Guest

Cisco ASR 9000 Series Aggregation Services Routers

New and Changed Commands in Cisco IOS XR Software, Release 5.1.x, for Cisco ASR 9000 Series Aggregation Services Routers

  • Viewing Options

  • PDF (1.2 MB)
  • Feedback
New and Changed Commands

New and Changed Commands

This list summarizes the commands which were newly added and changed in Cisco IOS XR Software, Release 5.1.x , and gives you the location where the commands are documented.

To read additional information about Cisco IOS XR Software features, see the Release Notes:

Release Notes

The latest versions of Cisco IOS XR Software documents are available at:

Cisco IOS XR Software Documents

Configuration Guides

Command References

Commands Newly Added and Changed in Release 5.1.x

Command History

Table 1 Commands newly added and changed for Cisco ASR 9000 Series Routers
Command Change Description

Release 5.1.2

 
hw-module bfd-hw-offload

This command was introduced.

show bfd hw-offload

This command was introduced.

address-family l2vpn mspw

This command was introduced.

bgp

This command was introduced.

global-id

This command was introduced.

neighbor routed

This command was introduced.

pw-routing

This command was introduced.

rd

This command was introduced.

show bgp l2vpn mspw

This command was introduced.

show l2vpn xconnect

This command was modified to enable filtering the command output for specific pseudowire with just the pseudowire ID.

clear mmrp-flood-optimization statistics

This command was introduced.

clear l2vpn forwarding counters bridge-domain mmrp location

This command was introduced.

debug mmrp-flood-optimization packets

This command was introduced.

debug mmrp-flood-optimization protocol

This command was introduced.

flood-time

This command was introduced.

join-time

This command was introduced.

leaveall-time

This command was introduced.

leave-time

This command was introduced.

mmrp-flood-optimization

This command was introduced.

periodic transmit

This command was introduced.

show mmrp-flood-optimization

This command was introduced.

path-selection cost-limit

This command was introduced.

show mpls traffic-eng preemption log

The command output was modified to display the log of soft-preemption over FRR backup tunnels events.

show mpls traffic-eng tunnels

These changes were made to support the path-selection cost-limit feature: The command output was modified to show the configured cost-limit. The shown PCALC error was modified to show cost-limit failure: applies for new paths and verification of existing paths. The 'Reopt Reason' field in the show output was modified to show the cost-limit. The path-protection switchover reason in the show output was modified to show the cost-limit. The command output was modified to display the 'Traffic switched to FRR backup tunnel-te' message as part of Soft-preemption over FRR backup tunnels feature implementation.

soft-preemption frr-rewrite

This command was introduced.

show ipv6 interface

The link-local and global keywords were added to the command.

clear applications

This command was introduced.

clear onep statistics

This command was introduced.

clear history buffer

This command was introduced.

clear history syslog

This command was introduced.

clear session max

This command was introduced.

datapath

This command was introduced.

dataplane-default

This command was introduced.

history buffer

This command was introduced.

history buffer disable

This commands was introduced.

onep

This command was introduced.

onep stop session

This command was introduced.

openflow switch

This command was introduced.

session max

This command was introduced.

show onep history

This command was introduced.

show onep session

This command was introduced.

show onep statistics

This command was introduced.

show onep status

This command was introduced.

shutdown

This command was introduced.

transport

This command was introduced.

Release 5.1.1

 
ipsubscriber interface

This command was introduced.

ipsubscriber routed

This command was introduced.

subscriber session limit

This command was introduced.

clear cgn nat44 inside-vrf counters

This command was introduced.

filter-policy

This command was introduced.

firewall

This command was introduced.

sequence-check

This command was introduced.

show cgn nat44 inside-vrf counters

This command was introduced.

show virtual-service

This command was introduced.

virtual-service

This command was introduced.

tunnel key ignore

This command was introduced.

tunnel key

This command was introduced.

match cac

This command was introduced.

match flow-key

This command was introduced.

