Cisco ASR 9000 Series Aggregation Services Router Modular Quality of Service Command Reference, Release 5.1.x
ANCP Commands
Downloads: This chapterpdf (PDF - 1.49MB) The complete bookPDF (PDF - 3.38MB) | Feedback

ANCP Commands

ANCP Commands

This module describes the commands used to configure Access Node Control Protocol (ANCP).

For detailed information regarding ANCP concepts, configuration tasks and examples, see the Configuring ANCP chapter in the Cisco ASR 9000 Series Aggregation Services Router Modular Quality of Service Configuration Guide

ancp

To enable Access Node Control Protocol (ANCP), use the ancp command in global configuration mode. To disable ANCP and delete the ANCP configuration, use the no form of the command.

ancp

no ancp

Syntax Description

This command has no keywords or arguments.

Command Default

Disabled

Command Modes

Global configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

ancp

read, write

Examples

The following example shows how to enable ANCP and enter ANCP configuration mode:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# ancp
RP/0/RSP0/CPU0:router(config-ancp)#

Related Commands

Command

Description

show ancp summary

Displays information about ANCP configuration, including server sender name and neighbor and port counts by state.  

ancp an-port circuit-id

To define a unique access node ID for each access port, use the ancp an-port circuit-id command in the appropriate configuration mode . This information is included in the ANCP Port Up and Port Down messages.

ancp an-port circuit-id Access-Loop-Circuit-Id [ interface type interface-path-id | interface Bundle-Ether bundle-id ]

no ancp an-port circuit-id Access-Loop-Circuit-Id [ interface type interface-path-id | interface Bundle-Ether bundle-id ]

Syntax Description

Access-Loop-Circuit-Id

Unique access loop circuit ID name identifying the access port. Maximum 63 characters.

interface

Describes the access node (AN) port.

type

Interface type:

  • GigabitEthernet (GigabitEthernet/IEEE 802.3 interface)
  • TenGigE (TenGigabitEthernet/IEEE 802.3 interface)

interface-path-id

Physical interface instance. Naming notation is slot / module / port / interface . subinterface .

interface Bundle-Ether

Identifies a Bundle-Ether (Aggregated Ethernet) interface.

bundle-id

Bundle-Ether interface instance. Range is a number from 1 through 65535. Naming notation is interface.subinterface .

Command Default

No default behavior or values

Command Modes

Global configuration

ANCP configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 3.9.0

This command was updated to support the mapping of ANCP ports to VLAN interfaces over Ethernet bundles.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Only subinterfaces of Ethernet and Ethernet bundle interfaces can be mapped to AN ports.

The circuit ID must be supplied before an access node port configuration can be committed.

When using a shared policy instance in subinterfaces with ANCP, the same AN port circuit ID must be mapped to all subinterfaces that have the same shared policy instance.

Circuit ID information can be displayed using the show ancp an-port command.

Task ID

Task ID

Operations

ancp

read, write

Examples

The following example shows a unique access node ID being defined:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# ancp an-port circuit-id circuit1 interface gigabitethernet 2/0/1/1.1

Related Commands

Command

Description

clear ancp an-port

Clears access node (AN) ports of dynamic data or statistics.  

show ancp an-port

Displays data or message statistics referring to individual or multiple Access Node (AN) ports.  

ancp neighbor

To map a neighbor configuration to the respective TCP connection, use the ancp neighbor commanding the appropriate configuration mode. To remove the map, use the no form of the command.

ancp neighbor sender-name { H.H.H | A.B.C.D } { description string | adjacency-timer interval }

no ancp neighbor sender-name { H.H.H | A.B.C.D } { description string | adjacency-timer interval }

Syntax Description

sender-name

ANCP neighbor identification.

H.H.H

MAC address of the sending interface.

A.B.C.D

IP address of the sending interface.

description string

Identifier of ANCP neighbor. General string up to 63 characters.

adjacency-timer interval

The adjacency timer controls the frequency of adjacency protocol messages sourced by the ANCP server. Use the adjacency-timer keyword to define the maximum delay between different stages of ANCP session establishment and the period of ANCP keepalive. The adjacency-timer interval is measured in milliseconds. Replace the interval argument with a number between 100 and 255 (10 to 25.5 seconds). Defaults to 100 ms (10 seconds).

Command Default

Adjacency timer interval default is 10 seconds.

Command Modes

Global configuration

ANCP configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The TCP connection from any neighbor is accepted on any interface that is IP enabled. To match the neighbor configuration to a respective TCP connection, ANCP neighbors are identified by a sender name that must match the corresponding field in adjacency protocol messages.

To configure both description and adjacency-timer parameters, use two separate command lines as shown in the Examples section. If a neighbor session is already established, it resets so that the adjacency timer can take affect.

Task ID

Task ID

Operations

ancp

read, write

Examples

The following example shows how to map a neighbor configuration to its respective connection:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# ancp neighbor sender-name 0001.2222.3333 description VendorA-1 
RP/0/RSP0/CPU0:router(config)# ancp neighbor sender-name 0001.2222.3333 adjacency-timer 20

Related Commands

Command

Description

clear ancp neighbor

Clears the adjacency connection with the neighbor.  

clear ancp summary statistics

Clears aggregate message statistics only, without modifying individual neighbor or port statistics.  

show ancp neighbor

Displays data or message statistics associated with individual ANCP adjacencies or sets of adjacencies.  

show ancp neighbor summary

Displays adjacency counts by state.  

ancp rate-adjustment

To apply a mathematical correction to the ANCP rate update prior to applying it as a shaper rate, use the ancp rate-adjustment command in the appropriate configuration mode. To disable the rate adjustment, use the no form of the command.

ancp rate-adjustment dsl-type access-loop-type percent-factor factor

no ancp rate-adjustment dsl-type access-loop-type percent-factor factor

Syntax Description

dsl-type

Sets DSL type. Possible values are:

adsl1 adsl2 adsl2+ vdsl1 vdsl2 sdsl

access-loop-type

Sets the access loop type, either Ethernet or ATM .

percent-factor factor

Sets the percentage of the ANCP rate. This value should be applied to the ANCP reported rate update prior to configuring it as a shaping rate.

