was introduced.

Release 5.0.0

This command was introduced.

Release 3.2

This command was introduced.

Release 3.3.0

The show version command was moved from the sysmgr task ID to the basic-services task ID.

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The show version command displays a variety of system information, including hardware and software version, router uptime, boot settings (configuration register), and active software.

Task ID

Task ID

Operations

basic-services

read

Examples

This example shows partial output from the show version command:

Cisco IOS XR Software, Version 5.0.0
Copyright (c) 2013 by Cisco Systems, Inc.

Build Information:
 Built By     : palwal
 Built On     : Wed Sep 18 11:49:11 PDT 2013
 Build Host   : iox-bld4
 Workspace    : /auto/srcarchive8/production/5.0.0/all/workspace
 Version      : 5.0.0
 Location     : /opt/cisco/XR/packages/

System uptime is 1 day, 1 hour, 24 minutes
RP/0/0RP0RSP0/CPU0:router# show version
  
  Cisco IOS XR Software, Version 3.4.0
  Copyright (c) 2006 by cisco Systems, Inc.
  
  ROM: System Bootstrap, Version 1.32(20050525:193559) [CRS-1 ROMMON],
  
  CRS-8_P1 uptime is 1 week, 22 hours, 27 minutes
  System image file is "disk0:hfr-os-mbi-3.3.90/mbihfr-rp.vm"
  
  cisco CRS-8/S (7457) processor with 4194304K bytes of memory.
  7457 processor at 1197Mhz, Revision 1.2
  
  16 Packet over SONET/SDH network interface(s)
  16 SONET/SDH Port controller(s)
  2 Ethernet/IEEE 802.3 interface(s)
  16 GigabitEthernet/IEEE 802.3 interface(s)
  2043k bytes of non-volatile configuration memory.
  38079M bytes of hard disk.
  1000592k bytes of ATA PCMCIA card at disk 0 (Sector size 512 bytes).
  1000640k bytes of ATA PCMCIA card at disk 1 (Sector size 512 bytes).
  
  Package active on node 0/1/SP:
  hfr-diags, V 3.3.90[1I], Cisco Systems, at disk0:hfr-diags-3.3.90
      Built on Mon Mar 27 12:29:00 UTC 2006
      By edde-bld1 in /vws/aga/production/3.3.90.1I/hfr/workspace for c2.95.3-p8
  
  hfr-admin, V 3.3.90[1I], Cisco Systems, at disk0:hfr-admin-3.3.90
      Built on Mon Mar 27 09:22:26 UTC 2006
      By edde-bld1 in /vws/aga/production/3.3.90.1I/hfr/workspace for c2.95.3-p8
  
  hfr-base, V 3.3.90[1I], Cisco Systems, at disk0:hfr-base-3.3.90
      Built on Mon Mar 27 09:13:04 UTC 2006
      By edde-bld1 in /vws/aga/production/3.3.90.1I/hfr/workspace for c2.95.3-p8
  
  hfr-os-mbi, V 3.3.90[1I], Cisco Systems, at disk0:hfr-os-mbi-3.3.90
      Built on Mon Mar 27 08:34:13 UTC 2006
      By edde-bld1 in /vws/aga/production/3.3.90.1I/hfr/workspace for c2.95.3-p8
  --More--
    
RP/0/0RP0RSP0/CPU0:router# show version

Tue Jul 28 05:14:13.670 DST

Cisco IOS XR Software, Version 3.9.0.14I
Copyright (c) 2009 by Cisco Systems, Inc.

ROM: System Bootstrap, Version 1.1(20090521:183759) [ASR9K ROMMON],  

PE44_ASR-9010 uptime is 1 week, 6 days, 13 hours, 52 minutes
System image file is "bootflash:disk0/asr9k-os-mbi-3.9.0.14I/mbiasr9k-rp.vm"

cisco ASR9K Series (MPC8641D) processor with 4194304K bytes of memory.
MPC8641D processor at 1333MHz, Revision 2.2

2 Management Ethernet
12 TenGigE
40 GigabitEthernet
219k bytes of non-volatile configuration memory.
975M bytes of compact flash card.
33994M bytes of hard disk.
1605616k bytes of disk0: (Sector size 512 bytes).
1605616k bytes of disk1: (Sector size 512 bytes).