show qos-ea interface

The show outputs were updated for CAC and UBRL details. PWHE Ethernet interface type PW-Ether and PW-IW were added.

show qos interface

The show qos interface command output was updated to display Flow Aware call admission control (CAC) and user based rate limiting (UBRL) information. The show qos interface command output was updated to display QoS Offload on satellite information.

show qos status interface

This command was introduced.

admit cac local

This command was introduced.

flow idle-timeout

This command was introduced.

flow rate

This command was introduced.

rate

This command was introduced.

hw-module flow-qos location max-flow-count

This command was introduced.

police bucket

This command was introduced.

show qos interface

The show qos interface command output was updated to display Flow Aware call admission control (CAC) and user based rate limiting (UBRL) information. The show qos interface command output was updated to display QoS Offload on satellite information.

show qos-ea interface

The show outputs were updated for CAC and UBRL details. PWHE Ethernet interface type PW-Ether and PW-IW were added.

show policy-map interface

The nv satellite keywords and the satellite-id variable were added. The show outputs were updated for nv satellite details. The show outputs were updated for CAC and UBRL details.

show policy-map targets

The show outputs were updated for nv satellite details.

show qos flow-aware summary location

This command was introduced.

hw-module all qos-mode ingress-queue-enable

This command was introduced.

hw-module all qos-mode per-priority-buffer-limit

This command was introduced.

hw-module all qos-mode wred-buffer-mode

This command was introduced.

show qoshal qos-mode

This command was introduced.

clear qos counters interface

The nv satellite keywords and the satellite-id variable were added.

affinity-map

The bit-position value range was changed to 1 to 255 that enables to assign up to 256 names for extended admin groups (EAGs).

attribute-names

Support was added to assign up to 32 names per attribute-set and index for extended admin groups. The index index-value keyword and argument were added to support extended admin groups (EAG) configuration.

autoroute announce

The include-ipv6 keyword was added to support MPLS-TE tunnel announcements to IS-IS.

autoroute destination

This command was introduced.

auto-tunnel pcc

This command was introduced.

capabilities (MPLS-TE)

This command was introduced.

forwarding-adjacency

The include-ipv6 keyword was added to support IPv6 forwarding adjacency announcements.

ipv6 enable

This command was introduced.

pce stateful-client

This command was introduced.

show interfaces tunnel-te accounting

This command was introduced.

show isis mpls traffic-eng tunnel

This command was introduced.

show mpls traffic-eng autoroute

Support was added to include name tunnel-name keyword and argument and to display signalled-name in the command output. Support was added to display MPLS TE IPv6 autoroute announce information for IS-IS IGP.

show mpls traffic-eng counters signaling

Support was added to include signame keyword and to display signalled-name in the command output.

show mpls traffic-eng forwarding-adjacency

Support was added to display information on IPv6 autoroute forwarding adjacency information for IS-IS IGP.

show mpls traffic-eng pce peer

The stateful keyword was added. Command output was updated to display stateful PCE information.

show mpls traffic-eng topology

Support was added to include signame keyword and to display signalled-name in the command output.

show mpls traffic-eng tunnels

The command output was modified to display information on stateful PCE client (PCC) auto-tunnels. Support was added to include signame keyword and to display signalled-name in the command output.

tunnel-id (auto-tunnel pcc)

This command was introduced.

show mfib bvi

This command was introduced.

show mrib bvi

This command was introduced.

mdt data ingress replication

This command was introduced.

address-family (BGP)

The link-state link-state keyword was added.

advertise permanent-network

This command was introduced.

distribute bgp-ls (ISIS)

This command was introduced.

distribute bgp-ls (OSPF)

This command was introduced.

domain-distinguisher

This command was introduced.

permanent-network

This command was introduced.

show bgp

The command output was modified to display the status of permanent paths.

show bgp neighbors

The command output was modified to display the status of permanent paths.

show bgp update-group

The command output was modified to include the status of advertised permanent paths.

prefix-set

The command was modified to accept IPv4 and IPv6 address and address mask to define a prefix set.

exclude-group

This command was introduced.

show apply-group

This command was introduced.

show configuration failed

This command was introduced.

responder twamp

This command was introduced.

server twamp

This command was introduced.

show ipsla twamp connection

This command was introduced.

show ipsla twamp session

This command was introduced.

show ipsla twamp standards

This command was introduced.