Command Default

No default behavior or values

Command Modes

Global configuration

ANCP configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Both dsl-type and access-loop-type must be specified in order to configure rate adjustment. access-loop-type and dsl-type are compared to appropriate values in optional TLVs in the ANCP Port Up message. The ANCP rate is adjusted by a configured factor in case of a match.

Task ID

Task ID

Operations

ancp

read, write

Examples

The following example shows how to configure a percent factor of 90 with DSL type ADSL2, and an access loop type of Ethernet:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# ancp rate-adjustment adsl2 ethernet percent-factor 90

Related Commands

Command

Description

show ancp summary

Displays information about ANCP configuration, including server sender name and neighbor and port counts by state.  

ancp server sender-name

To configure a local sender name to be used by the ANCP server in adjacency protocol messages toward DSLAMs, use the ancp server sender-name command in the appropriate configuration mode. To return the local sender name to its default value, use the no form of the command.

ancp server sender-name { H.H.H | A.B.C.D }

no ancp server sender-name { H.H.H | A.B.C.D }

Syntax Description

H.H.H

MAC address of the sending interface.

A.B.C.D

IP address of the sending interface.

Command Default

By default, the local sender name is set to the MAC address of a Management Ethernet port.

Command Modes

Global configuration

ANCP configuration

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

ancp

read, write

Examples

The following example shows how to configure a local sender name:

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# ancp server sender-name 0013.1aff.c2bd

Related Commands

Command

Description

show ancp summary

Displays information about ANCP configuration, including server sender name and neighbor and port counts by state.  

clear ancp an-port

To clear access node (AN) ports of dynamic data or statistics, either individually or in groups, use the clear ancp an-port command in EXEC mode.

clear ancp an-port { all | circuit-id Access-Loop-Circuit | interface type interface-path-id | interface Bundle-Ether bundle-id | neighbor { description string | sender-name { H.H.H | A.B.C.D } } } [ statistics ]

Syntax Description

statistics all

Clears dynamic data or statistics on all ports.

circuit-id

A single access node port.

Access-Loop-Circuit-Id

Unique access loop circuit ID name identifying the access port. Maximum 63 characters.

interface

Describes the AN port.

type

Interface type:

  • statistics GigabitEthernet (Gigabit Ethernet/IEEE 802.3 interface)
  • TenGigE (TenGigabitEthernet/IEEE 802.3 interface)

interface-path-id

Physical interface instance. Naming notation is slot/module/port/interface.subinterface .

interface Bundle-Ether

Identifies a Bundle-Ether (Aggregated Ethernet) interface.

bundle-id

Bundle-Ether interface instance. Range is a number from 1 to 65535. Naming notation is interface.subinterface .

neighbor

Access node with an established adjacency with an ANCP server.

description string

Description associated with the ANCP neighbor. General string up to 63 characters.

sender-name

ANCP neighbor identification.

H.H.H

MAC address of the sending interface.

A.B.C.D

IP address of the sending interface.

statistics

(Optional) Resets statistics for the specified set of ports.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 3.9.0

This command was updated to support the mapping of ANCP ports to VLAN interfaces over Ethernet bundles.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Individual ports can be identified by circuit ID or mapped interfaces, as with show commands.

Dynamic data or statistics can be cleared for all ports or for all ports for just a given neighbor.

When used without the statistics keyword, the clear ancp an-port command clears dynamic data, including all rate information, for the selected AN ports. Ports that are not mapped to any local interface are removed from the ANCP port database. When used with the statistics keyword, statistics for the selected ports will be reset.

Task ID

Task ID

Operations

ancp

read, write

Related Commands

Command

Description

clear ancp neighbor

Clears the adjacency connection with the neighbor.  

clear ancp summary statistics

Clears aggregate message statistics only, without modifying individual neighbor or port statistics.  

clear ancp neighbor

To clear the adjacency connection with the neighbor, use the clear ancp neighbor command in EXEC mode.

clear ancp neighbor { all | description string | sender-name { H.H.H | A.B.C.D } } [ state | statistics ]

Syntax Description

all

Clears all ANCP neighbors.

description string

Identifies an ANCP neighbor. General string of up to 63 characters.

sender-name

ANCP neighbor identification.

H.H.H

MAC address of the sending interface.

A.B.C.D

IP address of the sending interface.

state

(Optional) Resets adjacencies.

statistics

(Optional) Resets only adjacency message statistics.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Neighbor data or statistics can be cleared individually or as a list.

If the state keyword is specified, adjacencies are not cleared, they are reset. ANCP adjacency protocol restarts, but TCP connections remain open. Unmapped ports belonging to the adjacency are removed.

If the statistics keyword is specified, the adjacency state remains intact and only adjacency message statistics are reset.

If neither option is specified, selected adjacencies are cleared, and if no description for these adjacencies is present, they are removed from the ANCP neighbor database. Whether the neighbor is reset or fully cleared, all unmapped ports belonging to this neighbor are removed. Mapped ports are placed in a down state and rates remain intact.


Note


Mapped access node port data is not affected by this operation.


Task ID

Task ID

Operations

ancp

read, write

Examples

The following example shows how to clear all neighbor data and statistics:

RP/0/RSP0/CPU0:router# clear ancp neighbor all

The following example shows how to clear a specific neighbor:

RP/0/RSP0/CPU0:router# clear ancp neighbor description vendor1a

Related Commands

Command

Description

clear ancp an-port

Clears access node (AN) ports of dynamic data or statistics.  

clear ancp summary statistics

Clears aggregate message statistics only, without modifying individual neighbor or port statistics.  

clear ancp summary statistics

To clear aggregate message statistics only, without modifying individual neighbor or port statistics, use the clear ancp summary statistics command in EXEC mode.

clear ancp summary statistics

Syntax Description

This command has no keywords or arguments.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

ancp

read, write

Examples

The following example shows how to clear aggregate message statistics:

RP/0/RSP0/CPU0:router# clear ancp summary statistics 

Related Commands

Command

Description

clear ancp an-port

Clears access node (AN) ports of dynamic data or statistics.  

clear ancp neighbor

Clears the adjacency connection with the neighbor.  

show ancp an-port

Use the show ancp an-port command to display data or message statistics referring to individual or multiple Access Node (AN) ports.

show ancp an-port [ { all | configured | dynamic-only | summary } [statistics] | statistics ]

Syntax Description

all

(Optional) Displays data for all AN ports.

configured

(Optional) Displays data for AN ports mapped to local subinterfaces.

dynamic-only

(Optional) Displays data for AN ports not mapped to any local subinterfaces.

summary

(Optional) Displays summary data for all active AN ports.

statistics

(Optional) Displays message statistics for AN ports.