Configuration register on node 0/RSP0/CPU0 is 0x102
Boot device on node 0/RSP0/CPU0 is disk0:
Package active on node 0/RSP0/CPU0:
asr9k-scfclient, V 3.9.0.14I, Cisco Systems, at disk0:asr9k-scfclient-3.9.0.14I
    Built on Mon Jul 13 08:28:45 DST 2009
    By sjc-lds-208 in /auto/ioxbuild7/production/3.9.0.14I/asr9k/workspace for c4.2.1-p0

asr9k-adv-video, V 3.9.0.14I, Cisco Systems, at disk0:asr9k-adv-video-3.9.0.14I
    Built on Mon Jul 13 10:13:23 DST 2009
    By sjc-lds-208 in /auto/ioxbuild7/production/3.9.0.14I/asr9k/workspace for c4.2.1-p0

asr9k-fpd, V 3.9.0.14I, Cisco Systems, at disk0:asr9k-fpd-3.9.0.14I
    Built on Mon Jul 13 08:44:47 DST 2009
    By sjc-lds-208 in /auto/ioxbuild7/production/3.9.0.14I/asr9k/workspace for c4.2.1-p0

asr9k-diags, V 3.9.0.14I, Cisco Systems, at disk0:asr9k-diags-3.9.0.14I
    Built on Mon Jul 13 08:28:48 DST 2009
    By sjc-lds-208 in /auto/ioxbuild7/production/3.9.0.14I/asr9k/workspace for c4.2.1-p0

asr9k-k9sec, V 3.9.0.14I, Cisco Systems, at disk0:asr9k-k9sec-3.9.0.14I
    Built on Mon Jul 13 08:43:40 DST 2009
    By sjc-lds-208 in /auto/ioxbuild7/production/3.9.0.14I/asr9k/workspace for c4.2.1-p0

asr9k-mgbl, V 3.9.0.14I, Cisco Systems, at disk0:asr9k-mgbl-3.9.0.14I
    Built on Mon Jul 13 10:11:41 DST 2009
    By sjc-lds-208 in /auto/ioxbuild7/production/3.9.0.14I/asr9k/workspace for c4.2.1-p0

asr9k-mcast, V 3.9.0.14I, Cisco Systems, at disk0:asr9k-mcast-3.9.0.14I
    Built on Mon Jul 13 08:40:57 DST 2009
    By sjc-lds-208 in /auto/ioxbuild7/production/3.9.0.14I/asr9k/workspace for c4.2.1-p0

 --More--
               
RP/0/5/CPU0:router# show version

Thu Feb 19 14:31:51.061 PST DST

Cisco IOS XR Software, Version 3.8.0.30I[SIT_IMAGE]
Copyright (c) 2009 by Cisco Systems, Inc.

ROM: System Bootstrap, Version 12.0(20051020:160303) [sjabbar-CSCsa64979_4 1.17dev(0.5)] DEVELOPMENT SOFTWARE
Copyright (c) 1994-2005 by cisco Systems,  Inc.

PE21_C12406 uptime is 1 week, 2 days, 13 hours, 46 minutes
System image file is "disk0:c12k-os-mbi-3.8.0.30I/mbiprp-rp.vm"

cisco 12406/PRP (7457) processor with 2097152K bytes of memory.
7457 processor at 1266Mhz, Revision 1.2

2 Cisco 12000 Series - Multi-Service Blade Controllers
2 Cisco 12000 Series SPA Interface Processor-601/501/401
1 Cisco 12000 Series Performance Route Processor
3 Management Ethernet
8 PLIM_QOS
6 T3
6 SONET/SDH
6 Packet over SONET/SDH
2 GigabitEthernet/IEEE 802.3 interface(s)
28 T1
2 Asynchronous Transfer Mode
3 ATM network sub-interface(s)
10 VLAN sub-interface(s)
4 Serial network interface(s)
8 FastEthernet
2 FR point-to-point sub interface
1018k bytes of non-volatile configuration memory.
800560k bytes of disk0: (Sector size 512 bytes).
800560k bytes of disk1: (Sector size 512 bytes).
65536k bytes of Flash internal SIMM (Sector size 256k).

Boot device on node 0/0/CPU0 is mem:
Package active on node 0/0/CPU0:
c12k-sbc, V 3.8.0.30I[SIT_IMAGE], Cisco Systems, at disk0:c12k-sbc-3.8.0.30I
    Built on Mon Feb  2 10:10:13 PST 2009
    By sjc-lds-364 in /auto/ioxbuild5/production/3.8.0.30I.SIT_IMAGE/c12k/workspace for c4.2.1-p0

c12k-ipsec-service, V 3.8.0.30I[SIT_IMAGE], Cisco Systems, at disk0:c12k-ipsec-service-3.8.0.30I
    Built on Mon Feb  2 08:38:02 PST 2009
    By sjc-lds-364 in /auto/ioxbuild5/production/3.8.0.30I.SIT_IMAGE/c12k/workspace for c4.2.1-p0
 --More--
               
Table 22  show version Field Descriptions

Field

Description

Cisco IOS XR Software, Version #

Cisco IOS XR software version number currently running on the router.

ROM

System bootstrap version number currently running on the router.

router uptime

Number of uninterrupted days, hours, minutes, and seconds the system has been up and running.

System image file is

Location and name of the system image file currently running on the router.

Packet over SONET/SDH network interface(s)

Number of Packet-over-SONET/SDH interfaces available on the current router.