Release 5.1.0

 
network (BNG)

Support for IPv4 default-router was added.

event

The idle-timeout event was added.

broadcast-flag policy check (BNG)

The unicast-always keyword was added.

interface (DHCP-BNG)

The support for server profile was added.

monitor-session (interface-dynamic-template-BNG)

The support for this command under dynamic-template configuration mode was added for BNG.

test radius coa activate

This command was introduced.

timeout idle

The support for threshold and traffic keywords were added.

show ipsubscriber interface

The dynamic-routes keyword was added.

show subscriber feature accounting

The show command output was extended to display session Idle Timeout feature information.

show ethernet loopback active

This command was introduced.

show ethernet loopback permitted

This command was introduced.

monitor-session (interface)

The support for this command under dynamic-template configuration mode was added for BNG.

permit (IPv6)

The track keyword was added.

bootfile

This command was introduced.

clear dhcp ipv4 server binding

This command was introduced.

clear dhcp ipv4 server statistics

This command was introduced.

default-router

This command was introduced.

interface (DHCP)

The support for server profile was added.

lease (DHCPv4 Server)

This command was introduced.

limit lease

This command was introduced.

netbios-name-server

This command was introduced.

netbios-node-type

This command was introduced.

option

This command was introduced.

pool

This command was introduced.

profile (DHCP)

The server keyword was added.

requested-ip-address-check

This command was introduced.

show dhcp ipv4 server binding

This command was introduced.

show dhcp ipv4 server profile

This command was introduced.

show dhcp ipv4 server statistics

This command was introduced.

show dhcp vrf ipv4 server statistics

This command was introduced.

time-server

This command was introduced.

vrf (relay profile)

The server keyword was added.

domain name (IPAddr)

This command was supported for the DHCPv4 Server Profile submode.

igmp snooping disable

This command was introduced.

multicast p2mp

This command was introduced.

signaling-protocol

Support for this command in the L2VPN bridge group bridge domain VFI multicast P2MP configuration mode was introduced.

transport rsvp-te

This command was introduced.

debug spanning-tree pvrst

This command was introduced.

forward-delay (PVRST)

This command was introduced.

interface (PVRST)

This command was introduced.

maximum (PVRST)

This command was introduced.

show spanning-tree pvrst

This command was introduced.

spanning-tree pvrst

This command was introduced.

transmit (PVRST)

This command was introduced.

vlan (PVRST)

This command was introduced.

show qos-ea interface

This command was introduced.

interface (MPLS LDP)

The Bridge-Group Virtual Interface (BVI) configuration was added to support MPLS LDP over Integrated Routing and Bridging (IRB).

auto-tunnel p2mp

This command was introduced.

set ipv4 df

This command was introduced.

tunnel-id (auto-tunnel p2mp)

This command was introduced.

default-martian-check disable

This command was introduced.

bfd dampening

This command was introduced.

show bfd neighbor

This command was introduced.

autonomous-system

This command was added in address family configuration mode.

redistribute (EIGRP)

The eigrp keyword was added.

router eigrp

The virtual-instance-name support was added.

show ospf

The output of the command was modified to include OSPFv3 status.

protocol shutdown (OSPFv3)

This command was introduced.

sham-link (OSPFv3)

This command was introduced.

snmp-server mibs subscriber threshold

This command was introduced.

snmp-server mibs subscriber threshold access-if

This command was introduced.

snmp-server traps subscriber session-aggregation

This command was introduced.

storm-control

Support for storm control configuration for bridge domain was introduced. Also, a new unit kbps for storm control was introduced.

show l2vpn forwarding hardware ingress detail location

The command was introduced.

debug l2vpn forwarding platform vpls all location

This command was introduced.