Command Default

If no arguments are specified, the show ancp an-port command displays all ANCP ports sorted by circuit ID.

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 3.9.0

This command was updated to support the mapping of ANCP ports to VLAN interfaces over Ethernet bundles.

Release 4.0.0

This command was modified to provide information on the ICCP groups of VLAN sub-interfaces.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operation

ancp

read

Examples

The following example shows how to display the statistics for all AN ports.

RP/0/RSP0/CPU0:router# show ancp an-port all statistics                                

  List of AN port message statistics

  Circuit-id                     Port Up    Port Down  Total
  ------------------------------ ---------- ---------- ----------
  cir100_1                       1          0          1         
  cir101_1                       1          0          1         
  cir200_1                       0          0          0         
  

The following example shows how to display information and statistics for all AN ports mapped to any local VLAN subinterfaces..

RP/0/RSP0/CPU0:router# show ancp an-port configured 

  List of AN port data for ports mapped to local sub-interfaces

  ------------------------------ ----- ---------- -------- ---- ------------
                                                  Line     Num  Adjusted DS 
  Circuit-id                     State Uptime     State    Intf Rate (kbps) 
  ------------------------------ ----- ---------- -------- ---- ------------
  cir100_1                       UP    00:12:04   SHOWTIME 1    10000       
  cir101_1                       UP    00:12:04   SHOWTIME 1    10000       
  cir200_1                       -     00:00:00   -        1    0 

RP/0/RSP0/CPU0:router# show ancp an-port configured statistics 

  List of AN port message statistics for ports mapped to local sub-interfaces

  Circuit-id                     Port Up    Port Down  Total
  ------------------------------ ---------- ---------- ----------
  cir100_1                       1          0          1         
  cir101_1                       1          0          1         
  cir200_1                       0          0          0 
  

The following example shows how to display summary data for all AN ports.

RP/0/RSP0/CPU0:router# show ancp an-port summary    

     AN Port Summary
  --------------------------------
  State Up                 2
  State Down               0
  Config only ports        1
  Total                    3
  # Configured ports       3
  # Mapped sub-interfaces  3
  

Related Commands

Command

Description

show ancp an-port circuit-id

Displays data or message statistics for an AN port identified by its circuit-id.  

show ancp an-port interface

Displays data or message statistics for a sub-interface mapped to an AN port.  

show ancp an-port neighbor

Displays data or message statistics for AN ports associated with a specific neighbor.  

show ancp an-port state

Displays data or message statistics for AN ports which are in a specific state.  

show ancp an-port circuit-id

Use the show ancp an-port circuit-id command to display data or message statistics for an AN port identified by its circuit-id.

show ancp an-port circuit-id Access-Loop-Circuit-Id [ detail | statistics [detail] ]

Syntax Description

Access-Loop-Circuit-Id

Unique access loop circuit ID name identifying the access port. Maximum 63 characters.

detail

(Optional) Displays additional data on a list of interfaces mapped to the port.

statistics

(Optional) Displays message statistics for an AN port.

Command Default

No default behavior or values.

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 3.9.0

This command was updated to support the mapping of ANCP ports to VLAN interfaces over Ethernet bundles.

Release 4.0.0

This command was modified to provide information on the ICCP groups of VLAN sub-interfaces.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operation

ancp

read

Examples

The following example shows how to display information for an AN port identified by its circuit-id.

RP/0/RSP0/CPU0:router# show ancp an-port circuit-id cir100_1                           

  AN port circuit-id cir100_1:
  State                                                   UP
  Uptime                                                  00:11:31
  Time Since Last Message                                 00:11:31
  Encap Type                                              ETHERNET
  DSL type                                                VDSL2    
  DSL Line State                                          SHOWTIME
  Number of Mapped Sub-interfaces                         1
  Neighbor sender-name                                    0000.3200.0102
  Neighbor description                                    -
  Configured Rate Adjustment                              100%
  Actual Downstream Data Rate (kbps)                      10000
  Effective Downstream Data Rate (kbps)                   10000
  

The following example shows how to display statistics for an AN port identified by its circuit-id.

RP/0/RSP0/CPU0:router# show ancp an-port circuit-id cir100_1 statistics 

  Port message statistics for circuit-id cir100_1:

    Port Up       1
    Port Down     0
    -------------------------
    Total         1
  

Related Commands

Command

Description

show ancp an-port

Displays data or message statistics referring to individual or multiple Access Node (AN) ports.  

show ancp an-port interface

Displays data or message statistics for a sub-interface mapped to an AN port.  

show ancp an-port neighbor

Displays data or message statistics for AN ports associated with a specific neighbor.  

show ancp an-port state

Displays data or message statistics for AN ports which are in a specific state.  

show ancp an-port interface

Use the show ancp an-port interface command to display data or message statistics for a sub-interface mapped to an AN port.

show ancp an-port interface { physical interface-id [ detail | statistics [detail] ] | mapping }

Syntax Description

physical interface-id

(Optional) Physical layer identifier as defined in Table 1.

detail

(Optional) Displays additional data on a list of interfaces mapped to the port.

statistics

(Optional) Displays message statistics for an AN port.

mapping

(Optional) Displays a summary of sub-interface mapping to AN ports.

Command Default

No default behavior or values.

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 3.9.0

This command was updated to support the mapping of ANCP ports to VLAN interfaces over Ethernet bundles.

Release 4.0.0

This command was modified to provide information on the ICCP groups of VLAN sub-interfaces.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The following table defines physical interface id parameters available to refine the output of the show ancp redundancy iccp group command. Use any of the physical interface id parameters in place of the physical interface id argument.

Table 1 Physical Interface-id parameters for the show ancp an-port command

Syntax

Description

Bundle-Ether instance.subinterface

Specifies an aggregated Ethernet interface.

Replace the instance argument with an Ethernet bundle instance. Range is 1 to 65535.

Replace the subinterface argument with a subinterface value. Range is 0 to 21474883647.

GigabitEthernet instance.subinterface

Specifies a GigabitEthernet/IEEE 802.3 interface.