SONET/SDH Port controller(s)

Number of SONET or SDH1 interfaces available on the current router.

Ethernet/IEEE 802.3 interface(s)

Number of Ethernet or IEEE 802.3 interfaces available on the current router.

GigabitEthernet/IEEE interface(s)

Number of Gigabit Ethernet or IEEE 802.3 interfaces available on the current router.

bytes of non-volatile configuration memory

Available volatile configuration memory, in bytes.

bytes of ATA PCMCIA card at disk 0

ATA PCMCIA2 available on the card in disk 0, in bytes.

Package active on node 0/1/SP

Details about the current software package that is running on the SP node in slot 1.

1 SDH = Synchronous Digital Hierarchy
2 ATA PCMCIA = AT Attachment Personal Computer Memory Card Industry Association

show upgrade

To display information regarding the current fabric downloader, mbus ROM and ROM monitor images, including whether or not an upgrade is required, use the show upgrade command in administration EXEC mode.

show upgrade { all | fabric-downloader | mbus-rom | rommon } location { all | node-id }

Syntax Description

all

Displays upgrade information regarding all hardware-related images.

fabric-downloader

Displays upgrade information regarding the fabric downloader image.

mbus-rom

Displays upgrade information regarding the MBus ROM agent image.

rommon

Displays upgrade information regarding the ROM monitor image.

location all

Displays upgrade information for all cards in the router.

location node-id

Displays upgrade information for a specific node. The node-id is expressed in the rack/slot/module notation.

Note   

Enter the show platform command to see the location of all nodes installed in the router.

Command Default

None

Command Modes

Administration EXEC

Command History

Release Modification
Release 3.9.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation
sysmgr

read

Examples

This example illustrates sample output from the show upgrade command with the all keyword:


RP/0/0/CPU0:router(admin)# show upgrade all location all

Wed Jan 28 19:59:26.373 UTC 
Node          Type                PLIM              Fab-Dwnldr    Mbus-Rom     Rommon
                                                     Upgrade      Upgrade      Upgrade
                                                     Required     Required     Required
---------------------------------------------------------------------------------------
0/0/CPU0      PRP(Active)         N/A               N/A           Yes          Yes
0/1/CPU0      L3LC Eng 5+         Jacket Card       No            Yes          No
0/2/CPU0      L3LC Eng 5+         Jacket Card       Yes           Yes          No
0/3/CPU0      L3LC Eng 5+         Jacket Card       Yes           Yes          No
0/4/CPU0      L3 Service Eng      N/A               Yes           Yes          No
0/5/CPU0      L3LC Eng 5+         Jacket Card       No            Yes          No
0/6/CPU0      L3LC Eng 5          Jacket Card       Yes           Yes          No
0/7/CPU0      L3LC Eng 3          OC12-ATM-4        No            Yes          No
0/8/CPU0      PRP(Standby)        N/A               N/A           Yes          Yes
0/9/CPU0      L3LC Eng 3          OC3-POS-4         No            Yes          No
0/16/CPU0     CSC10               N/A               N/A           Yes          N/A
0/17/CPU0     CSC10(P)            N/A               N/A           Yes          N/A
0/18/CPU0     SFC10               N/A               N/A           Yes          N/A
0/19/CPU0     SFC10               N/A               N/A           Yes          N/A
0/20/CPU0     SFC10               N/A               N/A           Yes          N/A
0/21/CPU0     SFC10               N/A               N/A           Yes          N/A
0/22/CPU0     SFC10               N/A               N/A           Yes          N/A
0/24/CPU0     ALARM10             N/A               N/A           Yes          N/A
0/25/CPU0     ALARM10             N/A               N/A           Yes          N/A
0/29/CPU0     GSR16-BLOWER        N/A               N/A           Yes          N/A
  

This example illustrates sample output from the show upgrade command with the fabric-downloader keyword.

RP/0/0/CPU0:router(admin)# show upgrade fabric-downloader location all

Wed Jan 28 19:59:46.550 UTC 
Node        Type              PLIM              Current         Image           Upgrade
                                                Fab Downloader  Fab Downloader  Required
                                                Version         Version
----------------------------------------------------------------------------------------
0/0/CPU0    PRP(Active)       N/A               N/A             N/A             N/A
0/1/CPU0    L3LC Eng 5+       Jacket Card       4.7             4.7             No
0/2/CPU0    L3LC Eng 5+       Jacket Card       4.5             4.7             Yes
0/3/CPU0    L3LC Eng 5+       Jacket Card       4.5             4.7             Yes
0/4/CPU0    L3 Service Eng    N/A               3.1             3.2             Yes
0/5/CPU0    L3LC Eng 5+       Jacket Card       4.7             4.7             No
0/6/CPU0    L3LC Eng 5        Jacket Card       4.5             4.7             Yes
0/7/CPU0    L3LC Eng 3        OC12-ATM-4        8.0             8.0             No
0/8/CPU0    PRP(Standby)      N/A               N/A             N/A             N/A
0/9/CPU0    L3LC Eng 3        OC3-POS-4         8.0             8.0             No
0/16/CPU0   CSC10             N/A               N/A             N/A             N/A
0/17/CPU0   CSC10(P)          N/A               N/A             N/A             N/A
0/18/CPU0   SFC10             N/A               N/A             N/A             N/A
0/19/CPU0   SFC10             N/A               N/A             N/A             N/A
0/20/CPU0   SFC10             N/A               N/A             N/A             N/A
0/21/CPU0   SFC10             N/A               N/A             N/A             N/A
0/22/CPU0   SFC10             N/A               N/A             N/A             N/A
0/24/CPU0   ALARM10           N/A               N/A             N/A             N/A
0/25/CPU0   ALARM10           N/A               N/A             N/A             N/A
0/29/CPU0   GSR16-BLOWER      N/A               N/A             N/A             N/A
  

This example illustrates sample output from the show upgrade command with the mbus-rom keyword:

RP/0/0/CPU0:router(admin)# show upgrade mbus-rom location all

Wed Jan 28 19:59:36.599 UTC 
Node        Type              PLIM            Current      Image       Upgrade
                                              Mbus Rom     Mbus Rom    Required
                                              Version      Version
-------------------------------------------------------------------------------
0/0/CPU0    PRP(Active)       N/A             3.54         4.4         Yes
0/1/CPU0    L3LC Eng 5+       Jacket Card     4.2          4.4         Yes
0/2/CPU0    L3LC Eng 5+       Jacket Card     3.51         4.4         Yes
0/3/CPU0    L3LC Eng 5+       Jacket Card     3.46         4.4         Yes
0/4/CPU0    L3 Service Eng    N/A             3.3          4.4         Yes
0/5/CPU0    L3LC Eng 5+       Jacket Card     3.54         4.4         Yes
0/6/CPU0    L3LC Eng 5        Jacket Card     3.46         4.4         Yes
0/7/CPU0    L3LC Eng 3        OC12-ATM-4      3.54         4.4         Yes
0/8/CPU0    PRP(Standby)      N/A             3.46         4.4         Yes
0/9/CPU0    L3LC Eng 3        OC3-POS-4       3.46         4.4         Yes
0/16/CPU0   CSC10             N/A             3.53         4.4         Yes
0/17/CPU0   CSC10(P)          N/A             3.53         4.4         Yes
0/18/CPU0   SFC10             N/A             3.46         4.4         Yes
0/19/CPU0   SFC10             N/A             3.46         4.4         Yes
0/20/CPU0   SFC10             N/A             3.46         4.4         Yes
0/21/CPU0   SFC10             N/A             3.46         4.4         Yes
0/22/CPU0   SFC10             N/A             3.46         4.4         Yes
0/24/CPU0   ALARM10           N/A             3.46         4.4         Yes
0/25/CPU0   ALARM10           N/A             3.46         4.4         Yes
0/29/CPU0   GSR16-BLOWER      N/A             3.46         4.4         Yes
  

This example illustrates sample output from the show upgrade command with the rommon keyword:

RP/0/0/CPU0:router(admin)# show upgrade rommon location all
           
Wed Jan 28 19:59:57.839 UTC 
Node      Type              PLIM            Current     Image      Upgrade
                                            Rommon      Rommon     Required
                                            Version     Version
-----------------------------------------------------------------------------
0/0/CPU0  PRP(Active)       N/A             1.17        1.20       Yes
0/1/CPU0  L3LC Eng 5+       Jacket Card     17.1        17.1       No
0/2/CPU0  L3LC Eng 5+       Jacket Card     17.1        17.1       No
0/3/CPU0  L3LC Eng 5+       Jacket Card     17.1        17.1       No
0/4/CPU0  L3 Service Eng    N/A             1.3         1.3        No
0/5/CPU0  L3LC Eng 5+       Jacket Card     19.0        17.1       No
0/6/CPU0  L3LC Eng 5        Jacket Card     17.1        17.1       No
0/7/CPU0  L3LC Eng 3        OC12-ATM-4      17.1        17.1       No
0/8/CPU0  PRP(Standby)      N/A             1.18        1.20       Yes
0/9/CPU0  L3LC Eng 3        OC3-POS-4       17.1        17.1       No
0/16/CPU0 CSC10             N/A             N/A         N/A        N/A
0/17/CPU0 CSC10(P)          N/A             N/A         N/A        N/A
0/18/CPU0 SFC10             N/A             N/A         N/A        N/A
0/19/CPU0 FC10              N/A             N/A         N/A        N/A
0/20/CPU0 SFC10             N/A             N/A         N/A        N/A
0/21/CPU0 SFC10             N/A             N/A         N/A        N/A
0/22/CPU0 SFC10             N/A             N/A         N/A        N/A
0/24/CPU0 ALARM10           N/A             N/A         N/A        N/A
0/25/CPU0 ALARM10           N/A             N/A         N/A        N/A
0/29/CPU0 GSR16-BLOWER      N/A             N/A         N/A        N/A
  