Replace the instance argument with a physical interface instance specified in the rack/slot/module/port notation.

Replace the subinterface argument with a subinterface value. Range is 0 to 21474883647.

TenGigE instance.subinterface

Specifies a TenGigabitEthernet/IEEE 802.3 interface.

Replace the instance argument with a physical interface instance specified in the rack/slot/module/port notation.

Replace the subinterface argument with a subinterface value. Range is 0 to 21474883647.

Task ID

Task ID

Operation

ancp

read

Examples

The following examples show how to display ANCP information and statistics for the Bundle-Ether interface at location 100.1:

RP/0/RSP0/CPU0:router# show ancp an-port interface bundle-Ether 100.1 

  AN port circuit-id cir100_1:

  State                                                   UP
  Uptime                                                  00:13:26
  Time Since Last Message                                 00:13:26
  Encap Type                                              ETHERNET
  DSL type                                                VDSL2    
  DSL Line State                                          SHOWTIME
  Number of Mapped Sub-interfaces                         1
  Neighbor sender-name                                    0000.3200.0102
  Neighbor description                                    -
  Configured Rate Adjustment                              100%
  Actual Downstream Data Rate (kbps)                      10000
  Effective Downstream Data Rate (kbps)                   10000


RP/0/RSP0/CPU0:router# show ancp an-port interface bundle-Ether 100.1 statistics 

  Port message statistics for circuit-id cir100_1:

    Port Up       1
    Port Down     0
    -------------------------
    Total         1

RP/0/RSP0/CPU0:router# show ancp an-port interface bundle-Ether 1.1 detail 
Tue Nov 17 17:28:44.390 EST

  AN port circuit-id ckt1:

  State                                                   -
  Uptime                                                  00:00:00
  Time Since Last Message                                 00:00:00
  Encap Type                                              -
  DSL type                                                -
  DSL Line State                                          -
  Number of Mapped Sub-interfaces                         3
  Neighbor sender-name                                    -
  Neighbor description                                    -
  Configured Rate Adjustment                              0%
  Actual Downstream Data Rate (kbps)                      0
  Effective Downstream Data Rate (kbps)                   0
  Actual Data Rate Upstream/Downstream (kbps)             0/0
  Minimum Data Rate Upstream/Downstream (kbps)            0/0
  Attainable Data Rate Upstream/Downstream (kbps)         0/0
  Maximum Data Rate Upstream/Downstream (kbps)            0/0
  Minimum Low Power Data Rate Upstream/Downstream (kbps)  0/0
  Maximum Interleaving Delay Upstream/Downstream (ms)     0/0
  Actual Interleaving Delay Upstream/Downstream (ms)      0/0

  Sub-interface Summary: total 3
  -----------------------------------------------
  Sub-interface name                ifhandle    ICCP Group    Redundancy State
  --------------------------------  ----------  ------------ 
------------------------
  Bundle-Ether1.1                   0x20000072  1             ACTIVE 
   
  GigabitEthernet0/0/0/0.1          0x20000022  0             DOWN 
   
  GigabitEthernet0/0/0/0.2          0x20000042  0             DOWN  
  

Related Commands

Command

Description

show ancp an-port

Displays data or message statistics referring to individual or multiple Access Node (AN) ports.  

show ancp an-port circuit-id

Displays data or message statistics for an AN port identified by its circuit-id.  

show ancp an-port neighbor

Displays data or message statistics for AN ports associated with a specific neighbor.  

show ancp an-port state

Displays data or message statistics for AN ports which are in a specific state.  

show ancp an-port neighbor

Use the show ancp an-port neighbor command to display data or message statistics for AN ports associated with a specific neighbor.

show ancp an-port neighbor { description description | none | sender-name { H.H.H | A.B.C.D } } [ statistics ]

Syntax Description

description description

(Optional) Identifies the neighbor by description. The argument description has a maximum of 63 characters.

none

(Optional) Displays AN ports not associated with a neighbor.

sender-name

(Optional) Identifies the neighbor by sender-name.

H.H.H

(Optional) MAC address of the sending interface.

A.B.C.D

(Optional) IPv4 address of the sending interface.

statistics

(Optional) Displays port message statistics for a specific AN port.

Command Default

No default behaviour or values.

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 3.9.0

This command was updated to support the mapping of ANCP ports to VLAN interfaces over Ethernet bundles.

Release 4.0.0

This command was modified to provide information on the ICCP groups of VLAN sub-interfaces.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operation

ancp

read

Examples

The following example shows how to display information and statistics for AN ports not associated with any neigbor:

RP/0/RSP0/CPU0:router# show ancp an-port neighbor none 

  List of AN port data for ports associated with no neighbor

  ------------------------------ ----- ---------- -------- ---- ------------
                                                  Line     Num  Adjusted DS 
  Circuit-id                     State Uptime     State    Intf Rate (kbps) 
  ------------------------------ ----- ---------- -------- ---- ------------
  cir200_1                       -     00:00:00   -        1    0           


RP/0/RSP0/CPU0:router# show ancp an-port neighbor none statistics 

  List of AN port message statistics for ports associated with no neighbor

  Circuit-id                     Port Up    Port Down  Total
  ------------------------------ ---------- ---------- ----------
  cir200_1                       0          0          0 
  

The following example shows how to display information and statistics on all AN ports associated with a neighbor identified by its sender-name:

RP/0/RSP0/CPU0:router# show ancp an-port neighbor sender-name 0000.3200.0102

  List of AN port data for neighbor sender name 0000.3200.0102

  ------------------------------ ----- ---------- -------- ---- ------------
                                                  Line     Num  Adjusted DS 
  Circuit-id                     State Uptime     State    Intf Rate (kbps) 
  ------------------------------ ----- ---------- -------- ---- ------------
  cir100_1                       UP    00:18:03   SHOWTIME 1    10000       

RP/0/RSP0/CPU0:router# show ancp an-port neighbor sender-name 0000.3200.0102 statistics 

  List of AN port message statistics for neighbor sender name 0000.3200.0102

  Circuit-id                     Port Up    Port Down  Total
  ------------------------------ ---------- ---------- ----------
  cir100_1                       1          0          1 
  

Related Commands

Command

Description

show ancp an-port

Displays data or message statistics referring to individual or multiple Access Node (AN) ports.  

show ancp an-port circuit-id

Displays data or message statistics for an AN port identified by its circuit-id.  

show ancp an-port interface

Displays data or message statistics for a sub-interface mapped to an AN port.  

show ancp an-port state

Displays data or message statistics for AN ports which are in a specific state.  

show ancp an-port state

Use the show ancp an-port state command to display data or message statistics for AN ports which are in a specific state.

show ancp an-port state { up | down | none } [statistics]

Syntax Description

up

(Optional) Displays information about AN ports in an up state.

down

(Optional) Displays information about AN ports in a down state.

none

(Optional) Displays information about AN ports not reported by any neighbor.

statistics

(Optional) Displays port message statistics for a specific AN port.