Related Commands

Command

Description

upgrade all

Upgrades the fabric downloader, ROM Monitor, Mbus and FPD image package on a module.  

upgrade fabric-downloader

Upgrades the fabric downloader image package on a module.  

upgrade mbus

Upgrades the Mbus agent ROM image on a module.  

upgrade all

To upgrade the fabric downloader, ROMMON, Mbus, and current field-programmable device (FPD) image package on a module or on all modules installed in a router, use the upgrade all command in administration EXEC mode.

upgrade all location { node-id | all } [force]

Syntax Description

location{node-id | all}

Specifies the nodes for which to upgrade the images. The node-id argument is expressed in the rack/slot/module notation. Use the all keyword to indicate all nodes.

force

Skips the version check and forces an upgrade.

Command Default

No default behavior or values

Command Modes

Administration EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

sysmgr

read, write

Examples

The following example shows how to upgrade all images on all line cards that are installed in the router:

RP/0/0/CPU0:Router# admin
RP/0/0/CPU0:router(admin)# upgrade all location all
         

Related Commands

Command

Description

clear mbus-statistics location

Clears all Mbus interface counters on a specific node.

show mbus

Displays Mbus CAN errors and interface counters.

show platform

Displays information and status for each node in the system.

upgrade bsl

To upgrade the bootstrap loader on the PRP-3, use the upgrade bsl command in administration EXEC mode.

upgrade bsl location { all | node-id }

Syntax Description

location all

Upgrades the bootstrap loader on all RPs in the router.

location node-id

Upgrades the bootstrap loader on a specific RP. The node-id argument is expressed in the rack/slot/module notation.

Command Default

None

Command Modes

Administration EXEC

Command History

Release Modification
Release 3.9.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The upgrade bsl command upgrades the bootstrap loader (BSL) firmware on the PRP-3 board. When the PRP-3 is powered up or reloaded, the BSL is the firmware that is responsible for the minimal initialization of the PRP-3 hardware and the launching of the ROM monitor firmware.

Task ID

Task ID Operation
sysmgr

read, write

Examples


Related Commands

upgrade cpuctrlbits

To upgrade the CPU controller bits on all nodes that are installed in the router or on a specific node, use the upgrade cpuctrlbits command in administration EXEC mode.

upgrade cpuctrlbits { all | location node-id } [ bootflash | disk0 | disk1 | internal ]

Syntax Description

all

Upgrades the CPU controller bits on all nodes installed in the router.

location node-id

Upgrades the CPU controller bits on a specific node. The node-id is expressed in the rack/slot/module notation.

Note   

Enter the show platform command to see the location of all nodes installed in the router.

bootflash

(Optional) Uses the images located on the bootflash to upgrade the CPU controller on all nodes, or on the specified node.

disk0

(Optional) Uses the images located on disk0 to upgrade the CPU controller on all nodes, or on the specified node.

disk1

(Optional) Uses the images located on disk1 to upgrade the CPU controller on all nodes, or on the specified node.

internal

(Optional) Uses the images located in the /pkg/bin.

Note   

This is the default location for the ROMMON image.

Command Default

Default location for the ROMMON image: internal

Command Modes

Administration EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Release 3.3.0

The upgrade cpuctrlbits command was moved from the sysmgr task ID to the system task ID.

Release 3.4.0

No modification.

Release 3.5.0

No modification.

Release 3.6.0

No modification.

Release 3.7.0

No modification.

Release 3.8.0

No modification.

Release 3.9.0

No modification.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The upgrade cpuctrlbits command is only applicable to boards that use the Squid CPU controller, and not the Squirt controller. Use the internal keyword to determine which CPU controller is used in a specific card, as indicated in bold in the following example:

RP/0/RP0/CPU0:router# show controller cpuctrl internal
  
Cpuctrl Internal Info for node 0/1/CPU0:
          Error Interrupts = 0    Spurious Error Interrupts = 0
          PCI Error Overflows = 0         PCI PM Error Overflows = 0
          PCIX Error Overflows = 0        Internal Access PCI Overflows = 0
          Port Error Overflows = 0        Error Log Overflows = 0
          cpuctrl Config Reg = 0x8357ffff  cpuctrl Physical Offset = 0x80000000
          cpuctrl Window Size = 0x40000000 cpuctrl Port Window Size = 0x04000000
          cpuctrl SHMem Size = 0x00800000  cpuctrl SHMem Used = 0x00224fb0
          cpuctrl version info: Squid FPGA v2.07 Fri Jan 23 16:21:01 2004 ykoren
  
  Cpuctrl Internal Info for node 0/4/CPU0:
          Error Interrupts = 0    Spurious Error Interrupts = 0
          PCI Error Overflows = 0         PCI PM Error Overflows = 0
          PCIX Error Overflows = 0        Internal Access PCI Overflows = 0
          Port Error Overflows = 0        Error Log Overflows = 0
          cpuctrl Config Reg = 0xffffffff  cpuctrl Physical Offset = 0x80000000
          cpuctrl Window Size = 0x40000000 cpuctrl Port Window Size = 0x04000000
          cpuctrl SHMem Size = 0x00800000  cpuctrl SHMem Used = 0x00224fb0
          cpuctrl version info: SQUIRT v3
  .
  .
  .
  