Command Default

No default behaviour or values.

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Release 3.9.0

This command was updated to support the mapping of ANCP ports to VLAN interfaces over Ethernet bundles.

Release 4.0.0

This command was modified to provide information on the ICCP groups of VLAN sub-interfaces.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operation

ancp

read

Examples

The following example shows how to display information for all AN ports in an Up state:

RP/0/RSP0/CPU0:router# show ancp an-port state up

  List of AN port data for ports in UP state

  ------------------------------ ----- ---------- -------- ---- ------------
                                                  Line     Num  Adjusted DS 
  Circuit-id                     State Uptime     State    Intf Rate (kbps) 
  ------------------------------ ----- ---------- -------- ---- ------------
  cir100_1                       UP    00:18:42   SHOWTIME 1    10000       
  cir101_1                       UP    00:18:42   SHOWTIME 1    10000       

The following example shows how to display information for all AN ports not reported by any neighbor:

RP/0/RSP0/CPU0:router# show ancp an-port state none 

  List of AN port data for ports with NO state

  ------------------------------ ----- ---------- -------- ---- ------------
                                                  Line     Num  Adjusted DS 
  Circuit-id                     State Uptime     State    Intf Rate (kbps) 
  ------------------------------ ----- ---------- -------- ---- ------------
  cir200_1                       -     00:00:00   -        1    0 

Related Commands

Command

Description

show ancp an-port

Displays data or message statistics referring to individual or multiple Access Node (AN) ports.  

show ancp an-port circuit-id

Displays data or message statistics for an AN port identified by its circuit-id.  

show ancp an-port interface

Displays data or message statistics for a sub-interface mapped to an AN port.  

show ancp an-port neighbor

Displays data or message statistics for AN ports associated with a specific neighbor.  

show ancp neighbor

To display data or message statistics associated with individual ANCP adjacencies or sets of adjacencies, use the show ancp neighbor command in EXEC mode.

show ancp neighbor { description string | sender-name { H.H.H | A.B.C.D } } [all] state { none | synsent | synrcvd | estab } [statistics] [summary]

Syntax Description

description string

Identifier of ANCP neighbor. General string up to 63 characters.

sender-name

ANCP neighbor identification.

H.H.H

MAC address of the sending interface.

A.B.C.D

IP address of the sending interface.

all

Displays all ANCP neighbors.

state

Displays ANCP neighbors in specified state.

  • none—Displays ANCP neighbors in a down state.
  • synsent—Displays ANCP neighbors in the SYNSENT state.
  • synrcvd—Displays ANCP neighbors in the SYNRCVD state.
  • estab—Displays ANCP neighbors in the ESTAB state.

statistics

(Optional) Displays packet statistics.

summary

(Optional) Displays a summary of all active ANCP neighbors.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

ancp

read, write

Examples

The following example shows the output from a specific neighbor using the sender-name MAC address:

RP/0/RSP0/CPU0:router# show ancp neighbor sender-name 0006.2aaa.281b

             ANCP Neighbor Data
  -------------------------------------------
  Sender Name              0006.2aaa.281b
  Description              first
  State                    ESTAB
  Capability               Topology Discovery
  Ports:
    State Up               25
    State Down             5
    Total                  30

The following example shows the same command with the addition of the detail keyword, showing a summary of AN ports that were reported by that neighbor:

RP/0/RSP0/CPU0:router# show ancp neighbor sender-name 0006.2aaa.281b detail

              ANCP Neighbor Data
  -------------------------------------------
  Sender Name               0006.2aaa.281b
  Description               first
  State                     ESTAB
  Capability                Topology Discovery
  Ports:
    State Up                4
    State Down              0
    Total                   4
Remote IP Addr/TCP Port   4.11.0.1/11126
Local  IP Addr/TCP Port   4.11.0.100/6068
Server Sender Name        0013.1aff.c2bd
Remote Timeout            25500 msec
Local  Timeout            10000 msec
Adjacency Uptime          01:25:20
Time Since Last Port Msg  00:00:04
Remote Port               0
Remote Instance           1
Local Instance            1
Remote Partition ID       0

List of AN port data for neighbor sender name 0006.2aaa.281b
------------------------------ ----- ---------- -------- ----  ------------
                                               Line      Num   Adjusted DS
Circuit-id                     State Uptime    State     Intf  Rate (kbps)
------------------------------ ----- ---------- -------- ----  ------------
circuit1                       UP    00:27:49  SHOWTIME   3    2250
circuti2                       UP    00:00:49  SHOWTIME   2    2250
circuit3                       UP    00:00:49  SHOWTIME   2    2250
circuti4                       UP    00:00:49  SHOWTIME   0    2250

The following example shows the same command, this time with the addition of the statistics keyword, showing a summary of message statistics for the selected neighbor:

RP/0/RSP0/CPU0:router# show ancp neighbor sender-name 0006.2aaa.281b statistics

ANCP Neighbor Message Statistics
for Sender-name -, Description 0006.2aaa.281b
-----------------------------------------------
               Sent         Received
SYN            1            2
SNYACK         1            0
ACK            589          238
RSTACK         0            0
Port Up        -            10
Port Down      -            0
Drops          0            0
Total          600          250

Related Commands

Command

Description

clear ancp neighbor

Clears the adjacency connection with the neighbor.  

show ancp an-port

Displays data or message statistics referring to individual or multiple Access Node (AN) ports.  

show ancp neighbor summary

Displays adjacency counts by state.  

show qos summary

Lists the interfaces at a specific location.  

show ancp neighbor summary

To display adjacency counts by state, use the show ancp neighbor summary command in EXEC mode.

show ancp neighbor summary [statistics] [detail]

Syntax Description

statistics

(Optional) Provides summary message statistics.

detail

(Optional) Displays the current rate adjustment table.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

ancp

read, write

Examples

The following example shows the output from the show ancp neighbor summary command:

RP/0/RSP0/CPU0:router# show ancp neighbor summary

    ANCP Neighbor Summary Information
    ---------------------------------
    Neighbor count by state:
     -                0
     SYNSENT          0
     SYNRCVD          0
     ESTAB            1
  

The following example shows the same command with the addition of the detail keyword, showing a summary of individual neighbor data:

RP/0/RSP0/CPU0:router# show ancp neighbor summary detail

    ANCP Neighbor Summary Information
    ---------------------------------
    Neighbor count by state:
     -                0
     SYNSENT          0
     SYNRCVD          0
     ESTAB            1

  Summary Data By Neighbor
----------------------------------------------------------
Neighbor          Neighbor                 Port Cnt by State
Description       Sender-Name     State    Up       Down   
----------------- --------------  -------- -------  -------
first             0006.2aaa.281b  ESTAB    5        2
-                 0101.0101.0000  -        0        0
  

This example shows how to display summary message statistics by adding the statistics keyword to the show ancp neighbor summary command:

RP/0/RSP0/CPU0:router# show ancp neighbor summary statistics

    ANCP summary Neighbor Statistics
  ------------------------------------
                 Sent          Received
   SYN           4             8
   SYNACK        5             0
   ACK           8886          3525
   RSTACK        2             0
   Port Up       -             16
   Port Down     -             0
   Drops         0             0
Total            8897          3549
  

Related Commands

Command

Description

show ancp an-port

Displays data or message statistics referring to individual or multiple Access Node (AN) ports.  

show ancp neighbor

Displays data or message statistics associated with individual ANCP adjacencies or sets of adjacencies.  

show ancp summary

Displays information about ANCP configuration, including server sender name and neighbor and port counts by state.  

show ancp redundancy iccp

To display the state or statistics of ICCP in the ANCP application, use the show ancp redundancy iccp command in EXEC mode.

show ancp redundancy iccp [statistics]

Syntax Description

statistics

(Optional) Displays the ANCP ICCP statistics.

Command Default

No default behaviour or values.

Command Modes

EXEC

Command History

Release

Modification

Release 4.0.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operation

ancp

read

Examples

The following example shows how to display the state of ICCP in the ANCP application:

RP/0/RSP0/CPU0:router# show ancp redundancy iccp
Tue Nov 17 17:17:04.043 EST

ANCP ICCP Information
---------------------------------------------------------------
ICCP State                   UP
ICCP Congestion              Cleared
ICCP Group Count             1
ICCP Group Interface Count   1
Creation Timestamp           Tue Nov 17 14:20:15 2009
  

The following table describes the significant fields shown in the display.

Table 2 show ancp redundancy iccp Field Descriptions

Field

Description

ICCP State

ANCP ICCP State.

ICCP Congestion

State of ICCP congestion.

ICCP Group Count

Number of ICCP Groups that ANCP VLAN sub-interfaces are members of.

ICCP Group Interface Count

Number of MC-LAG VLAN sub-interfaces to which ANCP circuits are mapped.

Creation Timestamp

Timestamp of ANCP registration with the ICCP server.

The following example shows how to display the ANCP ICCP statistics:

RP/0/RSP0/CPU0:router# show ancp redundancy iccp statistics
Tue Nov 17 17:17:08.150 EST

ANCP ICCP Statistics
---------------------------------------------------------------

ICCP Statistics
---------------------------------------------------------------
Up Rx                          1
Down Rx                        0
Congestion Clear Rx            0
Congestion Clear Rx Drop       0
Congestion Detecetd Rx         0
Congestion Detecetd Rx Drop    0
Tx Failure                     0

ICCP Group Statistics
---------------------------------------------------------------
Peer Up Rx                     0
Peer Down Rx                   0
Sync Request Rx                0
Connect Tx                     1
Connect Tx Failure             0
Disconnect Tx                  0
Disconnect Tx Failure          0
Start Retry Timer              0

ICCP Interface Statistics
---------------------------------------------------------------
Active Rx                      0
Standby Rx                     0
Down Rx                        0
Sync Request Rx                0
Sync Request Rx Drop           0
Sync Request Tx                0
Sync Request Tx Drop           0
Sync Rx                        0
Sync Rx Drop                   0
Sync Start Rx                  0
Sync Start Rx Drop             0
Sync End Rx                    0
Sync End Rx Drop               0
Sync Unsolicited Rx            0
Sync Unsolicited Rx Drop       0
Sync Invalid Rx                0
Sync Tx                        0
Sync Tx Drop                   0
App State Rx                   0
App_State_Rx Drop              0
App State Tx                   0
App_State_Tx Drop              0
Start Retry Timer              0
  

The output indicates the number and type of messages (for example, Up Rx) received (denoted by Rx) and transmitted (denoted by Tx) by the ANCP application. Failure denotes a failed message. Drop indicates a dropped message. Start Retry Timer indicates the number of times the Retry Timer has been initiated as a result of a message transmission failure.

Related Commands

Command

Description

show ancp redundancy iccp group

Displays the state and statistics of an ICCP Group in the ANCP application.

show iccp group

Displays summary of the configured ICCP Groups and their states.

show ancp redundancy iccp group

To display the state and/or statistics of an ICCP Group that an ANCP VLAN sub-interface is a member of, use the show ancp redundancy iccp group command in EXEC mode.

show ancp redundancy iccp group [ ICCP group id [ interface Bundle-Ether instance .subinterface [statistics] | statistics ] | detail | interface [ Bundle-Ether instance .subinterface [statistics] | detail | statistics ] | statistics ]

Syntax Description

ICCP group id

(Optional) Number identifying the ICCP Group. Range is 1 to 24.

interface

(Optional) Displays information for a particular physical layer interface.

Bundle-Ether instance.subinterface

(Optional) Specifies an aggregated Ethernet interface.

Replace the instance argument with an Ethernet bundle instance. Range is 1 to 65535.

Replace the subinterface argument with a subinterface value. Range is 0 to 21474883647.

statistics

(Optional) Displays message statistics.

detail

(Optional) Displays detailed information.

Command Default

No default behavior or values.