Task ID

Task ID

Operations

system

read, write

Examples

This example shows how to upgrade the CPU controller bits on all nodes in a router:

RP/0/RP0/CPU0:router# admin
RP/0/RP0/CPU0:router(admin)# upgrade cpucrtlbits all
  
  Please do not power cycle, reload the router or reset any nodes until
   all upgrades are completed.
  Please check the syslog to make sure that all nodes are upgraded successfully.
  If you need to perform multiple upgrades, please wait for current upgrade
   to be completed before proceeding to another upgrade.
  Failure to do so may render the cards under upgrade to be unusable.
  

Related Commands

Command

Description

show controller cpuctrl internal

Displays information about the internal CPU controller in the cards in the router.

show platform

Displays information and status for each node in the system.

upgrade fabric-downloader

To upgrade the fabric downloader image package on a module or on all modules installed in a router, use the upgrade fabric-downloader command in administration EXEC mode.

upgrade fabric-downloader location { node-id | all } [force]

Syntax Description

location{node-id | all}

Specifies the node for which to upgrade the fabric downloader. The node-id argument is expressed in the rack/slot/module notation. Use the all keyword to indicate all nodes.

Note   

Enter the show platform command to see the location of all nodes installed in the router.

force

Skips the version check and forces an upgrade.

Command Default

No default behavior or values

Command Modes

Administration EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

sysmgr

read, write

Examples

This example shows how to upgrade the fabric-downloader image package on a specific node:

RP/0/0/CPU0:router# admin
RP/0/0/CPU0:router(admin)# upgrade fabric-downloader location 0/0/CPU0 
         

Related Commands

Command

Description

show platform

Displays information and status for each node in the system.

upgrade hw-module fpd

To manually upgrade the current field-programmable device (FPD) image package on a module, use the upgrade hw-module fpd command in System Admin EXEC administration EXEC mode.

upgrade hw-module fpd { all | fabldr | fpga-type | rommon } [ force ] location [ node-id | all ]

upgrade hw-module fpd { all | fabldr | fpga-type | rommon } [ force ] location [ node-id | all ] [reload]

upgrade hw-module location { node-id | all } fpd { fpd-type | all } [force]

Syntax Description

all

Upgrades all FPD images on the selected module.

fabldr

Upgrades the fabric-downloader FPD image on the module.

fpga-type

Upgrades a specific field-programmable gate array (FPGA) image on the module. Use the show fpd package command to view all available FPGA images available for a specific module.

rommon

Upgrades the ROMMON image on the module.

force

(Optional) Forces the update of the indicated FPD image package on a shared port adapter (SPA) that meets the minimum version requirements. Without this option, the manual upgrade upgrades only incompatible FPD images.

location {node-id |all}

Specifies the node for which to upgrade the FPD image. The node-id argument is expressed in the rack/slot/subslot notation. Use the all keyword to indicate all nodes.

reload

Reloads the module after the FPD image has been updated. If you do not use the reload keyword, you must manually reload the module before the FPD upgrade is complete. Use the hw-module reset or hw-module subslot reload command in EXEC mode to reload the module.

Command Default

None

Command Modes

Administration EXEC

System Admin EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Release 3.3.0

The reload keyword was added to this command.

Support for multiple FPGA images was added.

Release 3.7.2

This command was introduced.

Release 5.0.0

This command was introduced.

Usage Guidelines


Note


The use of the force option when doing a fpd upgrade is not recommended except under explicit direction from Cisco engineering or TAC.


During the upgrade procedure, the module must be offline (shut down but powered).

Naming notation for the node-id argument is rack/slot/subslot; a slash between values is required as part of the notation.

  • rack —Chassis number of the rack.

  • slot —Physical slot number of the SPA interface processor (SIP).

  • subslot —Subslot number of the SPA.

For more information about the syntax for the router, use the question mark (?) online help function.

When you start the FPD upgrade procedure or log into a router that is running the FPD upgrade procedure, the following message is displayed to the screen on TTY, console and AUX ports:
FPD upgrade in progress on some hardware, reload/configuration change on those 
is not recommended as it might cause HW programming failure and result in RMA 
of the hardware.