Command Modes

EXEC

Command History

Release

Modification

Release 4.0.0

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operation

ancp

read

Examples

The following example shows how to display the state of ICCP groups configured on the ANCP application:

RP/0/RSP0/CPU0:router# show ancp redundancy iccp group  
Tue Nov 17 17:19:30.484 EST

ICCP                                Active      Standby

Group Id                 Peers      Interfaces  Interfaces  ICCP Group State
-------------------------------------------------------------------------------------------
1                        1          1           0           Connected Peer Present

The output indicates the Group IDs, their states, and the number of peers. It also indicates the number of interfaces within each group for which the ANCP is the active or standby PoA.

The following example shows how to display details of ICCP Group 1: 

RP/0/RSP0/CPU0:router# show ancp redundancy iccp group 1
Tue Nov 17 17:19:33.470 EST

ICCP Group 1 Information
---------------------------------------------------------------
State                         Connected Peer Present
Previous State                Connected No Peers
Number of Active Interfaces   1
Number of Standby Interfaces  0
Number of Peers               1
Creation Timestamp            Tue Nov 17 17:16:57 2009


ICCP Group 1 Peers 

Ip Address       Timestamp
-----------------------------
10.10.10.1       Tue Nov 17 17:18:49 2009

The output indicates the current and previous states of ICCP Group 1, its creation timestamp, and the number of peers and their IP addresses. It also indicates the number of interfaces within each group for which the ANCP is the active or standby PoA.

The following example shows how to display the statistics of ICCP Group 1: 

RP/0/RSP0/CPU0:router# show ancp redundancy iccp group 1 statistics
Tue Nov 17 17:19:38.262 EST

ICCP Group 1 Statistics
---------------------------------------------------------------
Peer Up Rx                     1
Peer Down Rx                   0
Sync Request Rx                0
Connect Tx                     1
Connect Tx Failure             0
Disconnect Tx                  0
Disconnect Tx Failure          0
Start Retry Timer              0

ICCP Group 1 Interface Statistics
---------------------------------------------------------------
Active Rx                      1
Standby Rx                     0
Down Rx                        0
Sync Request Rx                0
Sync Request Rx Drop           0
Sync Request Tx                4
Sync Request Tx Drop           0
Sync Rx                        0
Sync Rx Drop                   0
Sync Start Rx                  0
Sync Start Rx Drop             0
Sync End Rx                    0
Sync End Rx Drop               0
Sync Unsolicited Rx            0
Sync Unsolicited Rx Drop       0
Sync Invalid Rx                0
Sync Tx                        0
Sync Tx Drop                   0
App State Rx                   0
App_State_Rx Drop              0
App State Tx                   0
App_State_Tx Drop              0
Start Retry Timer              4
  

The output indicates the number and type of messages (for example, Up Rx) received (denoted by Rx) and transmitted (denoted by Tx) in ICCP Group 1. Failure denotes a failed message. Drop indicates a dropped message. Start Retry Timer indicates the number of times the Retry Timer has been initiated as a result of a message transmission failure.

The following example shows how to display information on the ICCP interfaces.

RP/0/RSP0/CPU0:router# show ancp redundancy iccp group interface
Tue Nov 17 17:24:31.356 EST

ICCP Interfaces 

Interface                         ICCP Group Id  Redundancy State    ICCP Group Port State
---------------------------------------------------------------------------------------------------
Bundle-Ether1.1                   1              ACTIVE              Active Peers              
  

The output indicates the MC-LAG Bundle-Ether sub-interfaces that are mapped to ANCP circuits, their ICCP Group ID’s, redundancy states and ICCP Group Port States.

The following example shows how to display information on the Bundle-Ether interface at location 1.1.

RP/0/RSP0/CPU0:router# show ancp redundancy iccp group interface bundle-Ether 1.1
Tue Nov 17 17:24:37.111 EST

ICCP Group Interface Bundle-Ether1.1
---------------------------------------------------------------
ICCP Group Id                           1
Redundancy State                        ACTIVE
ICCP Group Port                         Active ICCP Down
Previous State                          Active No Peers
Last Redundancy State Change Timestamp  Thu Aug  5 12:20:40 2010
Last Sync Timestamp                     None
Creation Timestamp                      Thu Aug  5 12:20:40 2010
Request Id                              0
Retry Timer                             Not Running
Retry Timer Period                      0
  

The output displays information about the MC-LAG Bundle-Ether 1.1 interface, which is mapped to an ANCP circuit. ICCP Group Port indicates the current state of the ICCP Group Port. Previous State indicates the previous state of the ICCP Group Port. The Request ID is the tag attached to the last request message sent to the active PoA, for this interface. It is used to correlate PoA requests and responses. When a response to a request is not received, the request message is resent after the Retry Timer Period has elapsed. The Retry Timer field indicates the current state of the retry timer.

The following example shows how to display statistics for the Bundle_Ether interface at location 1.1.

RP/0/RSP0/CPU0:router# show ancp redundancy iccp group interface bundle-Ether 1.1 statistics
Tue Nov 17 17:24:42.662 EST

ICCP Group Interface Bundle-Ether1.1 Statistics
---------------------------------------------------------------
Active Rx                      1
Standby Rx                     0
Down Rx                        0
Sync Request Rx                0
Sync Request Rx Drop           0
Sync Request Tx                4
Sync Request Tx Drop           0
Sync Rx                        0
Sync Rx Drop                   0
Sync Start Rx                  0
Sync Start Rx Drop             0
Sync End Rx                    0
Sync End Rx Drop               0
Sync Unsolicited Rx            0
Sync Unsolicited Rx Drop       0
Sync Invalid Rx                0
Sync Tx                        0
Sync Tx Drop                   0
App State Rx                   0
App_State_Rx Drop              0
App State Tx                   0
App_State_Tx Drop              0
Start Retry Timer              4
  

The output indicates the number and type of messages (for example, Up Rx) received (denoted by Rx) and transmitted (denoted by Tx), which relate to the MC-LAG Bundle Ether 1.1. interface. Failure denotes a failed message. Drop indicates a dropped message. Start Retry Timer indicates the number of times the Retry Timer has been initiated as a result of a message transmission failure.