 
If you enter administration mode while the FPD upgrade procedure is running, the following message is displayed to the screen on TTY, console and AUX ports:
FPD upgrade in progress on some hardware, reload/configuration change on those 
is not recommended as it might cause HW programming failure and result in RMA 
of the hardware. Do you want to continue? [Confirm (y/n)]

 
If you enter global configuration mode while the FPD upgrade procedure is running, the following message is displayed to the screen on TTY, console and AUX ports:
FPD upgrade in progress on some hardware, configuration change on those is not 
recommended as it might cause HW programming failure and result in RMA of the 
hardware. Do you want to continue? [Confirm (y/n)]

 
When the FPD upgrade global timer expires, the following warning message displayed to the screen.
FPD upgrade has exceeded the maximum time window, the process will terminate now. 
Please check the status of the hardware and reissue the upgrade command if required.

 

If a PRP switchover occurs while an FPD upgrade is running, the following message is dislayed to the screen:

FPD upgrade failed due to RP FO, FPGA upgrade may be in indeterminate state. 
Please reissue the FPD upgrade command.
 
 

Task ID

Task ID

Operations

system

read, write

sysmgr

read, write

Examples

The following example shows how to upgrade the default FPGA on a SPA:


RP/0/0RP0RSP0/CPU0:router# admin
RP/0/0RP0RSP0/CPU0:router(admin)# upgrade hw-module fpd fpga location 0/1/4

% RELOAD REMINDER:
  - The upgrade operation of the target module will not interrupt its normal
    operation. However, for the changes to take effect, the target module
    will need to be manually reloaded after the upgrade operation. This can
    be accomplished with the use of "hw-module <target> reload" command.
  - If automatic reload operation is desired after the upgrade, please use
    the "reload" option at the end of the upgrade command.
  - The output of "show hw-module fpd location" command will not display
    correct version information after the upgrade if the target module is
    not reloaded.
Continue? [confirm] y
  
SP/0/1/SP:Dec 22 05:41:17.920 : upgrade_daemon[125]: programming...with file 
/net/node0_RP1_CPU0/c12khfrasr9k-lc-3.3.83/fpd/ucode/fpga_gladiator_sw0.6.xsvf
SP/0/1/SP:Dec 22 05:41:28.900 : upgrade_daemon[125]: ...programming...
SP/0/1/SP:Dec 22 05:41:28.906 : upgrade_daemon[125]: ...it will take a while...
SP/0/1/SP:Dec 22 05:41:29.004 : upgrade_daemon[125]: ...it will take a while...
SP/0/1/SP:Dec 22 05:43:03.432 : upgrade_daemon[125]: ...programming...
SP/0/1/SP:Dec 22 05:43:03.438 : upgrade_daemon[125]: ...it will take a while...
Successfully upgraded spa fpga instance 4 on location 0/1/4.
  

RP/0/0/CPU0:Router# admin
RP/0/0/CPU0:Router(admin)# upgrade hw-module fpd fpga location 0/3/0

% RELOAD REMINDER:
  - The upgrade operation of the target module will not interrupt its normal
    operation. However, for the changes to take effect, the target module
    will need to be manually reloaded after the upgrade operation. This can
    be accomplished with the use of "hw-module <target> reload" command.
  - If automatic reload operation is desired after the upgrade, please use
    the "reload" option at the end of the upgrade command.
  - The output of "show hw-module fpd location" command will not display
    correct version information after the upgrade if the target module is
    not reloaded.
Continue? [confirm] y
  
LC/0/3/CPU0:Dec 22 06:46:59.732 : spa_192_jacket_v2[203]: %SPA_FPD-6-UPDATE_START :
SPA-4XCT3/DS0[0]: Starting update of FPD 'fpga' image
LC/0/3/CPU0:Dec 22 06:47:23.518 : spa_192_jacket_v2[203]: %SPA_FPD-6-UPDATE_PASSED :
SPA-4XCT3/DS0[0]: Successfully updated FPD 'fpga' image
Successfully upgraded spa fpga instance 0 on location 0/3/0.
  