The following example shows how to display information on the ICCP Group 1 interfaces

RP/0/RSP0/CPU0:router# show ancp redundancy iccp group 1 interface
Tue Nov 17 17:25:18.302 EST

ICCP Interfaces 

Interface                         ICCP Group Id  Redundancy State    ICCP Group Port State
---------------------------------------------------------------------------------------------------
Bundle-Ether1.1                   1              ACTIVE              Active Peers              
  

The output indicates the redundancy states and ICCP Group Port States of the MC-LAG Bundle-Ether sub-interfaces that are mapped to ANCP circuits in ICCP Group 1.

The following example shows how to display information on the Bundle_Ether interface, in ICCP Group 1, at location 1.1.

RP/0/RSP0/CPU0:router# show ancp redundancy iccp group 1 interface bundle-Ether 1.1
Tue Nov 17 17:25:24.389 EST

ICCP Group Interface Bundle-Ether1.1
---------------------------------------------------------------
ICCP Group Id                           1
Redundancy State                        ACTIVE
ICCP Group Port                         Active ICCP Down
Previous State                          Active No Peers
Last Redundancy State Change Timestamp  Thu Aug  5 12:20:40 2010
Last Sync Timestamp                     None
Creation Timestamp                      Thu Aug  5 12:20:40 2010
Request Id                              0
Retry Timer                             Not Running
Retry Timer Period                      0
  

The output displays information about the MC-LAG Bundle-Ether 1.1 interface, in ICCP Group 1, which is mapped to an ANCP circuit. ICCP Group Port indicates the current state of the ICCP Group Port. Previous State indicates the previous state of the ICCP Group Port. The Request ID is the tag attached to the last request message sent to the active PoA, for this interface. It is used to correlate PoA requests and responses. When a response to a request is not received, the request message is resent after the Retry Timer Period has elapsed. The Retry Timer field indicates the current state of the retry timer.

The following example shows how to display statistics for the Bundle_Ether interface, in ICCP Group 1, at location 1.1.

RP/0/RSP0/CPU0:router# show ancp redundancy iccp group 1 interface bundle-Ether 1.1 statistics
Tue Nov 17 17:25:27.719 EST

ICCP Group Interface Bundle-Ether1.1 Statistics
---------------------------------------------------------------
Active Rx                      1
Standby Rx                     0
Down Rx                        0
Sync Request Rx                0
Sync Request Rx Drop           0
Sync Request Tx                4
Sync Request Tx Drop           0
Sync Rx                        0
Sync Rx Drop                   0
Sync Start Rx                  0
Sync Start Rx Drop             0
Sync End Rx                    0
Sync End Rx Drop               0
Sync Unsolicited Rx            0
Sync Unsolicited Rx Drop       0
Sync Invalid Rx                0
Sync Tx                        0
Sync Tx Drop                   0
App State Rx                   0
App_State_Rx Drop              0
App State Tx                   0
App_State_Tx Drop              0
Start Retry Timer              4
  

The output indicates the number and type of messages (for example, Up Rx) received (denoted by Rx) and transmitted (denoted by Tx) which relate to the MC-LAG Bundle Ether 1.1. interface, in ICCP Group 1. Failure denotes a failed message. Drop indicates a dropped message. Start Retry Timer indicates the number of times the Retry Timer has been initiated as a result of a message transmission failure.

Related Commands

Command

Description

show ancp redundancy iccp

Displays the state or statistics of ICCP in the ANCP application.  

show ancp summary

To display information about ANCP configuration, including server sender name and neighbor and port counts by state, use the show ancp summary command in EXEC mode.

show ancp summary [statistics] [detail]

Syntax Description

statistics

(Optional) Provides a summary of ANCP message statistics.

detail

(Optional) Provides rate adjustment configuration information in addition to the show ancp summary output.

Command Default

No default behavior or values

Command Modes

EXEC

Command History

Release

Modification

Release 3.7.2

This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID

Task ID

Operations

ancp

read

Examples

The following example shows how to display generic information about ANCP configuration, along with neighbor and port counts by state:

RP/0/RSP0/CPU0:router# show ancp summary
    ANCP Summary Information
   ----------------------------------------------
   Capability:                 Topology Discovery
   Server sender-name:         0013:1aff.c2bd

Neighbor count by state:
  -                            0
  SYNSENT                      0
  SUNRCVD                      0
  ESTAB                        1
  ----------------------------------
  Total                        1

Port count by state:
  State Up                     1
  State Down                   0
  State Unknown                0
  ----------------------------------
  Total                        1

  No. configured ports         1
  No. mapped sub-interfaces    4
  

The following example shows how to display rate adjustment configuration information in addition to the generic information shown in the previous example:

RP/0/RSP0/CPU0:router# show ancp summary detail
    ANCP Summary Information
   ----------------------------------------------
   Capability:                 Topology Discovery
   Server sender-name:         0013:1aff.c2bd

Neighbor count by state:
  -                            0
  SYNSENT                      0
  SUNRCVD                      0
  ESTAB                        1
  ----------------------------------
  Total                        1
Port count by state:
  State Up                     1
  State Down                   0
  State Unknown                0
  ----------------------------------
  Total                        1

  No. configured ports         1
  No. mapped sub-interfaces    4

Rate adjustment configuration:
-------------------------------------------
DSL Type   Loop Type        Percent-Factor
-------------------------------------------
ADSL1      ETHERNET                90
ADSL2      ETHERNET                100
ADSL2PLUS  ETHERNET                100
VDSL1      ETHERNET                100
VDSL2      ETHERNET                100
SDSL       ETHERNET                100
ADSL1      ATM                     100
ADSL2      ATM                     100
ADSL2PLUS  ATM                     100
VDSL1      ATM                     100
VDSL2      ATM                     100
SDSL       ATM                     100
  

The following example shows how to display a summary of ANCP message statistics:

RP/0/RSP0/CPU0:router# show ancp summary statistics

    ANCP Summary Message Statistics
   --------------------------------------
                 Sent          Received
   SYN           3             6
   SYNACK        4             0
   ACK           7105          2819
   RSTACK        2             0
   Port Up       -             6
   Port Down     -             0
   Drops         0             0
   Total         7114          2831
  

Related Commands

Command

Description

show ancp an-port

Displays data or message statistics referring to individual or multiple Access Node (AN) ports.  

show ancp neighbor

Displays data or message statistics associated with individual ANCP adjacencies or sets of adjacencies.  

show ancp neighbor summary

Displays adjacency counts by state.