This example shows how to upgrade the Ethernet Switch and view the output using the show hw-module fpd command:
sysadmin-vm:0_RP0# upgrade hw-module location 0/RP0 fpd Ethernet
sysadmin-vm:0_RP0# show hw-module fpd
Tue Aug  27 14:54:10.200 UTC
                                                                  FPD Versions
                                                               ================
Location      Card type     HWver   FPD device       Status    Running Download
-------------------------------------------------------------------------------
0/0           NC6-10X100G-M 0.2     CCC FPGA         READY       1.14    1.14
0/0           NC6-10X100G-M 0.2     BAO-MB FPGA      READY       1.00    1.00
0/0           NC6-10X100G-M 0.2     CCC Power-On     READY       1.30    1.30
0/0           NC6-10X100G-M 0.2     Ethernet Switch  READY       1.32    1.32
0/0           NC6-10X100G-M 0.2     BIOS FPD         READY       9.10    9.10
0/0           NC6-10X100G-M 1.0     Slice-1 GN2411   READY       2.07    2.07
0/1           NC6-10X100G-M 0.2     CCC FPGA         READY       1.14    1.14
0/1           NC6-10X100G-M 0.2     BAO-MB FPGA      READY       1.00    1.00
0/1           NC6-10X100G-M 0.2     CCC Power-On     READY       1.30    1.30
0/1           NC6-10X100G-M 0.2     Ethernet Switch  READY       1.32    1.32
0/1           NC6-10X100G-M 0.2     BIOS FPD         READY       9.10    9.10
0/1           NC6-10X100G-M 1.0     Slice-1 GN2411   READY       2.07    2.07
0/RP0         NC6-RP        0.1     CCC FPGA         UPGD SKIP   1.00    1.00
0/RP0         NC6-RP        0.1     CCC Power-On     UPGD SKIP   1.30    1.30
0/RP0         NC6-RP        0.1     Ethernet Switch  UPGD SKIP   1.32    1.32
0/RP0         NC6-RP        0.1     CPU Complex FPD  UPGD SKIP   3.06    3.06
0/RP0         NC6-RP        0.1     BIOS FPD         UPGD SKIP   9.10    9.10
0/RP1         NC6-RP        0.1     CCC FPGA         READY       1.00    1.00
0/RP1         NC6-RP        0.1     CCC Power-On     READY       1.30    1.30

Related Commands

Command

Description

show fpd package

Displays which SPAs and SIPs are supported with your current Cisco IOS XR software release, which FPD image you need for each card, and what the minimum hardware requirements are for the various modules.

show hw-module fpd

Displays field-programmable device (FPD) compatibility for all modules or a specific module.

upgrade mbus

To upgrade the Mbus agent ROM image on a module or on all modules installed in a router, use the upgrade mbus command in administration EXEC mode.

upgrade mbus [force] location { node-id | all }

Syntax Description

force

Skips the version check and forces an upgrade.

location {node-id | all}

Specifies the node for which to upgrade the Mbus agent ROM. The node-id argument is expressed in the rack/slot/module notation. Use the all keyword to indicate all nodes.

Enter the show platform command to see the location of all nodes installed in the router.

Command Default

No default behavior or values

Command Modes

Administration EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

sysmgr

read, write

Examples

This example shows how to upgrade the Mbus agent ROM on a specific node:

RP/0/0/CPU0:router# admin
RP/0/0/CPU0:router(admin)# upgrade mbus location 0/0/CPU0 
  
Upgrading the MBUS agent rom on slot 0
RP/0/0/CPU0:Nov 18 16:52:23.296 : upgrade_mbus[65703]: %MBUS-6-API_INFO_DUMP : 
 download status slot 0, DOWNLOAD_SUCCESS
RP/0/0/CPU0:Nov 18 16:52:33.422 : upgrade_mbus[65703]: %MBUS-6-API_INFO_DUMP :  
 download status slot 0, PROGRAM_ROM SUCCESS
Upgrade complete.  Use admin CLI "test mbus soft-reset-agent" or OIR the card 
 to force new MBUS Rom image to execute.
    

Related Commands

Command

Description

clear mbus-statistics location

Clears all Mbus interface counters on a specific node.

show mbus

Displays Mbus CAN errors and interface counters.

show platform

Displays information and status for each node in the system.

upgrade rommon

To upgrade the ROMMON image on a module or on all modules installed in the router, use the upgrade rommon command in administration EXEC mode.

upgrade rommon location { all | node-id } [force]

Syntax Description

location node-id

Upgrades the ROMMON on a specific line card. The node-id is expressed in the rack/slot/module notation.

Note   

Enter the show platform command to see the location of all nodes installed in the router.

location all

Upgrades the ROMMON on all modules installed in a router.

force

(Optional) Skips the version check and forces an upgrade.

Command Default

None

Command Modes

Administration EXEC

Command History

Release

Modification

Release 3.2

This command was introduced.

Release 3.3.0

No modification.

Release 3.4.0

No modification.

Release 3.5.0

No modification.

Release 3.6.0

No modification.

Release 3.7.0

No modification.

Release 3.8.0

No modification.

Release 3.9.0

No modification.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID Operation
sysmgr

read, write

Examples

This example shows how to upgrade the ROMMON image on a specific node:

RP/0/0/CPU0:router# admin
RP/0/0/CPU0:router(admin)# upgrade rommon location 0/4/CPU0

========= Line Card (Slot 4) =========
Upgrading linecard rom-monitor
Erasing sectors: eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee
Programming image: ppppppppp
Verifying image: vvvvvvvvv
Upgraded linecard rom-monitor successfully
  

Related Commands

Command

Description

show platform

Displays information and status for each node in the system.